Beruflich Dokumente
Kultur Dokumente
SPECIFICATIONS
AND TECHNICAL DATA
Standard Pre-cut Anchor Rods and
Extended Anchor Rod Program
As global leaders in chemical anchoring systems, Hilti has provided threaded rod for anchoring
applications in materials such as concrete and masonry for many years.
As your partner, we offer a broad portfolio of high quality pre-cut Hilti anchor rods that in
conjunction with the Hilti injectable mortars and adhesive capsules provide reliable and high
performing fastening points, and enable the installer to complete chemical anchoring applications
efficiently, hassle-free, without compromising the budget.
Hilti HIT-Z Anchor rod Hilti HAS Threaded rod Hilti HIT-V Threaded rod
(SafeSet™) Broad portfolio including high-strength, Reliable Hilti quality to fulfill the
For use with Hilti HIT-HY 200 Injectable hot-dipped galvanized, and stainless basic needs of chemical anchoring
mortar, the Hilti HIT-Z Anchor rod steel for the demand of increased applications in conjunction with
provides the ultimate in safety and load performance and usability with capsule injectable adhesive systems
capacity combined with up to 60% systems
faster installation due to zero-cleaning
SafeSet™ Technology*
The following technical data is for standard length threaded rods as shown on page 9, and for HIT-Z anchor rods. For new custom length and larger diameter threaded
rod and large diameter options see page 10.
Specifications and physical properties of Hilti HIT-V, HAS, and HIT-Z threaded rods with standard lengths
Minimum
Minimum
Specified
Specified Yield Elongation, Min. Reduction of Specification for
Threaded Rod Specification Units Ultimate futa / fya
Strength 0.2% %9 Area, Min. % Nuts and Washers
Strength,
Offset, fya
futa
HAS-E-B HDG psi 125,000 (7) 105,000 16 (B7) 50 (B7) Nuts: ASTM A 194, Grade 2H,
ASTM A 193, Grade B7 6,11 Heavy, or ASTM A563-15 Grade C
1.19
ASTM F 1554 Grade 10511,12,13 Washers: ASTM F436 Type 1 and
(MPa) (862) (7) (724) 15 (Gr. 105) 45 (Gr. 105)
ANSI B18.22.1 Type A Plain
HIT-Z Anchor rod psi 94,200 75,300 Nuts: ASTM A 563 Grade A
(HIT-HY 200 only)
1.25 8 20 Washers: ASTM F844, HV and
Unalloyed carbon steel 10
(MPa) (650) (519) ANSI B18.22.1 Type A Plain
1 Standard Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength
2 ASTM A 307 does not have a minimum specified yield strength. Published yield strength is based on Hilti manufacturer specifications and maximum value of futa / fy = 1.6 as specified in
ACI 318-14 section R17.4.1.2.
3 Hilti HIT-V threaded rods do not meet the minimum elongation requirements for ASTM A 307. HIT-V needs to be considered a brittle steel element.
4 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs
5 HAS-E needs to be considered a brittle steel element.
6 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service
7 For designs according to CSA A23.3-14 Annex D, the maximum value of futa is 860 MPa (124,700 psi) per clause D.6.1.2.
8 Standard Steel Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
9 Based on 2-in. (50 mm) gauge length except for A 193, which are based on a gauge length of 4d and ISO 898-1, which is based on 5d elongation after fracture Af.
10 All carbon steel threaded rods are zinc plated in accordance with ASTM F1941 Fe/Zn 5 AN, with nuts and washers zinc plated in accordance with ASTM B633 SC 1 Type III.
11 HAS-E-B HDG rods hot-dip galvanized in accordance with ASTM A 153.
12 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
13 3/8-inch dia. threaded rods are not included in the ASTM F1554 standard. Hilti 3/8-inch dia. HAS-E-B (incl. HDG) threaded rods meet the chemical composition and mechanical property
requirements of ASTM F1554.
DBS • 02/18
2
Hilti Anchor Rod Specifications and Technical Data
The following steel design information is for Hilti standard threaded rod lengths and HIT-Z anchor rods according to the material specifications on page 2, used in conjunction
with Hilti adhesive anchors designed in accordance with ACI 318 Chapter 17. This includes Hilti HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100, and HIT-ICE.
Steel design information for Hilti HIT-V and HAS threaded rods and Hilti HIT-Z Anchor rods for use with ACI 318 Chapter 17
Nominal Rod Diameter (in.)
Design Information Symbol Units
3/8 1/2 5/8 3/4 7/8 1 1-1/4
in. 0.375 0.5 0.625 0.75 .875 1.0 1.25
Rod O.D. d
(mm) (9.5) (12.7) (15.9) 19.1) (22.2) (25.4) (31.8)
in.2 0.0775 0.1419 0.2260 0.3345 0.4617 0.6057 0.9691
Rod effective cross-sectional area Ase
(mm2) (50) (92) (146) (216) (298) (391) (625)
lb 4,650 8,515 13,560 20,070 - 36,340 -
Nsa
HIT-V ASTM A307
Vsa
(kN) (12.4) (22.7) (36.2) (53.6) - (97.0) -
Reduction factor, seismic shear αv,seis - 0.7
Steel strength reduction factor Φ for tension 3 Φ - 0.65
Steel strength reduction factor Φ for shear 3 Φ - 0.60
lb 5,620 10,290 16,385 24,250 33,475 43,915 70,260
Nsa
(kN) (25.0) (45.8) (72.9) (107.9) (148.9) (195.3) (312.5)
HAS-E ISO 898-1
Vsa
(kN) (15.0) (27.5) (43.7) (64.7) (89.3) (117.2) (187.5)
Reduction factor, seismic shear αv,seis - 0.74
Steel strength reduction factor Φ for tension 3 Φ - 0.65
Steel strength reduction factor Φ for shear 3 Φ - 0.60
lb 9,690 17,740 28,250 41,815 57,715 75,715 121,135
ASTM F 1554 Gr. 1055
Nsa
ASTM A 193 B71 and
Nsa
(kN) (32.5) (59.5) (94.8) (140.0) - - -
(HIT-HY 200 only)
HIT-Z Anchor rod
Vsa
(kN) (20.7) (37.9) (60.3) (75.9) (104.7) (137.4) -
Reduction factor, seismic shear αv,seis - 0.74
Steel strength reduction factor Φ for tension 3
Φ - 0.65
Steel strength reduction factor Φ for shear 3 Φ - 0.60
lb 7,305 13,375 21,305 31,470 - - -
Nsa
HIT-Z-R Anchor rod
C are used, the appropriate value of Φ must be determined in accordance with ACI 318 D.4.4.
4 For HIT-RE 500 V3, the value of αv,seis can be increased. Refer to ICC-ES ESR-3814 or contact Hilti.
5 3/8-inch dia. threaded rods are not included in the ASTM F1554 standard. Hilti 3/8-inch dia. HAS-E-B (incl. HDG) threaded rods meet the chemical composition and mechanical property
requirements of ASTM F1554.
3
STRENGTH DESIGN ACCORDING TO ACI 318 CHAPTER 17 (APPENDIX D)
The following are strength design values calculated from data on the previous page. This is intended for adhesive anchors designed in accordance with ACI 318-14
Chapter 17 (and Appendix D for earlier editions of ACI 318) and can be used in conjunction with the Hilti Simplified Strength Design Tables (refer to Section 3.1.8 of the 2016
and 2017 Hilti Anchor Fastening Technical Guide for more information on the Hilti Simplified Tables). This includes Hilti HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100,
and HIT-ICE.
Steel design strength for carbon steel Hilti HIT-V and HAS threaded rods and Hilti HIT-Z Anchor rods according to ACI 318-14 Chapter
17
Steel design strength for stainless steel Hilti HAS-R threaded rods and stainless steel Hilti
HIT-Z-R Anchor rods according to ACI 318 Appendix D
3 Seismic Shear = αV,seis ΦVsa : Reduction factor for seismic shear only. See ACI 318 for additional information on seismic applications.
Seismic shear for HIT-RE 500 V3 may be increased for HAS-R rods. Refer to ESR-3814.
4 HAS-R Stainless Steel Threaded rods and HIT-Z-R Anchor rods are considered brittle steel elements.
5 Shear value for HIT-Z-R Anchor rod is based on static shear testing with ΦVsa < Φ 0.60 Ase,V futa as noted in ACI 318-14 17.5.1.2b.
4
Hilti Anchor Rod Specifications and Technical Data
The following steel design information is for Hilti standard threaded rod lengths and HIT-Z anchor rods according to the material specifications on page 2, used in conjunction
with Hilti adhesive anchors designed in accordance with CSA A23.3-14 Annex D. This includes Hilti HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100, and HIT-ICE.
Steel design information for Hilti HIT-V and HAS threaded rods and Hilti HIT-Z Anchor rods for use with CSA A23.3-14 Annex D
Nsa
(kN) (20.7) (37.9) (60.3) (89.3) - (161.6) -
Nominal strength as governed by steel strength
lb 2,790 5,110 8,135 12,040 - 21,805 -
Vsa
HIT-V
Nsa
(kN) (25.0) (45.8) (72.9) (107.9) (148.9) (195.3) (312.5)
Nominal strength as governed by steel strength
lb 3,370 6,175 9,830 14,550 20,085 26,350 42,155
Vsa
HAS-E
Nsa
ASTM A 193 B7 and
Nsa
(kN) (32.5) (59.5) (94.8) (140.0) - - -
(HIT-HY 200 only)
HIT-Z Anchor rod
Vsa
(kN) (20.7) (37.9) (60.3) (75.9) (104.7) (137.4) -
Reduction factor, seismic shear αv,seis - 0.74
Steel strength reduction factor R for tension 3 R - 0.70
Steel strength reduction factor R for shear 3 R - 0.65
lb 7,305 13,375 21,305 31,470 - - -
Nsa
HIT-Z-R Anchor rod
5
LIMIT STATES DESIGN ACCORDING TO CSA A23.3-14 ANNEX D
The following are strength design values calculated from data on the previous page. This is intended for adhesive anchors designed in accordance with CSA
A23.3-14 Annex D and can be used in conjunction with the Hilti Simplified Strength Design Tables (refer to Section 3.1.8 of the 2016 and 2017 Hilti Anchor Fastening
Technical Guide for more information on the Hilti Simplified Tables). This includes Hilti HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100, and HIT-ICE.
Steel factored resistance for carbon steel Hilti HIT-V and HAS threaded rods and Hilti HIT-Z Anchor rods according to
CSA A23.3-14 Annex D
Steel factored resistance for stainless steel Hilti HAS-R threaded rods and stainless steel Hilti
HIT-Z-R Anchor rods according to CSA A23.3-14 Annex D
6
Hilti Anchor Rod Specifications and Technical Data
The following technical data is for adhesive anchors that will be designed in accordance with the Allowable Stress Design Method (ASD). This includes Hilti HIT-HY 70 for
masonry, HIT-HY 200 for masonry, HIT-ICE, HIT-HY 10 PLUS, HIT-1, HTE 50 and HVU Capsules.
Note:
• Hilti HIT-V threaded rods are not applicable for use with Hilti HVU Capsules since the end of the rod does not have a chisel point to break and mix the capsules during
installation.
• Hilti HIT-Z Anchor Rods do not have ASD load data since they are only used in conjunction with Hilti HIT-HY 200.
Allowable steel strength for Hilti HIT-V and HAS threaded rods 1
Ultimate steel strength for Hilti HIT-V and HAS threaded rods 1
7
ORDERING INFORMATION
Hilti HIT-Z Anchor rods for Hilti HIT-HY 200 Anchoring system
1/2" x 4-1/2" 20 1/2" x 4-1/2" 20 F R1 “R1” = HAS-R 304 SS R2 “R2” = HAS-R 316 SS
6 1/2 “6 1/2” = Length 6 1/2 “6 1/2” = Length
1/2" x 6-1/2" 20 1/2" x 6-1/2" 20 J
DBS • 02/18
8
Hilti Anchor Rod Specifications and Technical Data
Overview of Hilti HIT-V and HAS standard anchor rod program for Hilti chemical anchoring systems1
HAS-E-B HDG
HIT-V HAS-E HAS-E-B HAS-R 304 HAS-R 316
Hot-dipped galvanized
A307 Steel 5.8 Steel High Str. Steel Stainless Steel Stainless Steel
High Str. Steel
Description Qty Description Qty Description Qty Description Qty Description Qty Description Qty
- - 3/8" x 3" 10 - - - - - - - -
3/8" x 5-1/2" 20 3/8" x 5-1/8" 20 3/8" x 5-1/8" 20 - - 3/8" x 5-1/8" 20 3/8" x 5-1/8" 20
- - 3/8" x 12" 10 - - - - - - - -
- - 1/2" x 3-1/8" 10 - - - - - - - -
1/2" x 6-1/2" 20 1/2" x 6-1/2" 20 1/2" x 6-1/2" 20 - - 1/2" x 6-1/2" 20 1/2" x 6-1/2" 20
1/2" x 8" 10 1/2" x 8" 10 - - 1/2" x 8" 10 1/2" x 8" 10 1/2" x 8" 10
5/8" x 8" 20 5/8" x 8" 20 5/8" x 7-5/8" 20 5/8" x 8" 20 5/8" x 7-5/8" 20 5/8" x 7-5/8" 20
- - 5/8" x 17" 10 - - - - - - - -
3/4" x 10" 10 3/4" x 10" 10 3/4" x 9-5/8" 10 3/4" x 10" 10 3/4" x 9-5/8" 10 3/4" x 9-5/8" 10
- - 3/4" x 21" 10 - - - - - - - -
- - 3/4" x 25" 10 - - - - - - - -
1" x 12" 4 1" x 12" 4 1" x 12" 4 - - 1" x 12" 4 1" x 12" 4
1 Additional diameters and lengths see extended anchor rod program on page 19.
9
EXTENDED HILTI ANCHOR ROD PROGRAM
CUSTOM LENGTHS AND LARGER DIAMETERS
The following technical data is for the extended Hilti anchor rod program where Hilti can supply threaded rods with custom lengths instead of the standard lengths as
shown on page 9. Additionally, threaded rods with a diameter larger than 1-1/4-inch is provided in this extended rod program. Refer to page 19 for the extended rod
portfolio.
Specifications and physical properties of the Hilti Extended Anchor Rod Program
Nuts:
ASTM A194/194M
psi 75,000 95,000 55,000 30 (3/8" - 2")
HAS-E / HAS-E HDG or ASTM A563
1.36 21
ASTM F1554, Grade 55 1,2,8,9
(MPa) (517) (655) (379) 22 (2-1/4" - 2-1/2")
Washers:
HAS-B / HAS-B HDG psi 125,000 (6) 150,000 105,000 16 (B7) 50 (B7) ASTM F436 Type 1
ASTM A193, Grade B7 1,3 1.19
ASTM F1554, Grade 105 1,2,8,9 (MPa) (862) (6) (1,034) (724) 15 (Gr. 105) 45 (Gr. 105)
Nuts:
HAS-R 304 /316 psi 85,000 140,000 45,000
ASTM F594
3/4-in. to 1-in.
1.89 25 -
AISI Type 304 / 316
(MPa) (586) (966) (310) Washers:
ASTM F 593 CW2 4
ASTM A240 Type A
HAS-R 304 /316 psi 75,000 (7) 30,000
1-1/8-in. to 2-in.
NA 2.50 (7) 30 50
ASTM A193 Grade 8(M),
(MPa) (517) (7) (207)
Class 1 3
1 All carbon steel threaded rods are zinc plated in accordance with ASTM F1941 Fe/Zn 5 AN, with nuts and washers zinc plated in accordance with ASTM B633 SC 1 Type III.
All hot-dipped galvanized threaded rods, nuts, and washers are zinc plated in accordance with ASTM F2329.
2 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength.
3 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service.
4 Standard Steel Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs.
5 Maximum specified steel strength according to ASTM standard. NA indicates that ASTM standard does not publish a maximum value.
6 For designs according to CSA A23.3-14 Annex D, the maximum value of futa is 860 MPa (124,700 psi) per clause D.6.1.2.
7 For calculating steel strength, ACI 318-14 section 17.4.1.2 and CSA A23.3-14 clause D.6.1.2 limit the ultimate strength to 1.9 fya.
Thus, futa = 57,000 psi (393 MPa) for calculation purposes when determining steel strength in tension (Nsa) and shear (Vsa).
8 3/8-inch dia. threaded rods are not included in the ASTM F1554 standard. Hilti 3/8-inch dia. HAS-V, HAS-E, and HAS-E-B (incl. HDG) threaded rods meet the chemical composition and mechanical
property requirements of ASTM F1554.
9 Elongation taken from full sized rod per ASTM F1554. Elongation in 2-inch machined specimen is optional.
DBS • 02/18
10
Hilti Anchor Rod Specifications and Technical Data
Vsa
(kN) (12.0) (22.0) (35.0) (51.8) (71.5) (93.8)
Reduction factor, seismic shear αv,seis - 0.6
Strength reduction factor ϕ for tension2 ϕ - 0.75
Strength reduction factor ϕ for shear 2 ϕ - 0.65
lb 5,815 10,645 16,950 25,090 34,630 45,430
ASTM F1554 Gr. 551,4
Nsa
HAS-E / HAS-E HDG
Nsa
ASTM A193 B7 and
Vsa
(kN) (25.9) (47.4) (75.4) (111.6) (154.0) (202.1)
Reduction factor, seismic shear αv,seis - 0.7 (3)
Strength reduction factor ϕ for tension2 ϕ - 0.75
Strength reduction factor ϕ for shear 2 ϕ - 0.65
lb 7,750 14,190 22,600 28,435 39,245 51,485
HAS-R Stainless Steel
Nsa
(kN) (34.5) (63.1) (100.5) (126.5) (174.6) (229.0)
CW Stainless1
DBS • 02/18
11
Steel design information for the Hilti HAS Extended Anchor Rod Program for use with ACI 318 Chapter 17 (Continued)
Vsa
(kN) (118.1) (150.0) (217.5) (294.1) (387.0) - -
Reduction factor, seismic shear αv,seis - 0.6 - -
Strength reduction factor ϕ for tension2 ϕ - 0.75 - -
Strength reduction factor ϕ for shear 2 ϕ - 0.65 - -
lb 57,250 72,685 105,375 142,500 187,500 - -
Nsa
HAS-E / HAS-E HDG
ASTM F1554 Gr. 551
Nsa
ASTM A193 B7 and
Vsa
(kN) (254.7) (323.3) (468.7) (633.9) (834.0) (1,084.2) (1,334.5)
Reduction factor, seismic shear αv,seis - 0.7 (3)
Strength reduction factor ϕ for tension 2
ϕ - 0.75
Strength reduction factor ϕ for shear 2 ϕ - 0.65
lb 43,510 55,240 80,085 108,300 142,500 - -
HAS-R Stainless Steel
ASTM A193, Gr. 8(M),
Nsa
(kN) (193.5) (245.7) (356.2) (481.7) (633.9) - -
Nominal strength as governed by steel strength
lb 26,105 33,145 48,050 64,980 85,500 - -
Class 1 1
Vsa
(kN) (116.1) (147.4) (213.7) (289.0) (380.3) - -
Reduction factor, seismic shear αv,seis - 0.6 - -
Strength reduction factor ϕ for tension2 ϕ - 0.75 - -
Strength reduction factor ϕ for shear 2 ϕ - 0.65 - -
1 Values provided for Hilti threaded rod materials based on published strengths and calculated in accordance with ACI 318-14 Chapter 17 Eq. 17.4.1.2 and Eq. 17.5.1.2b. Nuts and
washers must be appropriate for rod strength.
2 For use with the load combinations of IBC Section 1605.2, ACI 318-14 5.3, or ACI 318-11 D.4.3, as set forth in ACI 318-14 17.3.3 or ACI 318-11 D.4.3. If the load combinations of
ACI 318 Appendix C are used, the appropriate value of ϕ must be determined in accordance with ACI 318 D.4.4.
3 For HIT-RE 500 V3, the value of αv,seis can be increased. Refer to ICC-ES ESR-3814 or contact Hilti.
DBS • 02/18
12
Hilti Anchor Rod Specifications and Technical Data
13
EXTENDED HILTI ANCHOR ROD PROGRAM
LIMIT STATES DESIGN ACCORDING TO CSA A23.3-14 ANNEX D
The following steel design information is for the Hilti extended rod program according to the material specifications on page 10, used in conjunction with Hilti adhesive
anchors designed in accordance with CSA A23.3-14 Annex D. This includes Hilti HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100, and HIT-ICE. Bond strength design
information for threaded rods larger than 1-1/4-inch diameter is currently only available for HIT-RE 500 V3.
Steel design information for the Hilti HAS Extended Anchor Rod Program for use with CSA A23.3-14 Annex D
Vsa
(kN) (12.0) (22.0) (35.0) (51.8) (71.5) (93.8)
Reduction factor, seismic shear αv,seis - 0.6
Strength reduction factor R for tension2 R - 0.80
Strength reduction factor R for shear 2 R - 0.75
lb 5,815 10,645 16,950 25,090 34,630 45,430
ASTM F1554 Gr. 551,4
Nsa
HAS-E / HAS-E HDG
Nsa
ASTM A193 B7 and
Vsa
(kN) (25.8) (47.2) (75.2) (111.3) (153.7) (201.6)
Reduction factor, seismic shear αv,seis - 0.7 (3)
Strength reduction factor R for tension2 R - 0.80
Strength reduction factor R for shear 2 R - 0.75
lb 7,750 14,190 22,600 28,435 39,245 51,485
HAS-R Stainless Steel
Nsa
(kN) (34.5) (63.1) (100.5) (126.5) (174.6) (229.0)
CW Stainless1
DBS • 02/18
14
Hilti Anchor Rod Specifications and Technical Data
Steel design information for the Hilti HAS Extended Anchor Rod Program for use with CSA A23.3-14 Annex D (Continued)
Vsa
(kN) (118.1) (150.0) (217.5) (294.1) (387.0) - -
Reduction factor, seismic shear αv,seis - 0.6 - -
Strength reduction factor R for tension2 R - 0.80 - -
Strength reduction factor R for shear 2 R - 0.75 - -
lb 57,250 72,685 105,375 142,500 187,500 - -
Nsa
HAS-E / HAS-E HDG
ASTM F1554 Gr. 551
Nsa
ASTM A193 B7 and
Vsa
(kN) (254.0) (322.5) (467.6) (632.4) (832.0) (1,081.6) (1,331.3)
Reduction factor, seismic shear αv,seis - 0.7 (3)
Strength reduction factor R for tension 2
R - 0.80
Strength reduction factor R for shear 2 R - 0.75
lb 43,510 55,240 80,085 108,300 142,500 - -
HAS-R Stainless Steel
ASTM A193, Gr. 8(M),
Nsa
(kN) (193.5) (245.7) (356.2) (481.7) (633.9) - -
Nominal strength as governed by steel strength
lb 26,105 33,145 48,050 64,980 85,500 - -
Class 1 1
Vsa
(kN) (116.1) (147.4) (213.7) (289.0) (380.3) - -
Reduction factor, seismic shear αv,seis - 0.6 - -
Strength reduction factor R for tension2 R - 0.80 - -
Strength reduction factor R for shear 2 R - 0.75 - -
1 Values provided for Hilti threaded rod materials based on published strengths and calculated in accordance with CSA A23.3-14 Annex D Eq. D.2 and Eq. D.31. Nuts and washers must
be appropriate for rod strength.
2 For use with the load combinations of CSA A23.3-14 Clause 8.
3 For HIT-RE 500 V3, the value of αv,seis can be increased. Refer to ICC-ES ESR-3814 or contact Hilti.
DBS • 02/18
15
EXTENDED HILTI ANCHOR ROD PROGRAM
LIMIT STATES DESIGN ACCORDING TO CSA A23.3-14 ANNEX D
The following steel design information is for the Hilti extended rod program according to the material specifications on page 10. The values are calculated from data on the
previous page. This is intended for adhesive anchors designed in accordance with CSA A23.3-14 Annex D and can be used in conjunction with the Hilti Simplified Strength
Design Tables (refer to Section 3.1.8 of the 2016 and 2017 Hilti Anchor Fastening Technical Guide for more information on the Hilti Simplified Tables). This includes Hilti
HIT-HY 200, HIT-RE 500 V3, HIT-RE 100, HIT-HY 100, and HIT-ICE. Bond strength design information for threaded rods larger than 1-1/4-inch diameter is currently only
available for HIT-RE 500 V3.
Steel design strength for Hilti HAS Extended Anchor Rod Program for use with CSA A23.3 Annex D
16
Hilti Anchor Rod Specifications and Technical Data
Note: Hilti HAS-V A36 threaded rods are not applicable for use with Hilti HVU Capsules since the end of the rod is not available with a chisel point to break and mix the
capsules during installation.
Allowable steel strength for the Hilti HAS Extended Anchor Rod Program 1
DBS • 02/18
17
EXTENDED HILTI ANCHOR ROD PROGRAM
TECHNICAL DATA — ALLOWABLE STRESS DESIGN (ASD) - CONTINUED
The following steel design information is for the Hilti extended rod program according to the material specifications on page 10. The following technical data is for adhesive
anchors that will be designed in accordance with the Allowable Stress Design Method (ASD). This includes Hilti HIT-HY 70 for masonry, HIT-HY 200 for masonry, HIT-ICE,
HIT-HY 10 PLUS, HIT-1, HTE 50 and HVU Capsules (must order threaded rods with chisel point for use with HVU Capsules).
Note:Hilti HAS-V A36 threaded rods are not applicable for use with Hilti HVU Capsules since the end of the rod is not available with a chisel point to break and mix the
capsules during installation.
Ultimate steel strength for the Hilti HAS Extended Anchor Rod Program 1
DBS • 02/18
18
Hilti Anchor Rod Specifications and Technical Data
The following threaded rod ordering information is for the Hilti extended rod program according to the material specifications on page 10.
1/2 2 144
5/8 3 144
3/4 4 144
Nominal anchor diameter (in.)
7/8 4 144
1 5 144
1-1/8 6 144
1-1/4 6 144
1-1/2 8 144
1-3/4 9 144
2 11 144
2-1/4 12 144
2-1/2 13 144
= typical lead time 2–4 working days plus shipping 2 = available but longer lead time
1 3/8-inch dia. threaded rods are not included in the ASTM F1554 standard. Hilti 3/8-inch dia. HAS-V, HAS-E, and HAS-E-B (incl. HDG) threaded rods meet the chemical composition and mechanical
property requirements of ASTM F1554.
2 up to following quantities: 3/8” to 3/4” > 250 pieces, 7/8” to 1-1/4” > 100 pieces, 1-1/2” to 2-1/2” > 50 pieces. Bigger quantities contact Hilti for lead time.
Hilti threaded rods in the Hilti Extended Anchor Rod Program are TWO END CUT OPTIONS AVAILABLE
stamped on the end to show grade of steel.
19