Beruflich Dokumente
Kultur Dokumente
▣Specifications
(H)
CR18-8DN CR30-15DN Sensor
Model CR18-8DP CR30-15DP CR18-8AO CR30-15AO controlle
I-38
CR Series
▣Dimensions
lCR18-8D lCR18-8A
Ø24 71.5
22 53 18.5
ø5
2,000
8
M18×1
lCR30-15D lCR30-15A
Ø42 71
35 10 55 6
ø5
2,000
5
M 30× 1.5
Unit:mm
O・C
target Nothing +12 G ND IN1 OUT1
Load
10K Load Operation
Black O・C
(Brown-Black) Return + 12 G ND IN2 OUT2
2Ω 13 14 15 16
Output voltage H
OUT2
(Black-Blue) L O UT1
OR AND
PA10-U NO R M I NV
Blue Indicator ON NO R M I NV
0V IN 1
(LED) OFF CR18-8DN N OR M
SA
IN 2 M
O
O O SB
F
D SC
F N
E
SD
PO WER A O T1
TIME O
D F
J N
T2
PNP universal output type
F
M ADE I N K OREA
5 6 7 8
NO NC
Brown
+V Detecting Presence
target Nothing NC COM NO
Load Operation 1 2 3 4
2Ω Black (Black-Blue) Return
< PA10-U >
10K Output voltage H
Load (Brown-Black) L
Blue
0V
Indicator ON ◎AC 2-wire type
(LED) OFF
Brown
Load
◎AC 2-wire type
AC
~ POWER
Brown NO NC
Load Presence
Detecting Blue
target Nothing CR18-8AO
AC
POWER ~
Operation
Load
Return
Blue
Indicator ON
(LED) OFF
I-39
Capacitive Type
▣Sensitivity adjustment
Please turn potentiometer and sequence as below procedure. (A)
Counter
q Without any target in front of the sensing head, w With a target in front of the sensing head, turn
turn the sensitivity potentiometer clockwise until the sensitivity counter clock wise from the ON
the proximity sensor turns on. position stated in 1 until the proximty sensor (B)
Timer
turns off.
(C)
Stop at ON position Stop at OFF position Temp.
controlle
e If the difference between the ON point1 and the r If you set potentiometer at center between q and
OFF point in 2 is more that 1.5turns, the sensing w , sensitivity setting will be completed. (D)
Power
operation will be stable.. controlle
It is stable when it is Adjustment completed
over 1.5 turns
(E)
Panel
meter
(H)
▣Grounding Sensor
controlle
The detecting distance will be changed by grounding status of capacitive proximity sensor and the target
[50×50×1mm(Iron)]. Please check the material when install it on panel.
(I)
Proximit
lCR18- lCR30- sensor
(K)
Pressur
sensor
(L)
Rotary
encoder
I-40
CR Series
▣Mutual-interference & Influence by surrounding metals
When several proximity sensors are mounted close together, malfunction of sensor may be caused due to
mutual interference. Therefore, be sure to provide a minimum distance between the two sensors, as below
charts.
Model
CR18 CR30
Item
A A 48 90
B 54 90
Face to Face
Parallel
When sensors are mounted on metallic panel, you must prevent the sensors from being affected by any
metallic object except target. Therefore, provide minimum distance as shown.
ℓ
Model
CR18 CR30
Item
ℓ 20 10
ød
ød 54 90
m 24 45
n 54 90
▣Materials
◎Materials of detecting targets
Detecting distance may be different by electrical characteristic of detecting target(Conductivity, Non dielectric
constant)and status of water absorption, size etc.
◎Surrounding evironment
There is water or oil on surface of detecting part, it may cause malfunction.
And if the bottle for level detecting is coated by oil etc., it may cause malfunction .
Especially 15mm type has high sensitivity for induced objects, please be sure it is not coated.
◎Oils
Do not let the 18mm sensor touch oils because the case is made of plastic.
I-41