Sie sind auf Seite 1von 1

pmErabRelAbnormalEnbActCdt Check any planned activities , Check high temperature on DU,RU bord also Check eNodeb alarm logs

alarm logs , also it may be do to common transport network

VoLTE_One_Pager_Retainability_CounterBased
(Cell availability)
HW and other causes Check HW issues , alarms , improper cabling , connector issues , DUS Board error
capacityUnitConnectedUsers Check "licenseCapacityConnectedUsers" of Target cell
pmHoPrepRejInLicConnUsers gracePeriodTimeLeft Also Graceperiod should be noticed to exceed the licensed capacity limits for a limited periodof timeOffload traffic from target cell
pmHoPrepRejInLicMob Audit licenseState,featurestate,servicestate & other paramter related to Intra freq & Inter freq HO feature
License issue
pmHoPrepRejInLicMultiErab Audit licenseState,featurestate,servicestate & other paramter related to MultiErabsPerUser feature
pmHoPrepRejInLicRlcUm Audit licenseState,featurestate,servicestate & other paramter related to RlcUm feature
Check these counters on target cell , Reduce no. of HO by physical opti or features (UE Level Oscillating Handover Minimization & Automated Mobility Optimization)
MP capacity of DUS is higher than DUL , to increase MP capacity DUL can be replaced by DUS
pmHoPrepRejInHighLoad (MP load control) Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
Load pmHoPrepRejInOverload (procedure latency supervision) Offload Target cell Load by changing Layering strategy, Idle mode cellreselection, connected mode mobility & Load balancing parameters
dlTransNwBandwidth , ulTransNwBandwidth Audit UE Admission Control,Bearers (SRB & DRB) Admission Control,Transport Network Admission Control & Emergency call prioritization
Admission reject pmHoPrepRejInBearerAdmissionRej zzzTemp20 , zzzTemp21 , pmRrcConnMax , pmRrcConnLevSum Physical changes (Tilt , Azimuth , height of antenna) to offload traffic from target cell
Check configuration issues (especially after new site is integrated)
(check MO ExternalEUtranCellTDD,EUtranCellRelation,TermPointToENB,TermPointToMme)
Configuration issue (also check config para ex. Activeplmnlist,PCI , TAC , EutranFrequencyRef , IP address of TermPointToENB & MME)
Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MP Baseband or RRU
eNodeB Cause
pmErabRelAbnormalEnbActHpr Auto Restart lh all llog -l (do complete eNB health checkup)
pmCellDowntimeAuto
pmErabRelAbnormalEnbActHprQci (L15B) Baseband Startup issue Baseband Trace can be used , te enable all bbmcBbOmMeSwU
Cell Down Auto pmCellDownLockAuto
(handover preparation failure)
Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
Cell down EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
Cell Down Manually pmCellDownLockMan Operation Cause manually locked during parameter change (eg. activate feature)
pmRaAttCbra
pmRaSuccCbra
pmRaFailCbraMsg2Disc
pmRaAttCfra
pmRaSuccCfra
pmRaFailCfraMsg2Disc
pmRaAllocCfra
pmRrcConnEstabAtt
pmRrcConnSucc Verify symtoms for sleeping cell
Sleeping Cell
Catch Trace(Baseband) trace from MSG1 to MSG5 , verify symtoms for sleeping cells
Power setting issue Check SectorEquipmentFunction:ConfiguredOutputPower & Eutrancelltdd:partOfSectorPower
Configuration issue
Non-access issue Idle mode parameter issue Check Eutrancelltdd MO cell selection and reselection parameters & 3G&2G cell reselection parameter/feature
Operation issues Cell Barred Check Cell Barred , acBarring for different scenarios
Alarms Check related alarms like Serviceunavailable (S1 connection failure,Hardware failure,GeneralHwError,GeneralSwError,Gigabit Ethernet Link Fault)
MME pool If MME pool is different at source and target then HO-Preparation fail will be 100%, command "get . termpointmme" can be used to find out the MME pool IPs
HO Failure Target cell Target cell is prelaunch cell.(Primaryplmnreserved)
pmHoPrepAttLteIntraFQci
IntraF Failures pmHoPrepSuccLteIntraFQci
Check Poor HO Prep Relations pmHoPrepAttLteInterFQci
IntrerF Failures pmHoPrepSuccLteInterFQci
Partial Handover Audit parameters (mainly QCI-1 related pdcpsnlength,rlcsnlength, rohc feature)
PCI confliction or confusion Audit PCI of near by sites , also check if there is overshooting cell creating conflict
maximumTransmissionPower
partOfSectorPower Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
pmBadCovEvalReport confOutputPower Physical changes (Tilt , Azimuth , height of antenna)
pmRadioTbsPwrRestricted crsGain Audit cell reselection parameters , Tune DL power related parameters (as mentioned beside)
Coverage issues pmBadCovSearchEvalReport pdschTypeBGain Check if there is scope of new site
maximumTransmissionPower
partOfSectorPower
confOutputPower
crsGain Tune related parameters (as mentioned beside) , Audit cell reselection parameters
Poor DL SINR (CQI) pmRadioUeRepCqiDistr , pmRadioUeRepCqiDistr2 pdschTypeBGain Physical optimization (Tilt , Azimuth , height of antenna) also Identify overshooting cells causing interference in DL
pmRadioRecInterferencePwr
pmRadioRecInterferencePwrPucch Check Power control parameters , Features like IRC & UL FSS can help to reduce UL interference.
pmErabRelAbnormalEnbActHo pmRadioRecInterferencePwrPrb1~100 pZeroNominalPucch Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports),VSWR alarms,Faulty TMA Connections/settings.
(handover execution failure) UL RSSI pmSinrPucchDistr , pmSinrPuschDistr pZeroNominalPusch External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc..)
eNB Triggered
Alarm need to monitor , some alarms need to monitor are VswrOverThreshold , Serviceunavailable (S1 connection failure) , Gigabit Ethernet Link Fault
Configuration issues ensure proper configuration , especially for all new site which are integrated recently
Ensure the eNodeB structure of the restart, MP Baseband or RRU
eNodeB Cause
Auto Restart lh all llog -l (do complete eNB health checkup)
pmCellDowntimeAuto
Cell Down Auto pmCellDownLockAuto Baseband Startup issue Baseband Trace can be used , te enable all bbmcBbOmMeSwU
Transport Cause S1 issues pmErabRelAbnormalEnbActTnFail check for alarms like Service Unavailable(S1 connection failure)
Cell down EPC Cause check for alarms like Service Unavailable(S1 connection failure) , Ip packet loss "above" SGW
pmCellDowntimeMan manually locked during network configuration issues ((eg. adding/changing/removing hardware)
Cell Down Manually pmCellDownLockMan Operation Cause manually locked during parameter change (eg. activate feature)
pmRaAttCbra
pmRaSuccCbra
HW issues & Alarms pmRaFailCbraMsg2Disc
pmRaAttCfra
Availability pmRaSuccCfra
pmRaFailCfraMsg2Disc
pmRaAllocCfra
pmRrcConnEstabAtt
pmRrcConnSucc Verify symtoms for sleeping cell
Sleeping Cell
Catch Trace(Baseband) trace from MSG1 to MSG5 , verify symtoms for sleeping cells
Power setting issue Check SectorEquipmentFunction:ConfiguredOutputPower & Eutrancelltdd:partOfSectorPower
Configuration issue
Non-access issue Idle mode parameter issue Check Eutrancelltdd MO cell selection and reselection parameters & 3G&2G cell reselection parameter/feature
Operation issues Cell Barred Check Cell Barred , acBarring for different scenarios
HW issues Check HW issues , alarms , improper cabling , connector issues , DUS Board error
pmErabRelAbnormalEnbActTnFail S1 or X2 interface down
(Transport issue)
Transport Resource Unavailable
maximumTransmissionPower Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
partOfSectorPower Physical changes (Tilt , Azimuth , height of antenna)
pmBadCovEvalReport confOutputPower Audit cell reselection parameters,
UL Issues: pmRadioTbsPwrRestricted crsGain Tune DL power related parameters (as mentioned beside)
Coverage issues pmBadCovSearchEvalReport pdschTypeBGain Check if there is scope of new site
pmSinrPucchDistr, pmSinrPuschDistr
maximumTransmissionPower
pmRadioTbsPwrRestricted, pmRadioTbsPwrUnrestricted
partOfSectorPower Tune related parameters (as mentioned beside).
pmTtBundlingUeSum, pmTtBundlingUeSamp, pmTtBundlingUeMax
confOutputPower Audit cell reselection parameters.
UL Packet Error, Loss Rate KPI (REfer KPI Formula from Alex)
pmRadioUeRepCqiDistr, crsGain Physical optimization (Tilt , Azimuth , height of antenna).
VoIP Integrity: pmVoipQualityUeUIOk, pmVoipQualityUeUINok
Poor DL SINR (CQI) pmRadioUeRepCqiDistr2 pdschTypeBGain Identify overshooting cells causing interference in DL.
UL Issue Harq performance: Nack rate Radio Cause
Check Power control parameters.
Features like IRC & UL FSS can help to reduce UL interference.
pmRadioRecInterferencePwr Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports).
pmRadioRecInterferencePwrPucch VSWR alarms.
pmRadioRecInterferencePwrPrb1~100 pZeroNominalPucch Faulty TMA Connections/settings.
UL RSSI pmSinrPucchDistr , pmSinrPuschDistr pZeroNominalPusch External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc).
maximumTransmissionPower Indoor coverage issue (Small cell , PICO , DOT , Hetnet)
partOfSectorPower Physical changes (Tilt , Azimuth , height of antenna)
Legend pmBadCovEvalReport confOutputPower Audit cell reselection parameters,
DL Issues: pmRadioTbsPwrRestricted crsGain Tune DL power related parameters (as mentioned beside)
pmErabRelAbnormalEnbActUeLost Coverage issues pmBadCovSearchEvalReport pdschTypeBGain Check if there is scope of new site
RF/SIP Signature (RLF drops) pmBadCovEvalReport, pmBadCovSearchEvalReport, pmCriticalBorderEvalReport
maximumTransmissionPower
If PmUeMeasurement is active, check pmUeMeasRsrpServIntraFreq1, pmUeMeasRsrqDeltaIntraFreq1
partOfSectorPower Tune related parameters (as mentioned beside).
Parameter pmRadioUeRepCqiDistr, pmRadioUeReqCqiDistr2
confOutputPower Audit cell reselection parameters.
DL Packet Error Loss rate KPI (Refer KPI Formula from Alex)
pmRadioUeRepCqiDistr, crsGain Physical optimization (Tilt , Azimuth , height of antenna).
Harq performance: Nack rate
Observation Poor DL SINR (CQI) pmRadioUeRepCqiDistr2 pdschTypeBGain Identify overshooting cells causing interference in DL.
DL Issue DL Average Latency Radio Cause
Check Power control parameters.
Action plan Features like IRC & UL FSS can help to reduce UL interference.
pmRadioRecInterferencePwr Check for Loose Connectors,Faulty Antenna(Tx & Rx antenna ports).
pmRadioRecInterferencePwrPucch VSWR alarms.
pmRadioRecInterferencePwrPrb1~100 pZeroNominalPucch Faulty TMA Connections/settings.
UL RSSI pmSinrPucchDistr , pmSinrPuschDistr pZeroNominalPusch External interference (cable tv , repeaters (due to power leak issues) , airport , police communication system etc).
HW and other causes Check HW issues , alarms , improper cabling , connector issues , DUS Board error
dlMaxRetxThreshold
Parameters RLC layer retransmissions ulMaxRetxThreshold
Other important parameters/features Multi-Target RRC Connection Re-Establishment
Features Mobility Control at Poor Coverage
If MME related issue is their many sites in the NW will be impacted & if Core related issues is there all sectors of site will be impacted.
If issue is in single sector then mostly it will be case of HW or radio related issues, Check HW issues , alarms , improper cabling , connector issues
pmErabRelMmeActEutra Check Radio Condition (low coverage , UL_Pathloss, NOISE_PUSCH/PUCCH) (refer radio cases above) also Check Traffic Volume , also check if there is sudden spike in traffic)
(Release due to Eutran generated reason) Check if multi target RRC connection reestablishment feature is functioning properly.
Check is required on both Radio & core side
If MME related issue is their many sites in the NW will be impacted & if Core related issues is there all sectors of site will be impacted.
MME Triggered If issue is in single sector then mostly it will be case of HW or radio related issues (check following) , Check HW issues , alarms , improper cabling , connector issues
Check Radio Condition (low coverage , UL_Pathloss, NOISE_PUSCH/PUCCH) (refer radio cases above) also Check Traffic Volume , also check if there is sudden spike in traffic)
pmErabRelMmeActUnspecified If there is no issue on eNB side , core team should troubleshoot the issue , Traces at core side can help to do RCA
pmErabRelMmeActUserInactivity Release due to long UE inactivity
Check for any recent UMTS RNC rehomes and make sure new UMTS Freq is defined as frequency relation under
UtranfrequencyRelation MO
pmHoPrepAttSrvcc
pmHoPrepSuccSrvcc Verify UMTS information (LAC, RNCID, UARFCN…) under ExternalUtranCellFDD matches with information in UMTS network.
pmHoExeAtt Otherwise this could lead to SRVCC preparation failures
SRVCC Failures pmHoExeSucc Check which particular UMTS cell SRVCC is being attempted and see if that UMTS cell has any performance issues or congestion
Optimize A2/B2 thresholds specific to QCI-1(a2ThresholdRsrpPrimOffset, b2Threshold1RsrpUtraOffset, b2Threshold2RscpUtraOffset)
to trigger SRVCC in optimal RF conditions on LTE and UMTS for successful handover
Check “srvcccapability” setting for UMTS neighbors, should be set to 1 (CS_ONLY_SUPPORTED)

Das könnte Ihnen auch gefallen