Beruflich Dokumente
Kultur Dokumente
ELECTRICAL 2(TTA)
INSTRUCTIONS
1.NUMBER OF QUESTIONS 25
2.HAS A TIME LIMIT OF 15 MINUTES
3.HAS A PASS MARKS OF 30%
4.QUESTIONS PER PAGE 1
5.EACH QUESTIONS HAS 1 MARKS
6.NEGATIVE MARKING FOR EACH QUESTIONS 0.25
7.WILL ALLOW TO YOU GO BACK ,SKIP AND CHANGE YOUR ANSWERS
8.WILL ALLOW TO YOU PRINT OUT YOUR RESULT AND CERTIFICATE
9.WILL ALLOW TO YOU PRINT OUT YOURS RESPONSE SHEET WITH CORRECT ANSWER KEY AND EXPLANATION
10.WE WILL PROVIDE YOURS RESULT,CERTIFICATE AND YOUR RESPONSE SHEET TO YOURS EMAIL ID AT END OF ONLINE
TEST
.
.
.
Max Time Al lowed: 15 mi n
C. Any of these
B. weight of copper
C. all of these
Q.4) The capacitance of a small single phase motor will be of the order of
A. Micro or pico farads.
C. Farads
D. Kilo farads
B. 4%
C. 14%.
D. 1.4%
1 of 4 9/14/2016 11:47 AM
Printable Quiz: ELECTRICAL 2(TTA) http://www.proprofs.com/quiz-school/printquiz.php?title=electrical-2tt...
B. wrought iron
C. silicon steel
D. cast iron
Q.8) The motor used for driving the record player deck is
A. dc series motor
B. synchronous motor
C. hysteresis motor
D. dc shunt motor.
C. Copper loss
B. reluctance motors.
C. dc shunt motor
D. induction motor
D. Synchronous motor
Q.12) When V is the v oltage applied across the insulation, the dielectric loss for an insulating material
will be proportional to
A. V2
B. 1/ V
C. V
D. 1/ V2
B. all of these
C. reducing noise
Q.14) Which component of the no load current of the transformer is opposite in phase to the induced
emf ?
A. none of these
B. both of these
C. magnetizing component
Q.16) A wound rotor induction motor is preferred over squirrel cage induction motor when the major
consideration involv ed is
A. high starting torque
B. all of these
2 of 4 9/14/2016 11:47 AM
Printable Quiz: ELECTRICAL 2(TTA) http://www.proprofs.com/quiz-school/printquiz.php?title=electrical-2tt...
Q.17) For ceiling fans generally the single phase motor used is
A. split phase type
B. any of these
Q.19) In electrical machines the material preferred for pole shoes of electro-magnets is
A. Pure iron
B. Lead.
C. Aluminum
D. Copper
B. Belt drive
C. Fluid coupling.
D. Chain drive
Q.22) When smooth and precise speed control over a wide range is desired, the motor preferred is
A. squirrel cage induction motor
C. dc motor.
D. synchronous motor
Q.24) When commutation is obtained by increasing the current density at the leading edge and
decreasing the same at trailing edge, it is known as
A. straight commutation
B. over commutation
C. sinusoidal commutation.
D. under commutation
B. coil-sides
C. slots.
D. coils
3 of 4 9/14/2016 11:47 AM
Printable Quiz: ELECTRICAL 2(TTA) http://www.proprofs.com/quiz-school/printquiz.php?title=electrical-2tt...
Answer Key
Q.1) Ward Leonard controlled dc motors
Q.2) all of the above.
Q.3) all of these
Q.4) Micro or pico farads.
Q.5) 4%
Q.6) directly proportional to flux density
Q.7) silicon steel
Q.8) hysteresis motor
Q.9) Copper loss
Q.10) reluctance motors.
Q.11) AC slip ring motor
Q.12) V2
Q.13) suppressing undesirable harmonics
Q.14) core loss component
Q.15) brushes from carrying circulating currents
Q.16) all of these
Q.17) permanent capacitor type.
Q.18) interchanging the brush leads
Q.19) Pure iron
Q.20) increasing magnetic flux
Q.21) Gearing
Q.22) dc motor.
Q.23) approximately constant speed and load
Q.24) over commutation
Q.25) coils
4 of 4 9/14/2016 11:47 AM