Beruflich Dokumente
Kultur Dokumente
A10VSO
(US-Version)
Contents Features
Type code for standard program 2 –– Variable axial piston pump in swash plate design for hydro-
static drives in open circuit systems
Technical data 4
–– The flow is proportional to the drive speed and the displace-
Technical data – Standard rotary group 6
ment
Technical data – High-Speed-rotary group 7
–– The flow can be steplessly varied by adjustment of the swash
DG – Two point control, directly operated 10 plate angle.
DR – Pressure control 11 –– Hydrostatic support of the cradle bearings
DRG – Pressure control remotely operated 12 –– Port for pressure transducer in pump outlet
DRF/DRS – Pressure and flow control 13 –– Low noise level
LA... – Pressure, flow and power control 14 –– Low pressure pulsation
ED – Electro-hydraulic pressure control 15 –– High efficiency
ER – Electro-hydraulic pressure control 16 –– Highly resistant against cavitation,
sudden drop in suction pressure and housing pressure spikes
Dimensions size 45 to 180 17
–– Universal through drive
Dimensions through drive 32
Summary mounting options 35
Combination pumps A10VSO + A10VSO 36
Connector for solenoides 37
Electronic controls 37
Installation notes 39
General information 40
2/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Seals
07 FKM (Fluoro-rubber) l l l l l V
Drive shaft 045 071 100 140 180
Parallel shaft with key to ISO 3019-1 (SAE J744), not for through drive l l l l l K
08 Splined shaft standard shaft l l l l l S
ANSI B92.1a similar to shaft „S“ however for higher input torque l l – – – R
Mounting flange
09 ISO 3019-1 - 4-bolt D
Ports for service lines1)
SAE-flange on top and at the bottom , opposite sides,
l l l l l 72U
10 UNF fixing thread, with universal through drive
Like 72U, with pulsation damping, not for High-Speed l l l l m 82U
Through drive
Without through drive, with through drive shaft, without shaft coupler, without adapter flange,
– ▲ ▲ ▲ – 99
with cover properly closed
Without through drive, with through drive shaft, without shaft coupler, without adapter flange
l l l l l 00
with cover properly closed ( for new applications)
Flange ISO 3019-12) Coupler for splined shaft3)
Diameter Diameter
82-2 (A) 5/8 in 9T 16/32DP l l l l l 01
3/4 in 11T 16/32DP l l l l l 52
11
101-2 (B) 7/8 in 13T 16/32DP l l l l l 68
101-2 (B) 1 in 15T 16/32DP l l l l l 04
127-4 (C) 1 in 15T 16/32DP l l l l l E2
1 1/4 in 14T 12/24DP – l l l l 15
127-2 (C) 1 1/2 in 17T 12/24DP – – l l l 24
152-4 (D) 1 1/2 in 17T 12/24DP – – l l l 96
1 3/4 in 13T 8/16DP – – – l l 17
Rotary group version
Standard-rotary group (noise-optimized for n = 1500/1800 rpm) l l l l l E
12
High Speed (only with port plate 72U) l l l l m S
Solenoid connectors
Without l l l l l 0
13
HIRSCHMANN-plug - without suppressor diode (only for ED/ER control) l l l l l H
= available m = on request ▲ = not for new applications – = not available
1) See RE 95581 universal through drive
2) 2-bolt: mounting pump series 31; 4-bolt: mounting pump series 32. See page 35 Summary mouting options
3) Coupler for splined shaft to ANSI B92.1a (drive shaft allocation to SAE J744)
4/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Technical data
Fluids Notes on the selection of the hydraulic fluid
Prior to project design, please see our technical data sheets In order to select the correct fluid, it is necessary to know the
RE 90220 (mineral oil) and RE 90221 (environmentally ac- operating temperature in the tank (open circuit) in relation to
ceptable fluids) for detailed information on fluids and operating the ambient temperature.
conditions. The fluid should be selected so that witin the operating tempe-
When using environmentally acceptable hydraulic fluids, rature range, the viscosity lies within the optimum range (nopt),
the limitations regarding technical data and seals must be see shaded section of the selection diagram. We recommend
observed. Please contact us. to select the higher viscosity grade in each case.
nmin = 60 SUS (10 mm2/s) If the above conditions cannot be met, due to extreme opera-
for short periods (t ≤ 1 min) ting parameters please consult us.
at max. perm. fluid temperature of 195 °F (90 °C). Filtration of the fluid
Please note that the max. leakage fluid temperature of 195 °F The finer the filtration the better the fluid cleanliness class, and
(90 °C) is also not exceeded in certain areas (for instance bea- the longer the service life of the axial piston pump.
ring area).The fluid temperature in the bearing area is approx.
7 °F (5 K) higher than the average leakage fluid temperature. In order to guarantee the functional reliability of the axial piston
unit it is necessary to carry out a gravimetric evaluation of the
nmax = 7500 SUS (1000 mm2/s) fluid to determine the particle contamination and the cleanli-
for short periods (t ≤ 1 min) ness class acc. to ISO 4406. A cleanliness class of at least
on cold start 20/18/15 is necessary.
(p ≤ 435 psi (30 bar), n ≤ 1800 rpm, At very high fluid temperatures (195 °F (90 °C) to max. 239 °F
tmin = -13 °F (-25 °C)) (115 °C)) a cleanliness class of at least 19/17/14 to ISO 4406
At temperatures between -40 °F (-40 °C) and -13 °F (-25 °C) is necessary.
special measures are required, please consult us for further If above classes cannot be maintained, please consult us.
information.
For detailed information on operation with low temperatures
see data sheet RE 90300-03-B.
Selection diagram
-40° -4° 32° 68° 104° 140° 176°
-40° -20° 0° 20° 40° 60° 80°
7400 1600 1600 7400
4600 1000
3000 600
2000 400
VG 68
1000
VG
VG 22
VG 32
VG 46
200
10
500 100
0
Viscosity n [SUS (mm2/s)]
300 60
200 40 36 170
100 20
80 16 80
60 10
Technical data
Operating pressure range Definition
Pressure at outlet port (pressure port) B Nominal pressure pnom
The nominal pressure corresponds to the maximum design
Nominal pressure pnom _________ 4000 psi (280 bar) absolute
pressure.
Maximum pressure pmax _ ______ 5100 psi (350 bar) absolute
Maximum pressure pmax
Individual operating period_________________________ 2.5 ms
The maximum pressure corresponds to the maximum pressure
Total operating period _____________________________ 300 h
within the individual operating period. The total of the individual
Minimum pressure(high pressure side) ___ 145 psi (10 bar)2) operating periods must not exceed the total operating period.
Rate of pressure change RA max_ 235000 psi/s (16000 bar/s) Minimum pressure (in pump outlet)
Minimum pressure in the pump outlet side (port B) that is
pnom required in order to prevent damage to the axial piston unit.
Pressure p
Maximum pressure pabs max ________ 145 psi (10 bar)1) absolute Time t
Inlet pressure high-speed-rotary group Total operating period = t1 + t2 + ... + tn
Minimum pressure pabs min ____________ 15 psi (1 bar) absolute
Maximum pressure pabs max ________ 145 psi (10 bar)1) absolute
1) Other values on request
Case drain pressure
2) Lower pressure, depends on timeframe, please consult us.
Maximum permissible case drain pressure (at port L, L1):
Maximum 7 psi (0.5 bar) higher than the inlet pressure at port
S, however not higher than 29 psi (2 bar) absolute.
pL max abs _________________________________ 29 psi (2 bar)1)
6/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Important
Exceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational-
service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simulati-
on and comparison with the permissible data.
Determination of size
Important
Exceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational
service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simulati-
on and comparison with the permissible data.
8/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Technical data
Permissible radial and axial forces on the drive shaft
Size NG 45 71 100 140 180
Radial force maximum Fq
Note
The direction of the permissible axial force:
+ Fax max = Increase of bearing service life
– Fax max = Reduction of bearing service life (avoid)
TE
1. Pumpe
1. Pumpe 2. Pumpe
2. Pumpe
TD
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 9/40
Technical data
Drive power and flow
Fluid: hydraulic oil ISO VG 46 DIN 51519, t= 122 °F (50°C)
Drive power P
(60) (30) 40 60 qV
220 110
PqV max 140
Flow qV
Drive power P
(0) 0 (0) 160 80
40 PqV max 100
0 50 100 150 200 250 280 (bar)
140 70
Flow qV
0 500 1000 1500 2000 2500 3000 3500 4000 psi
120 60 80
30
Operating pressure p 100 50
60
80 20 40
Size 71 60 30 40
_ _ _ __n = 1500 rpm 40 10 PqV 0
20
20
20 10
______ n = 1800 rpm
0 0 0 0
(L/min) gpm (kW) HP 0 50 100 150 200 250 280 (bar)
160 40 80 0 500 1000 1500 2000 2500 3000 3500 4000 psi
100
140 70 Operating pressure p
120 30 qV 60 80
Size 180
Drive power P
100 50
Drive power P
50
______ n = 1800 rpm 180 90 120
200 100
50 120 60 80
30
180 90 120 100 50
qV 60
160 80 80 40
40 100 20
140 70 60 30 40
PqV max
120 60 80
Flow qV
30 40 10 20
PqV 0 20
100 50 20 10
Drive power P
60
80 20 40 0 0 0 0
0 50 100 150 200 250 280 (bar)
60 30 40
0 500 1000 1500 2000 2500 3000 3500 4000 psi
40 10 20
PqV 0 20
20 10
Operating pressure p
0 0 0 0
0 50 100 150 200 250 280 (bar)
0 500 1000 1500 2000 2500 3000 3500 4000 psi
Operating pressure p
10/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
L1 S
(50) 725
(0) 0
0 725 2000 3050 4000 psi Port for
(0) (50) (70) (140) (210) (280) (bar) B Service line
Operating pressure pB S Inlet
L, L1 Case drain (L1 plugged)
X Control pressure
MB Measuring operating pressure
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 11/40
DR – Pressure control
The DR-pressure control limits the maximum pressure at the Schematic
pump outlet within the pump control range. The pump therefo-
re supplies only the amount of fluid as required by the actua-
tors. This maximum pressure level can be set steplessly at the
control valve.
Static characteristic L MB B
(at n1 = 1500 rpm; tfluid = 122 °F (50°C))
Setting range
35 510 L1 S
Port for
B Service line
S Inlet
L, L1 Case drain (L1 plugged)
MB Measuring operating pressure
Controller data
Hysteresis and repeatibility ___________ ∆p max. 45 psi (3 bar)
Pressure rise, max
The standard setting of the DRG control spool is 290 psi (20
bar). This results in a pilot oil flow to the relief valve of approx.
0.4 gpm (1,5 L/min). If another setting is required please state
in clear text. The setting range is from 145 - 319 bar (10-22
bar).
As a separate relief valve we can recommend: L B
DBDH 6 (hydraulic) to RA 25402 or
DBETR-SO 381 with orifice dia. 0.03 in (0.8 mm) in P
(electric) to RA 29166.
The maximum length of piping should not exceed 6.5 ft (2 m).
Static characteristic
(at n1 = 1500 rpm; tfluid = 122 °F (50°C))
(bar) psi L1 S
Hysteresis and pressure rise ∆pmax
280 4000
Operating pressure pB
Setting range
Port for
B Service line
S Inlet
L, L1 Case drain(L1 plugged)
X Control pressure
20 290
MB Measuring operating pressure
Controller data
Hysteresis and repeatability___________ ∆p max. 45 psi (3 bar)
Pressure rise, max
Note
The DRS-valve version has no connection between X and the
tank (pump housing).
Unloading the LS-pilot line must be possible in the valve sys-
tem. L MB B
Because of the flushing function sufficient unloading of the
X-line must also be provided.
Static characteristic
Flow control at n1 = 1500 rpm; tfluid = 122 °F (50°C))
Hysteresis and pressure rise ∆pmax
(bar) psi
(280) 4000
Operating pressure pB
Setting range
L1 S
X
(250) 3600
LA9
(200) 2900
LA8
B
(150) 2200
LA7 Schematic (LAXDG) with pressure cut off, remotely operated
(100) 1450
LA6 X
(50) 725
LA5
(0) 0
not included in
0
Flow qV [%] 100 B
supply
∆qV
not included in
LA9 X
supply
LA8
X
MB B
LA7
Schematic (LAXDS) with pressure and flow control
LA6 X
LA5
0 100
Flow qV [%] not included in
L B
supply
Port for
B Service line
S Inlet
L, L1 Case drain fluid (L1 plugged) L1 S
X Control pressure
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 15/40
Standby
350 24
to maintain this set pressure level.
320 22
The pump output flow matches the required input flow to the 290 20
actuators. The desired pressure level can be set steplessly by 260 18
varying the solenoid current.
230 16
When the solenoid current signal drops towards a zero value, 200 14
the maximum output pressure is limited by an adjustable me- bar 120 140 160 180 200 220 240 260 280
psi 1750 2000 2350 2600 2900 3200 3500 3700 4100
chanical pressure cut off (secure fail safe function in case of a
loss of power e.g. for use as fan drives). Maximum pressure setting
The response time characteristic of the ED-control was opti- Schematic ED..
mized for the use as a fan drive system.
When ordering, state the type of application in clear text.
ED De-activation of B
control
Max. adjustable
control pressure
2000 (140)
4100 (280)
Setting range
5070 (350)
Operating pressure p [psi (bar)]
4100 (280)
L1 S
3600 (250)
Max. adjustable
control pressure
2200 (150) Port for
B Service line
Min. adjustable S Suction line
725 (50)
control pressure L, L1 Caise drain (L1 plugged)
0
0 1
Amperage I/Imax
Nom. resistence
5,5 Ω 22,7 Ω
(at 68 °F (20 °C))
Setting range
Flow qv [L/min]
max min
Control data
Standby standard setting 200 psi (14 bar), other values on
request.
Hysteresis and pressure rise ∆p < 60 psi (4 bar).
Pilot flow consumption: 0.79 to 1.19 gpm (3 to 4,5 L/min).
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 17/40
DR – Pressure control
B
.5)
DIA 0.56
0.35(9) 3.74 (95) MB 89
(Ø14.3)
2(
0.3
Flange 0.25 (6.3) 3.5
1.57 (40)
9(
ISO 3019-1
10
3.58 (91)
)
2.40 (61)
X
57
(Ø127 - 00.063 )
4.46 (113.2)
5.75 (146)
.5°
DIA 5.0000
4.9975
3.09 (78.5)
3.58 (91)
0.61 (15.5) L1 5.08 (129)
S
1.77 (45) 4.46 (113.2)
7.24 (184) 5.75 (146)
9.53 (242) 0.95 (24) 3.68 (93.5) 5.75 (146)
Valve mounting for
counter clockwise
rotation
0.98 (25)
1.30 (33)
S 1.03 (26.2)
2.06 (52.4)
B
2.75 (69.9)
DIA 1.57
(Ø40)
0.47 (12)
MB
1.41 (35.7)
G 1/4"
1.18
(to mounting flange face) 7.36 (30)
(187)
18/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Drive shaft
S Splined shaft 1 in 15T 16/32DP1) R Splined shaft 1 in 15T 16/32DP1)2) K Parallel keyed shaft
(SAE J744 - 25-4 (B-B)) (SAE J744 - 25-4 (B-B)) (ISO 3019-1)
1.67 + 0.3
1.65 (42 0.0 )
1.50 (38)
1/4-20UNC-2B3)4)
1.54 (39)
1/4-20UNC-2B3)4)
(ø25.4 -0.03)
0.63 (16)
0.9988
DIA 1.0000
0.63 (16) 0.63 (16)
1/4-20UNC-2B 3)4)
0.20 (5) 0.20(5)
0.09
(2.2)
1.81 (45.9)
Ports
Designation Port for Standard Size4) Maximum pressure State
[psi (bar)]5)
B Service line SAE J518 1 in 5100 (350) O
Connection threads ASME B1.1 3/8-16UNC-2B; 0.71 (18) deep
S Inlet SAE J518 1 1/2 in 145 (10) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.87 (22) deep
L Case drain fluid ISO 119267) 7/8-14UNF-2B; 0.51 (13) deep 30 (2) O6)
L1 Case drain fluid ISO 119267) 7/8-14UNF-2B; 0.51 (13) deep 30 (2) X6)
X Load-Sensing pressure ISO 11926 7/16-20 UNF-2A; 12 deep 5100 (350) O
X Control press. DG control DIN 3852 G 1/4 in ; 12 deep 1600 (120) O
MB Measuring pressure in B DIN 38527) G 1/4; 12 deep 5100 (350) X
1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5
2) Spline according to ANSI B92.1a, run out of spline is a deviation from standard.
3) Thread according to ASME B1.1
4) For the maximum tightening torques the general information on page 40 must be observed.
5) Depending on the application, momentary pressure spikes can occur. Consider this when selecting measuring devices and
fittings.
6) Depending on the installation postion, L or L1 must be connected (see also page 38, 39).
7) The spot face can be deeper than as specified in the standard.
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 19/40
DG LA.D.
Two point control, directly operated Pressure, flow and power control
7.95 (202)
7.20 (182.8) X
4.50 (114)
0.12 (3)
1.57 (40)
X
X
DRG ED7./ER7.
Pressure control, remotely operated Electro hydraulic pressure control
6.46 (164)
X
(140)
5.51
X
X
DRF/DRS
Pressure and flow control
6.46 (164)
X
X
4.88 (124)
5.55 (141)
Valve mounting for
counter clockwise
rotation
1) ER7.: 6.93 in (176 mm) when using a sandwich plate pressure control.
20/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
DR – Pressure control
1.57
(40)
0.5
3.03
3 (1
4.51(114.5)
(77)
0
5.75 (146)
3.5
)
3)
6 (10
4.0
(90.5)
5.0000
3.56
DIA
S 4.51 (114.5)
0.71 (18) L1 5.75 (146)
2.09(53) 4.13 (105) 5.41(137.5)
8.54 (217) 0.47 (12) Valve mounting for
6.06 (154)
counter clockwise
10.91 (277) 0.94 (24) rotation
0.98(Ø25)
B
2.06(52.4)
S
(Ø50)
(77.8)
3.06
1.96
1.03(26.2) 1.69
(42.9)
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 21/40
Drive shaft
S Splined shaft 1 1/4 in 14T R Splined shaft 1 1/4 in 14T K Parallel keyed shaft
12/24DP1) (SAE J744 - 32-4 (C)) 12/24DP1)2) (SAE J744 - 32-4 (C)) (ISO 3019-1)
1.87 (47.5)
1.87 (47.5)
5/16-18UNC-2B 3)4)
1.63 (41.3)
5/16-18UNC-2B3)4)
0.75 (19)
0.75 (19) 0.65 (19)
0.24 (6) 0.12 (3)
0.24 (6)
5/16-18UNC3), 4)
1.38 (35.3 -0.2)
(ø31.75 -0.03)
DIA 1.2500
1.2488
1.39
Usable spline 1.49 (38)
lenght
1.56 2.18 (55.4) 2.19 (55.5)
(39.5)
2.18 (55.4)
Ports
Designation Port for Standard Size4) Maximum State
pressure [psi (bar)]5)
B Service line SAE J518 1 in 4000 (350) O
Connection threads ASME B1.1 3/8-16UNC2-B; 0.71 (18) deep
S Inlet SAE J518 2 in 145 (10) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.79 (20) deep
L Case drain fluid ISO 119267) 7/8-14UNF-2B ; 0.47 (12) deep 30 (2) O6)
L1 Case drain fluid ISO 119267) 7/8-14UNF-2B ; 0.47 (12) deep 30 (2) X6)
X Load-Sensing pressure ISO 11926 7/16-20 UNF-2A; 0.47 (12) deep 4000 (350) O
X Control pressure DG-control DIN 3852 G 1/4 in ; 0.47 (12) deep 1800 (120) O
MB Measuring pressure in B DIN 38527) G 1/4; 0.47 (12) deep 4000 (350) X
1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5
2) Spline according to ANSI B92.1a, run out of spline is a deviation from standard.
3) Thread according to ASME B1.1
4) For the maximum tightening torques the general information on page 40 must be observed.
5) Depending on the application, momentary pressure spikes can occur. Consider this when selecting measuring devices and
fittings.
6) Depending on the installation postion, L or L1 must be connected (see also page 38, 39).
7) The spot face can be deeper than as specified in the standard.
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
22/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
DG LA.D.
Two point control, directly operated Pressure, flow and power control
9.91 (251.6)
0.47 (12)
8.35 (212)
X
0.12 (3)
1.57 (40)
4.98 (126.5)
X
X 4.63
5.41 (137.3)
(117.5)
Valve mounting for 6.06 (153.8)
4.78
(121.5) counter clockwise
Valve mounting for rotation
counter clockwise
rotation
DRG ED7./ER7.
Pressure control, remotely operated Electro hydraulic pressure control
7.60 (193)
X
5.51 (140)
X
1.57 (40)
4.22 (107.2)
DRF/DRS
Pressure and flow control
7.60 (193)
X
1.57 (40)
4.22 (107.2)
5.41 (137.3)
6.06 (153.8)
Valve mounting for
counter clockwise
rotation
1) ER7.: 7.44 in (189 mm) when using a sandwich plate pressure control.
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 23/40
DR – Pressure control
Ø0.79 (20)
5°
0.5 )
6.36 (161.6)
7.87 (200)
(15
57.
9
4.15 (105.5)
6.0000
2.63 (66.7)
3.50 (88.9)
S B
DIA 1.26 (Ø32)
1.25 (31.8)
2.00
(50.8)
24/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Drive shaft
S Splined shaft 1 1/2 in 17T 12/24DP1) K Parallel keyed shaft (ISO 3019-1)
(SAE J744 - 38-4 (C-C)) 2.13 (54)
2.13 (54) 2.11 (53.6)
7/16-14UNC-2B2), 3)
1.10 (28)
1.10 (28) 0.06 (1.5)
0.37 (9.5)
7/16-14UNC2), 3)
1.68 (43 -0.2)
DIA 1.500
1.71
(43.5)
2.44 (61.9)
2.44 (61.9)
Ports
Designation Port for Standard Size4) Maximum pres- State
sure [psi (bar)]4)
B Service line SAE J518 1 1/4 in 4000 (350) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.75 (19) deep
S Inlet SAE J518 2 1/2 in 145 (10) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.94 (24) deep
L Case drain fluid ISO 119266) 1 1/16-12UNF-2B; 0.63 (16) deep 30 (2) O5)
L1 Case drain fluid ISO 119266) 1 1/16-12UNF-2B; 0.63 (16) deep 30 (2) X5)
X Load-Sensing pressure ISO 11926 7/16-20 UNF-2A; 12 deep 4000 (350) O
X Control pressure DG-control DIN 3852 G 1/4 in; 12 deep 1800 (120) O
MB Measuring pressure in B DIN 38526) G 1/4 in; 12 deep 4000 (350) X
1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5
2) Thread according to ASME B1.1
3) For the maximum tightening torques the general information on page 40 must be observed.
4) Depending on the application, momentary pressure spikes can occur. Consider this when selecting measuring devices and
fittings.
5) Depending on the installation postion, L or L1 must be connected (see also page 38, 39).
6) The spot face can be deeper than as specified in the standard.
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 25/40
12.13 (308)
10.55 (268) 0.47 (12)
X
5.24 (133)
0.12 (3)
1.57 (40)
X
5.06 5.84
X (148.3)
(128.5)
Valve mounting for 5.22 Valve mounting for 6.49 (164.9)
counter clockwise (132.5) counter clockwise
rotation rotation
DRG ED7./ER7.
Pressure control, remotely operated Electro hydraulic pressure control
9.80 (249)
X
5.51 (140)
X
1.57 (40)
4.22 (107.2)
5.84
(148.4) 6.501) (165)
Valve mounting for
6.49 (164.9) counter clockwise
Valve mounting for
rotation
counter clockwise
rotation
DRF/DRS
Pressure and flow control
9.80 (249)
X
1.57 (40)
4.22 (107.2)
5.84
(148.4)
6.49 (164.9)
Valve mounting for
counter clockwise
rotation
1) ER7.: 7.87 in (200 mm) when using a sandwich plate pressure control.
26/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
DR – Pressure control
X
6.36 (161.6)
0.5
7.87 (200)
9(
15
2.79 (71)
4.09 (104)
)
5.9975
6.36 (161.6)
S
0.94 (24) L1 7.87 (200)
3.07 (78) 5.16 (131) 7.08 (179.8)
10.83 (275) 0.47 (12)
13.98 (355) 0.87 (22)
Valve mounting for
counter clockwise
rotation
1.26 (Ø32)
3.50 (88.9)
2.36 (Ø60)
2.63 (66.7)
S B
Drive shaft
S Splined shaft 1 3/4 in 13T K Parallel keyed shaft
8/16DP1) (SAE J744 - 44-4 (D)) (ISO 3019-1)
2.64 (67)
2.64 (67) 2.62 (66.5)
1/2-13UNC-2B2), 3)
1.26 (32)
1/2-13UNC2), 3)
0.06 (1.5)
1.941
1.7488
2.09
(53)
2.95 (75)
2.95 (75)
Ports
Designation Port for Standard Size4) Maximum pressure State
[psi (bar)]4)
B Service line SAE J518 1 1/4 in 4000 (350) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.75 (19) deep
S Inlet SAE J518 2 1/2 in 145 (10) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.94 (17) deep
L Case drain fluid DIN 38526) 1 1/16-12UN-2B; 0.59 (15) deep 30 (2) O5)
L1 Case drain fluid DIN 38526) 1 1/16-12UN-2B; 0.59 (15) deep 30 (2) X5)
X Load-Sensing pressure ISO 11926 7/16-20 UNF-2B; 0.47 (12) deep 4000 (350) O
X Control pressure DG-control DIN 3852 G 1/4 in ; 0.47 (12) deep 1800 (120) O
MB Measuring pressure in B DIN 38526) G 1/4; 0.47 (12) deep 4000 (350) X
1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5
2) Thread according to ASME B1.1
3) For the maximum tightening torques the general information on page 40 must be observed.
4) Depending on the application, momentary pressure spikes can occur. Consider this when selecting measuring devices and
fittings.
5) Depending on the installation postion, L or L1 must be connected (see also page 38, 39).
6) The spot face can be deeper than as specified in the standard.
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
28/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
DG LA.D.
Two point control, directly operated Pressure, flow and power control
1.57 (40)
5.49 (139.5)
6.43
6.02 (153)
X 6.22 (158)
(163.3)
7.08 (179.8)
Valve mounting for
counter clockwise Valve mounting for
rotation counter clockwise
rotation
DRG ED7./ER7.
Pressure control, remotely operated Electro hydraulic pressure control
10.19 (259)
X
(140)
X
X
1.57 (40)
max. 4.33 (110)
5.51
6.43 (163.3)
7.08 (179.8) 7.081) (180)
Valve mounting for Valve mounting for
counter clockwise counter clockwise
rotation rotation
DRF/DRS
Pressure and flow control
10.19 (259)
X
X
1.57 (40)
max. 4.33 (110)
6.43 (163.3)
7.08 (179.8)
Valve mounting for
counter clockwise
rotation
1) ER7.: 8.46 in (215 mm) when using a sandwich plate pressure control.
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 29/40
DR – Pressure control
0.81 (20.6)
57.
(Ø 152.4-0.063
5°
0.5
6.36 (161.6)
7.87 (200)
9
(15
2.80 (71)
4.09 (104)
)
6.0000
DIA 5.9975
DIA 1.26
2.63 (Ø32)
S
2.48 (Ø 63)
3.50 (88.9)
(66.7)
2.00 B
1.25 (31.8)
(50.8)
30/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Drive shaft
S Splined shaft 1 3/4 in 13T K Parallel keyed shaft
8/16DP1) (SAE J744 - 44-4 (D)) (ISO 3019-1)
2.64 (67)
2.64 (67) 2.62 (66.5)
1/2-13UNC-2B2), 3)
1.26 (32)
1/2-13UNC2), 3)
0.06 (1.5)
1.941
1.7488
2.09
(53)
2.95 (75)
2.95 (75)
Ports
Designation Port for Standard Size4) Maximum pres- State
sure [psi (bar)]4)
B Service line SAE J518 1 1/4 in 4000 (350) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.75 (19) deep
S Inlet SAE J518 2 1/2 in 145 (10) O
Connection threads ASME B1.1 1/2-13UNC-2B; 0.94 (17) deep
L Case drain fluid ISO 119266) 1 5/16-12UNF-2B; 0.59 (15) deep 30 (2) O5)
L1 Case drain fluid ISO 119266) 1 5/16-12UNF-2B; 0.59 (15) deep 30 (2) X5)
X Load-Sensing pressure ISO 11926 7/16-20 UNF-2B; 0.47 (12) deep 4000 (350) O
X Control pressure DG-control DIN 3852 G 1/4 in ; 0.47 (12) deep 1800 (120) O
MB Measuring pressure in B DIN 38526) G 1/4; 0.47 (12) deep 4000 (350) X
1) ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5
2) Thread according to ASME B1.1
3) For the maximum tightening torques the general information on page 40 must be observed.
4) Depending on the application, momentary pressure spikes can occur. Consider this when selecting measuring devices and
fittings.
5) Depending on the installation postion, L or L1 must be connected (see also page 38, 39).
6) The spot face can be deeper than as specified in the standard.
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 31/40
DG LA.D.
Two point control, directly operated Pressure, flow and power control
4.09 (140)
11.34 (288) 12.87 (327)
1.65 (42)
X
2.80 (71)
X
4.09 (104)
6.73 (171)
X 6.02 (153)
7.40 (188)
6.22 (158)
Valve mounting for
Valve mounting for counter clockwise
counter clockwise rotation
rotation
DRG ED7./ER7.
Pressure control, remotely operated Electro hydraulic pressure control
10.55 (268)
X MB
(140)
X
5.51
4.57 (116)
1.65 (42)
6.73 (171)
7.40 (188) 7.081) (180)
Valve mounting for Valve mounting for
counter clockwise counter clockwise
rotation rotation
DRF/DRS
Pressure and flow control
10.55 (268)
X MB
4.57 (116)
1.65 (42)
6.73 (171)
7.40 (188)
Valve mounting for
counter clockwise
rotation
1) ER7.: 8.46 in (215 mm) when using a sandwich plate pressure control.
32/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
+0.02 )
3.2508
DIA 3.2520
(Ø82.55 +0.05
6.
45°
A3
B
A2
(to mounting flange face) A1
6.
(Ø82.55 +0.05
A3
B A2
(to mounting flange face) A1
5.7
DIA 4.0019
NG45...71
100 14.17 1.81 0.67 M12 x 1.75;
4.0008
+0.02
Ø101.6 +0.05
DIA 4.0019
45°
(360) (45.9) (16.9) 0.71 (18) deep
140 14.84 1.81 0.67 M12 x 1.75;
(377) (45.9) (16.9) 0.71 (18) deep
A4
180 15.24 1.81 0.67 M12 x 1.75;
(387) (45.9) (16.9) 0.71 (18) deep
Thread of all sizes at U00 M12 x 1.75;
A3
B A2
0.87 (22) deep
(to mounting flange face) A1
DIA 5.002
5.001
DIA 5.002
5.001
5.001 (Ø127+0.02 )
140 14.84 2.44 0.80 M16 x 2;
+0.05
DIA5.002
(180) A4
0.35 (9)
0.59 (15)
A3
A2 NG100
(to mounting flange face) A1
M12x0.98 (25)
DIN 912-10.9 (4x) A3
B NG71 A2
(to mounting flange face) A1
(Ø152.4+0.05
DIA 6.002
6.001
M12x0.98 (25)
B DIN 912-10.9 A3
(4x) NG71 A2
(to mounting flange face) A1
1
m1 m2 m3 Tm = (m1 • l1 + m2 • l2 + m3 • l3) • [lb-ft (Nm)]
12 (102)
l1
l2
l3
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 37/40
(2)
(1)
Ø37
50
68.5
PE PE
A A
1 2 1 2
Electronic controls
Control Electronics funktion Electronics Further information
VT2000 1) analog RE 29 904
Electric pressure control Controlled power outlet VT 11029 1);
analog RE 29741
VT 11030 1)
1) only 24V nomilal voltage
38/40 Bosch Rexroth Corp. A10VSO Series 32 RA 92714-A/06.11
Installation notes
General Below-reservoir installation (standard)
The axial piston unit must be filled with hydraulic fluid and air Below-reservoir installation means the axial piston unit is ins-
bled during commissioning and operation. This must also be talled outside of the reservoir below the minimum fluid level.
observed following a longer standstill as the axial piston unit
empty via the hydraulic lines.
Especially with the installation position "drive shaft upwards" 1 2
or "drive shaft downward", attention must be paid to a comple-
te filling and air bleeding since there is a risk, for example, a min 200 mm a min 200 mm
of dry running. F F
ht min ht min
The case drain fluid in the case interior must be directed to the 200 mm SB
200 mm SB
h min h min
reservoir via the highest case drain port (L1, L2, L3).
100 mm 100 mm
For combinations of multiple units, make sure that the respec- L
tive case pressure in each unit is not exceeded. In the event of L L1
pressure differences at the drain ports of the units, the shared S
drain line must be changed so that the minimum permissible S
L1
case pressure of all connected units is not exceeded in any
situation. If this is not possible, separate drain lines must be
laid if necessary.
To achieve favorable noise values, decouple all connecting 3 4
lines using elastic elements and avoid above-reservoir installa-
tion.
a min 200 mm a min 200 mm
In all operating states, the suction line and case drain line F F
must flow into the reservoir below the minimum fluid level . ht min ht min
200 mm SB 200 mm SB
The permissible suction height hS is a result of the overall h min h min
pressure loss, but may not be greater than hS max = 800 mm. 100 mm 100 mm
The minimum suction pressure at port S must also not fall
L1 S S
below 12 psi (0.8 bar) absolute during operation.
Installation position
L
See the following examples 1 to 12. L1
L
Additional installation positions are available upon request.
Recommended installation positions: 1 and 3.
Installation position Air bleed Filling
1, 3 F S + L, L1 (F)
2, 4 F S + L, L1 (F)
Key, see page 39.
Conversation Table
mm in
100 = 3.94
200 = 7.87
RA 92714-A/06.11 A10VSO Series 32 Bosch Rexroth Corp. 39/40
Installation notes
Above-reservoir installation Inside-reservoir installation
Above-reservoir installation means the axial piston unit is Inside-reservoir installation means the pump is installed within
installed above the minimum fluid level of the reservoir. the minimum reservoir fluid level.
To prevent the axial piston unit from draining, a height diffe-
rence hES min of at least 25 mm is required in installation 9 10
position 6
Observe the maximum permissible suction height hS max = 800 mm. a min 200 mm a min 200 mm
A check valve in the case drain line is only permissible in indivi-
dual cases. Consult us for approval.
L
ht min
SB
ht min
5 6 SB
L1
S
L
F F L1
hES min 25 mm S
L
100 mm
100 mm
L
h min
h min
L1
S
S
L1
hs max hs max
800 mm 800 mm 11 12
ht min
ht min
S
7 8 L1
F
L L
F SB SB
S
100 mm
100 mm
L1 S
h min
h min
L
L1
L
hs max hs max
800 mm 800 mm Installation position Air bleed Filling
ht min 200 mm SB ht min 200 mm SB 9, 11 L, L1 L, L1
h min 100 mm h min 100 mm 10, 12 L, L1 S + L, L1
a min 200 mm a min 200 mm
General information
–– The A10VSO pump is designed to be used in open circuit.
–– Project planning, assembly and commissioning of the axial piston unit require the involvement of qualified personnel.
–– Before operating the axial piston unit, please read the appropriate operating instructions thoroughly and completely.
If necessary, request these from Bosch Rexroth.
–– During and shortly after operation, there is a risk of burns on the axial piston unit and especially on the solenoids.
Take appropriate safety measures (e.g. by wearing protective clothing).
–– Depending on the operating conditions of the axial piston unit (operating pressure, fluid temperature), the characteristics may
shift.
–– Service line ports:
-- The ports and fixing threads are designed for the specified maximum pressure. The machine or system manufacturer must
ensure that the connecting elements and lines correspond to the specified operating conditions (pressure, flow, hydraulic fluid,
temperature) with the necessary safety factors.
-- The service line ports and function ports are only designed to accommodate hydraulic lines.
-- Pressure cut-off and pressure control do not provide security against pressure overload. A separate pressure relief valve is to
be provided in the hydraulic system.
–– The data and notes contained herein must be adhered to.
–– The product is not approved as a component for the safety concept of a general machine according to DIN EN ISO 13849.
–– The following tightening torques apply:
-- Fittings:
Observe the manufacturer‘s instruction regarding the tightening torques of the used fittings.
-- Fixing screws:
For fixing screws with metric ISO thread according to DIN 13 or thread according to ASME B1.1, we recommend checking the
tightening torque individually according to VDI 2230.
-- Female threads in axial piston unit:
The maximum permissible tightening torques MG max are maximum values for the female threads and must not be exceeded.
For values, see the following table.
-- Threaded plugs:
For the metal threaded plugs supplied with the axial piston unit, the required tightening torques of the threaded plugs MV
apply. For values, see the following table.