0 Bewertungen0% fanden dieses Dokument nützlich (0 Abstimmungen)
809 Ansichten1 Seite
This document provides error codes and explanations for 2G3G (GPRS) errors that may occur during installation of a security system. Key points:
- The SIM card PIN must be deactivated or set to 0000.
- Common error codes during the 2G3G test include 003 (SIM card not detected), 010 (SIM not inserted), 011 (PIN code necessary), and 030 (no network coverage).
- Potential causes of errors include SIM card activation delays, incorrect APN/username/password settings, insufficient GPRS network coverage, and typographical errors when entering settings.
- If errors occur, try re-running the 2G3G test after installation
This document provides error codes and explanations for 2G3G (GPRS) errors that may occur during installation of a security system. Key points:
- The SIM card PIN must be deactivated or set to 0000.
- Common error codes during the 2G3G test include 003 (SIM card not detected), 010 (SIM not inserted), 011 (PIN code necessary), and 030 (no network coverage).
- Potential causes of errors include SIM card activation delays, incorrect APN/username/password settings, insufficient GPRS network coverage, and typographical errors when entering settings.
- If errors occur, try re-running the 2G3G test after installation
This document provides error codes and explanations for 2G3G (GPRS) errors that may occur during installation of a security system. Key points:
- The SIM card PIN must be deactivated or set to 0000.
- Common error codes during the 2G3G test include 003 (SIM card not detected), 010 (SIM not inserted), 011 (PIN code necessary), and 030 (no network coverage).
- Potential causes of errors include SIM card activation delays, incorrect APN/username/password settings, insufficient GPRS network coverage, and typographical errors when entering settings.
- If errors occur, try re-running the 2G3G test after installation
2G3G Error Codes I N S T A L L A T I O N M A N U A L
IMPORTANT: The PIN of the SIM card has to be deactivated or 0000.
The following is a list of error codes that can appear after the 2G3G test.
In case of 2G3G (GPRS) errors during initial programming, we strongly
2G3G LEVEL : suggest to continue with the installation and perform the 2G3G (GPRS) level ERROR XXX test again once achieved.
This error checklist is provided for information purposes only.
This is not a comprehensive list, but it is representative of most Codes Errors cases. Some events or codes are subject to change by SIM card 1RQHWZRUNFRYHUDJHRUQR6,0FDUG operators. 03 ou 04LP LQVHUWHG However, the GPRS level test errors results in the majority of cases 003 6,0FDUGQRWGHWHFWHGQRWLQVHUWHG have the following causes : 010 6,0QRWLQVHUWHG • SIM Card activation Delay: 3,1FRGHQHFHVVDU\ Some operators require an additional delay up to 48 hours to 011 -> PIN code must be deactivated activate automatic data transmission. Please check with your operator prior to installation. 012 38.FRGHQHFHVVDU\6,0FDUGEORFNHG • APN CODE, USERNAME and PASSWORD : 013 'HIDXOW6,0FDUG The GPRS (2G3G) settings are supplied by the operator. Please make 014 6,0FDUGEXV\ sure you have entered the code exactly as indicated by your local 015 (UURURQ6,0 SIM card operator. Note: When entering your SIM card settings, both APN codes, • 1RQHWZRUNFRYHUDJH username and password fields are case sensitive! (It makes a 030, 043, • 7\SRJUDSKLFDOHUURULQWKH$31&RGH difference between UPPER and lower case letters) . 057, 102, XVHUQDPHSDVVZRUG 132, ... To switch between UPPER and lower case, use the M/m key from • 6,0FDUGQRWDFWLYDWHG CMA keypad or hold a digit key (0-9) for XMA/XMB.
• Insufficient GPRS Network:
When the panel is unable to find any signal, proceed to GPRS level test in another location on site. You can also find the network state or condition of use by directly contacting your local operator.