Beruflich Dokumente
Kultur Dokumente
1
◎ Supplement Harness (15901501)
Harness that is required if upgrading from the e-manage (blue) to e-manage Ultimate.
Connector 1 and 2 are the same for e-manage and e-manage Ultimate. The e-manage
Ultimate has a third connector which is this supplement harness.
2
◎ A/F Sensor Harness (15900912)
Used to connect a wide band O2 sensor 0-5 volt analog signal to the e-manage “Option” port.
Used for data logging air fuel ratio while tuning with Support Tool.
◎ Adapters
※ Ignition Adapters
※ Ignition Adapters 1~3 can be placed inside the hardware.
3
※ Injector Adapters
4. Injector Adapter 1 (15901505)
Used t o prevent a check engine light when wiring the injector harness as add/subtract fuel
on four c ylinder mot ors onl y (Newer Mitsubish and Subaru).
5. Injector Adapter 2 (15901504) (included in units with serial number 4000 ~on)
Used t o prevent extremel y rich conditions when wiring the injectors harness as
add/subtract fuel.
4
8. O2 Sensor Adapter (15900908)
Used t o send a l ean O2 si gnal to the ECU, when the ECU is operating i n cl osed loop.
Designed for vehi cles that have a narrow band (0-1V) O2 sensor.
5
e-manage Ultimate Wiring and Setup
● Wiring Diagram
1. e-manage Ultimate Pin Diagram
Connectors A and B are the same as the e-manage. The e-manage Ultimate has added
Connector C for more functions.
6
2. Injector Wiring
The e-manage Ultimate has up graded the inject or adj ustment feature. Now the injector pulse
wi dt h can be shortened b y the e-manage Ultimate i ntercepting the Injector pulse si gnal. Als o
group injection s ystems can be converted t o seq uential i nj ection.
※ Can be wired as add only (same as e-manage) or add/subtract fuel.
※ Diagram below is for add/subtract fuel.
7
3. Sub Injector Wiring
Now the e-manage Ultimate can control up to 8 sub i nj ect ors.
4. Ignition Harness
Used t o adjust ignition timi ng b y intercepting ECU ignition p ulse.
The e-manage Ulti mate can also convert distributor type i gnition systems and waste spark
ignition systems to direct igniti on s ystem.
※ Diagram below is for normal i gnition control
● Connect ignition channels i n order of engine firing order.
8
※ Diagram Below is for converting t he ignition system.
※ Crank and Cam Positi on Sensors need to b e recognized b y e-manage Ulti mate to operate.
9
5. Idle Control
Designed for vehi cle that have rough idle due to removi ng the airflow meter or turning on the
A/C. Can onl y be used wit h solenoid t ype Idle Control Valves.
※ Must set jumper 16 t o OPEN.
10
7. Vehicle Speed Sensor
Intercept vehicle speed signal for vehicle speed adjust ment map or remove speed limiter.
Can also wire inp ut signal onl y for data logging purpose.
11
9. Knock, Water Temp, Intake Temp Signal
Two channels are used to monitor factor y knock sensor, coolant temperat ure sensor, or intake
temperature sensor.
12
● Hardware Setup
1. Jumper Setting
Used to adj ust the circuits on t he e-manage hardware to match t he prop er application.
Remove the hardware from the case to adjust Jumpers.
※ When using Inject or Channels 1-6 for sub i njector or NVCS, set the used channel to OPEN.
13
● Connecting the Unit to a Laptop Computer
◎ Requires the use of the e-manage Ultimate Software
◎ Connection between e-manage Ultimate Unit and Laptop by USB.
USB Cable
※The latest versions of the e-manage Ultimate Software and firmware is 2.12 (just released).
If your versions are older than this, please download the update from our website.
The 8 adjustment cells are now upgraded to 16 cells, for even finer adjustment.
14
Injection Adjustment Map (1 and 2)
Fuel trimming in the previous system was achieved by adjusting the ''Airflow Adjustment Map''
which could also affect the ignition timing. The improved ''Injection Adjustment Map'' is used to
trim and add fuel directly by controlling the injector signal, therefor it will not affect the ignition
timing at all. (However with an internal jumper setting change, the system is still able to trim the
fuel by adjusting the airflow signal like the previous unit)
Individual Cylinder Injection Adj. & Individual Cylinder Ignition Adj. Maps
It is possible to correct uneven combustion between cylinders, by fine tuning each individual
cylinder for more advanced tuning.
When the ECU Intake Air Temp Calibration does not match the e-manage's tuning, this map is
used to tune the system at various temperature ranges.
(#)This map is also be used when eliminating the airflow meter on a vehicle equipped with a
hotwire type airflow meter.
15
Rev Limiter Cut
For vehicles with a fuel cutting controlled rev limiter, this feature will drive the injectors past the
factory rev limiter.
*This feature will not work on vehicles with rev limiter controlled by ignition cut.
If the factory idle control valve is a solenoid type valve, this map can vary the valve's duration to
adjust the injection rate.
(#)This is used when eliminating the airflow meter.
16
(Dip) Toggle Switch
4 different maps can be activated and de-activated using the dip switches on the front of the unit.
Protect Feature
Each Map has the option to be password protected.
Serial port
External data (like ''GReddy Warning Meters'', and other future optional products) can be
monitored and recorded in real time through a data link cable.
Switch Port
''Data logging''and''Ignition Cut'' features can be activated with the use of an optional ''Remote
Switching System'' and
''Switching Harness''
17
GReddy e-manage Ultimate Version Update Information
Version 2.00
≪ Advanced Functions ≫
∙ Addition of water temperature dependant ignition adjustment setting.
∙ Addition of intake temperature dependant ignition adjustment setting.
∙ Addition of data sampling Map.
≪ Additional Functions ≫
∙ Multiplying RPM signal by 1/2, 1/3, 1/4 and 1/6 to display proper value.
∙ Addition of “Universal” engine type.
∙ Water temperature setting for Anti Engine Stall Map.
∙ Capability to display absolute pressure value using OEM pressure sensor when connected to analog input.
∙ Data logging knock level.
∙ Fuel pump relay control under I/J tab.
∙ More Maps to select from using the front panel dip switch control.
∙ More A/F sensor manufactures added to front panel OPTION 1,2 settings.
∙ Use of front panel switch port to switch between Maps.
∙ Add paste function for Maps.
∙ Automatic split window adjustment between Ultimate and data logger windows.
∙ Parameter setting print function.
∙ Logger trace with B cursor.
∙ Logger trace line movement with the left and right keys.
∙ Creating RPM based logger text file.
≪ Functional Correction ≫
∙ Icons created for setting and logger files.
∙ Open setting or logger files by double-clicking file.
∙ Improvement of engine starting.
∙ Acceleration Injection Map control.
∙ Acceleration Ignition Map control.
∙ Rev limiter cut control setting.
∙ Acceleration injection Map adjustment increments
∙ Acceleration ignition Map adjustment increments.
∙ Parameter setting adjustment increments.
∙ Security function for each map.
∙ Injector lag time adjustment increments
∙ Print screen for Data Logger
∙ Data Logging capabilities for rotary engines.
18
v-manage – Variable Valve Timi ng M anager
The v-manage unit is designed t o adjust valve t iming on variable valve timi ng s ystems. Systems t hat are
adjustable include:
Toyota: VVT-i, VVTL-i, Dual VVT-i
Honda: i-VTEC
Subaru: AVCS
Nissan: CVTC
Mit ubishi: MIVEC
19
Connecting to the Unit
The v-manage unit can communicate directly to the PC using a USB cable or can connect to the PC
through the e-manage Ultimate using the serial port.
When connecting to the e-manage Ultimate, the Front Panel Serial setting must be set to v-manage for
the PC to communicate with both the v-manage and e-manage Ultimate simultaneously.
20
Benefit from using v-manage
By using the v-manage you will be able to broaden the torque and horsepower band. Since factory
ECUs must comply with emission standards, lower RPM range valve timing is not optimal. The
v-manage unit will take full control of the valve timing system and allow you to bring out the full
potential of the engine.
21