Beruflich Dokumente
Kultur Dokumente
1. the voltage output of the rotary inverter in an high-output brushless AC generator can be altered by
A. changing the field current in the motor circuit
B. changing the armature current in the motor circuit
C. changing the field current in the generator circuit
13. why does generator have to be in the same phase and frequency before parallel
A. because of the current in TRU of (secondary winding)
B. because of the current flowing back in to the generator
C. ?
21. the bulb of halogen lamp that used on the exterior of the aircraft
A. has an tungsten filament and filled with insert gas
B. fill with halogen gas and has no filament
C. has an tungsten filament and filled with iodle vapour
22.2 when battery removal from aircraft, which lead should remove first
A. the lead going to ground
B. the lead going to solenoid (hot lead)
C. no difference provided power off
23. Bonding of A/C determine by
A. Resistance
B. Current
C. voltage
28. DC output usually measure at overvoltage sensing Field flashing carried at: (when offline)
A. Generator output voltage adjustment: (off load)
B. Field current test load sharing: (all gen on load )
C. Field voltage
32. Generator voltage depend on 3 factors ( the strength of the magnet, the number of turns
A. current, magnetic field, rotor speed in the wire coil, and the speed at which the magnet
B. current, M field, conductor in series in armature or coil rotates.)
C. current, M field, conductor in parallel in armature
33. Frequency of generator depend on (the ac frequency depends only on the speed of rotation)
A. number of pair of pole, M field
B. number of pair of conductor, M field
C. number of pair of pole, rotor speed
38. In No-break power transfer, when the ground power is on, start all generator
A. trip the ground power before start generator (john)
B. parallel supply…
C. start AC generator is not allowed
56. Specific gravity of Ni-Cd battery was measured 1.220@100F, what is the ture
A. 1.112
B. 1.220
C. 1.228
56.2 how much leakage current between cell and the case is considered excessive for Ni-Cd battery
A. > 10ma
B. > 50ma
C. > 100ma
60. Power is not supply to the Emergency power pack for 6 days, to test the system validity, apply power must
A. wait at least 20 hours
B. max turn on time refer to MM
C. to perform the test
64. During installation of carbon pile regulator, magnetic core screw can
A. adjust to regulate the current
B. adjust to regulate the voltage
C. cannot be adjusted
68. DC motor no voltage output during normal operation or rpm, most likely fault
A. failed brushes
B. ?
C. ?
73. Open circuit voltage coil in carbon pile voltage regulator in 28V DC generator, the output voltage
A. maintain a constant 28V
B. decreased to 2V
C. increase into overvoltage condition
74. To ensure vital service like fire extinguisher the squib circuit is powered in real emergency
A. connects squib circuit to essential bus (john)
B. squib circuit connects to battery line
C. squib circuit connects to hot battery bus
74.1 which following operation must rely on battery power
A. power on battery bus
B. APU electrical starting
C. firing on fire extinguisher bottle
76. Aircraft electrical system is protected against short-circuit feeder line of generator bus bar
A. by…. Frequency protection
B. by differential current protection
C, by…. Over volt protection
80. In what conditions needed to adjust the electrolyte temp level for lead acid cell?
A. For new electrolyte
B. When charge the battery from a nearly flat state
C. Adjust electrolyte level at full charged state only
87. In parallel electrical system, a load bus on the left system short to the ground, the appropriate action would
A. isolate it from generator by tripping respective GCR
B. isolate it from tie bus by tripping BTB (john)
C. isolate it from right system by tripping SSB
88. the purpose of the capacitor installed between the voltage regulator battery
A. As AC filter to the alternator output
B. prevent the operation of the overvoltage protection circuit due to voltage spike
C. protect the voltage regulator from any long term overvoltage condition
93.1 DC generator system the over volt condition is sensed by monitoring the voltage
A. of the field
B. of the generator output
C. difference between the generator and the main bus bar
106.1 In No break power transfer (NBPT), when the ground power is on, start all generator
A. trip the ground power before start generator
B. parallel supply ……. For a while
C. start AC generator is not allowed
106.2 In NBPT, the external power is currently line on while starting the generation, what will be
A. kick of the external power
B. both power can supple split together of a while but no current affect any
C. cut off the generation power
112. Brushless aircraft gen, why does it not need flashing field
A. rectifying circuit
B. residual magnetism
C. PMG at main poles
113. In high output voltage generator, inter-poles and compensating winding gives
A. increase voltage output
B. reduce arcing
C. ?
121. Ni-Cd battery, separator of ….? And cellophane, what is cellophane for?
A. strengthen the separator
B. prevent oxygen leak from negative plate to positive plate
C. prevent thermal runway
125. During no break power transfer, an external power is currently online and main generator brought in, it follow than
A. The external power is tripped, when the main generator kicks in (john)
B. both power will be parallelized for a split second, and they will not be interrupted
C. The requested power will not be rejected
126. NiCd potassium ratio is
A. 30%
B. 40%
C. 50%
133.1 in generator reverse current protection system has differential relay and pilot relay, when voltage increase
A. differential relay operate after pilot relay
B. pilot relay operate after differential relay
C. both relay operate
134. External supply with 2 shorter pins shorted
A. cannot power aircraft
B. cannot disconnect from aircraft
C. extreme spark may occur
140. Vital bus Vital bus --- first is supplied by GEN bus,
A. power from battery and gen bus then supplied by BATTERY
B. directly from battery bus
C. ?
143.1 In normal operation, split bus electrical system with each generator supplying its own generator bus
A. the BTB would be closed only if APU running
B. the transfer relay would be closed
C. the BTB would be open
144. Frequency 1000 with a period is 2 micro-second, The peak power is 1000 watt, what is the average power?
A. 2 watt
B. 40 watt
C. 500 watt
154. Difference of voltage of 2 generators in parallel. What is used to adjust the voltage to be the same at the each of the
O/P of generator automatically?
A. current coil
B. equalizing circuit
C. voltage coil
156. Real load sharing, make sure the AC generators are in parallel operation, on each generator
A. adjust the rotational speed of individual generator
B. increase or decrease the individual load
C. adjust phase angle of individual generator
156.1 The real load sharing loop between 2 generators is only active when both
A. ?
B. GCB and BTB are closed
C. ?
160. Loss of the load controller signal to an IDG speed governor trim head would
A. cause the IDG to overspeed at once
B. shut down the IDB automatically
C. cause the IDG to the basic governor setting
161. The NO SMOKING sign can automatically comes on when
A. flight phase
B. altitude of aircraft
C. flap position
165. Flashing the field of a DC generator is only carried out with the generator
A. online
B. offline
C. trip ( under overhaul)
170. How to carry out the frequency adjustment in the rotary inverter
A. field current in the motor circuit
B. field current in the generator circuit
C. field voltage in the motor circuit
175. When taking the s.g of battery acid, take into account:
A. temp of the acid
B. temp of the ambient air
C.
189. what should be done to a transformer secondary connections which are open circuit?
A. short the terminals together
B. put a set resistance across the terminals
C. leave the terminals open circuit
191. loss of an electrolyte in a battery is due to (low electrolyte in a nicad battery is caused by)
A. excessive charging current (A. excessive electrical loading)
B. insufficient charging current (B. high charge current)
C. excessive charging voltage (C. low charge current)
196. What should be taken into account when measuring the SG of a battery
A. the outside temperature
B. electrolyte temperature
C. charge stage of the battery
206. when terminating an aluminium cable, what preparations would be carried out before crimping?
A. just terminate
B. apply a mixture of 50% petroleum jelly and zinc oxide
C. degrease spripped cable
209. What is the purpose of the current transformer on a neutral phase of an AC penerator
A. Negative phase sequencing
B. open phase
C. differential protection