Beruflich Dokumente
Kultur Dokumente
CAUTION
Make sure to turn the power off before you start
Optional Accessory
Use the tado° Trim Plate behind the Smart Thermostat or Extension
Kit if needed. This can be obtained separately at tado.com/installers
1. Wiring: OpenTherm
Wired Setup:
Smart Thermostat is wired directly to the boiler
Smart Thermostat
Wireless Setup:
Smart Thermostat installed wirelessly with receiver
4
OpenTherm
OT
MAX 36V DC
OT
5
2. Connect Internet Bridge to Router
OpenTherm
6
3. Pair Extension Kit with Internet Bridge
OpenTherm
Wireless Setup: Smart Thermostat installed wirelessly with receiver
3 SEC
Blinking
4x short - pause - ...
2 MIN
Fast
Blinking
Blinking If failed:
2x short - pause - ... Restart pairing and make sure that the distance
between the devices is at least 3 m while pairing
7
4. Pair Smart Thermostat with Internet Bridge
OpenTherm
2 MIN
3 SEC
If failed:
• Press the button to clear the error
• Restart pairing and make sure that the distance
between the devices is at least 3 m while pairing
8
Open Installer Menu
OpenTherm
2 MIN
3 SEC 3 SEC
If failed:
• Repeat entering the Installer Menu
• Make sure that the distance between the devices is
at least 3 m while loading the menu
9
%QPƂIWTCVKQPOpenTherm
OpenTherm
Wired Setup:
Smart Thermostat is wired
directly to the boiler
Wireless Setup:
Smart Thermostat installed
wirelessly with receiver
1
OpenTherm
2 MIN
No
Extension Kit
OpenTherm
installation complete
2 MIN
11
1. Wiring: Viessmann KM Bus
Wireless Setup:
Smart Thermostat installed wirelessly with receiver
2
The Smart Thermostat cannot be connected directly to
Viessmann KM Bus systems, an Extension Kit is required.
MAX 36V DC
Viessmann
KM Bus
1 2
21
2. Connect Internet Bridge to Router
22
3. Pair Extension Kit with Internet Bridge
3 SEC
Blinking
4x short - pause - ...
2 MIN
Fast
Viessmann
Blinking
Blinking If failed:
2x short - pause - ... Restart pairing and make sure that the distance
between the devices is at least 3 m while pairing
2
4. Pair Smart Thermostat with Internet Bridge
2 MIN
3 SEC
Viessmann
If failed:
• Press the button to clear the error
• Restart pairing and make sure that the distance
between the devices is at least 3 m while pairing
24
Open Installer Menu
2 MIN
3 SEC 3 SEC
Viessmann
Press button Press button Installer Menu is Ready for
for 3 sec - for 3 sec - loading KWVՏO]ZI\QWV
release release
If failed:
• Repeat entering the Installer Menu
• Make sure that the distance between the devices is
at least 3 m while loading the menu
25
%QPƂIWTCVKQP8KGUUOCPPKM Bus
Wireless Setup:
Smart Thermostat installed
wirelessly with receiver
Select Select No
Temperature Heating Hot Water
Sensor Circuit Control
Viessmann
26
2 MIN
Viessmann
D37
+WVՏO]ZI\QWVLW_VTWILIK\Q^M
after saving installer menu
(up to 2 min)
27
82
Viessmann
6. Heating System Settings
For the heating circuit controlled by tado°, set the same settings as for a
Viessmann Vitotrol 200 remote control.
Viessmann
b5: Heating Circuit 5
(If 5 can not be
Pump Logic selected, use 1)
29
Get expert advice on the
tado° installer hotline:
101961_C