Beruflich Dokumente
Kultur Dokumente
Component Overview
¾Display Unit ‐ MG534
¾Computer
¾Boom Reel Assembly
¾Anti‐Two Block Switch
1
MG534 Display
Pre‐Alarm Overload Alarm
Horn Bar graph
Erected Attachment Max Capacity
& Information Actual Hookload
Parts of Line & Button
Auxiliary Head
Erected
Winches & Winch
Boom Angle
Boom Angle
Selection Button
l i
Display Brightness
Control Radius
Boom Mode Boom Length
Selection
Information &
Outrigger
Warning Bar
Configuration
Display Select Cancel Alarm
Button Operator Settable
Crane Setup Alarms
Button Stowed Fly Counterweight
MG500 Computer
Pressure
Function Kickout Fuse
Transducers
10Amp
System
Connectors
I.C.16 System Chip
Socket
2
Boom Reel Assembly
Extension
Potentiometer
Terminal
Strip
¾Using a Digital
Volt/Ohm Meter
check/set the following
voltages.
¾Check Drive Voltage for
¾Check Drive Voltage for
5vdc +/‐ .25vdc
‐DR +DR
Blue Red
3
Setting Angle Sensor Reference
Voltage
¾To set the Angle Sensor
voltage loosen the two
retaining screws on the
Angle Sensor and turn the
Angle Sensor till the correct
g ( )
voltage is achieved (.5vdc).
¾Measuring between the
Blue wire and Green wire.
‐DR Angle
Blue Green
Push down
¾To set Extension pot
voltage push down on
spring arm assembly
and turn large gear till
correct voltage is
l i
achieved (.25vdc).
Measuring between the
Blue wire and White
wire.
‐DR Extension
Blue White
4
Anti-Two Block Switch Internal
Terminal Strip
Counter‐Balanced
Weight
Proximity
Switches
System Self-Test
On initial startup the
LinkBelt Preferred screen
will appear briefly, then
the system will initiate a
self‐test which will last
approx. 7‐10 seconds.
Then the system will go
Then the system will go
to the working screen.
Crane Setup
Pressing the Crane Setup
button will initiate the
setup routine. You must
complete the entire
routine to properly setup
the system.
5
Outrigger/Tire Selection
¾ After pressing the Crane
Setup button the first
selection will be for
outrigger/tire/rigging
selection.
¾ Pressing “More” will take
you to the next selection
screen. Pressing it again
will return you to the
first screen.
Counterweight Selection
¾ The next step is to
select counterweight
options.
¾ If your machine has
you ac e as
no counterweight
options this screen
will automatically be
skipped.
¾ The boom must be fully
retracted in order to
change boom modes.
¾ If the boom is not fully
y
retracted then this
screen will be skipped.
6
Auxiliary Head Selection
¾ Select whether the
Auxiliary Head is or is not
installed on the machine
Fly Selection
¾ Select whether there is
or is not a fly erected on
the machine.
¾ If there is a fly selected
y
the next screen will ask
for the offset angle of
the fly.
¾ Select the appropriate
pick point (Main Boom,
Aux, Fly or Not Used) for
the front winch.
¾ Once the selection has
been made the screen
been made the screen
will automatically go to
the next screen.
7
Rear Winch Pick Point
¾ Select the appropriate
pick point (Main Boom,
Aux, Fly or Not Used) for
the rear winch.
¾ Notice the one less pick
point selection
point selection.
¾ Select any fly or part of
fly stowed on the side of
the boom.
¾Whenever an Operator
Settable Alarm is set there
will be a red bell appear
on the display letting you
know there is an alarm set.
¾Enter the Operator
¾Enter the Operator
Settable Alarms by
pressing the bell button
8
Operator Settable Alarms
¾ Operator Settable
Alarms main selection
screen
Boom Limits
¾ Once the machine has
been physically moved to Maximum Length
55.0
OFF
the position to set the
alarm, press the
corresponding alarm 55.0 60.0 65.4
25.0
button to set. Press
again to turn off the 60.0
Maximum Tip Height
OFF
alarm.
65.4
Maximum Angle
OFF
Minimum Angle
25.0
OFF
Swing Limits
265.0
OFF
SET
¾ Once the machine has
been physically moved to
the position to set the 95.0
265.0
alarm, press the
corresponding alarm Set both Alarms
button to set. Press again
to turn off the alarm. You
must set both limits! 95.0
OFF
SET
9
Defined Area
¾Using Length, Angle and
Swing set the machine
to the desired right or
left limit. Then press
the corresponding 97.2
button to set the alarm.
¾You must set both
limits! Right Area
Right Area
¾Anytime the boom
exceeds the limit by
either extending, angle Left Area
movement or swing the
alarm will be sounded.
¾ Pressing the Display Select
button will cause the A00 B0 C00 D00
following screen to be
displayed.
¾ Pressing the button beside
the Error Codes button will
cause the error codes to be
displayed in the white box
displayed in the white box.
¾ Pressing the button beside
the Enter Calibration will take
you to the Calibration Screen
and request you input the
calibration key sequence.
10
Calibration Security Code
Load MicroGuard 534
9.4
Calibration
1
Angle
Entry Security
72.0 Enter Correct
Radius Key Sequence
9.3 FT
Length
38.0
3
Calibration Menu
¾00 Error Codes
¾01 Crane Data
¾02 Zero Sensor
¾03 Span Sensor
¾04 Swing Pot Load
9.4 00 Error Codes
¾05 Radius/Mom Angle
72.0
¾06 Boom Defl’n Radius Menu Up
¾07 Head Angle 9.3 FT
Length Menu Down
¾08 Attachments 38.0
¾09 Winches
¾10 Rope Limits
¾11 Alarms
¾12 Digital I/O Exit
¾13 Monitor
¾14
¾15 Pressure
Think Safety!
11