Beruflich Dokumente
Kultur Dokumente
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
4-Port Antenna
Mechanical specifications
2)
Accessories (order separately if required)
3)
1)
Remarks Weight approx. Units per
Type No. Description
mm | inches kg | lb antenna
1917 | 75.5
1960 | 77.2
2000 | 78.7
2116 | 83.3
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Material: Reflector screen: Weather-proof aluminum.
Fiberglass housing: It covers totally the internal antenna components.
The special design reduces the sealing areas to a minimum and
guarantees the best weather protection. Fiberglass material guarantees
optimum performance with regards to stability, stiffness, UV resistance
and painting. The color of the radome is light grey.
All screws and nuts: Stainless steel.
Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.
Adjustment long neck
mechanism
with integrated
scale
4)
1) 9 | 0.4
2) 72 | 2.8
3) 64 | 2.5
4) 35 – 42 | 1.4 –1.7
Layout of interface:
960 RCU
0– 17
79 1
0–
U
RC
218
0
149 | 5.9 *
167 | 6.6 *
–45° +45°
790–960 790–960
106 | 4.2
88 | 3.5
Subject to alteration.
45 | 1.8
–45° +45°
1710–2180 1710–2180
50 | 2.0
936.4842/a
103 | 4.1
180 | 7.1
262 | 10.3 *
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Mounting Hardware
Clamp Included in the Scope of Supply
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.
1
2
2
➀ Adjustment wheel with twist-lock ➀ Thread for fixing the protective To set the downtilt angle exactly,
function. cap or the RCU (Remote Control you must look horizontally at the
➁ Downtilt spindle with integrated Unit). scale. The lower edge of the gear-
scale. ➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
max.° – 0°
Remove the protective cap. Set downtilt angle by rotating the Screw on the protective cap again.
adjustment wheel.
For a description of RCU installation please refer to the respective data sheet.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions for Feederline Installation
on XXPol Panels with four Connectors
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
Ventilation hole
Layout of interface:
– RF inputs / polarization
– Adjustment mechanism
– Frequency range
Protective cap covering
adjustment mechanism
Subject to alteration.
Start with the rearside located interfaces. After feederline installation the optional For a full description of RCU installation
remote control units (RCU) can be please refer to the respective data sheet.
Place the connector carefully and fix the
mounted.
nut using a torque-wrench (according to
936.4142