Beruflich Dokumente
Kultur Dokumente
MANUAL DE INSTALACIÓN/USUARIO
AIRE
ACONDICIONADO
AC Smart BACnet
PBACNA000
www.lg.com
P/NO : MFL69023103
NOTAS EXPLICATIVAS i
NOTAS EXPLICATIVAS
ESPAÑOL
Copyrights
El contenido del Manual de usuario del modelo AC Smart BACnet está protegido por leyes de
copyright internacionales y la Ley de Protección de Programas Informáticos. El contenido de este
Manual de usuario y de los programas mencionados en el mismo solo podrán utilizarse bajo licencia
de LG Electronics, respetando estrictamente las estipulaciones del contrato de usuario.
Queda prohibida la reproducción y distribución, por cualquier medio, de copias de este Manual de
usuario o parte del mismo, sin la aprobación previa de LG Electronics.
Interfaz de AC Manager IV
Puede conectar AC Smart BACnet con un AC Manager IV basado en ordenador para utilizar las
diversas funciones de AC Manager IV. También puede utilizar la función de programación, incluso
mientras el ordenador con AC Manager IV está apagado.
NOTAS EXPLICATIVAS iii
ESPAÑOL
en un lugar de fácil acceso.
• Las pulsaciones de teclado que usa el sistema se indican con texto en negrita entre
paréntesis angulares (< >).
Ejemplo: <Esc>
MEMO
iv
ESPAÑOL
ÍNDICE v
ÍNDICE
ESPAÑOL
1 PRECAUCIONES DE 61 NOTES
SEGURIDAD 61 BIBBs
61 – Data Sharing BIBBS
7 PREPARACIÓN 63
64
– Alarm and Event Management BIBBS
– Scheduling BIBBS
7 Descripción general de AC Smart
BACnet 64 – Trending BIBBS
7 Componentes 65 – Device Management BIBBS
8 Especificaciones del producto 66 – Device Management BIBBS
9 Características y funciones 66 – Network Management BIBBS
11 Instalación y configuración 68 Multi - state Input Object Type
11 – Instalación 68 – Multi - state Output Object Type
21 – Cómo configurar una función de 70 AC Smart BACnet Error Response
parada de emergencia Table
22 Método de introducción de 70 – Error PDU
información 70 – Reject PDU
71 – Abort PDU
23 INICIO
23 Encendido/apagado de la pantalla 72 CONSEJO
23 – Encendido de la pantalla 72 Códigos de control
23 – Apagado de la pantalla 72 Códigos de error
24 Reinicio 72 – Error de dispositivo interior, ERV o
24 Inicio y cierre de sesión ERV DX, AWHP (Kit hidro), UTA
75 – Errores de unidad exterior
PRECAUCIONES DE SEGURIDAD
ESPAÑOL
• Este producto debe instalarlo un instalador profesional de un centro de servicio autorizado
por LG.
• Los problemas derivados de la instalación por parte de una persona no autorizada serán
responsabilidad del usuario, y no estarán cubiertos por la garantía.
• Las siguientes advertencias de seguridad tienen como finalidad evitar peligros o daños
imprevistos.
• Este producto se ha diseñado para uso profesional, o para zonas fuera de hogares, y ha
superado la Prueba de interferencias electromagnéticas.
ADVERTENCIA
Puede resultar en lesiones graves o la muerte cuando se tienen en cuenta las instrucciones
PRECAUCIÓN
Puede resultar en lesiones leves o daños en el producto cuando las instrucciones son
ignoradas
ADVERTENCIA
instalación
yy Si desea reinstalar el producto, póngase en contacto con el distribuidor en el que compró
el producto, o con un centro de servicio, para solicitar el servicio de reinstalación.
-- La instalación del producto por parte de una persona no autorizada podría provocar un incen-
dio, una descarga eléctrica, una explosión, lesiones o fallos de funcionamiento del producto.
yy No retuerza ni dañe el cable de alimentación.
-- Podría provocar un incendio o descargas eléctricas.
yy Para los trabajos eléctricos, póngase en contacto con el distribuidor en el que compró el
producto o con un centro de servicio.
-- Si una persona no autorizada realiza el desmontaje o la reparación podría producirse un incen-
dio o una descarga eléctrica.
yy Instale el producto en una zona protegida de la lluvia.
-- Si accede agua al producto podrían producirse fallos de funcionamiento.
yy No instale el producto en una zona húmeda.
-- Si el producto se humedece, podría presentar fallos de funcionamiento.
2 PRECAUCIONES DE SEGURIDAD
yy Para la instalación del producto, póngase en contacto con el distribuidor en el que compró
el producto o con un centro de servicio.
-- La instalación del producto por parte de una persona no autorizada podría provocar un incen-
ESPAÑOL
dio, una descarga eléctrica, una explosión, lesiones o fallos de funcionamiento del producto.
yy Para los trabajos eléctricos, encargue a un electricista el trabajo pidiéndole que se base
en el manual de instalación y en el diagrama eléctrico especificado.
-- El uso de un cable inadecuado o permitir que una persona no profesional realice los trabajos
eléctricos podrían provocar incendios o descargas eléctricas.
yy No coloque el producto cerca de fuentes de fuego.
-- Si lo hace, el producto podría incendiarse.
yy Si el producto se instala en un hospital o en una estación base de comunicaciones, instale
equipos de protección suficientes contra el ruido.
-- Si no lo hace, el producto podría funcionar incorrectamente o provocar que otros productos lo
hicieran.
yy Afiance la instalación del producto correctamente.
-- Si el producto no se instala con firmeza, podría caerse o presentar fallos de funcionamiento.
yy Lea el manual detenidamente para instalar el producto de forma correcta.
-- En caso contrario, una instalación incorrecta podría provocar un incendio o una descarga eléctrica.
yy A la hora de realizar el cableado del producto, no utilice un cable no convencional ni
extienda el cable hasta una longitud excesiva.
-- Podría provocar un incendio o descargas eléctricas.
yy Instale correctamente el cable de alimentación y el cable de comunicaciones.
-- Una instalación insegura podría provocar un incendio o una descarga eléctrica.
yy No conecte el cable de alimentación al terminal de comunicaciones.
-- Esto podría provocar un incendio, una descarga eléctrica o fallos de funcionamiento del producto.
Uso
yy No coloque objetos pesados sobre el cable de alimentación.
-- Podría provocar un incendio o descargas eléctricas.
yy No cambie ni realice extensiones arbitrarias del cable de alimentación.
-- Podría provocar un incendio o descargas eléctricas.
yy Utilice el cable específico del producto.
-- El uso de un cable no convencional no autorizado podría provocar un incendio o una descarga
eléctrica.
yy No utilice un dispositivo de calefacción cerca del cable de alimentación.
-- Podría provocar un incendio o descargas eléctricas.
yy Asegúrese de que nunca entra agua al producto.
-- Podrían producirse una descarga eléctrica o fallos de funcionamiento.
yy No coloque ningún recipiente con líquido sobre el producto.
PRECAUCIONES DE SEGURIDAD 3
ESPAÑOL
-- Podría provocar un incendio o descargas eléctricas.
yy Utilice componentes convencionales.
-- El uso de un producto no autorizado podría provocar un incendio, una descarga eléctrica, una
explosión, lesiones o fallos de funcionamiento del producto.
yy Si se sumerge el producto en agua deberá ponerse en contacto con un centro de servicio.
-- Podría provocar un incendio o descargas eléctricas.
yy No golpee el producto.
-- El producto podría presentar fallos de funcionamiento.
yy No guarde ni utilice gases combustibles ni sustancias inflamables cerca del producto.
-- Esto podría provocar un incendio o fallos de funcionamiento del producto.
yy No desmonte, repare ni modifique el producto de forma arbitraria.
-- Podría provocar un incendio o descargas eléctricas.
yy Los niños y las personas de edad avanzada deberán utilizar el producto bajo la
supervisión de un tutor.
-- Un uso descuidado del producto podría provocar un accidente o fallos de funcionamiento.
yy El tutor debe evitar que los niños accedan al producto.
-- El producto podría sufrir daños o caerse, provocando lesiones a los niños.
yy Respete el rango de temperatura operativa especificado en este manual.
Si en el manual no se indica rango de temperatura operativa alguno, utilice el producto
entre 0 y 40 ºC (32 y 104 °F).
-- Si se utiliza el producto fuera de este rango el producto podría sufrir daños importantes.
yy No pulse los interruptores ni los botones con objetos afilados.
-- Podrían producirse una descarga eléctrica o fallos de funcionamiento.
yy No cablee el producto mientras se encuentra encendido.
-- Podría provocar un incendio o descargas eléctricas.
yy Si el producto emite sonidos o genera olores diferentes, deje de utilizarlo.
-- Podría provocar un incendio o descargas eléctricas.
yy No coloque objetos pesados sobre el producto.
-- El producto podría presentar fallos de funcionamiento.
yy No rocíe agua sobre el producto ni lo utilice con un paño sumergido en agua.
-- Podría provocar un incendio o descargas eléctricas.
yy No utilice el producto para la conservación de animales y plantas, instrumentos de
precisión, obras de arte ni con fines especializados.
-- Podrían producirse daños materiales.
yy Deshágase del material de embalaje de forma segura.
-- El material de embalaje podría provocar lesiones personales.
4 PRECAUCIONES DE SEGURIDAD
PRECAUCIÓN
instalación
ESPAÑOL
Uso
yy Limpie el producto con un paño suave, pero no con un detergente con base disolvente.
ESPAÑOL
-- El uso de un detergente con base disolvente podría provocar un incendio o deformar el pro-
ducto.
yy No toque el panel utilizando un objeto puntiagudo o afilado.
-- Podrían producirse una descarga eléctrica o fallos de funcionamiento.
yy No deje que el producto entre en contacto con sustancias metálicas.
-- El producto podría presentar fallos de funcionamiento.
yy Durante los procesos de esterilización y desinfección deberá dejar de utilizar el producto.
-- El producto podría funcionar de una forma anómala.
yy No toque el interior del producto.
-- El producto podría presentar fallos de funcionamiento.
yy Compruebe el estado del producto después de no utilizarlo durante un periodo de tiempo
prolongado.
-- Si el producto va a utilizarse durante un periodo de tiempo prolongado, el producto podría
funcionar incorrectamente y provocar lesiones al usuario.
yy No deje el producto cerca de un florero, una botella de agua ni ningún otro líquido.
-- Podría provocar un incendio o descargas eléctricas.
yy Si el cristal líquido del producto se rompe, no permita que su piel, por ejemplo, la cara,
entre en contacto con el cristal.
-- Podría sufrir lesiones o causar daños materiales.
Dispositivo de Clase A
ESPAÑOL
NOTA
Este equipo ha sido probado y ha demostrado cumplir con los límites para un dispositivo digital
Clase A, conforme a la parte 15 de las normas FCC.
Estos límites están diseñados para proporcionar una protección razonable contra las
interferencias perjudiciales cuando el equipo se utiliza en un entorno comercial.
Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y
utiliza de acuerdo con el manual de instrucciones, puede causar interferencias perjudiciales
en las comunicaciones. El funcionamiento de este equipo en un área residencial puede
causar interferencias perjudiciales interferencias, en cuyo caso el usuario deberá corregir la
interferencia a su propio costo.
PRECAUCIÓN
PREPARACIÓN
ESPAÑOL
Este apartado contiene información sobre los componentes de AC Smart BACnet, cómo instalarlos
y configurarlos, y otra información necesaria para utilizar el producto.
Componentes
La caja del paquete incluye los siguientes componentes. Abra la caja y asegúrese de que incluye
todos los componentes.
AC Smart BACnet
ESPAÑOL
MANUAL DE INSTALACIÓN/USUARIO
AIRE
ACONDICIONADO
AC Smart BACnet
PBACNA000
www.lg.com
P/NO : MFL69023103
El adaptador no se incluye con el paquete AC Smart BACnet comercializado en los Estados Unidos.
8 PREPARACIÓN
NOTA
ESPAÑOL
Elemento Especificaciones
PCIMX5150D
CPU yy Núcleo ARM Cortex A8™
yy 800 MHz
MEMORIA 128 × 4 MB (DDR2 SDRAM)
Almacenamiento 4 GB (INAND FLASH)
LCD LCD TFT WSVGA (1024 × 600) de 10,2 pulgadas
Altavoz Monoaural de 300 mW
RS485 2 puertos
yy MICRO USB: 1 (para la memoria USB externa, para tareas de
servicio)
USB/SD
yy MINI USB: 1
yy Tarjeta SD: 1
DI 2 puertos
DO 2 puertos
Pantalla táctil Panel táctil tipo C
Menos de 9 segundos (ENCENDIDO/APAGADO DEL LCD), 10 segundos
Tecla de botón
(RESTABLECIMIENTO DEL SISTEMA)
ALIMENTACIÓN DC 12 V (3,33 A), AC 24 V
SO Linux
PREPARACIÓN 9
Características y funciones
A continuación se muestran las características y funciones de AC Smart BACnet.
ESPAÑOL
① ② ③ ④ ⑤ ⑥
⑨ ⑩ ⑪
<Parte inferior>
Instalación y configuración
En estos capítulos se explica cómo instalar y configurar AC Smart BACnet.
ESPAÑOL
Instalación
Para utilizar AC Smart BACnet, cree un entorno en el que AC Smart BACnet pueda establecer
comunicación con dispositivos como la unidad interior, el ERV, DI/DO, DOKIT, AWHP, UTA y I/O
Módulos. Utilice AC Smart BACnet para registrar estos dispositivos.
PRECAUCIÓN
AC Smart BACnet puede conectar hasta 128 dispositivos (incluidas las unidades internas, los ERV,
ESPAÑOL
DI/DO, DOKIT, AWHP, UTA) o 64 dispositivos (incluidas las unidades internas, los ERV, DI/DO,
A continuación se muestra un ejemplo de conexión del AC Smart BACnet con este tipo de
dispositivos.
Quantity de
Cantidad of
Device
dispositivo
Cantidad de Cantidad de
I/O módulo dispositivo
128 0 128
1 121
2 114
3 107
4 100
64
5 93
6 86
7 79
8 72
9 64
9 Cantidad
Quantitydeof
I/Omódulo
I/O Module
El AC Smart BACnet se conecta con el PI485 y utiliza la conexión RS485 para comunicar e
intercambiar información. Asigne direcciones únicas a estos dispositivos (unidades internas,
ESPAÑOL
ERV, DI/DO, DOKIT, AWHP, UTA, I/O Módulos) que se conectarán con el AC Smart BACnet. Las
direcciones son números hexadecimales, que pueden elegirse desde 00 hasta FF.
Dirección de
configuración: 11
DI/DO, DOKIT
Dirección de
configuración: 21
Dirección de
configuración: 31
... AWHP
AHU
Dirección de
configuración: 41
14 PREPARACIÓN
NOTA
ESPAÑOL
Un AC Smart BACnet puede tener un máximo de 128 unidades interiores. Si van a conectarse
ESPAÑOL
muchas unidades exteriores, conéctelas a un bus. De lo contrario, AC Smart BACnet podría
presentar fallos de funcionamiento.
<Buen ejemplo: conexión formato BUS RS485> < Mal ejemplo: conexión RS485 con formato
ESTRELLA>
NOTA
ESPAÑOL
A B A B
ODU
AHU (RS485)
PRECAUCIÓN
El cable RS485 tiene polaridad, por lo que deberá respetar la polaridad a la hora de realizar
la conexión de los cables.
5. Para poder usar las funciones de red (transmisión de correos electrónicos y control web)
proporcionadas por AC Smart BACnet deberá conectar un cable UTP al puerto LAN situado en
la parte trasera del AC Smart BACnet.
18 PREPARACIÓN
6. Conecte la alimentación.
• Para los modelos globales.
ESPAÑOL
NOTA
Puede colgar el cable de alimentación del gancho de suspensión situado debajo del
conector de alimentación.
PREPARACIÓN 19
ESPAÑOL
alimentación.
NOTA
7. Tras fijar en gancho de la parte superior del cuerpo principal a la parte superior del panel trasero
instalado en la pared, empuje hacia delante la parte superior del cuerpo principal hasta que se
ESPAÑOL
PRECAUCIÓN
NOTA
ESPAÑOL
funcionamiento de todos los dispositivos conectados (unidad interior, ventilador, DOKIT, AWHP y
AHU) si se produce una situación de emergencia en el interior del edificio. Cuando el sensor detecta
una situación de emergencia y transmite una señal de encendido al Puerto DI 1 del AC Smart
BACnet, todos los dispositivos conectados al AC Smart BACnet dejan de funcionar.
PRECAUCIÓN
en la parte inferior del panel. Utilice el teclado táctil para introducir la información.
INICIO 23
INICIO
ESPAÑOL
En este apartado se explica cómo conectar el sistema y registrar dispositivos para proceder a la
configuración del entorno (antes de usar AC Smart BACnet).
Encendido/apagado de la pantalla
A continuación se explica cómo encender y apagar la pantalla de AC Smart BACnet.
Encendido de la pantalla
La pantalla se enciende de la siguiente forma.
Apagado de la pantalla
La pantalla se apaga de la siguiente forma.
NOTA
Reinicio
Podrá reiniciar el dispositivo de la forma siguiente.
ESPAÑOL
AC Smart BACnet está, se puede controlar no sólo el equipo, sino también Web. Si introduce la
dirección IP de la unidad AC Smart BACnet en la barra de direcciones de Internet sin necesidad de
instalar otro programa, el programa de control central AC Smart BACnet calidad, servidor Web se ha
ejecutado de forma automática, para utilizar la funcionalidad de los diversos contenidos puedo.
NOTA
yy Necesitará el Adobe Flash Player se instalará para el control Web.
(Especificación recomendada : Adobe Flash Player 11)
yy Caracteres especiales (^), (‘) y(,) no están disponibles.
LG’S AC Smart BACnet AGREEMENT 25
ESPAÑOL
JMT (Joint Matching Test)
This is necessary for every independent BMS.
The case where a JMT is not necessary is where previously a successful JMT has been carried out
and the BMS system has not been updated by software or hardware changes. In the case that the BMS
has updated their system by either changes, a following JMT will be required.
BMS Engineering
Creating of the Points. This is NOT to be done by LG since it is directly related to the BMS side. The
BMS engineer is to carry out the engineering of the Point, however LG is responsible for providing the
method of how the Points are calculated.
Commission
First step, only using LG’s AC Smart BACnet , without connecting BMS. This is to be carried out by LG
engineering staff with the use of the AC Smart BACnet set up tool.
Notes
ESPAÑOL
After the LG's AC Smart BACnet agreement part, please consult with the experts of BMS.
Hub
BACnet
PQNFB17C
AC Smart BACnet
Diagnosis
1. Creating of indoor and vent points.
2. Test of all units and operations.
LG-NET
FUNCTIONAL SPECIFICATIONS
AC Smart BACnet
ESPAÑOL
Summary
The AC Smart BACnet , in response to the requests from the BMS (Building management system
which supports BACnet-ANSI/ASHRAE135 protocol), status information of A/C/vent that are
connected to the AC Smart BACnet ’s internal LG-NET will be sent in BACnet service form, and
BACnet client provides a function that transmits control command to the A/C/vent system.
Configuration of Connection
A BACnet client that supports BACnet-ANSI/ASHRAE135 protocol allows direct connection via
generally used HUBs or Ethernet. The image of its connection configuration is as shown below.
PQNFB17C
AC Smart
BACnet
ESPAÑOL
28
Unit
Point Object Name Object
Control/monitoring Inactive Active
No. (XXX : Unit address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
StartStopCommand_
1 ON/OFF (Setting) BO Stop Start
XXX
2 ON/OFF (Status) StartStopStatus_XXX BI Stop Run
3 Lock (Setting) LockCommand_XXX BO Permit Prohibit
4 Lock (Status) LockStatus_XXX BI Permit Prohibit
5 Filter Sign Filter Sign_XXX BI Off On
BACnet Point List : Indoor Unit
XXX
Objects - AC Smart BACnet /IP
SwingCommand_
9 Swing (Setting) BO Stop Run
XXX
10 Swing (Status) SwingStatus_XXX BI Stop Run
FanSpeedCommand_
11 Fan Speed (Setting) MO Low Middle High Auto
Some of IDU Points may not be supported depending on the product.
XXX
FanSpeedStatus_
12 Fan Speed (Status) MI Low Middle High Auto
XXX
13 Set Room Temperature SetRoomTemp_XXX AV °C
14 Room Temperature RoomTemp_XXX AI °C
15 Alarm Alarm_XXX BI Normal Abnormal
Unit
Point Object Name Object
Control/monitoring Inactive Active
No. (XXX : Unit address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
16 Error Code MalfunctionCode_XXX Reference LG Original Error Code
17 - - -
18 - - -
19 Set Temperature Status SetTempStatus_XXX AI °C
20 Power Distribution AccumPowerStatus_XXX AI Wattage values (Unit : 100Watt)
Set Upper Temperature SetUpperTempCommand_
27 AV °C
Setting XXX
Set Lower Temperature SetLowerTempCommand_
28 AI °C
Setting XXX
Set Upper Temperature
29 SetUpperTempStatus_XXX AI °C
Status
Set Lower Temperature
30 SetLowerTempStatus_XXX AI °C
Status
31 Mode Lock Setting ModeLockCommand_XXX BO Permit Prohibit
32 Mode Lock Status ModeLockStatus_XXX BI Permit Prohibit
33 Fan Lock Setting Fan LockCommand_XXX BO Permit Prohibit
34 Fan Lock Status FanLockStatus_XXX BI Permit Prohibit
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
29
ESPAÑOL
ESPAÑOL
30
Unit
Point Object Name Object
Control/monitoring Inactive Active
No. (XXX : Unit address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
35 Occupancy (Setting) OccupancyCommand_XXX BO Unoccupied Occupied
36 Occupancy (Status) OccupancyStatus_XXX BI Unoccupied Occupied
37 2Set Cooling Set Temperature (Setting) 2SetCoolingTempCommand_XXX AV °C
38 2Set Cooling Set Temperature (Status) 2SetCoolingTempStatus_XXX AI °C
39 2Set Heating Set Temperature (Setting) 2SetHeatingTempCommand_XXX AV °C
40 2Set Heating Set Temperature (Status) 2SetHeatingTempStatus_XXX AI °C
2Set Cooling Upper Temperature 2SetCoolingUpperLimitCommand_
41 AV °C
(Setting) XXX
42 2Set Cooling Upper Temperature (Status) 2SetCoolingUpperLimitStatus_XXX AI °C
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
35 ~ 49 points are effective, in case 2Set Auto Mode of environment setting is enabled.
FUNCTIONAL SPECIFICATIONS AC Smart BACnet 31
Remarks
ESPAÑOL
• Point NO. 1
1. The command executed is transmitted to the A/C regardless of the status of the A/C.
2. Present_Value property will not be used if a property has never been set in the past.
• Point NO. 2
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• Point NO. 7
1. T
he Present_Value property will be set to “1: Cool” as the default value if property has never
been set in the past.
2. T
he air conditioner will ignore the command to an object that does not have right to select
operation mode. Therefore, the controlled/monitored system must not use this object for the air
conditioner without the right to select operation mode.
• Point NO. 11
1. T
he A/C will disregard the command which the object which can’t select the operation mode.
Therefore, controlled/monitored system shouldn’t use the object which can’t select the operation
mode.
• Point NO. 12
1. P
resent_value property will be set to “1:Low” as the default result if the property has not been set
in the past.
• Point NO. 13
1. T
his unit is for indoor units only, and the approximate set temperature range is 18 ~ 35 °C.
2. W
hen COV registration is made, the COV will be reported the moment a temperature change of
at least 0.5 °C is detected.
• Point NO. 16
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
• Point NO. 35 ~ 49
1. T
his objects are effective, in case 2Set Auto Mode of environment setting is enabled.
ESPAÑOL
32
Heat
8 Operation Mode (Status) ModeStatus_XXX MI Auto Normal
Exchange
9 - -
10 - -
FanSpeedCommand_ Super
11 Fan Speed (Setting) MO Low High Auto
XXX High
FanSpeedStatus_ Super
12 Fan Speed (Status) MI Low High Auto
XXX High
13 - -
14 - -
15 Alarm Alarm_XXX BI Off On
Object Name Unit
Point Object
Control/monitoring (XXX : ventilation Inactive Active
No. Type
address) Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
16 Error Code MalfunctionCode_XXX AI Reference LG Original Error Code
UserModeCommand_ Quick Energy
17 User Mode(Setting) MO Heater
XXX Fresh Saving
Quick Energy
18 User Mode(Status) UserModeStatus_XXX MI Heater
Fresh Saving
19 °C
20 - - -
AC Operation Mode
21 HrvModeCommand_XXX MO Cool Auto Heat
(setting)
AC Operation Mode
22 HrvModeStatus_XXX MI Cool Auto Heat
(status)
HrvStartStopCommand_
23 AC ON/OFF (setting) BO Stop Run
XXX
24 AC ON/OFF (status) HrvStartStopStatus_XXX BI Stop Run
HrvHumidifyCommand_
25 AC Humidify (setting) BO Off On
XXX
26 AC Humidify (status) HrvHumidifyStatus_XXX BI Off On
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
33
ESPAÑOL
34 FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Remarks
• Point NO. 1
ESPAÑOL
1. The command executed is transmitted to the A/C regardless of the status of the A/C.
2. Present_Value property will not be used if a property has never been set in the past.
• Point NO. 2
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• Point NO. 5
1. T
his object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• Point NO. 6
1. D
uring a read operation of the Present_Value property, the Fliter Limit Sign Reset will be always
the same value as the Filter Limit Sign object.
2. O
nly if INACTIVE is written to the Present_Value property during a write operation, the filter sign
information resets ON signs and nothing will be executed even if ACTIVE is written.
3. This object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• Point NO. 7
1. T
he Present_Value property will be set to “1: Cool” as the default value if property has never
been set in the past.
2. T
he air conditioner will ignore the command to an object that does not have right to select
operation mode. Therefore, the controlled/monitored system must not use this object for the air
conditioner without the right to select operation mode.
• Point NO. 11
1. T
he A/C will disregard the command which the object which can’t select the operation mode.
Therefore, controlled/monitored system shouldn’t use the object which can’t select the operation
mode.
• Point NO. 12
1. P
resent_value property will be set to “1:Low” as the default result if the property has not been set
in the past.
• Point NO. 16
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
• Point NO. 17
1. This object is for vent only, and will not apply if the property has not been set in the past.
• Point NO. 18
1. T
his object is for vent only, and will not apply if the property has not been in the past.
Unit
Point Control/ Object Name Object
Inactive Active
No. monitoring (XXX : AHU address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
1 ON/OFF (Setting) StartStopCommand_XXX BO Stop Run
2 ON/OFF (Status) StartStopStatus_XXX BI Stop Run
3 Lock (Setting) LockCommand_XXX BO Permit Prohibit
4 Lock (Status) LockStatus_XXX BI Permit Prohibit
5 Filter Sign Filter Sign_XXX BI Off On
BACnet Point List : Ventilation
Operation Mode
8 ModeStatus_XXX MI Cool Dry Fan Heat
(Status)
9 - -
10 - -
11 - -
12 - -
Set Room
13 SetRoomTemp_XXX AV °C
Temperature
Room
14 RoomTemp_XXX AI °C
Temperature
15 Alarm Alarm_XXX BI Normal Abnormal
16 Error Code MalfunctionCode_XXX AI Reference LG Original Error Code
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
35
ESPAÑOL
ESPAÑOL
36
Unit
Point Object Name Object
Control/monitoring Inactive Active
No. (XXX : AHU address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
17 - -
18 - -
19 Set Temperature (Status) SetTempStatus_XXX AI °C
EmergencySensorCommand_
20 Emergency Sensor (Setting) BO Stop Run
XXX
EmergencySensorStatus_
21 Emergency Sensor (Status) BI Stop Run
XXX
22 Set Humidify (Setting) SetHumidifyCommand_XXX AV 40~60
23 Set Humidify (Status) SetHumidifyStatus_XXX AI 40~60
24 Humidify (Setting) HumidifyCommand_XXX BO Stop Run
25 Humidify (Status) HumidifyStatus_XXX BI Stop Run
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
ESPAÑOL
ESPAÑOL
38
Unit
Point Control/ Object Name Object
Inactive Active
No. monitoring (XXX : AHU address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
Heat OA Damper
49 OADamperHeatStatus_XXX AI 0~90
(Status)
Heat EA Damper EADamperHeatCommand_
50 AV 0~90
(Setting) XXX
Heat EA Damper
51 EADamperHeatStatus_XXX AI 0~90
(Status)
Heat MIX Damper MixDamperHeatCommand_
52 AV 0~90
(Setting) XXX
Heat MIX Damper
53 MixDamperHeatStatus_XXX AI 0~90
(Status)
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Remarks
ESPAÑOL
• Point NO. 1
1. The command executed is transmitted to the A/C regardless of the status of the A/C.
2. Present_Value property will not be used if a property has never been set in the past.
• Point NO. 2
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• Point NO. 5
1. T
his object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• Point NO. 6
1. D
uring a read operation of the Present_Value property, the Fliter Limit Sign Reset will be always
the same value as the Filter Limit Sign object.
2. O
nly if INACTIVE is written to the Present_Value property during a write operation, the filter sign
information resets ON signs and nothing will be executed even if ACTIVE is written.
3. This object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• Point NO. 7
1. T
he Present_Value property will be set to “1: Cool” as the default value if property has never
been set in the past.
2. T
he air conditioner will ignore the command to an object that does not have right to select
operation mode. Therefore, the controlled/monitored system must not use this object for the air
conditioner without the right to select operation mode.
• Point NO. 13
1. T
his unit is for indoor units only, and the approximate set temperature range is 18 ~ 35 °C.
2. W
hen COV registration is made, the COV will be reported the moment a temperature change of
at least 0.5 °C is detected.
• Point NO. 14
1. T
his object is for indoor units only, and reports the room temperature data measured by the
indoor units.
• Point NO. 16
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
ESPAÑOL
40
frequency XXX
4 High Pressure HighPressure_XXX AI -
5 Low Pressure LowPressure_XXX AI -
One ODU unit has a Point List as follows.
Sunction
6 SunctionTemp_XXX AI ℃
Temperature
Liquid Pipe LiquidPipeTemp_
7 AI ℃
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Temperature XXX
Heat Exchanger
8 HexTemp_XXX AI ℃
Temperature
9 Outdoor EEV OutdoorEEV_XXX AI -
10 Subcool EEV SubCoolEEV_XXX AI -
11 Hot Gas Valve HotgasValue_XXX BI Stop Run
InverterDischarge InverterDischarge
12 AI ℃
Temperature Temp_XXX
Some points may display only zero (0) value depending on the ODU product model.
AC Smart BACnet ODU Point List may not be supported depending on the product.
7 AO
(setting) XXX
Set Room Temperature SetRoomTempStatus_
8 AI
(status) XXX
Set Hot Water Temperature SetHotWaterTemp
9 AO
(setting) Command_XXX
Set Hot Water Temperature SetHotWaterTempStatus_
10 AI
(status) XXX
Set PipeOut Water SetPipeOutWater Temp
11 AO
Temperature (setting) Command_XXX
Set PipeOut Water SetPipeOutWater
12 AI
Temperature (status) TempStatus_XXX
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
41
ESPAÑOL
ESPAÑOL
42
Unit
Point Object Name Object
Control/monitoring Inactive Active
No. (XXX : AWHP address) Type
Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
Setting Temperature
13 AirWaterFlag_XXX BI Air Water
Reference (Air/Water)
Hot
14 Hot Water Only Mode HotWaterOnlyFlag_XXX BI Normal Water
Only
Current Room
15 RoomTemp_XXX AI
Temperature
16 Alarm Event Alarm_XXX BI No error Error
17 Malfunction Code MalfunctionCode_XXX AI Reference LG Original Error Code
18 HotWater On/Off (setting) HotWaterCommand_XXX BO
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
13 TempUnitCommand BO °C ˚F
(Setting)
14 Temperature Unit Setting (Status) TempUnitStatus BI °C ˚F
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
43
ESPAÑOL
44 FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Local Definition of Object ID - The instance number is a pair, this consists of the indoor unit No. and
item.
ESPAÑOL
Case Indoor
Case Vent
ESPAÑOL
Type No. No.
0 4 0 0 1 0×10001(65537) ON/OFF : setting
0 3 0 0 2 0×10002(65538) ON/OFF : status
1 4 0 1 1 0×10101(65793) ON/OFF : setting
1 3 0 1 2 0×10102(65794) ON/OFF : status
15 4 0 15 1 0×10F01(69377) ON/OFF : setting
15 3 0 15 2 0×10F02(69378) ON/OFF : status
16 4 1 0 1 0×11001(69633) ON/OFF : setting
16 3 1 0 2 0×11002(69634) ON/OFF : status
17 4 1 1 1 0×11101(69889) ON/OFF : setting
17 3 1 1 2 0×11102(69890) ON/OFF : status
31 4 1 15 1 0×11F01(73473) ON/OFF : setting
31 3 1 15 2 0×11F02(73474) ON/OFF : status
32 4 2 0 1 0×12001(73729) ON/OFF : setting
32 3 2 0 2 0×12002(73730) ON/OFF : status
33 4 2 1 1 0×12101(73985) ON/OFF : setting
33 3 2 1 2 0X12102(73986) ON/OFF : status
47 4 2 F 1 0×12F01(77569) ON/OFF : setting
47 3 2 15 2 0×12F02(77570) ON/OFF : status
Case AHU
Objects (Modbus-TCP)
ESPAÑOL
ESPAÑOL
ESPAÑOL
48
Object Name
Register Function Name Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
(XXX : Unit address)
OPERATION
1 ModeStatus_XXX Cool Dry Fan Auto Heat
MODE
2 FAN SPEED FanSpeedStatus_XXX Low Middle High Auto
SET ROOM
3 SetTempStatus_XXX °C
TEMPERATURE
Read
SetUpperTemp
4 Holding UP_SETTEMP °C
Status_XXX
Registers
Function Code : 0x03 and 0x06
SetLowerTemp
5 LO_SETTEMP °C
Status_XXX
ROOM
6 RoomTemp_XXX °C
TEMPERATURE
7 ERROR CODE MalfunctionCode_XXX Reference LG original Error Code
FUNCTIONAL SPECIFICATIONS AC Smart BACnet
OPERATION
1 ModeCommand_XXX Cool Dry Fan Auto Heat
MODE
FanSpeed
2 FAN SPEED Low Middle High Auto
Command_XXX
Write Single SET ROOM SetTemp
3 °C
Registers TEMPERATURE Command_XXX
SetUpperTemp
4 UP_SETTEMP °C
Command_XXX
SetLowerTemp
5 LO_SETTEMP °C
Command_XXX
FUNCTIONAL SPECIFICATIONS AC Smart BACnet 49
Remarks
ESPAÑOL
• StartStopStatus_XXX
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• WrStartStopCommand_XXX
1. T
he command executed is transmitted to the A/C regardless of the status of the A/C.
2. T
he Present_Value property will not be used if a property has never been set in the past.
• FanSpeedStatus_XXX
1. T
he Present_value property will be set to “1:Low” as the default value if the property has never
been set in the past.
• SetUpperTempStatus_XXX
1. T
his object is for indoor units only, and reports the set upper temperature data measured by the
indoor units.
• MalfunctionCode_XXX
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
• ModeCommand_XXX
1. T
he Present_Value property will be set to “1: Cool” as the default value if property has never
been set in the past.
2. T
he air conditioner will ignore the command to an object that does not have right to select
operation mode. Therefore, the controlled/monitored system must not use this object for the air
conditioner without the right to select operation mode.
• FanSpeed Command_XXX
1. T
he A/C will disregard the command which the object which can’t select the operation mode.
Therefore, controlled/monitored system shouldn’t use the object which can’t select the operation
mode.
• SetUpperTempCommand_XXX / SetLowerTempCommand_XXX
1. T
his unit is for indoor units only, and the approximate set upper(or lower) temperature range is
18 ~ 30 °C.
2. 1
°C is detected.
ESPAÑOL
50
Object Name
Register Function Name Inactive Active
(XXX : Ventilation address)
1 ON/OFF StartStopStatus_XXX Stop Run
2 LOCK LockStatus_XXX Permit Prohibit
3 FILTER SIGN FilterSign_XXX Off On
Coil Read
4 ALARM Alarm_XXX Stop Run
5 HRV_AC_OPER HrvStartStopStatus_XXX Stop Run
6 HRV_HUMIDIFY HrvHumidifyStatus_XXX Off On
Function Code : 0x01 and 0x05
Modbus Point List : Ventilation
ESPAÑOL
52 FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Remarks
ESPAÑOL
• StartStopStatus_XXX
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• FilterSign_XXX
1. T
his object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• StartStopCommand_XXX
1. T
he command executed is transmitted to the A/C regardless of the status of the A/C.
2. P
resent_Value property will not be used if a property has never been set in the past.
• FilterSignReset_XXX
1. D
uring a read operation of the Present_Value property, the Fliter Limit Sign Reset will be always
the same value as the Filter Limit Sign object.
2. O
nly if INACTIVE is written to the Present_Value property during a write operation, the filter sign
information resets ON signs and nothing will be executed even if ACTIVE is written.
3. This object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• FanSpeedStatus_XXX
1. P
resent_value property will be set to “1:Low” as the default result if the property has not been set
in the past.
• UserModeStatus_XXX
1. T
his object is for vent only, and will not apply if the property has not been in the past.
• MalfunctionCode_XXX
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
Object Name
Register Function Name Inactive Active
(XXX : AHU address)
1 ON/OFF StartStopStatus_XXX Stop Run
2 LOCK LockStatus_XXX Permit Prohibit
3 FILTER SIGN FilterSign_XXX Off On
4 SMOKE EmergencySensorStatus_XXX Stop Run
5 HUMIDITY HumidifyStatus_XXX Stop Run
Modbus Point List : AHU
ESPAÑOL
ESPAÑOL
54
Object Name
Register Function Name Text-0 Text-1 Text-2 Text-3 Text-4 Text-5
(XXX : AHU address)
1 MODE ModeStatus_XXX Cool Dry Fan POWSAV Heat
2 SET TEMP SetTempStatus_XXX °C
3 SUPPLY TEMP SupplyTempStatus_XXX -127~127
Function Code : 0x03
ESPAÑOL
56 FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Remarks
ESPAÑOL
• StartStopStatus_XXX
1. If there is an operation error, the Present_Value property will be set to ACTIVE regardless of
whether the A/C is in operation or not.
• FilterSign_XXX
1. T
his object supports the Intrinsic Reporting function. When the Present_Value property changes,
the corresponding Event will be transmitted if the Event has been registered.
• StartStopCommand_XXX
1. T
he command executed is transmitted to the A/C regardless of the status of the A/C.
2. P
resent_Value property will not be used if a property has never been set in the past.
• MalfunctionCode_XXX
1. T
his object’s error code descriptions should be referred to the corresponding table at the
“Reference LG original Error Code”.
• ModeCommand_XXX
1. T
he Present_Value property will be set to “1: Cool” as the default value if property has never
been set in the past.
2. T
he air conditioner will ignore the command to an object that does not have right to select
operation mode. Therefore, the controlled/monitored system must not use this object for the air
conditioner without the right to select operation mode.
FUNCTIONAL SPECIFICATIONS AC Smart BACnet 57
Local Definition of Object ID - The instance number is a pair, this consists of the indoor unit No. and
item.
ESPAÑOL
Example of Point Table
The point table below is passed to BMS, and BMS registers the object.
19 16 15 0
15 12 11 8 7 4 3 0
Case Indoor
Function Code Device No. Product No. Point Instance No. Name
1 0 0 0 0x00000 ON/OFF status
5 0 0 0 0x00000 ON/OFF Setting
1 0 1 0 0x00010 ON/OFF status
5 0 1 0 0x00010 ON/OFF Setting
1 1 0 0 0x00100 ON/OFF status
5 1 0 0 0x00100 ON/OFF Setting
3 0 0 0 0x40000 Mode status
6 0 0 0 0x40000 Mode Setting
3 0 1 0 0x40010 Mode status
6 0 1 0 0x40010 Mode Setting
3 1 0 0 0x40100 Mode status
6 1 0 0 0x40100 Mode Setting
58 FUNCTIONAL SPECIFICATIONS AC Smart BACnet
Case Vent
Function Code Device No. Product No. Point Instance No. Name
ESPAÑOL
Case AHU
Function Code Device No. Product No. Point Instance No. Name
1 0 0 0 0x08000 ON/OFF status
5 0 0 0 0x08000 ON/OFF Setting
1 0 1 0 0x08010 ON/OFF status
5 0 1 0 0x08010 ON/OFF Setting
1 1 0 0 0x08100 ON/OFF status
5 1 0 0 0x08100 ON/OFF Setting
3 0 0 0 0x48000 Mode status
6 0 0 0 0x48000 Mode Setting
3 0 1 0 0x48010 Mode status
6 0 1 0 0x48010 Mode Setting
3 1 0 0 0x48100 Mode status
6 1 0 0 0x48100 Mode Setting
FUNCTIONAL SPECIFICATIONS AC Smart BACnet 59
ESPAÑOL
period of approximately one minute will be required to recognize all the air conditioners after the
system is turn on. During this period, the following error PDU may be returned when an object
corresponding to an air conditioner is accessed.
If an attempt is made to read the Object List property of the Device object from an air conditioner
during the above period of recognition, the following error PDU will be returned, unless the air
conditioner has been recognize:
Communication error response of AC Smart BACnet , please refer to refer to AC Smart BACnet
Error Response Table on page 70AC Smart BACnet Error Response Table on page 69.
Clock Setting
The Timesynchronization service allows clock settings by the local time.
Report Function
ESPAÑOL
Event Notification
NOTES
ESPAÑOL
BIBBs
AC Smart BACnet Interoperability Building Blocks Supported(BIBBs)
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
DS-RP-A Data Sharing-ReadProperty-A □ ReadProperty ×
DS-RP-B Data Sharing-ReadProperty-B ■ ReadProperty ×
DS- Data Sharing-
□ ReadPropertyMultiple ×
RPM-A ReadPropertyMultiple-A
DS- Data Sharing-
■ ReadPropertyMultiple ×
RPM-B ReadPropertyMultiple-B
DS- Data Sharing-
□ ReadPropertyConditional ×
RPC-A ReadPropertyConditiona-A
DS- Data Sharing-
□ ReadPropertyConditional ×
RPC-B ReadPropertyConditiona-B
DS-
Data Sharing-WriteProperty-A □ WriteProperty ×
WP-A
DS-
Data Sharing-WriteProperty-B ■ WriteProperty ×
WP-B
DS- Sharing-
□ WritePropertyMultiple ×
WPM-A WritePropertyMultiple-A
DS- Data Sharing-
■ WritePropertyMultiple ×
WPM-B WritePropertyMultiple-B
SubscribeCOV ×
Confirmed
DS- ×
Data Sharing-COV-A □ COVNotification
COV-A
Unconfirmed
×
COVNotification
SubscribeCOV ×
Confirmed
DS- ×
Data Sharing-COV-B ■ COVNotification
COV-B
Unconfirmed
×
COVNotification
62 NOTES
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
ESPAÑOL
SubscribeCOV ×
Confirmed
DS- ×
Data Sharing-COVP-A □ COVNotification
COVP-A
Unconfirmed
×
COVNotification
SubscribeCOV ×
Confirmed
DS- ×
Data Sharing-COVP-B □ COVNotification
COVP-B
Unconfirmed
×
COVNotification
DS- Data Sharing-COV- Unconfirmed
□ ×
COVU-A Unsolicited-A COVNotification
DS- Data Sharing-COV- Unconfirmed
□ ×
COVU-B Unsolicited-B COVNotification
NOTES 63
ESPAÑOL
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
Confirmed
×
EventNotification
AE-N-A Alarm and Event-Notification-A □
Unconfirmed
×
EventNotification
Confirmed
×
Alarm and Event-Notification EventNotification
AE-N-I-B ■
Internal-B Unconfirmed
×
EventNotification
Confirmed
×
AE-N- Alarm and Event-Notification EventNotification
□
E-B External-B Unconfirmed
×
EventNotification
AE-
Alarm and Event-ACK-A □ AcknowledgeAlarm ×
ACK-A
AE-
Alarm and Event-ACK-B □ AcknowledgeAlarm ×
ACK-B
AE-
Alarm and Event-Summary-A □ GetAlarmSummary ×
ASUM-A
AE-
Alarm and Event-Summary-B □ GetAlarmSummary ×
ASUM-B
AE- GetEnrollment
Event-Summary-A □ ×
ESUM-A Summary
AE- GetEnrollment
Event-Summary-B □ ×
ESUM-B Summary
AE-
Alarm and Event-Information-A □ GetEventInformation ×
INFO-A
AE-
Alarm and Event-Information-B □ GetEventInformation ×
INFO-B
AE-LS-A Alarm and Event-LifeSafety-A □ LifeSafetyOperation ×
AE-LS-B Alarm and Event-LifeSafety-B □ LifeSafetyOperation ×
64 NOTES
Scheduling BIBBS
(□:Not supported,■: Support)
ESPAÑOL
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
Scheduling-A
SCHED-A (must support DS-RP-A and □
DS-WP-A)
Scheduling-Internal-B
(shall support DS-RP-B and
SCHED-
DS-WP-B) □
I-B
(shall also support ether DM-
TS-B or DS-UTC-B)
Scheduling-External-B
SCHED-
(shall support SCHED-I-B and □
E-B
DS-WP-A)
Trending BIBBS
(□:Not supported,■: Support)
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
Trending - Viewing and
T-VMT-A □ ReadRange ×
Modifying Trends-A
T-VMT- Trending-Viewing and
□ ReadRange ×
I-B Modifying Trends Internal-B
T-VMT- Trending-Viewing and
□ ReadRange ×
E-B Modifying Trends External-B
ConfirmedEvent
×
Trending - Automated Trend Notification
T-ATR-A □
Retrieval-A
edEventNoti ×
ConfirmedEvent
×
Trending - Automated Trend Notification
T-ATR-B □
Retrieval-B
edEventNoti ×
NOTES 65
ESPAÑOL
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
DM- Device Management - Who-Is ×
■
DDB-A Dynamic Device, Binding-A I-Am ×
DM- Device Management - Who-Is ×
■
DDB-B Dynamic Device, Binding-B I-Am ×
DM- Device Management - Who-Has ×
□
DOB-A Dynamic Object, Binding-A I-Have ×
DM- Device Management - Who-Has ×
■
DOB-B Dynamic Object, Binding-B I-Have ×
Device Management -
DM- DeviceCommunication
DeviceCommunication □ ×
DCC-A Control
Control-A
Device Management -
DM- DeviceCommunication
DeviceCommunication □ ×
DCC-B Control
Control-B
ConfirmedPrivate
×
Device Management - Transfer
DM-PT-A □
PrivateTransfer-A UnconfirmedPrivate
×
Transfer
ConfirmedPrivate
×
Device Management - Transfer
DM-PT-B □
PrivateTransfer-B UnconfirmedPrivate
×
Transfer
ConfirmedPrivate
×
DM- Device Management - Text Transfer
□
TM-A Message-A UnconfirmedPrivate
×
Transfer
ConfirmedPrivate
×
DM- Device Management - Text Transfer
□
TM-B Message-B UnconfirmedPrivate
×
Transfer
Device Management -
DM-TS-A □ TimeSynchronization ×
TimeSynchronization-A
Device Management -
DM-TS-B ■ TimeSynchronization ×
TimeSynchronization-B
DM- Device Management - UTCTime
□ ×
UTC-A UTCTimeSynchronization-A Synchronization
DM- Device Management - UTCTime
□ ×
UTC-B UTCTimeSynchronization-B Synchronization
66 NOTES
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
DM- Device Management -
ESPAÑOL
□ ReinitializeDevice ×
RD-A ReinitializeDevice-A
DM- Device Management -
□ ReinitializeDevice ×
RD-B ReinitializeDevice-B
AC Smart BACnet
BIBB Type Supported Initiate Execute
Service
ESPAÑOL
Establish-
Connection-To- ×
NM- Network Management - Network
□
CE-A Connection Establishment-A Disconnect-
Connection-To- ×
Network
Establish-
Connection-To- ×
NM- Network Management - Network
□
CE-B Connection Establishment-B Disconnect-
Connection-To- ×
Network
Who-Is-Router-To-
×
Network
I-Am-Router-To-
×
Network
DM- Network Management - Router I-Could-Be-Router-
□ ×
BR-A Configuration-A To-Network
Initialize-Routing-
×
Table
Initialize-Routing-
×
Table-Ack
Who-Is-Router-To-
× ×
Network
I-Am-Router-To-
× ×
NM- Network Management - Router Network
□
RC-B Configuration-B Initialize-Routing-
×
Table
Initialize-Routing-
×
Table-Ack
68 NOTES
Object_Identifier BACnetObjectIdentifier R
Object_Name CharacterString R
Object_Type BACnetObjectType R
Present_Value Unsigned R1
Description CharacterString O
Device_Type CharacterString O
Status_Flags BACnetStatusFlags R
Event_State BACnetEventState R
Reliability BACnetReliability O2
Out_Of_Service Boolean R
Number_Of_States Unsigned R
BACnetARRAY[N] of
State_Text O
CharacterString
Time_Delay Unsigned O3
Notification_Class Unsigned O3
Alarm_Values List of Unsigned O3
Fault_Values List of Unsigned O3
Event_Enable BACnetEventTransitionBits O3
Acked_Transitions BACnetEventTransitionBits O3
Notify_Type BACnetNotifyType O3
BACnetARRAY[3] of
Event_Time_Stamps O3
BACnetTimeStamp
ESPAÑOL
Out_Of_Service Boolean R
Number_Of_States Unsigned R
BACnetARRAY[N] of
State_Text O
CharacterString
Priority_Array BACnetPriorityArray R
Relinquish_Default Unsigned R
Time_Delay Unsigned O1
Notification_Class Unsigned O1
Feedback_Value Unsigned O1
Event_Enable BACnetEventTransitionBits O1
Acked_Transitions BACnetEventTransitionBits O1
Notify_Type BACnetNotifyType O1
BACnetARRAY[3] of
Event_Time_Stamps O1
BACnetTimeStamp
Profile_Name CharacterString O
70 NOTES
Error PDU
Error PDU Error Class Error Code
Reading of the object list during the initialization of
Device(0) Configuration_In_Progress(2)
the LG-NET
Request to access to an object not installed. Object(1) Unknown_Object(31)
Request to access to a property not installed. Property(2) Unknown_Property(32)
Request to write to a prohibited area. Property(2) Write_Access_Denied(40)
Request to write in a format different from the
Property(2) Invalid_Datatype(9)
property.
Request to access to a specified index outside the
Property(2) Invalid_Array_Index(42)
array index range.
Request to write a value outside the permissible
Property(2) Value_Out_Of_Range(37)
range.
A COV registration request of more than 10
Resource(3) Other(0)
registration items.
An Event registration request of more than 10 No_Space_To_Add_List_
Resource(3)
registration items. Element(19)
Request for the deletion of an element not existing
Service(5) Other(0)
in the list.
Request for the execution of the AddListElement/
RemoveListElement for a property that is not of Service(5) Property_Is_Not_List(22)
List type.
Reject PDU
Reject PDU Reject Reason
A propertyID or value overflow or underflow occurred
Inconsistent_Parameter(2)
during WritePropertyMultiple operation.
The type of parameter for the execution of the service is
Invalid_Parameter_Data_Type(3)
different in type.
An error was detected during tag decoding. Invalid_Tag(4)
A parameter shortage occurred during the execution of
Missing_Required_Parameter(5)
the service.
Too many arguments for the execution of the service. Too_Many_Arguments(7)
An attempt to execute an unsupported service with
Unrecognized_Service(9)
confirmation.
NOTES 71
Abort PDU
Reject PDU Reject Reason
ESPAÑOL
Unable to process due to too many requests beyond the
Buffer_Overflow(1)
capacity.
The processing of segments was aborted because an
Invalid_APDU_In_This_State(2)
expected APDU was received.
The response side does not support the segment. Segmentation_Not_Supported(4)
72 CONSEJO
CONSEJO
ESPAÑOL
Códigos de control
El AC Smart BACnet puede mostrar los siguientes códigos de control durante su funcionamiento
Código de
Descripción
control
S Aparece cuando el estado del dispositivo ha cambiado debido al control
M Aparece cuando ha cambiado la configuración del sistema
E Aparece cuando hay un error
Códigos de error
A continuación se indican los códigos de error utilizados en el AC Smart BACnet.
Error de dispositivo interior, ERV o ERV DX, AWHP (Kit hidro), UTA
Código
Dispositivo interior ERV o ERV DX AWHP (Kit hidro) UTA
de error
0 No hay error No hay error No hay error
Mal
Mal funcionamiento
Sensor interior (Aire) funcionamiento
1 del sensor de
abierto/cerrado del termómetro de
entrada de aire
aire interior
Mal Error (tubería
Mal funcionamiento
Sensor interior funcionamiento de entrada)
del termómetro
2 (tubería de entrada) del termómetro del sensor
de entrada de
abierto/cerrado de entrada de interior PCB de
refrigerante
refrigerante comunicación
El control remoto
Mal
Mal funcionamiento Mal funcionamiento no funciona
3 funcionamiento
del control remoto del control remoto durante 3 minutos
del control remoto
o más.
El PCB de
Mal funcionamiento Mal funcionamiento
comunicación no
4 de la bomba de de la bomba de
funciona durante 3
desagüe desagüe
minutos o más.
CONSEJO 73
Código
Dispositivo interior ERV o ERV DX AWHP (Kit hidro) UTA
de error
ESPAÑOL
Error de
Error de
Error de Error de comunicación
comunicación
5 comunicación comunicación (PCB de
(interior ↔
(interior ↔ exterior) (interior ↔ exterior) comunicación ↔
exterior)
exterior)
Mal
Mal funcionamiento Error (tubería de
Sensor interior funcionamiento
del termómetro salida) del sensor
6 (tubería de salida) del termómetro
de salida de interior PCB de
abierto/cerrado de salida de
refrigerante comunicación
refrigerante
7 Operación atípica Operación atípica Operación atípica
Operación del
Mal
control de humo
funcionamiento
8 mediante la
del termómetro de
detección de
agua caliente
humo.
ERROR EEPROM ERROR EEPROM ERROR EEPROM
9
(unidad interior) (unidad interior) (unidad interior)
BLOQUEO del Bloqueo del
10 ventilador interior ventilador interior
(error de operación) (error de operación)
Error de
comunicación
11
HHU/caldera
(HHU)
Error del sensor
Error de caldera
12 a media tubería
(HHU)
interior
La temperatura
(ERV, suministro
Sensor de bloqueo Error del sensor
de aire, aire
13 del terminal de la de temperatura
exterior, Mixto)
resistencia (A-PAC) del calor solar
está fuera del
rango aceptable.
La humedad (ERV,
Error de operación
suministro de aire,
del interruptor de
14 aire exterior) está
flujo de la unidad
fuera del rango
interior
aceptable
74 CONSEJO
Código
Dispositivo interior ERV o ERV DX AWHP (Kit hidro) UTA
de error
ESPAÑOL
Error de
comunicación
Sobrecalentamiento El valor de CO₂
O-ROTOR
15 de la tubería de está dentro del
(controlador del
agua rango aceptable
VENTILADOR
BLDC)
La presión
Error simultáneo (cambio de
del sensor de presión, presión
16
temperatura estática) está
AWHP fuera del rango
aceptable
La velocidad
Error del sensor
(ERV y flujo de
Sensor de salida de de temperatura
17 suministro de aire)
aire del ERV DX de la entrada de
está fuera del
agua
rango aceptable.
Error del sensor
Sensor de retorno
18 de temperatura de
de aire del ERV DX
la salida de agua
Error de Error del sensor
comunicación de temperatura de
19 PCB principal del la salida del agua
ERV DX ← PCB de la resistencia/
secundario eléc
Error de
comunicación
Error de
20 PCB principal del
resistencia/eléc
ERV DX → PCB
secundario
CONSEJO 75
ESPAÑOL
de error
21 DC máximo
22 Max ct (CT 2): error actual máximo
23 Voltaje de conexión DC (bajo)
24 SW alto voltaje/placa de calor
25 Infravoltaje/sobrevoltaje
26 Error de posición de la computadora DC
27 Error de PSC
28 Voltaje de conexión DC (alto)
29 Sobrevoltaje en la computadora
30 Subida de la temperatura de descarga del compresor n.º 2 de velocidad estática
31 Error de CT (corriente baja)
32 Error de temperatura de descarga del inversor (alta)
33 Subida de la temperatura de descarga del compresor n.º 1 de velocidad estática
34 Subida de alta tensión
35 Bajada de baja tensión
36 Error de proporción de baja compresión
37 Se superó el límite proporcional de compresión
39 Error de comunicación (inversor ↔ PFC)
40 Sensor CT de inversor abierto/cerrado
41 Sensor de temperatura de descarga del inversor abierto/cerrado
42 Sensor de baja tensión abierto/cerrado
43 Sensor de temperatura del intercambiador de calor (parte superior)
44 Sensor de temperatura de aire exterior abierto/cerrado
45 Sensor de tubería exterior (parte superior) abierto/cerrado
46 Sensor de temperatura de aspiración del compresor abierto/cerrado
Error del sensor de temperatura de descarga del compresor n.º 1 de velocidad
47
estática
Sensor de temperatura del intercambiador de calor (parte inferior) (SUPER3: error
48
del sensor de temperatura de descarga del compresor n.º 2 de velocidad estática)
49 Error del sensor de tensión exterior (SUPER3: error del sensor de temperatura IPM)
50 Fase que falta en potencia trifásica exterior
51 Error de sobrecapacidad (se superó el límite de capacidad de la unidad interior)
52 Error de comunicación (placa del inversor → placa principal)
76 CONSEJO
Código
Descripción
de error
ESPAÑOL
Código
Descripción
de error
ESPAÑOL
86 Error PCB EEPROM principal
87 Error PCB EEPROM ventilador
88 Error PCB EEPROM PFC
89 Error de comunicación del distribuidor de tipo extraíble
Código
Descripción
de error
ESPAÑOL
Código
Descripción
de error
ESPAÑOL
Error del sensor de entrada de sobrerrefrigeración de la unidad de recuperación de
141
calor
Error del sensor de salida de sobrerrefrigeración de la unidad de recuperación de
142
calor
143 Error de comunicación de la unidad de recuperación de calor
144 Reserva 1 de la unidad de recuperación de calor
145 Reserva 2 de la unidad de recuperación de calor
146 Reserva 3 de la unidad de recuperación de calor
147 Reserva 4 de la unidad de recuperación de calor
148 Reserva 5 de la unidad de recuperación de calor
176 Sobrecorriente/infracorriente del compresor 1 de velocidad estática ESCLAVO2
177 Sobrecorriente/infracorriente del compresor 2 de velocidad estática ESCLAVO2
178 Sobrecorriente/infracorriente del compresor 1 de velocidad estática ESCLAVO3
179 Sobrecorriente/infracorriente del compresor 2 de velocidad estática ESCLAVO3
180 Anticongelante (refrigeración de agua)
181 Error del sensor de temperatura de agua (refrigeración de agua)
182 Error de comunicación Sub Micom
183 Error del suministro de aceite
184 Error del sensor de temperatura de la tubería de aceite del inversor
185 Error del sensor de temperatura de la tubería de aceite n.º 1 estática
186 Error del sensor de temperatura de la tubería de aceite n.º 2 estática
193 Subida de temperatura de la placa de calor de la placa del ventilador
194 Error del sensor de temperatura de la placa de calor de la placa del ventilador
Código
Descripción
de error
ESPAÑOL
Código
Descripción
de error
ESPAÑOL
Error de comunicación (no hay señal de la unidad exterior durante 3 min desde la
224
unidad6 HR)
Error del sensor de la tubería de fluido (sensor de la tubería de fluido de la unidad7
225
HR abierto/cerrado)
Error del sensor de entrada de sobrerrefrigeración (sensor de entrada de
226
sobrerrefrigeración de la unidad7 HR abierto/cerrado)
Error del sensor de salida de sobrerrefrigeración (sensor de salida de
227
sobrerrefrigeración de la unidad7 HR abierto/cerrado)
Error de comunicación (no hay señal de la unidad exterior durante 3 min desde la
228
unidad7 HR)
Error del sensor de la tubería de fluido (sensor de la tubería de fluido de la unidad8
229
HR abierto/cerrado)
Error del sensor de entrada de sobrerrefrigeración (sensor de entrada de
230
sobrerrefrigeración de la unidad8 HR abierto/cerrado)
Error del sensor de salida de sobrerrefrigeración (sensor de salida de
231
sobrerrefrigeración de la unidad8 HR abierto/cerrado)
Error de comunicación (no hay señal de la unidad exterior durante 3 min desde la
232
unidad8 HR)
Error del sensor de la tubería de fluido (sensor de la tubería de fluido de la unidad9
233
HR abierto/cerrado)
Error del sensor de entrada de sobrerrefrigeración (sensor de entrada de
234
sobrerrefrigeración de la unidad9 HR abierto/cerrado)
Error del sensor de salida de sobrerrefrigeración (sensor de salida de
235
sobrerrefrigeración de la unidad9 HR abierto/cerrado)
Error de comunicación (no hay señal de la unidad exterior durante 3 min desde la
236
unidad9 HR)
Además del código fuente, podrá descargar las condiciones de las licencias, exención de
responsabilidad de la garantía y avisos de copyright.
LG Electronics también le proporcionará código abierto en CD-ROM por un importe que cubre los
gastos de su distribución (como el soporte, el envío y la manipulación) previa solicitud por correo
electrónico a opensource@lge.com. Esta oferta es válida durante tres (3) años a partir de la fecha
de adquisición del producto.
ver. 1.0.0