Beruflich Dokumente
Kultur Dokumente
Summit Industrial Products
9010 CR 2120 ~ Tyler, TX 75707
P.O. Box 131369 ~ Tyler, TX 775713
Phone: 903.534.8021
Toll Free: 800.749.5823 ~ Fax: 800.749.1375
www.klsummit.com
www.sublimedescaler.com
info@klsummit.com
http://distributors.klsummit.com
WATER SCALE SOLVENT
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
ALIMEX
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
A WATER SCALE SOLVENT SAFE FOR ALUMINUM
Alimex is a water-based chemical formulated to safely clean lime scale and corrosion
from water-wetted surfaces. It contains wetting agents, corrosion inhibitors and
degreasing compounds to help penetrate and carry away the scale and corrosion. This
product is specifically designed to be used on equipment that contains aluminum that
cannot be safely cleaned with other scale removing compounds.
When used as directed, Alimex is non-corrosive and will not affect the following met-
als: aluminum, stainless steel, carbon steel, brass, admiralty metal, copper, iron, lead,
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
PVC plastic, polyethylene, rubber, leather, and most other materials found in water-
wetted equipment. Alimex is not recommended for zinc, galvanized steel, or alloys of
magnesium.
Alimex has a built-in indicator which changes color when the solution is 95+ percent
May 13, 2002
spent. When the solution begins to turn blue, it should be added to or changed if the
equipment is not clean.
DIRECTIONS
Alimex is designed to be used at ambient temperatures above 35ºF. It is most effec-
tive when circulated through the equipment to be cleaned. When possible, circulation
should be up-flow. Alimex can also be used by filling the equipment to be cleaned and
allowing it to set until the scale disappears. When cleaning exposed surfaces (such as
fin fan coolers), Alimex should be periodically sprayed on the surface until the scale
disappears. In all cases, fresh water should be used to rinse the clean surface free of
Alimex. The cleaning operation normally takes two to six hours. The equipment
should be vented at all times since carbon dioxide (CO2) gas evolves during the disas-
sociation of lime scale.
When the cleaning process is complete, the system should be completely drained and
flushed with fresh water.
PHYSICAL PROPERTIES
Specific Gravity 1.162
Freezing Point 28.4ºF
Boiling Point 208ºF
Flash Point None
Temperature of Reaction Negligible
Page 1 of 2
METHOD OF APPLICATION
Alimex solution is most effectively used by circulating it through the equipment to be cleaned.
When possible, circulation should be up flow. The equipment should be vented at all times
since carbon dioxide (CO2) gas is liberated from the disassociation of the lime scale.
Page 2 of 2
SYNTHETIC AIR COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
AU- 46 Silicone Based Fluid
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
AU-46 is a silicone-based fluid designed for use in rotary
screw compressors. AU-46 does not break down
under normal operating temperatures and pressures thereby
eliminating carbon deposits, sludge and varnish formations.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
May 13, 2002
PRODUCTS AU-46
Viscosity
@ -28°C, cSt 214
@ 25°C, cSt 50.8
@ 40°C, cSt 37.9
@ 100°C, cSt 15.5
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
BARRIER FLUID E
Product Data Sheet Summit Barrier Fluid E is formulated from the highest quality syn-
thetic base stocks and fortified with additives to provide a
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
non-reactive, oxidatively stable fluid for seal service over an
extremely wide temperature range. This fluid has an excellent low
temperature fluidity and high temperature stability property as well
as the ability to efficiently transfer heat, and keep the seal face cool.
Summit Barrier Fluid E does not contain components that are
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
BARRIER FLUID E
Viscosity
@ 40°C, cSt 31.0
@ 100°C, cSt 5.9
NSF Registered H1
Kosher Yes
Halal Yes
CFIA Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC BARRIER FLUIDS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
BARRIER FLUID SERIES
Product Data Sheet Summit Barrier Fluid Series lubricants are formulated from the
highest quality synthetic base stocks and fortified with additives to
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
provide a non-reactive, oxidatively stable fluid for seal service
over an extremely wide temperature range. These fluids have
excellent low temperature fluidity and high temperature stability
properties as well as the ability to efficiently transfer heat, and
keep the seal face cool. Summit’s Barrier Fluid Series lubricants
do not contain components that are known catalyst poisons, and
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Barrier Fluid Series products are NSF Registered and meet USDA
1998 (H1) guidelines (lubricants with incidental food contact) for use
in food plants. Do not add directly to food. Summit is an ISO 21469
September 5, 2012
certified facility.
Physical Properties
BARRIER FLUIDS 5 17 30 46 68
Viscosity
@ 40°C, cSt 5.1 16.9 30.5 46.0 66.0
@ 100°C, cSt 1.7 3.9 5.9 7.8 10.0
NSF Registered H1 H1 H1 H1 H1
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
PUMP/VACUUM PUMP
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying
Product Data Sheet
CentriPump PPO Series
Summit CentriPump PPO Series lubricants are a blend of premium
synthetic and petroleum base fluids specially designed for centrifugal
conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
pump applications. The CentriPump PPO Series offers superior
rust and corrosion properties, oxidation life and anti-wear protection.
They are exceptional at controlling sludge and deposits which results
in lower operating temperatures and extended oil drain intervals.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS PPO-32 PPO-46 PPO-68 PPO-100
August 6, 2013
Viscosity
@ 40°C, cSt 29.6 45.9 64.4 101.2
@100°C, cSt 5.12 6.8 8.6 11.2
@100°F, SUS 153 237 329 505
@210°F, SUS 43.4 48.6 54.2 63.7
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying
CentriPump SPO Series
Product Data Sheet Summit CentriPump SPO Series lubricants are manufactured from
the highest quality PAO (polyalphaolefin) base stocks and advanced
conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
additive technology. CentriPump SPO Series lubricants are recom-
mended for centrifugal pumps and present many advantages over
petroleum-based lubricants as well as other popular synthetic based
products. The CentriPump SPO Series offers superior oxidation life
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS SPO-32 SPO-46 SPO-68 SPO-100
August 6, 2013
Viscosity
@ 40°C, cSt 32.0 43.2 64.0 96.6
@100°C, cSt 5.80 7.34 10.0 13.2
@100°F, SUS 163 220 339 482
@210°F, SUS 45.7 50.4 59.6 69.8
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
CO-150 Tenter Chain Oil
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
base stocks. This blend contains an additive system
formulated to meet the demanding requirements for a tenter
chain lubricant.
The formulation of Summit CO-150 incorporates an additive
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
Characteristic Typical Performance
Viscosity
@ 100°F, cSt 111.2
@ 210°F, cSt 13.7
@ 100°F, SUS 515
@ 210°F, SUS 72.5
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
CO-250 High Temp Chain Oil
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
CO-250 should be used for the chains, steel belts and heated
press platens found in continuous particle board and wood
laminate machinery.
FEATURE BENEFIT
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
Characteristic Typical Performance
November 4, 2010
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying
CO-400 High Temp Chain Oil
Product Data Sheet Summit CO-400 High Temperature Chain Oil is a unique
formulation of special ester base stocks and the latest additive
conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
technology. CO-400 has an exceptionally high smoke point
and is capable of penetrating and removing carbonaceous
deposits and inhibiting the formation of solid buildup. It is
effective over a broad temperature range and results in lower
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
APPLICATIONS:
Summit CO-400 High Temperature Chain Oil is recommended for
use in the following applications:
•High Temperature Process Ovens •Drying Operations
•Can and Fibre Board Lines •Glass Fibre Ovens
•Extrusion Paint Lines •Multi-Purpose E.P. Gears
•Tenter Frames
October 14, 2010
Physical Properties
Characteristic Typical Performance
ISO Grade 150
Viscosity
@ 100°F, cSt 154.8
@ 210ºF, cSt 19.05
@ 100°F, SUS 717
@ 210ºF, SUS 94.48
NSF Registered H2
SYNTHETIC OVEN CONVEYOR CHAIN LUBRICANT
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
CO-95 High Temp Chain Oil
Summit CO-95 High Temperature Chain Lubricant was
developed specifically for the conveyor chains used in fiber-
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current .
glass, rockwool, and gypsum ovens. It is a proven quality
high temperature roller chain lubricant.
Feature Benefit
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
November 4, 2010
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
DSL®-100S
Physical Properties
PRODUCT DSL®-100S
Viscosity:
@ 40°C, cSt 86
@ 100°C, cSt 8.5
@ 100°F, SUS 454
@ 210°F, SUS 54.9
Viscosity Index 55
Copper Corrosion 1A
SPECIAL NOTE: Summit DSL® lubricants are not compatible with almost all
elastomers used in compressors and pumps including the paint used in crankcases.
Consult the Material Compatibility Guide for specific recommendations.
SYNTHETIC AIR COMPRESSOR
Note: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
DSL®-1220
Physical Properties
PRODUCTS DSL®-1220
October 13, 2010
Viscosity:
@ 40°C, cSt 227
@ 100°C, cSt 27.5
@ 100°F, SUS 1450
@ 210°F, SUS 133.9
Autoignition Point,
°F (°C) 790 (421)
Copper Corrosion 1A
Summit DSL ® synthetic lubricants are unique combinations of quality diester base
stocks and the latest additive technology.
Summit provides a wide range of DSL® lubricants that cover applications for rotary vane,
rotary screw, and all ages and design types of reciprocating
compressors.
Summit DSL ® lubricants are especially noted for the following benefits:
•Low temperature fluidity
•Better thermal conductivity-reduces operating temperature
•Reduced friction – approximately 20% lower coefficient of friction.
•High temperature thermal stability will not disassociate under thermal stress.
•Greater resistance to mechanical stress will not shear under heavy loads or extreme stress.
•Reduced metal-to-metal wear-polar properties provided better metal wetting
•Better demulsibility characteristics-moisture separates readily, providing better rust and
corrosion protection.
•More energy efficiency.
These lubricants are designed for use in the crankcase and as a cylinder lubricant. They are
compatible with almost all elastomers used in compressors and pumps, including paint used
in crankcases.
COMPATIBILITY:
The following materials are compatible for use with DSL® lubricants:
Epoxy Paint, Celcon, Viton®, High Nitrile Rubber (Buna N, NBR-greater than 36%
Acrylonitrile), Medium Nitrile Rubber (Buna N, NBR 30-36% Acrylonitrile), Teflon®, Oil
Resistant Alkyd, and Nylon.
Page 1 of 2
June 28. 2007
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
®
DSL SERIES (Diester) Physical Properties
PRODUCTS DSL®-32 DSL®-46 DSL®-68 DSL®-100 DSL®-125 DSL®-150
®
Pour Point, °F(°C) -65 (-54) -65 (-54) -40 (-40) -30 (-34) -38 (-39) -30 (-34)
Flash Point, °F(°C) 490 (254) 475 (246) 490 (254) 495 (257) 495 (257) 505 (263)
DSL SERIES (Diester)
SYNTHETIC AIR COMPRESSOR
Autoignition Point ,°F(°C) 765 (407) 720 (373) 765 (407) 780 (416) 785 (418) 785 (418)
Copper Corrosion 1A 1A 1A 1A 1A 1A
*DSL®125 falls between the ISO-100 and ISO 150 viscosity range. DSL®1220 Available upon request
with some elastomers used in compressors and pumps including
SPECIAL NOTE: Summit DSL® lubricants are not compatible
Note: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
DSL®-100XM
Physical Properties
PRODUCTS DSL®-100XM
October 14, 2010
Viscosity Index 94
Copper Corrosion 1A
Rust Pass
Special Note: Summit DSl® lubricants are not compatible with almost all
elastomers used in compressors and pumps including the paint used in crankcases.
Consult the Material Compatibility Guide for specific recommendations.
BIODEGRADABLE TRACTOR HYDRAULIC OIL
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
ENVIROTECH® ALL-TRAC
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of November 14, 2007.
EnviroTech® All-Trac is an environmentally responsible universal lubricant
for farm equipment, off-highway machinery, and industrial tractors. This
multifunctional biobased fluid is designed for equipment requiring one
lubricant for the transmission, final drive, wet brakes and hydraulic systems.
It meets or exceeds the performance requirements of all major brands of
farm tractors and other farm equipment that utilize a common fluid reservoir.
EnviroTech® All-Trac is formulated with special friction modifiers to
ensure proper operation of wet brakes and transmission clutch packs. The
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
ENVIROTECH ®
ALL-TRAC
Viscosity
@40°C, cSt 47.8
@100°C, cSt 10.26
Brookfield Viscosity
@-20°C 1650
@-35°C 11,150
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
ENVIROTECH® CO FG Series
Physical Properties
EnviroTech ®
CO-68 FG CO-150 FG
ISO Grade 68 150
Viscosity (ASTM D-445)
@40ºC 67.5 147.1 cSt
@100ºC 12.5 24.9 cSt
Viscosity Index (ASTM D-2270) 187 203
Flash Point (ASTM D-92) 590ºF / 310ºC 595ºF / 313ºC
Fire Point (ASTM D-92) 635ºF / 335ºC 640ºF/ 338ºC
Pour Point (ASTM D-97) -18.4ºF/-28ºC -13ºF/-25ºC
Rust Prevention (ASTM D-665) Pass Pass
4 Ball Wear (ASTM D-2266) 0.40 0.40
4 Ball Weld (ASTM D-2783) 160 kg 160 kg
NSF Registered H1 H1
SPECIAL INSTRUCTIONS:
Because of the high concentration of white graphite in this chain oil, it needs
agitation before use to insure even distribution of the solid lubricant. The white
graphite has proven to stay in suspension for up to two weeks after being introduced
into a capillary tube supplying lubricant to an applicator.
Shelf Life: Product shelf life is 3 years from the date of manufacture, after which
the product should be recertified prior to use.
BIODEGRADABLE EP GEAR LUBRICANT
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
ENVIROTECH®
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 6, 2009.
EnviroTech® EP Gear Oils are environmentally responsible lubricants
designed for the protection of gears and bearings in systems where high
temperature and/or extreme pressure conditions exist. It is a vegetable
based formulation recommended for lubricating spur, helical, bevel, and
worm gear configurations. These biobased lubricants are intended for
heavy-duty applications subject to heavy loading or shock loading.
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
EnviroTech® EP-150 EP-220 EP-320 EP-460
ISO Grade, Approximate 150 220 320 460
AGMA #, Approximate 4 EP 5 EP 6 EP 7 EP
Specific Gravity 0.900 0.903 0.900 0.908
Viscosity
@40°C, cSt 131 166 252 382
@100°C, cSt 20 24.1 34 49
Viscosity Index 175 177 182 194
Pour Point °F(°C) -8(-22) -4(-20) 0(-18) 10(-12)
Flash Point °F(°C) (550)288 536(280) 536(280) 536(280)
Copper Corrosion 1A 1A 1A 1A
Rust Test Pass Pass Pass Pass
Timken OK, lbs 70 70 70 70
Four-Ball Wear 0.3 0.3 0.3 0.3
Four-Ball EP
Weld Point (kg) 250 250 250 250
Four-Ball EP Load
Wear Index 47.86 47.86 47.86 47.86
FZG Test 12 12 12 12
Biodegradation
Classification, ultimate ultimate inherent inherent
ASTM D 5864 PW1 PW1
BIODEGRADABLE FOOD GRADE PENETRATING OIL
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
ENVIROTECH® FGPL
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of November 24, 2010.
Summit EnviroTech® FGPL is a biobased food grade penetrating
lubricant formulated for use in the food processing industry. This
biodegradable formulation is odorless and tasteless. It is fast
acting and rapidly penetrates corrosion or carbon residue on equip-
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
ment. It is suitable for use on all metals and alloys. Summit FGPL
can be used on food processing equipment as a protective anti rust
film, as a release agent on gaskets or seals of tank closures and as
a lubricant for machine parts in locations where the potential for
exposure to food exists.
November 24, 2010
Physical Properties
EnviroTech® FGPL
Specific Gravity @ 60ºF .88
Viscosity @40ºC 14
Rust Prevention
NSF Registered H1
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
BIODEGRADABLE HYDRAULIC OIL
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
EnviroTech® H Series
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of November 16, 2010.
EnviroTech® hydraulic oils are premium environmentally responsible
hydraulic fluids designed to provide exceptional performance in hydraulic
and circulation systems. These vegetable based formulations have been engi-
neered to meet or exceed the performance requirements of most hydraulic
pump and system manufacturers, while satisfying the rigorous criteria for
biodegradability and toxicity. They offer the anti-wear and film strength
characteristics necessary for hydraulic systems operating under high load
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
and high pressure. EnviroTech® hydraulic oils are inhibited for excellent
protection against rust and corrosion. In addition to their excellent per-
formance capability, EnviroTech® hydraulic oils satisfy the requirements for
ultimate biodegradability and non-toxicity making them an excellent choice
for hydraulic and circulation systems operating in environmentally sensitive
areas. Base oils and additives in these products pass and exceed the acute
toxicity (LC-50) criteria adopted by the U.S. Fish and Wildlife Service
and the U.S. EPA.
EnviroTech® meets the definition of a biobased lubricant as outlined in
section 9001 of The Farm Security and Rural Investment Act (FSRIA) of
November 16, 2010
2002 (Public Law 107-171/ HR 2642) and qualifies for preferred pro-
curement by U.S. Federal Agencies as set forth in FSRIA section 9002
Physical Properties
EnviroTech® H-32 H-46 H-68
ISO Grade 32 46 68
Specific Gravity 0.875 0.877 0.888
Viscosity
@ 40°C, cSt 31.3 43.5 64.6
@ 100°C, cSt 6.80 9.80 12.73
Viscosity Index 185 220 201
Flash Point, °F (°C) 460 (238) 470 (243) 485 (252)
Fire Point, °F (°C) 505 (263) 510 (266) 520 (271)
Pour Point, °F (°C) -40 (-40) -35 (-37) -30 (-34)
FZG Gear Test, 12 12 12
DIN 51354
4-Ball Wear, 0.38 0.35 0.34
ASTM D 4172, mm
Biodegradadation ultimate ultimate ultimate
Classification,
ASTM D 5864 PW1 PW1 PW1
Emulsion Tendency 40/40/0 40/40/0 40/40/0
ASTM D1401 (10) (10) (10)
EnviroTech® H Series lubricants do not produce an iridescent appearance
(sheen) on the surface of the water when tested in accordance with the U.S.
Coast Guard Static Sheen Test.
SYNTHETIC AIR COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
FF SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of January 4, 2005
Summit FF Series lubricants are formulated from the best diester
base stocks available and employs state-of-the-art additive tech-
nology to provide outstanding high temperature performance in
reciprocating air compressors.
FF-100 and FF-150 are excellent lubricants for the following
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
applications:
• Reciprocating compressor cylinders used in fire flood operations
and other environments sensitive to combustion.
• Low and High temperature lubrication
• General lubrication
Physical Properties
January 4, 2005
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
FG ELITE SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
industry. These lubricants use 100% multisynthetic base oils in
combination with performance driven additives to offer extended
lubricant life. Field tests have shown these lubricants will last
between 8,000 and 10,000 hours depending on operating conditions.
In addition, this innovative chemistry offers increased solvency,
which significantly reduces deposit and sludge formation. Summit
FG Elite Series lubricants offer superior protection against rust,
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
FG Elite Series 32 46 68 100 150
April 10, 2013
Viscosity
@ 40°C, cSt 33.0 45.5 67.1 103.0 148.0
@ 100°C, cSt 5.9 7.5 10.1 14.0 18.5
NSF Registered H1 H1 H1 H1 H1
Shelf Life: Product shelf life is 3 years from the date of manufacture, after which the
product should be recertified prior to use.
SYNTHETIC AIR COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
FG SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
service industry. These fully synthetic lubricants are NSF Registered
and meet USDA 1998 (H1) guidelines (lubricants with incidental food
contact). Summit FG Series lubricants are Kosher/Halal certified and
CFIA accepted. Summit is an ISO 21469 certified facility.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
FG SERIES FG-100 FG-200 FG-250 FG-300 FG-500
ISO Grade 32 46 68 100 150
Viscosity
March 9, 2012
Autoignition Point,
ºF (ºC) 730(388) 745(396) 750(399) 760(404) 770(410)
Emulsion Tendency 40/40/0(10) 40/40/0(5) 40/40/0(10) 40/40/0 (5) 43/37/0(10)
NSF Registered H1, HT1 H1 H1 H1 H1
ISO 21469 Yes Yes Yes Yes Yes
Kosher Yes Yes Yes Yes Yes
Halal Yes Yes - Yes Yes
CFIA Yes Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
May 13, 2002
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Viscosity:
PRODUCT
@ 40°C, cSt
Viscosity Index
@ 100°C, cSt
Specific Gravity
62
38
5.4
.967
SYNTHETIC SYSTEM FLUSH
435 (224)
-43.6 (-42)
Physical Properties
Flushing Oil
detergency, dispersancy, and biodegradability properties.
flushing lubricant circulating systems. It has excellent
Summit Flushing Oil is a diester based product designed for
NATURAL GAS ENGINES
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
GEO PS
Product Data Sheet GAS ENGINE OIL SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
Summit Gas Engine Oils are manufactured from a blend of
synthetic and petroleum base stocks. They are recommended
for service in two-cycle and four-cycle gas engines, naturally
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
July 24, 2013
SAE Grade 30 40
Viscosity
@ 40°C, cSt 96.0 119.2
@ 100°C, cSt 11.1 13.5
Foaming Tendency
Seq I NIL NIL
Seq II NIL NIL
Seq III NIL NIL
Copper Corrosion 1A 1A
Sulfated Ash, % wt. .45 .50
Customer Benefits:
Reduced oil consumption
Superior lubrication at all temperatures
Longer engine life
Faster starting in cold weather conditions
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
NATURAL GAS ENGINES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
Summit GEO SH Gas Engine Oils are 100% full synthetic, PAO Ester
Formulations for 2-cycle and 4 cycle lean burn and stoichiometric natural gas
engines. Summit GEO SH-130 and GEO SH-140 are low ash with excellent
TBN retention to combat oil degradation and provide protection in high tem-
perature acidic environments. GEO SH Series was developed with field tested
robust detergent/dispersant additive technology, balanced to keep pistons clean
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
and low valve recession while minimizing spark plug fouling. Summit GEO SH
Series Oils are recommended for four-stroke, high speed natural gas engines
where Group II base products deteriorate prematurely or overheat under severe
continuous high temperature operation.
The end user benefits for Summit GEO SH Series include:
• Maximum Maintenance Flexibility
• Engine Uptime & Maximum Heat Release
• Excellent Fuel Efficiency & HP Improvement (BHP-hr)
• Cleaner Engine Operation & Prevents Ring Sticking
• Extended Drains Beyond Group II Based GEOs
• Excellent Low Temperature Pour and Cranking
July 24,2013
Physical Properties
PRODUCTS GEO SH-130 GEO SH-140
SAE Grade 30 40
Viscosity
@ 40°C, cSt 78.0 94.2
@ 100°C, cSt 12.1 13.5
Viscosity Index 151 144
Flash Point, °F (°C) 485 (252) 550 (288)
Pour Point, °F (°C) -40 (-40) -53 (-47)
Foaming Tendency
Seq I NIL NIL
Seq II NIL NIL
Seq III NIL NIL
Copper Corrosion 1A 1A
Sulfated Ash, % wt. .50 .50
TBN 5.50 5.50
SYNTHETIC GAS ENGINES
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
GEO SH
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
GAS ENGINE OIL SERIES
Summit Synthetic Gas Engine Oils are recommended
for service in two or four cycle gas engines, naturally
aspirated and turbo-charged. Summit GEO SH-30 and
GEO SH-40 are ashless and have an excellent gas
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
May 13, 2004
Viscosity
@ 40°C, cSt 78.0 100.0
@ 100°C, cSt 12.1 14.6
Viscosity Index 151 155
Foaming Tendency
Seq I NIL NIL
Seq II NIL NIL
Seq III NIL NIL
Copper Corrosion 1A 1A
Customer Benefits:
Reduced oil consumption
Superior lubrication at all temperatures
Longer engine life
Faster starting in cold weather conditions
PREMIUM WHITE OIL HYDRAULIC
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYPAR FG SERIES
Product Data Sheet Summit HyPar FG Series hydraulic oils are formulated specially for
hydraulic systems operating in the food service, beverage, and
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
packaging industry. These premium white oil lubricants are NSF
Registered and meet USDA 1998 (H1) guidelines (lubricants with inci-
dental food contact). HyPar FG Series lubricants are Kosher certified
and CFIA accepted. Summit is an ISO 21469 certified facility.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
HYPAR FG FG-15 FG-22 FG-32 FG-46 FG-68 FG-100
ISO Grade 15 22 32 46 68 100
March 9, 2012
Viscosity
@ 40°C, cSt 15.4 22.3 32.0 42.0 68.0 97.2
@ 100°C, cSt 3.41 4.30 5.38 6.41 8.76 11.14
@ 100°F, SUS 84.1 116.7 165.4 216.0 352.0 505.0
@ 210°F, SUS 37.8 40.7 44.3 47.7 55.8 64.4
Viscosity Index 91 96 101 101 101 100
NSF Registered H1 H1 H1 H1 H1 H1
ISO 21469 - Yes Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture,
after which the product should be recertified prior to use.
PREMIUM SYNTHETIC BLEND HYDRAULIC
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYPAR SERIES
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of November 16, 2010.
Summit HyPar ashless hydraulic oils are formulated to meet
the requirements of all types of hydraulic systems. HyPar
oils are rust and oxidation inhibited to protect against
rust, wear and the formation of sludge. They are compatible with
seal materials normally used in hydraulic systems.
Summit HyPar ashless hydraulic oils contain additives
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS 22 32 46 68 100
November 16, 2010
Specific
Gravity 0.858 0.860 0.864 0.869 0.874
Viscosity
@ 40°C, cSt 22.0 33.0 45.2 69.0 100
@ 100°C, cSt 4.27 5.47 6.67 8.67 11.5
@ 100°F, SUS 115 171 240 357 542
@ 210°F, SUS 40.6 44.6 48.6 55.4 65.7
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYSYN-22
Product Data Sheet Summit HySyn-22 ashless hydraulic oil is formulated from
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
the highest quality synthetic hydrocarbons to meet the
requirements of all types of hydraulic systems. HySyn 22 is
rust and oxidation inhibited and protects against the formation
of sludge. It is compatible with seal materials normally used in
hydraulic systems.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCT HYSYN-22
ISO Grade 22
Specific Gravity 0.821
Viscosity
@ 40°C, cSt 20.8
@ 100°C, cSt 4.48
@ -40°C, cSt 3298
Brookfield
Viscosity @ -40°C, cP 3340
Viscosity Index 130
Flash Point, °F (ºC) 425 (218)
Fire Point, °F (ºC) 475 (246)
Pour Point, °F (ºC) -85 (-65)
Demulsibility 40/40/0 (5 mins.)
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYSYN FG SERIES
Product Data Sheet Summit HySyn FG Series hydraulic oils are formulated specially for
.
hydraulic systems operating in the food service, beverage, and pack-
aging industry. These fully synthetic lubricants are NSF Registered
and meet USDA 1998 (H-1) guidelines (lubricants with incidental food
contact). HySyn FG Series lubricants are Kosher/Halal certified and
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current `
pending CFIA approval. Summit is an ISO 21469 certified facility.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
HYSYN FG FG-15 FG-22 FG-32 FG-46 FG-68 FG-100
ISO Grade 15 22 32 46 68 100
March 9, 2012
Viscosity
@ 40°C, cSt 15.0 21.7 30.7 46.8 68.4 99.3
@ 100°C, cSt 3.58 4.56 5.80 7.79 10.4 13.9
@ 100°F, SUS 82 113 157 238 350 510
@ 210°F, SUS 38.3 41.6 45.7 52.3 61.5 74.9
Viscosity Index 122 127 134 135 139 141
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYSYN FR SERIES
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
HYSYN SERIES
Product Data Sheet
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 3, 2011.
Summit HySyn ashless hydraulic oils are formulated from the
highest quality synthetic hydrocarbons to meet the requirements
of all types of hydraulic systems. HySyn oils are rust and oxi-
dation inhibited to protect against rust, wear and the formation
of sludge. They are compatible with seal materials normally
used in hydraulic systems.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS 15 32 46 68 100
May 3, 2011
Viscosity
@ 40°C, cSt 15.5 32.0 43.5 64.1 95.0
@ 100°C, cSt 3.63 5.80 7.25 9.60 12.7
@ 100°F, SUS 84.6 163 223 329 491
@ 210°F, SUS 38.5 45.7 50.4 58.7 70.6
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
LCG Series
Summit LCG Series are specially formulated compressor lubricants designed to be inert
to reactive and corrosive gases encountered in landfills, refineries, EOR and chemical
process plants. LCG Series is based on 100 % pure synthetic PAO. It’s extremely low
vapor pressure results in minimal carryover past the separator. It does not contain sulfur
or other impurities associated with petroleum based products that might react with the
acids, chlorinated compounds or sour gases found in various applications. PAOs are
fully saturated compounds and do not contain the alkenes or aromatics found in group I,
II or even the group III mineral oils touted as being "pure." LCG Series is ester free and
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
not subject to hydrolysis issues encountered with most esters when used in acidic envi-
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability.
ronments. LCG Series is suitable for use in certain chloride containing environments
where the use of mineral oil, esters or synthetic polyglycols (PAGs) are not permitted.
Lubricants that are reactive with a gas stream may form by-products that are harmful to
equipment or the environment. Solids may form and cause fouling or plugging issues in
certain applications.
Summit LCG Series will protect oil wetted parts against the corrosive effects of common
acids and water. It is engineered with superior technology to inhibit the effects of sour
gases such as hydrogen sulfide or carbon dioxide on metal surfaces found within the oil
wetted parts of a compressor.
Summit LCG Series is designed to result in longer fluid and equipment life for rotating
compressors in corrosive and reactive environments. Please consult with a Summit
May 11, 2011
Industrial Products lubrication expert about the suitability of LCG Series in these types
of applications.
Physical Properties
PRODUCTS LCG-68 LCG-100
ISO Grade 68 100
Viscosity
@ 40°C, cSt 69.4 99.3
@ 100°C, cSt 10.8 13.9
@ 100°F, SUS 353 510
@ 210°F, SUS 63 75
Viscosity Index 146 142
Pour Point, °F (°C) -40 (-40) -40 (-40)
Density, g/ml, 60°F 0.8371 0.8381
100°F 0.8235 0.8264
185°F 0.7931 0.7958
Flash Point, °F (°C) 510 (266) 530 (277)
Fire Point, °F (°C) 570 (299) 580 (304)
Vapor Pressure, mmHg (torr)
100°F 0.0001 0.0001
200°F 0.0004 0.0003
300°F 0.0015 0.0013
Molecular Weight 765 895
THERMAL CHARACTERISTICS:
Specific Heat Thermal Conductivity
Cal/g-ºC BTU hr -1 ft-1 F-1
167ºF = 0.544 @100ºF = 0.089
212ºC = 0.565 @200ºF = 0.088
@300ºF = 0.087
SYNTHETIC BLEND AIR TOOLS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
LUBEAIR
and chucks.
•Lubeair-68 is for large drills, grinders, vibrators, hand-held tools
and jack hammers.
Physical Properties
PRODUCTS LUBEAIR-32 LUBEAIR-68
ISO Grade 32 68
Viscosity
@ 40ºC, cSt 31.93 69.40
@ 100ºC, cSt 5.37 8.88
@ 100ºF, SUS 165 359
@ 210ºF, SUS 44.3 56.2
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
LUBEAIR FG-22
Product Data Sheet Summit Lubeair FG-22 air line lubricant is formulated specifi-
cally for pneumatic tools used in the food service, beverage,
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
and packaging industries. This lubricant is NSF Registered and
meets U.S.D.A. 1998 (H1) guidelines (lubricants with possible
incidental food contact). Summit is an ISO 21469 Certified
facility.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
April 2, 2013
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC AIR COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
LUBRICANT COOLANT
Product Data Sheet Summit Lubricant Coolant is formulated from the best
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
diester base stocks available and employs state of the
ar t a d d i t i v e technology to provide an outstanding
lubricant and coolant. Lubricant Coolant is an excellent
lubricant for the applications listed below. Please consult
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCT LUBRICANT COOLANT
ISO Grade 68
Viscosity:
@ 40°C, cSt 65.0
September 4, 2012
Viscosity Index 97
Color Blue
Recommended Applications:
Rotary screw and vane compressors
Ball and roller bearings
Low temperature lubrication
High temperature lubrication
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
MORCON-10
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
Tough on Concrete & Mineral Deposits
Cement in its various forms, is one of the primary construction materials of the
modern world. It is used in things we see and use every day. We drive on it, we
construct buildings with it, we dam rivers with it, and we even make boats with
it. Cement is a very versatile material.
MORCON-10 ...CAN:
We also get it in a lot of places we don’t want it to be. Morcon-10 was devel-
oped to remove cement and other calcium materials (lime-scale, barnacles, mus-
sels) from places where they may cause a problem.
face.
• Remove cement and concrete from trucks, building forms, concrete mixers,
pumps, and all sorts of construction equipment.
• Remove barnacles from propellers, skegs, rudders, and hulls of sea going ves-
sels.
• Remove barnacles and mussels from pipe, screens, pumps, and exchangers in
power plants.
MORCON-10 ...WILL:
• Not harm most paints and metals including brass and cop-
per when used as directed.
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
NGL Series
• The carryover from increased lubricant feed rates or use of heavily compounded
oils to compensate for hydrocarbon and CO2 dilution and wash-out can damage
the well formation and plug CO2 injectors.
• Gases such as CO2 and H2S may be corrosive to compressor components. NGL
protects against the corrosive effect of these gases to compressor components
while maintaining lubricating properties.
Physical Properties
PRODUCT NGL-444 NGL-555 NGL-777 NGL-888
ISO Grade - 100 150 220
Viscosity:
@ 40°C, cSt 79 105 150 209
@ 100°C, cSt 16.0 20.5 28.8 38.5
@ 100°F, SUS 397 113 753 1052
@ 210°F, SUS 83.5 21.0 140.0 185.0
Viscosity Index 218 222 233 236
Pour Point, °F (°C) -55(-48) -56(-49) -44(-42) -44(-42)
Flash Point, °F (°C) 450 (232) 505 (263) 500 (261) 515 (268)
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
NGP 220 Natural Gas Compressor
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of August 11, 2010.
When a synthetic oil is not needed, Summit’s NGP 220 of highly refined petroleum
based lubricants are formulated to provide some of the same benefits provided by
hydrocarbon based synthetics such as PAO and PIB. The additive technology used
in the NGP Series enable them to far outperform other mineral oil based lubricants.
Some of the benefits are:
• The high viscosity index (V.I.) of NGP 220 is comparable to a synthetic PAO and
means a significant increase in operating temperature range over most mineral
based oils. It also means a lower viscosity grade NGP 220 product may be used
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
in place of a higher viscosity mineral oil with a lower viscosity index. This can
mean lower temperature flow limits and may eliminate the need for heated, pres
surized day tanks and heat traced lines. It can also mean better lubricant film
strength at higher cylinder and packing temperatures on reciprocating compressors.
• The pour point of the NGP 220 approaches that of a synthetic PAO and may be as
much as 25 ºF lower than some mineral based oils. The lower limit may eliminate no
flow shutdowns on cold days or the need for special tank and line heaters.
• NGP 220 is made from highly purified petroleum oils that only contain trace
amounts of sulfur and other impurities found in group I mineral oils. Impurities
common to many mineral oil base stocks can react with components of the gas
stream to form by-products harmful to the compressor system.
• NGP 220 is formulated to inhibit against the corrosive effects of wet CO2 and
August 11, 2010
Physical Properties
PRODUCTS NGP-220
ISO Viscosity Grade 220
Viscosity:
@ 40°C, cSt 216
@ 100°C, cSt 27.1
@ 100°F, SUS 1114
@ 210°F, SUS 133
Viscosity Index 160
Specific Gravity 0.873
Density
@ 60°F, g/mL 0.872
@ 185°F, g/mL 0.821
Pour Point, °F (ºC) -22(-30)
Flash Point, °F (ºC) 470(243)
Four Ball Wear Test, mm 0.52
Thermal Characteristics:
Specific Heat Thermal Conductivity
BTU/lbm - °F BTU/hr - ft 2 and °F/inch
140°F = 0.476 0°F = 0.94
160°F = 0.485 200°F = 0.88
180°F = 0.494 400°F = 0.83
SYNTHETIC BLEND
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
NGP SERIES Natural Gas Compressor
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of August 6, 2010.
When a synthetic oil is not needed, Summit’s NGP Series of highly refined petroleum
based lubricants are formulated to provide some of the same benefits provided by
hydrocarbon based synthetics such as PAO and PIB. The additive technology used
in the NGP Series enable them to far outperform other mineral oil based lubricants.
Some of the benefits are:
• The high viscosity index (V.I.) of NGP is comparable to a synthetic PAO and means
a significant increase in operating temperature range over most mineral based
oils. It also means a lower viscosity grade NGP product may be used in place of
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
a higher viscosity mineral oil with a lower viscosity index. This can mean lower
temperature flow limits and may eliminate the need for heated, pressurized day
tanks and heat traced lines. It can also mean better lubricant film strength at higher
cylinder and packing temperatures on reciprocating compressors.
• The pour point of the NGP Series approaches that of a synthetic PAO and may be
as much as 25 ºF lower than some mineral based oils. The lower limit may eliminate
no flow shutdowns on cold days or the need for special tank and line heaters.
• NGP is made from highly purified petroleum oils that only contain trace amounts
of sulfur and other impurities found in group I mineral oils. Impurities common to
many mineral oil base stocks can react with components of the gas stream to form
by-products harmful to the compressor system.
• NGP Series is formulated to inhibit against the corrosive effects of wet CO2 and
August 6, 2010
Physical Properties
PRODUCTS NGP-32 NGP-68 NGP-100 NGP-150
ISO Viscosity Grade 32 68 100 150
Viscosity:
@ 40°C, cSt 32 67 95 150
@ 100°C, cSt 5.4 10 13.1 18.6
@ 100°F, SUS 165 343 488 774
@ 210°F, SUS 44 61 72 95
Density
@ 60°F, g/mL 0.867 0.868 0.871 0.872
@ 185°F, g/mL 0.823 0.824 0.827 0.831
Thermal Characteristics:
Specific Heat Thermal Conductivity
BTU/lbm - °F BTU/hr - ft 2 and °F/inch
140°F = 0.476 0°F = 0.94
160°F = 0.485 200°F = 0.88
180°F = 0.494 400°F = 0.83
SYNTHETIC NATURAL GAS COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
NGSH SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of June 21, 2007.
The Summit NGSH Series of lubricants is formulated from
the highest quality synthetic hydrocarbon base stocks.
NGSH lubricants are extended life fluids with special
additives to protect equipment from wear, rust and hydro-
gen sulfide corrosion. These fluids are designed for rotary
screw and reciprocating compressors in natural gas serv-
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
June 21, 2007
Viscosity
@ 40°C, cSt 62.7 95.5 140.5 192.0
@ 100°C, cSt 10.10 13.9 18.50 22.40
@ 100°F, SUS 320 491 718 990
@ 210°F, SUS 60.4 75.2 94.3 111.4
Pour Point, °F (°C) -55 (-48) -44 (-42) -49 (-45) -49 (-45)
Flash Point, °F (°C) 475 (246) 500 (260) 515 (268) 525 (274)
Autoignition, °F (°C) 750 (399) 760 (404) 760 (404) 765 (407)
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
PGI SERIES
Summit PGI synthetic lubricants were designed for use in
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current .
the compression of propane in refrigeration or unloading
service. Available in three grades for rotary screw and
reciprocating compressors, PGI is especially suitable for
wet gas situations. Due to the varying make-up of gases
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS PGI-68 PGI-100 PGI-150
February 21, 2012
Viscosity
@ 40°C, cSt 69 102 156
@ 100°C, cSt 12.7 18.0 26.2
@ 100°F, SUS 349 519 788
@ 210°F, SUS 70.2 92.2 128.1
Thermal Characteristics:
Specific Heat Thermal Conductivity
Cal/g-ºC BTU/Hr/(Ft ºF)
60ºC = 0.48 100ºF = 0.095
80ºC = 0.49 200ºF = 0.090
100ºC = 0.51
SYNTHETIC NATURAL GAS COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
PGS-2 & PGS-3
Product Data Sheet Summit PGS-2 & PGS-3 synthetic lubricants are polyglycol-based
products for use in rotary screw gas compressors requiring the
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
highest level of resistance to hydrocarbon dilution. Extreme conditions
demand the unique properties of these fluids. These products when
compared to petroleum-based lubricants provide better wear
protection, reduced sludge and reduced deposit formation to ensure
enhanced performance.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
oils, care should be taken to make sure they are not mixed.
Physical Properties
PRODUCTS PGS-2 PGS-3
Viscosity
@ 40°C, cSt 89.5 114
@ 100°C, cSt 11.70 17.4
@ 100°F, SUS 460 584
@ 210°F, SUS 66.0 89.4
Applications:
• Natural Gas Compressors • Process Gas Compressors
SYNTHETIC NATURAL GAS COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
PGS SERIES
Physical Properties
March 24, 2009
Thermal Characteristics:
Specific Heat Thermal Conductivity
Cal/g-ºC BTU/Hr/(Ft ºF)
60ºC = 0.48 100ºF = 0.095
80ºC = 0.49 200ºF = 0.090
100ºC = 0.51
PREMIUM SYNTHETIC BLEND
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
PS SERIES
Product Data Sheet
Air Compressor
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of January 19, 2010.
Summit PS Series premium synthetic blend lubricants are
a blend of synthetic and petroleum base fluids specially
designed for compressor applications and are useful in
multi-purpose applications. The lighter grades are also
well suited for gas and steam turbine applications. The PS
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
July 15. 2013
Viscosity
@ 40ºC, cSt 29.6 45.8 63.6 97.1 145.1
@ 100ºC, cSt 5.12 6.68 8.31 10.97 14.31
@ 100ºF, SUS 153 237 329 505 760
@ 210ºF, SUS 43.4 48.6 54.2 63.7 76.7
Page 1 of 2
Summit PS SERIES Air Compressor
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
PSV-22
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of June 21, 2007.
Summit PSV-22 is formulated from a vacuum distilled
ultra-pure paraffinic hydrocarbon base stock to provide an
extremely low vapor pressure vacuum pump lubricant. This
non-foaming fluid has excellent water separation and pro-
vides protection against wear, rust and corrosion. PSV-22
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCT PSV-22
ISO Grade 22
Viscosity
@ 40°C, cSt 20.9
@ 100°C, cSt 4.19
@ 100°F, SUS 109.6
@ 210°F, SUS 40.4
Copper Corrosion 1A
SYNTHETIC REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RAB SERIES
Product Data Sheet Summit RAB Series refrigeration oils are alkylate based
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
and formulated for use in reciprocating, rotary, and
centrifugal refrigeration compressors using ammonia, R12,
R22, R114 and R502. These products are extremely stable
at high compression temperatures while providing excellent
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
August 2, 2012
Viscosity,
@ 40°C, cSt 33 55
@ 100°F, SUS 150 288
Dielectric Strength,KV 40 40
Water, ppm 30 30
NSF Registered H2 H2
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RHB SERIES
Product Data Sheet The RHB Series is formulated from an AB-Alkylbenzene synthetic blend and designed to
function under the stringent requirements of CFCs-Chlorofluorocarbon, HCFCs-
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current .
Hydrochlorofluorocarbon refrigerants like R11, R12, R13, R22, R113, R114, R123, R124,
R401a, R401b, R402a, R402b, R403b, R406a, R408a, R409a, R500, R502, R503; & R717
(NH3 aka ammonia) DX and liquid overfeed industrial refrigeration systems. Besides its
inherent inertness, improved system efficiency and higher productivity, the performance
advantages of the RHB Series versus naphthenic oils include:
(1) Partial miscibility and solubility with CFCs, HCFCs and ammonia for improved
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
with naphthenic and paraffinic mineral oils, as well as PAO and AB synthetic oils, which
allows top-off over these other oils and eliminates the need for system flushes
and excessive evaporator maintenance. As with all specialty lubricants, indoor storage
and immediate closing of original containers after use is strongly recommended
to avoid particulate and moisture contamination.
Physical Properties
PRODUCTS RHB-32 RHB-46 RHB-68 RHB-100
Viscosity Index 99 88 93 86
NSF Registered H2 H2 H2 H2
REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RHT FG-68
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
food service industry. Besides providing value added benefits in the
areas of improved system efficiency and higher productivity, the
performance advantages of Summit RHT FG-68 versus naphthenic
oils include:
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS RHT FG-68
ISO Grade 68
Viscosity
@ 40ºC, cSt 67.97
@ 100ºC, cSt 8.66
Viscosity Index 98
Specific Gravity, 60ºF 0.8760
Density, lb/gal @ 60ºF 7.2953
Pour Point, ºF (ºC) -42 (-41)
Flash Point, ºF (ºC) 470 (243)
Fire Point, ºF (ºC) 505 (263)
NSF Registered H1
Kosher Approved Yes
Halal Certified Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture,
after which the product should be recertified prior to use.
REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RHT Series
Product Data Sheet Summit RHT Series Performance Plus oils are a highly refined,
hydrotreated ammonia compressor lubricants, specially designed
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
to function under the stringent requirements of closed-loop
ammonia refrigeration systems. Besides providing value-
added benefits in the areas of i m p ro v e d s y s t e m e f f i c i e n c y
a n d h i g h e r p ro d u c t i v i t y, the performance advantages of
Summit RHT Series oils versus naphthenic oils include:
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS RHT-32 RHT-46 RHT-68 RHT-100
ISO Grade 32 46 68 100
Viscosity
@ 40°C, cSt 31.18 42.55 70 100.94
@ 100°C, cSt 5.32 6.44 8.8 11.26
NSF Registered H2 H2 H2 H2
SYNTHETIC REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RPA SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
and centrifugal refrigeration compressor applications using
any of several refrigerants including ammonia (R717),
R12, R13, R22, R113, R114, R123, R401A, R401B, R402B,
R409A, R500, R502 and R503.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS RPA-32 RPA-46 RPA-68 RPA-100
ISO Grade 32 46 68 100
Viscosity
@ 0ºC, cSt 314 497 887 1776
@ 40ºC, cSt 31.3 43.6 61.8 91.5
@ 100ºC, cSt 5.45 6.47 8.89 10.48
NSF Registered H2 H2 H2 H2
SYNTHETIC REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
RPE SERIES
Product Data Sheet Summit's RPE Series is fully synthetic lubricants designed for
use in refrigeration compressors using R-134A and other
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
HFCs as the refrigerant. They have excellent chemical and
thermal stability as well as superior lubricity characteristics
with steel and aluminum. They are miscible with all HFCs,
HCFCs, CFCs and blends. They were specifically
developed for HFC refrigerants.
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS RPE-32 RPE-46 RPE-68 RPE-100 RPE-170
January 17, 2013
Viscosity
@ 40ºC, cSt 33 45.1 68.5 98.4 171.53
@ 100ºC, cSt 5.8 7.22 9.5 12.3 16.49
Flash Point,
ºF (ºC) 471(244) 493(256) 520(271) 514(268) 585(307)
Fire Point,
ºF (ºC) 511(266) 530(276) 565(296) 550(287) 630(332)
Pour Point,
ºF (ºC) -58(-50) -31(-35) -35(-37) -15(-26) -27(-33)
SYNTHETIC REFRIGERATION COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
R SERIES
Product Data Sheet Summit R Series synthetic hydrocarbon refrigeration lubri-
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
cants are designed to function under severe service conditions.
These fluids have a very high viscosity index, contain no paraffin
and are compatible with various fluorinated refrigerants,
ammonia, methyl chloride and carbon dioxide. The Summit R
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
May 13, 2011
Viscosity
@ 40°C, cSt 31.0 45.8 63.3 95
@ 100°C, cSt 5.9 7.80 10.0 13.9
Pour Point, °F (ºC) -87 (-66) -78 (-61) -54 (-48) -60 (-51)
Flash Point, °F (ºC) 485 (252) 510 (266) 525 (274) 540 (282)
Fire Point, °F (ºC) 520 (271) 530 (277) 540 (282) 555 (291)
NSF Registered H1 H1 H1 H1
ISO 21469 Yes Yes Yes Yes
Kosher Yes Yes Yes Yes
Halal Yes Yes Yes Yes
CFIA Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC BLOWER LUBRICANTS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SBL FOOD GRADE SERIES
Product Data Sheet Summit SBL Food Grade Series synthetic lubricants are formu-
lated to provide maximum lubrication protection and service for all
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
positive displacement blowers including Roots, Gardner-Denver,
Sutorbilt and Duroflow. Advantages over petroleum lubricants
include extended lubricant life (up to 4,000 hours with oil analysis),
reduced operating temperatures, better corrosion protection,
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SBL Food Grade SBL-100F SBL-150F SBL-220F SBL-320F
ISO Grade 100 150 220 320
Viscosity
@ 40°C, cSt 99.3 150 213 320
@ 100°C, cSt 13.9 19.1 26.4 33
@ 100°F, SUS 510 773 1098 1658
@ 210°F, SUS 74.9 96.9 130 161
Viscosity Index 141 145 158 144
Specific Gravity 0.841 0.845 0.848 0.851
Flash Point, °F (°C) 515 (268) 515 (268) 520 (271) 520 (271)
Pour Point, °F (°C) -60 (-51) -49 (-45) -40 (-40) -30 (-34)
Copper Corrosion 1A 1A 1A 1A
NSF Registered H1 H1 H1 H1
ISO 21469 Yes Yes Yes Yes
Kosher Approved Yes Yes Yes Yes
Hala Certified Yes Yes Yes Yes
CFIA Accepted Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC BLOWER LUBRICANTS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SBL SERIES
Product Data Sheet Summit SBL synthetic lubricants are formulated to provide
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
maximum lubrication protection and service for all positive
displacement blowers including Roots, Gardner-Denver,
Sutorbilt and Duroflow. Advantages over petroleum lubri-
cants include extended lubricant life (up to 8,000 hours with
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS SBL-100 SBL-150 SBL-220 SBL-320
Viscosity
@ 40°C, cSt 91.8 142.7 206.2 302.6
@ 100°C, cSt 13.1 18.0 23.4 31.0
@ 100°F, SUS 470 750 1086 1619
@ 210°F, SUS 71.9 91 116 150
Flash Point, °F (°C) 475 (246) 475 (246) 475 (246) 485 (252)
Pour Point, °F (°C) -60 (-51) -60 (-51) -45 (-43) -40 (-40)
Copper Corrosion 1A 1A 1A 1A
NSF Registered - - - H2
SEAMER GEAR OIL
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SEAMER OIL-150P
Product Data Sheet Seamer Oil-150P is specially formulated to lubricate the gear systems found
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
in “once through” designed can closers used in food canning operations. This
machine design allows the oil to cascade through the gears, lubricating as it
goes, until it is discharged into the sanitary drain system from the bottom of
the machine . Seamer Oil-150P is blended using the highest quality base
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
stocks and utilizes an additive package that provides excellent wear, EP, and
corrosion properties. This superior formulation passes all 12 stages of the
FZG Gear Test. Tested extensively, Seamer Oil-150P has demonstrated
exceptional results when used in this application.
Physical Properties
SEAMER OIL 150P
ISO Grade 150
Viscosity
@ 40°C, cSt 146
@ 100°C, cSt 14.5
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SEAMER GEAR OIL
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SEAMER OIL 150 S
Product Data Sheet Summit Seamer Oil 150 S is designed to lubricate can seaming equipment
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
which reclaims the used oil. This specialized application requires a
product that protects the gearing and other moving parts of the machine.
The lubricant must also suspend contaminants for filtering and removal
of water. Fortified with oxidation inhibitors, corrosion inhibitors and
antiwear additives, Seamer Oil 150 S protects the moving parts of the
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
machine. In addition, this formula holds water, juice, syrups and other
contaminants in suspension allowing for easy removal.
Physical Properties
SEAMER OIL 150 S
ISO Grade 150
Viscosity
@ 40°C, cSt 154.71
@ 100°C, cSt 19.20
Viscosity Index 142
Specific Gravity 0.8534
Density, lbs/gal (60°F) 7.0303
Flash Point, °F (°C) 515 (268)
Fire Point, °F (°C) 575 (302)
Pour Point, °F (°C) -49 (-45)
Four Ball Wear Test, mm .32 avg.
Rust Pass
Copper Corrosion 1A
NSF Registration H1 Pending
Kosher Approved Pending
Halal Certified Pending
CFIA Accepted Pending
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC GAS TURBINE OILS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
SH®-32T AND SH®-46T
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
Summit SH®-32T and SH®-46T gas turbine lubricants have been
formulated to operate in land-based gas turbines under a wide
range of temperatures. Synthetic hydrocarbon base stocks and
selected additives combine to provide excellent viscosity-tem-
perature characteristics, oxidation stability, wear resistance, and
load-carrying ability.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS SH®-32T SH®-46T
46
Approximate ISO Grade 32
Viscosity
@ 40°C, cSt 29.7 42.0
@ 100°C, cSt 5.66 7.5
Viscosity Index 133 146
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SH ® SERIES
Product Data Sheet Summit SH® Series lubricants are manufactured from the
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
highest quality PAO (polyalphaolefin) base stocks and
advanced additive technology. SH® Series lubricants are
recommended for rotary screw, centrifugal, vane and
reciprocating compressors and offer many advantages over
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS SH®-32 SH®-46 SH®-68 SH®-100 SH®-150
Viscosity:
@ 40°C, cSt 32.0 43.2 66.0 93.0 142
@ 100°C, cSt 5.80 7.34 9.80 12.5 16.3
@ 100°F, SUS 163 220 339 482 737
@ 210°F, SUS 45.7 50.4 59.6 69.8 85.1
Autoignition
Temp., °F (°C) 730 (388) 745 (396) 745 (396) 760 (404) 760 (404)
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SHV SERIES
Physical Properties
PRODUCTS SHV-15 SHV-22 SHV-32 SHV-46 SHV-68 SHV-100
ISO Grade 15 22 32 46 68 100
August 11, 2010
Viscosity
@ 40°C, cSt 15.2 21.2 29.9 43.2 63.7 93.0
@ 100°C, cSt 3.54 4.51 5.70 7.31 9.60 12.5
@ 100°F, SUS 83.2 110 154 221 327 482
@ 210°F, SUS 38.2 41.4 45.3 50.7 58.7 69.8
Autoignition
Point °F 710 720 730 740 745 760
(ºC) (377) (382) (387) (393) (396) (404)
Copper Strip
Corrosion 1A 1A 1A 1A 1A 1A
Vapor
Pressure, mm Hg.
(Modified ARS 184-R1)
100ºF <0.00047 <0.00040 <0.00030 <0.00020 <0.00010 <0.00004
200ºF <0.00101 <0.00080 <0.00062 <0.00056 <0.00050 <0.00018
300ºF <0.00190 <0.00170 <0.00160 <0.00145 <0.00130 <0.00085
The Summit SHV Series are compatible with commonly used seal and
gasket materials in vacuum pump service.
SYNTHETIC REFRIGERATION COMPRESSOR
SRO SERIES
Product Data Sheet GENERAL DESCRIPTION
The Summit SRO Series was developed to overcome many of
the shortcomings of most POE-based formulations which include
hygroscopicity, lack of wear protection, viscosity dilution and
chemical instability in the presence of moisture. The SRO Series
is a full synthetic formulation based on POE-Polyolester base
oils for optimum mutual solubility and oil return assurances.
The SRO Series is formulated for environmentally friendlier
refrigerant gases including HFCs like R134a, among others, in
industrial and commercial refrigeration, air conditioning and
chiller applications. To minimize additive compatibility issues,
the SRO Series should not be mixed with more than 5% of the
previous POE oil. SRO Series is not designed for ammonia
refrigeration due to its reactivity with R717. It is compatible
with all paints, plastics and elastomers used in this application.
As with all specialty lubricants, indoor storage in original
containers and immediate closing of same after dispensing should
minimize moisture and particulate contamination. When in
doubt as to the suitability for your particular application,
please consult the factory or your local Summit distributor.
Page 1 of 2
June 18, 2013
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SRO Series 10 22 32 46 68 100 120 150 170 220
Viscosity
@ 40ºC, cSt 10.0 21.8 32.6 45.5 66.8 101.5 120.8 150.3 170.3 218.7
@ 100ºC, cSt 2.69 4.5 6.0 7.5 9.9 13.7 15.6 18.3 19.6 23.6
Viscosity Index 106 122 130 130 131 136 135 136 133 134
Flash Point,
SRO SERIES
ºF 370 470 500 530 520 540 525 545 530 550
ºC 188 243 260 277 271 282 274 285 277 288
Fire Point,
ºF 390 510 530 560 565 580 580 580 590 590
ºC 199 266 277 293 296 304 304 304 310 310
Pour Point,
ºF -105 -85 -71 -71 -65 -54 -56 -49 -44 -40
ºC - 76 -65 -57 -57 -54 -48 -49 -45 -42 -40
Specific Gravity
SYNTHETIC REFRIGERATION COMPRESSOR
@ 60ºF 0.8503 0.8628 0.8732 0.8709 0.8744 0.8783 0.8798 0.8817 0.8783 0.8804
Page 2 of 2
SYNTHETIC AIR COMPRESSOR
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SUMMIT SIERRA® SERIES
Produced from the highest grade additives and base stocks available, Summit
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Sierra Series® will continue to protect air compressors from wear and deposit
formation where other compressor lubricants fail. Based on lubrication
technology with millions of hours of proven performance, Summit Sierra® is
supported by the Summit performance guarantee. Utilizing the free in-house
lubrication analysis provided by Summit, professional lab technicians can
track the performance of the lubricant and will determine when the lubricant
needs to be changed. Summit Sierra® is compatible with most rotary screw air
compressor lubricants on the market. It is not compatible with silicone or
October 25, 2010
Physical Properties
PRODUCT SIERRA-32 SIERRA-46 SIERRA-68
ISO Grade 32 46 68
Density (lbs/gal)
@ 60ºF 7.23 7.26 7.29
Pour Point -51ºC -48ºC -45ºC
Flash Point 455ºF 475ºF 510ºF
Fire Point 475ºF 505ºF 540ºF
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SumTech® AQ-320
corrosion inhibitors extend the excellent anti-corrosion nature inherent of the thicken-
er. SumTech® AQ-320 is the grease of choice for marine, pulp and paper, and steel
mill industries where exposure to water and aggressive media cannot be avoided.
SumTech® AQ-320 is also suitable for use in sealing water valves, labyrinth seals,
and rotary steam unions.
SumTech® AQ-320
NLGI Grade 2
Color beige, light brown
Texture homogeneous
October 23, 2006
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SumTech® EMB-160
range of -22ºF to 320ºF and high speed factor of 500,000 nDm makes SumTech®
EMB-160 the ideal lubricating grease for electric motor bearings designed to be
lubricated for life.
SumTech® EMB-160
NLGI Grade 2
Color beige
October 23, 2006
Texture homogenous
Base Oil synthetic hydrocarbon/mineral oil
Base Oil Properties - ASTM D 446
Viscosity at 40ºC cSt 160
Viscosity at 100ºC cSt 18
Viscosity Index 125
Thickener Type polyurea
Density at 20ºC (g/cm³) 0.9
Service Temperature -22ºF to 320ºF
Drop Point - ASTM D 2265 >250ºC(482ºF)
Penetration - ASTM D 217
Worked 60 ds 265-295
Oil Separation - ASTM D 6184 <5
4-Ball Wear - ASTM D 2266 0.50 mm, 0.54 mm
Weld load 160 kg
Corrosion Preventative Properties -
ASTM D 1743 pass
Corrosion Preventative Properties,
EMCOR - ASTM D 6138 1
Copper Corrosion - ASTM D 4048 1a
ALUMINUM COMPLEX THICKENED SEMI-SYNTHETIC
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SumTech® FMG Series
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
aluminum complex thickener system provides excellent water resistance and a broad
operating temperature range. A combination of newly developed additives and dependable
HX1 additives provide excellent anti-wear/extreme pressure properties, oxidation resistance,
and corrosion prevention. Special additives are employed to keep the grease in place
between wash-down cycles which improves equipment and lubricant life in wet conditions.
SUMTECH® FMG grease is NSF Registered and meets USDA 1998 (H1) guidelines
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SumTech® FMG-1 FMG-2
April 23, 2013
NLGI Grade 1 2
Color Off White to Yellow Off White to Yellow
Texture Homogenous Homogenous
Base Oil Mineral Oil/PAO Mineral Oil/PAO
Base Oil Properties
Viscosity @ 40°C cSt 138 cSt 138 cSt
Viscosity @ 100°C cSt 17.5 cSt 17.5 cSt
Viscosity Index 140 140
Thickener Type Aluminum Complex Aluminum Complex
Density at 20°C (g/cm) .95 .97
Service Temperature Range -35°C to 148°C (300°F) -30°C to 148°C (300°F)
Drop Point 250°C (482°F) 270°C (518°F)
Penetration
Worked 60 dbl strokes 320 280
100,000 dbl strokes 350 308
Oil Separation Less than 7% Less than 3%
4-Ball Wear ASTM D2266 0.45 mm 0.47 mm
4-Ball Load Wear Index 48.9 64.3
Last non-seizure Load 100 kg 100 kg
Weld Load 315 kg 400 kg
Corrosion Preventative Properties
ASTM D 1743 Pass Pass
Corrosion Preventative Properties
EMCOR – ASTM D 6138 0.0 0.0
Water Washout – ASTM D 1264 9% 3%
NSF Registered H1 H1
Kosher Approved Yes Yes
CFIA Accepted Pending Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC BASED LUBRICATING GREASE
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SumTech® SG Series
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
thickener and synthetic hydrocarbon base oil are proven components for high
temperature operation. Special anti-oxidant blended additives provide oxidation
stability at both low and high temperatures. Synergistic corrosion inhibitors offer
protection for both ferrous and yellow metals which are commonly used in today's
rolling element bearings.
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Corrosion Preventative
Properties - ASTM D 1743 Pass Pass Pass
Corrosion Preventative
Properties EMCOR 0/0 0/0 0/0
ASTM D 6138
Copper Corrosion 1b 1b 1b
ASTM D 4048
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Viscosity
PRODUCT
@ 40°C, cSt
@ 100°C, cSt
Viscosity Index
Density, lbs/gal
@ 210°F, SUS
@ 100°F, SUS
Specific Gravity
Physical Properties
5.4
141
136
44.2
26.5
7.989
SYNTHETIC AIR COMPRESSOR
0.9593
-69 (-56)
485 (252)
SUPRA-26N
Summit Supra-26N has been formulated to address the
specific problems associated with centrifugal compressor
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SUPRA- 32
Physical Properties
PRODUCT SUPRA-32
November 4, 2010
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SUPRA COOLANT®
Physical Properties
PRODUCT SUPRA COOLANT-
June 21, 2007
Viscosity
@ 40°C, cSt 54.9
@ 100°C, cSt 9.32
@ 100°F, SUS 279
@ 210°F, SUS 57.7
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SYNGARD SERIES
lubricant consumption.
•Moisture in the compressed air is emulsified to protect metal surfaces
and prevent rust.
•Enhanced extreme pressure properties protect tools from seizure and wear
and provide good adherence to wet working surfaces.
•Elimination of lubricant oxidation prevents lost time due to gumming and
varnishing.
•Proper atomization for good lubrication and control of fogging.
•Extremely good low temperature properties to protect equipment in
adverse weather conditions.
Physical Properties
PRODUCTS SYNGARD-32 SYNGARD-68
ISO Grade 32 68
Viscosity
@ 40ºC, cSt 30.6 66.6
@ 100ºC, cSt 5.80 9.78
@ 100ºF, SUS 157 342
@ 210ºF, SUS 45.6 59.4
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SYNGEAR® FG SERIES
Physical Properties
®
SYNGEAR FG-150 FG-220 FG-320 FG-460 FG-680
August 2, 2011
NSF Registered H1 H1 H1 H1 H1
ISO 21469 Yes Yes Yes Yes Yes
Kosher Approved Yes Yes Yes Yes Yes
Halal Certified Yes Yes Yes Yes Yes
CFIA Accepted Yes Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC GEARS / HEAVY DUTY
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SYNGEAR®
Product Data Sheet Heavy Duty Series
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
Most industries in today's world are shifting their focus
toward efficiency improvements by putting an emphasis on
reducing energy requirements for equipment used in plant
operations and for vehicular equipment. Technological
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SYNGEAR® 75W-90 75W-140 80W-140
Viscosity
@ 40°C, cSt 157 183.92 283
@ 100°C, cSt 17.8 26.08 31.9
@ 100°F, SUS 727 940.89 1470
@ 210°F, SUS 89 128.09 156
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
SYNGEAR®
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of August 19, 2010.
Food Grade PG SERIES
Summit Syngear® Food Grade PG Series synthetic lubricants are
polyglycol-based products for use in enclosed gear, bearings, and
compressors where conditions demand the unique properties of
these fluids. Use these lubricants where there is the potential for
incidental contact with food or food packaging. Better wear protec-
tion, thermal and oxidation stability, and reduced sludge and
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
®
SYNGEAR PG-150F PG-220F PG-320F PG-460F PG-680F
ISO Grade 150 220 320 460 680
Viscosity
@ 40°C, cSt 143 224 319 442 650.3
@ 100°C, cSt 27.2 41.3 57.0 78.1 110.6
@ 100°F, SUS 718 1135 1607 2224 3290
@ 210°F, SUS 133 199 273 374 530
Flash Point , °F (°C) 525 (270) 505 (263) 510 (266) 515 (268) 525 (274)
Pour Point, °F (°C) -49 (-45) -49 (-45) -44(-42) -44(-42) -44(-42)
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
SYNTHETIC GEARS / BEARINGS
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
SYNGEAR® PG SERIES
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of December 15, 2010.
Summit Syngear ® PG Series synthetic lubricants are
polyglycol-based products for use in enclosed gear,
bearings, and compressors where conditions demand the
unique properties of these fluids. Better wear protection,
thermal and oxidation stability, and reduced sludge and
deposit formation insure enhanced performance when
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
December 15, 2010
Viscosity
@ 40°C, cSt 237 314 441 654 1000
@ 100°C, cSt 42.9 55.7 76.6 111 162.0
@ 100°F, SUS 1191 1580 2224 3312 5072
@ 210°F, SUS 206 266 366 532 774
Flash Point , °F (°C) 510 (266) 520 (271) 530 (277) 525 (274) 525 (274)
Pour Point, °F (°C) -49 (-45) -49 (-45) -44(-42) -44(-42) -44(-42)
Thermal Characteristics:
Specific Heat Thermal Conductivity
Cal/g-ºC BTU/Hr/(Ft ºF)
60ºC = 0.48 100ºF = 0.095
80ºC = 0.49 200ºF = 0.090
100ºC = 0.51
SYNTHETIC GEARS / HEAVY DUTY
APPLICATION
Summit Syngear® SH®-1000 Series gear lubricants are recommended for use in
all types of enclosed gearing as well as plain and rolling element bearings.
These lubricants are ideal for heavily loaded low speed gears and bearings
where boundary or elasto-hydrodynamic lubrication (EHL) conditions exist,
such as in mine hoist gear reducers. They are particularly recommended for
gearboxes which operate under excessively high temperatures where good quality
conventional oils rapidly oxidize. Summit Syngear® SH®-1000 Series gear lubricants
may also be used in certain open gear applications, but it is recommended that
Summit lubrication engineers be consulted to select the most effective method
of application. Summit Syngear SH®-10032, SH®-10046 and SH®-10068 are also
recommended or use in piston or gear-type pumps, expecially where pressures
exceed 1000 psi or when operating over a wide temperature range.
Summit Syngear® SH®-1000 Series gear lubricants are compatible with most
seal materials, paints and plastics, including nitrile Buna N, neoprene, viton,
teflon, polyethylene, polyurethane ether, fluorocarbon, polyacrylate,
polysulfide, ethylene acrylic, epoxy, plastisol, PVC, acrylic paint and lacquer.
Page 1 of 2
July 15, 2013
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SYNGEAR® SH®-10032 SH®-10046 SH®-10068 SH®-1010 SH®-1015 SH®-1022 SH®-1032 SH®-1046 SH®-1068 SH®-1100 SH®-1150
ISO Grade 32 46 68 100 150 220 320 460 680 1000 1500
AGMA Number -- - 2 EP 3 EP 4 EP 5 EP 6 EP 7 EP 8 EP 8 EP 9 EP
Viscosity
@ 40°C, cSt 31.0 42.9 67.1 95.7 147 232 342 490 700 947 1513
@ 100°C, cSt 5.8 7.4 9.9 12.9 17.8 25.4 32.8 43.1 54.2 66.2 95.8
Viscosity Index 132 137 130 132 133 139 134 139 134 135 143
Specific Gravity 0.849 0.851 0.859 0.862 0.868 0.877 0.878 0.882 0.892 0.890 0.892
Pour Pt. F°(C°) -58 (-50) -40 (-40) -44 (-42) -42 (-41) -49 (-45) -45(-43) -40(-40) -35(-37) -30(-34) -20(-28) -17(-27)
Flash Pt. F°(C°) 470 (243) 475 (246) 480 (249) 485(252) 485(252) 485(252) 485(252) 485(252) 485(252) 485(252) 490(254)
Copper Corrosion 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A 1A
Rust Test Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass
Four-Ball Weld, kgs 200 200 200 200 315 315 315 315 315 400 400
Four-Ball Scar, mm .50 .40 .30 .30 .39 .34 .30 .30 .30 .30 .30
FZG Gear Test 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+ 12+
Page 2 of 2
Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass
SYNGEAR® SH®-1000 SERIES
SYNTHETIC GEARS / BEARINGS
APPLICATION
Summit Syngear ® SH ®-7000 Series lubricants are recommended
for use under severe high or low temperature conditions when lubricating
industrial enclosed gears and heavily loaded plain or rolling element
bearings. They are particularly recommended for applications where
high oil temperatures result in short oil life or high maintenance costs.
Summit Syngear® SH®-7032, SH®-7046 and SH®-7068 may be used in
piston or gear type pumps, expecially where pressures exceed 1000
psi or when operating over a wide temperature range. Use Summit
Syngear® SH®-7032 through Syngear® SH®-71000 for applications
where the corrosion of yellow metals is a concern, as these lubricants do
not contain additives which tend to attack metals such as brass, bronze or
copper.
The Summit Syngear® SH®-7000 Series lubricants are compatible with
essentially all seal materials, plastics and paints, including nitrile Buna N,
neoprene, viton, teflon, polyethylene, polyurethane ether, fluorocarbon,
polyacrylate, polysulfate, ethylene acrylic, epoxy, plastisol, PVC,
acrylic paint and lacquer.
Page 1 of 2
July 15, 2013
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
SYNGEAR® SH®-7032 SH®-7046 SH®-7068 SH®-7100 SH®-7150 SH®-7220 SH®-7320 SH®-7460 SH®-7680 SH®-71000
Rust Test Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass
FZG Gear Test 11 11 11 11 11 11 11 11 11 11
Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass
SYNGEAR® SH ®-7000 SERIES
SYNTHETIC GEARS / HEAVY DUTY
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SYNGEAR® WT Series
Product Data Sheet Summit Syngear® WT Series lubricants are fully synthetic high
performance gear oils enhanced with new generation anti-micropitting
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
additives. The PAO base oil has outstanding oxidation and thermal
stability, naturally high viscosity index and excellent low temperature
pumpability and fluidity. The additive system not only minimizes scuffing
wear, but offers a high level of resistance to micropitting fatigue. High
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
load carrying capability and low sludge formation make these superior
lubricants a choice for many industrial applications. Syngear® WT
Series provides maximum protection against rust, corrosion, and foaming.
APPLICATION
Summit Syngear® WT Series are recommended for highly loaded
enclosed gearing as well as plain and rolling element bearings. These
shear stable lubricants resists damage to gear teeth caused by repeated
shock loads. Syngear® WT Series lubricants are ideal for wind turbine
August 2, 2011
Physical Properties
SYNGEAR® WT-100 WT-150 WT-220 WT-320
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
SYNTENAL CD-50 EQ
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of May 13, 2002.
Summit Syntenal CD-50 EQ is a fully synthetic manual
transmission lubricant for year-round use in off-and-on
highway equipment. Syntenal CD-50 EQ is suitable for
transmissions and gear cases where API GL-1 through
GL-3 gear protection is required. It also has a very low
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
May 26, 2004
PRODUCT CD-50 EQ
SAE Grade 50
Specific Gravity 0.8660
Flash Point, °F (°C) 465 (240)
Pour Point, °F(°C) -40 (-40)
Viscosity
@ 40°C, cSt 155
@ 100°C, cSt 19.8
@ 100°F, SUS 802
@ 210°F, SUS 100
Foaming Tendency
Seq I 0/0
Seq II 0/0
Seq III 0/0
Customer Benefits
Superior lubrication at all temperatures
Longer gear life
Increased fuel economy
HEAT TRANSFER FLUID
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
THERMOYLE - 46P
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of January 27, 2011.
Summit Thermoyle-46P Performance Plus oil was designed to
meet the tough thermal demands placed on high temperature heat
transfer mediums. The hydrogenated base stock is well suited to
combat the problems of carbon formation on heated surfaces and
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCT 46P
January 27, 2011
Operating
Temperature Range 20 to 600°F
Viscosity
@ 40°C, cSt 42.7
@ 100°C, cSt 6.5
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
THERMOYLE HT SERIES
Physical Properties
PRODUCTS 50HT 100HT 200HT
Operating Temp Range -50 to 500°F -20 to 600°F 0 to 575°F
Viscosity
@ 0 ºF, cSt 49.80 326.00 812.00
@100 ºF, cSt 5.30 18.20 31.85
@200 ºF, cSt 1.70 4.38 5.67
December 2, 2010
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
TM SERIES
Product Data Sheet The Summit TM Series is formulated from highly refined hydro-
cracked base stocks and the unique additive SYNTHOLATE. The
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
addition of SYNTHOLATE inhibits the formation of varnish and
carbon and provides superior thermal and oxidative stability.
Utilizing the superior petroleum base stocks fortified with
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • 800.749.5823 • Fax 903.581.4376
Physical Properties
PRODUCTS TM-10 TM-15 TM-20 TM-30 TM-40
Viscosity
@ 40°C, cSt 31.2 46.0 66.3 99.2 146.6
@ 100°C, cSt 5.27 6.72 8.48 11.24 14.59
@ 100°F, SUS 163 237 346 524 769
@ 210°F, SUS 43.9 48.7 54.8 64.7 77.9
Viscosity Index 99 98 97 99 98
Pour Point, °F (°C) -44 (-42) -25 (-32) -38 (-38) -33 (-36) -27 (-33)
Flash Point,°F (°C) 440 (227) 470 (243) 470 (243) 520 (271) 495 (257)
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
SUMMIT ULTIMA® SERIES
Product Data Sheet Summit Ultima® is a high performance lubricant formulat-
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current .
ed specifically to outperform other synthetic rotary compressor
lubricants on the market. Ultima employs a unique base
stock that allows improvements in oxidation resistance and
sludge and deposit formation over conventional synthetic
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS Ultima-32 Ultima-46 Ultima-68
June 15, 2010
ISO Grade 32 46 68
Viscosity
@ 40°C, cSt 32.2 50 63.2
@ 100°C, cSt 5.61 7.35 9.28
@ 100°F, SUS 166 257 325
@ 210°F, SUS 45.1 50.9 57.5
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
UNIPAR FG SERIES
Product Data Sheet UniPar FG Series gear oils are specially formulated for gear
systems operating in the food service and packaging industries.
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
UniPar FG Series lubricants are NSF Registered and meet USDA 1998
(H-1) guidelines (lubricants with incidental food contact). In addition,
these gear oils are Kosher/Halal approved and CFIA accepted. Summit
is an ISO 21469 certified facility. UniPar FG lubricants are fortified
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
UniPar FG Series gear oils are ideal for the lubrication of production
equipment in beverage canning, bottling operations, meat and poultry
processing, dairy operations, fruit and vegetable processing, bakeries,
and pharmaceutical plants.
Physical Properties
March 9, 2012
Viscosity
@ 40°C, cSt 146 226 341 483 700
@ 100°C, cSt 14.5 19.3 31.0 40.2 54.3
Pour Point, °F 0 -6 5 0 -6
(°C) (-18) (-21) (-15) (-18) (-21)
NSF Registered H1 H1 H1 H1 H1
ISO 21469 Yes Yes Yes Yes Yes
Kosher Approved Yes Yes Yes Yes Yes
Halal Certified Yes Yes Yes Yes Yes
CFIA Accepted Yes Yes Yes Yes Yes
Shelf Life: Product shelf life is 3 years from the date of manufacture, after
which the product should be recertified prior to use.
LUBRICANT ADDITIVE
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
VARNASOLV
Equipment Varnish Cleaner
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current.
The use of petroleum lubricants, mainly automatic transmission
fluid (ATF), in rotary screw compressors, rotary vane compressors
and other high temperature equipment, results in varnish and
carbon formation. The varnish and carbon deposited throughout
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely
Product Data Sheet
Wind Turbine Cleaner
varying conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of January 25, 2011.
Varnish and Sludge Cleaner
Wind turbine gearbox lubricants perform in difficult
environments. Shock loading, extended oil drain serv-
ice intervals, temperature and humidity extremes can
rapidly break down the best formulated lubricants, pro-
ducing varnish and sludge as natural decomposition by-
products. Summit’s Wind Turbine Cleaner is the
P.O. Box 131359 • Tyler, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Clean-Out Procedure:
Simply replace 10% of the existing oil charge with an equal
amount of Summit Wind Turbine Cleaner, and then
January 25, 2011
PHYSICAL PROPERTIES
Viscosity, 40ºC, cSt 78
Specific Gravity, 60ºF 0.985
Density, 60ºF 8.20 lbs/gal
Flash Point 193ºC / 380ºF
NSF Registered HX-2
SUPER INDUSTRIAL DEGREASER & CLEANER
NOTE: The information in this publication is the result of careful testing in our laboratories, complemented by selected literature. It does not in any way constitute a guarantee, nor does it serve as a license to operate any patent. Due to widely varying
Xtra-Clean
Product Data Sheet
conditions of product use, which are beyond our control, it is strongly recommended that the product be tested for suitability. Product typical properties in this publication are current as of November 9, 2010.
Summit Xtra-Clean is a water-based, environmentally safe,
industrial-strength degreaser and cleaner which will quickly lift
and suspend oil and dirt. It is specially developed to clean oily
and greasy surfaces such as oil rigs, engines and cleaning vats with
a synthetic detergent that provides a noncaustic cleaner. Xtra-Clean
P.O. Box 131359 • Tyler, CR 2120, Texas 75713, Phone 903.534.8021 • Fax 903.581.4376
Physical Properties
PRODUCTS Xtra-Clean
pH: 13.0
Color: Clear
Odor: Fresh
Density: 8.34 lbs/gal
Flash Point: None
Rinse Ability: Completely
Type Cleaner Water Soluble
Degreaser
Active Ingredients: Detergents, Builders
Soluble Solvents
Degreasing Efficiency Excellent
Specific Gravity 1.045
Stability (Hot or Cold): Excellent
Ferrous Metals None
Non-Ferrous Metals None
NSF Registered A8 and C1
Caution: Contains alkaline silicates. May be harmful if swallowed.
Can cause eye and skin irriation