Beruflich Dokumente
Kultur Dokumente
Page : 1
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 2
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 3
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
CLASSWORK :
1. Rough ruled Long Book
2. Class Work – A3 size Drawing sketch book
3. A3 size Drawing sketch book for Assignments
4. Basic Mathematical Compass Set with Pencil, Pen , Eraser and
Sharpner and French Curves.
PRACTICALS :
1. A2 Size (Half Imperial size) Drawing Sheets (2 Nos. blank) for
every practical session
2. Calculator
3. French Curves
4. Mini- Drafter
5. Stencil (Alphabet)
6. Ruler 12”
7. Eraser, Sharper, Clutch Pencil, Leads (H, HB)
8. Butter Paper (2 nos.)
9. Drawing Clips (4 Nos.)
10. Compass Box (or set of Set Squares, Protractor)
11. Drawing sheet Container (Plastic)
CARRY YOUR ENGINEERING DRAWING MANUAL REGULARLY TO
CLASS AND PRACTICAL LAB SESSIONS.
Page : 4
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
1. Engineering Curves
Page : 5
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
NOTES:
Page : 6
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 7
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 8
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 9
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
3. Projection of Planes
CW3 : Class Work Problems
Q1. A rectangular plane ABCD ,50 mm X 70 mm size has the surface
of a plane perpendicular to the V.P. and inclined to H.P.at an angle of 30
degrees. Draw the projections of a plane if shorter side of plane is in
H.P.
Q2. A square plane ABCD with side 40 mm has its surface inclined to
V.P. at an angle of 45 degree and perpendicular to H.P. such that one of
the side of square plane is in the V.P. Draw its projections.
Q3. An isosceles triangular plate of 50 mm base and 75 mm altitude
appears as an equilateral triangle of 50 mm in top view. Draw the
projection of plate if its 50 mm long edge is on H.P.What is its
inclination with H.P.?
Q4. A circular plate of 60 mm diameter is resting on point A on its rim
with its surface inclined at 30 degree with HP. Draw projections of the
plate.
Page : 10
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 11
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
4.Projection of Solids
Page : 12
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Q7. A tetrahedron of 45 mm sides has one of its edge in the H.P. and
inclined at 450 to the V.P.The triangular plane contained by the edge of
the base in the H.P. is perpendicular to the H.P.Draw its projections
Q8 Two kids are playing with a toy which in the form of frustum of a
square pyramid whose bottom side is 6o mm and top side is of 30 mm
with axis height 70 mm .first kid held a toy in such a way that it is above
the ground and axis is inclined at 30 degree to HP and parallel to VP.
Another kid hits a toy in such a way that parallelism of axis of toy to VP
is lost and it is now inclined at 45 degree to VP but it retains its original
inclination with HP. Draw projections of toy on VP and HP.
Page : 13
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 14
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 15
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 16
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
and half of that length for other side. Draw FV, Sectional T.V. and True
shape of section .Also draw the development of lateral surface of cube
assuming major portion to be retained.
Page : 17
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
6. Orthographic Projections
CW6 : Class Work Problems
Q1 Draw FV, TV and RHSV Q2 Draw FV, TV and RHSV
Page : 18
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 19
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
3. Draw sectional FV along A-A,TV, LHSV 4. Draw Sectional FV along A-A,TV and LHSV
Page : 20
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 21
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
ACAD 7 : AutoCAD
1. Draw Sectional FV along AA, TV & LHSV
Page : 22
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 23
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
8.Isometric Views/Projections
CW8: Class Work Problems
Refer two views in given problems and construct isometric view using natural scale
Page : 24
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Refer two views in given problems and construct isometric view using natural scale
Page : 25
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 26
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 27
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 28
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Page : 29
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
3.Refer following views and draw Sectional FV along AA, Redraw TV and LHSV
Page : 30
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
Refer Following two views and draw –Sectional FV along SS,TV and LHSV
Page : 31
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
ACAD 9: AUTOCAD
1. Elevation and Plan of an object is shown in following figure. Draw -1) Sectional Elevation, section
along A-A 2) Plan 3)LHSV
NOTES:
Page : 32
F.E (All Branches) Jan. 2019 ENGINEERING DRAWING
NOTES:
Page : 33