Beruflich Dokumente
Kultur Dokumente
XA YA XA YA
0 0 0,20 0,131
The solute A diffuses through stagnant B in the gas phase and then through a nondiffusing
liquid.
Using correlations for dilute solutions in wetted-wal towers, the film mass transfer
coefficient for A in the gas phase is predicted as Ky= 1,465 x 10-3 kg mol A/s.m2.molfrac
(1,08 ln mol/h. ft2 .mol frac) and the liquid phase as Kx = 1,967 x 10-3kg mol A/s.m2 .mol
frac(1,45 lb mol/h.ft2mol frac) calculate the interface concentrations yAI and XAI and the flux
NA.
Solution: since the correlation are for dilute solutions, (1- YA)iM and
(1 − 𝑥𝐴𝑖 ) − (1 − 𝑥𝐴𝑖 )
(1 − 𝑥𝐴 )𝑖𝑀 =
ln[(1 − 𝑥𝐴𝑙 /𝑥𝐴𝑖 )]
(1 − 0,100) − (1 − 0,247)
= 0,825
1 − 0,100
ln[1 − 0,247]
1,967 𝑥 10−3
𝑘𝑥′ /(1 − 𝑋𝐴 )𝑖𝑀 0,825
− ′ =− = −1,163
𝑘𝑦 /(1 − 𝑦𝐴 )𝑖𝑀 1,465 𝑥 10−3
0,715
A line through point P with a slope of – 1,163 is plotted and intersect equilibrium line at M,
where yAi = 0,197 ang xAi = 0,257.
Using these new values for the third trial, the following values are calculated:
(1 − 0,197) − (1 − 0,380)
(1 − 𝑦𝐴 )𝑖𝑀 = = 0,709
1 − 0,197
ln[1 − 0,380]
(1 − 0,100) − (1 − 0,257)
(1 − 𝑥𝐴 )𝑖𝑀 = = 0,820
1 − 0,100
ln[ ]
1 − 0,257
1,967 𝑥 10−3
𝑘𝑥′ /(1 − 𝑋𝐴 )𝑖𝑀 0,820
− ′ =− = −1,160
𝑘𝑦 /(1 − 𝑦𝐴 )𝑖𝑀 1,465 𝑥 10−3
0,709
This slope of – 1,160 is essentially the same as the slope of -1,163 for the second trial.
Hence,the final values are yAI = 0,197 and XAi = 0,257 and are shown as point M.
To calculate the flux, Eq.(10.4-8) is used.
The left-hand side of eq.(10.4-15) is the total resistance based on the overall gas driving
force and equals the gas film resistance 1/K*y plus the liquid film resistance m’/K’x
In a similar manner form fig.10.4-2,
X*A – XAL = (X*A- XAi) + (XAi + XAL)
𝑦𝐴𝐺 − 𝑦𝐴𝑖
𝑚′ =
𝑋𝐴∗ −𝑋𝐴𝐿
Proceeding as before,
1 1 𝑚
′
= ′′ ′ + ′
𝑘𝑥 𝑚 𝑘𝑦 𝑘𝑥
Several special cases of eqs.(10.4-15) and (10.4-18) will now be discussed. The
numerical values of K‘X and K’y are very roughly similar. The values of the slope m’-or m’’
are very important. If m’ is quite small, so that the equilibrium curve in fig. 10.4-2 is almost
horizontal, a small value of yA in the gas will give a large value of XA in equilibrium in the
liquid. The gas solute A is thent very soluble in the liquid phase, and hence the term m ’/ k’x
in eq.(10.4-15) is very small. Then,
1 1
=
𝐾𝑦𝑖 𝑘𝑥′
And the major resistance is in the gas phase, or the gas phase, or the gas phase is controlling.
The point M has moved down very close to E. so that
YAG – Y*A = YAG- YAi
Similary,when m’’ is very large, the solute A is very insoluble in the liquid, I/(m’’K’y)
become small, and
1 1
=
𝐾𝑥′ 𝑘𝑥′
The liquid phase is controlilling and XAi=X*A.systems for absorption of oxygen or CO2 form
air by water are similar to Eq.(10.4-3) is used.
𝐾𝑦′ 𝐾𝑥′
𝑁𝐴 = (𝑦𝐴𝐺 − 𝑦𝐴𝑖 ) = (𝑥 − 𝑥𝐴𝑙 )
(1 − 𝑦𝐴 )𝑖𝑀 (1 − 𝑥𝐴 )𝑖𝑀 𝐴𝑖
yAi – y*A = (yAG – yAi)+ m’(xAi-xAL)
we must, however,define the equations for the flux using overall coefficients as follows:
𝐾𝑦′ 𝐾𝑥′
𝑁𝐴 = [ ] (𝑦𝐴𝐺 − 𝑦𝐴∗ ) = [ ] (𝑥 ∗ − 𝑥𝐴𝐿 )
(1 − 𝑦𝐴 )∗𝑀 (1 − 𝑥𝐴 )∗𝑀 𝐴
Where Ky is the overall gas masss –transfer coefficient for A diffusing through stagnant B
and Kx the overall liquid mass-transfer coefficient. These two coefficients are concentration-
dependent. Substituting Eqs.(10.4-22) into (10.4-14), we obtain
1 1 𝑚′
= +
𝐾𝑦′ /(1 − 𝑦𝐴 )∗𝑚 𝐾𝑦′ /(1 − 𝑦𝐴 )𝑖𝑚 𝐾𝑥′ /(1 − 𝑋𝐴 )∗𝑚
Where
(1 − 𝑦𝐴∗ ) − (1 − 𝑦𝐴𝐺 )
(1 − 𝑦𝐴 )∗𝑀 =
ln[(1 − 𝑦𝐴∗ /𝑦𝐴𝐺 )]
Where
(1 − 𝑋𝐴𝐿 ) − (1 − 𝑋𝐴∗ )
(1 − 𝑥𝐴 )∗𝑀 =
ln[(1 − 𝑋𝐴𝐿 )/(1 − 𝑋𝐴∗ )]
It should be noted that the relations derived here also hold for any two- phase system where
y stands for the one phase and other phase. For example, for the extraction of the solute
acetic acid (A) from water (y phase) by isopropyl ether (x phase), the same relations will
hold.
ARTINYA:
Contoh 10.4-2 komposisi antarmuka dalam transfer massa interfase
Zat terlarut berasal dari campuran gas A dan B dalam menara dinding basah dengan cairan
yang mengalir sebagai film ke bawah di sepanjang dinding. Pada titik tertentu di menara
konsentrasi gas curah YAG = 0,38 fraksi mol dan konsentrasi cairan curah adalah XAL =
0,100. Menara beroperasi pada 298 k dan 1,013 105 pa, data kesetimbangannya adalah
sebagai berikut:
Mengikuti :
XA YA XA YA
0 0 0,20 0,131
Larutan A berdifusi melalui B yang stagnant dalam fase gas dan kemudian melalui cairan
yang tidak dipakai.
Dengan menggunakan korelasi untuk larutan encer dalam menara basah, koefisien
perpindahan massa film untuk A dalam fase gas diperkirakan sebagai Ky= 1,465 x 10-3 kg
mol A/s.m2.molfrac (1,08 ln mol/h. ft2 .mol frac) dan fase cair sebagai Kx = 1,967 x 10-3kg
mol A/s.m2 .mol frac(1,45 lb mol/h.ft2mol frac), hitunglah konsentrasi antarmuka YAI dan
XAI dan flux NA!
Solusi: karena korelasinya adalah untuk larutan encer, (1- YA)iM dan
Garis yang melalui titik P dengan slope (kemiringan) -1.342 diplot dalam gambar.10.4-4
memotong garis keseimbangan pada M1, di mana YAI= 0,183 dan XAI = 0,247.
Untuk uji coba kedua kami menggunakan YAI dan XAi dari uji coba pertama untuk
menghitung kemiringan baru. Menyubstitusikan keedalam persamaan. (10.4-6) dan (10.4-7),
(1 − 𝑦𝐴𝑖 ) − (1 − 𝑦𝐴𝐺 )
(1 − 𝑦𝐴 )𝑖𝑀 =
ln[(1 − 𝑦𝐴𝑖 /𝑦𝐴𝐺 )]
(1 − 0,183) − (1 − 0,380)
= 0,715
1 − 0,183
ln[1 − 0,380]
(1 − 𝑥𝐴𝑖 ) − (1 − 𝑥𝐴𝑖 )
(1 − 𝑥𝐴 )𝑖𝑀 =
ln[(1 − 𝑥𝐴𝑙 /𝑥𝐴𝑖 )]
(1 − 0,100) − (1 − 0,247)
= 0,825
1 − 0,100
ln[1 − 0,247]
1,967 𝑥 10−3
𝑘𝑥′ /(1 − 𝑋𝐴 )𝑖𝑀 0,825
− ′ =− = −1,163
𝑘𝑦 /(1 − 𝑦𝐴 )𝑖𝑀 1,465 𝑥 10−3
0,715
Garis melalui titik P dengan slope (kemiringan) - 1.163 diplot dan memotong garis
keseimbangan di M, di mana yAi = 0,197 dan xAi = 0,257.
Menggunakan nilai-nilai baru ini untuk percobaan ketiga, nilai-nilai berikut dihitung:
(1 − 0,197) − (1 − 0,380)
(1 − 𝑦𝐴 )𝑖𝑀 = = 0,709
1 − 0,197
ln[1 − 0,380]
(1 − 0,100) − (1 − 0,257)
(1 − 𝑥𝐴 )𝑖𝑀 = = 0,820
1 − 0,100
ln[ ]
1 − 0,257
1,967 𝑥 10−3
𝑘𝑥′ /(1 − 𝑋𝐴 )𝑖𝑀 0,820
− ′ =− = −1,160
𝑘𝑦 /(1 − 𝑦𝐴 )𝑖𝑀 1,465 𝑥 10−3
0,709
Kemiringan ini - 1.160 pada dasarnya sama dengan kemiringan -1,163 untuk percobaan
kedua. Oleh karena itu, nilai akhir adalah yAI = 0,197 dan XAi = 0,257 dan ditampilkan
sebagai titik M.
Untuk menghitung flux, persamaan. (10.4-8) digunakan
Bagian kiri dari persamaan (10.4-15) adalah resistansi total berdasarkan pada
keseluruhan tenaga penggerak gas dan sama dengan resistansi film gas 1/K*y
ditambah resistansi film cair m’/K’x
Pada bentuk yang serupa dari gambar.10.4-2,
X*A – XAL = (X*A- XAi) + (XAi + XAL)
𝑦𝐴𝐺 − 𝑦𝐴𝑖
𝑚′ =
𝑋𝐴∗ −𝑋𝐴𝐿
Dan hambatan utama adalah dalam fase gas, atau fase gas, atau fase gas mengendalikan.
Titik M telah bergerak turun sangat dekat dengan E. sehingga
YAG – Y*A = YAG- YAi
Sama halnya, ketika m’ sangat besar, zat terlarut A sangat tidak larut dalam cairan, I/(m’’K’y)
menjadi kecil, dan
1 1
′
= ′
𝐾𝑥 𝑘𝑥
Fase cair mengendalikan dan XAi=X*A. sistems untuk penyerapan bentuk oksigen atau CO2
udara dengan air mirip dengan persamaan(10.4-3) digunakan.
𝐾𝑦′ 𝐾𝑥′
𝑁𝐴 = (𝑦 )
− 𝑦𝐴𝑖 = (𝑥 − 𝑥𝐴𝑙 )
(1 − 𝑦𝐴 )𝑖𝑀 𝐴𝐺 (1 − 𝑥𝐴 )𝑖𝑀 𝐴𝑖
yAi – y*A = (yAG – yAi)+ m’(xAi-xAL)
Namun, kita harus menentukan persamaan untuk fluks dengan menggunakan koefisien
secara keseluruhan sebagai berikut:
𝐾𝑦′ 𝐾𝑥′
𝑁𝐴 = [ ] (𝑦𝐴𝐺 − 𝑦𝐴∗ ) = [ ] (𝑥 ∗ − 𝑥𝐴𝐿 )
(1 − 𝑦𝐴 )∗𝑀 (1 − 𝑥𝐴 )∗𝑀 𝐴
Dimana Ky adalah keseluruhan massa gas - koefisien transfer untuk A yang menyebar
melalui stagnant B dan Kx adalah koefisien perpindahan massa cairan keseluruhan. Kedua
koefisien ini bergantung pada konsentrasi. Mengganti Persamaan (10.4-22) menjadi (10.4-
14), kita dapatkan:
1 1 𝑚′
= +
𝐾𝑦′ /(1 − 𝑦𝐴 )∗𝑚 𝐾𝑦′ /(1 − 𝑦𝐴 )𝑖𝑚 𝐾𝑥′ /(1 − 𝑋𝐴 )∗𝑚
dimana
(1 − 𝑦𝐴∗ ) − (1 − 𝑦𝐴𝐺 )
(1 − 𝑦𝐴 )∗𝑀 =
ln[(1 − 𝑦𝐴∗ /𝑦𝐴𝐺 )]
dimana
(1 − 𝑋𝐴𝐿 ) − (1 − 𝑋𝐴∗ )
(1 − 𝑥𝐴 )∗𝑀 =
ln[(1 − 𝑋𝐴𝐿 )/(1 − 𝑋𝐴∗ )]
Perlu dicatat bahwa hubungan yang diturunkan di sini juga berlaku untuk sistem dua fase di
mana y berarti fase satu dan fase lainnya. Sebagai contoh, untuk ekstraksi asam asetat
terlarut (A) dari air (fase y) oleh isopropil eter (fase x), hubungan yang sama akan berlaku.
Dengan menggunakan data yang sama seperti pada contoh 10.4-1, hitung koefisien
perpindahan massa keseluruhan K'y, fluks, dan persen resistansi dalam lapisan gas dan
cairan. Lakukan ini untuk kasus A yang berdifusi melalui B jenuh.
Solusi: dari gambar.10.4-4, y*A= 0,052 yang berada dalam kesetimbangan dengan cairan
sebesar XAL= 0,10 dan juga , YAG=0,380.. Slope antara E dan M dari Persamaan (10,4-13)
adalah, untuk for yAi = 0,197 and XAi= 0,257,
𝑦 −𝑦 ∗ 0,197−0,052
𝑚′ = 𝑥 𝐴𝑖−𝑋 𝐴 = 0,257−0,100 = 0,923
𝐴𝑖 𝐴𝐿
Solusi, K’y= 8,90 x 19-4. Persen resistensi dalam lapisan gas adalah (484.0 / 868,8) 100 =
55,7% dan 44,3% dalam lapisan cair. Fluksnya adalah sebagai berikut, menggunakan
persamaan(10,4-22)
𝐾𝑦′ 8,90 𝑥 10−4
𝑁𝐴 = (𝑦𝐴𝐺 − 𝑦𝐴∗ ) = (0,380 − 0,052)
(1 − 𝑦𝐴 )∗𝑀 0,773
= 3,78 x 10-4 kg mol/s.m2