Sie sind auf Seite 1von 1

ASME B16.

5-2013

(Fig. II-13 of Mandatory Appendix II), and the height 7.3 Facings (13)
shall provide lengths as specified in Fig. 11 or 12 Tolerances that apply to both flange and flanged fit-
(Fig. II-11 or II-12 of Mandatory Appendix II). ting facings are as follows:
6.12.6 Size. Unless otherwise specified, auxiliary (a) Inside and outside diameter of large and small
connections shall be of the pipe sizes given below. tongue and groove and female, ±0.5 mm (±0.02 in.).
(b) Outside diameter, 2.0 mm (0.06 in.) raised face,
Connection
±1.0 mm (±0.03 in.).
Fitting Size Size (NPS)
(c) Outside diameter, 7.0 mm (0.25 in.) raised face,
1
2 ≤ NPS ≤ 4 ⁄2 ±0.5 mm (±0.02 in.).
3
5 ≤ NPS ≤ 8 ⁄4 (d) Ring joint groove tolerances are shown in Table 5
NPS ≥ 10 1
(Table II-5 of Mandatory Appendix II).
6.12.7 Designating Locations. The designation of Tolerances that apply to flanges are as follows:
locations for auxiliary connections for flanged fittings (e) Perpendicularity of the face with the bore
is shown in Fig. 15. A letter is used to designate each Size Tolerance
location.
NPS ≤ 5 1 deg
NPS ≥ 6 0.5 deg
7 TOLERANCES
7.4 Flange Thickness (13)
7.1 General Required tolerances for flange thickness are as follows:
For the purpose of determining conformance with Size Tolerance
this Standard, the convention for fixing significant digits
NPS ≤ 18 +3.0, −0.0 mm (+0.12, −0.00 in.)
where limits, maximum or minimum values, are speci-
NPS ≥ 20 +5.0, −0.0 mm (+0.19, −0.00 in.)
fied shall be rounded as defined in ASTM Practice E 29.
This requires that an observed or calculated value shall The plus tolerance is applicable to bolting bearing
be rounded to the nearest unit in the last right-hand surfaces whether as-forged, as-cast, spot-faced, or back-
digit used for expressing the limit. The listing of decimal faced (see para. 6.6).
tolerances does not imply a particular method of
measurement. 7.5 Welding End Flange Ends and Hubs
7.5.1 Outside Diameter. Required tolerances for the
7.2 Center-to-Contact Surfaces and Center-to-End nominal outside diameter dimension A of Figs. 7 and 8
Tolerances (Figs. II-7 and II-8 of Mandatory Appendix II) of welding
Required tolerances for various flanges and flanged ends of welding neck flanges are as follows:
fitting elements are as follows: Size Tolerance
(a) Center-to-Contact Surfaces Other Than Ring Joint
NPS ≤ 5 +2.0, −1.0 mm (+0.09, −0.03 in.)
Size Tolerance NPS ≥ 6 +4.0, −1.0 mm (+0.16, −0.03 in.)

NPS ≤ 10 ±1.0 mm (±0.03 in.) 7.5.2 Inside Diameter. Required tolerances for the
NPS ≥ 12 ±1.5 mm (±0.06 in.) nominal inside diameter of welding ends of welding
neck flanges and smaller bore of socket welding flanges
(b) Center-to-End (Ring Joint)
(dimension B in the referenced figures) are as follows:
Size Tolerance (a) For Figs. 7 and 8 (Figs. II-7 and II-8 of Mandatory
NPS ≤ 10 ±1.0 mm (±0.03 in.) Appendix II) and Fig. 4, the tolerances are
NPS ≥ 12 ±1.5 mm (±0.06 in.) Size Tolerance

(c) Contact Surface-to-Contact Surface Other Than Ring NPS ≤ 10 ±1.0 mm (±0.03 in.)
Joint 12 ≤ NPS ≤ 18 ±1.5 mm (±0.06 in.)
NPS ≥ 20 +3.0, −1.5 mm (+0.12, −0.06 in.)
Size Tolerance
(b) For Fig. 9 (Fig. II-9 of Mandatory Appendix II),
NPS ≤ 10 ±2.0 mm (±0.06 in.) the tolerances are
NPS ≥ 12 ±3.0 mm (±0.12 in.)
Size Tolerance
(d) End-to-End (Ring Joint)
NPS ≤ 10 +0.0, −1.0 mm (+0.0, −0.03 in.)
Size Tolerance NPS ≥ 12 +0.0, −1.5 mm (+0.0, −0.06 in.)

NPS ≤ 10 ±2.0 mm (±0.06 in.) 7.5.3 Backing Ring Contact Surface. Required toler-
NPS ≥ 12 ±3.0 mm (±0.12 in.) ances for the bore of the backing ring contact surface of

13
c
       
                                        

                                                              


Das könnte Ihnen auch gefallen