Beruflich Dokumente
Kultur Dokumente
Configuring FortiGate-200B
To change the management interface
1. Go to System > Config > Operation Mode.
NAT/Route mode 2. Enter the Management IP address and netmask that you recorded above and select
Apply.
You would typically use NAT/Route mode when the FortiGate unit is deployed as a
gateway between private and public networks. In its default NAT/Route mode configura- To configure the Primary and Secondary DNS server IP addresses
tion, the unit functions as a firewall. Firewall policies control communications through the 1. Go to System > Network > Options, enter the Primary and Secondary DNS IP address-
FortiGate unit. es that you recorded above and select Apply.
You would typically use the FortiGate unit in Transparent mode on a private network be- 1. Use the RJ-45 to DB9 serial cable to connect the FortiGate Console port to the man- STATUS
FSM
hind an existing firewall or behind a router. In its default Transparent mode configuration,
FortiGate 200B
HA
CONSOLE USB USB
POWER
the unit functions as a firewall. 2. Start a terminal emulation program (HyperTerminal) on the management computer. FortiASIC NP2 Powered
Use these settings: Baud Rate (bps) 9600, Data bits 8, Parity None, Stop bits 1, and
Web-based Manager Flow Control None.
1. Connect the FortiGate MGMT1 interface to a management computer Ethernet inter- 3. At the Login: prompt, type admin and press Enter twice (no password required).
face. Use a cross-over Ethernet cable to connect the devices directly. Use straight-
through Ethernet cables to connect the devices through a hub or switch.
NAT/Route mode
2. Configure the management computer to be on the same subnet as the MGMT1 1. Configure the FortiGate MGMT1 interface.
interface of the FortiGate unit. To do this, change the IP address of the management config system interface
computer to 192.168.1.2 and the netmask to 255.255.255.0. edit MGMT1
3. To access the FortiGate web-based manager, start a web browser and type the ad- set ip <intf_ip>/<netmask_ip>
dress http://192.168.1.99 end AC Power Required 100-240VAC, 60-50 Hz, 2-1 Amp
4. Type admin in the Name field and click Login. 2. Repeat to configure each interface, for example, to configure the Port 1 interface.
Chassis 1U
config system interface
NAT/Route mode edit port1 8 10/100 ports
... 4 10/100/1000 non-accelerated ports
To change the administrator password 3. Configure the primary and secondary DNS server IP addresses.
1. Go to System > Admin > Administrators. 4 10/100/1000 accelerated ports
config system dns Network Interfaces
2. Select Change Password for the admin administrator and enter a new password. 1 Console port
set primary <dns-server_ip>
To configure interfaces set secondary <dns-server_ip> 2 USB A
1. Go to System > Network > Interface. end 1 USB B
2. Select the edit icon for each interface to configure. 4. Configure the default gateway.
FSM slots 1 64GB SSD (not included)
3. Set the addressing mode for the interface. (See the online help for information.) config router static
• For manual addressing, enter the IP address and netmask for the interface. edit 1
set gateway <gateway_ip>
• For DHCP addressing, select DHCP and any required settings.
end
• For PPPoE addressing, select PPPoE, and enter the username and password and
any other required settings. Transparent Mode
To configure the Primary and Secondary DNS server IP addresses 1. Change from NAT/Route mode to Transparent mode and configure the Management
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP ad- IP address.
dresses that you recorded above and select Apply. config system settings
set opmode transparent
To configure a Default Gateway set manageip <mng_ip>/<netmask>
1. Go to Router > Static and select Edit icon for the static route. set gateway <gateway_ip>
2. Set Gateway to the Default Gateway IP address you recorded above and select OK. end
Transparent mode 2. Configure the DNS server IP address.
To switch from NAT/route mode to transparent mode config system dns
1. Go to System > Config > Operation Mode and select Transparent. set primary <dns-server_ip>
2. Set the Management IP/Netmask to 192.168.1.99/24. set secondary <dns-server_ip>
3. Set a default Gateway and select Apply. end © Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks of
To change the administrator password their respective holders.
Visit these links for more information and documentation for your Fortinet product:
1. Go to System > Admin > Administrators. Regulatory Compliance
Technical Documentation - http://docs.fortinet.com Fortinet Knowledge Center - http://kb.fortinet.com FCC Class A Part 15, / CE Mark
2. Select Change Password for the admin administrator and enter a new password. Technical Support - http://support.fortinet.com Training Services - http://campus.training.fortinet.com 15 June 2010 01-420-110056-20090910
Package Contents LED Description Interface Description
LED State Description Interface Type Speed Protocol Description
10/100/1000 accelerated
LEDs USB A ports
Green The unit is on. Console RJ-45 Ethernet Connection to the man-
Power agement computer.
1/2 3/4 5/6 7/8 9 / 10 11 / 12 13 / 14 15 / 16
FSM
Off The unit is off. Provides access to the
STATUS
Status
CONSOLE USB USB
POWER
(CLI).
FortiASIC NP2 Powered
REGISTER
CONSOLE USB USB
POWER
FortiASIC NP2 Powered
4 Rubber feet
FSM FSM Fortinet Storage Module.
Tools and Documenation
Straight-through RJ-45 to
Ethernet cable DB-9 Serial Cable Brackets
Ports 9 to
AC Power Cable
HDD Dummy Card Speed Green Connected at 1000Mbps. slot supports 2.5 inch solid
16
Amber Connected at 100 Mbps. state drives.