Beruflich Dokumente
Kultur Dokumente
UNIT-1: CIRCUIT CONCEPT
* 1) Explain in brief about Lumped circuit elements called resistor and
capacitor.
** 2) Write a short note on Ammeter and Voltmeter.
** 10) Define resistor. Quote all the characteristics of any resistor. If you go to
the market to purchase a resistor, apart from resistance what else will
you quote so that the safety is ensured?
* 11) Classify the controlled source and draw schematics for each.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-2: CIRCUIT ANALYSIS TECHNIQUES
*** 1) Explain WYE-DELTA transformation in brief with necessary equations and
circuit diagrams.
*** 2) Explain WYE-DELTA transformation in brief with necessary equations and
circuit diagrams.
*** 10) Determine the voltage across the 20 Ohm resistor in the following circuit
of Figure.(a) with the application of superposition theorem.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
*** 11)
Find the voltage Vx using superposition theorem. All resistor values are in
ohm.
*** 12)
For the circuit shown in following figure, use the superposition theorem
to find io.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-3: ANALOG BUILDING BLOCKS & OPAMP BASIC IDEAS
* 1) Write about Differential amplifier using Op-amp with necessary circuit
diagram and equations.
* 2) Describe band pass active filter using Operational amplifier with
necessary diagrams and equations.
*** 5) Draw an inverting amplifier and write the equation for its gain.
** 8) Describe low pass active filter using Operational amplifier with necessary
diagrams and equations.
* 11) Write about ideal operational amplifier with necessary circuit diagram
and equations.
* 14) Explain the working of a bandpass filter. Find out its bandwidth.
* 15) Design an opamp based circuit that does the following V o = V1 -2 * V2.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-4: DIGITAL BUILDING BLOCKS
* 1) For the switching function F = A(A’+B), draw a corresponding set of logic
blocks and write the truth table.
*** 2) Reduce the given function using K-map. F(A,B,C,D) = Σmi
(1,3,5,7,8,9,13,14).
*** 5) Reduce the given Boolean expression using K-map F(A,B,C) = Σm(0,2,3,5)
*** 6) Write Short note on SR flip flop with circuit diagram and truth table. (Do
all types of Flip Flops)
*** 7) Explain SR flip flop in brief. (Do all types of Flip Flops)
*** 8) Write Short note on D flip flop with circuit diagram and truth table. (Do
all types of Flip Flop)
*** 9) Write short note on JK flip flop with logic diagram and truth table. (Do all
types of Flip Flop)
*** 10) Draw an SR Flip Flop. Plot its truth table and symbol.
** 11) Draw only ISO-7 layer model block diagram of an OSI for computer
Networks.
** 12) Draw the ISO-7 layer block diagram for computer network.
* 13) Draw symbol and truth table of OR, NOT, AND and NAND gates
* 14) Draw the logic symbol and truth table of following gates.1. AND 2. OR 3.
EX-OR 4. NOR
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
** 17) Classify the types of Computer network? Explain each one of them in
brief.
* 19) For the logic expression Z = A'B + AB' (i) Obtain the truth table. (ii) Name
the operation performed (iii) Realize this operation using AND, OR, NOT
gates (iv) Realize Same operation using only NAND gates
* 23) Assign a binary code to all the 52 playing cards. Use minimum number of
bits.
* 25) Draw the block diagram of a multiplexer circuit and label the pins.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-5: SIGNAL PROCESSING
** 1) Draw only functional block diagram of signal processing system. Explain
each blocks.
** 2) Draw functional block diagram of signal processing system. Explain each
block in brief.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-6: COMMUNICATION SYSTEMS
** 1) Explain in detail Pulse modulation with necessary diagrams.
** 2) Draw block diagram of Pulse code Modulation.
*** 5) What do you understand about frequency reuse concept & Why it is used
in cellular system?
* 12) Draw neat sketch of Yagi - Uda array antenna and Explain function of
director and reflector elements.
* 14) Define the following terms: (a) Reflection (b) Directivity (c) Isotropic
Radiator
*** 16) Draw & Explain the functional description of digital communication
system in brief.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
*** 17) Draw and explain basic elements of digital communication system.
* 20) State the need of modulation and what are the other advantages of
modulation in communication system?
*** 21) What is transmission medium? What are the different types of
transmission medium?
* 22) Draw and explain the block diagram of super heterodyne AM radio
receiver.
* 23) How does a PWM signal differ from a PWM, PPM signal?
* 24) Draw the block diagram of a communication system. Explain each block.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY
Question Bank of Basic Electronics – 2110016
UNIT-7: CONTROL SYSTEMS
* 1) Explain any four rules of Block diagram reduction for control system with
necessary block diagrams.
* 2) Explain any seven rules for block diagram reduction of control system
with necessary diagram.
* 3) Draw and explain the typical unit step response (Transient Response) of
the control system.
* 10) Define control system. Classify them and state their advantages.
DARSHANINSTITUTEOFENGINEERING&TECHNOLOGY