Beruflich Dokumente
Kultur Dokumente
Resumen—La masa unitaria se usa para determinar los valores de la misma necesarios para la sección de las
proporciones de los agregados en las mezclas de concreto, la masa unitaria puede ser usada también para la
determinación de la relaciones masa/volumen para los acuerdos de compra. Sin embargo, se desconoce la
relación entre el grado de compactación de los agregados en una unidad de acarreo o en una pila de almacenaje
y el determinado por este método. Así mismo, los agregados en las unidades de acarreo o en las pilas de
almacenaje usualmente contienen humedad absorbida y superficial (esta última afecta al análisis volumétrico),
mientras que la norma determina la masa unitaria con base en los agregados secos. Se incluye un procedimiento
para el cálculo del porcentaje de vacíos entre las partículas de agregado, basado en la masa unitaria determinada.
Abstract— The unit mass is used to determine the values required for the same section of the proportions of
aggregates in concrete mixtures, the unit weight may also be used to determine the mass / volume relationships
for purchase agreements. However, the relationship between the degree of compaction of the aggregates on a
carrying unit or a stack of storage and thus determined is unknown. Likewise, aggregates hauling units or
storage batteries usually contain absorbed and surface moisture (the latter affects the volumetric analysis),
whereas the norm determines the unit weight based on the dry aggregates. A procedure for calculating the
percentage of voids between the aggregate particles, based on the determined unit mass is included.
% Vacíos = 99,99 S *F
donde:
Masa unitaria Compacta
3
M = masa unitaria del agregado (kg/𝑚 )
molde A
G = masa del agregado más el molde (kg)
𝑀 = (𝐺 − 𝑇 ) ∗ 𝐹
T = masa del molde (kg)
𝑀 = (11,0232 − 3,075 ) ∗ 𝐹
V = volumen del molde (𝑚3 )
M = 1,9482 kg F
F = factor para el molde (1/𝑚3 )
100[(𝑆 ∗ 𝑊) − 𝑀]
% 𝑉𝑎𝑐í𝑜𝑠 =
Masa unitaria Suelta (𝑆 ∗ 𝑊)
M = 7,2414 kg F
molde B
100[(𝑆 ∗ 𝑊) − 𝑀]
% 𝑉𝑎𝑐í𝑜𝑠 = M= (𝐺 − 𝑇 ) ∗ 𝐹
(𝑆 ∗ 𝑊)
𝑀 = (6,5312 − 1,731 ) ∗ 𝐹
donde
molde B
M= (𝐺 − 𝑇 ) ∗ 𝐹 Agregado Grueso
𝑀 = (𝐺 − 𝑇 ) ∗ 𝐹
Promedio = 7,148 kg
𝑀 = (7,611 − 3,074 ) ∗ 𝐹
Tabla 4. Datos masa unitaria Compacta.
M = 4,537 kg F
Recipiente + arena,
Prueba
molde (kg) 100[(𝑆 ∗ 𝑊) − 𝑀]
1 7,637 % 𝑉𝑎𝑐í𝑜𝑠 =
(𝑆 ∗ 𝑊)
2 7,595
3 7,768 100[(𝑆 ∗ 998) − 4,537]
4 7,560 % 𝑉𝑎𝑐í𝑜𝑠 =
(𝑆 ∗ 998)
5 7,495
% Vacíos = 99,99 S*F
Promedio = 7,611 kg
100[(𝑆 ∗ 𝑊) − 𝑀]
% 𝑉𝑎𝑐í𝑜𝑠 =
(𝑆 ∗ 𝑊)