Beruflich Dokumente
Kultur Dokumente
(i) TMT Corrosion resistant steel (CRS) reiforcement bar Qtl Rs.7,158.90
18.1.2 Extra over item 18.1.1(a,b,c) for each subsequent floor or part thereof Qtl Rs.37.75
above first floor level.
a) In beams and joists fitted independently without connecting plates. Qtl Rs.6,946.00
a) In beams and joists with connecting plates/ angle cleats Qtl Rs.6,729.00
b) In single stanchions (columns) composed of R.S.J. or channels with caps, Qtl Rs.7,618.00
bases, splices, angle brackets etc.
c) In trusses and trussed purlins up to 25m span and 15.0m overall height. Qtl Rs.7,316.00
18.2.3 Steel work welded in built up sections, framed work including cutting, hoisting and fixing
in positions and applying priming coat of red-lead paint including drilling holes,
supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed.
a) In beams and joists with connecting plates/ angled cleat. Qtl Rs.7,079.00
b) In trusses and trussed purlins up to 25m span and 15.0m overall height. Qtl Rs.7,320.00
18.3 ROOF TRUSS
18.3.1 Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using MS
circular hollow section conforming to relevant I.S. code, as per approved design and
drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of
red oxide Zinc Chromate primer and two coats of approved enamel paints complete
including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing
as directed.
a) TATA make Circular Hollow section- CHS of Grade YST-310 Qtl Rs.8,839.00
conforming to I.S. Specification : 1161-1998
b) Using other ISI marked approved circular hollow section Qtl Rs.8,410.00
18.3.2 Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any
two or all of the following sections (i) Square section (ii) Rectangular Hollow section of
specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including
purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts
with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist
as per design complete as directed as per specifications.
a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. Qtl Rs.9,334.00
code 4923 : 1997
b) Using other ISI marked approved brand tube Qtl Rs.9,055.00
18.4.2 Providing and fixing rolling shutters of approved make made of 80mm wide Sq.m. Rs.3,069.00
M.S. laths interlocked together through their entire lenth and jointed together
at the ends by end-locks mounted on specially designed pipe shaft with
bracket plates, guide channels and arrangements for inside and outside
locking with push-pull operation complete including cost of wire, spring and
hood cover for the shutters.
18.5.2 Providing, fitting and fixing steel windows/ ventilators (fixed) of standard Sq.m. Rs.1,554.40
rolled steel sections as per relevant I.S. Code, joints mitred and welded with
15mmx3mmx100mm lugs embedded in cement concrete block of M-10
grade including applying a coat of red-lead primer.
18.5.3 Providing, fitting and fixing steel windows of standard rolled steel sections as per
relevant I.S. Code, joints mitred and welded with 15mmx13mmx100mm lugs embedded
in cement concrete block of M-10 grade including providing and fixing of projecting
hinges (not more than 65mm and not less than 15mm wide) bolting device, steel
handles, pegs, stays of 300mm long etc. complete including providing 12mmx12mm sq.
bars duly welded to steel frame at not more than 12cm c/c applying a priming coat of
red-lead paint etc. complete as per drawing.