Beruflich Dokumente
Kultur Dokumente
(For Information)
Table of Contents
Input Echo : ............................................................................................................................................................................ 3
XY Coordinate Calculations : .................................................................................................................................... 10
Internal Pressure Calculations : ........................................................................................................................... 11
External Pressure Calculations : ........................................................................................................................... 14
Element and Detail Weights : .................................................................................................................................... 16
Nozzle Flange MAWP : ....................................................................................................................................................... 18
Natural Frequency Calculation : ............................................................................................................................. 19
Wind Load Calculation : ................................................................................................................................................ 20
Earthquake Load Calculation : .................................................................................................................................. 23
Wind/Earthquake Shear, Bending : ........................................................................................................................... 24
Wind Deflection : .............................................................................................................................................................. 25
Longitudinal Stress Constants : ............................................................................................................................. 26
Longitudinal Allowable Stresses : ........................................................................................................................ 27
Longitudinal Stresses Due to . . . : ................................................................................................................. 28
Stress due to Combined Loads :................................................................................................................................ 30
Center of Gravity Calculation : ............................................................................................................................. 33
Nozzle Calcs. : N3 ............................................................................................................................................................ 34
Nozzle Calcs. : N1 ............................................................................................................................................................ 37
Nozzle Calcs. : N2 ............................................................................................................................................................ 40
Nozzle Calcs. : N4 ............................................................................................................................................................ 43
Nozzle Calcs. : N5_vent ................................................................................................................................................ 46
Nozzle Calcs. : K4_PG ..................................................................................................................................................... 49
Nozzle Calcs. : K1A .......................................................................................................................................................... 52
Nozzle Calcs. : K1B .......................................................................................................................................................... 55
Nozzle Calcs. : K2A .......................................................................................................................................................... 58
Nozzle Calcs. : K2B .......................................................................................................................................................... 61
Nozzle Calcs. : K5A .......................................................................................................................................................... 64
Nozzle Calcs. : K5B .......................................................................................................................................................... 67
Nozzle Calcs. : K3A .......................................................................................................................................................... 70
Nozzle Calcs. : K3B .......................................................................................................................................................... 73
Nozzle Schedule : .............................................................................................................................................................. 76
Nozzle Summary : ................................................................................................................................................................. 78
MDMT Summary :...................................................................................................................................................................... 79
Vessel Design Summary : ................................................................................................................................................ 80
PV Elite 2017 Licensee: PECO 3
FileName : Filter F-501AB_Calculation_rev.A
Input Echo : Step: 1 3:40pm May 2,2018
Configuration Directives:
--------------------------------------------------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
--------------------------------------------------------------------
XY Coordinate Calculations
| | | | | |
From| To | X (Horiz.)| Y (Vert.) |DX (Horiz.)| DY (Vert.) |
| | mm. | mm. | mm. | mm. |
--------------------------------------------------------------
Skirt| ... | 406.000 | ... | 406.000 |
Bottom Hea| ... | 436.000 | ... | 30.0000 |
Shell| ... | 3493.00 | ... | 3057.00 |
Top flange| ... | 3655.05 | ... | 162.052 |
50| 60| ... | 3718.55 | ... | 63.5000 |
Bottom Head
SA-403 316L, Min Metal Temp without impact per UHA-51: -196 °C
Shell
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
Please note that Nozzle, Shell, Head, Flange, etc MAWPs are all considered
when determining the hydrotest pressure for those test types that are based
on the MAWP of the vessel.
----------------------------------------------------------------------
N3 Nozzle 115.15 82.47 1.396
N1 Nozzle 117.22 114.15 1.027
N2 Nozzle 117.22 114.15 1.027
N4 Nozzle 117.22 114.15 1.027
N5_vent Nozzle 117.22 114.15 1.027
K4_PG Nozzle 117.22 114.15 1.027
K1A Nozzle 117.22 114.15 1.027
K1B Nozzle 117.22 114.15 1.027
K2A Nozzle 117.22 114.15 1.027
K2B Nozzle 117.22 114.15 1.027
K5A Nozzle 117.22 114.15 1.027
K5B Nozzle 117.22 114.15 1.027
K3A Nozzle 117.22 114.15 1.027
K3B Nozzle 117.22 114.15 1.027
----------------------------------------------------------------------
Minimum 1.027
Bottom Head
Shell
Weight of Details
Weight Summation
Note: The shipping total has been modified because some items have
been specified as being installed in the shop.
Weight Summary
| | Surface |
From| To | Area |
| | cm^2 |
----------------------------
10| 20| 2793.32 |
20| 30| 726.293 |
30| 40| 21032.4 |
40| 50| 322.673 |
50| 60| 1734.21 |
----------------------------
Total 26608.918 cm^2
Note: ANSI Ratings are per ANSI/ASME B16.5 2009 Metric Edition
The Natural Frequencies for the vessel have been computed iteratively
by solving a system of matrices. These matrices describe the mass
and the stiffness of the vessel. This is the generalized eigenvalue/
eigenvector problem and is referenced in some mathematical texts.
Input Values:
Nomenclature
Note: The Wind Loads calculated and printed in the Wind Load
calculation report have been factored by the input
scalar/load reduction factor of: 0.600.
Computed Results:
Note:
The Wind Shears/Moments and the Earthquake Shears/Moments calculated
and printed in the Wind/Earthquake Shear and Bending report have
been factored by the input Scalar/Load reductions factors of;
Wind: 0.600; Earthquake: 1.000.
Wind Deflection
| | | Hydrotest | | Hydrotest |
From| To | Tensile | Tensile | Compressive | Compressive |
| | N./mm^2 | N./mm^2 | N./mm^2 | N./mm^2 |
-------------------------------------------------------------------
10| 20| 99.0000 | 186.120 | -80.8895 | -116.602 |
20| 30| 132.000 | 186.120 | -79.3595 | -114.301 |
30| 40| 99.0000 | 186.120 | -81.7758 | -117.932 |
40| 50| 132.000 | 186.120 | -81.7758 | -117.932 |
50| 60| 132.000 | 186.120 | -88.4686 | -127.903 |
| | Wght. Str. | Wght. Str. |Wght. Str. | Wght. Str. | Wght. Str. |
From| To | Empty | Operating |Hydrotest | Emp. Mom. | Opr. Mom. |
| | N./mm^2 | N./mm^2 | N./mm^2 | N./mm^2 | N./mm^2 |
---------------------------------------------------------------------------
10| 20| -0.62899 | -0.62899 | -0.77895 | 0.72481 | 0.72481 |
20| 30| -0.69738 | -0.69738 | -0.69738 | 0.83517 | 0.83517 |
30| 40| -0.51742 | -0.51742 | -0.51742 | 0.66813 | 0.66813 |
40| 50| ... | ... | ... | ... | ... |
50| 60| ... | ... | ... | ... | ... |
| | Wght. Str. | Bend. Str. |Bend. Str. | Bend. Str. | Bend. Str. |
From| To | Hyd. Mom. | Oper. Wind |Oper. Equ. | Hyd. Wind | Hyd. Equ. |
| | N./mm^2 | N./mm^2 | N./mm^2 | N./mm^2 | N./mm^2 |
---------------------------------------------------------------------------
10| 20| 0.72481 | 4.34228 | 5.40344 | 1.43295 | ... |
20| 30| 0.83517 | 3.98739 | 4.85743 | 1.31584 | ... |
30| 40| 0.66813 | 3.13344 | 3.80914 | 1.03404 | ... |
40| 50| ... | 0.021864 | ... | 0.0072152 | ... |
50| 60| ... | 0.00007 | ... | 0.00002 | ... |
General Notes:
Critical Values:
Forces and Moments at selected elevations (not all analysis points shown):
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-403 316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
| |
| |
| |
| |
____________/| |
| \ | |
| \ | |
|____________\|__|
Note:
SA-312 TP316L, Min Metal Temp without impact per UHA-51: -196 °C
SA-312 TP316, Min Metal Temp without impact per UHA-51: -196 °C
Note: The MAWP of this junction was limited by the parent Shell/Head.
Nozzle Schedule:
For hub nozzles, the thickness and diameter shown are those of the smaller
and thinner section.
Note: The Outside projections below do not include the flange thickness.
[*] - This was a small opening and the areas were not computed or
the MAWP of this connection could not be computed because
the longitudinal bending stress was greater than the hoop stress.
Note: MAWPs (Internal Case) shown above are at the High Point.
Curve
Basic Reduced UG-20(f) Thickness Gov E*
Description MDMT MDMT MDMT ratio Thk
Notes °C °C °C mm.
----------------------------------------------------------------------------
Bottom Head [16] -196
Shell [16] -196
N3 [15] -196
N1 [15] -196
N2 [15] -196
N4 [15] -196
N5_vent [15] -196
K4_PG [15] -196
K1A [15] -196
K1B [15] -196
K2A [15] -196
K2B [15] -196
K5A [15] -196
K5B [15] -196
K3A [15] -196
K3B [15] -196
----------------------------------------------------------------------------
Required Minimum Design Metal Temperature 0 °C
Warmest Computed Minimum Design Metal Temperature -196 °C
Notes:
[ ! ] - This was an impact tested material.
[ 1] - Governing Nozzle Weld.
[ 4] - ANSI Flange MDMT Calcs; Thickness ratio per UCS-66(b)(1)(c).
[ 5] - ANSI Flange MDMT Calcs; Thickness ratio per UCS-66(b)(1)(b).
[ 6] - MDMT Calculations at the Shell/Head Joint.
[ 7] - MDMT Calculations for the Straight Flange.
[ 8] - Cylinder/Cone/Flange Junction MDMT.
[ 9] - Calculations in the Spherical Portion of the Head.
[10] - Calculations in the Knuckle Portion of the Head.
[11] - Calculated (Body Flange) Flange MDMT.
[12] - Calculated Flat Head MDMT per UCS-66.3
[13] - Tubesheet MDMT, shell side, if applicable
[14] - Tubesheet MDMT, tube side, if applicable
[15] - Nozzle Material
[16] - Shell or Head Material
Notes:
Impact test temps were not entered in and not considered in the analysis.
UCS-66(i) applies to impact tested materials not by specification and
UCS-66(g) applies to materials impact tested per UG-84.1 General Note (c).
The Basic MDMT includes the (30F) PWHT credit if applicable.
Note: Wind and Earthquake moments include the effects of user defined
forces and moments if any exist in the job and were specified
to act (compute loads and stresses) during these cases. Also
included are moment effects due to eccentric weights if any are
present in the input.
Weights:
Fabricated - Bare W/O Removable Internals 421.1 kg.
Shop Test - Fabricated + Water ( Full ) 526.8 kg.
Shipping - Fab. + Rem. Intls.+ Shipping App. 421.1 kg.
Erected - Fab. + Rem. Intls.+ Insul. (etc) 421.1 kg.
Empty - Fab. + Intls. + Details + Wghts. 421.1 kg.
Operating - Empty + Operating Liquid (No CA) 421.1 kg.
Field Test - Empty Weight + Water (Full) 526.8 kg.