Beruflich Dokumente
Kultur Dokumente
8
2 9/32" 1 21/32" 3 29/32"
w=
m
3 .5m
w=
3.5
mm
G
h=
2.0
mm
650.0
25 19/32"
(Tr
eb
168.4 Scale Length m Taper Fan Brace Ends to
3.5m
le S
6 5/8" h =
m "0mm" At Ends
H 5m
w -3 .
ide
13.3 4.0 325.0 150.1 174.8
41.7
)
17/32" 34.9 5/32" 12 25/32" 5 29/32" 6 7/8"
1 21/32" 34.9 25.8
1 3/8" 1 3/8" 17.7
1 1/32" 11/16"
Depth Of Holes For Rollers Can 27.6
14.0
9/16"
Vary With Tuning Machine Mfr. 1 3/32"
Dashed Lines Indicate Outline Of The Center Joint Is One Of The Most
R 11.1 R 31.9 Tapered Ivory Nut Important Joints On The Guitar For Both
Neck Block Where It Meets The
J h=4.0mm
Top. w=3.5mm D
Top And Back Plates. Consider Using Our
5/16"
1 25/32"
Brace Diagram Plan For
45.2
15.9
Bracing Layouts
5/8"
5/32"
4.0
1 25/32"
1/2"
14 7/16"
2 1/32"
2 7/16"
2 7/16"
w=3.5mm h=4.0mm
9 9/32"
279.2
235.5
366.5
23/32"
2 1/2"
2 1/4"
2 3/8"
2 1/2"
75.3
45.1
63.5
50.8
51.8
56.9
60.0
62.0
63.4
61.8
43.9
11"
2"
5 Spaces1 @
R 24.5
12.9
1/2"
1 25/32"
Square in Profile and Taper to 0 mm At
15.9
5/8"
45.2
Each Brace End
19/32"
15.1
1/8"
3.0
7.9
5/16"
14.0
Centerlines
9/16"
21.7 14.3
89.3 27/32" 9/16"
3 17/32"
Note: At Fan Braces "F, J & K" Back Block or Butt Block. Vertical Grain
34.9 22.8 Keep Brace Profile Square Over Quarter Sawn Spruce (Same at Top
34.9 29/32" Plate)
1 3/8" w -3 . Bridge Plate. Round Top Of
)
A Rossette (Shaded) -
ide
1 3/8" L 5mm
h=3. Remainder of Brace to End
C
S
5mm
ss
(Ba
B
Cut Slots Into Headstock After Drilling Holes For Fret Wire Detail Brace Key Numbers. Refer To
m
Machine Head Rollers. Make A Template To
5m
Brace Diagram Plan For
Locate Holes And Drile Precisely With A Drill
1.7
Bracing Layouts
Press. Cut String Ramps In With A Round Rasp M
h=
and Final Shape With Sandpaper Wrapped Around
mm
A Dowel.
8. w =3
3.5
5/1 0 .5m
mh
w=
Note: Be Sure To Check The Actual Roller Spacing 6" 4.0 =3.
For Your Tuning Machines Before Making The 5/3 0m
2" m
Template and Layout. They Vary Slightly From Mfr.
To Mfr. Braces "G, H, L & M" - Round Brace
Top And Taper Braces to 0mm At
Both Ends of Braces
5
1/32"
13.0
1/2"
Tall Tentelltones Spaces 4mm Apart. These Blocks Are
Hand Placed and Shaped to Fit The Sides Before
Gluing. Also Place the Tentelltones On Top of Each
5.0 Brace End to Serve as Brace Bracket.
3/16"
482.6
19"
Interior blocking for neck and butt blocks: This wood should probably match your neck material of choice. Grain Look at www.ultimate-guitar-online.com/woodworking-hand-tools.html for hand tools required and:
should be vertical and no knots. We have and will be carrying a wide array of these accessories for your guitar www.ultimate-guitar-online.com/woodworking-power-tools.html for stationary tools recommended.
building needs.
Above all else make sure everything fits together perfectly before gluing. Do not force anything as stress is a guitar
ruins the tone. When in doubt take a few extra hours of sanding, trimming, and pre-assembly to get everything as
perfect as you can. Our Guitar Templates and Inside Forms can get you a long way down this road.