Sie sind auf Seite 1von 8

Technical Specification

EJC 145 L06145-1 1/8

General Arrangement

177
(7)

(175)
4445
40°

(112)
2844
2057
(81)
1752
(69)

1397
(55)
12°
254
(10) 1524 2032
3048 (60) (80)
(120)
8839
(348)

1930
(76)
(1 997

42° 1
551 )
)
18
2

7
19 7)

(2 1
21 85)

59
(7
65
(

2.8 m
(9.25 ft)

Note: All vertical dimensions are for an empty unit and are
based on a tire radius of 26.5 " (673 mm).
Dimensions in brackets are in inches
Optional canopies shown.
EJC Mining Equipment reserves the right to
change this specification without notice
© 2006 EJC Mining Equipment

EJC Mining Equipment Revision Date: 2006-22-02


Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Technical Specification
EJC 145 L06145-1 2/8

Standard Unit Specifications

General Information Power Train


Main Dimensions Engine
Total length 8839 mm 348 in Diesel engine Detroit Diesel Series 40E
Width without bucket 2165 mm 85 in Output 141 kW (190 Hp) @ 2 300 rpm
Maximum width 2165 mm 85 in Torque 658 Nm (485 lbf-ft)@1 500 rpm
Height over FOPS canopy 2057 mm 81 in Number of cylinders In line, 6
Height over ROPS canopy 2334 mm 88 in Displacement 7.64 l (466 in³)
Cooling system Liquid cooled
Operating Weights
Combustion principle Turbo charged, after cooled,
Total operating weight 16497 kg 36348 lb. direct injected, 4 cycle
front axle 6599 kg 14548 lb. Air filtration Donaldson, dry type
rear axle 9888 kg 21800 lb. Electric system 24 V
Exhaust system ECS catalytic purifier with
Loaded Weights
silencer
Total loaded weight 23064 kg 50848 lb. Fuel tank capacity 181 l 48 US gal.
front axle 15812 kg 34859 lb.
rear axle 7252 kg 15989 lb. Converter
Dana SOH C 273, Stall torque ratio: 3.095:1
Capacities single stage Offset Ratio: 1.037:1
Tramming capacity 6577 kg 14500 lb.
Break out force, lift 76 kN 7711 kg 17000 lbf
Transmission
Break out force, tilt 89 kN 9071 kg 20000 lbf Dana SOH R32421 4-speed forward & reverse
Tipping load 17690 kg 39000 lb. with modulation
Standard bucket 3.0 m³ 4.0 yd³ Axles
Bucket Motion Times Front axle Dana SOH 16D2149, no-spin differential,
Raising time 6.0 sec. fixed
Lowering time 4.0 sec. Rear axle Dana SOH 16D2149 standard
Tipping time 4.0 sec. differential, oscillating ± 10°.

Driving Speeds Forward and Reverse Tires


(Loaded) Tire size 17.5 x 25, 20 PLY
Type L5S
1st gear 5.1 km/h 3.2 m.p.h.
Air pressure, front 552 kPa 5.52 bar 80 psi
2nd gear 10.8 km/h 6.7 m.p.h.
Air pressure, rear 552 kPa 5.52 bar 80 psi
3rd gear 17.5 km/h 10.9 m.p.h.
4th gear 28.1 km/h 17.5 m.p.h.

Frame Systems
Rear & front frame Welded steel box construction
Material G40.21 - 50WT. Cat.#3 Steering Hydraulics
Central hinge Welded steel box construction with Full hydraulic power steering, centre articulated with two
hardened steel spherical bearings double acting steer cylinders, open centre system with a
gear pump. Equipped with pilot operated control lever.
Material G40.21 - 50WT. Cat.#3
Tanks are welded to frame.
EJC Mining Equipment reserves the right to
change this specification without notice
© 2006 EJC Mining Equipment

EJC Mining Equipment Revision Date: 2006-22-02


Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Technical Specification
EJC 145 L06145-1 3/8

Turning Radius Other Standard Equipment


inner 2997 mm 118 in • Electric gauges
• Audible back-up alarm
outer 5562 mm 219 in • Central hydraulic pressure test points
Turning angle 42.0 ° • Central manual lubrication system
• SAE JIC hose fittings
Main Components
Manuals
Hydraulic pump Gear pump
All manuals are delivered on CD-ROM in web based
Control valve Pilot operated
format with Adobe PDF output for printing.
Steering cylinders EJC 3.5" bore x 2.0" rod

Pressure Settings Distribution


Manual Type Customer Market Area
Main relief 17.2 MPa 172 bar 2500 psi
Spare parts manuals 3 Copies 1 Copy
Port relief valves 18.6 MPa 186 bar 2700 psi
Operator’s manual 3 Copies 1 Copy
Bucket Hydraulics Service manual 3 Copies 1 Copy
Full hydraulic open-centre system with one gear pump.
Equipped with pilot operated joystick control lever, two
lift cylinders and one dump cylinder. Optional Equipment
Main Components Specifications
Lift cylinders EJC 6.5" bore x 3.0" rod
Dump Cylinder EJC 6.5" bore x 3.0" rod Available Alternative Equipment
Hydraulic pump Gear pump Deutz F8L-413FWB High altitude applications
Control valve Pilot operated Auto lube system Lincoln modular
Operator’s compartment Fully enclosed cab with a/c
Pressure Settings
Main relief 16.5 MPa 165 bar 2300 psi Alternative Bucket Options
Bucket dump 5.5 MPa 55 bar 800 psi Rock Volume Width
Bucket roll back 17.2 MPa 172 bar 2500 psi Bucket 2.7 m³ 3.5 yd³ 1930 mm 76 in
Lift arms raise/lower 17.2 MPa 172 bar 2500 psi with 500 3.1 m³ 4.0 yd³ 2083 mm 82 in
Pilot control 3.1 MPa 31 bar 450 psi BHN lip
Hyd. oil tank capacity 303 l 80 US gal. Ejector Volume Width
Buckets 2.7 m³ 3.5 yd³ 1930 mm 76 in
Standard Brakes
Service brakes are spring applied / hydraulically released, Available Add-On Options
liquid cooled multi-disc brakes on all wheels, with two Quick disconnect system (QDS) - master hitch
separate circuits for the front and rear axles. Service QDS bucket 2.7 m³ 3.5 yd³
brakes also function as an emergency brake, when the
QDS pallet forks
emergency brake system is engaged.
QDS dozer blade
Main Components QDS cable/belt reel
SAE, ROPS/FOPS canopy 88 in (2235 mm) o/a height
Pressure accumulator Piston type with charging valve
MSHA, FOPS canopy 81 in (2057 mm) o/a height
Brake pedal valve Modulated
Fire suppression Manual - Ansul 6 nozzles, 1 Tanks
Electrical Equipment systems Automatic (Checkfire II) - Ansul 6
Alternator 24V 60 A, min nozzles, 1 tanks
Batteries 2 x 12 V, 950 CCA Hand held fire extinguisher - 10 lb.
Starter 24 V, Heavy Duty Hand held fire extinguisher - 20 lb.
Driving and working lights 4pcs front, 4pcs rear Tamrock proportional RRC system (includes interface)
RRC interface only (specify receiver)
RRC fire suppression actuation button for Tamrock RRC
Hydraulic tow hook brake release
EJC Mining Equipment reserves the right to
change this specification without notice
© 2006 EJC Mining Equipment

EJC Mining Equipment Revision Date: 2006-22-02


Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Additional Information
EJC 145 L06145-1 4/8

Tractive Effort Curve (Metric Units)

EJC 145 (Metric Units)


160
ENGINE: Detroit Diesel Series 40E AXLES: 16D2149
CONVERTER: CLARK C273 TIRES: 17.5 x 25, 20 PLY L5S
150
TRANS: CLARK R32421 PAYLOAD: 6 363 kg
140
Rolling resistance (% )
130
Em pty Loaded

120
0 2 4 6 8 0 2 4 6 8

110

100

90
F (kN)

80

Grade (%)
70
30
60
25
50
30
20
40 25

20 15
30
15 10
20
10
5
10 5

0
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44
Speed (km/h)

EJC Mining Equipment reserves the right to


change this specification without notice
© 2006 EJC Mining Equipment
EJC Mining Equipment Revision Date: 2006-22-02
Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Additional Information
EJC 145 L06145-1 5/8

Tractive Effort Curve (US Units)

EJC 145 (Imperial Units)


ENGINE: Detroit Diesel Series 40E AXLES: 16D2149
CONVERTER: CLARK C273 TIRES: 17.5 x 25, 20 PLY L5S
36
TRANS: CLARK R32421 PAYLOAD: 14 500 lb
34

32

30
Rolling resistance (% )
28 Em pty Loaded

26 0 2 4 6 8 0 2 4 6 8

24

22
Tractive Effort (Klbf)

20

Grade (%)
18

16
30
14
25
12
30
10 20
25
8 15
20
6
15 10
4
10
5
2 5

0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
Speed (mph)

EJC Mining Equipment reserves the right to


change this specification without notice
© 2006 EJC Mining Equipment
EJC Mining Equipment Revision Date: 2006-22-02
Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Additional Information
EJC 145 L06145-1 6/8

Productivity Curve (Metric Units)

EJC 145 PRODUCTIVITY

450
Basic data for calculations:
Payload 6600 KG
400 Overall Speed limit 10 km/h
Fixed Cycle time 0.5 min

350 Fixed cycle time includes the time for filling, dumping, turning and accelerating

Slope/Grade (%) Hor./0 1:10/10 1:7/15 1:5/20


Loaded speed (km/h) 10 7.5 5.7 4
300
Empty speed (km/h) 10 10 10 10
TONNES PER HOUR

250

200

150

100

50

0
0 50 100 150 200 250 300 350 400 450
ONE WAY DISTANCE IN METRES

0% 10% 15% 20%

EJC Mining Equipment reserves the right to


change this specification without notice
© 2006 EJC Mining Equipment
EJC Mining Equipment Revision Date: 2006-22-02
Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Additional Information
EJC 145 L06145-1 7/8

Productivity Curve (US Units)

EJC 145 PRODUCTIVITY

500
Basic data for calculations:
Payload 14500 lbs
450 Overall Speed limit 6.2 mph
Fixed Cycle time 0.5 min

400 Fixed cycle time includes the time for filling, dumping, turning and accelerating

Slope/Grade (%) Hor./0 1:10/10 1:7/15 1:5/20


350 Loaded speed (mph) 6.2 4.7 3.5 2.5
Empty speed (mph) 6.2 6.2 6.2 6.2
300
TONS PER HOUR

250

200

150

100

50

0
0 200 400 600 800 1000 1200 1400
ONE WAY DISTANCE IN FEET
0% 10% 15% 20%

EJC Mining Equipment reserves the right to


change this specification without notice
© 2006 EJC Mining Equipment
EJC Mining Equipment Revision Date: 2006-22-02
Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com
Additional Information
EJC 145 L06145-1 8/8

Weights and Dimensions

228
(5791)
(5) Bucket, canopy, lift arms , left and right outriggers,
348 front fenders, axles and tires removed
(8839) Weight: 15648 lbs (7098 kg)
(1) Operating condition
Weight: 36348 lbs (16487 kg)

154
(3912)
(6) Rear frame bare
Weight: 3500 lbs (1590 kg)
290
(7336)
(2) Bucket and canopy removed
Weight: 25948 lbs (11768 kg)
(7) Front frame bare
Weight: 2600 lbs (1180 kg)

236
(5994)
(3) Bucket, canopy and lift arms removed
Weight: 24448 lbs (11089 kg)
(8) Lift arms bare
Weight: 2600 lbs (1180 kg)

228
(5791)

EJC Mining Equipment reserves the right to


(4) Bucket, canopy, lift arms , axles and tires removed (9) Bucket 3.0 yd³ (2.3 m³)

change this specification without notice


Weight: 18648 lbs (8459 kg) Weight: 3000 lbs (1364 kg)

© 2006 EJC Mining Equipment


EJC Mining Equipment Revision Date: 2006-22-02
Division of Sandvik Mining and Construction Canada Inc.
4445 Fairview Street, Burlington Ontario, Canada L7L 2A4 Email: ejc.loaders@sandvik.com
Tel.: (905) 632-4940 Web: http://www.ejc.sandvik.com

Das könnte Ihnen auch gefallen