Beruflich Dokumente
Kultur Dokumente
______________
Questions 1-10 carry 1 mark each, place X in the box alongside the answer of your choice.
The marks for all other questions are shown in the box at the end of each question. Answer in
the space provided. Keep your answers brief. The space allocated should be sufficient.
3. Regulation 6 of Lifting Operations and Lifting Equipment Regulations (LOLER ’98) refers
to:
Lifting persons
Keeping records
Reporting defects
Positioning & installation
5. What is the meaning of the IMDG document issued by the International Maritime
Organisation?
International Maritime Dangerous Goods code
International Maritime Dangerous Goods and Cargo regulations
International Marine and Docks guidance code
International Marine Dangerous Goods code
1
Examination Paper – OCS – v1.0 14th November 2012
7. To what vertical angle of tilt must an offshore container be able to sustain without turning
over (in accordance with DNV 2.7.1 and EN 12079?
35°
20°
30°
25°
8. What is the maximum distance allowable between forklift pockets (centre to centre) that
are built into an offshore container?
2000mm
2050mm
2150mm
2250mm
9. For lifting sets, what is the correct method of rating a 4-leg wire rope sling that is to be
attached to an offshore container
2.1 x WLL for a single leg x cos ß – 1 x WLL
2.1 x WLL for a single leg x cos ß
3 x WLL for a single leg x cos ß – 1 x WLL
3 x WLL for a single leg x cos ß
10. What is the recommended minimum size of a sling set master link that shall be attached to
a crane hook?
270mm x 140mm
280mm x 140mm
300mm x 160mm
310mm x 160mm
11. The following abbreviation, TEU, is commonly associated with offshore containers. What
does this abbreviation represent?
12. Conventional ISO containers with ISO corners cannot be used offshore. One reason is
they do not have pad eyes, what is the other reason?
2
Examination Paper – OCS – v1.0 14th November 2012
13. Referring to the illustration below of a typical offshore container, secondary structure
components, name the following parts:
Part A
Part B
Part C
Part D
Part E
D
C
3
Examination Paper – OCS – v1.0 14th November 2012
14. Referring to the illustration below of a typical offshore container, primary structure
components, name the following parts:
Part A
Part B
Part C
Part D
Part E
Part F
Part G
Part H
Part I
Part J
B
A
C
J
D
H
I
4
Examination Paper – OCS – v1.0 14th November 2012
15. In order to prevent lateral bending moments on pad eyes, they shall be aligned with the
sling to the centre of lift, with a maximum manufacturing tolerance of <________>
degrees?
16. Referring to pad eyes, what is the maximum tolerance between the diameter of the
shackle pin and the diameter of the pad eye hole?
_____________________________________________________________________________
17. When designing pad eyes, what other three dimensional factors must be taken into
account?
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
5
Examination Paper – OCS – v1.0 14th November 2012
18. The tolerances between pad eye thickness and the inside width of the shackle is clearly
stated in both EN12079-1 and DNV 2.7.1. State these tolerances in the space provided
below against the appropriate standard:
(i) EN12079-1
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
(iv)__________________________________________________________________________
(v)___________________________________________________________________________
(vi)__________________________________________________________________________
(vii)__________________________________________________________________________
(viii)__________________________________________________________________________
6
Examination Paper – OCS – v1.0 14th November 2012
20. What information is required to be marked on an offshore container lifting set?
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
(iv)__________________________________________________________________________
(v)___________________________________________________________________________
(vi)__________________________________________________________________________
(vii)__________________________________________________________________________
21. Container lifting sets must be certified. List the 6 minimum items that must be present on
the certificate:
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
(iv)__________________________________________________________________________
(v)___________________________________________________________________________
(vi)__________________________________________________________________________
22. Following a container load test, name two further verification procedures that must be
carried out before the container can be passed as fit for a further period of service:
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
7
Examination Paper – OCS – v1.0 14th November 2012
23. When carrying out the proof load testing of an offshore container, what are the four most
important considerations that the competent person should take into account regarding
the distribution of the test load?
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
(iv)__________________________________________________________________________
24. (a) How long would you suspend an offshore container with the full test load when
applying a proof load test?
(b) At what height from the ground must the container be held at?
(a)
(b)
25. Detail the acceptance/rejection criteria that you would apply to a wire rope sling fitted to
an offshore container to EN 12079 when carrying out a thorough examination. All
acceptance and rejection criteria must be stated.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
8
Examination Paper – OCS – v1.0 14th November 2012
26. List 10 items that should be included in an offshore container inspection report:
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(iii)__________________________________________________________________________
(iv)__________________________________________________________________________
(v)___________________________________________________________________________
(vi)__________________________________________________________________________
(vii)__________________________________________________________________________
(viii)__________________________________________________________________________
(ix)__________________________________________________________________________
(x)___________________________________________________________________________
27. Detail the acceptance/rejection criteria that you would apply to an EN13889 alloy steel
shackle fitted to an offshore container lifting set to EN 12079 when carrying out a
thorough examination. All acceptance and rejection criteria must be stated.
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
9
Examination Paper – OCS – v1.0 14th November 2012
28. The IMDG states that offshore tank containers that are certified for dangerous good are to
be subjected to what two types of verification?
(i)___________________________________________________________________________
(ii)___________________________________________________________________________
(a)
(b)
(c)
30. Offshore container roof markings are required by both DNV and EN standards.
_______________________________________________________
_______________________________________________________
10
Examination Paper – OCS – v1.0 14th November 2012
31. If an offshore container has a tare weight of 1850Kg and the maximum gross weight of
the container is 9500Kg, what is the maximum payload?
_____________________________________________________________________________
32. If an offshore container is rated at maximum gross weight of 12000Kg and the payload
required is 11100Kg, what is the maximum design tare weight allowable for the
container?
_____________________________________________________________________________
33. With regard to offshore containers, what is the definition of the term CSC?
_____________________________________________________________________________
11
Examination Paper – OCS – v1.0 14th November 2012