Beruflich Dokumente
Kultur Dokumente
16
SRI VENKATESWARA COLLEGE OF ENGINEERING
Session Teaching
Topics to be covered Ref
No * Aids
1. CPU Architecture 3,4,7 PPT
2. Bus Operations 3,4,7 PPT
3. Pipelining – Branch prediction, floating point unit 3,4,7 PPT
4. Operating Modes 3,4,7 PPT
5. Paging – Multitasking 3,4,7 PPT
6. Exception and Interrupts 3,4,7 PPT
Instruction set , Virtual Memory Concept,Virtual
7.
protection concept 3,4,7 PPT/BB
Session
Topics to be covered Ref Teaching Aids
No *
10. Arcon RISC Machine core and its Architecture 1,2 PPT
Registers and its Organization, Pipeline and
11. 1,2 PPT
Interrupts.
12. ARM processor family – Co-processors 1,2 PPT
13. ARM instruction set- 1,2 PPT/BB
14. Thumb Instruction set 1,2 PPT/BB
CAT-I - -
Unit : III
Unit Syllabus: Introduction to DSP on ARM –FIR filter – IIR filter – Discrete
Fourier transform – Exception handling – Interrupts – Interrupt handling schemes-
Firmware and boot loader – Embedded Operating systems – Integrated Development
Environment- STDIO Libraries – Peripheral Interface – Application of ARM
Processor - Caches – Memory protection Units – Memory Management units – Future
ARM Technologies.
Sessio
n Topics to be covered Ref Teaching Aids
No *
19. Introduction to DSP on ARM 1,2 PPT
FIR filter and IIR filter and Discrete Fourier
20. 1,2 PPT/BB
transform.
21. Exception handling and STDIO Libraries. 1,2 PPT
Unit : IV
Unit Syllabus: Instruction set addressing modes – operating modes- Interrupt system-
RTC-Serial Communication Interface – A/D Converter PWM and UART.
Sessio
Teaching
n Topics to be covered Ref
Aids
No *
28. Instruction set Arithmetic and Logical 5 PPT
29. Instruction set Branching and machine control instructions. 5 PPT
30. Addressing modes of 68HC11 5 PPT/BB
CAT-II
31. Operating modes 5 PPT
32. Interrupt system of 68HC11 5 PPT
33. RTC 5 PPT/BB
34. A/D Converter, PWM 5 PPT
35. UART 5 PPT
36. Serial Communication Interface 5 PPT
Unit : V
Sessio
Teaching
n Topics to be covered Ref
Aids
No *
37. PIC Microcontroller CPU Architecture 6 PPT/ICT
38. Instruction set 6 PPT
39. Interrupts of PIC Microcontroller 6 PPT/BB
40. Timers 6 PPT
41. I2C Interfacing 6 PPT
42. UART 6 PPT
43. PWM 6 PPT
44. Introduction to C Compilers 6 PPT
45. A/D Converter 6 PPT
CAT-III _ _
Content beyond syllabus covered (if any):
REFERENCES:
1. Andrew N.Sloss, Dominic Symes and Chris Wright “ ARM System Developer‟s
Guide :Designing and Optimizing System Software” , First edition, Morgan
Kaufmann Publishers, 2004.
2. Steve Furber , “ARM System –On –Chip architecture”, Addision Wesley, 2000.
3. Daniel Tabak , “Advanced Microprocessors”, Mc Graw Hill. Inc., 1995
4. James L. Antonakos , “ The Pentium Microprocessor”, Pearson Education, 1997.
5. Gene .H.Miller, “Micro Computer Engineering”, Pearson Education , 2003.
6. John .B.Peatman , “Design with PIC Microcontroller”, Prentice Hall, 1997.
7. James L.Antonakos, “An Introduction to the Intel family of Microprocessors”,
Pearson Education, 1999.
8. www.nptel.ac.in
Prepared by Approved by
Signature
Name Dr.S.Muthukumar
M.Rekha/P.Arul/S.M.Mehzabeen
Remarks *:
* If the same lesson plan is followed in the subsequent semester/year it should be
mentioned and signed by the Faculty and the HOD.