Beruflich Dokumente
Kultur Dokumente
▣Features
lDetecting long distance : 0 ~ 10m
lDetectable at high illumination of sunlight
: Max. 100,000 lux
lStructure for easy connection of Sensor head
and Controller
lEasy sensitivity setting(Automatic sensitivity
setting by open push method)
lSelf-Diagnostic function
lCompact Size(W77 × L44 × H30)
▣Specifications
Model ADS-S
Detecting type Through-beam type
Detecting distance 0 ~ 10m
Power supply 12V-24VAC/DC ±10%(Ripple P-P:Max. 10%)
Power comsumption/Current AC : Max. 2VA / DC : Max. 50mA
Contact capacity : 50VDC 0.3A(Resistive load)
Contact output Contact composition : 1c
Relay life cycle : Mechanical-Min. 5,000,000 times, Electrical-Min.100,000 times
J-69
Door Side Sensor
▣Identification
(A)
lController part lSensor part Counter
1 Sensor set
Body
2
Lens
Head (B)
3 holder
Timer
Nut
4
(C)
5 Temp.
controlle
(D)
6
7 Power
controlle
1 Display LED(Red)
2 Display LED(Green)
3 Sensitivity setting button Emitter Receiver
S ensor head (E)
(Gray wires) (Blue wires)
4 Mounting hole Panel
5 Wiring connection button meter
6 Terminal for power and output(No. 1~5) ※It is able to use 2 sets of the sensor with this product.
7 Terminal for the sensor(No. 6~13) If necessary, purchase a set more.
(F)
Tacho/
Speed/
▣Dimensions Pulse
meter
lController part
77 (G)
Display
Mount ing length:70 unit
TEACH IN
A DS- S
MADE IN KOREA
OUT OU T① O UT②
N .O N .C POWER
12 -2 4VD C
12 -2 4VA C
①
Emitter(Gray )
②
Receiver(Blue)
① ② (H)
1 2 3 4 5 6 7 8 9 10 11 12 13 7B0 014B 1 2 3 4 5 Sensor
controlle
1 2 3 4 5
6 7 8 9 10 11 12 13
(I)
Proximit
lSensor part sensor
(K)
Pressur
sensor
M10× 0.75
(L)
lOption Rotary
U Sensor set U Bracket encoder
J-70
ADS-S
▣Installation
■Caution for sensor installation
1. Detecting distance is 10m.
Please install it in rated distance.
2. Please install the sensor with more than 50cm gap fromthe bottom and
ceiling. It may cause malfunction by reflected beams from the surface
of the bottom and ceiling.
3. Please don't put obstacles between emitter and receiver.
It may cause malfunction.
4. This product is for indoor. Please avoid the place where exposed in
direct sunlight or is in over rated intensity of illumination.
1. Please make a hole on the side post of auto door ! Caution For mounting hole
as follows.
U Please check the mounting holes for the head of
lWhen not using the mounting bracket
emitter and receiver are in parallel for the optical axes.
U Mounting hole of sensor head : ø12.2mm
U Please grind around the mounting holes drilled smoothly.
lWhen using the mounting bracket
It may heart by the sharp part and cause malfunction
U Through hole of sensor head : ø13 ~ ø14mm
by sensor head inclined.
U Screw hole for fixing the bracket : M4 TAP or ø3.5
2. Please mount the sensor head in the mounting hole
lWhen not using the mounting bracket
! Caution when installing in One push method
U Please check the nuts are fixed on the sensor body
U One push method
tightly.
Please insert the sensor head
U Please install that there is no gap between the nuts
into the mounting hole like the
and the side of the door(or bracket).
right picture.
It may cause malfunction because sensitivity setting
lWhen using the mounting bracket
is not available as the optical axes are not matched if
U One push method
sensor body is inclined.
①Please install the sensor head at the bracket first.
②Please fix the bracket by screws on the place for
installing.
M4 flat head cap screw ! Caution After installing the sensor head
U Please check the damage such as scratches or
pollutant on the lens of the sensor head.
It may cause malfunction in the condition of a beam
cut off or lack of sensitivity by dust.
J-71
Door Side Sensor
▣Installation
(A)
■Controller installation ! Warning When fixing controller Counter
1 2 3 4 5 6 7 8 9 10 11 12 13 7 B0 01 4B
meter
1 2 3 4 5
6 7 8 9 10 11 12 13
! Caution It may cause damag to this product. (G)
Display
unit
U Please don't connect two wires or more to a terminal.
(H)
Sensor
① ② ① ② controlle
Output(N.O)(N.C)
Emitter Receiver
Power(12-24VA C/DC)
(Gray) (Blue)
(I)
lConnection method for sensor ! Warning Connection Proximit
sensor
U Please put outer shield and inner covered wires at
once, pressing the inserting button, then take off from U It doesn't operate normally if the wiring is connected
the button. conversely.
(J)
Photo
electric
sensor
(K)
Pressur
sensor
lConnection method for power and output wires ! Warning It may cause damage to this product. (L)
Rotary
U Please put the wires pressing the terminal by a driver U Please make sure of connecting power wire to the encoder
etc.
terminal(No. 4, 5).
Otherwise, It may cause damage to this product. (M)
5-Phase
stepping
motor &
Driver &
Contr olle
J-72
ADS-S
▣Proper usage
lAfter completing sensitivity setting in using an through lCheck process for sensitivity setting failure
beam red LED is flickering, green LED is off. ①Please check obstacles between the heads of Emitter/
Only red LED displays the operation status. Receiver.
②Please check pollutant on the lens of Emitter/Receiver.
※After completing sensitivity setting in using two through
③Please check wires cut off and the connection with the
beams red LED indicates the operation status of receiver
connection diagram on the controller.
set by receiver ① and green LED indicates the operation ④Please check if the head of Emitter/Receiver is inclined
status of receiver set by receiver ②. or not.
※Self diagnostic function ⑤Please set sensitivity again after removing above
If lack of sensitivity occurs by optical axes not matched problem.
and pollution by dust on the lens of Emitter/Receiver etc.
in operation the LED of normal operation channel will be ※When sensitivity setting is failure even though above
cut off due to unstable operation. problem is solved please contact us.
J-73
Door Side Sensor
▣Operation check
Please check the operation flow chart below. (A)
Counter
Operation
(B)
Timer
LED display LED OFF LED ON(Red/Green) LED OFF LED ON(Red/Green) (C)
Temp.
U Power OFF U Normal operation U Human or material is U After human or controlle
U No human or any passing between sensors material passed
Status
material between (When through beam
sensors cut off)
(D)
Power
Relay N.O OPEN OPEN CLOSE OPEN controlle
output N.C CLOSE CLOSE OPEN CLOSE
cause mutual interference by the emitter of other output wire) long it may cause malfunction by surge
sensor. Therefore, please install them to avoid the etc. (J)
interference by exchanging the head of Emitter 7. When the lens of sensor head is polluted by dust Photo
electric
and Receiver and by keeping the distance between etc. please clean it by dried cloth slightly. sensor
the heads in more than 50cm. Do not use organic solvent like thinner.
2. When installing the sensor head on the ceiling or 8. When using switching power supply as the source
(K)
floor closely it may cause malfunction by receiving of supplying power please ground F.G terminal and Pressur
sensor
the reflected beam. Therefore, please install it by install a condenser for removing noise between 0V
keeping the suitable height(more than 50cm) from and F.G terminal as following drawing.
the ceiling or floor. (L)
Power
Switchi ng 12-24VAC
3. When the target is a translucent or small object Power Rotary
power 12-24VDC encoder
Door side sensor
(ø15mm max.) it may not detect as the light supply C(0.001 to 0.1㎌/400V)
(SMPS) : Condensor for (Controller part)
transmits them. FU G
removing noise (M)
4. When pressing the wiring of sensor in the same 5-Phase
Frame stepping
pipe laying with the high-tension wire or power motor &
Driver &
line it may cause malfunction. ※It may cause malfunction if above instructions Contr olle
are not followed.
Therefore, please use separated wiring or pipe
laying.
5. What using it in much dusty or corroded place
may cause malfunction.
Please avoid these places when installing.
J-74