Beruflich Dokumente
Kultur Dokumente
Steel
Model 3LS
Pumps 316 S/S Centrifugal Pumps (2 pole)
To DIN 24255
Specifications
˜ End suction centrifugal pump with closed impeller
˜ Maximum working pressure: 10 bar
˜ Liquid temperature: -10 °C to +110 °C
Materials
˜ Pump casing: 316 Stainless Steel
˜ Impeller: 316 Stainless Steel
˜ Casing cover: 316 Stainless Steel
˜ Shaft: 316 Stainless Steel (wetted part)
˜ Motor bracket: Cast Iron
˜ Mechanical seal: SiC/SiC/Viton
Motor Data
˜ IEC standard 2 pole 50 Hz motors
˜ Normally fitted with WEG motors
˜ 3 Phase, TEFC, IP55 or above, Class F or above
Range
˜ 32 to 80 mm Ø discharge
Stub shaft design ˜ 1.1 to 55 kW - 3 Phase
30
65 mm
distortion from pipe loads. 50 mm
20
mm
40
mm
Available as pump end kit tor 32
Mo mm
ard
10
(without motor)
d 1.1
S tan kW
IEC
5
100 200 300 500 700 1000 2000 3000 5000
Standard IEC Capacity - lpm
4000 lpm
motors used,
allowing for —Over 40 model sizes
single phase,
Motor special —32 mm to 80 mm discharge
Supports
Stub enclosure, or
Shaft
Motor Kit specific brand —1.1 to 55 kW motor power
nd s
Bracket
m p E ener motors to be
u st
Pump e P fa
let all fitted. —Flows to 4000 lpm
End
o mp ding
C clu
in
—Heads to 90 metres
Page 1/4
Performance Curves Model MATRIX
Model 3LS
100
90 3LS
80 2 Pole
80 65-25 -25
0/37
0/5
70 65-2 5
40-20 50/3 80
32-200/5 0/11 50-2 0
60 .5 00/1 -2
5 50
32 65- /4
200 80
50 32-200
-2
00 40-2 50- /22 -20 5
/4.0 /7. 00/7 200 65 80 0/3
5 .5 /11 -20
50 65 0/1 -2 7
-20 -20 8.5 00
40 0/9 0/1 80 /3
32-20 40- .2 -2 0
0/3.0 200 5 00
/5.5 65 /
32-16 40- 50 -1 80 22
0/2.2 160 -16 60 -1
30 /4.0 0/7 65 /1 60
/1
.5 -1 5 8.
60
Total Head - m
80 5
32-1 /1 -1
50 1 60
65 65-
60/1 40 -1
.5 -16 /1
-1
60 5
60
0/3 /5
40 50 .5
/9
20 .0
.2
32-1 -1 -1
12
25 25
80
25/1 /2
5/
.1 /4
-16
.2 .0
7.
5
0/1
65
-1
1
25
50
40
/5.
-1
-1
25
5
25
65
/3.
50
/1
-12
.5
0
-12
10
5/4
5/2
9
.0
.2
8
7
6
5
100 200 300 500 700 1000 2000 3000 4000
Capacity - lpm
3LS pumps use IEC standard motors. 3 phase WEG cast iron motors are generally fitted as standard, but single phase,
specific brands, special enclosures, etc. can also be supplied. The requirements for frame size and mounting are in the
dimension table. Note that B5 = Flange mount; B35 = Foot & Flange mount.
The style of motor support varies depending on model and motor size, as shown in the figures below and referred to in the
dimension table.
Fig 3 Fig 4
Fig 1 Fig 2
Fig 6 Fig 7
Fig 5
Page 2/4
Dimensions - with cast iron W22 WEG motors (E3) Model MATRIX
Model 3LS
H
DN1
X
Recommended
H1 space for
disassembly
4 x 18Ø 8 x 18Ø
DN 32 40 50 65 80 100
Flanges P 75 80 95 115 120 135
32,40,50 DN 80 & DN K
to DIN 2532 P D P D K 100 110 125 145 160 180
K
& 65 Ø mm 100 Ø mm
D 140 150 165 185 200 225
Page 3/4
Construction Model 3LS
Typical with stamped casing
A (i.e. all 32, 40 & 50 mm & 65 -125/160/200)
4
26
11
7
Data Sheet
EBARA PUMPS AUSTRALIA PTY. LTD.
Page 4/4 3LS 13-03