Beruflich Dokumente
Kultur Dokumente
Basic
Sensitivity setting Setting value Current value Fine sensitivity adjustment Mode/Output *2 Preset function
Channel switch *1
*1 This is a power select switch on M8 connector types or monitor output types. Not available for 0-line types.
*2 Press and hold the [MODE] button to make advanced setting changes.
Calibration method
Workpiece Complete
* When the difference is small., "----" is displayed.
LV-N-1
Advanced
Other Calibration Methods
FS-N
Full Auto Calibration
Maximum Sensitivity Preset
The sensitivity can be automatically set while passing the workpiece through.
LV-N
This is effective when the line operation cannot be stopped. This function sets the reference condition to ".0" and correct conditions
with the slightly higher light intensity to "100.0".
Press and hold the [SET] button with no workpiece in place. While "SET" is flashing, pass a
workpiece through. (Continue pressing the [SET] button while the workpiece passes through.) This is useful when you would like to perform detection using the
Release
GV
Positioning Calibration Reflective Model * Press and hold [PRESET] to
disable this function.
: without workpiece
* Cannot be used in combination
This is effective when positioning the workpiece. with the Zero-shift function.
Press the [SET] button with no workpiece. GP-M
Place the workpiece in the location you wish to position it. Press and hold the [SET]
button for at least 3 seconds. Release the button when "SET" flashes.
Preset Common to
Thru-Beam Model / Retro-Reflective Model
With simple operation, the current value is adjusted to "100.0" at the and Reflective Model
same time as when adjusting sensitivity.
This can remove variation in detected contents or variation due to Press and hold until
"" flashes
individual difference, and is useful in predicting the need for maintenance.
LV-N-3
Advanced
Detailed Settings
FINE mode Enable the saturation of the Preset function *2
Disable the saturation of the Preset function
Normal sensitivity setting method
Percentage Calibration*2 Settings complete
Zero-shift calibration Go to system setup mode
Go to detection setup mode
Settings complete
Return to display setup mode
Go to detection setup mode
Return to normal display
FS-N
Go to display setup mode
Go to system setup mode MODE
*1 Press the button to toggle between Std/P~P_/b~b_/P_b~/P~b_.
MODE
Return to normal display *2 Press the button to set between the range of 100P and 200P.
LV-N
*1 hSP cannot be selected when LV-S31/S62/S63 is connected.
MODE
*2 You can press the button to set between the range of -99P and 99P.
System Settings LR-Z
Timer OFF
*1 Standard current value display
Settings complete
Go to display setup mode
2-output Settings*1
Go to system setup mode
Return to detection setup mode Light intensity detection mode
*2
Return to normal display Limit setting output mode *2
Warning output mode
MODE Counter output mode *3
*1 Press the button to set between the range of 1 and 9999(ms).
MODE
*2 Press the button to set the adjustment sensitivity to a range of between Timer OFF
LEu1 and LEu3 and set the warning output level to a range of between OP and Off-delay timer *4
100P. On-delay timer *4
*3 Cannot be selected when LV-S31 is connected. One-shot timer *4
MODE
*4 Press the button to toggle between oFF/oN/KEEP.
Settings complete
*5 The analog output upper limit can be set between 50 and 65535. Refer to the
"LV-N10 Series User's Manual" for the operation method of analog output in
Return to normal display
respect to the preset display.
*6 Not available for zero line types. *1 Only 2 output types (LV-N11x / N12x).
MODE
*7 Monitor output type only (LV-N11MN). *2 Press the button to select the USEr (user reset) or Auto (auto reset)
resetting methods.
*3 Select the count method from oUr1, oUr2 or Auto. When Auto is selected, the
one-shot time can be set between 1 and 9999 (ms).
MODE
*4 Press the button to set between the range of 1 and 9999(ms).