Beruflich Dokumente
Kultur Dokumente
chassis PL13.9
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
131218
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
1-1 PL13.9SP
[TYPE B, E, F]
< TUNER / NTSC >
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
TV.ch.4 dBμ 18 20
2. Synchronizing Sens. CA.ch.31 dBμ 18 20
CA.ch.87 dBμ 18 23
1-2 PL13.9SP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
Circuit AC line cord directly into a 120 V AC outlet. (Do
1. Before returning an instrument to the not use an isolation transformer during this
customer, always make a safety check of the test.) Use a leakage current tester or a
entire instrument, including, but not limited to, the metering system that complies with American
following items: National Standards Institute (ANSI) C101.1
a. Be sure that no built-in protective devices are Leakage Current for Appliances and
defective and have been defeated during Underwriters Laboratories (UL) 1410, (50.7).
servicing. (1) Protective shields are provided With the instrument AC switch first in the on
on this chassis to protect both the technician position and then in the off position, measure
and the customer. Correctly replace all missing from a known earth ground (metal water pipe,
protective shields, including any removed for conduit, etc.) to all exposed metal parts of the
servicing convenience. (2) When reinstalling instrument (antennas, handle brackets, metal
the chassis and/or other assembly in the cabinet, screw heads, metallic overlays, control
cabinet, be sure to put back in place all shafts, etc.), especially any exposed metal
protective devices, including but not limited to, parts that offer an electrical return path to the
nonmetallic control knobs, insulating chassis. Any current measured must not
fishpapers, adjustment and compartment exceed 0.5 milli-ampere. Reverse the
covers/shields, and isolation resistor/capacitor instrument power cord plug in the outlet and
networks. Do not operate this instrument or repeat the test.
permit it to be operated without all
protective devices correctly installed and READING SHOULD
functioning. Servicers who defeat safety NOT BE ABOVE 0.5 mA
features or fail to perform safety checks
may be liable for any resulting damage. LEAKAGE
DEVICE CURRENT
b. Be sure that there are no cabinet openings BEING TESTER
through which an adult or child might be able to TESTED + _
insert their fingers and contact a hazardous
voltage. Such openings include, but are not TEST ALL EXPOSED
limited to, (1) spacing between the Liquid METAL SURFACES
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly ALSO TEST WITH
secured cabinet back cover. PLUG REVERSED
c. Antenna Cold Check - With the instrument AC USING AC
plug removed from any AC source, connect an ADAPTER PLUG EARTH
electrical jumper across the two AC plug AS REQUIRED GROUND
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter ANY MEASUREMENTS NOT WITHIN THE
to the AC plug prongs tied together and touch LIMITS SPECIFIED HEREIN INDICATE A
the other ohmmeter lead in turn to each tuner POTENTIAL SHOCK HAZARD THAT MUST
antenna input exposed terminal screw and, if BE ELIMINATED BEFORE RETURNING THE
applicable, to the coaxial connector. If the INSTRUMENT TO THE CUSTOMER OR
measured resistance is less than 1.0 megohm BEFORE CONNECTING THE ANTENNA OR
or greater than 5.2 megohm, an abnormality ACCESSORIES.
exists that must be corrected before the
2. Read and comply with all caution and safety-
instrument is returned to the customer. Repeat
related notes on or inside the receiver cabinet, on
this test with the instrument AC switch in the off
the receiver chassis, or on the Liquid Crystal
position.
Panel.
2-1 LTVN_ISP
3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and
to the mechanical or electrical design of this TV mechanical parts have special safety-related
receiver. Design alterations and additions, characteristics which are often not evident from
including, but not limited to circuit modifications visual inspection, nor can the protection they give
and the addition of items such as auxiliary audio necessarily be obtained by replacing them with
and/or video output connections, might alter the components rated for higher voltage, wattage, etc.
safety characteristics of this receiver and create a Parts that have special safety characteristics are
hazard to the user. Any design alterations or identified by a # on schematics and in parts lists.
additions will void the manufacturer's warranty and Use of a substitute replacement that does not
may make you, the servicer, responsible for have the same safety characteristics as the
personal injury or property damage resulting recommended replacement part might create
therefrom. shock, fire, and/or other hazards. The product's
4. Hot Chassis Warning - safety is under review continuously and new
instructions are issued whenever appropriate.
a. Some TV receiver chassis are electrically
Prior to shipment from the factory, our products
connected directly to one conductor of the AC
are strictly inspected to confirm they comply with
power cord and maybe safety-serviced without
the recognized product safety and electrical codes
an isolation transformer only if the AC power
of the countries in which they are to be sold.
plug is inserted so that the chassis is
However, in order to maintain such compliance, it
connected to the ground side of the AC power
is equally important to implement the following
source. To confirm that the AC power plug is
precautions when a set is being serviced.
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2 LTVN_ISP
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
11~13 lb (5~6 kg) of force in any direction will not
loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3 LTVN_ISP
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and Chassis or Secondary Conductor
surrounding metallic parts. (See Fig. 1)
Primary Circuit
Table 1: Ratings for selected area
Clearance d' d
AC Line Voltage Region
Distance (d), (d’)
U.S.A. or ≥ 3.2 mm
110 to 130 V
Canada (0.126 inches)
Fig. 1
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
U.S.A. or 0.15 μF CAP. & 1.5 kΩ RES. Exposed accessible
110 to 130 V i ≤ 0.5 mA rms
Canada Connected in parallel parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4 LTVN_ISP
STANDARD NOTES FOR SERVICING
Circuit Board Indications How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is
1. Removal
indicated as shown.
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View Bottom View 1. Prepare the hot-air flat pack-IC desoldering
Input machine, then apply hot air to the Flat Pack-IC
Out In (about 5 to 6 seconds). (Fig. S-1-1)
Pin 1
10
3-1 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron:
be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from
pin or the solder lands under the IC when all pins of the flat pack-IC. When you use solder
removing it. flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC Flat Pack-IC Desoldering Braid
Desoldering
Machine
CBA
Soldering Iron
Masking Flat Pack-IC Fig. S-1-3
Tape
Tweezers 2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
Fig. S-1-2
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4
3-2 TVN_SN
With Iron Wire: 2. Installation
1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA
flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more
you can remove it easily. (Fig. S-1-3) easily.
2. Affix the wire to a workbench or solid mounting 2. The “ I ” mark on the flat pack-IC indicates pin 1.
point, as shown in Fig. S-1-5. (See Fig. S-1-7.) Be sure this mark matches the
3. While heating the pins using a fine tip soldering pin 1 on the PCB when positioning for installation.
iron or hot air blower, pull up the wire as the solder Then presolder the four corners of the flat pack-IC.
melts so as to lift the IC leads from the CBA (See Fig. S-1-8.)
contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that
4. Bottom of the flat pack-IC is fixed with glue to the none of the pins have solder bridges.
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6) Example :
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Hot Air Blower Fig. S-1-7
or
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3 TVN_SN
Instructions for Handling Semi-
conductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
<Incorrect>
CBA
1MΩ
CBA
1MΩ
Conductive Sheet or
Copper Plate
3-4 TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS
[TYPE A, B] Step/
Fig.
Loc. Part Removal Note
No.
Screw Torque Specification No.
Step/
Fig.
Loc. Part
No.
Removal Note Precautions concerning the LCD Panel
No. Assembly:
Stand Base 1. When you disassemble/re-assemble the Front
[1] D1 3(S-1), Stand Neck ---
Assembly Cabinet or Function CBA Unit
[2] Rear Cover D1 8(S-2), 2(S-3), (S-4) --- • Be careful not to break the hooks. If you pull with too
much force, the hooks may be damaged.
4-1 PL13.9_DC
• When disassembling, first detach the hooks on each 2. When you disassemble/re-assemble the X-PCB
end on the bottom side, then detach the remaining Cover
hooks. • Be careful not to break the hooks. If you pull with too
• Make sure the hooks are securely in place when much force, the hooks may be damaged.
assembling. • When disassembling, first hold the top and bottom of
• Be careful not to scratch the display panel when the X-PCB Cover on both ends and then moving
assembling. toward the center, lift up the top side to detach the
hooks.
• Make sure the Function CBA Unit and Shield Plate
• When assembling be careful not to damage the
are securely in place when re-assembling.
X-PCB Board or the COF(Chip On Film).
• The screw tightening torque must be 5.2lb·in • Make sure the hooks are securely in place when
(6kgf·cm). re-assembling.
• After reassembling the Front Cabinet or Function • The screw tightening torque must be 5.2lb·in
CBA Unit, check the operational sensitivity of the (6kgf·cm).
touch sensor to make sure it functions normally.
• Make sure to replace the Decoration Plate to a new
one when replacing the Front Cabinet.
(S-3)
(S-2)
(S-4)
(S-2)
Stand Neck
(S-1)
[1] Stand Base
Assembly
Fig. D1
4-2 PL13.9_DC
Type A
[4] Digital Main CBA Unit
(S-6)
Jack Holder
Type B
(S-5)
(S-6)
Jack Holder
[3] Power Supply CBA
Fig. D2
[5] Speaker
1
Shield Plate*
4-3 PL13.9_DC
1
[9] Front Cabinet*1 [8] X-PCB Cover*2
Decoration Plate*
1
Hook* 2
Hook*
(S-8)
1
Hook*
1
Hook*
(S-9)
Fig. D4
*1: Make sure to read all the precautions on pages 4-1 and 4-2 when you disassemble/re-assemble
the Front Cabinet.
*2: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the
X-PCB Cover.
4-4 PL13.9_DC
TV Cable Wiring Diagram
Digital Main
Power Supply CBA CBA Unit
CN1001
*1 CN3013
*2 CN3905
*1 CN3701
CN501
*2 CN3601
CN601
*1 CN3101 CN3801
*2 CN3105
To AC Cord
CN4001
*1: TYPE A
*2: TYPE B
Fig. D5
4-5 PL13.9_DC
[TYPE C, D, E, F] 4. Disassembly Method
Screw Torque Specification Step/
Fig.
Loc. Part Removal Note
No.
Ref. Part Tightening No.
Part Name
No. Number Torque
Stand
SCREW BIND [1] D1 3(S-1) ---
L7 GBHP3100 BLACK_NI +P-TITE Assembly
M3X10.0
[2] Rear Cover D1 8(S-2), 2(S-3), (S-4) ---
SCREW BIND
L23 GBJS3060 3CHROM +S-TITE Power
M3X6.0 5.2±0.9lb·in
D2 4(S-5), CN601,
[3] Supply ---
D5 CN501, CN1001
SCREW BIND CBA
L27 GBHS3080 BLACK_NI +S-TITE
M3X8.0 4(S-6),CN3013*1,
SEMS-SW PAN CN3006*2, CN3904*3,
L45 FPH34100 BLACK_NI + M4X10.0 Digital Main D2 CN3905*4,
[4] ---
STAND SCREW KIT CBA Unit D5 CN3101*1, *2,
SSK1*1 1ESA34004 (SCREW BIND CN3105*3, *4, CN3801,
BLACK_NI +P-TITE Jack Holder
M4X14.0) (approx.
STAND SCREW KIT 8.7±0.9lb·in)* [5] Speaker D3 --------------- ---
(SCREW BIND
SSK1*2 1ESA35205 LCD Panel
BLACK_NI +P-TITE [6] D3 --------------- ---
M4X14.0) Assembly
* For reference X-PCB
[7] D4 2(S-7) 1
Cover
*1: TYPE C, F
Front
*2: TYPE D, E [8] D4 4(S-8) 2
Cabinet
Function Sensor Lens, Shield
[9] D4 2
CBA Unit Plate, Control Plate
3. Disassembly Flowchart ↓ ↓ ↓ ↓ ↓
This flowchart indicates the disassembly steps for the (1) (2) (3) (4) (5)
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the *1: TYPE C
steps in reverse order. Bend, route and dress the *2: TYPE D
cables as they were.
*3: TYPE E
[1] Stand
Assembly *4: TYPE F
4-6 PL13.9_DC
Precautions concerning the LCD Panel 2. When you disassemble/re-assemble the Front
Assembly: Cabinet or Function CBA Unit
1. When you disassemble/re-assemble the X-PCB • Be careful not to break the hooks. If you pull with too
Cover much force, the hooks may be damaged.
• Be careful not to break the hooks. If you pull with too • When disassembling, first detach the hooks on each
much force, the hooks may be damaged. end on the bottom side, then detach the remaining
• When disassembling, first hold the top and bottom of hooks moving toward the center.
the X-PCB Cover on both ends and then moving • Make sure the hooks are securely in place when
toward the center, lift up the top side to detach the assembling.
hooks. • Be careful not to scratch the display panel when
• When assembling, be careful not to damage the assembling.
X-PCB Board or the COF(Chip On Film).
• The Function CBA Unit and Sensor Lens are fixed in
• Make sure the hooks are securely in place when place by the hooks. Make sure these hooks are not
re-assembling. damaged. Make sure the Function CBA Unit and
• The screw tightening torque must be 5.2lb·in Sensor Lens are securely in place when
(6kgf·cm). re-assembling.
• The screw tightening torque must be 5.2lb·in
(6kgf·cm).
• After replacing the Front Cabinet or Function CBA
Unit, make sure the tact switches operate normally.
• Make sure to replace the Control Plate to a new one
when replacing the Front Cabinet.
(S-3)
(S-2)
(S-4)
(S-2)
(S-1)
Fig. D1
4-7 PL13.9_DC
Type C, D
[4] Digital Main CBA Unit
(S-6)
Jack Holder
Type E, F
(S-5) (S-6)
Jack Holder
Fig. D2
[5] Speaker
Fig. D3
4-8 PL13.9_DC
[7] X-PCB Cover*1
[8] Front Cabinet*2
Hook*2
Hook*1
(S-7)
Hook*2
Hook*2
Shield Plate
Sensor Lens*2
Hook*2
Control Plate*2
*1: Make sure to read all the precautions on pages 4-6 and 4-7 when you disassemble/re-assemble
the X-PCB Cover.
*2: Make sure to read all the precautions on page 4-7 when you disassemble/re-assemble the Front
Cabinet or Function CBA Unit.
4-9 PL13.9_DC
TV Cable Wiring Diagram
Digital Main
Power Supply CBA CBA Unit
CN1001 *1 CN3013
*2 CN3006
*3 CN3904
*4 CN3905
*1,*2 CN3701
CN501
*3,*4 CN3601
CN601
To AC Cord
Fig. D5
4-10 PL13.9_DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[TYPE A, C, D] How to set up the service mode:
General Note: “CBA” is abbreviation for Service mode:
“Circuit Board Assembly.” 1. Turn the power on.
Note: Electrical adjustments are required after 2. Press [MENU] button to display Setup menu.
replacing circuit components and certain
3. Select “Features”.
mechanical parts. It is important to perform
these adjustments only after all repairs and 4. Select “Software Upgrade”.
replacements have been completed. 5. Select “Current Software Info”.
Also, do not attempt these adjustments unless 6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on
the proper equipment is available. the remote control unit in this order. The following
screen appears.
Test Equipment Required
1. Remote control unit "*" differs depending on the models.
Safety: Safety_Non
HDMI EDID: **
HDMI UART: OFF Total Watch Time: *****
Touch Sensor Ver: -.-- / --- Lightsensor: **
5-1 PL13.9EA
1. Purity Check Mode The VCOM Adjustment should be
performed when replacing the
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
Digital Main CBA for 32PFL2508/F8(Serial
No.: VM3).
1. Enter the service mode.
2. Each time the [7] button on the remote control unit 2. VCOM Adjustment
is pressed, the display changes as follows.
Test Point Adj. Point
Purity Check Mode [CHANNEL UP/DOWN]
Screen
White mode
buttons
M. EQ. Spec.
[7] button
Color analyzer See below
Figure
Perpendicularity
[7] button
White 50% mode
Color Analyzer
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-2 PL13.9EA
The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal
performed when replacing the LCD Panel appears in the screen. (“Internal (Single)” appears
in the upper right of the screen as shown below.)
or Digital Main CBA.
3. White Balance Adjustment
Internal (Single)
Purpose: To mix red and blue beams correctly for
pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
x= 0.272 ± 0.003
Color temperature
y= 0.278 ± 0.003
7. Press [CHANNEL UP/DOWN] buttons to adjust
Internal pattern
Input Signal the color temperature becomes 12000°K
(40/80% raster)
(x= 0.272 / y= 0.278 ± 0.003).
Measurement point Screen center
8. Press [1] button to select the “HDR” for High Drive
CA-310 (KONICA MINOLTA Red adjustment (“HDR” appears in the screen.)
Luminance meter) or and press [CHANNEL UP/DOWN] buttons to
M. EQ.
measuring instrument as adjust the color temperature.
good as CA-310.
9. If necessary, adjust the “HDB” or “HDR” again.
60min.
10. Press [6] button to select the “LDB” for Low Drive
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
Shipment setting/ adjust the color temperature.
MODE setting of TV
Retail MODE
Ambient
25°C ± 5°C
temperature Internal (Single)
5-3 PL13.9EA
[TYPE B, E, F]
General Note: “CBA” is abbreviation for How to set up the service mode:
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
Service mode:
replacing circuit components and certain 1. Turn the power on.
mechanical parts. It is important to perform 2. Press [0], [6], [2], [5], [9], [6], and [INFO] buttons
these adjustments only after all repairs and on the remote control unit in this order. The
replacements have been completed. following screen appears.
Also, do not attempt these adjustments unless
"*" differs depending on the models.
the proper equipment is available.
[current]
Test Equipment Required File code:
Total checksum:
***-****_***_*
Push "0" key
1. Remote control unit Panel-Option code: **-***-***-***-***-***
***-***-***-***-***
2. Color Analyzer,
Press "POWER" key to exit.
CA-310 (KONICA MINOLTA Luminance meter) or
measuring instrument as good as CA-310. MAC address: **:**:**:**:**:**
ESN: *****************************
Flicker: *****
Tuner: ****
HDMI UART: OFF TotalWatchTime: *****
Touch Sensor Ver: ------ / -.--.-- SystemTime: **:**
EDID: Push "0" key Lightsensor: **
Perpendicularity
[7] button
White 50% mode
Color Analyzer
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
x= 0.272 ± 0.003
Color temperature
y= 0.278 ± 0.003
7. Press [CHANNEL UP/DOWN] buttons to adjust
Internal pattern
Input Signal the color temperature becomes 12000°K
(30/80% raster)
(x= 0.272 / y= 0.278 ± 0.003).
Measurement point Screen center
8. Press [1] button to select the “HDR” for High Drive
CA-310 (KONICA MINOLTA Red adjustment (“HDR” appears in the screen.)
Luminance meter) or and press [CHANNEL UP/DOWN] buttons to
M. EQ.
measuring instrument as adjust the color temperature.
good as CA-310.
9. If necessary, adjust the “HDB” or “HDR” again.
60min.
10. Press [9] button to select the “LDB” for Low Drive
Aging time (Retail MODE/100IRE Raster
HDMI 1080i@60) Blue adjustment (“LDB” appears in the screen.)
and press [CHANNEL UP/DOWN] buttons to
Shipment setting/ adjust the color temperature.
MODE setting of TV
Retail MODE
Ambient
25°C ± 5°C
temperature Internal (Single)
[TYPE A, C, D]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Panel Key
Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED FINISH”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
[TYPE B, E, F]
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on
the remote control unit.
3. Press [BACK] button to enter the Control Panel
Key Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check
mode.
6. Make sure to confirm the “INITIALIZED : OK”
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
6-1 PL13.9_INT
FIRMWARE RENEWAL MODE
[TYPE A, C, D]
Equipment Required
a. USB storage device
b. Remote Control Unit
Firmware Update Procedure
User Upgrade (Filename example: TVNB012_00_PF_XX91_AC.ecc)
Upgrade the firmware only. The setting values will not be initialized.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Update procedure
1. Turn the power on. 11. The update will start and the following will appear
2. Press [MENU] button to display Menu. in the screen.
3. Select “Features”. "*" differs depending on the models.
5. Select “Upgrade” to display Upgrade screen. Software upgrade in progress. Please wait.
6. Press [OK] button to display Software Upgrade Do not remove the USB storage device or
screen. turn the TV off while upgrade is in progress.
7. Select “USB” and press [OK] button. Current Version: *******-***-*-***-****
8. Insert the USB storage device to the USB port as New Version: *******-***-*-***-****
shown below. *1 Downloading...
0%
Rear Cabinet
(example)
Note: If the above screen isn’t displayed, repeat from
step 1.
USB port The appearance shown in *1 is described as follows.
Appearance State
Downloading the firmware from
Downloading...
USB storage the USB storage device.
device
Writing the downloaded firmware
Writing...
in flash memory.
Checking... Checking the new firmware.
Software Upgrade
9. Select “Check” and press [OK] button.
10. Select “Upgrade” and press [OK] button to start
software upgrade.
7-1 PL13.9FW
Factory Upgrade (Firmware Upgrade/Flash Upgrade)
Firmware Upgrade (Filename example: FACT_TVNB012_00_PF_XX91_AC.ecc)
Upgrade the firmware and initialize the setting values.
The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to
upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename.
If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the
filename.
Flash Upgrade (Filename example: ALL_TVNB012_00_PF_XX91_AC.ecc)
Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc.
Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the
TV after the initialization.
The Flash Upgrade will be done by it's unique file.
The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.
Update procedure
1. Turn the power off. The appearance shown in *1 is described as follows.
2. Insert the USB storage device to the USB port as Appearance State
shown below.
Downloading the firmware from
Downloading...
Rear Cabinet the USB storage device.
(example) Writing the downloaded firmware
Writing...
in flash memory.
Checking... Checking the new firmware.
USB port
7-2 PL13.9FW
[TYPE B, E, F] Update file selection screen appears as follows.
(Files included in the USB storage device are
displayed.
Equipment Required "*" differs depending on the models.
1. USB storage device
Select an upgrade file *****_******.upg
2. Remote Control Unit
*****_******.upg
Firmware Update Procedure *****_******.upg
1. Turn the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port as
shown below.
7-3 PL13.9(A3RF0UH)_FW
TROUBLESHOOTING
Note: This Troubleshooting section covers the entire PL13.9 chassis models. Thus some Reference number of
parts shown below may not be used depending on the model. Please refer to the parts list for each model.
No
Is the fuse (F602) normal? See FLOW CHART No.2 <The fuse blows out.>
Yes
Is normal state restored when once unplugged No Check if there is any leak or short-circuit on the
power cord is plugged again after several seconds? primary circuit component and repair it if defective.
Yes (C607, D601, D602, D603, D604, D605, D607A,
No D608, D609A, D621, D623, Q601, Q602, Q621,
Is the P-ON+21V line voltage normal? R602, R611, T601)
Yes
Check if there is any leak or short-circuit on the Check if there is any leak or short-circuit on the
primary circuit component and repair it if defective. each rectifying circuit component of secondary side
and repair it if defective.
Make sure to repair the primary circuit component before replacing the fuse (F602).
Does the photocoupler circuit on the secondary side No Check IC602, D660, D661, Q653 and their periphery
operate normally? circuit. Repair it if defective.
Yes
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side.
Repair it if defective. (D650, D651, D653, D655, Q656, Q658)
8-1 PL13.9ATR
FLOW CHART NO.5
P-ON+21V is not output.
Is approximately +20V voltage supplied to the cathode No Check D650, D651, C651, C652, C653 and their
of D650(D651)? periphery circuit. Repair it if defective.
Yes
Check if there is any leak or short-circuit on the load
circuit. Repair it if defective.
No
Is approximately +14V voltage supplied to the cathode Check D653, D654, D655, C654, C655 and their
of D653(D655)? periphery circuit. Repair it if defective.
Yes
No
Is approximately +14V voltage supplied to the Is approximately +14V voltage supplied to the
collector of Q656? emitter of Q658?
Yes Yes No
Replace Q656.
8-2 PL13.9ATR
[Video Signal Section]
FLOW CHART NO.1
[TYPE A, TYPE B]
The key operation is not functioning.
No
When touching each buttons, does the Pin(6) voltage Replace the Function CBA Unit.
of CN4001 decrease?
Yes
No
When pressing each buttons, does the Pin(6) voltage Replace the Function CBA Unit.
of CN4052 decrease?
Yes
No
Is approximately +3.3V voltage supplied to Pin(1) of Check AL+3.3V line and repair it if defective.
CN4001?
Yes
No
Is the "L" pulse supplied to Pin(5) of CN4001? Replace the Function CBA Unit.
Yes
Replace the Digital Main CBA Unit.
[TYPE C, TYPE D, TYPE E, TYPE F]
No operation is possible from the remote control unit. (Operation is possible from the unit.)
No
Is approximately +3.3V voltage supplied to Pin(1) of Check AL+3.3V line and repair it if defective.
CN4052?
Yes
No
Is the "L" pulse supplied to Pin(5) of CN4052? Replace the Function CBA Unit.
Yes
Replace the Digital Main CBA Unit.
No
Is approximately +20V voltage supplied to See FLOW CHART NO.5 <P-ON+21V is not output.
Pin(1, 2, 3, 4) of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(16) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
Digital Main CBA Unit or LCD Panel Assembly may
be defective. Check and replace these parts.
8-3 PL13.9ATR
[Audio Signal Section]
FLOW CHART NO.1
Audio is not output normally.
No
Is approximately +14V voltage supplied to Pin(6, 7, 8, 9) See FLOW CHART NO.6 <AMP+13V is not output.
of CN501? [Power Supply Section]>
Yes
No
Is approximately +3.3V voltage supplied to Pin(16) of See FLOW CHART NO.7 <AL+3.3V is not output.
CN501? [Power Supply Section]>
Yes
No
Are the audio signals output to Pin(1, 2, 3, 4) of CN3801? Replace the Digital Main CBA Unit.
Yes
8-4 PL13.9ATR
IC3005
(MAIN MICRO CONTROLLER)
AL+3.3V
RS4051
REMOTE
CN3009 SENSOR
D4051
USBDP
R10 USBDP POWER
USB JACK USBDN
T10 USBDN CN3101 CN4001
IC4001
REMOTE C14 5 REMOTE 5 (TOUCH SENSOR)
LED1 D14 LED DRIVE 6 LED1 4
Q3501, Q3502 2 SCL 8 4 SCL POWER 16 POWER
1 SDA 9 5 SDA SOURCE 17 SOURCE
KEY-IN1 A15 4 KEY-IN1 6 1 POWER
MENU 18 MENU
2 SOURCE CH UP 19 CH UP
CH DOWN 21 CH DOWN
3 MENU
[TYPE A, TYPE C, TYPE D]
VOL UP 22 VOL UP
6 CH UP VOL DOWN 23 VOL DOWN
11 CH DOWN
AUDIO-MUTE
C1 AUDIO-MUTE 12 VOL UP
COMP-DET
TO VIDEO/AUDIO N12 COMP-DET
HP-MUTE
BLOCK DIAGRAM G13 HP-MUTE 13 VOL DOWN
HP-DET
K16 HP-DET
TU3901 (TUNER UNIT)
FUNCTION CBA UNIT
SCL R12 4 SCL
9-1
SDA T12 3 SDA
AL+3.3V
IC3006 (MEMORY)
1. System Control Block Diagram [TYPE A]
CN3701 CN501
P-ON-H2 TO
6 P-ON-H2 18 POWER SUPPLY
RESET
RESET J15 RESET 4 RESET 20 BLOCK DIAGRAM
IC3009
CN3701 CN501
PROTECT3
X3001 PROTECT3 B13 3 PROTECT3 21 TO
BACKLIGHT-SW
25MHz H15 XIN25 BACKLIGHT-SW E2 5 BACKLIGHT-SW 19 LED BACKLIGHT DRIVE
OSC BACKLIGHT-ADJ BLOCK DIAGRAM
H16 XOUT25 BACKLIGHT-ADJ F3 7 BACKLIGHT-ADJ 17
BACKLIGHT-SW TO
VIDEO/AUDIO
BLOCK DIAGRAM
PL13.9ABLS
IC3005
(MAIN MICRO CONTROLLER)
RS4051
REMOTE
CN3009 SENSOR
USBDP
R10 USBDP CN3101 CN4052
USB JACK USBDN
T10 USBDN KEY-IN1 A15 4 KEY-IN1 6 KEY SWITCH
REMOTE C14 5 REMOTE 5
LED1 D14 LED DRIVE 6 LED1 4 P-ON+5V
Q3501, Q3502
D4051
POWER
AUDIO-MUTE
C1 AUDIO-MUTE
COMP-DET
TO VIDEO/AUDIO N12 COMP-DET
HP-MUTE
BLOCK DIAGRAM G13 HP-MUTE
HP-DET
K16 HP-DET
TU3901 (TUNER UNIT)
9-2
SCL R12 4 SCL
SDA T12 3 SDA
AL+3.3V
IC3006 (MEMORY)
CN3701 CN501
P-ON-H2 TO
6 P-ON-H2 18 POWER SUPPLY
RESET
RESET J15 RESET 4 RESET 20 BLOCK DIAGRAM
IC3009
CN3701 CN501
PROTECT3
X3001 PROTECT3 B13 3 PROTECT3 21 TO
BACKLIGHT-SW
25MHz H15 XIN25 BACKLIGHT-SW E2 5 BACKLIGHT-SW 19 LED BACKLIGHT DRIVE
OSC BACKLIGHT-ADJ BLOCK DIAGRAM
H16 XOUT25 BACKLIGHT-ADJ F3 7 BACKLIGHT-ADJ 17
BACKLIGHT-SW TO
VIDEO/AUDIO
BLOCK DIAGRAM
PL13.9CBLS
VIDEO SIGNAL AUDIO SIGNAL
JK3702
COM-VIDEO-Y/VIDEO-IN
COMPONENT COM-VIDEO-Pb-IN
-Y/VIDEO-IN COM-VIDEO-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
TO DIGITAL
2. Video/Audio Block Diagram
SIGNAL PROCESS
BLOCK DIAGRAM
JK3701
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
9-3
AUDIO(R)-IN
Q3701
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
IC3851
(HEADPHONE AMP)
6dB
JK3703 1 3
HEADPHONE 7 5
JACK 6dB
Q3861
MUTE 2
HP-DET
SP3802 Q3801 AUDIO-MUTE
1
SPEAKER CONTROL LOGIC Q3803 COMP-DET TO SYSTEM CONTROL
R-CH 2 BLOCK DIAGRAM
P-ON+5V HP-MUTE
Q3802 BACKLIGHT-SW
PL13.9ABLVA
VIDEO SIGNAL AUDIO SIGNAL
LCD PANEL
IC3005 (DIGITAL SIGNAL PROCESS)
ASSEMBLY
VGA-HSYNC
A14 HSYNC
VGA-VSYNC
B14 VSYNC
VGA-R-IN
C11
VGA-G-IN
A9 CN3013
VGA-B-IN N16
C7 12 RX0(-)
COM-VIDEO-Y/VIDEO-IN SW A/D N15
C9 CONVERTER 13 RX0(+)
COM-VIDEO-Pb-IN P16
D8 15 RX1(-)
COM-VIDEO-Pr-IN P15
B11 16 RX1(+)
C10 LVDS TX R16 18 RX2(-)
TO
VIDEO/AUDIO R15 19 RX2(+)
BLOCK DIAGRAM DIF-OUT1 R14 24 RX3(-)
A12 DEMODULATOR
DIF-OUT2 T14 25 RX3(+)
B12 /MPEG DECODER
T16 21 RXCLK(-)
IF-AGC
A16 IF-AGC T15 22 RXCLK(+)
AUDIO(L)-IN
A8
AUDIO(R)-IN
B8
SPDIF
N10 AUDIO I/F
AMP(L)-OUT
B7
AMP(R)-OUT
A7
JK3004
HDMI-IN1 IC3018 (HDMI SW) AUDIO
DECODER
TMDS-D0(+)
7 42
TMDS-D0(-) DIGITAL
9 41 SIGNAL
TMDS-D1(+)
4 45 26 B4 PROCESS
TMDS-D1(-)
6 44 27 A4
TMDS-D2(+)
9-4
1 48 23 B3
TMDS-D2(-)
3 47 24 A3 HDMI
TMDS-CLOCK(+)
10 39 20 B2 I/F
TMDS-CLOCK(-)
12 38 21 A2
HDMI-DATA
16 36 17 B1
HDMI-CLOCK
15 37 18 A1
2 SCL1 SCL2 15
3 SDA1 SDA2 14
10 SCL3 SCL0 7 G14 HDMI-SCL
11 SDA3 SDA0 6 F14 HDMI-SDA
TO VGA-SCL
VIDEO/AUDIO VGA-SDA DIGITAL MAIN CBA UNIT
BLOCK DIAGRAM
PL13.9ABLD
VIDEO SIGNAL AUDIO SIGNAL
LCD PANEL
IC3005 (DIGITAL SIGNAL PROCESS)
ASSEMBLY
VGA-HSYNC
A14 HSYNC
VGA-VSYNC
B14 VSYNC
VGA-R-IN
C11
VGA-G-IN CN3006
A9
VGA-B-IN N16 21 ML1(+)
C7
COM-VIDEO-Y/VIDEO-IN SW A/D N15 20 ML1(-)
C9 CONVERTER
COM-VIDEO-Pb-IN P16 19 ML2(+)
D8
COM-VIDEO-Pr-IN P15 18 ML2(-)
B11
C10 LVDS TX T16 13 ML3(+)
TO
VIDEO/AUDIO T15 12 ML3(-)
BLOCK DIAGRAM DIF-OUT1 R14 11 ML4(+)
A12 DEMODULATOR
DIF-OUT2 T14 10 ML4(-)
B12 /MPEG DECODER
R16 16 MLCLK(+)
IF-AGC
A16 IF-AGC R15 15 MLCLK(-)
AUDIO(L)-IN
A8
AUDIO(R)-IN
B8
SPDIF
N10 AUDIO I/F
AMP(L)-OUT
B7
AMP(R)-OUT
A7
JK3004
HDMI-IN1 IC3018 (HDMI SW) AUDIO
DECODER
TMDS-D0(+)
7 42
TMDS-D0(-) DIGITAL
9 41 SIGNAL
TMDS-D1(+)
4 45 26 B4 PROCESS
TMDS-D1(-)
9-5
6 44 27 A4
TMDS-D2(+)
1 48 23 B3
TMDS-D2(-)
3 47 24 A3 HDMI
TMDS-CLOCK(+)
10 39 20 B2 I/F
TMDS-CLOCK(-)
12 38 21 A2
HDMI-DATA
16 36 17 B1
HDMI-CLOCK
15 37 18 A1
TMDS-D1(-) TMDS-D1(-)
6 10 59 6 IC3002
TMDS-D2(+) TMDS-D2(+) (DDR2 SDRAM)
1 14 63 1
TMDS-D2(-) TMDS-D2(-)
3 13 62 3
TMDS-CLOCK(+) TMDS-CLOCK(+) N4,N7,N8,P3,P4, B1,B9,C2,C8,
10 5 54 10 D1,D3,D7,D9,
TMDS-CLOCK(-) TMDS-CLOCK(-) P6-P8,R3,R4,R6,
12 4 53 12 R8,T2-T5 F1,F9,G2,G8, DATA(0-15)
HDMI-DATA HDMI-DATA H1,H3,H7,H9
16 1 51 16
HDMI-CLOCK HDMI-CLOCK M2,M3,M7,M8,
15 2 52 15 H1,H2,J1,J2,J4,K1, N2,N3,N7,N8, ADDRESS(0-12)
K3,L1,L2,M1-M3,N1 P2,P3,P7,P8,R2
IC3011
(HDMI SERIAL EEPROM)
2 SCL1 SCL2 15
3 SDA1 SDA2 14
10 SCL3 SCL0 7 G14 HDMI-SCL
11 SDA3 SDA0 6 F14 HDMI-SDA
TO VGA-SCL
VIDEO/AUDIO VGA-SDA DIGITAL MAIN CBA UNIT
BLOCK DIAGRAM
PL13.9DBLD
LCD PANEL
ASSEMBLY
P-ON+21V
Q1001
IC1001
(LED BACKLIGHT DRIVER)
4 OVP
CN1001
9 4 VLED
8 DRIVE 2 6 ILED1
BACKLIGHT-SW CONTROL
TO 6 7 ILED1
BACKLIGHT-ADJ LOGIC
SYSTEM CONTROL 1 DRIVE 5 2 ILED2
BLOCK DIAGRAM PROTECT3
14 1 ILED2
9-6
4. LED Backlight Drive Block Diagram
PL13.9ABLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
CN501 CN3701
AC601
AC CORD F602 L601 L602 D601- D604 T601 6-9 AMP+13V 15-18 AMP+13V
CN601 2.5A/250V 16 AL+3.3V 8 AL+3.3V
B LINE LINE BRIDGE 6 7 1-4 P-ON+21V 20-23 P-ON+21V
W FILTER FILTER RECTIFIER
Q650
4 10 RESET
2
11
5. Power Supply Block Diagram
1 12 P-ON+21V
9-7
Q601
SWITCHING
Q656, Q658
+3.3V REG.
Q621
OVER RESET TO
VOLTAGE P-ON-H2 SYSTEM CONTROL
PROTECT IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL13.9ABLP
IC3101
(MAIN MICRO CONTROLLER)
CN3706
TX(+)
AD6 TX(+)
TX(-)
ETHERNET AE6 TX(-) RS4051 P-ON+5V
JACK RX(+)
AC7 RX(+) REMOTE
RX(-)
AC8 RX(-) SENSOR
D4051
POWER
CN3704 CN3105 CN4001
USB0(+) IC4001
M24 USB0(+) REMOTE U3 5 REMOTE 5 (TOUCH SENSOR)
USB JACK USB0(-) Q3101
N22 USB0(-) LED1 V3 LED DRIVE 6 LED1 4
STM-SCL AC2 2 SCL 8 4 SCL POWER 16 POWER
STM-SDA AC1 1 SDA 9 5 SDA SOURCE 17 CH UP
KEY-IN1 U1 4 KEY-IN1 6 1 POWER
MENU 18 CH DOWN
CN3701
USB1(+) 2 CH UP CH UP 19 SOURCE
WIRELESS L23 USB1(+)
USB1(-) CH DOWN 21 MENU
LAN MODULE M22 USB1(-) 3 CH DOWN
[TYPE B, TYPE E, TYPE F]
13 VOL DOWN
VGA-SCL
Y7 VGA-SCL
VGA-SDA FUNCTION CBA UNIT
AD3 VGA-SDA
TO VIDEO/AUDIO LCD-P-ON
W2 LCD-P-ON
9-8
BLOCK DIAGRAM COMP-DET
H6 COMP-DET
HP-DET
L2 HP-DET
P-ON-H2 TO
P-ON-H2 Y2 6 P-ON-H2 18 POWER SUPPLY
RESET
SCL 4 Y15 TU-SCL STB-RESET AD5 RESET 4 RESET 20 BLOCK DIAGRAM
SDA 3 AA16 TU-SDA IC3601
CN3601 CN501
PROTECT3
PROTECT3 T2 3 PROTECT3 21 TO
BACKLIGHT-SW
BACKLIGHT-SW W3 5 BACKLIGHT-SW 19 LED BACKLIGHT DRIVE
BACKLIGHT-ADJ BLOCK DIAGRAM
BACKLIGHT-ADJ P7 7 BACKLIGHT-ADJ 17
X3101
25MHz AE4 AXI
OSC AD4 AXO
PL13.9BBLS
IC3101
(MAIN MICRO CONTROLLER)
CN3706
TX(+)
AD6 TX(+)
TX(-)
ETHERNET AE6 TX(-) RS4051
JACK RX(+)
AC7 RX(+) REMOTE
RX(-)
AC8 RX(-) SENSOR
CN3701 P-ON+5V
IC3103 (MEMORY)
USB1(+)
WIRELESS L23 USB1(+) D4051
USB1(-)
LAN MODULE M22 USB1(-) STM-SCL AC2 6 SCL POWER
STM-SDA AC1 5 SDA
9-9
W2 LCD-P-ON
BLOCK DIAGRAM COMP-DET
H6 COMP-DET
HP-DET
L2 HP-DET
X3101
25MHz AE4 AXI POWER SUPPLY CBA
OSC AD4 AXO
[TYPE E]
PL13.9EBLS
VIDEO SIGNAL AUDIO SIGNAL
JK3701
COM-VIDEO-Y/VIDEO-IN
COMPONENT COM-VIDEO-Pb-IN
-Y/VIDEO-IN COM-VIDEO-Pr-IN
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
TO DIGITAL
2. Video/Audio Block Diagram
SIGNAL PROCESS
JK3706 BLOCK DIAGRAM
AUDIO(L)-IN
AUDIO(L)-IN AUDIO(R)-IN
AUDIO(R)-IN
9-10
Q3709
SPDIF
DIGITAL BUFFER
AUDIO-OUT
(COAXIAL)
HP(R)
JK3801 HP(L)
HEADPHONE
JACK
25 DRIVE AMP(L)-OUT
PWM POWER 3
LOGIC LIMIT
CN3801 23 DRIVE
SP3801 SP(L)+ 1
SPEAKER SP(L)- 2
L-CH 18 DRIVE AMP(R)-OUT
PWM POWER 12
SP(R)+ 4 LIMIT
LOGIC
SP(R)- 3 20 DRIVE VGA-SCL
Q3821
VGA-SDA
1 P-ON+3.3V
CONTROL LOGIC LCD-P-ON TO SYSTEM CONTROL
2
SP3802 COMP-DET BLOCK DIAGRAM
SPEAKER HP-DET
R-CH Q3822
PL13.9BBLVA
LCD PANEL
VIDEO SIGNAL AUDIO SIGNAL ASSEMBLY
9-11
CLOCK(-)
12 AC22
HDMI-DATA
16 W6 IC3401
HDMI-CLOCK
15 T7 (DDR3 SDRAM)
MMDQ(0-31)
JK3715 DATA(0-15)
DATA0(+) HDMI
7 W23 I/F ADDESS(0-14)
DATA0(-) MMA(0-14)
9 W22 IC3402
DATA1(+)
4 V23 HDMI SW (DDR3 SDRAM)
DATA1(-)
6 V22 DATA(16-31)
DATA2(+)
1 U23
HDMI-IN2 DATA2(-) ADDESS(0-14)
3 V24
CLOCK(+)
10 Y25
CLOCK(-) IC3102
12 Y24
HDMI-DATA (NAND FLASH MEMORY)
16 AA5
HDMI-CLOCK MMCDAT(0-7)
15 V7 VIDEO DATA(0-7)
DECODER
JK3716
DATA0(+)
7 AB24
DATA0(-)
9 AC25
DATA1(+)
4 AA23
DATA1(-)
6 AB25
3. Digital Signal Process Block Diagram [TYPE B, TYPE F]
DATA2(+)
1 Y23
HDMI-IN3 DATA2(-)
3 AA24
CLOCK(+)
10 AC24
CLOCK(-)
12 AD25
HDMI-DATA
16 AE3
HDMI-CLOCK
15 R9
DIGITAL MAIN CBA UNIT
PL13.9BBLD
LCD PANEL
VIDEO SIGNAL AUDIO SIGNAL ASSEMBLY
9-12
CLOCK(+)
10 AD22
CLOCK(-)
12 AC22
HDMI-DATA
16 W6 IC3401
HDMI-CLOCK
15 T7 (DDR3 SDRAM)
MMDQ(0-31)
JK3715 DATA(0-15)
DATA0(+) HDMI
7 W23 I/F ADDESS(0-14)
DATA0(-) MMA(0-14)
9 W22 IC3402
DATA1(+)
4 V23 HDMI SW (DDR3 SDRAM)
DATA1(-)
6 V22 DATA(16-31)
DATA2(+)
1 U23
HDMI-IN2 DATA2(-) ADDESS(0-14)
3 V24
CLOCK(+)
10 Y25
3. Digital Signal Process Block Diagram [TYPE E]
CLOCK(-) IC3102
12 Y24
HDMI-DATA (NAND FLASH MEMORY)
16 AA5
HDMI-CLOCK MMCDAT(0-7)
15 V7 VIDEO DATA(0-7)
DECODER
JK3716
DATA0(+)
7 AB24
DATA0(-)
9 AC25
DATA1(+)
4 AA23
DATA1(-)
6 AB25
DATA2(+)
1 Y23
HDMI-IN3 DATA2(-)
3 AA24
CLOCK(+)
10 AC24
CLOCK(-)
12 AD25
HDMI-DATA
16 AE3
HDMI-CLOCK
15 R9
DIGITAL MAIN CBA UNIT
PL13.9EBLD
LCD PANEL
ASSEMBLY
P-ON+21V
Q1001
IC1001
(LED BACKLIGHT DRIVER)
4 OVP
CN1001
9 4 VLED
8 DRIVE 2 6 ILED1
BACKLIGHT-SW CONTROL
TO 6 7 ILED1
BACKLIGHT-ADJ LOGIC
SYSTEM CONTROL 1 DRIVE 5 2 ILED2
BLOCK DIAGRAM PROTECT3
9-13
14 1 ILED2
4. LED Backlight Drive Block Diagram
PL13.9ABLBD
CAUTION !
NOTE:
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, The voltage for parts in hot circuit is measured using
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. hot GND as a common terminal.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
CN501 CN3601
AC601
AC CORD F602 L601 L602 D601- D604 T601 6-9 AMP+13V 15-18 AMP+13V
CN601 2.5A/250V 16 AL+3.3V 8 AL+3.3V
B LINE LINE BRIDGE 6 7 1-4 P-ON+21V 20-23 P-ON+21V
W FILTER FILTER RECTIFIER
Q650
4 10 RESET
2
11
5. Power Supply Block Diagram
1 12 P-ON+21V
9-14
Q601
SWITCHING
Q656, Q658
+3.3V REG.
Q621
OVER RESET TO
VOLTAGE P-ON-H2 SYSTEM CONTROL
PROTECT IC602 BLOCKDIAGRAM
ERROR
VOLTAGE DET
4 1
Q602
SWITCHING
3 2
CONTROL
Q653
HOT COLD
POWER SUPPLY CBA
PL13.9BBLP
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in μF
(P = 10-6 μF).
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire PL13.9 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the PL13.9 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
10-1 PL13.9SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
1 2 3
(Unit: Volt) 5.0 5.0 Power on mode
10-2 PL13.9SC
Power Supply Schematic Diagram [TYPE A, TYPE B, TYPE C, TYPE F]
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, NOTE:
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. The voltage for parts in hot circuit is measured using
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
4 AC CORD CN601
W
B
F602 R601
1.2M/1/2W
WIRE C1009
1/100V
C1008
1/100V
C1007
1/100V
C1006
47/100V
C1005
47/100V C1018
OPEN 15.7 D
BEAD
Q1001
AP18T10AGH-HF
G (SWITCHING)
3.0
HSC119
R1008
10 GP001
EARTH PLATE
2.5A/250V C603 R1009
1000P/250V 0.1 S 200
F601 SA601 R1011
OPEN VARISTOR 470K R1021 R1020 C1010
OPEN 0.18/1W OPEN GP002
C602 EARTH PLATE
1000P/250V R1012
C604 510K R1022
0.22/275V OPEN
2.5A250V C616 IC1001
1000P/250V C1017 R1013 HA7219PB
L601 1000P 27K R1023
LED BACKLIGHT OPEN
LINE FILTER DRIVER
JS601 JS602 R1003
OPEN 3.0 1 1K
OPEN SA602 GT601 14 3.4
JS603 OPEN OPEN D655 R1010 C1014
OPEN SB3A0BH 0.5 2 1.7 100 1
C614 DRIVE COMP 13
0.22/275V D601 D604 JS604
1N5397BD 1N5397BD OPEN D655A 1.2 3 ISET VIN 12 18.0
OPEN
R602 0 C1013 R1002 R1001
2.7/5W D653 1.3 4 OVP GND 11 0.1 360 360
L602 SB3A0BH C1012
JS605 LINE FILTER JS606 0.5 5 DRIVE 5.0 4.7
OPEN OPEN D653A LDO 10
D602 D603 OPEN
3 1N5397BD 1N5397BD
R1016
6.2K
2.9 6
1.0 7 RT
R1014
CONTROL
LOGIC 9 3.0
8
0.1
C1011
100K 1000P
T601 R1006
POWER TRANS 10K
6 7 R1004
C605 R1007 R1005 10K
R614 330 3.4 Q650 100K 100K
470K /200V R651 D656 D657 R652 KTC3875S
1 RS1BJTD MM5Z11B 56K -3.1 -Y-RTK/P
R603 BC604 5 8
470K WIRE C656 R693 (RESET) TO LCD PANEL
1/50V OPEN 0 CN1001 ASSEMBLY
R604 0.5 1 ILED2
470K BC601 9
WIRE C650 D658 R691 C1015 R1017 0.5 2 ILED2
4 OPEN OPEN OPEN Q659 OPEN 0
OPEN 3 NU
10 R1019
192.0 D Q601 D651 R653 R692 OPEN 49.5 4 VLED
TK7P60W SB3150BH 33K OPEN
C608 R606 R607
G (SWITCHING) 0.022 330 330 D651A R1018
0
5 NU
2.6 2 11 OPEN 0.5 6 ILED1
0.1 S Q602 Q657 C1016 0.5 7 ILED1
2SC5344SY D650 R688 R689 OPEN R685 R686 R687 OPEN
C607 SWITCHING SB3150BH OPEN OPEN OPEN OPEN OPEN
1800P CONTROL R608 D605 1 12
2.6 1.5K MM5Z4V3B
0.4 D650A IC651
OPEN C651 C652 C653 D652 D652A
GND
OUT
D621 D610
IN
Q621 HSC119 HSC119 D405
1 2 3 OPEN TO DIGITAL MAIN
KTC3875S CBA UNIT CN3601
-Y-RTK/P R613 CN501 or CN3701
C611 C606 D607A D607 OVER 180 R676 R678 R679 R683 R684 0 23
OPEN TFZVTR27B OPEN OPEN OPEN OPEN OPEN OPEN D406 NU
820P VOLTAGE OPEN
/2KV 0.4 PROTECT R621 D623 0 22 PROTECT1
560 MM5Z30B C662 C664
0.4 R622 Q658 OPEN OPEN C633 3.4 21 PROTECT3
C623 C624 2SA950-O OPEN
0 0 4.7 OPEN IC602 3.4 20 RESET
TLP781F R690 (+3.3V REG.)
2.7 14.4 3.4 C636 3.3 19 BACKLIGHT-SW
ERROR OPEN
VOLTAGE DET R655 R654 C630 C632 3.3 18 P-ON-H2
R623 C622 C621 13.0 20.0 180 180 OPEN OPEN
10K 10 OPEN 4 1 R673 13.8 3.3 17 BACKLIGHT-ADJ
D609A R609 C610 R657 OPEN 13.8 3.4 3.4 16
CES520 100 100P 3.9K AL+3.3V
0.4 19.0 Q656 0 15
3 2 KTC3875S-Y-RTK/P C663 C661 D664 C631 GND
3.9 (+3.3V REG.) R662 100/10V 1 TFZVTR4.7B OPEN 0 14
R611 D608A D608 R615 C609 R612 C666 R659 R675 3.3K GND
OPEN 1ZB36BB 0.068 5.6K 0.22 27K 68K 0 13
0.36 OPEN GND
/2W R660 R674 R667 R680 D663
C660 R658 3.9K 0 8.2K 100 OPEN 0 12 GND
R616 IC601 0.22 2.7K C665 R682
OPEN D661 0.1 0 R677 0 11 GND
OPEN 19.0 2.5 HSC119 R670 R671 R672 10K 0 10
4 1 270 270 270 GND
R617 0 D660
SL431A-AT
R661
3.3K 3.9
14.4 9 AMP+13V
OPEN 2.5 14.4 8
C635 C638 AMP+13V
1
3 2
R618 0 D662
SL431A-AT R681 OPEN OPEN 14.4 7 AMP+13V
OPEN 10K 14.4 6
BC602 0 R669 AMP+13V
BEAD Q653 0.6 10K 0 5 GND
R619 KTC3875S-Y-RTK/P 20.4
BC603 OPEN (SWITCHING) 0 R668 4 P-ON+21V
BEAD 47K 20.4
C639 3 P-ON+21V
OPEN 20.4 2 P-ON+21V
20.4 1
HOT COLD P-ON+21V
A B C D E F G
10-3 PL13.9ASCP
Power Supply Schematic Diagram [TYPE D, TYPE E]
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, NOTE:
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse. The voltage for parts in hot circuit is measured using
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V hot GND as a common terminal.
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail.
4 AC CORD CN601
W
B
F602 R601
1.2M/1/2W
WIRE C1009
1/100V
C1008
1/100V
C1007
1/100V
C1006
47/100V
C1005
47/100V C1018
OPEN 15.7 D
BEAD
Q1001
AP18T10AGH-HF
G (SWITCHING)
3.0
HSC119
R1008
10 GP001
OPEN
2.5A/250V C603 R1009
1000P/250V 0.1 S 200
F601 SA601 R1011
OPEN VARISTOR 470K R1021 R1020 C1010
OPEN 0.18/1W OPEN GP002
C602 OPEN
1000P/250V R1012
C604 510K R1022
0.22/275V OPEN
2.5A250V C616 IC1001
1000P/250V C1017 R1013 HA7219PB
L601 1000P 27K R1023
LED BACKLIGHT OPEN
LINE FILTER DRIVER
JS601 JS602 R1003
OPEN 3.0 1 1K
OPEN SA602 GT601 14 3.4
JS603 OPEN OPEN D655 R1010 C1014
OPEN SB3A0BH 0.5 2 1.7 100 1
C614 DRIVE COMP 13
0.22/275V D601 D604 JS604
1N5397BD 1N5397BD OPEN D655A 1.2 3 ISET VIN 12 18.0
OPEN
R602 0 C1013 R1002 R1001
2.7/5W D653 1.3 4 OVP GND 11 0.1 360 360
L602 SB3A0BH C1012
JS605 LINE FILTER JS606 0.5 5 DRIVE 5.0 4.7
OPEN OPEN D653A LDO 10
D602 D603 OPEN
3 1N5397BD 1N5397BD
R1016
6.2K
2.9 6
1.0 7 RT
R1014
CONTROL
LOGIC 9 3.0
8
0.1
C1011
100K 1000P
T601 R1006
POWER TRANS 10K
6 7 R1004
C605 R1007 R1005 10K
R614 330 3.4 Q650 100K 100K
470K /200V R651 D656 D657 R652 KTC3875S
1 RS1BJTD MM5Z11B 56K -3.1 -Y-RTK/P
R603 BC604 5 8
470K WIRE C656 R693 (RESET) TO LCD PANEL
1/50V OPEN 0 CN1001 ASSEMBLY
R604 0.5 1 ILED2
470K BC601 9
WIRE C650 D658 R691 C1015 R1017 0.5 2 ILED2
4 OPEN OPEN OPEN Q659 OPEN 0
OPEN 3 NU
10 R1019
192.0 D Q601 D651 R653 R692 OPEN 49.5 4 VLED
TK7P60W SB3150BH 33K OPEN
C608 R606 R607
G (SWITCHING) 0.022 330 330 D651A R1018
0
5 NU
2.6 2 11 OPEN 0.5 6 ILED1
0.1 S Q602 Q657 C1016 0.5 7 ILED1
2SC5344SY D650 R688 R689 OPEN R685 R686 R687 OPEN
C607 SWITCHING SB3150BH OPEN OPEN OPEN OPEN OPEN
1800P CONTROL R608 D605 1 12
2.6 1.5K MM5Z4V3B
0.4 D650A IC651
OPEN C651 C652 C653 D652 D652A Q657A
GND
OUT
D621 D610
IN
Q621 HSC119 HSC119 D405
1 2 3 OPEN TO DIGITAL MAIN
KTC3875S CBA UNIT CN3601
-Y-RTK/P R613 CN501 or CN3701
C611 C606 D607A D607 OVER 180 R676 R678 R679 R683 R684 0 23
OPEN TFZVTR27B OPEN OPEN OPEN OPEN OPEN OPEN D406 LED-CONT(NU)
820P VOLTAGE OPEN
/2KV 0.4 PROTECT R621 D623 0 22 PROTECT1
560 MM5Z30B C662 C664
0.4 R622 Q658 OPEN OPEN C633 3.4 21 PROTECT3
C623 C624 2SA950-O OPEN
0 0 4.7 OPEN IC602 Q658A 3.4 20 RESET
TLP781F R690 OPEN (+3.3V REG.)
1.5 14.4 3.4 C636 3.3 19 BACKLIGHT-SW
ERROR OPEN
VOLTAGE DET R655 R654 C630 C632 3.3 18 P-ON-H2
R623 C622 C621 13.0 20.0 180 180 OPEN OPEN
10K 10 OPEN 4 1 R673 13.8 3.3 17 BACKLIGHT-ADJ
D609A R609 C610 R657 OPEN 13.8 3.4 3.4 16
CES520 100 100P 3.9K AL+3.3V
0.4 19.0 Q656 0 15
3 2 KTC3875S-Y-RTK/P C663 C661 D664 C631 GND
3.9 (+3.3V REG.) R662 100/10V OPEN TFZVTR4.7B OPEN 0 14
R611 D608A D608 R615 C609 R612 C666 R659 R675 3.3K GND
OPEN 1ZB36BB 0.068 5.6K 0.22 27K 68K 0 13
0.36 OPEN GND
/2W R660 R674 R667 R680 D663
C660 R658 3.9K 0 8.2K 100 OPEN 0 12 GND
R616 IC601 0.22 2.7K C665 R682
OPEN D661 0.1 0 R677 0 11 GND
OPEN 19.0 2.5 HSC119 R670 R671 R672 10K 0 10
4 1 270 270 270 GND
R617 0 D660
SL431A-AT
R661
3.3K 3.9
14.4 9 AMP+13V
OPEN 2.5 14.4 8
C635 C638 AMP+13V
1
3 2
R618 0 D662
SL431A-AT R681 OPEN OPEN 14.4 7 AMP+13V
OPEN 10K 14.4 6
BC602 0 R669 AMP+13V
BEAD Q653 0.6 10K 0 5 GND
R619 KTC3875S-Y-RTK/P 20.4
BC603 OPEN (SWITCHING) 0 R668 4 P-ON+21V
BEAD 47K 20.4
C639 3 P-ON+21V
OPEN 20.4 2 P-ON+21V
20.4 1
HOT COLD P-ON+21V
A B C D E F G
10-4 PL13.9DSCP
Function Schematic Diagram [TYPE A, TYPE B]
VOUT
POWER IC4051 6 KEY-IN1
VCC
GND
OPEN 7 GND
3 2 1 1 OUT NU 6 8 SCL
C4058 R4057 2 GND NU 5 9 SDA
R4051 D4053 OPEN OPEN
56 OPEN
R4054 3 VCC NU 4
1K R4053 D4052 C4057 R4058 R4056
1K OPEN OPEN OPEN OPEN
C4051 C4056 C4052 C4055
10 10 1000P OPEN
C4053
0.1
2 18
CH DOWN
17
CH UP
16 15 14 13 R4008
18K
POWER
GND
GND
R4007
560
SOURCE 19 VOL DOWN 12
R4009
SOURCE VOL UP 8.2K
20 VDD MENU 11
R4006
C4001 560
1 MENU 21 MENU NU 10
R4004
560 R4017
VOL UP 22 VOL UP GND 9 OPEN
R4002
560
VOL DOWN 23 VOL DOWN GND 8 R4010
4.7K
CH DOWN
SOURCE
24 NU NU 7
POWER
CH UP
C4002
SCL
SDA
2200P
1 2 3 4 5 6
IC4001
CY8C20324
-12LQXIT/CP R4011
(TOUCH SENSOR) 2.7K
R4012
2.2K
R4014 R4013
2.2K 100
1 R4021
10
R4022
10
A B C D
10-5 PL13.9SCF
Function Schematic Diagram [TYPE C, TYPE D, TYPE E, TYPE F]
2 D4051
SMLE12WBC7W1HR
POWER IC4051
R4055
OPEN
R4059
OPEN
3
4
5
LIGHT
LED1
REMOTE
6 KEY-IN1
OPEN
7 GND
1 OUT NU 6 8 SCL(NU)
RS4051 R4057 2 GND NU 5 9 SDA(NU)
RS-272 OPEN
(REMOTE SENSOR) 3 VCC NU 4
C4057 R4058 R4056
VOUT
1 R4001
18K
R4002
8.2K
R4003
4.7K
R4004
2.7K
R4005
2.2K
R4006
2.2K
D4002 D4001 C4002
OPEN SW4001 SW4002 SW4003 SW4004 SW4005 SW4006 SW4007 MM5Z5V6B 0.1
VOL VOL CH CH UP MENU SOURCE POWER
DOWN UP DOWN
A B C
10-6 PL13.9CSCF
Digital Main 1 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
R3085 DIGITAL 4
OPEN
DIGITAL MAIN CBA UNIT P-ON+5V
P-ON+21V
TO LCD PANEL R3630
ASSEMBLY CN3013 OPEN P-ON+3.3V
R3045 R3047 R3046 C3057 C3058 R3039
LCD+12V 1 OPEN OPEN OPEN OPEN OPEN OPEN PROTECT3
R3044 D3008
LCD+12V 2 C3166 C3167 OPEN OPEN CONTINUE
OPEN OPEN DIGITAL 3
LCD+12V 3
LCD+12V 4 R3048 CELL-PWR-CTRL
Q3007 OPEN
GND 5 OPEN VCOM-PWM
4 GND
GND
NU
6
7
8
R3632
OPEN
D3624
OPEN
C3000
OPEN
R3037 R3038
C3514
OPEN
CN3006 (NO CONNECTION)
30 LCD+21V
29 LCD+21V
SELLVDS 9 R3135 OPEN OPEN 28 GND
OPEN R3622 27 VCOM-PWM
NU 10 100
GND 11 26 PWR-CTRL
R3621 C3628 R3035 25 P-ON+3.3V
RX0(-) 12 10K OPEN OPEN
C3624 C3623 C3622 C3621 C3512 24 GND
RX0(+) 13 0.1 OPEN OPEN 4.7 R3524 OPEN
IC3621 D3623 OPEN 23 ML0(+)
GND 14 OPEN
MP1472GJC452Z 22 ML0(-)
RX1(-) 15 (SW+12V)
C3627 21 ML1(+)
RX1(+) 16 0.047
1 SS BST 8 R3028 20 ML1(-)
GND 17 C3625 R3627 OPEN
OPEN OPEN 19 ML2(+)
RX2(-) 18 2 EN IN 7
C3629 R3623 C3626 18 ML2(-)
RX2(+) 19 1000P 24K 0.1
3 COMP SW 6 17 GND
GND 20 C3630
RXCLK(-) 21 4 FB GND 5 OPEN L3621 16 MLCLK(+)
R3625 R3624 33uH 15 MLCLK(-)
RXCLK(+) 22 120K 1K R3626 R3628
10K OPEN 14 GND
GND 23
RX3(-) 24 13 ML3(+)
RX3(+) 25 R3631 R3629 D3622 D3621 C3636 C3635 C3634 C3633 C3632 C3631 12 ML3(-)
3 GND
BIST
NU
26
27
28 R3161
OPEN
R3162
OPEN
OPEN
10K 10K OPEN OPEN OPEN 4.7 4.7 4.7 4.7 OPEN 11 ML4(+)
10 ML4(-)
9 ML5(+)
NU 29 8 ML5(-)
GND 30 R3129 7 GND
OPEN 6 TP
R3130 5 POL
(NO CONNECTION) CN3014 OPEN
LCD+12V 30 4 CPV
LCD+12V 29 3 OE1
LCD+12V 28 2 OE2
LCD+12V 27 1 STV
GND 26
CN3001 (NO CONNECTION)
GND 25 31 LCD+21V
C3641 OPEN
C3642 OPEN
C3643 OPEN
C3644 OPEN
C3645 OPEN
C3646 OPEN
C3647 OPEN
OPEN
OPEN
OPEN
OPEN
GND 24 *1
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
30 LCD+21V
NU 23 IC3005(1/6)
R8A05011BG-U0 29 LCD+21V
C3654
C3655
C3648
C3649
C3650
C3651
C3652
C3653
C3656
C3657
C3658
C3659
C3660
C3661
SELLVDS 22 DIGITAL SIGNAL PROCESS 28 GND
NU 21 /MAIN MICRO CONTROLLER
27 VCOM-PWM
GND 20 26 PWR-CTRL
RX0(-) 19 R16 25 P-ON+3.3V
RX0(+) 18
2 GND 17
RX1(-) 16
RX1(+) 15
R15
P14
P13
N16
24
23
22
21
GND
ML0(+)
ML0(-)
ML1(+)
GND 14 N15 20 ML1(-)
RX2(-) 13 LVDS P16 19 ML2(+)
RX2(+) 12 TX
P15 18 ML2(-)
GND 11 T16 17 GND
RXCLK(-) 10 T15 16 MLCLK(+)
RXCLK(+) 9 R14 15 MLCLK(-)
GND 8 T14 14 GND
RX3(-) 7 R13 13 ML3(+)
RX3(+) 6 T13 12 ML3(-)
GND 5 11 ML4(+)
BIST 4 NU M16 10 ML4(-)
NU 3 NU M13 9 ML5(+)
NU 2 TO DIGITAL NU N14 8 ML5(-)
MAIN 2
GND 1 IC3005(2/6) NU N13 7 GND
R3644 OPEN
TP L13 6 TP
(NO CONNECTION) CN3601 R3645 OPEN
GND 1 POL M15 5 POL
R3641 OPEN
1 NU
NU
NU
2
3
4
R3131
OPEN
C3161
OPEN
CPV
OE
OE2
STV
L16
L15
L14
M14
R3642
R3643
R3646
OPEN
OPEN
OPEN
4
3
2
1
CPV
OE1
OE2
STV
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
(NO CONNECTION) CN3602 NU K15
GND 1 R3088
9.1K
R3041
R3117
R3118
R3119
R3120
R3132
C3666
C3662
C3663
C3664
C3665
C3667
NU 2
NU 3
NU 4
A B C D E F
10-7 PL13.9ASCD1
Digital Main 2 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
DIF-OUT1
DIF-OUT2
74LVC1G126GW
IF-AGC
(BUFFER GATE)
+3.3V
GND
SDA
SCL
1 VCC 5
C3214 Q3301
1 2 3 4 5 6 7 2 0.1 RU1L002SNTL
(BUFFER) Q3302
4 C3903 0.1
C3902 0.1
3 GND 4 RU1L002SNTL
(BUFFER)
CONTINUE
DIGITAL 6
VGA-SDA
VGA-SCL
IC3014
74LVC1G126GW
(BUFFER GATE)
1 VCC 5 CONTINUE
L3913 DIGITAL 4
2.2uH
2 P-ON+3.3V
C3905 C3901 D3901 C3934 C3909 C3175 C3176 R3204 P-ON+5V
10 220/6.3V MM5Z5V6B OPEN OPEN 33P 33P 2.7K 3 GND 4
3 MAIN 5
IC3005(5/6) DEMODULATOR
/MPEG
DECODER
A12
C3173
33P
C3172
R3251
10
R3250
R3333
10
R3343
OPEN 13 8 3
2 TO DIGITAL
MAIN 3
NU
NU
B9
D9
C3708 R3701
JK3702
COMPONENT
-Y/VIDEO-IN
DIGITAL IC3005(3/6) 0.1 OPEN
R3711
SIGNAL 10K
PROCESS COMPONENT
TO DIGITAL R3702 -Pb-IN
MAIN 3 OPEN
IC3005(3/6) R3710
100
COMPONENT
C3707 R3712 Q3701 R3703 -Pr-IN
1 10K 2SC4081UBTLQ OPEN
(BUFFER)
R3709 C3706 JK3701
C3335 220 1
TO DIGITAL TO DIGITAL 2.2 C3285 0.1 DIGITAL
NU B10 R3708 C3709 AUDIO-OUT
MAIN 6 MAIN 1 C3286 0.1 110 100P (COAXIAL)
IC3005(6/6) IC3005(1/6) NU A11
C3336 1
NU D10 AUDIO(L)-IN
R3704
100K
AUDIO(R)-IN
R3705
100K CONTINUE
DIGITAL 5
1 SCL
SDA
AUDIO(L)-IN
AUDIO(R)-IN
CONTINUE
DIGITAL 5
SPDIF
G H I J K L
10-8 PL13.9ASCD2
Digital Main 3 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
C3009 R3082 *1
OPEN 100 IC3005(3/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS C3184
R3064 C3050 /MAIN MICRO CONTROLLER 18P
100 0.1
M5 SD-VREF0
R3065 C3051 N3 GND X3001
100 0.1 XIN25 H15 R3223 25MHz C3183
1K 20P CN3012 (NO CONNECTION)
4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
XOUT25 H16
ASEBRKAK-N F15
R3527 OPEN
1
2
3
AL+3.3V
GND
ASEBRKAK-N
K4T51163QJ-BCE7 SD-DQ13 ASEMD0 F16 4 ASEMD0
(DDR2 SDRAM) P7 SD-DQ13 TRST-N E16 5 TRST-N
SD-DQ12 R6 SD-DQ12 R3525 OPEN
C3029 0.1 TCK E15 6 TCK
*A VDD SD-DQ11 P6 SD-DQ11 R3526 OPEN
C3030 0.1 VREF J2 TDI D16 7 TDI
SD-DQ10 N7 SD-DQ10
C3031 0.1 C3010 R3083 TDO D15 8 TDO
0.1 100 SD-DQ9 T5 SD-DQ9
C3032 0.1 TMS E14 9 TMS
CKE K2 SD-DQ8 P8 SD-DQ8 TO DIGITAL
C3033 0.1 MAIN 2 R3522 10 CPU-RESET-N
E2 NU CK J8 SD-DQ7 P4 SD-DQ7 IC3005(2/6) 10K
C3034 0.1
A2 NU CK K8 SD-DQ6 T3 SD-DQ6 R3395 CN3010 (NO CONNECTION)
C3035 0.1 R3049 4.7K
R8 NU CS L8 150 SD-DQ5 R4 SD-DQ5 1 P-ON+5V
C3037 0.1 R3468 100
R7 NU RAS K7 SD-DQ4 T2 SD-DQ4 TXD0 G15 2 UART0-TX
C3038 0.1 R3469 100
R3 NU CAS L7 SD-DQ3 P3 SD-DQ3 RXD0 G16 3 UART0-RX
C3039 0.1 C3253
WE K3 SD-DQ2 T4 SD-DQ2 OPEN 4 GND
C3040 0.1 C3254 C3255 R3396
1-O3 B7 UDQS BA2/NU L1 SD-DQ1 R3 SD-DQ1 OPEN OPEN 4.7K
C3041 0.1
2-O3 A8 UDQS/NU BA1 L3 SD-DQ0 N4 SD-DQ0
C3140 0.1 CONTINUE
3-O3 B3 UDM BA0 L2 3-M3 T6 SD-UDM DIGITAL 2
SD-DQ15 B9 DQ15 A12 R2 6-M3 R5 SD-LDM COMP-DET
R3516 100
SD-DQ12 2-M3 BACKLIGHT-ADJ F3
3 SD-DQ10
SD-DQ9
SD-DQ14
B1
D9
D1
D3
DQ12
DQ10
DQ9
DQ14
A11
A10/AP
A9
A8
P7
M2
P3
P8
1-M3
5-M3
4-M3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
VCOM-PWM F2
GND J14
R3517 OPEN CONTINUE
DIGITAL 5
CPU-RESET-N
SD-DQ13 D7 DQ13 A7 P2
SD-DQ11 C2 DQ11 A6 N7
SD-DQ8 R3030 33x4 H1 SD-A4 R3511 22 CONTINUE
C8 DQ8 A5 N3 CELL-PWR-CTRL D1 DIGITAL 4
4-O3 F7 LDQS A4 N8 H3 SD-CAS GPY10 E13 GPY10
5-O3 E8 LDQS/NU A3 N2 J2 SD-A11 CPU-RESET-N
6-O3 J1 SD-A0 R3211 100
F3 LDM A2 M7 R3031 33x4 P-ON-H2 B16 P-ON-H2
SD-DQ3 J4 SD-A10 R3233 22
F9 DQ3 A1 M3 HP-MUTE G13 BACKLIGHT-ADJ
SD-DQ2 L1 SD-A1 R3188 22
F1 DQ2 A0 M8 BACKLIGHT-SW E2 BACKLIGHT-SW
SD-DQ7 H9 DQ7 ODT K9 K4 SD-BA1
R3503
SD-DQ6 L2 SD-A9 10K CONTINUE
H1 DQ6 R3032 33x4 DIGITAL 1
SD-DQ4 H3 DQ4 L4 SD-WE CELL-PWR-CTRL
SD-DQ1 VSS *B N2 SD-BA0
H7 DQ1 TO DIGITAL VCOM-PWM
SD-DQ5 G2 DQ5 P1 SD-BA2 MAIN 2 R3510 22K
SD-DQ0 M3 SD-A3 IC3005(2/6)
G8 DQ0 CONTINUE
R3033 33x4 M1 SD-A5 DIGITAL 5
R3515 4.7K
M2 SD-A12 LED1 D14 LED1
*A:A1,A9,C1,C3,C7,C9,E1,E9, R3213 22
G1,G3,G7,G9,J1,J9,M9,R1 L3 SD-CKE REMOTE C14 REMOTE
R3217 22
2 *B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9 R3034 33x4
N1
J3
K3
SD-A7
SD-RAS
SD-A6
AUDIO-MUTE C1
R3234
OPEN
K1 SD-A2
CONTINUE
K2 SD-ODT DIGITAL 4
IC3006 H2 SD-A8 R3201 P-ON+1.8V
W25Q32FVSSIG R3102 R3016 33 R3215 22 33K
10K R2 SD-CLK COMP-DET N12 P-ON+3.3V
(MEMORY) R3084 10
R1 SD-CLKN AL+3.3V
1 CS VCC 8 R3087 10
R3107 H4 NU P-ON+5V
10K C3073 R3070 150
2 SO NU 7 0.1
R3089 47
P12 CS
3 WP SCK 6 R3092 47 CONTINUE
R11 SOUT DIGITAL 5
R3093 47
4 GND SI 5 P11 SIN C3072 10 HP-MUTE
R3094 47 NU H14
R3479 T11 SCK AUDIO-MUTE
10K R3095 22
T9 VBUS-EN BACKLIGHT-SW
R9 VBUS-ST
R10 USBDP
(USB JACK) CN3009 C3246 C3348 T10 USBDN
1 220/6.3V R3099 5.6K
BUS-POWER 1 P10 NU
USBDN 2 IC3019
1 USBDP
GND
3
4 L3025
EXC24CG900U
AP2151WG-7
(HIGH SIDE SW)
1 OUT IN 5
C3327
2 GND 1
3 /FLAG RN 4
R3480
10K
DIGITAL MAIN CBA UNIT
M N O P Q R
10-9 PL13.9ASCD3
Digital Main 4 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
*1 DIGITAL 3
IC3005(4/6) R3221 P-ON+1.8V
R8A05011BG-U0 100
DIGITAL SIGNAL PROCESS P-ON+3.3V
/MAIN MICRO CONTROLLER R3222 AL+3.3V
10K L3027
BEAD P-ON+5V
VCC33STB F12
C3160 R3106 R3100 R3036
4 VCC33STB G12
VDD12STB E12
0.1
D
G
S
Q3006
2SA1576UBTLQ
47K
R3105
10K
22K
Q3101
2SC4081UBTLQ
(SWITCHING)
D3105
OPEN D3103
HSC119
R3424
100 IC3004
100
CONTINUE
DIGITAL 6
P-ON+3.3V
(SWITCHING) BD00IA5WEFJ-E2 AL+3.3V
L3030
0 Q3013 Q3005 C3265 R3138 (+1.2V REG.) P-ON+3.3V(1)
C3181 SSM3K309T 2SC4081UBTLQ 10 OPEN
0.1 (SW+12V) R3423 D3115 1 VOUT VCC 8 P-ON+5V
(SWITCHING) R3097 47K HSC119
1.5K C3024 CONTINUE
D3101 2 FB NU 7 10 DIGITAL 2
VDD12 *C HSC119 P-ON+3.3V
R3061 R3060 C3019
C3123 C3124 C3125 C3126 C3132 C3133 D3102 10K 2.7K 0.022 3 GND NU 6 P-ON+5V
1 1 1 1 10 10 HSC119 R3059 R3062
2.7K 1.8K
4 NU EN 5
CONTINUE
C3127 C3128 C3129 C3130 C3134 R3043 C3086 DIGITAL 1
1 1 1 1 1 R3228 R3086 180 10 P-ON+5V
OPEN Q3011 4.7K
OPEN R3008 P-ON+21V
AVDD12 M10 C3237 R3227 D3104 C3131 1
OPEN OPEN HSC119 Q3003 1 P-ON+3.3V
C3135 R3077 2SC4081UBTLQ
0.1 L3021 10K (SWITCHING) PROTECT3
BEAD IC3601
AVDD12 E8 AP2121AK-3.3TRE1 L3003
AVDD12 F8 C3118 C3136 C3114 C3115 R3605 (+3.3V REG.) R3079 Q3004 OPEN
10 1 10 10 0 10K 2SC4081UBTLQ IC3007
AVDD12 F9 1 VIN VOUT 5 (SWITCHING) BD00IC0WEFJ CONTINUE
C3609 C3610 (+1.8V REG.) DIGITAL 5
1 2 GND R3606 1 RESET
3 VDDCLK G11
C3139
0.1
R3608
4.7K
C3611 R3609
OPEN OPEN
3 CE NU 4
OPEN
R3607
OPEN
D3106
HSC119 R3111
10K
R3110
10K
C3075
0.022
1 VOUT
2 FB
VCC 8
NU 7
C3069
10
C3068
OPEN
PROTECT1
PROTECT3
3 GND NU 6
R3109 R3103 CONTINUE
3.3K 1.8K DIGITAL 5
VCCQ18 H5 4 NU EN 5
P-ON+3.3V
VCCQ18 J5 C3326 C3325 C3324 C3343 C3264 C3079 C3087
10 OPEN OPEN 10 OPEN 220/6.3V 10 CHECK+1.8V
VCCQ18 M4 AL+3.3V
VCCQ18 T1 P-ON+5V
C3322 C3321 C3320 C3319 C3318
VCCQ18 M6 10 OPEN 10 10 10 P-ON+3.3V(1)
VCCQ18 N6 AMP+13V
VCCQ18 M7 C3141 C3142 C3143 C3144 C3145 C3080 C3103 C3007 C3102 C3003 C3002
1 1 1 1 1 4.7 OPEN 0.1 IC3008 4.7 0.1 OPEN IC3001
VCCQ18 M8 MP1472GJC452Z MP1472GJC452Z
L3019 (+1.2V REG.) (+3.3V REG.)
OPEN C3083 C3013
AVDD33 E10 0.015 0.047 CONTINUE
C3148 C3149 C3150 D3113 1 SS BST 8 1 SS BST 8 DIGITAL 3
AVDD33 C2 1 10 1 MM5Z5V6B R3133 C3091 R3091 C3092 GPY10
10K OPEN C3085 0 OPEN C3014
AVDD33 C3 2 EN IN 7 R3141 0.1 2 EN IN 7 R3057 0.1 CPU-RESET-N
C3090 C3088 R3137 OPEN C3119 C3017 R3001 OPEN
AVDD33 E11 1 4700P 2.7K OPEN 2200P 8.2K P-ON-H2
3 COMP SW 6 3 COMP SW 6
BACKLIGHT-ADJ
L3026 4 FB GND 5 4 FB GND 5
BEAD L3009 L3002 BACKLIGHT-SW
AVDD33 D6 10uH 33uH
2 L3006
BEAD
C3151
1
C3152
1
C3154
1
D3114
MM5Z5V6B C3099 R3142 R3149 C3094 C3096 C3065 C3097 R3602 D3005 R3004 C3020 C3021 C3059 R3014 R3601
OPEN
OPEN OPEN 3.9K 330/4V 10 10 OPEN OPEN PTZTE255.1B 33K 330/4V 10 10 270 OPEN
220
100
100
100
AVDD33 E6 R3145 C3606 R3003 C3605
C3155 C3156 1.2K OPEN 6.2K OPEN
1 1
R3013
R3011
R3009
R3072
R3068
D3006 R3143 R3002 TO POWER SUPPLY
VCCQ33 G4 PTZTE255.1B 15K 15K CN3701 CBA CN501
VCCQ33 F5 C3157 C3158 C3159 1 NU
1 1 1 D3994 OPEN
VCCQ33 L12 2 PROTECT1
D3995 OPEN
VCCQ33 K13 C3022 C3001 C3105 R3108 D3112 D3107 3 PROTECT3
4.7 0.1 OPEN 47K MM5Z12B HSC119
VCCQ33 J12 4 RESET
AVDD33 N11 R3140 5 BACKLIGHT-SW
IC3003 18K Q3009
MP1472GJC452Z 2SC4081UBTLQ 6 P-ON-H2
C3028 (+5V REG.) R3112 R3115 Q3103 C3238 R3139 (SWITCHING) 7 BACKLIGHT-ADJ
VSS *D 0.047 10K OPEN 2SA1576UBTLQ R3101 OPEN 1K
1 SS BST 8 (SWITCHING) 1K 8 AL+3.3V
R3098 C3095 C3063 C3994 9 GND
0 OPEN C3042 OPEN OPEN
*C:G5,G6,H6,J7,J11,J13,K6,K7, 2 EN IN 7 R3054 0.1 Q3102 C3107 R3104 10 GND
K11,L8,L9,M9,M11,N9,P9. C3121 C3043 R3005 OPEN 2SC4081UBTLQ 1 1K
OPEN 4700P 4.3K R3113 11 GND
*D:D2~D5,D12,E3~E5,E7,E9,F4,F6, 3 COMP SW 6 (SWITCHING) 10K C3604 C3603 D3602
F7,F10,F11,G7~G10,H7~H13,J6, 10 1 MM5Z5V6B 12 GND
J8~J10,K5,K8~K10,K12,L5~L7, 4 FB GND 5 L3005 R3114 R3051
L10,L11,P2,T8 22uH 47K 100 13 GND
14 GND
R3012 C3056 C3074 C3053 R3603 D3007 15 AMP+13V
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
33K 10 10 OPEN OPEN OPEN C3995 16 AMP+13V
R3007 C3607 OPEN
12K OPEN 17 AMP+13V
C3062
C3008
C3006
C3004
C3055
C3048
18 AMP+13V
R3006
10K 19 GND
20 P-ON+21V
C3996 21 P-ON+21V
OPEN
22 P-ON+21V
DIGITAL MAIN CBA UNIT 23 P-ON+21V
S T U V W X
10-10 PL13.9ASCD4
Digital Main 5 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4
P-ON+3.3V
CHECK+1.8V
AL+3.3V
P-ON+5V
P-ON+3.3V(1) *1
IC3005(5/6)
AMP+13V R8A05011BG-U0
CONTINUE DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
4 DIGITAL 3
LED1
REMOTE
TO FUNCTION CBA R3552 R3558
Q3502
2SA1576UBTLQ
(LED DRIVE)
R3559
R3312 10K
D13 CHECK+1.8V NU G1
NU E1
UNIT CN4001 100 OPEN 10K
or CN4052 CN3101 NU G2
CONTINUE
SDA 1 R3560 R3210 R3402 DIGITAL 6
100K 100 0
SCL 2 HPD-SINK K14 HPD-SINK
GND 3 PWR J16 PWR
C3555 R3320 R3216 R3401
KEY-IN1 4 OPEN OPEN 100 0
REMOTE 5 C3559 R3551 R3555
OPEN 100 OPEN R3220
LED1 6 R3183 33K
R3318 22K
R3317 10K
R3319 10K
OPEN Q3010 R3219
LIGHT 7 OPEN 22
P-ON+5V 8 C3553 C3556 C3558 HP-DET K16
OPEN OPEN OPEN D3201
AL+3.3V 9 MM5Z5V6B
C3554 C3560 Q3501 R3185 CONTINUE
1 220 2SC4081UBTLQ OPEN R3191 DIGITAL 3
/6.3v (LED DRIVE) 100
C3329 0.01 RESET J15 CPU-RESET-N
C3551 33P R3184 R3186 D3111
C3552 33P R3553 D3501 OPEN OPEN A15 KEY-IN1 MM5Z5V6B
CONTINUE 100 MM5Z5V6B R3314 22
DIGITAL 4 B13 PROTECT3
R3315 OPEN
RESET A13 LIGHT-SENS
R3316 22 IC3009
PROTECT1 C13 PROTECT1 R3178 PST8429UR R3182
3 PROTECT3
C3231
C3328
OPEN
0.22
C12 LPF
TO DIGITAL TO DIGITAL
MAIN 2 MAIN 6
220 (RESET)
1 GND OUT 4
56K
1000P
1000P
R3556 R3557 IC3005(2/6) IC3005(6/6) C3116
OPEN
OPEN
OPEN
OPEN
CONTINUE 10 10 R3340 10K 2 VDD CD 3 1000P
DIGITAL 2 NU D11
C3219 10 D3108 C3106 C3113
SCL NU D7 OPEN 1 0.033
C3229
R3502
C3227
R3501
C3233
C3232
C3220 10
SDA NU C6
R3335 18K C3217 2.2 C3216 10
AUDIO(L)-IN A8 NU C5
R3336 18K C3218 2.2
AUDIO(R)-IN B8 AUDIO NU B6
C3223 1 I/F CONTINUE
R3995 R3862 B7 NU A6 R3209 DIGITAL 2
CONTINUE 10K 10K C3224 1 100
DIGITAL 3 A7 N10 SPDIF
HP-MUTE
AUDIO-MUTE R3865
10K
BACKLIGHT-SW
R3561 C3860 R3866 C3862
10 0.1 100K OPEN
R3867 R3868
0 OPEN
R3809 R3810 R3864
OPEN OPEN 1K R3851 C3851
15K 1 C3853
220/6.3V
R3861 R3853 JK3703
10K Q3861 OPEN C3856 R3856 HEADPHONE
C3825 C3824 2SC4081UBTLQ 1000P 10K JACK
2 R3814
OPEN
Q3803
R3870
220
R3813
OPEN
R3822
10
IC3801
TPA3110D2PWPR
(AUDIO AMP)
1 1000P (SWITCHING)
R3869
OPEN
4
GND
3 2 1
MUTE
IC3851
BH3547F
C3861
0.1
1 R3823
C3871
2200P
12
13 NU
14 PBTL
17
PVCCR 16
PVCCR 15
OPEN
C3806
OPEN L3804
10uH
1000P 1 OPEN 1
2
3
4
SP(L)+
SP(L)-
SP(R)-
SP(R)+
OPEN SP3802
C3831 C3826 C3829 R3804 C3814 C3823 D3804 SPEAKER
100/16V 100/16V 100/16V OPEN 1000P 1 OPEN R-CH
C3810
OPEN
Y Z AA BB CC DD
10-11 PL13.9ASCD5
Digital Main 6 Schematic Diagram [TYPE A, TYPE C]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4 HDMI-
P-ON+3.3V JK3002 CONNECTOR-2
C3316 C3421 C3423 C3425 C3426 1 TMDS-D2(+)
AL+3.3V 10 1 1 1 1 2 D-SHIELD0
P-ON+3.3V(1)
3 TMDS-D2(-)
P-ON+5V
D3993 C3420 C3422 C3424 C3427 4 TMDS-D1(+)
OPEN OPEN OPEN OPEN OPEN
5 D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER Q3014
RU1L002SNTL R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL 14 NU
MAIN 2 MAIN 5 R3415
IC3005(2/6) IC3005(5/6) 82K R3486 15 HDMI-CLOCK
3.9K 16 HDMI-DATA
D3057 IC3018 C3202 C3203 R3275 R3278 17 GND
VIDEO AUDIO RB751S-40 OPEN OPEN 47K 47K
DECODER DECODER 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TMDS351PAGR
R3237 (HDMI SW) 18 +5V
GND
VCC
GND
VCC
GND
NU
27K C3023 R3066 R3055 19 HOT PLUG DETECT
HDMI-CEC B15 0.1 2.7K 1K
17 HOT-PLUG- 64 Q3008
DETECT3 R3063 2SC4081UBTLQ
18 63 1K (SWITCHING)
C3989 C3988 R3489 R3058
B1 OPEN OPEN 10K 19 VCC 62 10K
A1
20 VCC 61 HDMI-
B2 JK3003 CONNECTOR-3
A2 21 60 1 TMDS-D2(+)
HDMI
I/F B3 C3987 C3986 2 D-SHIELD0
OPEN OPEN 22 GND 59
A3 3 TMDS-D2(-)
B4 23 GND 58 4 TMDS-D1(+)
A4 5 D-SHIELD1
3 C3985
OPEN
C3984
OPEN
24
25 VCC
26
HDMI SW 57
56
VCC 55
6
7
8
TMDS-D1(-)
TMDS-D0(+)
D-SHIELD2
C3990 9 TMDS-D0(-)
1P 27 54 10 TMDS-CLOCK(+)
R3488 R3487
4.7K 4.7K 11 C-SHIELD0
28 GND 53
12 TMDS-CLOCK(-)
SCL-SINK C16 29 SCL-SINK 52 13 HDMI-CEC
14 NU
SDA-SINK C15 30 SDA-SINK 51
R3514 15 HDMI-CLOCK
100
HPD-SINK F13 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2 16 HDMI-DATA
R3508 C3204 C3205 R3214 R3212
22 17 GND
HOT-PLUG-
HDMI-SEL0 G3 32 HDMI- NU 49 OPEN OPEN 47K 47K
SEL0
DETECT1
R3994 R3496 18 +5V
HDMI-
OPEN 4.7K C3005 R3019 R3010
SEL1
1K 19 HOT PLUG DETECT
VCC
GND
VCC
0.1 2.7K
NU
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Q3001
R3509 R3018 2SC4081UBTLQ
22 1K (SWITCHING)
HDMI-SEL1 F1
R3497 R3017
4.7K R3992 10K
R3990 0
OPEN HDMI-
R3236 C3185 R3270 C3187 JK3004 CONNECTOR-1
560 0.01 2.2K 2.2 R3991 1 TMDS-D2(+)
10K
EXT-RES C4 C3186 2 D-SHIELD0
2 PLL-XFC-A B5
PLL-XFC-P A5 R3271
3K
4700P
C3188
2200P
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
8 D-SHIELD2
9 TMDS-D0(-)
10 TMDS-CLOCK(+)
PWR M12 11 C-SHIELD0
R3193 12 TMDS-CLOCK(-)
4.7K
HDMI-SCL G14 13 HDMI-CEC
HDMI-SDA F14 D3003 D3001 C3208
RB751S-40 RB751S-40 OPEN 14 NU
R3192
4.7K 15 HDMI-CLOCK
16 HDMI-DATA
C3206 C3207 D3002 R3273 R3276 17 GND
CONTINUE OPEN OPEN RB751S-40 47K 47K
DIGITAL 5 18 +5V
HPD-SINK R3022 R3024 C3018 R3040 R3025 19 HOT PLUG DETECT
10K 10K 0.1 2.7K 1K
PWR
R3023
IC3011 22K Q3002
BU9883FV-WE2 2SC4081UBTLQ
(HDMI SERIAL EEPROM) R3029 (SWITCHING)
CONTINUE 1K
DIGITAL 2
VGA-SDA 1 VCC1 VCC2 16 R3027
10K
1 VGA-SCL
R3451
10K
R3453
1.5K
2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
R3073
0
R3074
0
C3192 0.1 R3075
R3281 5 VCC-OUT GND 12 0
Q3451 100
2SC4081UBTLQ 6 SDA0 SDA3 11 R3076 R3078
(SWITCHING) R3282 0 OPEN
R3452 100
10K 7 SCL0 SCL3 10 R3081 R3080
0 OPEN
8 VCC0 VCC3 9
DIGITAL MAIN CBA UNIT C3191
0.1
EE FF GG HH II JJ
10-12 PL13.9ASCD6
Digital Main 1 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
4 NU 10
GND 11
LVDS-OD0(-) 12
R3910
OPEN 27 VCOM
26 PWR-CTRL
25 P-ON+3.3V
LVDS-OD0(+) 13 24 GND
GND 14 23 LVDS-OD0(-)
LVDS-OD1(-) 15 22 LVDS-OD0(+)
LVDS-OD1(+) 16 21 LVDS-OD1(-)
GND 17 20 LVDS-OD1(+)
LVDS-OD2(-) 18 19 LVDS-OD2(-)
LVDS-OD2(+) 19 18 LVDS-OD2(+)
GND 20 17 GND
LVDS-OCLK(-) 21 16 LVDS-OCLK(-)
LVDS-OCLK(+) 22 15 LVDS-OCLK(+)
GND 23 14 GND
LVDS-OD3(-) 24 13 LVDS-OD3(-)
LVDS-OD3(+) 25 12 LVDS-OD3(+)
GND 26 R3908 11 LVDS-OD4(-)
OPEN R3932
BIST 27 18K 10 LVDS-OD4(+)
PANEL-SCL 28 R3907 9 LVDS-OD5(-)
OPEN
PANEL-SDA 29 R3934 8 LVDS-OD5(+)
3.9K
GND 30 7 GND
CONTINUE R3931 R3933 C3947 C3948 6 TP
DIGITAL 2 11K 12K 47/25V 0.1
LVDS-OD4(+) R3935 5 POL
1K
3 LVDS-OD4(-)
LVDS-OD3(+)
LVDS-OD3(-)
R3924
OPEN
Q3901
2SC4081UBTLQ
(VCOM DRIVE)
4 CPV
3 OE1
2 OE2
1 STV
LVDS-OCLK(+)
LVDS-OCLK(-)
LVDS-OD2(+)
LVDS-OD2(-)
CN3903 (NO CONNECTION)
LVDS-OD1(+) 31 LCD+21V
LVDS-OD1(-) 30 LCD+21V
LVDS-OD0(+) 29 LCD+21V
LVDS-OD0(-) 28 GND
LVDS-ED4(+) *1
IC3101(1/7) 27 VCOM
LVDS-ED4(-) MN2WS0270EA 26 PWR-CTRL
LVDS-ED3(+) DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER 25 P-ON+3.3V
LVDS-ED3(-) R3916 24 GND
R3913 0x4 10K
LVDS-ECLK(+) L3 23 LVDS-OD0(-)
LVDS-ECLK(-) L4 22 LVDS-OD0(+)
LVDS-ED2(+) J6 K3 21 LVDS-OD1(-)
LVDS-ED2(-) K6 K4 20 LVDS-OD1(+)
LVDS-ED1(+) J5 19 LVDS-OD2(-)
LVDS-ED1(-) R3914 0x4
K5 J1 18 LVDS-OD2(+)
LVDS-ED0(+) L7 J2 17 GND
LVDS-ED0(-) LVDS
M7 TX J3 16 LVDS-OCLK(-)
H3
R3915 0x4
15
14
13
LVDS-OCLK(+)
GND
LVDS-OD3(-)
LCD+12V 28 N5 H4 12 LVDS-OD3(+)
LCD+12V 27 M5 G3 11 LVDS-OD4(-)
GND 26 M6 F3 10 LVDS-OD4(+)
GND 25 F1 9 LVDS-OD5(-)
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
GND 24 K7 NU F2 8 LVDS-OD5(+)
PANEL-WP 23 J7 NU NU P1 7 GND
R3974 100
C3916
C3903
C3904
C3905
C3908
C3911
C3906
C3907
C3912
C3913
C3914
C3915
LVDS-SEL 22 TP R6 6 TP
R3975 100
NU 21 TO DIGITAL POL R3 5 POL
MAIN 6 R3976 100
GND 20 IC3101(5/7) CPV P3 4 CPV
R3977 100
LVDS-OD0(-) 19 OE N3 3 OE
R3978 100
LVDS-OD0(+) 18 OE2 R5 2 OE2
R3979 100
GND 17 STV P4 1 STV
OPEN
OPEN
100K
100K
100K
100K
100K
100K
OPEN
OPEN
OPEN
OPEN
OPEN
100P
LVDS-OD1(-) 16
3P
3P
3P
3P
3P
3P
3P
3P
3P
3P
LVDS-OD1(+) 15 CONTINUE
DIGITAL 4
R3884
R3928
R3883
R3882
R3881
R3880
C3928
C3917
C3918
C3919
C3922
C3923
C3920
C3921
C3924
C3925
C3926
C3927
C3942
C3998
C3941
C3940
C3939
C3938
GND 14
LVDS-OD2(-) 13 VCOM-PWM
LVDS-OD2(+) 12
GND 11 N2 NU CONTINUE
P2 NU DIGITAL 2
LVDS-OCLK(-) 10 VCOM-DC
1 LVDS-OCLK(+) 9
GND 8
LVDS-OD3(-) 7
R3901
10K
P7 BACKLIGHT-ADJ
VCOM-PWM
LCD-P-ON
PANEL-WP
LVDS-OD3(+) 6 PANEL-SCL
GND 5 PANEL-SDA
NU 4
R3906 OPEN
PANEL-SCL 3 CN3902 (NO CONNECTION)
R3904 OPEN
PANEL-SDA 2 1 GND
GND 1 2 PANEL-WP
R3925 3 PANEL-SCL
CONTINUE OPEN
DIGITAL 7
BACKLIGHT-ADJ DIGITAL MAIN CBA UNIT 4 PANEL-SDA
A B C D E F
10-13 PL13.9BSCD1
Digital Main 2 Schematic Diagram [TYPE B, TYPE E, TYPE F]
CONTINUE
DIGITAL 7
P-ON+21V
P-ON+3.3V R3942
OPEN
CONTINUE
DIGITAL 2 R3952 D3905 Q3905
OPEN OPEN
4 LCD+12V/+21V
D3906
OPEN
R3550
IC3901
MP1472GJC452Z
C3996
OPEN
R3899
1
2
OPEN
8
7
6.8K (+12V REG.) OPEN
C3946 3 6
0.047
1 SS BST 8 R3897 4 5
C3949 OPEN
0.1
2 EN IN 7 R3891
R3990 C3951 C3945 C3944 C3943 OPEN
(NO CONNECTION) CN3906 OPEN OPEN 0.1 OPEN 4.7
LCD+12V 1 3 COMP SW 6 R3895
OPEN Q3904
LCD+12V 2 C3992 C3991 4 FB GND 5 OPEN
OPEN OPEN R3898 C3997
LCD+12V 3 C3950 R3938 OPEN OPEN
1500P 33K
LCD+12V 4 C3955 R3937
100P R3936 3.3K R3939 L3901
NU 5 24K 6.8K 22uH
GND 6 CONTINUE
DIGITAL 6
GND 7 R3912 R3911 C3959 C3958 C3952 D3901 C3954 C3956 C3953 P-ON-H2
GND 8 OPEN OPEN OPEN 4.7 OPEN OPEN 4.7 4.7 4.7
R3989 OPEN
GND 9
R3988 OPEN
GND 10
R3981 OPEN
LVDS-OD4(+) 11
R3980 OPEN
LVDS-OD4(-) 12
R3943 OPEN
3 LVDS-OD3(+) 13
LVDS-OD3(-) 14
GND 15
R3921 OPEN
CONTINUE
LVDS-OCLK(+) 16 DIGITAL 1
R3920 OPEN
LVDS-OCLK(-) 17 LVDS-OD4(+)
GND 18 LVDS-OD4(-)
LVDS-OD2(+) 19 LVDS-OD3(+)
LVDS-OD2(-) 20 LVDS-OD3(-)
R3919 OPEN
LVDS-OD1(+) 21 LVDS-OCLK(+)
LVDS-OD1(-) 22 LVDS-OCLK(-)
LVDS-OD0(+) 23 LVDS-OD2(+)
LVDS-OD0(-) 24 LVDS-OD2(-)
R3987 OPEN
GND 25 LVDS-OD1(+)
R3986 OPEN
GND 26 LVDS-OD1(-)
R3985 OPEN
LVDS-ED4(+) 27 LVDS-OD0(+)
R3984 OPEN
LVDS-ED4(-) 28 LVDS-OD0(-)
LVDS-ED3(+) 29 LVDS-ED4(+)
LVDS-ED3(-) 30 LVDS-ED4(-)
GND 31 LVDS-ED3(+)
LVDS-ECLK(+) 32 LVDS-ED3(-)
2 LVDS-ECLK(-) 33
GND 34
LVDS-ED2(+) 35
LVDS-ECLK(+)
LVDS-ECLK(-)
LVDS-ED2(+)
LVDS-ED2(-) 36 LVDS-ED2(-)
LVDS-ED1(+) 37 LVDS-ED1(+)
LVDS-ED1(-) 38 LVDS-ED1(-)
LVDS-ED0(+) 39 LVDS-ED0(+)
LVDS-ED0(-) 40 LVDS-ED0(-)
GND 41
R3866 OPEN
NU 42
R3867 OPEN CONTINUE
NU 43 DIGITAL 1
R3922 OPEN C3902 R3896 R3900 OPEN
NU 44 OPEN OPEN VCOM-DC
R3903 OPEN
VCOM 45 VCOM-PWM
R3905 OPEN
LCD-P-ON 46 LCD-P-ON
R3869 OPEN R3941 R3940 C3909 C3910
NU 47 OPEN OPEN OPEN OPEN PANEL-WP
R3926 OPEN
NU 48 PANEL-SCL
R3923 OPEN
PANEL-SDA 49 D3902 PANEL-SDA
R3902 OPEN 1SS400
PANEL-SCL 50
PANEL-WP 51 C3901
R3982 OPEN 4.7
CONTINUE
1 R3983 OPEN
R3918 OPEN
R3917 OPEN
DIGITAL 8
PROTECT3
G H I J K L
10-14 PL13.9BSCD2
Digital Main 3 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
*1
IC3101(2/7)
MN2WS0270EA
MAIN MICRO CONTROLLER
/DIGITAL SIGNAL PROCESS DIGITAL MAIN CBA UNIT CONTINUE
R3433 10K DIGITAL 7
DDRPWRON T5 AL+3.3V
R3421 270
MMVREF0 D3 VCC+1.5V
R3423 270
MMVREF1 D16
R3411 270 IC3401 IC3402
MMVREF2 D6
K4B1G1646G-BCH9 K4B1G1646G-BCH9
MMDQ0 (DDR3 SDRAM) (DDR3 SDRAM)
MMDQ0 D7
0.1
270
0.1
270
0.1
270
MMDQ1 E6 MMDQ1
C3409
R3422
C3410
R3424
C3406
R3410
MMDQ3 T7 A14 VDD2 D9 10 10 T7 A14 VDD2 D9 10 10
MMDQ3 C5 MMA13 T3 A13 VDD3 G7 MMA13 T3 A13 VDD3 G7
MMDQ4 C3 MMDQ4 MMA12 MMA12
MMDQ5 N7 A12/BC# VDD4 K2 N7 A12/BC# VDD4 K2
MMDQ5 B1 MMA11 R7 A11 VDD5 K8 C3408 C3412 C3413 C3414 MMA11 R7 A11 VDD5 K8 C3421 C3422 C3423 C3424
MMDQ6 C2 MMDQ6 MMA10 1 0.1 0.1 0.1 MMA10 0.1 0.1 0.1 0.1
MMDQ7 L7 A10/AP VDD6 N1 L7 A10/AP VDD6 N1
MMDQ7 C1 MMA9 R3 A9 VDD7 N9 MMA9 R3 A9 VDD7 N9
MMDQ8 C8 MMDQ8 MMA8 MMA8
T8 A8 VDD8 R1 C3415 C3416 C3417 C3418 T8 A8 VDD8 R1 C3425 C3426 C3427
MMDQ9 D8 MMDQ9 MMA7 0.1 0.1 0.1 0.1 MMA7 0.1 0.1 0.1
MMDQ10 R2 A7 VDD9 R9 R2 A7 VDD9 R9
MMDQ10 C7 MMA6 R8 A6 VDDQ1 A1 MMA6 R8 A6 VDDQ1 A1
MMDQ11 B7 MMDQ11 MMA5 MMA5
MMDQ12 P2 A5 VDDQ2 A8 P2 A5 VDDQ2 A8
MMDQ12 C4 MMA4 P8 A4 VDDQ3 C1 MMA4 P8 A4 VDDQ3 C1
MMDQ13 A3 MMDQ13 MMA3 MMA3
MMDQ14 N2 A3 VDDQ4 C9 N2 A3 VDDQ4 C9
MMDQ14 B3 MMA2 P3 A2 VDDQ5 D2 MMA2 P3 A2 VDDQ5 D2
MMDQ15 A2 MMDQ15 MMA1 MMA1
MMDQ16 P7 A1 VDDQ6 E9 P7 A1 VDDQ6 E9
MMDQ16 D19 MMA0 N3 A0 VDDQ7 F1 MMA0 N3 A0 VDDQ7 F1
MMDQ17 C18 MMDQ17
MMDQ18 VDDQ8 H2 VDDQ8 H2
MMDQ18 B18 VDDQ9 H9 VDDQ9 H9
MMDQ19 C17 MMDQ19
MMDQ20 C7 DQSU C7 DQSU
MMDQ20 B14 B7 DQSU# R3425 B7 DQSU# R3429
MMDQ21 A14 MMDQ21 270 270
MMDQ22 F3 DQSL VREFCA M8 F3 DQSL VREFCA M8
MMDQ22 C13 G3 DQSL# G3 DQSL#
MMDQ23 R3426 C3419 C3429 R3430 C3428 C3430
MMDQ23 B13 D3 DMU 270 0.1 0.1 D3 DMU 270 0.1 0.1
MMDQ24 B17 MMDQ24 VREFDQ H1 VREFDQ H1
E7 DML E7 DML
3 MMDQ25
MMDQ26
MMDQ27
A17
D15
C15
MMDQ25
MMDQ26
MMDQ27
MMDQ28
MMDQ11
MMDQ14
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ19
MMDQ22
A3
B8
DQU7
DQU6
VSS1
VSS2
A9
B3
MMDQ28 B12 MMDQ10 MMDQ18
MMDQ29 A12 MMDQ29 A2 DQU5 VSS3 E1 A2 DQU5 VSS3 E1
MMDQ30 MMDQ12 A7 DQU4 VSS4 G8 MMDQ20 A7 DQU4 VSS4 G8
MMDQ30 D11 MMDQ8 MMDQ16
MMDQ31 C11 MMDQ31 C2 DQU3 VSS5 J2 C2 DQU3 VSS5 J2
MMDQ15 C8 DQU2 VSS6 J8 MMDQ23 C8 DQU2 VSS6 J8
MMDQS1 B4 MMDQ9 C3 DQU1 VSS7 M1 MMDQ17 C3 DQU1 VSS7 M1
MMXDQS1 A4 MMDQ13 D7 DQU0 VSS8 M9 MMDQ21 D7 DQU0 VSS8 M9
MMDQS0 A6 MMDQ6 H7 DQL7 VSS9 P1 MMDQ30 H7 DQL7 VSS9 P1
MMXDQS0 C6 MMDQ2 G2 DQL6 VSS10 P9 MMDQ26 G2 DQL6 VSS10 P9
MMDQS3 D17 MMDQ7 H8 DQL5 VSS11 T1 MMDQ31 H8 DQL5 VSS11 T1
MMXDQS3 C16 MMDQ3 H3 DQL4 VSS12 T9 MMDQ27 H3 DQL4 VSS12 T9
MMDQS2 B15 MMDQ4 F8 DQL3 VSSQ1 B1 MMDQ28 F8 DQL3 VSSQ1 B1
MMXDQS2 C14 MMDQ1 F2 DQL2 VSSQ2 B9 MMDQ25 F2 DQL2 VSSQ2 B9
MMDQ5 F7 DQL1 VSSQ3 D1 MMDQ29 F7 DQL1 VSSQ3 D1
MMDM1 C9 MMDQ0 MMDQ24
MMDM0 B2 E3 DQL0 VSSQ4 D8 E3 DQL0 VSSQ4 D8
MMDM3 C12 VSSQ5 E2 VSSQ5 E2
MMDM2 C19 VSSQ6 E8 VSSQ6 E8
L2 CS# VSSQ7 F9 L2 CS# VSSQ7 F9
R3405 56x4 MMA2 K3 CAS# K3 CAS#
MMA2 G11 VSSQ8 G1 R3403 C3403 VSSQ8 G1 R3401 C3401
MMA6 K1 ODT OPEN OPEN K1 ODT OPEN OPEN
MMA6 E8 VSSQ9 G9 VSSQ9 G9
MMA8 G8 MMA8 J3 RAS# R3427 J3 RAS# R3431
2 MMA14
MMA9
MMA11
E7
E19
F18
R3406 56x4
MMA14
MMA9
MMA11
R3428
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3404
OPEN
C3404
OPEN
R3432
L3
T2
L8
WE#
RESET#
ZQ
CK J7
CK# K7
CKE K9
220
R3402
OPEN
C3402
OPEN
R3409 56x4
MMBA2 G16
MMBA0 E15
MMXWE D14
MMXCAS E14
MMCK B10
MMXCK B9
R3418 56
MMXCS1 D12
R3417 56
MMXCS0 E11
R3416 56
MMODT0 F11
1 MEMORY
I/F MMODT1
MMCKE0
MMCKE1
F12
F10
G10
R3415
R3414
R3413
R3412
56
56
56
56
MMXRAS F14
MMXRESET F19
TO DIGITAL C3405 1
MAIN 6 DDR3VOUT D1 R3419 C3407
IC3101(5/7) R3420 240 10K OPEN
MMZQ D4
NU G7
NU G12
M N O P Q R
10-15 PL13.9BSCD3
Digital Main 4 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
*1
IC3101(3/7)
MN2WS0270EA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER C3125 C3126
0.1 0.1
4 CONTINUE
C3128
15P
C3124
X3101
25MHz
R3170
R3169
OPEN
AE4 AXI
10K
10K
10K
10K
COMP-DET H6 COMP-DET MMCDAT5 E20
MMCDAT6 4 NU NU 45 R3192
HP-DET G4 NU MMCDAT6 B20 56x4
R3132
R3121
R3124
R3173
R3111 R3112 M3 NU MMCDAT7 C20 MMCDAT7 5 NU I/O7 44 MMCDAT7
10K 100
L2 HP-DET MMCDAT6
6 NU I/O6 43
D20 NU
R3205 22 MMCDAT5
A20 NU NANDRYBY D22 7 R/B I/O5 42
R3201 75
W20 NU NFALE B23 MMCDAT4
R3202 75 8 RE I/O4 41
V20 NU NFCLE C23
R3203 75
Y22 NU TO DIGITAL XNFCE A23 9 CE NU 40
MAIN 6 R3190 75
CONTINUE AA22 NU IC3104(5/7) XNFWE A24
DIGITAL 7 R3189 75 10 NU NU 39
AB23 NU XNFWP B24
P-ON+3.3V R3208 R3204 75
OPEN W21 NU XNFRE E21 11 NU NU 38
P-ON+5V U20 NU NU C22
3 12 VCC VCC 37
R3128 10K
R3123 10K
AL+3.3V V21 NU NU F20
R3135
OPEN Y21 NU NU J24 13 VSS VSS 36
U19 NU NU J22
14 NU NU 35
W19 NU NU G24
V19 NU NU G23 15 NU NU 34
AB22 NU NU H23
(NO CONNECTION) CN3104 16 CLE NU 33 R3191
GND 10 U21 NU NU G22 56x4
NU H22 17 ALE I/O3 32 MMCDAT3
NU 9
EJTCK 8 AA7 NU NU K22 MMCDAT2
18 WE I/O2 31
JTDI 7 U9 NU NU J25
NU P22 19 WP I/O1 30 MMCDAT1
JTDO 6 AD8 NU
JTMS 5 AB7 NU NU P25 MMCDAT0
20 NU I/O0 29
TRSTN 4 Y8 NU NU R20
R3127 OPEN NU T21 21 NU NU 28
EVTRG 3 L21 NU
XRST 2 AC5 NU NU R22
22 NU NU 27
AL+3.3V 1 R3136 R3113 R3129
100 R3210 NU R21
10K 10K R3198 10K OPEN NU T20 23 NU NU 26
R3125 OPEN E24 NU NU T19
24 NU NU 25
G21 NU NU R19
CONTINUE
DIGITAL 8 R3130 E23 NU NU P24
2 STB-RESET
STMTIME1
OPEN
R3126
OPEN
D25
C25
D24
NU
NU
NU
NU
NU
NU
P21
AB18
Y18
J19 NU NU Y17
H19 NU NU W17
L20 NU NU W15
J23 NU NU AA17
L19 NU NU W18
N20 NU NU AC19
K19 NU NU Y16
N21 NU NU AD19
M20 NU NU W16
M19 NU NU Y20
J20 NU NU AB19
P20 NU NU AE20
K21 NU NU AB20
N19 NU NU AA18
R3224 1K
P19 NU NU AD20
R3115 OPEN
M21 NU NU AA21
F25 NU NU Y19
1 R3116 OPEN
R3118 1K
R3122 OPEN
H20
F23
F24
NU
NU
NU
NU
NU
NU
AA19
AA20
AC20
F22 NU
H21 NU
K20 NU
S T U V W X
10-16 PL13.9BSCD4
Digital Main 5 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 7
P-ON+5V TU3001
TUNER UNIT
P-ON+3.3V
DIF-OUT1
DIF-OUT2
IF-AGC
+3.3V
*1
GND
SDA
SCL
IC3101(4/7)
MN2WS0270EA 1 2 3 4 5 6 7
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
CONTINUE M1 NU L3005
DIGITAL 8 2.2uH
UART1TX N4 NU
M2 NU C3041 C3040 C3039 D3007
UART1RX NU AB9 OPEN 10 OPEN MM5Z5V6B
P5 NU NU AC9
R3193 100
F21 UART1RX NU Y12
R3194 100
G20 UART1TX NU AA15 C3002 D3001
R3217 1K OPEN OPEN
(NO CONNECTION) CN3101 B25 NU NU W14
GND 4 D23 NU NU W10
R3176 100
UARTORX 3 C24 UART0TX NU Y13
R3175 100 C3003 D3002
UARTOTX 2 E22 UARTOTX NU W8 OPEN OPEN
P-ON+5V 1 NU AA8
C3115 C3116 R3101 C3117 R3108 C3011 L3003 R3005
OPEN OPEN 10K OPEN OPEN 0.1 3.3uH 270
AD9
3 (USB JACK)
USB+5V
USB0(-)
CN3704
1
2
L3706
OPEN
N22 USB0(-)
DEMODULATOR
/MPEG
DECODER
AE9
C3026
OPEN C3014
C3027
0.1
C3013
39P L3004
3.3uH
R3003
270
2 USB1(-)
USB1(+)
GND
3
2
1
R3735
M22 USB1(-)
L23 USB1(+)
NU U10
RX(-) AC8
R7
R6
R5
NU
RX(-)
RCT
OPEN RX(+) AC7 R4 RX(+)
R3734 R3736 TX(-) AE6 R3 TX(-)
0 0 R3180 10K
WIRELESS M23 USB10D R2 TCT
LAN MODULE CN3701
USB1(+) 1 TX(+) AD6 R1 TX(+)
IC3702 C3744 C3701
USB1(-) 2 OPEN 0.01 0.01
USB+5V 3 1 VOUT VIN 5
GND 4 C3716 C3715
OPEN 2 GND OPEN
GND 5
GND 6 3 /FLAG EN 4 M25 USB1VBUS
R3704 C3714
OPEN OPEN CONTINUE
DIGITAL 7
R3702 CTRL11 AC6 CTRL11
OPEN
C3129
1
1
DIGITAL MAIN CBA UNIT
Y Z AA AB AC AD
10-17 PL13.9BSCD5
Digital Main 6 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
*1
DIGITAL MAIN CBA UNIT IC3101(5/7)
MN2WS0270EA
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3701
COMPONENT-Y AE12 NU
/VIDEO-IN C3705 D3705 R3166 AC12 NU
39P OPEN 75
AD12 NU A/D
Y9 NU CONVERTER
COMPONENT
-Pb-IN C3770 D3701 R3163 Y10 NU
39P OPEN 75
AA9 NU
4 CONTINUE
DIGITAL 4
COMPONENT
-Pr-IN C3703
39P
D3704
OPEN
R3164
75
C3121
C3118
C3119
1
1
1
R3214
R3216
R3218
10
10
10
AC10 NU
AB10
AD11 TO DIGITAL
C3706 AB11 MAIN 3
COMP-DET 0.01 R3727 R3723 C3120 1 R3219 10 SW IC3101(2/7)
R3741 10K C3704 AC11
HP-DET C3720 100 1
33 100P C3109 1 R3220 100
Q3709 AD13
C3709 R3725 2SC4081UBTLQ R3724 C3113 1 R3221 100 TO DIGITAL
JK3706 1 220 10K AB13 MAIN 4
DIGITAL (BUFFER) C3114 1 R3222 100 IC3101(3/7)
AUDIO OUT AC13 DIGITAL
(COAXIAL) C3708 D3702 R3726 C3707 SIGNAL
100P OPEN 110 33P R3171 R3168 R3167 PROCESS
75 75 75 TO DIGITAL
MAIN 8
AUDIO(L)-IN R3155 100 IC3101(7/7)
C3710 R3708 D3703 Y11 VGA-HSYNC
56P 10K OPEN R3154 100
AA12 VGA-VSYNC
TO DIGITAL
MAIN 5
AUDIO(R)-IN C3711 R3709 D3707 R3147 36 C3103 1 IC3101(4/7)
56P 10K OPEN W11
R3148 36 C3104 1
AA11
JK3713 R3149 36 C3105 1
AB12
PC-RGB-IN R3145 36 C3102 1
AA10 TO DIGITAL
MAIN 1
IC3101(1/7)
1 6 11 E4 NU
R3195 10K
D2 NU
2 7 12 R3196 10K
F6 NU
R3197 10K
3 3
4
8
9
13
14
R3199 OPEN
G5
E3
SPDIF
NU
NU
F4
C3207 1 R3297 100K
5 10 15 AE14
C3208 1 R3298 100K
D3711 1SS400
AC14
OPEN
OPEN
OPEN
OPEN
OPEN
R3839 47K
R3838 47K
R3831 10K
R3830 10K AB14 NU
AC15 NU TO DIGITAL
MAIN 8
D3717
D3716
D3715
D3714
D3713
AC16 NU IC3101(7/7)
AD16 NU AUDIO
I/F
CONTINUE AB16 NU
DIGITAL 7 D3712
1SS400 AE17 NU
P-ON+5V TO DIGITAL
AD17 MAIN 5
P-ON+3.3V AC17 IC3101(4/7)
AMP+13V AB17
AC18
CONTINUE
DIGITAL 8 E2 AUDIO-MUTE
VGA-SCL F5 ARC-OUT
VGA-SDA CONTINUE
DIGITAL 8
CONTINUE ARC-OUT
DIGITAL 2
P-ON-H2
R3733 R3751
2 R3809
10K
R3810
OPEN
R3728 C3713
3.3 220/6.3V
4.7K 47K
JK3801
HEADPHONE
R3729 R3737 R3746 R3738 C3712 R3743 JACK
3.3 10K 10K 10K 220/6.3V 10K
C3825 C3824 C3842
R3811 R3826 2.2 0.047 10 R3731 R3740 R3752
1K OPEN OPEN OPEN OPEN
IC3803 Q3708
R3820 R3813 TPA3110D2PWPR OPEN
560 10 (AUDIO AMP) R3739 R3744
Q3821 OPEN OPEN Q3701
2SA1576UBTLQ OPEN
(SWITCHING) 1 PVCCL 28 R3732
C3830 R3812 CONTROL OPEN
OPEN 100K LOGIC Q3710
2 PVCCL 27 OPEN
R3713 C3718
R3822 C3805 1 C3801 0.22 OPEN OPEN
10K 3 26
CONTINUE POWER PWM DRIVE L3801
DIGITAL 7 R3832 C3818 1 LIMIT LOGIC 10uH
R3823 22K 4 25
HP-MUTE 1.8K R3805 OPEN R3801 C3811 C3820 C3834 C3838 D3801
AUDIO-MUTE R3824 5 GND 24 OPEN 1000P 1 OPEN OPEN OPEN
10K Q3822 GAIN C3807
LCD-P-ON 2SC4081UBTLQ R3806 0 CONTROL OPEN L3802
(SWITCHING) 6 23
R3825 DRIVE 10uH
CONTINUE 47K C3802 0.22
DIGITAL 8 R3828 7 AVCC 22
OPEN R3802 C3812 C3821 C3835 C3839 D3802
SP-MUTE C3815 R3807 OPEN C3803 0.22 OPEN 1000P 1 OPEN OPEN OPEN
1 8 GND 21 C3808
C3816 1 DRIVE OPEN L3803
9 GVDD 20 10uH SP3801
R3808 CN3801 SPEAKER
C3817 1 10K
1 R3814
OPEN
R3817
OPEN
R3821
560
C3819 1
C3806 1
10
11
POWER
LIMIT
PWM
LOGIC DRIVE
GND 19
18
C3827
0.047
C3804 0.22
C3828
2.2
R3803
OPEN
C3809
OPEN L3804
10uH
C3813
1000P
C3822
1
C3836
OPEN
C3840 D3803
OPEN OPEN 1
2
3
SP(L)+
SP(L)-
SP(R)-
L-CH
12 17 4 SP(R)+ SP3802
R3815 R3818 R3833 R3804 C3814 C3823 C3837 C3841 D3804 SPEAKER
OPEN OPEN 22K 13 NU PVCCR 16 OPEN 1000P 1 OPEN OPEN OPEN R-CH
C3810
R3816 R3819 14 PBTL PVCCR 15 OPEN
OPEN OPEN C3831 C3826 C3829 C3843
100/16V 220/16V 220/16V 10
AE AF AG AH AI AJ
10-18 PL13.9BSCD6
Digital Main 7 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 1
P-ON+21V
P-ON+3.3V
CONTINUE
DIGITAL 2 C3182
P-ON+21V C3630 2700P
OPEN
P-ON+3.3V R3630
0 *1
IC3604 R3626 IC3101(6/7)
CONTINUE RT8293ALZSP 0 MN2WS0270EA
DIGITAL 6 R3609
4 HP-MUTE
AUDIO-MUTE
LCD-P-ON R3610
OPEN
R3611
OPEN
10K
C3639
0.01
(+1.14V REG.)
1 BS
2 VIN
SS 8
EN 7
C3601
0.015
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
AFB R4
R3223
0
Q3601 C3183
OPEN C3645 C3655 C3656 C3654 OPEN
R3612 4.7 0.1 0.1 OPEN 3 SW COMP 6
CONTINUE OPEN C3638 R3181 C3134
DIGITAL 8 4 GND FB 5 0.015 0 1
STB-RESET R3676 AVDDVAD11 U12
OPEN R3613 R3625
LCD-P-ON OPEN 2.2K LVVDD11 K11
R3624 VDD11 *A C3132 C3136 C3142 C3138
BACKLIGHT-SW L3601 OPEN L3102 1 10 10 1
10uH 0
PROTECT3 AVDDH11 AC21
PROTECT1 R3689 C3646 C3641 C3643 C3642 C3644 C3139 C3143 C3144 C3130 C3131
OPEN OPEN 10 10 OPEN OPEN AVDDH11 AD21 1 1 1 0.1 0.1
P-ON-H2 C3133
HP-MUTE C3969 OPEN CONTINUE
OPEN DIGITAL 5
AVDD11-CEN T9 CTRL11
R3607 IC3601 AVDD11-RX AB4 C3147 C3148 C3149
56K C3605 0.1 0.1 0.1
R3601 PST8429UR 1000P DVDD11 T10
CONTINUE OPEN (RESET) C3616 C3615 C3609
DIGITAL 1 R3602 4.7 0.1 OPEN VDD33-1 N12
BACKLIGHT-ADJ 220 1 GND OUT 4 IC3603 VDD33-2 N13 C3178 C3179 C3156 C3157 C3158
MP1472GJC452Z 1 1 10 0.1 0.1
D3601 2 VDD CD 3 (+3.3V REG.) DPAVDD33 M12
TO POWER SUPPLY OPEN D3603 C3606 C3607
3 CBA CN501
NU
PROTECT1
PROTECT3
CN3601
1
2
3
R3620 100
R3603 100
OPEN
R3608
270
C3602
1 0.01
C3604
0.033
R3606 C3611
11K 3300P
1 SS
2 EN
BST 8
VIN 7 C3612
0.01
AVDDH33
VDDEM18-33
LVVDD33-1
LVVDD33-2
AB21
M13
L11
M11 C3155
L3101
BEAD
2 P-ON+21V
P-ON+21V
P-ON+21V
P-ON+21V
20
21
22
23
C3676
OPEN
D3605
MM5Z15B
Q3602
R3622
10K
C3665 R3627
OPEN 100K
R3635 C3666
5.1K 4700P
2 EN
3 COMB
4 FB
VIN 7
SW 6
GND 5
0.01 VDDSD18-33 J21
AVDD33-CEN P10
C3169
0.1 L3106
BEAD
R3615 2SA1576UBTLQ D3609 C3613
10K (SW+12V) OPEN OPEN R3633 R3679 AVDD33-TX P9 C3170 C3171 C3177
10K 6.2K 0.1 0.1 10 R3184
CONTINUE 0
DIGITAL 6 D3608 R3095 R3634 L3603 VDDTCON25-33 M9
R3618 1SS400 10K 100 10uH
P-ON+5V 4.7K C3168
0.1 CONTINUE
P-ON+3.3V R3619 C3668 C3672 C3670 C3671 C3669 R3685 DIGITAL 3
Q3603 10K 470/4V 10 10 10 OPEN OPEN
AMP+13V 2SC4081UBTLQ STMADAVDD33 M10 AL+3.3V
(SWITCHING) R3621 C3610 C3968 C3174 C3173 C3172
OPEN 1 OPEN STMRONA T4 0.1 10 1 VCC+1.5V
CONTINUE VDDSTM33 L10
DIGITAL 4
P-ON+3.3V VDDIO15 *B
P-ON+5V C3625 C3632 C3631 C3153 C3152 C3141 C3145 C3146 C3150
4.7 0.1 OPEN 10 1 1 1 1 1
AL+3.3V IC3607
MP1472GJC452Z
(+5V REG.) C3137 C3140 C3151 C3184 C3185
CONTINUE R3631 C3617 1 1 1 1 1 L3108
DIGITAL 5 0 0.1 BEAD
P-ON+5V 1 SS BST 8 VDDIOCK15 D5
P-ON+3.3V 2 EN VIN 7 C3620 VDDSTM11 N10 C3154
R3614 C3619 0.01 0.1
R3623 C3618 4.3K 4700P FPEN N9 C3175
22K OPEN 3 COMB SW 6 1
1 CONTINUE
DIGITAL 8
P-ON+5V
P-ON+3.3V
D3606
1SS400 R3617
10K
R3678
12K
4 FB GND 5
TESTSEL
NU
GND
R12
*C
*D
*A:J11~J17,K12~K17,L14~L17,M15~M17
*B:E9,F8,F9,G13~G15,G19
R3616 *C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25,
AL+3.3V 33K L3605 R3022 0 V5,AD1,AD2,AE2
22uH
R3023 0 *D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15,
D3615 C3628 C3621 C3623 R3696 HEAT SINK G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14,
KDZTR6.8B 10 10 OPEN OPEN R3024 0 N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11,
T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14,
AA14,AC4,AE1,AE25
DIGITAL MAIN CBA UNIT C3966
OPEN
AK AL AM AN AO AP
10-19 PL13.9BSCD7
Digital Main 8 Schematic Diagram [TYPE B, TYPE E, TYPE F]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3101.
IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
4 R3188
OPEN R3209
OPEN
R3200
OPEN R3109 10K
DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
JK3717
HDMI-
CONNECTOR-1
R3206 AA4 NU AD24 1 DATA2(+)
OPEN Q3108 Y1 NU
OPEN AE24 2 TMDS DATA2 SHIELD
R3215 AB1 NU AD23 3 DATA2(-)
R3207 OPEN AB3 NU
OPEN AE23 4 DATA1(+)
(NO CONNECTION) CN3103 AB2 NU
AL+3.3V 1 AC23 5 TMDS DATA1 SHIELD
Y4 NU AE22 6 DATA1(-)
P-ON-H2 2 V6 NU
R3131 AD22 7 DATA0(+)
1K R3212 AA3 NU
100K AC22 8 TMDS DATA0 SHIELD
V4 NU Y23 9 DATA0(-)
CONTINUE AA24 10 CLOCK(+)
DIGITAL 2 R3120 AA23 11 TMDS CLOCK SHIELD
PROTECT3 OPEN
W4 LED2 HDMI AB25 12 CLOCK(-)
C3100 Q3103 R3143 I/F
CONTINUE 220/6.3V OPEN OPEN AB24 13 HDMI-CEC
DIGITAL 7 AC25 14 ARC
P-ON+5V AC24 15 HDMI-CLOCK
P-ON+3.3V AD25 16 HDMI-DATA
AL+3.3V U23 R3721 R3718 R3706 17 GND
R3096 10K 47K 47K
TO FUNCTION CBA 22K V24 18 +5V
UNIT CN4001 or C3702 R3722 R3703 R3705
CN4052 CN3105 Y5 SW-EN V23 0.1 47K 10K 1K 19 HOT PLUG DETECT
SDA 1 U3 REMOTE V22
3 SCL 2
GND 3
KEY-IN1 4
R3117
10
R3107
100
C3107
R3146
100K
V3 LED1 W23
W22
Y25
R3701
10K Q3707
2SC4081UBTLQ
(SWITCHING)
R3719
OPEN
JK3716
1
HDMI-
CONNECTOR-3
DATA2(+)
REMOTE 5 OPEN R3102 Y24
1K 2 TMDS DATA2 SHIELD
LED1 6 R3323
OPEN Q3102 3 DATA2(-)
LIGHT 7 OPEN
P-ON+5V 8 C3110 C3112 R3119 C3108 4 DATA1(+)
OPEN OPEN OPEN OPEN
C3111 AUDIO VIDEO 5 TMDS DATA1 SHIELD
AL+3.3V 9 0.1 DECODER DECODER
C3101 6 DATA1(-)
0.1 Q3101 R3106 R3159 7 DATA0(+)
C3122 OPEN 2SC4081UBTLQ OPEN OPEN
(LED DRIVE) T3 LIGHT-SENS 8 TMDS DATA0 SHIELD
CONTINUE C3123 OPEN R3103 R3104 C3106 R3182 TO DIGITAL TO DIGITAL
DIGITAL 4 OPEN OPEN OPEN 10K MAIN 6 MAIN 6 9 DATA0(-)
STB-RESET R3105 IC3101(5/7) IC3101(5/7) 10 CLOCK(+)
R3110 R3114 100 R3179 100
STMTIME1 33 33 U1 KEY-IN1 HDMI-CEC Y3 11 TMDS CLOCK SHIELD
D3101 STMCECPUL T6 12 CLOCK(-)
OPEN R3150 R3161 100 R3134 39
10K T2 PROTECT3 HDMI0-SCL T7 13 HDMI-CEC
CONTINUE R3160 100 R3137 39
DIGITAL 7 U5 PROTECT1 HDMI0-SDA W6 14 NU
R3139 39
STB-RESET AD5 STB-RESET HDMI1-SCL R9 15 HDMI-CLOCK
R3162 22 R3140 39
LCD-P-ON W2 LCD-P-ON HDMI1-SDA AE3 16 HDMI-DATA
R3133 100 R3141 39 R3781 R3780
BACKLIGHT-SW W3 BACKLIGHT-SW HDMI2-SCL V7 R3784 47K 47K 17 GND
R3142 39 10K
PROTECT3 Y2 P-ON-H2 HDMI2-SDA AA5 18 +5V
PROTECT1 C3759 R3785 R3710 R3779 19 HOT PLUG DETECT
R3138 OPEN 0.1 47K 10K 1K
P-ON-H2 AB6 P-ON-H2
HP-MUTE W7 HP-MUTE HDMI0-HPD R7 R3707 R3783
10K Q3702
2 CONTINUE
DIGITAL 6
SP-MUTE
W5 STMTIME1
AA2 SP-MUTE
HDMI1-HPD U2
HDMI2-HPD U6
HDMIO-5V AB5
2SC4081UBTLQ
(SWITCHING)
OPEN
JK3715
1
HDMI-
CONNECTOR-2
DATA2(+)
2 TMDS DATA2 SHIELD
HDMI1-5V AA6 3 DATA2(-)
HDMI2-5V AC3 4 DATA1(+)
R3863
C3127 27K 5 TMDS DATA1 SHIELD
0.1 R3152 R3153
IC3103 4.7K 4.7K D3722 6 DATA1(-)
1SS400
M24C16-WMN6TP R3865 7 DATA0(+)
(MEMORY) R3156 39 22
AC2 STM-SCL 8 TMDS DATA0 SHIELD
1 A0 VCC 8 R3157 39 R3165 39 9 DATA0(-)
AC1 STM-SDA VGA-SCL Y7
R3158 22 R3178 39 10 CLOCK(+)
2 A1 WP 7 U4 STM-EEPROM-WP VGA-SDA AD3
NU U7 11 TMDS CLOCK SHIELD
3 A2 SCL 6 R3151
10K HDMI-UART-CTRL Y6 12 CLOCK(-)
4 VSS SDA 5 13 HDMI-CEC
14 NU
R3730 C3719 15 HDMI-CLOCK
0 220P 16 HDMI-DATA
R3777 R3773 R3774 17 GND
Q3706 R3714 10K 47K 47K
OPEN 10K Q3704 18 HDMI+5V
2SC4081UBTLQ C3750 R3778 R3712 R3775 19 HOT-PLUG-DETECT
R3720 (SWITCHING) 0.1 47K 10K 1K
R3771 33K
1 R3772
OPEN
OPEN
C3717
R3711
10K Q3703
2SC4081UBTLQ
(SWITCHING)
R3776
OPEN
220P
R3717
0
CONTINUE R3715
DIGITAL 5 Q3705 10K
2SC4081UBTLQ CONTINUE
UART1TX (SWITCHING) R3716 DIGITAL 6
UART1RX 33K VGA-SCL
VGA-SDA
AQ AR AS AT AU AV
10-20 PL13.9BSCD8
Digital Main 1 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
R3085 DIGITAL 4
OPEN
DIGITAL MAIN CBA UNIT P-ON+5V
P-ON+21V
R3630 P-ON+3.3V
(NO CONNECTION) CN3013 7.5 R3045
LCD+12V 1 18K R3047 R3046 C3057 C3058 R3039 PROTECT3
R3044 3.9K 12K 47/25V 0.1 OPEN
LCD+12V 2 C3166 C3167 11K D3008 CONTINUE
OPEN OPEN OPEN DIGITAL 3
LCD+12V 3 R3048 CELL-PWR-CTRL
LCD+12V 4 Q3007 1K
2SC4081UBTLQ VCOM-PWM
GND 5 (SWITCHING) C3000
4 GND 6
GND 7
NU 8
R3632
OPEN
D3624
OPEN
OPEN
R3037 R3038
C3514
1000P
TO LCD PANEL
CN3006 ASSEMBLY
30 LCD+21V
29 LCD+21V
SELLVDS 9 R3135 OPEN OPEN 28 GND
OPEN R3622 27 VCOM-PWM
NU 10 OPEN
GND 11 26 PWR-CTRL
R3621 C3628 R3035 25 P-ON+3.3V
RX0(-) 12 OPEN OPEN 0
C3624 C3623 C3622 C3621 C3512 24 GND
RX0(+) 13 OPEN OPEN OPEN OPEN R3524 OPEN
D3623 10K 23 ML0(+)
GND 14 OPEN
IC3621 22 ML0(-)
RX1(-) 15 OPEN
C3627 21 ML1(+)
RX1(+) 16 OPEN
1 SS BST 8 R3028 20 ML1(-)
GND 17 C3625 R3627 0
OPEN OPEN 19 ML2(+)
RX2(-) 18 2 EN IN 7
C3629 R3623 C3626 18 ML2(-)
RX2(+) 19 OPEN OPEN OPEN
3 COMP SW 6 17 GND
GND 20 C3630
RXCLK(-) 21 4 FB GND 5 OPEN L3621 16 MLCLK(+)
R3625 R3624 OPEN 15 MLCLK(-)
RXCLK(+) 22 OPEN OPEN R3626 R3628
OPEN OPEN 14 GND
GND 23
RX3(-) 24 13 ML3(+)
RX3(+) 25 R3631 R3629 D3622 D3621 C3636 C3635 C3634 C3633 C3632 C3631 12 ML3(-)
3 GND 26
BIST 27
NU 28 R3161
OPEN
R3162
OPEN
OPEN OPEN OPEN OPEN OPEN OPEN OPEN 4.7 4.7 OPEN 11 ML4(+)
10 ML4(-)
9 ML5(+)
NU 29 8 ML5(-)
GND 30 R3129 7 GND
OPEN 6 TP
R3130 5 POL
(NO CONNECTION) CN3014 OPEN
LCD+12V 30 4 CPV
LCD+12V 29 3 OE1
LCD+12V 28 2 OE2
LCD+12V 27 1 STV
GND 26
CN3001 (NO CONNECTION)
GND 25 31 LCD+21V
C3641 OPEN
C3642 OPEN
C3643 OPEN
C3644 OPEN
C3645 OPEN
C3646 OPEN
C3647 OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
GND 24 *1 30 LCD+21V
NU 23 IC3005(1/6)
R8A05011BG-U0 29 LCD+21V
C3654
C3655
C3648
C3649
C3650
C3651
C3652
C3653
C3656
C3657
C3658
C3659
C3660
C3661
SELLVDS 22 DIGITAL SIGNAL PROCESS 28 GND
NU 21 /MAIN MICRO CONTROLLER
27 VCOM-PWM
GND 20 26 PWR-CTRL
RX0(-) 19 R16 25 P-ON+3.3V
RX0(+) 18
2 GND 17
RX1(-) 16
RX1(+) 15
R15
P14
P13
N16
24
23
22
21
GND
ML0(+)
ML0(-)
ML1(+)
GND 14 N15 20 ML1(-)
RX2(-) 13 LVDS P16 19 ML2(+)
RX2(+) 12 TX
P15 18 ML2(-)
GND 11 T16 17 GND
RXCLK(-) 10 T15 16 MLCLK(+)
RXCLK(+) 9 R14 15 MLCLK(-)
GND 8 T14 14 GND
RX3(-) 7 R13 13 ML3(+)
RX3(+) 6 T13 12 ML3(-)
GND 5 11 ML4(+)
BIST 4 NU M16 10 ML4(-)
NU 3 NU M13 9 ML5(+)
NU 2 TO DIGITAL NU N14 8 ML5(-)
MAIN 2
GND 1 IC3005(2/6) NU N13 7 GND
R3644 100
TP L13 6 TP
(NO CONNECTION) CN3601 R3645 100
GND 1 POL M15 5 POL
R3641 100
1 NU
NU
NU
2
3
4
R3131
OPEN
C3161
OPEN
CPV
OE
OE2
STV
L16
L15
L14
M14
R3642
R3643
R3646
100
100
100
4
3
2
1
CPV
OE1
OE2
STV
OPEN
100P
OPEN
OPEN
OPEN
OPEN
100K
100K
100K
100K
100K
100K
(NO CONNECTION) CN3602 NU K15
GND 1 R3088
4.3K
R3041
R3117
R3118
R3119
R3120
R3132
C3666
C3662
C3663
C3664
C3665
C3667
NU 2
NU 3
NU 4
A B C D E F
10-21 PL13.9DSCD1
Digital Main 2 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
DIF-OUT1
DIF-OUT2
74LVC1G126GW
IF-AGC
(BUFFER GATE)
+3.3V
GND
SDA
SCL
1 VCC 5
C3214 Q3301
1 2 3 4 5 6 7 2 0.1 RU1L002SNTL
(BUFFER) Q3302
4 C3903 0.1
C3902 0.1
3 GND 4 RU1L002SNTL
(BUFFER)
CONTINUE
DIGITAL 6
VGA-SDA
VGA-SCL
IC3014
74LVC1G126GW
(BUFFER GATE)
1 VCC 5 CONTINUE
L3913 DIGITAL 4
2.2uH
2 P-ON+3.3V
C3905 C3901 D3901 C3934 C3909 C3175 C3176 R3204 P-ON+5V
10 220/6.3V MM5Z5V6B OPEN OPEN 33P 33P 2.7K 3 GND 4
3 MAIN 5
IC3005(5/6) DEMODULATOR
/MPEG
DECODER
A12
C3173
33P
C3172
R3251
10
R3250
R3333
10
R3343
OPEN 13 8 3
2 TO DIGITAL
MAIN 3
NU
NU
B9
D9
C3708 R3701
JK3702
COMPONENT
-Y/VIDEO-IN
DIGITAL IC3005(3/6) 0.1 OPEN
R3711
SIGNAL 10K
PROCESS COMPONENT
TO DIGITAL R3702 -Pb-IN
MAIN 3 OPEN
IC3005(3/6) R3710
100
COMPONENT
C3707 R3712 Q3701 R3703 -Pr-IN
1 10K 2SC4081UBTLQ OPEN
(BUFFER)
R3709 C3706 JK3701
C3335 220 1
TO DIGITAL TO DIGITAL 2.2 C3285 0.1 DIGITAL
NU B10 R3708 C3709 AUDIO-OUT
MAIN 6 MAIN 1 C3286 0.1 110 100P (COAXIAL)
IC3005(6/6) IC3005(1/6) NU A11
C3336 1
NU D10 AUDIO(L)-IN
R3704
100K
AUDIO(R)-IN
R3705
100K CONTINUE
DIGITAL 5
1 SCL
SDA
AUDIO(L)-IN
AUDIO(R)-IN
CONTINUE
DIGITAL 5
SPDIF
G H I J K L
10-22 PL13.9DSCD2
Digital Main 3 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
C3009 R3082 *1
OPEN 100 IC3005(3/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS C3184
R3064 C3050 /MAIN MICRO CONTROLLER 18P
100 0.1
M5 SD-VREF0
R3065 C3051 N3 GND X3001
100 0.1 XIN25 H15 R3223 25MHz C3183
1K 20P CN3012 (NO CONNECTION)
4 IC3002
SD-DQ15
SD-DQ14
R8
N8
SD-DQ15
SD-DQ14
XOUT25 H16
ASEBRKAK-N F15
R3527 OPEN
1
2
3
AL+3.3V
GND
ASEBRKAK-N
K4T51163QJ-BCE7 SD-DQ13 ASEMD0 F16 4 ASEMD0
(DDR2 SDRAM) P7 SD-DQ13 TRST-N E16 5 TRST-N
SD-DQ12 R6 SD-DQ12 R3525 OPEN
C3029 0.1 TCK E15 6 TCK
*A VDD SD-DQ11 P6 SD-DQ11 R3526 OPEN
C3030 0.1 VREF J2 TDI D16 7 TDI
SD-DQ10 N7 SD-DQ10
C3031 0.1 C3010 R3083 TDO D15 8 TDO
0.1 100 SD-DQ9 T5 SD-DQ9
C3032 0.1 TMS E14 9 TMS
CKE K2 SD-DQ8 P8 SD-DQ8 TO DIGITAL
C3033 0.1 MAIN 2 R3522 10 CPU-RESET-N
E2 NU CK J8 SD-DQ7 P4 SD-DQ7 IC3005(2/6) 10K
C3034 0.1
A2 NU CK K8 SD-DQ6 T3 SD-DQ6 R3395 CN3010 (NO CONNECTION)
C3035 0.1 R3049 4.7K
R8 NU CS L8 150 SD-DQ5 R4 SD-DQ5 1 P-ON+5V
C3037 0.1 R3468 100
R7 NU RAS K7 SD-DQ4 T2 SD-DQ4 TXD0 G15 2 UART0-TX
C3038 0.1 R3469 100
R3 NU CAS L7 SD-DQ3 P3 SD-DQ3 RXD0 G16 3 UART0-RX
C3039 0.1 C3253
WE K3 SD-DQ2 T4 SD-DQ2 OPEN 4 GND
C3040 0.1 C3254 C3255 R3396
1-O3 B7 UDQS BA2/NU L1 SD-DQ1 R3 SD-DQ1 OPEN OPEN 4.7K
C3041 0.1
2-O3 A8 UDQS/NU BA1 L3 SD-DQ0 N4 SD-DQ0
C3140 0.1 CONTINUE
3-O3 B3 UDM BA0 L2 3-M3 T6 SD-UDM DIGITAL 2
SD-DQ15 B9 DQ15 A12 R2 6-M3 R5 SD-LDM COMP-DET
R3516 100
SD-DQ12 2-M3 BACKLIGHT-ADJ F3
3 SD-DQ10
SD-DQ9
SD-DQ14
B1
D9
D1
D3
DQ12
DQ10
DQ9
DQ14
A11
A10/AP
A9
A8
P7
M2
P3
P8
1-M3
5-M3
4-M3
T7
R7
N5
P5
SD-UDQSN
SD-UDQS
SD-LDQSN
SD-LDQS
VCOM-PWM F2
GND J14
R3517 100 CONTINUE
DIGITAL 5
CPU-RESET-N
SD-DQ13 D7 DQ13 A7 P2
SD-DQ11 C2 DQ11 A6 N7
SD-DQ8 R3030 33x4 H1 SD-A4 R3511 22 CONTINUE
C8 DQ8 A5 N3 CELL-PWR-CTRL D1 DIGITAL 4
4-O3 F7 LDQS A4 N8 H3 SD-CAS GPY10 E13 GPY10
5-O3 E8 LDQS/NU A3 N2 J2 SD-A11 CPU-RESET-N
6-O3 J1 SD-A0 R3211 100
F3 LDM A2 M7 R3031 33x4 P-ON-H2 B16 P-ON-H2
SD-DQ3 J4 SD-A10 R3233 22
F9 DQ3 A1 M3 HP-MUTE G13 BACKLIGHT-ADJ
SD-DQ2 L1 SD-A1 R3188 22
F1 DQ2 A0 M8 BACKLIGHT-SW E2 BACKLIGHT-SW
SD-DQ7 H9 DQ7 ODT K9 K4 SD-BA1
R3503
SD-DQ6 L2 SD-A9 10K CONTINUE
H1 DQ6 R3032 33x4 DIGITAL 1
SD-DQ4 H3 DQ4 L4 SD-WE CELL-PWR-CTRL
SD-DQ1 VSS *B N2 SD-BA0
H7 DQ1 TO DIGITAL VCOM-PWM
SD-DQ5 G2 DQ5 P1 SD-BA2 MAIN 2 R3510 22K
SD-DQ0 M3 SD-A3 IC3005(2/6)
G8 DQ0 CONTINUE
R3033 33x4 M1 SD-A5 DIGITAL 5
R3515 4.7K
M2 SD-A12 LED1 D14 LED1
*A:A1,A9,C1,C3,C7,C9,E1,E9, R3213 22
G1,G3,G7,G9,J1,J9,M9,R1 L3 SD-CKE REMOTE C14 REMOTE
R3217 22
2 *B:A3,A7,B2,B8,D2,D8,E3,E7,
F2,F8,H2,H8,J3,J7,N1,P9 R3034 33x4
N1
J3
K3
SD-A7
SD-RAS
SD-A6
AUDIO-MUTE C1
R3234
OPEN
K1 SD-A2
CONTINUE
K2 SD-ODT DIGITAL 4
IC3006 H2 SD-A8 R3201 P-ON+1.8V
F25L32QA-100PAG2S R3102 R3016 33 R3215 22 33K
10K R2 SD-CLK COMP-DET N12 P-ON+3.3V
(MEMORY) R3084 10
R1 SD-CLKN AL+3.3V
1 CS VCC 8 R3087 10
R3107 H4 NU P-ON+5V
10K C3073 R3070 150
2 SO NU 7 0.1
R3089 47
P12 CS
3 WP SCK 6 R3092 47 CONTINUE
R11 SOUT DIGITAL 5
R3093 47
4 GND SI 5 P11 SIN C3072 10 HP-MUTE
R3094 47 NU H14
R3479 T11 SCK AUDIO-MUTE
10K R3095 22
T9 VBUS-EN BACKLIGHT-SW
R9 VBUS-ST
R10 USBDP
(USB JACK) CN3009 C3246 C3348 T10 USBDN
1 220/6.3V R3099 5.6K
BUS-POWER 1 P10 NU
USBDN 2 IC3019
1 USBDP
GND
3
4 L3025
EXC24CG900U
AP2151WG-7
(HIGH SIDE SW)
1 OUT IN 5
C3327
2 GND 1
3 /FLAG RN 4
R3480
10K
DIGITAL MAIN CBA UNIT
M N O P Q R
10-23 PL13.9DSCD3
Digital Main 4 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
*1 DIGITAL 3
IC3005(4/6) R3221 P-ON+1.8V
R8A05011BG-U0 100
DIGITAL SIGNAL PROCESS P-ON+3.3V
/MAIN MICRO CONTROLLER R3222 AL+3.3V
10K L3027
BEAD P-ON+5V
VCC33STB F12
C3160 R3106 R3100 R3036
4 VCC33STB G12
VDD12STB E12
0.1
D
G
S
Q3006
2SA1576UBTLQ
47K
R3105
10K
22K
Q3101
2SC4081UBTLQ
(SWITCHING)
D3105
OPEN D3103
HSC119
R3424
100 IC3004
100
CONTINUE
DIGITAL 6
P-ON+3.3V
(SWITCHING) BD00IA5WEFJ-E2 AL+3.3V
L3030
0 Q3013 Q3005 C3265 R3138 (+1.2V REG.) P-ON+3.3V(1)
C3181 SSM3K309T 2SC4081UBTLQ 10 OPEN
0.1 (SW+12V) R3423 D3115 1 VOUT VCC 8 P-ON+5V
(SWITCHING) R3097 47K HSC119
1.5K C3024 CONTINUE
D3101 2 FB NU 7 10 DIGITAL 2
VDD12 *C HSC119 P-ON+3.3V
R3061 R3060 C3019
C3123 C3124 C3125 C3126 C3132 C3133 D3102 10K 2.7K 0.022 3 GND NU 6 P-ON+5V
1 1 1 1 10 10 HSC119 R3059 R3062
2.7K 1.8K
4 NU EN 5
CONTINUE
C3127 C3128 C3129 C3130 C3134 R3043 C3086 DIGITAL 1
1 1 1 1 1 R3228 R3086 180 10 P-ON+5V
OPEN Q3011 4.7K
OPEN R3008 P-ON+21V
AVDD12 M10 C3237 R3227 D3104 C3131 1
OPEN OPEN HSC119 Q3003 1 P-ON+3.3V
C3135 R3077 2SC4081UBTLQ
0.1 L3021 10K (SWITCHING) PROTECT3
BEAD IC3601
AVDD12 E8 AP2121AK-3.3TRE1 L3003
AVDD12 F8 C3118 C3136 C3114 C3115 R3605 (+3.3V REG.) R3079 Q3004 OPEN
10 1 10 10 0 10K 2SC4081UBTLQ IC3007
AVDD12 F9 1 VIN VOUT 5 (SWITCHING) BD00IC0WEFJ CONTINUE
C3609 C3610 (+1.8V REG.) DIGITAL 5
1 2 GND R3606 1 RESET
3 VDDCLK G11
C3139
0.1
R3608
4.7K
C3611 R3609
OPEN OPEN
3 CE NU 4
OPEN
R3607
OPEN
D3106
HSC119 R3111
10K
R3110
10K
C3075
0.022
1 VOUT
2 FB
VCC 8
NU 7
C3069
10
C3068
OPEN
PROTECT1
PROTECT3
3 GND NU 6
R3109 R3103 CONTINUE
3.3K 1.8K DIGITAL 5
VCCQ18 H5 4 NU EN 5
P-ON+3.3V
VCCQ18 J5 C3326 C3325 C3324 C3343 C3264 C3079 C3087
10 OPEN OPEN 10 OPEN 220/6.3V 10 CHECK+1.8V
VCCQ18 M4 AL+3.3V
VCCQ18 T1 P-ON+5V
C3322 C3321 C3320 C3319 C3318
VCCQ18 M6 10 OPEN 10 10 10 P-ON+3.3V(1)
VCCQ18 N6 AMP+13V
VCCQ18 M7 C3141 C3142 C3143 C3144 C3145 C3080 C3103 C3007 C3102 C3003 C3002
1 1 1 1 1 4.7 OPEN 0.1 IC3008 4.7 0.1 OPEN IC3001
VCCQ18 M8 MP1472GJC452Z MP1472GJC452Z
L3019 (+1.2V REG.) (+3.3V REG.)
OPEN C3083 C3013
AVDD33 E10 0.015 0.047 CONTINUE
C3148 C3149 C3150 D3113 1 SS BST 8 1 SS BST 8 DIGITAL 3
AVDD33 C2 1 10 1 MM5Z5V6B R3133 C3091 R3091 C3092 GPY10
10K OPEN C3085 0 OPEN C3014
AVDD33 C3 2 EN IN 7 R3141 0.1 2 EN IN 7 R3057 0.1 CPU-RESET-N
C3090 C3088 R3137 OPEN C3119 C3017 R3001 OPEN
AVDD33 E11 1 4700P 2.7K OPEN 2200P 8.2K P-ON-H2
3 COMP SW 6 3 COMP SW 6
BACKLIGHT-ADJ
L3026 4 FB GND 5 4 FB GND 5
BEAD L3009 L3002 BACKLIGHT-SW
AVDD33 D6 10uH 33uH
2 L3006
BEAD
C3151
1
C3152
1
C3154
1
D3114
MM5Z5V6B C3099 R3142 R3149 C3094 C3096 C3065 C3097 R3602 D3005 R3004 C3020 C3021 C3059 R3014 R3601
OPEN
OPEN OPEN 3.9K 330/4V 10 10 OPEN OPEN PTZTE255.1B 33K 330/4V 10 10 270 OPEN
220
100
100
100
AVDD33 E6 R3145 C3606 R3003 C3605
C3155 C3156 1.2K OPEN 6.2K OPEN
1 1
R3013
R3011
R3009
R3072
R3068
D3006 R3143 R3002 TO POWER SUPPLY
VCCQ33 G4 PTZTE255.1B 15K 15K CN3701 CBA CN501
VCCQ33 F5 C3157 C3158 C3159 1 LED-CONT(NU)
1 1 1 D3994 OPEN
VCCQ33 L12 2 PROTECT1
D3995 OPEN
VCCQ33 K13 C3022 C3001 C3105 R3108 D3112 D3107 3 PROTECT3
4.7 0.1 OPEN 47K MM5Z12B HSC119
VCCQ33 J12 4 RESET
AVDD33 N11 R3140 5 BACKLIGHT-SW
IC3003 18K Q3009
MP1472GJC452Z 2SC4081UBTLQ 6 P-ON-H2
C3028 (+5V REG.) R3112 R3115 Q3103 C3238 R3139 (SWITCHING) 7 BACKLIGHT-ADJ
VSS *D 0.047 10K OPEN 2SA1576UBTLQ R3101 OPEN 1K
1 SS BST 8 (SWITCHING) 1K 8 AL+3.3V
R3098 C3095 C3063 C3994 9 GND
0 OPEN C3042 OPEN OPEN
*C:G5,G6,H6,J7,J11,J13,K6,K7, 2 EN IN 7 R3054 0.1 Q3102 C3107 R3104 10 GND
K11,L8,L9,M9,M11,N9,P9. C3121 C3043 R3005 OPEN 2SC4081UBTLQ 1 1K
OPEN 4700P 4.3K R3113 11 GND
*D:D2~D5,D12,E3~E5,E7,E9,F4,F6, 3 COMP SW 6 (SWITCHING) 10K C3604 C3603 D3602
F7,F10,F11,G7~G10,H7~H13,J6, 10 1 MM5Z5V6B 12 GND
J8~J10,K5,K8~K10,K12,L5~L7, 4 FB GND 5 L3005 R3114 R3051
L10,L11,P2,T8 22uH 47K 100 13 GND
14 GND
R3012 C3056 C3074 C3053 R3603 D3007 15 AMP+13V
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
33K 10 10 OPEN OPEN OPEN C3995 16 AMP+13V
R3007 C3607 OPEN
12K OPEN 17 AMP+13V
C3062
C3008
C3006
C3004
C3055
C3048
18 AMP+13V
R3006
10K 19 GND
20 P-ON+21V
C3996 21 P-ON+21V
OPEN
22 P-ON+21V
DIGITAL MAIN CBA UNIT 23 P-ON+21V
S T U V W X
10-24 PL13.9DSCD4
Digital Main 5 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4
P-ON+3.3V
CHECK+1.8V
AL+3.3V
P-ON+5V
P-ON+3.3V(1) *1
IC3005(5/6)
AMP+13V R8A05011BG-U0
CONTINUE DIGITAL SIGNAL PROCESS
/MAIN MICRO CONTROLLER
4 DIGITAL 3
LED1
REMOTE
R3552 R3558
Q3502
2SA1576UBTLQ
(LED DRIVE)
R3559
R3312 10K
D13 CHECK+1.8V NU G1
NU E1
TO FUNCTION CBA 100 OPEN 10K
UNIT CN4052 CN3101 NU G2
CONTINUE
SDA(NU) 1 R3560 R3210 R3402 DIGITAL 6
100K 100 0
SCL(NU) 2 HPD-SINK K14 HPD-SINK
GND 3 PWR J16 PWR
C3555 R3320 R3216 R3401
KEY-IN1 4 OPEN OPEN 100 0
REMOTE 5 C3559 R3551 R3555
OPEN 100 OPEN R3220
LED1 6 R3183 33K
R3318 22K
R3317 10K
R3319 10K
OPEN Q3010 R3219
LIGHT 7 OPEN 22
P-ON+5V 8 C3553 C3556 C3558 HP-DET K16
OPEN OPEN OPEN D3201
AL+3.3V 9 MM5Z5V6B
C3554 C3560 Q3501 R3185 CONTINUE
1 OPEN 2SC4081UBTLQ OPEN R3191 DIGITAL 3
(LED DRIVE) 100
C3329 0.01 RESET J15 CPU-RESET-N
C3551 33P R3184 R3186 D3111
C3552 33P R3553 D3501 OPEN OPEN A15 KEY-IN1 MM5Z5V6B
CONTINUE 100 MM5Z5V6B R3314 22
DIGITAL 4 B13 PROTECT3
R3315 OPEN
RESET A13 LIGHT-SENS
R3316 22 IC3009
PROTECT1 C13 PROTECT1 R3178 PST8429UR R3182
3 PROTECT3
C3231
C3328
OPEN
0.22
C12 LPF
TO DIGITAL TO DIGITAL
MAIN 2 MAIN 6
220 (RESET)
1 GND OUT 4
56K
1000P
1000P
R3556 R3557 IC3005(2/6) IC3005(6/6) C3116
OPEN
OPEN
OPEN
OPEN
CONTINUE 10 10 R3340 10K 2 VDD CD 3 1000P
DIGITAL 2 NU D11
C3219 10 D3108 C3106 C3113
SCL NU D7 OPEN 1 0.033
C3229
R3502
C3227
R3501
C3233
C3232
C3220 10
SDA NU C6
R3335 18K C3217 2.2 C3216 10
AUDIO(L)-IN A8 NU C5
R3336 18K C3218 2.2
AUDIO(R)-IN B8 AUDIO NU B6
C3223 1 I/F CONTINUE
R3995 R3862 B7 NU A6 R3209 DIGITAL 2
CONTINUE 10K 10K C3224 1 100
DIGITAL 3 A7 N10 SPDIF
HP-MUTE
AUDIO-MUTE R3865
10K
BACKLIGHT-SW
R3561 C3860 R3866 C3862
10 0.1 100K OPEN
R3867 R3868
0 OPEN
R3809 R3810 R3864
OPEN OPEN 1K R3851 C3851
15K 1 C3853
220/6.3V
R3861 R3853 JK3703
10K Q3861 OPEN C3856 R3856 HEADPHONE
C3825 C3824 2SC4081UBTLQ 1000P 10K JACK
2 R3814
OPEN
Q3803
R3870
220
R3813
OPEN
R3822
10
IC3801
TPA3110D2PWPR
(AUDIO AMP)
1 1000P (SWITCHING)
R3869
OPEN
4
GND
3 2 1
MUTE
IC3851
BH3547F
C3861
0.1
1 R3823
C3871
2200P
12
13 NU
14 PBTL
17
PVCCR 16
PVCCR 15
OPEN
C3806
OPEN L3804
10uH
1000P 1 OPEN 1
2
3
4
SP(L)+
SP(L)-
SP(R)-
SP(R)+
OPEN SP3802
C3831 C3826 C3829 R3804 C3814 C3823 D3804 SPEAKER
100/16V 100/16V 100/16V OPEN 1000P 1 OPEN R-CH
C3810
OPEN
Y Z AA BB CC DD
10-25 PL13.9DSCD5
Digital Main 6 Schematic Diagram [TYPE D]
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3005.
IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
CONTINUE
DIGITAL 4 HDMI-
P-ON+3.3V JK3002 CONNECTOR-2
C3316 C3421 C3423 C3425 C3426 1 TMDS-D2(+)
AL+3.3V 10 1 1 1 1 2 D-SHIELD0
P-ON+3.3V(1)
3 TMDS-D2(-)
P-ON+5V
D3993 C3420 C3422 C3424 C3427 4 TMDS-D1(+)
OPEN OPEN OPEN OPEN OPEN
5 D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
4 *1
IC3005(6/6)
R8A05011BG-U0
DIGITAL SIGNAL PROCESS
8
9
10
11
D-SHIELD2
TMDS-D0(-)
TMDS-CLOCK(+)
C-SHIELD0
/MAIN MICRO CONTROLLER Q3014
RU1L002SNTL R3405 12 TMDS-CLOCK(-)
(BUFFER) 100
13 HDMI-CEC
TO DIGITAL TO DIGITAL 14 NU
MAIN 2 MAIN 5 R3415
IC3005(2/6) IC3005(5/6) 82K R3486 15 HDMI-CLOCK
3.9K 16 HDMI-DATA
D3057 IC3018 C3202 C3203 R3275 R3278 17 GND
VIDEO AUDIO RB751S-40 OPEN OPEN 47K 47K
DECODER DECODER 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TMDS351PAGR
R3237 (HDMI SW) 18 +5V
GND
VCC
GND
VCC
GND
NU
27K C3023 R3066 R3055 19 HOT PLUG DETECT
HDMI-CEC B15 0.1 2.7K 1K
17 HOT-PLUG- 64 Q3008
DETECT3 R3063 2SC4081UBTLQ
18 63 1K (SWITCHING)
C3989 C3988 R3489 R3058
B1 OPEN OPEN 10K 19 VCC 62 10K
A1
20 VCC 61 HDMI-
B2 JK3003 CONNECTOR-3
A2 21 60 1 TMDS-D2(+)
HDMI
I/F B3 C3987 C3986 2 D-SHIELD0
OPEN OPEN 22 GND 59
A3 3 TMDS-D2(-)
B4 23 GND 58 4 TMDS-D1(+)
A4 5 D-SHIELD1
3 C3985
OPEN
C3984
OPEN
24
25 VCC
26
HDMI SW 57
56
VCC 55
6
7
8
TMDS-D1(-)
TMDS-D0(+)
D-SHIELD2
C3990 9 TMDS-D0(-)
1P 27 54 10 TMDS-CLOCK(+)
R3488 R3487
4.7K 4.7K 11 C-SHIELD0
28 GND 53
12 TMDS-CLOCK(-)
SCL-SINK C16 29 SCL-SINK 52 13 HDMI-CEC
14 NU
SDA-SINK C15 30 SDA-SINK 51
R3514 15 HDMI-CLOCK
100
HPD-SINK F13 31 HOT-PLUG-
DETECT-SINK
HOT-PLUG- 50
DETECT2 16 HDMI-DATA
R3508 C3204 C3205 R3214 R3212
22 17 GND
HOT-PLUG-
HDMI-SEL0 G3 32 HDMI- NU 49 OPEN OPEN 47K 47K
SEL0
DETECT1
R3994 R3496 18 +5V
HDMI-
OPEN 4.7K C3005 R3019 R3010
SEL1
1K 19 HOT PLUG DETECT
VCC
GND
VCC
0.1 2.7K
NU
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Q3001
R3509 R3018 2SC4081UBTLQ
22 1K (SWITCHING)
HDMI-SEL1 F1
R3497 R3017
4.7K R3992 10K
R3990 0
OPEN HDMI-
R3236 C3185 R3270 C3187 JK3004 CONNECTOR-1
560 0.01 2.2K 2.2 R3991 1 TMDS-D2(+)
10K
EXT-RES C4 C3186 2 D-SHIELD0
2 PLL-XFC-A B5
PLL-XFC-P A5 R3271
3K
4700P
C3188
2200P
3
4
5
TMDS-D2(-)
TMDS-D1(+)
D-SHIELD1
6 TMDS-D1(-)
7 TMDS-D0(+)
8 D-SHIELD2
9 TMDS-D0(-)
10 TMDS-CLOCK(+)
PWR M12 11 C-SHIELD0
R3193 12 TMDS-CLOCK(-)
4.7K
HDMI-SCL G14 13 HDMI-CEC
HDMI-SDA F14 D3003 D3001 C3208
RB751S-40 RB751S-40 OPEN 14 NU
R3192
4.7K 15 HDMI-CLOCK
16 HDMI-DATA
C3206 C3207 D3002 R3273 R3276 17 GND
CONTINUE OPEN OPEN RB751S-40 47K 47K
DIGITAL 5 18 +5V
HPD-SINK R3022 R3024 C3018 R3040 R3025 19 HOT PLUG DETECT
10K 10K 0.1 2.7K 1K
PWR
R3023
IC3011 22K Q3002
BU9883FV-WE2 2SC4081UBTLQ
(HDMI SERIAL EEPROM) R3029 (SWITCHING)
CONTINUE 1K
DIGITAL 2
VGA-SDA 1 VCC1 VCC2 16 R3027
10K
1 VGA-SCL
R3451
10K
R3453
1.5K
2 SCL1
3 SDA1
4 WPB
SCL2 15
SDA2 14
NU 13
R3073
0
R3074
0
C3192 0.1 R3075
R3281 5 VCC-OUT GND 12 0
Q3451 100
2SC4081UBTLQ 6 SDA0 SDA3 11 R3076 R3078
(SWITCHING) R3282 0 OPEN
R3452 100
10K 7 SCL0 SCL3 10 R3081 R3080
0 OPEN
8 VCC0 VCC3 9
DIGITAL MAIN CBA UNIT C3191
0.1
EE FF GG HH II JJ
10-26 PL13.9DSCD6
Power Supply CBA Top View [TYPE A, TYPE B, TYPE C, TYPE F]
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
CAUTION !
when troubleshooting this type of power supply circuit,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, a variable isolation transformer is required.
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail. NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
C617
BA31M0F0102 4
J163
J141
GND
/BLACK
FH602 FH601
LIVE
J169
/WHITE BC1001
T 2.5A L/250V
F602
CN601
F601 GND D652
C1005
NEUTRAL BC1002
4A/125V P-ON+21V
C1001
J154
J139
D660
GND
J140
R601 P-ON+21V
IC601
RISK OF FIRE- IC602
AMP+13V J136 GP001
R1
SA601
REPLACE FUSE AS MARKED
02
P-ON-H2+ J138
C1006
0
1
CO
2
J133 C653
J171
FG
FG
CN1001
LD
C650
03 D651
L1001
C6
7
C652
HO
C604
6
T601
T
50
J159
D6
JS601
JS602
C1018
C651
BL-ADJ
C606
J149
J142
D608
L601
GATE
P-ON+21V
FG
J135
C611 C654
J137
J148
+13V
+13V
J134
+13V
J155
LED+21V
C614
J167
GND
C655
PROTECT3
BL-ADJ
R6
BL-SW
D655
J157
J160
J158 GND
D607 BC601 76
2
J161
R611
L602
D604
J144
R602 C602
JS605
JS606
C656
Q658
C6
JS603 +B
05
RESET J145
D601
JS604 +B J143
C616 R678
BC603 P-ON+21V
D662
Q657
D654
D603
ALL+3.3V
LED-CONT
C662
C657
J150
J151
J168
GP002
ALL+3.3V
J147
J152
No.2
SA602 C663
GND
ALL+3.3V
D602 2 22
J153
BC602
J146
GT601
GND
GND
1
23
D C CN501
B A
10-27 BA31M0F01024
Power Supply CBA Bottom View [TYPE A, TYPE B, TYPE C, TYPE F]
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
CAUTION !
when troubleshooting this type of power supply circuit,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, a variable isolation transformer is required.
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail. NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
BA31M0F0102 4 C617
J163
J141
GND
R657 FH601 FH602
J169
BC1001 R659
CN601
C1005
BC1002
D652 R660 GND F601
F602
4A/125V
T 2.5A L/250V
GND J170 GND
C1001
R675
J154
J139
D660
GND
J140 D661
C1002 P-ON+21V R674
Q653 R601
GP001 C1003 IC601
0 C1004 J136 AMP+13V R667 C666 R661 IC602
02 SA601
C1009 R1 J138 P-ON-H2+ R658
C1006
R669 C660
1
C610
2
J171
D652A
FG
C1008 R654 FG
6 CN1001
R1022 C652
C604
R622
R1017
C1015 L1002 R1021 C621
T601 D621 R608
R1011 IC1001 D650A R621 C608 Q602
D6
50
J159
JS601
C609
JS602
C1018 D605 R606
R1012 R607 C607
R1013 R612
C651 R609
BL-ADJ
J149
C1016 J142
D608
L601
R1014 C1012
GATE
D1002
P-ON+21V
R1015 C1013 FG
J135
R1008 C654
C1011 C611
J137
R1016
J148
+13V
+13V
R1001
J134
D608A
+13V
R1009
R1005 R1002 J155
R1006
D654A
R1007 C1014 LED+21V C1010 R615
C614
R1010
R1004 R617
R1003
GND J162 R616
Q601
BC604
J167
GND
C655
PROTECT3
D653A
BL-ADJ
D607 D607A
BL-SW
R677 D655
J157
76
J160
GND J158
BC601 R618
R6 C635
2
R690
J161
R611
D663 R604
L602
R688 R673
D604
J144 R670 D405
R689 D656 C602 R602
JS605
JS606
AMP+13V D653
R679 R683 R671
C656
D406 D658
Q658
05
R672 R663 +B JS603
C6
R685 J145 RESET Q650 R693
D601
C665 R691 D657 +B JS604
R686 J143
R678 R682 R664
C633 P-ON+21V R692 C616
Q656 R652 BC603
R687 R684
C636 D654
D662
R653
Q657
R665 Q659
Q657A
D603
C664 R662 R680 C639
ALL+3.3V
C662
LED-CONT
R681 C657
Q658A
J150
J151
J168
GP002 D664
ALL+3.3V C638
J147
IC651
J152
GND
C663 SA602
ALL+3.3V
22 2 D602
C661 C632
J153
BC602
GND
J146
GND
GT601
1
23
A B C631 CN501
C D
10-28 BA31M0F01024
Power Supply CBA Top View [TYPE D, TYPE E]
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
CAUTION !
when troubleshooting this type of power supply circuit,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, a variable isolation transformer is required.
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail. NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
C617
BA31FCF0102 3
J163
J141
GND
/BLACK
FH602 FH601
LIVE
J169
T 2.5A L/250V
F602
/WHITE
CN601
BC1001
F601 GND D652
C1005
NEUTRAL BC1002
4A/125V P-ON+21V
C1001
J154
D660
J139
GND
J140
R601 P-ON+21V
IC601
RISK OF FIRE- AMP+13V J136 GP001
R1
SA601 IC602
02
REPLACE FUSE AS MARKED P-ON-H2+ J138
C1006
0
1
CO
2
C653
J171
J133
FG
FG
CN1001
LD
C650
03 D651
L1001
C6
7
C652
C604
HO
6
T601
T
50
J159
D6
JS601
JS602
C1018
C651
BL-ADJ
C606
J149
J142
D608
L601
GATE
P-ON+21V
FG
J135
C611 C654
J137
J148
+13V
+13V
J134
+13V
J155
LED+21V
C614
J162 GND
J167
BC604
GND
PROTECT3
C655
BL-ADJ
BL-SW
R6
J157
J160
J158 GND
D607 BC601 D655 76
2
J161
R611
L602
D604
J144
R602 C602
JS605
JS606
C656
Q658
C6
JS603 +B
05
RESET J145
D601
JS604 +B J143
R678
C616 P-ON+21V
BC603
D662
Q657
D654
D603
ALL+3.3V
LED-CONT
C662
J150
J151
J168
GP002
ALL+3.3V
J147
No.2
J152
GND
SA602 C663
ALL+3.3V
D602 2 22
J153
BC602
J146
GND
GND
GT601
1
23
D C CN501
B A
10-29 BA31FCF01023
Power Supply CBA Bottom View [TYPE D, TYPE E]
Because a hot chassis ground is present in the power supply
circuit, an isolation transformer must be used when repairing.
Also, in order to have the ability to increase the input slowly,
CAUTION !
when troubleshooting this type of power supply circuit,
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, a variable isolation transformer is required.
If Main Fuse (F602) is blown , check to see that all components in the power supply replace only with same type 2.5A, 250V fuse.
circuit are not defective before you connect the AC plug to the AC power supply. 2.5A 250V ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.
Otherwise it may cause some components in the power supply circuit to fail. NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
BA31FCF0102 3 C617
J163
J141
GND
R657 FH601 FH602
J169
BC1001 R659
CN601
D652 R660 GND F601
C1005
BC1002
F602
4A/125V
GND
C1001
R675
T 2.5A L/250V
J154
J139
D660
GND
J140 D661
GND J170
C1002 P-ON+21V R674
Q653 R601
GP001 C1003 IC601
02
0 C1004 J136 AMP+13V R667 C666 R661 IC602 SA601
J138 P-ON-H2+ R658
R1
C1009
C1006
R669 C660
1
C610
2
J171
D652A
FG
C1008 R654 FG
6 CN1001
Q621
R1022 C652
C604
R622
R1017
C1015 L1002 R1021 C621
T601 D621 R608
R1011 IC1001 D650A R621 C608 Q602
D6
50
J159
JS601
C609
JS602
C1018 D605 R606
R1012 R607 C607
R1013 R612
C651 R609
BL-ADJ
J149
C1016 J142
D608
L601
R1014 C1012
GATE
D1002
P-ON+21V
R1015 C1013 FG
J135
R1008 C654
C1011 C611
J137
R1016
J148
+13V
+13V
R1001
J134
D608A
+13V
R1009
R1005 R1002 J155
R1006
D654A
R1007 C1014 LED+21V C1010 R615
C614
R1010
R1004 R617
R1003
GND J162 R616
Q601
BC604
J167
GND
C655 D653A
PROTECT3
BL-ADJ
R677
J157
J160
76
GND J158
BC601 R618
R6 C635
2
R690
J161
R611
D663 R604
L602
R688 R673
D604
R670 D405 J144
R689 D656 C602 R602
JS605
JS606
AMP+13V D653
R679 R683 R671
C656
D406 D658
Q658
05
R672 R663 +B JS603
C6
R685 J145 RESET Q650 R693
D601
C665 R691 D657 +B JS604
R686 J143
R678 R682 R664
C633 P-ON+21V R692 C616
Q656 R652 BC603
R687 R684
C636 D654
D662
R653
Q657
R665 Q659
Q657A
D603
C664 R662 R680 C639
ALL+3.3V
C662
LED-CONT
R681
Q658A
J150
J151
J168
GP002 D664
ALL+3.3V C638
J147
IC651
J152
GND
C663 SA602
ALL+3.3V
22 2 D602
C661 C632
J153
BC602
GND
GND
J146
GT601
1
23
A B C631 CN501
C D
10-30 BA31FCF01023
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE A]
CL3801
1 4
TUNER UNIT CN3101 CN4001
CN3801
1 9
CL3101
FUNCTION CBA UNIT
COMPONENT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
REAR B W
AUDIO(L)-IN
CN601
AUDIO(R)-IN
CN3701 CN501
11-1
DIGITAL
AUDIO-OUT 1 23
(COAXIAL) CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
23 1
HDMI-
CONNECTOR-1
WIRING DIAGRAM
HDMI-
CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3013
1
CL3006
USB JACK
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9AWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE B]
CL3801
1 4
TUNER UNIT CN3105 CN4001
CN3801
1 9
CL3101
COMPONENT FUNCTION CBA UNIT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN B W
REAR CN601
AUDIO(R)-IN
DIGITAL
AUDIO-OUT CN3601 CN501
11-2
(COAXIAL) 1 23
CL3701
DIGITAL MAIN CBA UNIT
ETHERNET POWER SUPPLY CBA
23 1
JACK
HDMI-
CONNECTOR-1
HDMI- CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3905
1
CL3006
USB JACK WIRELESS
LAN MODULE
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9BWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE C]
CL3801
1 4
TUNER UNIT CN3101 CN4052
CN3801
1 9
CL3101
FUNCTION CBA UNIT
COMPONENT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
REAR B W
AUDIO(L)-IN
CN601
AUDIO(R)-IN
CN3701 CN501
11-3
DIGITAL
AUDIO-OUT 1 23
(COAXIAL) CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
23 1
HDMI-
CONNECTOR-1
HDMI-
CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3013
1
CL3006
USB JACK
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9CWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE D]
CL3801
1 4
TUNER UNIT CN3101 CN4052
CN3801
1 9
CL3101
FUNCTION CBA UNIT
COMPONENT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
REAR B W
AUDIO(L)-IN
CN601
AUDIO(R)-IN
CN3701 CN501
11-4
DIGITAL
AUDIO-OUT 1 23
(COAXIAL) CL3701
DIGITAL MAIN CBA UNIT POWER SUPPLY CBA
23 1
HDMI-
CONNECTOR-1
HDMI-
CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3006
1
CL3006
USB JACK
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9DWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE E]
CL3801
1 4
TUNER UNIT CN3105 CN4052
CN3801
1 9
CL3101
COMPONENT FUNCTION CBA UNIT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN B W
REAR CN601
AUDIO(R)-IN
DIGITAL
AUDIO-OUT CN3601 CN501
11-5
(COAXIAL) 1 23
CL3701
DIGITAL MAIN CBA UNIT
ETHERNET POWER SUPPLY CBA
23 1
JACK
HDMI-
CONNECTOR-1
HDMI- CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3904
1
CL3006
USB JACK WIRELESS
LAN MODULE
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9EWI
SP3801 SP3802
SPEAKER SPEAKER
L-CH R-CH
[TYPE F]
CL3801
1 4
TUNER UNIT CN3105 CN4052
CN3801
1 9
CL3101
COMPONENT FUNCTION CBA UNIT
-Y/VIDEO-IN
9 1
AC CORD
COMPONENT
-Pb-IN
COMPONENT
-Pr-IN
AUDIO(L)-IN B W
REAR CN601
AUDIO(R)-IN
DIGITAL
AUDIO-OUT CN3601 CN501
11-6
(COAXIAL) 1 23
CL3701
DIGITAL MAIN CBA UNIT
ETHERNET POWER SUPPLY CBA
23 1
JACK
HDMI-
CONNECTOR-1
HDMI- CN1001
CONNECTOR-2
1 7
HDMI-
CONNECTOR-3
SIDE PC-RGB-IN
CN3905
1
CL3006
USB JACK WIRELESS
LAN MODULE
LCD PANEL ASSEMBLY
30
HEADPHONE
JACK
PL13.9FWI
EXPLODED VIEWS
[TYPE A]
A1
LCD1
L7
A4
A16
A13
CL3006
A5
A17 B12
S7 Digital Main CBA Unit
B18
CL3701 B18
[32PFL4508/F7(Serial No.:ME1)] B17
GP002 B17
L7
Function CBA Unit A3
GP001
L7 L23 L27
L23
A20 SP3801
CL3801
AC601 CL3101
L23
Power Supply CBA
SP3802 L7
L45
A15
A11
SSK1
S7 SBA1
A1
LCD1
L7
A4
A16
A13
CL3006
A5
L45
L7
See Electrical Parts List X6
for parts with this mark.
A15
A11
SSK1
S7 SBA1
A1
LCD1
L7
A4
A16
A13
CL3006
S7
Digital Main CBA Unit
B18
CL3701 B18
B17
A6 B12 B17
A9 L7
A3
L23
SP3801 L23 L27
L7
Function CBA Unit CL3801
AC601 L23
CL3101
L45
A15
SA1
S7
SSK1
A1
LCD1
L7
A4
A16
A13
CL3006
S7
Digital Main CBA Unit
B18
CL3701 B18
B17
A6 B12 B17
A9 L7
A3
L23
AC601 L23
CL3101
L45
A15
SA1
S7
SSK1
SSK1
A11 X2
X3
X4
S7 Tape
S3
S3
X1
SBA1
Packing Tape
S6
S4
S1
Packing Tape
S7
FRO FRO
NT S12 NT
12-5 PL13.9PEX
[TYPE C, D, E, F]
SSK1
X2
X3
X4
S7 Tape
S3
S3 X1
SA1
Packing Tape
S6
S4
S1 Packing Tape
S7
FRO FRO
NT S12 NT
12-6 PL13.9PEX
TYPE A
PARTS LIST [32PFL4508/F7 (Serial No.: ME1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a LCD PANEL ASSEMBLY
# have special characteristics important to safety.
Ref. No. Description Part No.
Before replacing any of these components, read
LCD1# LCD PANEL ASSEMBLY U3FF1PA
carefully the product safety notice in this service
Consists of the following
manual. Don't degrade the safety of the product
A1 FRONT CABINET A31F2UT 1EM030385
through improper servicing.
A4 X-PCB COVER A31F0UT 1EM030745A
NOTE: Parts that are not assigned part numbers A5 DECORATION PLATE A31M2UT 1EM228002
DIGITAL MAIN CBA UNIT C661 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C665 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
Ref. No. Description Part No. C666 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
DIGITAL MAIN CBA UNIT A31F2MMA-001 C1001 CAP ELE 330µF/25V/M/85 CED3310V8006
IC3001 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021 C1002 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048 C1003 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
IC3003 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021 C1005 CAP ELE 47µF/100V/M/85 CEH4700V8006
IC3004 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233 C1006 CAP ELE 47µF/100V/M/85 CEH4700V8006
IC3005 IC DTV-C7V R8A05011BG-U0/256FHP QSAA0R0HT057 C1007 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
IC3006 IC 32M-BIT SERIAL FLASH MEMORY NSCA0R0ZM018 C1008 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
W25Q32FVSSIG
C1009 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
IC3007 IC LDO REGULATOR BD00IC0WEFJ/HTSOP-J8 QSCA0T0RM397
C1011 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
IC3008 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
C1012 CHIP CERAMIC CAP.(1608) B K 4.7µF/6.3V CHD0KK30B475
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
C1013 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
IC3011 IC EEPROM BU9883FV-WE2 QSCA0T0RM105
C1014 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
IC3013 IC SINGLE BUS BUFFER 74LVC1G126GW NSCA0TNXP004
C1017 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
IC3014 IC SINGLE BUS BUFFER 74LVC1G126GW NSCA0TNXP004
CONNECTORS
IC3018 IC HDMI SW TMDS351PAGR /PAG-64 NSCA0T0TY068
CN501 FPC/FFC CONNECTOR IMSA-9615S-23C-PP-A JC96J23ER009
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/ NSCA0TDES015
5PI CN601# CONNECTOR S2P3-VH (LF)(SN) JCVHC02JG002
IC3601 IC REGULATOR AP2121AK-3.3TRE1 NSCA0TBCD026 CN1001 FPC/FFC CONNECTOR IMSA-9615S-07A-PP-A JC96J07ER007
IC3621 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021 DIODES
IC3801 IC D-CLASS AUDIO POWER AMPLIFI NSCA0T0TY073 D601 DIODE 1N5397BD NDL1001N5397
TPA3110D2PWPR D602 DIODE 1N5397BD NDL1001N5397
IC3851 IC HEADPHONE AMP BH3547F SOP 8PIN QSZBA0TRM119 D603 DIODE 1N5397BD NDL1001N5397
TU3901 TUNER UNIT U9001UT U9001UT D604 DIODE 1N5397BD NDL1001N5397
D605 ZENER DIODE MM5Z4V3B ND1BMM5Z4V3B
FUNCTION CBA UNIT D607A# ZENER DIODE SMD TFZVTR27B QD1B00TFZV27
D608# DIODE ZENER 1ZB36BB NDWZ0001ZB36
Ref. No. Description Part No. D609A DIODE SCHOTTKY SMD CES520.L3F(D QD1Z00CES520
FUNCTION CBA UNIT A31F2MSW-002 D610 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
IC4001 IC TOUCHSENSOR MICON NON-AUTOT NSCA0T0TY080 D621 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
CY8C20324-12LQXIT/CP
D623 ZENER DIODE MM5Z30B ND1B0MM5Z30B
D650 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
POWER SUPPLY CBA D651 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D653 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0
Ref. No. Description Part No.
D654# DIODE ZENER 1ZB20BB NDWZ0001ZB20
POWER SUPPLY CBA A31F2MPW-001 D655 DIODE SCHOTTKY SB3A0BH NDWZ000SB3A0
Consists fo the following
D656 DIODE FAST RECOVERY RS1BJTD ND1Z0RS1BJTD
CAPACITORS
D657 ZENER DIODE MM5Z11B ND1B0MM5Z11B
C602# SAFTY CAP. 1000pF/250V KX CA2E102MR101
D660 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
C603# SAFTY CAP. 1000pF/250V KX CA2E102MR101
G.....±2% J......±5% K.....±10% R690# RES CHIP 1608 1/10W J 1.5 Ω RRXA1R5HH013
GP001 Not used
M.....±20% N.....±30% Z.....+80/-20% GP002 Not used
Chassis PL13.9
• 2013/1/29 32PFL4508/F7 (Serial No.: ME1) Added
• 2013/3/19 32PFL4908/F7 (Serial No.: ME1) Added
• 2013/4/1 32PFL4508/F8 (Serial No.: XA1) Added
• 2013/4/25 32PFL4508/F8 (Serial No.: XA2) Added
• 2013/6/21 32PFL4908/F8 (Serial No.: XA1) Added
• 2013/7/31 32PFL4508/F8 (Serial No.: VM1) Added
• 2013/8/19 32PFL2508/F8 (Serial No.: VM1) Added
• 2013/9/12 32PFL2508/F8 (Serial No.: VM3) Added
• 2013/9/12 32PFL2908/F8 (Serial No.: VM1) Added
• 2013/10/1 32PFL2908/F8 (Serial No.: VM2) Added
• 2013/12/18 32PFL4908/F7 (Serial No.: ME2) Added
14-1 PL13.9REV
COMPARISON LIST OF MODEL NAMES
Chassis PL13.9
32PFL4508/F7 (ME1) A31F2UT TYPE A
PL13.9COM