Sie sind auf Seite 1von 17

Keysight Technologies

Nemo Outdoor Samsung Chipset-Based


Terminals
(Chipsets 333/335/355)

Data Sheet

Anite is now part of Keysight Technologies


02 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Measure and Monitor the Newest


Wireless Network Technologies with
Powerful Drive Testing
Nemo Outdoor from Keysight Technologies, Inc. is an unparalleled
network measurement and optimization solution for perfecting
the air interface of wireless networks. It collects measurement
results and geographical coordinates, and these measurement
results further provide valuable information for network planning,
roll-out, tuning, verification, optimization, maintenance, and
benchmarking purposes. Nemo Outdoor is always among the
first-to-market with support for the very latest technologies. This
data sheet lists parameters and features available with Samsung
chipset-based terminals (chipsets 333/335/355) and Nemo
Outdoor.

Technical Specifications
Device specific features1
Device LTE WCDMA GSM CDMA/EVDO CA configurations
Samsung Galaxy FDD bands 1-5, 7, 8, 12, 17, 18, WCDMA 850, 900, Quad-band
Note 5 SM-N920G 19, 26, 28 1900, 2100

LTE TDD band 40


Samsung Galaxy LTE FDD 7 bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band CA 2CC intra-band contiguous:3C, 7C,
Note 5 SM-N920I 17, 18, 19, 26, 28 1900, 2100 40C, 1A, 3A, 7A, 8A, 40A, 2A, 4A, 12A,
(Samsung LTE TDD band 40 HSDPA UE Cat 24 17A, 26A, 5A, 18A, 19A, 28A
Shannon 333 LTE Cat 4, 6, 9 HSUPA UE Cat 6 CA 2CC intra-band non-contiguous:
chipset) 3A_3A
CA 2CC inter-band: 1A_3A, 1A_5A
(BCS 0,1), 1A_7A, 3A_5A (BCS 0,1,2),
3A_7A, 3A_8A (BCS 0,1,2), 3A_28A,
7A_8A, 3A_40A, 5A_40A, 7A_28A
(BCS 0,1), 28A_40A
CA 3CC inter-band: 3A_7C, 3C_7A,
1A_3A_5A (BCS 0,1), 3A_40C, 7C_28A,
28A_40C, 1A_3A_7A, 3A_7A_8A (BCS
0,1), 3A_7A_28A

1 The test devices tested and sold by Keysight Nemo Wireless Network Solutions are intended for testing purposes only. Software changes in devices may limit their normal
use. Keysight Nemo Wireless Network Solutions does its best to provide test devices without any limitations but it is not always possible. Keysight Nemo Wireless Network
Solutions assumes no liability if any commercial application or feature is blocked or limited due to software or other device-related modifications. If the test device is moved to
another country or used in the network of another operator than initially ordered, it is possible that the device does not support all network features. Keysight Nemo Wireless
Network Solutions assumes no liability in any cases.
03 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Device LTE WCDMA GSM CDMA/EVDO CA configurations


Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band CA 2CC intra-band contiguous:3C, 7C
S6 Edge+ SM-G928F 17-20, 26 1900, 2100 (BCS 0,1), 1A, 3A, 5A, 7A, 8A, 20A, 2A,
(Samsung LTE Cat 4, 6, 9 HSDPA UE Cat 24 4A, 12A, 17A, 18A, 19A, 26A
Shannon 333 HSUPA UE Cat 6 CA 2CC intra-band non-contiguous:
chipset) 3A_3A
CA 2CC inter-band: 1A_3A, 1A_5A
(BCS 0,1), 1A_7A, 1A_20A, 3A_5A
(BCS 0,1,2), 3A_7A, 3A_8A (BCS 0,1,2),
3A_20A (BCS 0,1), 7A_20A (BCS 0,1),
7A_8A
CA 3CC inter-band: 3A_7C, 3C_7A,
1A_3A_5A (BCS 0,1), 1A_3A_20A,
3A_7A_20A, 1A_3A_7A, 3A_7A_8A
(BCS 0,1)
Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band CA intra-band contiguous: 3C, 7C(BCS
S6 SM-G920F 17-20, 26 1900, 2100 0,1), 1A, 2A, 3A, 4A, 5A, 7A, 8A, 12A,
(Samsung LTE Cat 4, 6 HSDPA UE Cat 24, 17A, 18A, 19A, 20A, 26A
Shannon 333 HSUPA UE Cat 6 CA inter-band: 3A_7A, 7A_3A, 3A_20A
chipset) (BCS 0,1), 20A_3A (BCS 0,1), 7A_20A
(BCS 0,1), 20A_7A (BCS 0,1), 7A_8A
Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 1900, Quad-band CA inter-band: 2A_17A, 17A_2A,
S6 SM-G920A 17, 20, 29, 30 2100 4A_17A
(AT&T) (Samsung LTE Cat 4
Shannon 333
chipset)
Samsung Galaxy LTE FDD bands 1-5, 7, 12, 17, WCDMA 850, 1900, Quad-band CA intra-band contiguous: 2A, 4A, 12A,
S6 SM-G920T (T- 20 2100, AWS 1A, 3A, 5A, 7A, 17A, 20A
Mobile) (Samsung LTE Cat 4, 6 CA inter-band: 2A_4A (BCS 0,1,2),
Shannon 333 4A_2A (BCS 0,1,2), 4A_12A (BCS 0,3),
chipset) 12A_4A (BCS 0,3)
Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band CA intra-band contiguous: 3C, 7C (BCS
S6 SM-G920I 17, 18, 19, 26, 28 1900, 2100, AWS 0,1), 40C (BCS 0,1), 1A, 2A, 3A, 4A, 7A,
(APAC) (Samsung LTE TDD HSDPA UE Cat 24, 8A, 12A, 17A, 26A, 5A, 18A, 19A, 28A,
Shannon 333 LTE Cat 4, 6 HSUPA UE Cat 6 40A
chipset) CA inter-band: 3A_5A (BCS 0,1,2),
5A_3A (BCS 0,1,2), 3A_7A, 7A_3A,
3A_28A, 28A_3A, 7A_28A, 28A_7A
Samsung Galaxy LTE FDD bands 1-5, 7, 12, 13, WCDMA 850, 1900, Quad-band CA intra-band contiguous: 2A, 4A, 5A,
S6 SM-G920W8 17, 20, 29 2100, AWS 7A, 12A, 13A, 17A, 1A, 3A, 20A
(Bell) (Samsung LTE Cat 4, 6 CA inter-band: 2A_4A (BCS 0,1,2),
Shannon 333 4A_2A (BCS 0,1,2), 2A_17A, 17A_2A,
chipset) 4A_7A, 7A_4A, 4A_17A, 4A_12A (BCS
0,1,2,3,4), 2A_29A (BCS 0,1,2), 4A_29A
(BCS 0,1,2)
Samsung Galaxy LTE FDD bands 1, 2, 3, 5, 7, 8, WCDMA 850, 1900, Quad-band
6 Edge+ (SM- 17, 20, 26 2100
G928K) (Samsung LTE TDD bands 38, 39, 41
Shannon 333
chipset)
04 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Device LTE WCDMA GSM CDMA/EVDO CA configurations


Samsung Galaxy LTE FDD bands 3, 7, 20) WCDMA Quad-band 2CC CA intra-band contiguous: 3C, 7C
S7 (SM-G930F) LTE Cat 4, 6, 9 850/900/1900/ (BCS 0,1,2), 3A, 7A, 20A
(Samsung 2100AWS/2100 2CC CA intra-band non-contiguous:
Shannon 335 HSDPA UE Cat 24, 3A_3A, 7A_7A
chipset) HSUPA UE Cat 6 2CC CA inter-band: 3A_7A (BCS 0,1),
7A_3A (BCS 0,1), 3A_20A (BCS 0,1),
20A_3A (BCS 0,1), 7A_20A (BCS 0,1),
20A_7A (BCS 0,1)
3CC CA inter-band: 3A_7C (BCS 0,1),
7C_3A (BCS 0,1), 3C_7A, 7A_3C,
3C_20A, 20A_3C, 3A_7A_20A,
7A_3A_20A, 20A_3A_7A
Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band 2CC CA Intra-band contiguous: 3C, 7C
S7 Edge (SM- 13, 17-20, 25, 26, 28 1900, 2100AWS, 2100 (BCS 0,1,2), 38C, 40C (BCS 0,1)
G935F) (Samsung LTE TDD bands 38-41 2CC CA Intra-band non-contiguous:
Shannon 335 LTE Cat 4, 6, 9 3A_3A, 7A_7A, 40A_40A, 38A_38A
chipset) 2CC CA Inter-band: 1A_3A, 3A_1A,
1A_5A (BCS 0,1), 5A_1A (BCS 0,1),
1A_7A, 7A_1A, 1A_20A, 20A_1A, 3A_5A
(BCS 0,1,2,3), 5A_3A (BCS 0,1,2,3),
3A_7A (BCS 0,1), 7A_3A (BCS 0,1),
3A_8A (BCS 0,1,2,3), 8A_3A (BCS
0,1,2,3), 3A_20A (BCS 0,1), 20A_3A
(BCS 0,1), 3A_28A, 28A_3A, 3A_38A,
3A_40A, 3A_41A, 5A_40A (BCS 0,1),
7A_20A (BCS 0,1), 20A_7A (BCS 0,1),
7A_28A (BCS 0,1), 28A_7A (BCS 0,1),
20A_38A, 26A_40A, 28A_40A, 7A_8A
(BCS 0,1), 4A_28A
3CC CA Intra-band contiguous: 40D
3CC CA Intra-band non-contiguous:
40A_40C, 40C_40A
3CC CA Inter-band: 3C_5A, 5A_3C,
3A_7C (BCS 0,1), 7C_3A (BCS 0,1),
3C_7A, 7A_3C, 3C_20A, 20A_3C,
3A_40C, 7C_28A, 28A_7C, 28A_40C,
1A_3A_5A (BCS 0,1), 3A_1A_5A (BCS
0,1), 5A_1A_3A (BCS 0,1), 1A_3A_7A,
3A_1A_7A, 7A_1A_3A, 1A_3A_8A
(BCS 0,1,2), 3A_1A_8A (BCS 0,1,2),
8A_1A_3A (BCS 0,1,2), 1A_3A_20A,
3A_1A_20A, 20A_1A_3A, 3A_5A_40A,
5A_3A_40A, 3A_7A_20A, 7A_3A_20A,
20A_3A_7A, 3A_7A_28A, 7A_3A_28A,
28A_3A_7A, 3A_8A_38A, 8A_3A_38A,
3A_28A_38A, 28A_3A_38A, 3A_7A_8A
(BCS 0,1), 7A_3A_8A (BCS 0,1)
Samsung LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band
Galaxy S7 Edge 13, 17-20, 25, 26, 28 1700, 1900, 2100
(SM-G935FD) LTE TDD bands 38-41
(Samsung LTE Cat 9
Shannon 335
chipset)
05 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Device LTE WCDMA GSM CDMA/EVDO CA configurations


Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band 2CC CA intra-band contiguous: 1CA,
S8 (SM-G950F) 13, 17-20, 25, 26, 28, 32, 66 1900, 2100AWS, 2100 3CA, 7CA (BCS 0,1,2), 38CA, 40CA
(Samsung Shannon LTE TDD bands 38-41 HSDPA UE Cat 24, (BCS 0,1), 41CA (BCS 0,1,2,3)
355 chipset) LTE Cat 4, 6, 9 HSUPA UE Cat 6 2CC CA intra-band non-contiguous:
LTE-A (4 CA) Cat 16 (1024/150) 3AA_3A (BCS 0,1), 7AA_7A (BCS 0,1),
Note: Capabilities are market 41AA_41A (BCS 0,1), 40AA_40A
and operator specific. 2CC CA inter-band: 1AA_3A, 3AA_1A,
1AA_5A (BCS 0,1), 5AA_1A (BCS
0,1), 1AA_7A, 7AA_1A, 1AA_8A
(BCS 0,1,2), 8AA_1A (BCS 0,1,2),
1AA_20A, 20AA_1A, 1AA_28A (BCS
0,1), 28AA_1A (BCS 0,1), 3AA_5A
(BCS 0,1,2,3), 5AA_3A (BCS 0,1,2,3),
3AA_7A (BCS 0,1), 7AA_3A (BCS 0,1),
3AA_8A (BCS 0,1,2,3), 8AA_3A (BCS
0,1,2,3), 3AA_20A (BCS 0,1), 20AA_3A
(BCS 0,1), 3AA_28A, 28AA_3A,
3AA_32A, 3AA_38A, 3AA_41A,
5AA_7A (BCS 0,1), 7AA_5A (BCS 0,1),
7AA_20A (BCS 0,1), 20AA_7A (BCS
0,1), 7AA_28A (BCS 0,1), 28AA_7A
(BCS 0,1), 20AA_32A, 20AA_38A,
2AA_28A, 28AA_2A, 4AA_13A (BCS
0,1), 13AA_4A (BCS 0,1), 3AA_40A,
5AA_40A (BCS 0,1)
3CC CA intra-band: 41DA
3CC CA inter-band: 3CA_5A,
5AA_3C, 3CA_7A, 7AA_3C, 3CA_20A,
20AA_3C, 3AA_7C (BCS 0,1),
7CA_3A (BCS 0,1), 1AA_3A_5A
(BCS 0,1), 3AA_1A_5A (BCS 0,1),
5AA_1A_3A (BCS 0,1), 1AA_3A_7A,
3AA_1A_7A, 7AA_1A_3A, 1AA_3A_8A
(BCS 0,1,2,3), 3AA_1A_8A (BCS
0,1,2,3), 8AA_1A_3A (BCS 0,1,2,3),
1AA_3A_20A, 3AA_1A_20A,
20AA_1A_3A, 1AA_3A_28A,
3AA_1A_28A, 28AA_1A_3A,
1AA_7A_20A, 7AA_1A_20A,
20AA_1A_7A, 3AA_3A_5A,
5AA_3A_3A, 3AA_3A_7A,
7AA_3A_3A, 3AA_3A_20A,
20AA_3A_3A, 3AA_3A_32A,
3AA_7A_7A, 7AA_7A_3A,
3AA_7A_20A, 7AA_3A_20A,
20AA_3A_7A, 3AA_7A_28A,
7AA_3A_28A, 28A_3A_7A,
3AA_8A_38A, 8AA_3A_38A,
3AA_20A_32A, 20AA_3A_32A,
3AA_20A_38A, 20AA_3A_38A,
3AA_28A_38A, 28AA_3A_38A,
3AA_38A_38A, 20AA_38A_38A,
3AA_40C, 3AA_40A_40A,
41AA_41A_40A, 40AA_41A_41A,
41AA_41A_41A
06 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Device LTE WCDMA GSM CDMA/EVDO CA configurations


Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band 2CC CA intra-band contiguous: 1CA,
S8+ (SM-G955F) 13, 17-20, 25, 26, 28, 32, 66 1900, 2100AWS, 2100 3CA, 7CA (BCS 0,1,2), 38CA, 40CA
(Samsung Shannon LTE TDD bands 38-41 HSDPA UE Cat 24, (BCS 0,1), 41CA (BCS 0,1,2,3)
355 chipset) LTE Cat 4, 6, 9 HSUPA UE Cat 6 2CC CA intra-band non-contiguous:
LTE-A (4 CA) Cat 16 (1024/150) 3AA_3A (BCS 0,1), 7AA_7A (BCS 0,1),
Note: Capabilities are market 41AA_41A (BCS 0,1), 40AA_40A
and operator specific. 2CC CA inter-band: 1AA_3A, 3AA_1A,
1AA_5A (BCS 0,1), 5AA_1A (BCS
0,1), 1AA_7A, 7AA_1A, 1AA_8A
(BCS 0,1,2), 8AA_1A (BCS 0,1,2),
1AA_20A, 20AA_1A, 1AA_28A (BCS
0,1), 28AA_1A (BCS 0,1), 3AA_5A
(BCS 0,1,2,3), 5AA_3A (BCS 0,1,2,3),
3AA_7A (BCS 0,1), 7AA_3A (BCS 0,1),
3AA_8A (BCS 0,1,2,3), 8AA_3A (BCS
0,1,2,3), 3AA_20A (BCS 0,1), 20AA_3A
(BCS 0,1), 3AA_28A, 28AA_3A,
3AA_32A, 3AA_38A, 3AA_41A,
5AA_7A (BCS 0,1), 7AA_5A (BCS 0,1),
7AA_20A (BCS 0,1), 20AA_7A (BCS
0,1), 7AA_28A (BCS 0,1), 28AA_7A
(BCS 0,1), 20AA_32A, 20AA_38A,
2AA_28A, 28AA_2A, 4AA_13A (BCS
0,1), 13AA_4A (BCS 0,1), 3AA_40A,
5AA_40A (BCS 0,1)
3CC CA intra-band: 41DA
3CC CA inter-band: 3CA_5A,
5AA_3C, 3CA_7A, 7AA_3C, 3CA_20A,
20AA_3C, 3AA_7C (BCS 0,1),
7CA_3A (BCS 0,1), 1AA_3A_5A
(BCS 0,1), 3AA_1A_5A (BCS 0,1),
5AA_1A_3A (BCS 0,1), 1AA_3A_7A,
3AA_1A_7A, 7AA_1A_3A, 1AA_3A_8A
(BCS 0,1,2,3), 3AA_1A_8A (BCS
0,1,2,3), 8AA_1A_3A (BCS 0,1,2,3),
1AA_3A_20A, 3AA_1A_20A,
20AA_1A_3A, 1AA_3A_28A,
3AA_1A_28A, 28AA_1A_3A,
1AA_7A_20A, 7AA_1A_20A,
20AA_1A_7A, 3AA_3A_5A,
5AA_3A_3A, 3AA_3A_7A,
7AA_3A_3A, 3AA_3A_20A,
20AA_3A_3A, 3AA_3A_32A,
3AA_7A_7A, 7AA_7A_3A,
3AA_7A_20A, 7AA_3A_20A,
20AA_3A_7A, 3AA_7A_28A,
7AA_3A_28A, 28A_3A_7A,
3AA_8A_38A, 8AA_3A_38A,
3AA_20A_32A, 20AA_3A_32A,
3AA_20A_38A, 20AA_3A_38A,
3AA_28A_38A, 28AA_3A_38A,
3AA_38A_38A, 20AA_38A_38A,
3AA_40C, 3AA_40A_40A,
41AA_41A_40A, 40AA_41A_41A,
41AA_41A_41A
07 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Device LTE WCDMA GSM CDMA/EVDO CA


configurations
Samsung Galaxy LTE FDD bands 1-5, 7, 8, 12, WCDMA 850, 900, Quad-band
Note 8 SM-N950F 13, 17-20, 25, 26, 28 1700, 1900, 2100
(Samsung Shannon LTE TDD bands 38-41
355 chipset) LTE Cat 16
Note: Capabilities are market
and operator specific.

Samsung Galaxy LTE FDD bands 1, 3, 7, 8, 28 WCDMA 850, 1700, Quad-band


S9 SM-G960F LTE TDD band 40 1900, 2100, 2600
LTE Cat 18
Note: Capabilities are market
and operator specific.
08 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Supported Features and Parameters Physical channel information 


–– PDSCH throughput 3
Supported parameters depend on the ICD version. This data –– PDSCH BLER3
sheet presents the latest ICD in use. –– PUSCH throughput 
–– PUSCH TX power 
Forcing features –– PUSCH TX power headroom (not available with 333)
–– PUCCH TX power
Forcing features vary depending on device model and firmware
–– SNR3
version. Please see the table at the end of this data sheet for
–– SNR per antenna3
detailed information about the available forcing features per
–– LTE SRS power (not available with 333)
device.
–– System lock (requires NMR with Samsung Shannon)
–– Band lock (GSM, WCDMA, LTE) (requires NMR with Samsung
Radio access bearer (RAB) information
Shannon) –– RAB type (PS)
–– Enabling/disabling terminal radio –– RAB ID
–– Sending and logging custom AT commands and responses –– RAB RB ID
–– GSM channel lock1 –– RAB allocation attempts
–– Setting preferred channel (UMTS) 1 –– RAB allocation success
–– UMTS channel and scrambling code lock1 –– RAB allocation failure with failure cause type
–– LTE channel and PCI lock1 –– RAB release with release type
–– LTE-A carrier aggregation forcing (enable/disable)
Link adaptation (for primary and secondary
Application protocols serving cells, reported for one modulation/PRB
–– ICMP ping allocation per sample duration)
–– Ping trace route testing –– PDSCH rank
–– FTP2 –– PDSCH modulation and MCS per code word
–– SFTP –– PDSCH PRB allocation 
–– HTTP/S2 –– LTE precoding matrix indicator (PMI)
–– HTTP/S browsing including content encoding –– PUSCH rank 
–– HTTP streaming (YouTube) –– PUSCH modulation and MCS
–– Iperf service testing (for TCP and UDP) –– PUSCH PRB allocation 
–– SMTP/S, POP3/S, and IMAP/S protocols (for email testing)
–– SMS testing Current cell information
–– RTSP streaming
–– Facebook, Twitter, Instagram (limited functionality), Dropbox –– Physical cell identity 3
–– Physical layer identity 3
Cell specific frequency shift 3
LTE –– Channel number (EARFCN) 3
Cell measurement (for each cell) –– Cell ID
–– Tracking area code
–– Cell type (serving, secondary serving, listed, detected) –– Mobile country code
–– Band –– Mobile network code
–– Channel number (EARFCN) –– MME group ID
–– Physical cell identity –– MME code
–– RSSI –– M-TMSI
–– RSRP –– RRC state
–– RSRQ –– Cell bandwidth3
–– RSRP, RSRQ, RSSI, cell frame timing, and cell frame offset –– Transmission mode3
per antenna port (not available with 333) –– Detected downlink antenna ports 3
–– Pathloss (not available with 333) –– Service status
–– Inter-system cell measurements –– Cyclic prefix 3
–– Logging LTE inter-system neighbor cell list –– Automatic neighbor relations (ANR) CGI reporting
–– C-RNTI
–– Number of secondary serving cells
–– Secondary serving cell activity state
1.  Supported with limited set of handsets and may require NMR installed to test handset
2.  Multi-thread, download/upload
3.  For primary and secondary serving cells
09 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

CQI (for primary and secondary serving cells) –– RRC connection release
–– RRC connection release status
–– Wideband CQI per code word –– RRC connection release cause
–– Requested rank –– RRC re-establishment status
–– Periodic and aperiodic CQI reporting mode –– RRC re-establishment cause
–– LTE measurement events A1-A6 and B1-B2
RACH parameters
–– RACH type MAC
–– Reason –– MAC uplink retransmission rate (total)
–– Preamble ID
–– RACH result
–– Maximum allowed preambles
Upper layers
–– Number of transmitted preambles –– RRC signaling
–– Number of received preamble responses (success and –– NAS signaling
backoff cases separated) –– RRC state
–– Number of contention resolution failures –– EMM state
–– RA-RNTI –– LTE EPS bearer events
–– RACH response window size
–– RACH timing advance VoLTE, ViLTE, VoWiFi, and ViWiFi information
–– RACH access delay
–– AMR rate and EVS rate
Mobility parameters
RTP signaling messages
–– Cell reselections events
–– Handover events (attempt/success/failure) With Samsung Shannon, RTP signaling messages are only logged
–– Handover type for VoWiFi/ViLTE video and ViWiFi audio and video packets.
–– Tracking area update events (attempt/success/failure) –– Direction (DL/UL)
–– Tracking area update events (attempt/success/failure) –– Message name
–– Tracking area update type –– Message sequence number
–– Tracking area update failure cause –– Message data
–– Handover duration
–– Handover U-plane interruption time (VoLTE/ViLTE) RTP packet information
–– Handover to preamble time
–– Jitter
–– RTP inter arrival jitter based on RFC 3550 subclause 6.4.1
RLC/PDCP –– RTP PER (number of lost packets based on sequence number
–– RLC downlink throughput before de-jitter buffer)
–– RLC downlink throughput per RB –– IAT
–– RLC uplink throughput DL RTP inter-arrival time downlink (maximum time between
–– RLC uplink throughput per RB RTP packets)
–– RLC downlink BLER –– RTP DL/UL bytes
–– RLC downlink BLER per RB –– RTP DL/UL packets
–– RLC uplink retransmission rate –– RTP burst error length
–– RLC uplink retransmission rate per RB
–– PDCP downlink throughput SIP registration events
–– PDCP downlink throughput per RB
–– Attempt
–– PDCP uplink throughput
–– Failure with cause code
–– PDCP uplink throughput per RB
–– Completed
–– Deregistered
Radio resource connections (RRC) –– SIP server re-registration result
–– RRC connection attempts
–– RRC establishment cause IMS SIP signaling messages
–– RRC connection success/failures
–– Direction (DL/UL)
–– Number of RRC connection requests before RRC connection
–– Message name
–– Number of RRC connection requests before abort
–– Message data
–– RRC rejection status
10 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

WCDMA Radio access bearer (RAB) information


Serving cell information –– RAB type (CS/PS)
–– RAB ID
–– Cellular system –– RAB RB ID
–– Channel number for primary and secondary channels –– RAB allocation attempts
–– Service information –– RAB allocation success
–– RAC, MCC –– RAB allocation failure with failure cause type
–– MNC, LAC –– RAB release with release type

AMR information Power control parameters


–– AMR mode UL/DL (not available with 333) –– BLER
–– SIR
WCDMA signaling messages –– SIR target
–– TX power control algorithm
–– Layer 3
–– TX power control step size
–– RRC messages
–– Number of increase/decrease UL/DL power commands
–– Logical subchannels for all messages

RACH parameters Soft handover parameters


–– Ec/No for active/neighbor/detected set
–– Random access maximum preamble count
–– Soft handover status
–– Random access preamble count
–– Soft handover event
–– Random access message TX power
–– Addition window
–– UL interference level
–– Drop window
–– Replacement window
RLC –– Time to trigger 1A
–– RLC uplink throughput –– Time to trigger 1B
–– RLC downlink throughput –– Time to trigger 1C
–– RLC uplink retransmission rate –– Added scrambling code number
–– Number of RBs –– Removed scrambling code number
–– RB ID –– Cell count active
–– RLC uplink throughput per RB –– Cell count monitored
–– RLC downlink throughput per RB
Additional 3G information
HSDPA parameters –– Compressed mode indication
–– HSDPA UE category –– RRC state
–– Current HSDPA serving scrambling code –– WCDMA neighbor list with GSM neighbors
–– CQI –– Neighbor cell index
–– Inter-system GSM neighbor measurement results
–– Results of inter-frequency neighbor measurements
HSUPA parameters
–– Measurement events
–– HSUPA UE category –– Used AMR codec (not available with 333)
–– TTI –– WCDMA pilot pollution analysis
–– Primary and secondary E-RNTI –– Source system
–– Distribution of used E-TFCI (not available with 333) –– Source band
–– Happy bit status (not available with 333) –– Source channel number
–– MAC-e throughput (not available with 333) –– Pilot pollution scr code
–– Pilot pollution Ec/N0
Physical layer parameters –– Pilot pollution RSCP
–– Cell name of polluting pilot (if cell site file is used)
–– BLER, RSSI, RSCP for primary and secondary channels
–– Cell ID of polluting pilot (if cell site file is used)
–– TX power
–– Ec/No and RSCP for active/neighbor/detected set
–– FER (voice) (not available with 333)
11 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

GSM –– Call connection time from attempt to connected state


–– Call attempt time
GSM interference analysis parameters (scanner
–– Call failure time
required simultaneously for measurements) –– Call failure cause
–– User adjustable thresholds: RX level sub and RX quality sub –– Call duration
–– Interference analysis channel type: serving channel, co- –– Call disconnect cause
channel or adjacent channel –– Call direction (MOC/MTC)
–– Band
–– Channel number Packet data information
–– BSIC
–– PDP activation attempt time
–– RX level
–– PDP active duration
–– Cell name (requires cell site file)
–– PDP activation failure time
–– PDP activation failure cause
GSM signaling messages –– PDP context deactivation time
–– Layer 3 –– PDP context deactivation cause
–– RLC/MAC control messages –– Packet state
–– Logical subchannels for all messages –– Packet protocol address
–– Attach failure time
–– Attach failure cause
GSM serving cell RF parameters
–– Attach attempt time
–– RXLEV (full and sub) –– Attach duration
–– RXQUAL (full & sub) –– Detach time
–– C1 & C2 –– GMM/SM state
–– TXPOWER –– QoS settings
–– Timing advance
–– Signal variance WLAN cell measurements
–– Mean BEP (8-PSK & GMSK)
–– Mean BEP coefficient variance (8-PSK & GMSK) –– Channel number
–– SSID and BSSID
–– IP address
GSM serving channel information
–– RSSI
–– BSIC –– Quality
–– TCH (HR, FR, EFR) –– Security mode and link speed
–– Timeslot number –– WLAN state information
–– Channel number
User level data information
GSM neighbor information
–– Data transfer protocol
–– BCCH –– Data transfer direction
–– BSIC –– Data transfer attempt number
–– RXLEV –– Data transfer host address
–– C1 & C2 –– Data transfer host port
–– GSM neighbor list with WCDMA neighbors –– Application data throughput UL/DL
–– Inter-system WCDMA neighbor measurement results –– Application packet error rate
–– Transferred bytes UL/DL
RLC/MAC information –– PPP layer data throughput
–– Data connection establishment time
–– Number of timeslots UL/DL
–– Data connection rate UL/DL
–– EDGE modulation and coding scheme UL/DL
–– Data connection duration
–– GPRS/EDGE indication
–– Data connection failure time
–– RLC data throughput UL/DL
–– Data connection failure cause
–– Data transfer failure cause
Call information –– Data size UL/DL
–– Call type –– Data disconnect cause
–– Number of calls –– Ping rate Ping timeout
–– Call connecting status –– Ping time (application data round trip travel time)
12 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

–– IP access and termination time (when TCP/IP packet VoLTE voice statistics
capturing enabled from the OS)
–– DNS query address –– VoLTE calls (number of VoLTE calls)
–– DNS query latency –– VoLTE calls alerting (number of alerting VoLTE calls)
–– DNS query result –– VoLTE call attempt failures (number of call attempt failures)
–– DNS resolved address –– LTE call accessibility, % (ratio of call attempt failures/call
attempts in LTE)
–– Overall call connects, answered (number of all answered calls)
Video quality metrics –– Overall call accessibility (ratio of all call attempt failures/all call
Video quality is measured passively from media streams carried attempts in all systems)
over packet-based networks. Factors that affect quality include –– Overall call attempt failures, system failure (number of call
delay variations, packet losses and other distortions which may attempt failures)
be visible in the video. Also factors, such as the video codec itself –– Overall call attempt failures, incoming call not received
are included in the final result. However, end-to-end and round- (number of call attempt failures)
trip delays are not taken into account. –– Overall call connects, TCH (number of call all connected calls)
–– Overall call setup time, TCH (time between call attempt to call
–– Video quality MOS absolute (video quality is normally connection)
displayed as mean opinion score (MOS), which is expressed –– Overall call setup time, alerting (time between call attempt to
as a single number. The range varies from 1 to 5, where 1 is call alert)
poor quality and 5 is perfect. Usually the MOS value does –– Overall call setup time, answered (time between call attempt
not reach 5, the practical maximum being most commonly to call answer)
between the values 3 and 4.) –– LTE call setup time, ms (time between call attempt to call
–– Video quality MOS relative (relative MOS is calculated similar connection when in LTE
to absolute MOS except without using resolution; video –– IMS registration failure rate (ratio of IMS registration attempts/
streams with different resolutions should get comparable failures)
MOS results.) –– VoLTE calls answered (number of answered VoLTE calls
–– Video/audio quality MOS absolute (combined audio and video –– VoLTE call disconnects, dropped (number of dropped VoLTE
MOS) calls)
–– Video/audio quality MOS relative (combined audio and video –– Overall calls (number of all voice calls)
MOS excluding resolution from the calculation) –– Overall calls received (number of all received voice calls)
–– Video quality average bitrate –– Overall call disconnects, normal (number of all disconnected
–– Video codec (defines the video codec used in the container voice calls)
format, usually this is H.263, H.263+, H.264 (MPEG4 Part –– Overall call disconnects, dropped (number of all dropped calls
10) or MPEG4 visual (MPEG4 Part 2) when streaming mobile in all systems
content) –– Overall call disconnects, early release (number of all calls
released early in all systems)
Audio quality metrics –– Overall call drop rate, % (ratio of all disconnects (drops)/all call
connections with alerting state)
–– Audio quality MOS-LQ (estimated listening quality MOS is –– Overall call success rate (ratio of all successful calls)
calculated from the listening quality R-factor that ignores –– Overall call attempt success rate (ratio of all successful call
effect of delay and recency, the value should be comparable attempts)
with PESQ score) –– Overall call duration, TCH (total duration of all calls)
–– Audio quality MOS-CQ (estimated conversation quality MOS –– Overall call duration, alerting (total duration of all alerting calls)
is calculated from the conversation quality R-factor) –– Overall call duration, answered (total duration of all answered
–– Audio quality R-factor LQ (listening quality R-factor is calls
calculated from E-model by ignoring the effect of delay and –– VoLTE intra LTE handover failures (number of handover failures
recency) during intra LTE HO)
–– Audio quality R-factor CQ (conversation quality R-factor is –– VoLTEe intra LTE handover failure rate, % (ratio of Volte intra
calculated including delay and recency to the result) LTE HO failures/VoLTE intra HO attempts)
–– SRVCC failures, RAN view (number of failed Inter-system
handovers from LTE)
–– SRVCC failure rate, RAN view (%) (ratio of inter-system
handovers failures/inter-system handover attempts from LTE)
–– VoLTE POLQA DL average (average POLQA DL score per VoLTE
call)
–– VoLTE POLQA DL average before SRVCC, to match Nemo
Outdoor naming convention (average POLQA DL score per
VoLTE call before SRVCC)
13 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

WLAN (VoWiFi and ViWiFi) statistics –– CSFB voice call statistics:


–– CSFB voice call attempts
–– WLAN IMS registration attempts –– CSFB voice call attempt failures
–– WLAN IMS registration success –– CSFB voice call attempt failures (system failure)
–– WLAN IMS registration failures –– CSFB voice call connects
–– WLAN IMS registration success rate –– CSFB voice calls received
–– WLAN IMS registration failure rate –– CSFB voice call attempt success rate
–– WLAN IMS voice call attempt failures –– CSFB voice call setup time
–– WLAN IMS voice call attempt failures (system failure) –– Virtual statistics parameters:
–– WLAN IMS voice call connects –– Average application data throughput DL
–– WLAN IMS voice calls alerting –– Average application data throughput UL (The calculation
–– WLAN IMS voice calls answered is made between data request (DREQ) to data completed
–– WLAN IMS voice call disconnects (normal) event (DCOMP) weighted by time. The result is shown for
–– WLAN IMS voice call disconnects (dropped) each data transfer context ID separately.)
–– WLAN IMS voice calls received –– Average PPP data throughput DL
–– WLAN IMS video call attempt failures –– Average PPP data throughput UL
–– WLAN IMS video call attempt failures (system failure) –– Average video streaming quality MOS (average value is
–– WLAN IMS video call connects calculated real time during the video streaming over the
–– WLAN IMS video calls alerting one video streaming session)
–– WLAN IMS video calls answered
–– WLAN IMS video call disconnects (normal)
–– WLAN IMS video call disconnects (dropped)
Real-time statistics
–– WLAN IMS video calls received Real-time statistics are virtual parameters that are not written
–– IMS voice call LTE to WLAN handover success in the measurement file. Real-time statistics can be displayed in
–– IMS voice call LTE to WLAN handover rejected different views in Nemo Outdoor and they are written in the csv.
–– IMS voice call LTE to WLAN handover failed file.
–– IMS voice call LTE to WLAN handover timeout –– Distribution statistics
–– IMS voice call WLAN to LTE handover success –– GPRS coding scheme distribution (DL/UL)
–– IMS voice call WLAN to LTE handover rejected –– EDGE coding scheme distribution (DL/UL)
–– IMS voice call WLAN to LTE handover failed –– Data throughput statistics including min/max/average values
–– IMS voice call WLAN to LTE handover timeout –– Application data throughput (DL/UL)
–– IMS video call LTE to WLAN handover success –– UMTS L1 statistics including min/max/average values
–– IMS video call LTE to WLAN handover rejected –– Ec/N0 best active
–– IMS video call LTE to WLAN handover failed –– RSCP best active
–– IMS video call LTE to WLAN handover timeout –– TX power
–– IMS video call WLAN to LTE handover success –– BLER
–– IMS video call WLAN to LTE handover rejected –– Counter statistics for measurement events (MEI event)
–– IMS video call WLAN to LTE handover failed –– GSM L1 statistics including min/max/average values
–– IMS video call WLAN to LTE handover timeout –– RXL full/sub
–– RXQ full/sub
Statistics –– TX power
–– Timing advance
–– Call statistics –– LTE L1 statistics
–– Handover/handoff statistics –– RSRQ serving measurement average
–– Soft handover statistics –– RSRP serving measurement average
–– Intersystem handover statistics
–– Intersystem cell reselections
–– Location area statistics
–– Attach statistics
–– PDP context statistics
–– Routing area statistics
–– User level data statistics
–– Video streaming statistics:
–– Streaming setup success rate
–– Streaming setup delay
–– Streaming completion success rate
14 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Ordering Information
License options
Order number Handler/license
NTA50159A Handler for Samsung Shannon 333/335/355 GSM/UMTS
NTA50160A Handler for Samsung Shannon 333/335/355 GSM/UMTS/LTE
NTA50161A Handler for Samsung Shannon 333/335/355 GSM/UMTS/LTE-A 2CC
NTA50162A Handler for Samsung Shannon 333/335/355 GSM/UMTS/LTE-A 3CC
NTA50163A Handler for Samsung Shannon 333/335/355 GSM/UMTS/LTE-A 4CC
NTA50127A Handler for Samsung Shannon 333/335/355 GSM/UMTS/LTE-A 5CC
Features per device
Band
lock
System (GSM,
lock WCDMA, WCDMA Airline
(GSM, LTE, GSM WCDMA scr. code LTE ch LTE CA mode
Voice Video PS WCDMA, CDMA, channel ch lock lock (sector lock PCI enable/ (radio on/ Ext.
Device call VQ call VoLTE data1 SMS MMS USSD LTE) EVDO) lock (UARFCN) lock) (EARFCN) lock disable off) ant. Multi2
Samsung x NMR x x 1
Galaxy Note
5 SM-N920G
Samsung X NMR Operator x x 3 pcs 8 (Nemo
specific Walker)
Galaxy S6
FW and 6 (Nemo
SM-G920F NMR Multi
Lite)

Samsung X NMR Operator x x 1


specific
Galaxy S6
FW and
SM-G920I NMR
(SEAP)
X NMR x x x 4 pcs 1
15 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Samsung
Galaxy S6
SM-G920T
(T-Mobile)
Samsung X NMR x x 4 pcs 1
Galaxy S6
SM-G920W8
(Bell)
Samsung X x 4 pcs 1
Galaxy S6
SM-G920A
(AT&T)
Samsung X NMR Operator x NMR NMR WCDMA/ x x x x 1
specific LTE (NMR)
Galaxy
FW and
S6 Edge+ NMR
SM-G928F
Samsung X NMR x x x 1
Galaxy
6 Edge+
(SM-G928K)

1.  FTP, HTTP, e-mail, ICMP ping


2.  Verified number of simultaneous devices in multi configuration with single CPU
Band
lock
System (GSM,
lock WCDMA, WCDMA Airline
(GSM, LTE, GSM WCDMA scr. code LTE ch LTE CA mode
Voice Video PS WCDMA, CDMA, channel ch lock lock (sector lock PCI enable/ (radio on/ Ext.
Device call VQ call VoLTE data1 SMS MMS USSD LTE) EVDO) lock (UARFCN) lock) (EARFCN) lock disable off) ant. Multi2
Samsung X NMR Operator x NMR NMR GSM/ x x x x 1
specific WCDMA/
Galaxy Note
FW and LTE (NMR)
5 SM-N920I NMR

Samsung X NMR NMR x x WCDMA/ 1


(ENG FW (ENG FW LTE
Galaxy S7
required) required)
(SM-G930F)
Samsung X NMR NMR x x x WCDMA/ x x x x 1
(ENG FW (ENG FW LTE
Galaxy
required) required)
S7 Edge
(SM-G935F)
Samsung X NMR NMR x x WCDMA/ 1
(ENG FW (ENG FW LTE
Galaxy S7
required) required)
Edge (SM-
16 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

G935FD)
(Samsung
Shannon
335 chipset)
Samsung x NMR NMR x x (single x (single x x x x x x 9
(ENG FW (ENG FW system) band)
Galaxy S8
required) required)
(SM-G950F)
Samsung x NMR NMR x x (single x (single x x x x x x 1
(ENG FW (ENG FW system) band)
Galaxy S8+
required) required)
(SM-G955F)
Samsung x x 1
Galaxy S9
SM-G960F

1.  FTP, HTTP, e-mail, ICMP ping


2.  Verified number of simultaneous devices in multi configuration with single CPU
17 | Keysight | Nemo Outdoor Samsung Chipset-Based Terminals - Data Sheet

Evolving Since 1939 For more information on Keysight


Technologies’ products, applications or
Our unique combination of hardware, software, services, and people can help you services, please contact your local Keysight
reach your next breakthrough. We are unlocking the future of technology. office. The complete list is available at:
From Hewlett-Packard to Agilent to Keysight. www.keysight.com/find/contactus

Americas
Canada (877) 894 4414
Brazil 55 11 3351 7010
Mexico 001 800 254 2440
United States (800) 829 4444

Asia Pacific
Australia 1 800 629 485
China 800 810 0189
Hong Kong 800 938 693
India 1 800 11 2626
Japan 0120 (421) 345
Korea 080 769 0800
Malaysia 1 800 888 848
myKeysight
Singapore 1 800 375 8100
www.keysight.com/find/mykeysight
Taiwan 0800 047 866
A personalized view into the information most relevant to you. Other AP Countries (65) 6375 8100
Keysight Nemo Solutions
Europe & Middle East
www.keysight.com/find/nemo
Austria 0800 001122
Keysight’s Nemo solutions provide testing, measurement, optimization,
Belgium 0800 58580
and analytics systems to the global wireless market based on its specialist Finland 0800 523252
sector knowledge and proprietary software and hardware products. France 0805 980333
Customers include major manufacturers of mobile devices, chipsets, and Germany 0800 6270999
network equipment, mobile network operators, regulatory authorities, and Ireland 1800 832700
independent test houses. Israel 1 809 343051
Italy 800 599100
Keysight Channel Partners Luxembourg +32 800 58580
www.keysight.com/find/channelpartners Netherlands 0800 0233200
Get the best of both worlds: Keysight’s measurement expertise and product Russia 8800 5009286
Spain 800 000154
breadth, combined with channel partner convenience.
Sweden 0200 882255
Switzerland 0800 805353
Opt. 1 (DE)
www.keysight.com/find/nemo Opt. 2 (FR)
Opt. 3 (IT)
United Kingdom 0800 0260637

For other unlisted countries:


www.keysight.com/find/contactus
(BP-9-7-17)

DEKRA Certified
ISO9001 Quality Management System

www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2015
Quality Management System

This information is subject to change without notice.


© Keysight Technologies, 2015 - 2018
Published in USA, March 19, 2018
5992-2034EN
www.keysight.com

Das könnte Ihnen auch gefallen