Beruflich Dokumente
Kultur Dokumente
- This is the menu to select the unit using for the project
- This is fixed in this project.
<Client Data>
1. Project Data
: This is the menu to input the title, designer, date and comment of the project.
2. Client Data
: This is the menu to input the information of the client.
If you input the new city date to DB, you click the button, “Add City”
3. Climatic Design Data
: This is the menu to input the indoor/outdoor design conditions
These values are filled automatically from DB by selecting the city which is at
“Client Data”
<Master Data>
1
11 9 12 13
2
3 4
5
6
7
8 9 10 9 14
15 16 17 18 19 20 21
2. Ground Reflectance
3. Ceiling Height
4. Wall Height
5. Operation Time
: This is the menu to input the building opening and closing hour
If you enter the actual U-factor of your roof, wall or partition, click the button.
10. Wall Data Color
If you input typical value for glass U-factor, select the item in the table
If you input typical value for glass U-factor, select the item in the table
17. Glass Shading Coefficient
If you input typical value for glass shading coefficient, select the item in the table
15
2
16
3 4
17
5 6 7
18
8 9 10 11
19
12
20
13
14 21
1. Zone Control
- Add Zone : add new zone
- Zone No. : select a zone made already
- Zone Name : display the current zone name
2. External Load
- Dimension
: This is the menu to enter the dimension of the zone.
3. Select Roof Type
- This is the menu to select the roof among the roof input at Master Data
- This is menu to enter the direction of the wall faces or “P” for a partitions.
- This is the menu to select the glass type among the entry.
9. Glass Shading Device
- You can use these values or input a value you want directly.
- This menu is needed to determine the actual size of glass using for calculation.
11. Glass Reference
1. Zone Grouping
- At “Select a group”, select a air conditioner
- Select a zone name at the left box, and click the button “>” to move into the
right box which will be used to determine the “Aircon-1”. Or to use all zone,
click the button, “>>”
- To remove a zone from right box, click the button, “<”. Or to remove all zone
in the right box, click the button “<<”
- For model selection, click “Determine” or to resume click “Cancel”
2. Determined Specification
- To select model, select electric range, type and grade and model name.
- Table below will be show the model specification.
- If you want to select model again, click “Resume”
- If you detailed model information for PDF file, click “Detail Information”
3. Simulation
- This is the menu to calculate the capacity for a given design condition.
<NOISE>
1. Path Input
: This is to enter the sound path and is composed of add, edit, delete button
If there is the octave band data in the model database, manufacturer’s data is
entered automatically
1.1 Add
If you press the add button the following window will be opened. You can enter the
manufacturer’s data for each path.
When the input is finished it will be added to the path window as follows.
1.2 Edit
After selecting the path you want to edit form the path list window, press the edit
button. The sane window as when add is executed will be opened so that the
manufacturer’s data of the path can be edited. The data of the selected path are
shown for each band.
1.3 Delete
This is the button to delete the selected path. Press the delete button after
selecting the path you want to delete and it will b deleted.
2. Attenuation Input
This is to enter the attenuation composing the selected path. It is composed of add,
edit, and delete button.
2.1 Add
If you select the path you want to enter and press the add button, the following
window will be opened. Select the attenuation of the 7 attenuations and then press
the OK button. A window applicable to the selected attenuation will be opened.
If you select the applicable attenuation symbol, the applicable input window will
be opened for each attenuation type.
2.2 Edit
If you select the path you want to edit and press the edit button, the input window
will be opened for each attenuation type. When selecting the attenuation the
applicable path must be selected.
2.3 Delete
Select the attenuation type you want to delete and press the delete button. This
will delete the applicable attenuation.
3. Calculate Noise
If you press the calculate noise button after selecting the NC value, the noise and
audio value for the calculated space will be displayed in a window. Here press the OK
button when it satisfies the NC value and press the not satisfied button when it doesn’t.
This is the menu to calculate the pressure loss of the free discharge
This is the menu to calculate the pressure loss of the transitions for changing pipe size.
This is the menu to calculate the pressure loss of the damper
This is the menu to calculate the pressure loss of the other devices.