Beruflich Dokumente
Kultur Dokumente
LOCTITE® 277
June-2004
mm
m
0.27 m
0.154
LOCTITE® 277 is designed for the permanent locking and
sealing of threaded fasteners. The product cures when 25
confined in the absence of air between close fitting metal
surfaces and prevents loosening and leakage from shock and 0
vibration. Typical applications include the locking and sealing 1min 5min10min 30min 1h 3h 6h 24h 72h
of large bolts and studs (M25 and larger). Cure Time
C
C
22°
40°
4°C
Specific Gravity @ 25 °C 1.12
Flash Point - See MSDS 50
Viscosity, Brookfield - RVT, 25 °C, mPa·s (cP):
Spindle 4, speed 20 rpm 6,000 to 8,000LMS
25
75 10964.
Bra
Ste
50
s S ate
m
el
ro
te
ch
Di
25
es
nc
inl
Zi
a
St
0
1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
TDS LOCTITE® 277, June-2004
% Initial Strength at RT
100°C
100
9
64
r7
50
1
47
or
ato
75
at
r7
tiv
tiv
ato
120°C
Ac
Ac
25
tiv
No
50
Ac
150°C
0 25
1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
0
0 1000 2000 3000 4000 5000
TYPICAL PROPERTIES OF CURED MATERIAL Hours
Physical Properties:
Coefficient of Thermal Expansion, ASTM D 696, K-1 80×10-6 Chemical/Solvent Resistance
Coefficient of Thermal Conductivity, ASTM C 177, 0.10 Aged under conditions indicated and tested @ 22 °C.
W/(m·K) % of initial strength
Specific Heat, kJ/(kg·K) 0.30
Environment °C 100 hr 500 hr 1000 hr
Motor Oil 125 100 100 100
TYPICAL PERFORMANCE OF CURED MATERIAL
Unleaded Gasoline 22 100 100 100
After 24 hours @ 22 °C
Breakaway Torque, ISO 10964: Brake fluid 22 100 100 100
M10 steel nuts and bolts N·m 32 Water Glycol 50/50 87 90 90 90
(lb.in.) (280) Acetone 22 95 95 95
Prevail Torque, ISO 10964: Ethanol 22 95 95 95
M10 steel nuts and bolts N·m 32 Sodium Hydroxide, 10% 40 100 100 70
(lb.in.) (280) Hydrochloric Acid, 10% 40 100 100 100
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
GENERAL INFORMATION
M10 steel nuts and bolts N·m 38
(lb.in.) (340) This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
Max. Prevail Torque, ISO 10964, Pre-torqued to 5 N·m: a sealant for chlorine or other strong oxidizing materials.
M10 steel nuts and bolts N·m 40
(lb.in.) (350) For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Compressive Shear Strength, ISO 10123:
Steel pins and collars N/mm² ≥9LMS Where aqueous washing systems are used to clean the
(psi) (≥1,300) surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
TYPICAL ENVIRONMENTAL RESISTANCE some cases these aqueous washes can affect the cure and
Cured for 1 week @ 22 °C performance of the adhesive.
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m: This product is not normally recommended for use on plastics
M10 zinc phosphate steel nuts and bolts (particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
Hot Strength compatibility of the product with such substrates.
Tested at temperature
100 Directions for use
For Assembly
1. For best results, clean all surfaces (external and internal)
75
% RT Strength
Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific
+860.571.5100 +49.89.9268.0 +81.45.758.1810
For the most direct access to local sales and technical support visit: www.loctite.com
TDS LOCTITE® 277, June-2004
Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific
+860.571.5100 +49.89.9268.0 +81.45.758.1810
For the most direct access to local sales and technical support visit: www.loctite.com