Beruflich Dokumente
Kultur Dokumente
SyncMaster 330TFT
SyncMaster 530TFT
SyncMaster 331TFT
SyncMaster 531TFT
SERVICE Manual
2. Reference Information
3. Product Specifications
4. Operating Instructions
6. Troubleshooting
8. Block Diagram
SAMSUNG
EXIT MENU
- +
1-1-1 Warnings
1. For continued safety, do not attempt to modify the (READING SHOULD
circuit board. NOT BE ABOVE 0.5mA)
1. Immediately before handling any semiconductor 6. Do not remove a replacement ESD from its
components or assemblies, drain the electrostatic protective package until you are ready to install it.
charge from your body by touching a known earth Most replacement ESDs are packaged with leads
ground. Alternatively, wear a discharging wrist- that are electrically shorted together by conductive
strap device. To avoid a shock hazard, be sure to foam, aluminum foil or other conductive materials.
remove the wrist strap before applying power to 7. Immediately before removing the protective
the monitor. material from the leads of a replacement ESD,
2. After removing an ESD-equipped assembly, place it touch the protective material to the chassis or
on a conductive surface such as aluminum foil to circuit assembly into which the device will be
prevent accumulation of an electrostatic charge. installed.
3. Do not use freon-propelled chemicals. These can Caution: Be sure no power is applied to the
generate electrical charges sufficient to damage chassis or circuit and observe all
ESDs. other safety precautions.
4. Use only a grounded-tip soldering iron to solder or
8. Minimize body motions when handling
desolder ESDs.
unpackaged replacement ESDs. Motions such as
5. Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from
solder removal devices not classified as Òanti-staticÓ a carpeted floor can generate enough static
can generate electrical charges sufficient to damage electricity to damage an ESD.
ESDs.
2-1-2 Symbols
Hot Ground
Cold Ground
! Provides special safety considerations
2-1-2 Acronyms
LCD Panel TFT-LCD panel, RGB vertical stripe, normaly white, 15-Inch viewable,
0.297 (H) x 0.297 (V) pixel pitch, 13.3-Inch viewable, 0.264 (H) x 0.264 (V) pixel pitch
Input Sync Signal Type: Seperate H/V sync, Composite H/V, Sync-on-Green, automatic synchronization
without external switch of sync type
Level: TTL level
• SyncMaster 33*TFT/53*TFT complies with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
Separate Sync
Horizontal Vertical
Video
Video Video
Video
CC DD E E Q Q RR S S
Sync
Sync Sync
Sync
BB PP
AA O O
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
Separate Sync
Horizontal Vertical
Video
Video Video
Video
CC DD E E Q Q RR S S
Sync
Sync Sync
Sync
BB PP
AA O O
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
SAMSUNG
EXIT MENU
- +
Power Port
1 DC 12V
- +
2
Signal Cable
G
EXIT MENU
1 Power Button
3 4 5
2 Power Indicator
Figure 4-1. Front View and Control
EXIT
3 EXIT Button
4 - + Up / Down / + / – Buttons
MENU
5 MENU Button
SAMSUNG
EXIT
- +
MENU
2
Audio in port
1 MIC AUDIO
OUT IN
Headphone jack
External microphone jack
Microphone out port
Power port
SAMSUNG
EXIT MENU
BASS
7 Bass Button
MIN MAX
TREBLE
8 Treble Button
MIN MAX
MIC
10 Microphone
Your LCD monitor includes an internal microphone which you can turn On or Off using the rightmost
control of the Audio controls.
This system operates with a VESA DPMS Note 2: This monitor is EPA ENERGY STAR¨
compliant video card installed in your computer. compliant and NUTEK compliant when
You use a software utility installed on your used with a computer equipped with
computer to set up this feature. See the table VESA DPMS functionality. If your
below for details. computer system cannot support a display
power management function, you can
Table 4-4. Display Power Management Signaling (DPMS); 13.3” purchase an optional DPMS software
Power saving function EPA/NUTEK program to enable the power saving
State Normal function. Please contact Samsung or your
Operation Stand-By Suspend Mode Power Off Mode
Items Mode Position A Position B dealer for more information.
Horizontal Sync Active Inactive Active Inactive Note 3: For energy conservation, turn your
Vertical Sync Active Active Inactive Inactive
monitor OFF when it is not needed, or
when leaving it unattended for long
Video Active Blanked Blanked Blanked periods.
Amber Amber
Power
Green Amber Blinking Blinking Note 4: Audio Part is operated separately by
Indicator
(0.5 sec) (1 sec) control button.
Power 40 W (max.)
Less than Less than Less than
Consumption/hr 30 W
5W 5W 5W
(13.3”) (nominal)
Power 45 W (max.)
Less than Less than Less than
Consumption/hr 35 W
5W 5W 5W
(15”) (nominal)
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
5-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.
5-1-1 Removing the Stand 5. Disconnect Power Cord and Signal Cable.
Figure 5-3
Figure 5-4
Figure 5-6
10. Remove 4 screws on the Shield of Panel.
11. Remove the Shield. Figure 5-8
12. Disconnect the jack between Panel and
Inverter PCB.
13. Remove Rear Bracket.
2. Make a little gap between stand assembly and 5. Remove the screw and washer on the base of
Rear Cover with a ÔÐÕ screw driver. And pry the stand.
Rear Cover off stand assembly with the finger.
Figure 5-11
Figure 5-9
6. Remove the Stand Base and Stand Top.
3. Remove the 10 screws from the stand
assembly.
Figure 5-10
5-4 Reassembly
6-1 No Power
Yes
Yes
6-2 No Video
Yes
Yes
Replace IC106.
Yes
Replace IC101. Replace IC105 (seperate sync)
or IC104 (SOG).
18 19 20 1
No No
Does the sync pulses appear at Does the sync pulses appear at Check IC401 and IC101.
Pins 13 and 14 of IC110? Pins 2 and 3 of IC110?
Yes
Yes Replace IC110 or check its
related circuit.
2 3 4 5 10 11 12 13 14
No No Replace IC301 or check its
Do the sync pulses appear at Do the sync pulses appear at Pins
Pins 22, 23, 25 and 26 of IC310? 2, 3, 54, 55 and 56 of IC301? related circuit.
Yes
Yes Replace IC305 or check its
related circuit.
6
No Replace IC310 and IC311 or
Do the waveforms appear at
Pins 5 and 20 of CN301? check its related circuits.
Yes
WAVEFORMS
CH1 RMS = 3.6 V CH1 RMS = 3.1 V CH1 RMS = 2.3 V CH1 RMS = 2.8 V
CH1 RMS = 2.12 V CH1 RMS = 1.18 V CH1 RMS = 3.5 V CH1 RMS = 3.1 V
CH1 RMS = 4.56 V CH1 RMS = 2.3 V CH1 RMS = 3.25 V CH1 RMS = 2.35 V
CH1 RMS = 200 mV CH1 RMS = 50 mV CH1 RMS = 1.24 V CH1 RMS = 400 mV
20 IC110 #2
Yes
6-4 No OSD
WAVEFORMS
There is video but no OSD. 15 IC307 #12
17 IC307 #10
Yes
Yes
Does the sound input signal No Check Pins 1 and 2 of CN806 and
appear at Pins 6 and 11 of IC803? related circuits.
Yes
Yes
Does the DC 2.5 V bias appear at No Check CN813, ZD803, R821, R822,
Pin 16 of IC503? C815 on the Audio PCB.
Yes
Yes
Yes
Yes
Yes
Yes
OK
Yes
Yes
OK
Others
Loc. No. Code No. Description Specification Remarks
SyncMaster 33*TFT/53*TFT
8 Block Diagram
H DOT_CLK H V
R 8 R 8 R 6
R TDA8752 GMFC1 GMZ1 LVDS TFT
G 8 G 8 G 6 x2 LCD
G B 8 B 8 B 6 PANEL
B
DOT_CLK H/V/DOT_CLK H/V/EN/
DOT_CLK
FRAME
MEMORY
+5 V_S LM4863
+3.3 V_S VOLUME (Audio
12V VCC TONE CTRL. Amp)
+5 V_PLL
Speaker
+5 V_ADL
(SyncMaster 330TFT/530TFT)
8-1
8 Block Diagrams
Memo
PARTS TYPE NO. REF. NO. PARTS TYPE NO. REF. NO.
431 D115
BZX84C5V1 ZD101, ZD102, ZD103,
ZD104, ZD105, ZD401
C
KSC1623 Q301, Q302, Q401 MMBD4148 D101, D102, D103, D104,
D105, D106, D109, D110,
D401, D402, D403, D404
B
E
8 24LC211 IC403
1
8
C S19933ADY-T1 IC309
KSR2101 Q101
LM1881M IC104
1
B
E
LM2596 IC107, IC108
LM4863 IC803
16
MC34067P IC110
MC141544- IC307-
LM2576 IC805
1 DWR2
20
74FCT244 IC306
1 74FCT573M IC308
7045 IC402
PARTS TYPE NO. REF. NO. PARTS TYPE NO. REF. NO.
80
48 50
DS90CF561 IC310, IC311 TDA8752 IC101
100
1 1 30
150
100
50 GMFC1 IC301
416S1020B IC302, IC303, IC304
GMZ1 IC305
1
200
1 50
LEFT_AMP 1 8 LEFT_AMP
1 RIGHT – CN806 CN841
CN814 RIGHT_AMP 2 7 RIGHT_AMP
2 RIGHT + GND GND
3 6
MIC_EN 4 5 MIC_EN
1 LEFT – 5 4
CN815 5V 5V
2 LEFT +
5V 6 3 5V
LEFT_IN 7 2 LEFT_IN
RIGHT_IN 8 1 RIGHT_IN
NEUTRAL
AUDIO FUNC PCB
GND
LIVE
CN801
1
2
3
MIC_GND 1
CN805 MIC_SIG 2
1
2
3
4
5
C-MIC
LIVE
NC
GND
NC
NEUTRAL
GND
12 V
CN808 CN809 CN812 CN813
CN816 CN804
1
2
MIC_OUT PC_AUDIO EXT_MIC HEADPHONE
SMPS
1
2
3
PC_R_IN 1 1 PC_R_IN
12 V
12 V
GND CN101 PC_G_IN 2 2 PC_G_IN CN101
1 NC CN102 PC_B_IN 3 3 PC_B_IN
2 BRIGHT CN103 GND 4~9 4~9 GND
3 NC S_RASTER 10 10 S_RASTER
4 BL_EN GND 11 11 GND
SDA 12 12 SDA
POWER PCB
5 NC
LCD PANEL H_SYNC 13 13 H_SYNC
6 GND
7 5V V_SYNC 14 14 V_SYNC
MAIN PCB CN881
4 PWR
3 GND
2 VCC
SCL 15 15 SCL
1 LED
8 GND
9 GND GND 16
10 12V
11 12V
12 NS
1
2
3
4
CN301
KEY 1 1 KEY
LED
VCC
GND
PWR
CN401 VCC 2 2 VCC CN861 CN862
LED 3 3 LED
5V (15":12V)
5V (15":12V)
LVDS_DATA
KEY2 4 4 KEY2
GND 5 5 GND
GND
GND
20
19
1 18
Power Line
Signal Line
pin #
pin #
1024 x 768 / 85 Hz 1024 x 768 / 85 Hz 1024 x 768 / 85 Hz
1 12 1 12 1 12
2 GND 2 GND 2 5
3 5 3 5 3 GND
4 5
Unit: Vrms Unit: Vrms 5 GND
Unit: Vrms
MODES MODES
pin #
pin #
1 12 1 12
2 3.3 2 GND
3 GND 3 5
CH1 RMS = 3.6 V
4 3.3
5 GND Unit: Vrms
Unit: Vrms
2 5
3
4
16
6
15
17
12 13 14
10
11
Power Line
Signal Line
pin # MODES
1024 x 768 / 85 Hz
1 11.96
2 5.90
3 4.99
CH1 RMS = 3.1 V CH1 RMS = 2.3 V
4 5.8 mV
5 4.99
6 4.99
7 11.95
8 11.95
Unit: Vrms
pin #
pin #
1024 x 768 / 85 Hz 1024 x 768 / 85 Hz
1 59.8 mV 22 3.44
2 5 23 GND
3 5 24 4.16
4 5 25 5.01
5 4.62 26 4.97
6 0.457 27 4.46
7 4.91 28 4.43
8 5 29 4.78
9 GND 30 4.77
10 5.03 31 14.07
11 5.02 32 2.226
12 5.02 33 2.238
13 NC 34 5.03
14 NC 35 5.03
15 4.94 36 4.96
16 93.7 mV 37 4.96
17 3.217 38 52.7 mV
18 4.97 39 4.96
19 5.01 40 4.87
20 63.0 mV 41 GND
21 0.476 42 9.7 mV
Unit: Vrms
pin #
1024 x 768 / 85 Hz
1 NC
2 NC
3 NC
4 GND
5 4.43
6 4.46
7 4.87
8 5.03
Unit: Vrms
pin #
1024 x 768 / 85 Hz
1 GND
2 GND
3 GND
4 GND
5 5.03
6 5.03
7 GND
8 5.03
Unit: Vrms
Power Line
pin #
1024 x 768 / 85 Hz
1 GND
2 GND
3 Signal (+2.5 V Bias)
4 5
5 Signal (+2.5 V Bias)
6 Input Signal (+2.5 V Bias)
7 GND
8 2.5
9 2.5
10 2.5
11 Input Signal (+2.5 V Bias)
12 Signal (+2.5 V Bias)
13 5
14 Signal (+2.5 V Bias)
15 GND
16 2.5 V (Headphone : 5 V)
Unit: Vrms
Memo