Beruflich Dokumente
Kultur Dokumente
Caution indicates a hazard with a low level of risk which, if Set pressure of outlet pressure shall be 85% or less of inlet pressure. • A knob cover to prevent careless operation of the knob is available.
Caution
not avoided, could result in minor or moderate injury. Pressure over 85% makes operation susceptible to flow and inlet Refer to the catalogue for details.
Warning indicates a hazard with a medium level of risk pressure and may lead to unstable operation.
Warning Warning
which, if not avoided, could result in death or serious injury. P2 < P1 x 0.85
4 How to Order
• The system designer should determine the effect of the possible failure
Danger indicates a hazard with a high level of risk which, if Refer to the drawings or catalogue for ‘How to Order’. states on the system.
Danger
not avoided, will result in death or serious injury. 3 Installation 5 Outline Dimensions (mm) • Regulator is not to be used as a pressure relief valve, apply additional
Warning measure to relieve large volume of pressurised air.
3.1 Installation Refer to the drawings or catalogue for outline dimensions.
• Always ensure compliance with relevant safety laws and Warning
standards.
• All work must be carried out in a safe manner by a qualified person in • Do not install the product unless the safety instructions have been read Panel fitting dimensions
compliance with applicable national regulations. and understood. 8 Contacts
3.2 Environment Plate thickness
2 Specifications Refer to www.smcworld.com for contacts.
Warning
2.1 Specifications AR20(K)-B to AR30(K)-B: Max. 3.5
• Do not use in an environment where corrosive gases, chemicals, IN OUT AR40(K)-B : Max 5
Series AR-B water, salt water or steam are present.
Construction Relieving type • Do not use in an explosive atmosphere.
Fluid Air • Do not expose to direct sunlight. Use a suitable protective cover. URL : http// www.smcworld.com (Global) http// www.smceu.com (Europe)
Ambient and fluid temperature -5 to +60 °C (No freezing) Note 1) • Do not install in a location subject to vibration or impact in excess of 'SMC Corporation, Akihabara UDX15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101
the product’s specifications. 0021
Proof pressure 1.5 MPa Specifications are subject to change without prior notice from the manufacturer.
• Do not mount in a location exposed to radiant heat that would result in © 2018 SMC Corporation All Rights Reserved.
Max. operating pressure 1.0 MPa temperatures in excess of the product’s specifications. Optional specifications Template DKP50047-F-085H
Set pressure range 0.05 to 0.85 MPa Model Panel mount
Pressure gauge port size 1/8 Note 2) 3.3 Piping
W Y Z
Lubrication Not required (Refer to 3.4) Caution
Filtration 5 µm filtration or smaller AR20(K)-B 28.5 14 6
• Before connecting piping make sure to clean up chips, cutting oil, dust
Flow and pressure AR25(K)-B 32.5 16 6
See online catalogue etc.
characteristics • When installing piping or fittings, ensure sealant material does not AR30(K)-B 38.5 19 7
Weight See Table 2 enter inside the port. When using seal tape, leave 1 thread exposed
AR40(K)-B 42.5 21 7
Port size See Table 2 on the end of the pipe/fitting.
Shock resistance Note 3 300 m/s2 (nominal pulse 6 ms) • Tighten fittings to the specified tightening torque. AR40(K)-06-B 42.5 21 7
Vibration resistance Note 4 50 m/s2 AR50(K)-B – – –
Table 1
AR60(K)-B – – –
Page 1 of 1