Beruflich Dokumente
Kultur Dokumente
DF-607
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION ........................................................................................ 5
* For particulars, see the contents of DF-607.
PC-202
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION ........................................................................................ 3
* For particulars, see the contents of PC-202.
PC-402
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION ........................................................................................ 3
* For particulars, see the contents of PC-402.
LU-201
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION ........................................................................................ 3
* For particulars, see the contents of LU-201.
i
FS-510/PU-501/OT-601
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION........................................................................................ 9
* For particulars, see the contents of FS-510/PU-501/OT-601.
FS-511/RU-502
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION........................................................................................ 7
* For particulars, see the contents of FS-511/RU-502.
SD-502
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION........................................................................................ 3
* For particulars, see the contents of SD-502.
MT-501
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION........................................................................................ 3
* For particulars, see the contents of MT-501.
JS-502
OUTLINE ........................................................................................................................ 1
COMPOSITION/OPERATION........................................................................................ 3
* For particulars, see the contents of JS-502.
ii
SAFETY AND IMPORTANT WARNING ITEMS
IMPORTANT NOTICE
Because of possible hazards to an inexperienced person servicing this product as well as
the risk of damage to the product, Konica Minolta Business Technologies, INC. (hereafter
called the KMBT) strongly recommends that all servicing be performed only by KMBT-
trained service technicians.
Changes may have been made to this product to improve its performance after this Service
Manual was printed. Accordingly, KMBT does not warrant, either explicitly or implicitly, that
the information contained in this Service Manual is complete and accurate.
The user of this Service Manual must assume all risks of personal injury and/or damage to
the product while servicing the product for which this Service Manual is intended.
Therefore, this Service Manual must be carefully read before doing service work both in the
course of technical training and even after that, for performing maintenance and control of
the product properly.
Keep this Service Manual also for future service.
Symbols used for safety and important warning items are defined as follows:
S-1
SAFETY AND IMPORTANT WARNING ITEMS
SAFETY WARNINGS
[1] MODIFICATIONS NOT AUTHORIZED BY KONICA MINOLTA
BUSINESS TECHNOLOGIES, INC.
Konica Minolta brand products are renowned for their high reliability. This reliability is
achieved through high-quality design and a solid service network.
Product design is a highly complicated and delicate process where numerous mechanical,
physical, and electrical aspects have to be taken into consideration, with the aim of arriving
at proper tolerances and safety factors. For this reason, unauthorized modifications involve
a high risk of degradation in performance and safety. Such modifications are therefore
strictly prohibited. The points listed below are not exhaustive, but they illustrate the reason-
ing behind this policy.
Prohibited Actions
DANGER
• Using any cables or power cord not specified by KMBT.
S-2
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Use power supply cord set which meets the following
criteria:
AC230V
- provided with a plug having configuration intended for
the connection to wall outlet appropriate for the prod-
uct's rated voltage and current, and
- the plug has pin/terminal(s) for grounding, and
- provided with three-conductor cable having enough cur-
rent capacity, and
AC208V 240V
- the cord set meets regulatory requirements for the area.
Use of inadequate cord set leads to fire or electric shock.
• Attach power plug which meets the following criteria:
- having configuration intended for the connection to wall
outlet appropriate for the product's rated voltage and
current, and
- the plug has pin/terminal(s) for grounding, and
- meets regulatory requirements for the area.
Use of inadequate cord set leads to the product connect-
ing to inadequate power supply (voltage, current capac-
ity, grounding), and may result in fire or electric shock.
S-3
SAFETY AND IMPORTANT WARNING ITEMS
1. Power Supply
WARNING
• Check that mains voltage is as specified.
Connection to wrong voltage supply may result in fire or
electric shock. ?V
• Plug the power cord into the dedicated wall outlet with a
capacity greater than the maximum power consumption.
If excessive current flows in the wall outlet, fire may
result.
S-4
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Check whether the product is grounded properly.
If current leakage occurs in an ungrounded product, you
may suffer electric shock while operating the product.
Connect power plug to grounded wall outlet.
WARNING
• When using the power cord set (inlet type) that came with
this product, make sure the connector is securely inserted
in the inlet of the product.
When securing measure is provided, secure the cord with
the fixture properly.
If the power cord (inlet type) is not connected to the prod-
uct securely, a contact problem may lead to increased
resistance, overheating, and risk of fire.
S-5
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Check whether dust is collected around the power plug
and wall outlet.
Using the power plug and wall outlet without removing
dust may result in fire.
• Do not insert the power plug into the wall outlet with a wet
hand.
The risk of electric shock exists.
• When unplugging the power cord, grasp the plug, not the
cable.
The cable may be broken, leading to a risk of fire and
electric shock.
Wiring
WARNING
• Never use multi-plug adapters to plug multiple power
cords in the same outlet.
If used, the risk of fire exists.
S-6
SAFETY AND IMPORTANT WARNING ITEMS
2. Installation Requirements
WARNING
• Do not place the product near flammable materials or vol-
atile materials that may catch fire.
A risk of fire exists.
WARNING
• When the product is not used over an extended period of
time (holidays, etc.), switch it off and unplug the power
cord.
Dust collected around the power plug and outlet may
cause fire.
Ventilation
CAUTION
• The product generates ozone gas during operation, but it
will not be harmful to the human body.
If a bad smell of ozone is present in the following cases,
ventilate the room.
a. When the product is used in a poorly ventilated room
b. When taking a lot of copies
c. When using multiple products at the same time
Fixing
CAUTION
• Be sure to lock the caster stoppers.
In the case of an earthquake and so on, the product may
slide, leading to a injury.
S-7
SAFETY AND IMPORTANT WARNING ITEMS
CAUTION
• Before conducting an inspection, read all relevant docu-
mentation (service manual, technical notices, etc.) and
proceed with the inspection following the prescribed pro-
cedure in safety clothes, using only the prescribed tools.
Do not make any adjustment not described in the docu-
mentation.
If the prescribed procedure or tool is not used, the prod-
uct may break and a risk of injury or fire exists.
WARNING
• Take every care when making adjustments or performing
an operation check with the product powered.
If you make adjustments or perform an operation check
with the external cover detached, you may touch live or
high-voltage parts or you may be caught in moving gears
or the timing belt, leading to a risk of injury.
S-8
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• Check the exterior and frame for edges, burrs, and other
damages.
The user or CE may be injured.
S-9
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• When replacing a lithium battery, replace it with a new lith-
ium battery specified in the Parts Guide Manual. Dispose
of the used lithium battery using the method specified by
local authority.
Improper replacement can cause explosion.
• Make sure the wiring cannot come into contact with sharp
edges, burrs, or other pointed parts.
Current can leak, leading to a risk of electric shock or
fire.
• Make sure that all screws, components, wiring, connec-
tors, etc. that were removed for safety check and mainte-
nance have been reinstalled in the original location. (Pay
special attention to forgotten connectors, pinched cables,
forgotten screws, etc.)
A risk of product trouble, electric shock, and fire exists.
Handling of Consumables
WARNING
• Toner and developer are not harmful substances, but care
must be taken not to breathe excessive amounts or let the
substances come into contact with eyes, etc. It may be
stimulative.
If the substances get in the eye, rinse with plenty of water
immediately. When symptoms are noticeable, consult a
physician.
S-10
SAFETY AND IMPORTANT WARNING ITEMS
Handling of Consumables
WARNING
• Never throw the used cartridge and toner into fire.
You may be burned due to dust explosion.
CAUTION
• Unplug the power cord from the wall outlet.
Isopropyl alcohol and acetone are highly flammable and
must be handled with care. A risk of fire exists.
S-11
SAFETY INFORMATION
SAFETY INFORMATION
IMPORTANT NOTICE
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Admin-
istration implemented regulations for laser products manufactured since August 1, 1976.
Compliance is mandatory for products marketed in the United States.
This copier is certified as a "Class 1" laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. Since radiation emit-
ted inside this copier is completely confined within protective housings and external covers,
the laser beam cannot escape during any phase of normal user operation.
S-12
SAFETY INFORMATION
50gap0e001na
S-13
SAFETY INFORMATION
50gap0e002na
CAUTION:
• You may be burned or injured if you touch any area that you are advised by any
caution label to keep yourself away from. Do not remove caution labels. And also,
when the caution label is peeled off or soiled and cannot be seen clearly, replace
it with a new caution label.
S-14
MEASURES TO TAKE IN CASE OF AN ACCIDENT
S-15
MEASURES TO TAKE IN CASE OF AN ACCIDENT
Blank Page
S-16
Composition of the service manual
This service manual consists of the following sections and chapters:
This section gives, as information required by the CE at the site (or at the customer's
premise), a rough outline of the service schedule and its details, maintenance steps, the
object and role of each adjustment, error codes and supplementary information.
The details of items with an asterisk "*" are described only in the service manual of
the main body.
C-1
Notation of the service manual
A. Product name
In this manual, each of the products is described as follows:
B. Brand name
The company names and product names mentioned in this manual are the brand name or
the registered trademark of each company.
C-2
Classification Load symbol Ex. of signal name Description
24V Power to drive the motor
CONT Drive signal
DRV1
Motor M
DRV2
Drive signals of two kinds
D1
D2
_U
_V
_W
Drive signals (control signals) of three kinds
DRV1
DRV2
DRV3
D1
D2
D3
D4
DRV A
DRV A
DRV B Drive signals (control signals) of four kinds
DRV B Motor, phases A and B control signals
A
Motor M /A
B
/B
AB
BB
CLK, PLL PLL control signal
LCK, Lock, LD PLL lock signal
FR Forward/reverse rotation signal
EM, Lock, LCK, LD Motor lock abnormality
BLK Drive brake signal
P/S Power/stop
S/S
Operating load start/stop signal
SS
CW/CCW, F/R Rotational direction switching signal
ENB Effective signal
TEMP_ER Motor temperature abnormality detection signal
24V Power to drive the fan motor
CONT, DRIVE Drive signal
Fan FM
HL Speed control signal (2 speeds)
EM, Lock, LCK, FEM Detection signal
Others TH1.S, ANG Analog signal
C-3
Classification Load symbol Ex. of signal name Description
SG, S.GND, S_GND Signal ground
Ground
PG, P.GND Power ground
DCD Data carrier detection
SIN Serial input
SOUT Serial output
DTR Data terminal operation available
GND Signal ground (earth)
Serial com-
DSR, DSET Data set ready
munication
RTS Transmission request signal
CTS Consent transmission signal
RI Ring indicator
TXD Serial transmission data
RXD Serial reception data
<Example>
C-4
SERVICE MANUAL Theory of Operation
500/420/360
Main body
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
bizhub 500/420/360
bizhub 500/420/360
OUTLINE
1. SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. PRODUCT SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. UNIT CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. PAPER PATH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
COMPOSITION/OPERATION
5. OVERALL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Time chart when the power is turned ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2 Control block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6. SCANNER SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.2 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.3.1 Scan/exposure lamp control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.3.2 Original size detection control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.3.3 AE control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.3.4 Image processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. WRITE SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.2.1 Laser beam path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.2.2 Write control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.2.3 Image stabilization control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.2.4 Image processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8. PHOTO CONDUCTOR SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.2 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.2.1 Drum drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.2.2 Drum claw drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.3.1 Image creation control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.3.2 Drum claw control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8.3.3 Image stabilization control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9. CHARGING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2.1 Charging control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9.2.2 Erase lamp (EL) control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
10. TRANSFER/SEPARATION SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.2.1 Transfer guide control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.2.2 Transfer/separation control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
ii
Theory of Operation Ver.2.0 Jan. 2007 CONTENTS
16.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
bizhub 500/420/360
16.3.1 Loop control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
17. ADU SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
17.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
17.2 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
17.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
17.3.1 Conveyance path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
17.3.2 Conveyance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
18. FUSING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
18.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
18.2 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
18.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
18.3.1 Fusing roller drive control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
18.3.2 Web drive control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
18.3.3 Fusing temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
18.3.4 Fusing roller edge cooling control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
18.3.5 Envelope conveyance mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
18.3.6 Protection against abnormality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
18.3.7 Jam detection control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
19. REVERSE/EXIT SECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
19.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
19.2 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
19.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
19.3.1 Conveyance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
19.3.2 Reverse control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
20. INTERFACE SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
20.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
20.2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
21. IMAGE STABILIZATION CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
21.1 Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
21.2 Operation flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
21.2.1 Image stabilization control flow when the power switch (SW2) is turned ON . . . . . . . . . . . . . . . 83
21.2.2 Image stabilization control flow while in the print and the idle . . . . . . . . . . . . . . . . . . . . . . . . . . 86
22. IMAGE PROCESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
22.1 Image processing in the scanner section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
22.1.1 Shading correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
22.1.2 AE control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
22.1.3 Area discrimination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
22.1.4 Brightness/density conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
22.1.5 Filter/magnification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
22.1.6 Scanner gamma correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
22.1.7 Halftone processing (error diffusion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
22.1.8 Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
22.1.9 Storage of image data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
22.2 Image processing in the write section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
23. OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
23.1 Fan control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
23.1.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
23.1.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
23.2 Counter control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
iii
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
iv
Theory of Operation Ver.2.0 Jan. 2007 1. SYSTEM CONFIGURATION
OUTLINE
bizhub 500/420/360
1. SYSTEM CONFIGURATION
A. System configuration
[5]
[1] [6]
[2] [7]
[3] [8]
[4] [9]
[22]
[21]
[20]
[19] [11]
[14]
[17] [15]
[18]
[10] [12]
[16]
[10] [13]
50gat1e001nb
*1 See "6.4 Option counter" in Field Service bizhub 500/420/360 main body for details.
*2 Dehumidifier heater is set up as service part.
*3 Swedish punch kit G is for Europe only.
1 1
1. SYSTEM CONFIGURATION Theory of Operation Ver.2.0 Jan. 2007
Note
• Any combination other than those listed below is not available.
2
Theory of Operation Ver.2.0 Jan. 2007 2. PRODUCT SPECIFICATIONS
2. PRODUCT SPECIFICATIONS
bizhub 500/420/360
A. Type
3
2. PRODUCT SPECIFICATIONS Theory of Operation Ver.2.0 Jan. 2007
B. Functions
bizhub 500/420/360
4 1
Theory of Operation Ver.2.0 Jan. 2007 2. PRODUCT SPECIFICATIONS
C. Type of paper
bizhub 500/420/360
Plain paper *1 All trays High quality paper of 60 to 90 g/m2
Special paper *2 Bypass feed only OHP film, label paper *3, blueprint master paper *3
High quality paper of 50 to 59 g/m2 (thin paper)
All trays High quality paper of 91 to 105 g/m2 (thick paper)
Bypass feed only High quality paper of 106 to 210 g/m2 (thick paper)
D. Maintenance
E. Machine data
1 5
2. PRODUCT SPECIFICATIONS Theory of Operation Ver.2.0 Jan. 2007
F. Operating environment
bizhub 500/420/360
Temperature 10 to 30 °C
Humidity 10 to 80%RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
6
Theory of Operation Ver.2.0 Jan. 2007 3. UNIT CONFIGURATION
3. UNIT CONFIGURATION
bizhub 500/420/360
[17]
[1]
[2]
[16]
[15] [3]
[14]
[4]
[5]
[13]
[6]
[12]
[7]
[8]
[11]
[9]
[10]
50gat1c002na
7
4. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
4. PAPER PATH
bizhub 500/420/360
[1]
[9]
[8]
[7]
[2]
[6]
[3]
[5] [4]
50gat1c003na
8
Theory of Operation Ver.2.0 Jan. 2007 5. OVERALL CONFIGURATION
COMPOSITION/OPERATION
bizhub 500/420/360
5. OVERALL CONFIGURATION
5.1 Time chart when the power is turned ON
Item
Normal
Scanner motor rotation
(M2) Reverse
rotation
Exposure lamp (L1)
Fusing heater lamp /1 (L2)
Fusing heater lamp /2 (L3)
Fusing motor (M11)
Drum motor (M1)
Developing motor (M3)
Polygon motor (M5)
Laser (LDB)
Paper lift motor /1 (M7)
Upper limit sensor /1 (PS6)
Paper lift motor /2 (M8)
Upper limit sensor /2 (PS13)
50gat2e001na
[1] Fusing heater lamps /1 (L2) and /2 (L3) turn [5] Drum motor (M1) turns ON
ON early [6] Dot diameter adjustment starts
[2] Power switch (SW2) turns ON [7] The fusing temperature gets to the pre-
[3] Initial communication between the overall scribed temperature to start the preliminary
control board (OACB) and the printer control rotation for fusing
board (PRCB) [8] Dot diameter adjustment completed
[4] Shading correction [9] Warming up completed
Note
• Each operation varies according to the setting of the software DipSW in the service mode.
• The power is turned ON with DF closed.
• The power is turned ON with the lift plate of the tray down.
9
5. OVERALL CONFIGURATION Theory of Operation Ver.2.0 Jan. 2007
OACB
SC
Write
Section DF
M FM CL SD PS
PRCB
SDB DCPU HV
M PS
JS LU PC FS, RU
10
Theory of Operation Ver.2.0 Jan. 2007 6. SCANNER SECTION
6. SCANNER SECTION
bizhub 500/420/360
6.1 Composition
CCD unit
Mirror unit (CCDB)
Exposure unit
Shading
correction
plate
50gat2c001na
6.2 Drive
[4]
[3]
[5]
[1]
[2]
50gat2c002na
11
6. SCANNER SECTION Theory of Operation Ver.2.0 Jan. 2007
6.3 Operation
bizhub 500/420/360
[2] [1]
[3]
[6]
[4]
[5]
50gat2c034na
[2] [1]
[3]
[6]
[4]
[5]
50gat2c035na
12
Theory of Operation Ver.2.0 Jan. 2007 6. SCANNER SECTION
bizhub 500/420/360
For the original read mode, the following two types are available: the platen mode and the DF mode. While in the
platen mode, the exposure unit scans the original for reading. And while in the DF mode, since DF conveys the
original, the exposure unit remains at the prescribed position (DF read position) to read the original.
[5]
[6]
[7]
[8]
50gat2c037na
[5]
[6]
[7]
50gat2c036na
Note
• When the tray 1 is selected by manual, not by APS, no shading correction is made.
13
6. SCANNER SECTION Theory of Operation Ver.2.0 Jan. 2007
[4]
[5]
[6]
50gat2c038na
14
Theory of Operation Ver.2.0 Jan. 2007 6. SCANNER SECTION
bizhub 500/420/360
A. Detection method
The original size detection method varies for the DF mode and the platen mode.
(1) DF mode
See DF-607 Service Manual.
*1 No discrimination is made between 81/2 x 14 and 81/2 x 11S. When the size is 81/2 x 14, this is detected as
81/2 x 11S.
B. Detection timing
(1) Platen mode (while in DF closed)
When the APS timing sensor (PS31) turns on while in DF closed, the original size is detected.
15
6. SCANNER SECTION Theory of Operation Ver.2.0 Jan. 2007
6.3.3 AE control
bizhub 500/420/360
When AE is selected, the density level of the original is detected to adjust it to an appropriate density automati-
cally. The sampling range of the original density in the AE control varies for the platen mode and the DF mode.
[5]
[1]
[7]
[6]
[5]
[2] [2]
[4]
[3]
50gat2c039na
[4]
[1]
[6]
[5]
[4]
[3] [2]
50gat2c040na
16
Theory of Operation Ver.2.0 Jan. 2007 6. SCANNER SECTION
bizhub 500/420/360
The following items are provided for the image processing. For details, See "22. IMAGE PROCESSING".
• AOC (Auto offset control)
• AGC (Auto gain control)
• Shading correction
• AE processing
• Range discrimination
• Brightness/density conversion
• Filter/magnification
• Density gamma (conversion)
• Halftone processing (error diffusion)
• Skew adjustment
• Compression
• Storage of image data
17
7. WRITE SECTION Theory of Operation Ver.2.0 Jan. 2007
7. WRITE SECTION
bizhub 500/420/360
7.1 Composition
18
Theory of Operation Ver.2.0 Jan. 2007 7. WRITE SECTION
7.2 Operation
bizhub 500/420/360
7.2.1 Laser beam path
[10]
[9]
[8]
[7] [1]
[6]
[2]
[5]
[3]
[4]
50gat2c041na
19
7. WRITE SECTION Theory of Operation Ver.2.0 Jan. 2007
The following items are provided for the image processing. For details, See "22.2 Image processing in the write
section".
• Rotation/elongation
• 2 dots PWM
• PWM
• Frequency conversion
20
Theory of Operation Ver.2.0 Jan. 2007 8. PHOTO CONDUCTOR SECTION
bizhub 500/420/360
8.1 Composition
50gat2c004na
21
8. PHOTO CONDUCTOR SECTION Theory of Operation Ver.2.0 Jan. 2007
8.2 Drive
bizhub 500/420/360
[1]
[2]
50gat2c005na
[1]
[2]
50gat2c006na
22
Theory of Operation Ver.2.0 Jan. 2007 8. PHOTO CONDUCTOR SECTION
8.3 Operation
bizhub 500/420/360
8.3.1 Image creation control
When the print start signal turns ON [1], various motors turn ON to place each unit in the operating condition. At
the same time, the erase lamp (EL) turns ON to neutralize the drum and the charging corona charges the drum.
A specified period of time after the print start signal turns ON, the developing bias turns ON [2] and then a high
voltage is impressed [3] on the guide plate. When the preparation for image creation is made, an image is cre-
ated on the drum surface by laser irradiation and developing.
A specified period of time after the registration clutch (CL1) turns ON [4], a high voltage is impressed on the
transfer corona [5] and the separation corona [6] to turn ON the transfer exposure lamp (TSL) [8] and the drum
claw solenoid (SD2) [9] sequentially. The ON timing [7] of TSL varies according to the type of paper. And the ON
time period of TSL also varies according to the setting environment. An image created on the drum is transferred
onto paper and then the paper is separated from the drum.
A specified period of time after the registration sensor (PS1) detects the trailing edge of paper and turns OFF
[10], each operation turns OFF. However, some operations turn OFF a specified period of time after PS1 detects
the trailing edge of the last paper and turns OFF [11], or a specified period of time after the fusing exit sensor
(PS3) detects the trailing edge of the last paper and turns OFF [13]. For the charging corona, the developing bias
and the guide plate bias, with the OFF timing [12] by the last paper of the transfer corona used as a starting
point, each of the OFF timing is interlocked.
[13]
[7] [8] [9] [12] 50gat2c103na
[1] Print start signal ON [8] Transfer exposure lamp (TSL) ON (This var-
[2] Developing bias high voltage impressed ies according to the setting environment.)
[3] Guide plate bias high voltage impressed [9] Drum claw solenoid (SD2) ON
[4] Registration clutch (CL1) ON [10] Trailing edge of the 1st paper detected
[5] Transfer corona high voltage impressed [11] Trailing edge of the last paper detected
[6] Separation corona high voltage impressed [12] Transfer of the last paper OFF
[7] Varies according to the type of paper. [13] Trailing edge of the last paper detected
23
8. PHOTO CONDUCTOR SECTION Theory of Operation Ver.2.0 Jan. 2007
A. Purpose
Two drum claws are employed to prevent paper from winding up around the drum (winding-up jam). The contact
and severance of the drum claws to and from the drum are made by the ON/OFF of the drum claw solenoid
(SD2).
B. Swing operation
To prevent paper from getting stained at specific points and the drum [3] from being damaged, the drum claw [2]
makes a swing operation of about 7 mm against the drum surface.
The drum claw unit [4] is provided with a projection [7]. This projection is pressed by the cam [6] provided on the
gear [5] to push out the drum claw unit backward. When the gear rotates to release the cam, the drum claw unit
is sent back to the original position by the spring [1]. This operation is repeated to swing the drum claw.
24
Theory of Operation Ver.2.0 Jan. 2007 9. CHARGING SECTION
9. CHARGING SECTION
bizhub 500/420/360
9.1 Composition
50gat2c007na
9.2 Operation
9.2.1 Charging control
A. Charging wire
The high voltage unit (HV) pressurizes 24V DC to impress a minus (–) DC voltage on the charging wire for dis-
charge.
Charging output range: –500 to –1100 µA
B. Charging grid
To obtain a uniform charging wire discharge, a minus (–) high voltage is impressed from the high voltage unit (HV)
to the charging grid.
Charging grid voltage output range: –450 to –1090 V
B. Execution timing
The erase lamp (EL) turns ON in synch with the print start signal turning ON. And it turns OFF a specified period
of time after the fusing exit sensor (PS3) detects the trailing edge of the last paper.
25
10. TRANSFER/SEPARATION SECTION Theory of Operation Ver.2.0 Jan. 2007
10.1 Composition
26
Theory of Operation Ver.2.0 Jan. 2007 10. TRANSFER/SEPARATION SECTION
10.2 Operation
bizhub 500/420/360
10.2.1 Transfer guide control
A. Purpose
To prevent the transfer guide plate from getting stained, a minus (–) DC voltage is impressed from the high volt-
age unit (HV).
Voltage impressed: –500 V
B. Execution timing
The impression of a voltage onto the transfer guide plate is made ON a specified period of time after the devel-
oping bias turns ON. And it turns OFF a specified period of time after the developing bias turns OFF.
B. Separation
For separation, an AC high voltage and a minus (–) DC voltage are employed. The high voltage unit (HV)
impresses a voltage onto the separation wire for discharging.
Separation AC output range: 300 to 1000 µA
Separation DC output range: 0 to –200 µA
B. Execution timing
The transfer exposure lamp (TSL) turns ON a specified period of time after the registration clutch (CL1) turns ON.
And it turns OFF a specified period of time after the registration sensor (PS1) turns OFF.
27
11. DEVELOPING UNIT Theory of Operation Ver.2.0 Jan. 2007
11.1 Composition
28
Theory of Operation Ver.2.0 Jan. 2007 11. DEVELOPING UNIT
11.2 Drive
bizhub 500/420/360
[6]
[5]
[4]
[1]
[3]
[2]
50gat2c010na
29
11. DEVELOPING UNIT Theory of Operation Ver.2.0 Jan. 2007
11.3 Operation
bizhub 500/420/360
[1]
[2]
50gat2c043na
30
Theory of Operation Ver.2.0 Jan. 2007 11. DEVELOPING UNIT
bizhub 500/420/360
A. Purpose
To make toner get easily attached to the drum while in developing, a developing bias is impressed onto the
developing roller [1].
[1]
50gat2c044na
B. Timing
To prevent unnecessary carriers from attaching to the drum, a developing bias turns ON a specified period of
time after the print start signal turns ON, and it turns OFF a specified period of time after charging turns OFF.
31
11. DEVELOPING UNIT Theory of Operation Ver.2.0 Jan. 2007
A. Purpose
To prevent the splash of toner from the developing roller, the duct [4] is provided at 2 places of the developing
unit [1]. Toner guided into the duct is sucked in by the developing suction fan (FM6) [3] to be collected by the
suction filter /A [2].
[3]
[4]
[2]
[1]
50gat2c045na
32
Theory of Operation Ver.2.0 Jan. 2007 12. TONER SUPPLY SECTION
bizhub 500/420/360
12.1 Composition
Toner bottle
50gat2c011na
33
12. TONER SUPPLY SECTION Theory of Operation Ver.2.0 Jan. 2007
12.2 Drive
bizhub 500/420/360
[5]
[4]
[1]
[2]
[3]
50gat2e003na
34
Theory of Operation Ver.2.0 Jan. 2007 12. TONER SUPPLY SECTION
12.3 Operation
bizhub 500/420/360
12.3.1 Toner level detection control
A. Toner level detection control
Toner remaining in the toner hopper is detected by the toner remaining sensor (PZS). When toner remaining in
the hopper is found below the prescribed amount, a toner supply signal is issued to the printer control board
(PRCB). This signal is transmitted to the operation board (OB) through the overall control board (OACB). Accord-
ingly, OB displays a message in LCD on the LCD board (LCDB).
B. Detection timing
• At all times while in printing.
B. While in printing
While in printing, the toner density is detected by the TCR sensor (TCRS). The ON time periods of the toner sup-
ply motor (M4) and the toner solenoid (SD5) are decided according to the output voltage of TCRS to supply
toner from the toner hopper to the developing unit.
35
12. TONER SUPPLY SECTION Theory of Operation Ver.2.0 Jan. 2007
A. Purpose
To convey toner in the toner bottle to the toner hopper.
B. Operation
The exit [1] of the toner bottle is normally closed. However, by setting the bottle to the toner supply section, the
accordion section is pushed and compressed to let the exit open. A bottle set to the toner supply section
rotates when the toner bottle motor (M10) turns ON. When the toner bottle rotates, toner is conveyed to the exit
of the bottle along the spiral groove engraved on the surface of the toner bottle and flows out into the toner hop-
per.
[1]
D C B A
[2]
D C B
A
50gat2e002na
36
Theory of Operation Ver.2.0 Jan. 2007 13. CLEANING/TONER RECYCLE SECTION
bizhub 500/420/360
13.1 Composition
50gat2c013na
37
13. CLEANING/TONER RECYCLE SECTION Theory of Operation Ver.2.0 Jan. 2007
13.2 Drive
bizhub 500/420/360
[1]
[2]
[3]
50gat2c014na
38
Theory of Operation Ver.2.0 Jan. 2007 13. CLEANING/TONER RECYCLE SECTION
13.3 Operation
bizhub 500/420/360
13.3.1 Cleaning operation
Toner scraped by the cleaning blade [4] is neutralized by the neutralizing sheet [2], then collected by the collec-
tion paddle [1], and finally guided to the collection screw [5]. At this time, toner remaining on the collection pad-
dle is scraped by the scraper [6].
[5] [6]
[1]
[4]
[3]
[2]
50gat2c047na
B. Execution timing
The collection paddle to be used to collect toner is driven by the drum motor (M1) and the toner collection oper-
ation is made in synch with the ON/OFF of M1.
B. Execution timing
The collection screw is driven by the drum motor (M1) and the toner conveyance operation is made in synch
with the ON/OFF of M1.
39
14. PAPER FEED SECTION (Tray 1/2) Theory of Operation Ver.2.0 Jan. 2007
14.1 Composition
14.1.1 Tray 1
Pick-up roller
Lift plate Feed roller
Separation roller
Tray 1
50gat2c015na
14.1.2 Tray 2
Feed roller
Lift plate
Separation roller
Tray 2
50gat2c104na
40
Theory of Operation Ver.2.0 Jan. 2007 14. PAPER FEED SECTION (Tray 1/2)
14.2 Drive
bizhub 500/420/360
14.2.1 Paper feed drive
[1]
[13]
[12] [2]
[3]
[4]
[5]
[6]
[7]
[11] [10]
[8]
[9]
50gat2c016na
[3][4]
[1]
[2] 50gat2c017na
41
14. PAPER FEED SECTION (Tray 1/2) Theory of Operation Ver.2.0 Jan. 2007
14.3 Operation
bizhub 500/420/360
[9][10]
[1]
[4] [5]
C. Operation timing
When the tray is set, the tray set sensors /1 (PS8) and /2 (PS14) turn ON. In this way, the paper lift motors /1
(M7) and /2 (M8) turn ON to raise the lift plate. When the lift plate goes up and the upper most paper that is
loaded turns ON the upper limit sensors /1 (PS6) and /2 (PS13), M7 and M8 turn OFF to stop the up drive oper-
ation.
When the paper feed operation causes PS6 and PS13 to turn OFF from ON while in the print operation, M7 and
M8 turn ON again to raise the lift plate. In this way, when PS6 and PS13 turn ON again, M7 and M8 turn OFF to
stop the up drive operation.
42
Theory of Operation Ver.2.0 Jan. 2007 14. PAPER FEED SECTION (Tray 1/2)
bizhub 500/420/360
A. Paper size detection mechanism
(1) Size detection in the main scan direction
The side guide plate [12] is provided with the size detection actuator [7]. And interlocked with the side guide
plate, this actuator sticks out to the rear side of the tray. The size detection actuator is provided with the 2 lines
of notches, which are detected by the paper size sensors /Fr1 (PS11) [11] and /Rr1 (PS10) [10], or the paper
size sensors /Fr2 (PS17) [3] and /Rr2 (PS16) [4] equipped individually on the rear of the main body. The notches
of the size detection actuator vary for each paper size and the paper size is detected in the main scan direction
by the combination of the ON/OFF of PS10 and PS11, or PS16 and 17.
43
14. PAPER FEED SECTION (Tray 1/2) Theory of Operation Ver.2.0 Jan. 2007
Paper size Paper size boards /1 (PSB/1), /2 (PSB/2) Paper size sensor Paper size sensor
SW101 SW102 SW103 SW104 /Rr1 (PS10), /Rr2 /Fr1 (PS11), /Fr2
(PS16) (PS17)
B5 ON ON OFF OFF ON OFF
A5S ON/OFF OFF OFF OFF OFF OFF
A4 ON/OFF OFF OFF OFF ON OFF
81/2 x 11 OFF OFF OFF OFF OFF OFF
81/2 x 11S ON OFF OFF ON OFF ON
B5S OFF OFF ON OFF OFF OFF
A4S OFF ON/OFF ON ON OFF ON
81/2 x 14 ON ON ON OFF ON ON
B4 ON ON ON OFF ON OFF
A3 ON ON/OFF ON ON ON OFF
44
Theory of Operation Ver.2.0 Jan. 2007 14. PAPER FEED SECTION (Tray 1/2)
bizhub 500/420/360
A. Pick-up mechanism
The pick-up roller [4] is brought up and down mechanically by the lever [6] provided on the rear side of the paper
feed unit. When the tray is set, the lever is pushed by the tray to bring down the pick-up roller. In this way, the
pick-up roller comes in contact with paper to pick it up.
[6]
[1]
[5] [3]
[4] [2]
50gat2c098na
45
14. PAPER FEED SECTION (Tray 1/2) Theory of Operation Ver.2.0 Jan. 2007
B. Pick-up control
bizhub 500/420/360
46
Theory of Operation Ver.2.0 Jan. 2007 14. PAPER FEED SECTION (Tray 1/2)
C. Separation mechanism
bizhub 500/420/360
The separation roller [5] is pressed against the feed roller [8] by the operating pressure generated by the pres-
sure [2] of the spring [4] and the torque of the torque limiter [3]. This operating pressure of the feed roller, sepa-
ration roller and torque limiter becomes a limit torque to prevent the double feed of paper.
When there is no paper between the separation roller and the feed roller, or when only one sheet of paper is con-
veyed, the operating pressure of the feed roller, the paper and the spring is in excess of the limit torque, and
therefore, the separation roller rotates [6] following the rotation of the feed roller. When two or more sheets of
paper are conveyed between the separation roller and the feed roller, the limit torque is greater than the frictional
force between 2 sheets of paper, and accordingly, the separation roller stops and the lower side paper [7] in
contact with the separation roller is not conveyed.
[8] [1]
[2]
[3]
47
14. PAPER FEED SECTION (Tray 1/2) Theory of Operation Ver.2.0 Jan. 2007
The paper empty of the tray is detected by the paper empty sensors /1 (PS5) [3] and /2 (PS12) [4]. And to
prompt the supply of paper before paper in the tray runs out completely, the paper near-empty sensors /1 (PS9)
[7] and /2 (PS15) [8] are equipped. The lift drive shaft [2] that brings up the lift plate [5] is provided with the actu-
ator [1] and PS9 and PS15 are turned ON and OFF by this actuator. When a sufficient amount of paper is loaded
on the tray, the actuator turns ON PS9 and PS15. However, when the amount of paper gets reduced and the lift
plate goes up, the actuator turns OFF PS9 and PS15. In this way, it is detected that the paper loaded in the tray
comes near to an end.
[7] [8]
[1]
[2]
[3][4]
[6] [5]
50gat2c050na
48
Theory of Operation Ver.2.0 Jan. 2007 14. PAPER FEED SECTION (Tray 1/2)
bizhub 500/420/360
The front cover [4] of the tray is provided with the paper remaining display window [3], and the paper remaining
in the tray can be checked through this window. The inside of the paper remaining display window is provided
with the display lever [2] which is interlocked with the up/down position of the lift plate [1]. The display lever is red
in color and it is indicated that the more the red portion that can be seen through the paper remaining display
window, the less paper there remains in the tray.
[4] [1]
[3]
[2] 50gat2c053na
49
15. BYPASS SECTION Theory of Operation Ver.2.0 Jan. 2007
15.1 Composition
Feed roller
50gat2c019na
50
Theory of Operation Ver.2.0 Jan. 2007 15. BYPASS SECTION
15.2 Drive
bizhub 500/420/360
15.2.1 Paper feed drive
[4]
[1] [2]
[3]
50gat2c018na
[3] [2]
50gat2c020na
51
15. BYPASS SECTION Theory of Operation Ver.2.0 Jan. 2007
15.3 Operation
bizhub 500/420/360
[2] [1]
[6]
52
Theory of Operation Ver.2.0 Jan. 2007 15. BYPASS SECTION
bizhub 500/420/360
A. Size detection in the main scan direction
According to the position of the guide plate connected to the paper size VR/BP (VR1), the paper size is
detected in the main scan direction.
53
15. BYPASS SECTION Theory of Operation Ver.2.0 Jan. 2007
A. Pick-up control
When the feed motor (M9) is turned ON by the print start signal [1], the pick-up solenoid /BP (SD1) and the ver-
tical conveyance clutch (CL3) also turn ON a specified period of time after that. When SD1 turns ON, the lift
plate goes up [2] and paper comes into contact with the feed roller. After that, the feed clutch /BP (CL6) turns
ON. Through these operations, the driving force of M9 is transmitted to the feed roller and the vertical convey-
ance roller to conduct the pick-up [3] and the vertical conveyance [4] of the 1st sheet of paper. When paper is
conveyed and the vertical conveyance sensor (PS2) turns ON, CL6 turns OFF to complete the pick-up opera-
tion. However, since CL3 keeps turning ON, paper is conveyed to the registration section by the vertical convey-
ance roller. In this way, when the registration sensor (PS1) turns ON, CL3 turns OFF a specified period of time
after that. The pick-up [6] and the vertical conveyance [8] of the 2nd and succeeding sheets of paper are con-
ducted using the paper feed request signal [5] as a starting point. When the last paper turns ON PS2, SD1 turns
ON to bring down [7] the lift plate.
54
Theory of Operation Ver.2.0 Jan. 2007 15. BYPASS SECTION
B. Separation mechanism
bizhub 500/420/360
The separation roller [7] is pressed against the feed roller [1] by the operating pressure generated by the pres-
sure [4] of the spring [5] and the torque of the torque limiter [6]. This operating pressure of the feed roller, sepa-
ration roller and torque limiter becomes a limit torque to prevent the double feed of paper.
When there is no paper between the separation roller and the feed roller, or when only one sheet of paper is con-
veyed, the operating pressure of the feed roller, the paper and the spring is in excess of the limit torque, and
therefore, the separation roller rotates [3] following the rotation of the feed roller.
When two or more sheets of paper are conveyed between the separation roller and the feed roller, the limit
torque is greater than the frictional force between 2 sheets of paper, and accordingly, the separation roller stops
and the lower side paper [2] in contact with the separation roller is not conveyed.
[8] [1]
[7]
[6]
55
16. REGISTRATION SECTION Theory of Operation Ver.2.0 Jan. 2007
16.1 Composition
Registration roller
Loop roller
50gat2c021na
56
Theory of Operation Ver.2.0 Jan. 2007 16. REGISTRATION SECTION
16.2 Drive
bizhub 500/420/360
[1]
[6]
[2]
[3]
[5]
[4]
50gat2c022na
57
16. REGISTRATION SECTION Theory of Operation Ver.2.0 Jan. 2007
16.3 Operation
bizhub 500/420/360
[1]
[13]
[2]
[12]
[3]
[11]
[4]
[10]
[5]
[9]
[6]
[8] [7]
50gat2c055na
58
Theory of Operation Ver.2.0 Jan. 2007 16. REGISTRATION SECTION
B. Registration operation
bizhub 500/420/360
The feed motor (M9) and the loop clutch (CL2) are turned ON by the print start signal [1]. In this way, the driving
force of M9 is transmitted to the loop roller and paper conveyed from each of the paper feed sections is con-
veyed to the registration roller. When the registration sensor (PS1) detects the leading edge of paper and turns
ON [3], CL2 turns OFF a specified period of time after that. At this time, since paper is being conveyed for a
specified period of time after being hit against the registration roller, a loop [4] is formed and a paper skew is cor-
rected.
The print signal [5] turns ON the registration clutch (CL1) to transmit the driving force of M9 to the registration
roller. At this time, CL2 also turns ON to drive the loop roller for a loop assist [7].
When PS1 detects the trailing edge of paper and turns OFF [8], CL1 also turns OFF a specified period of time
after that to complete the registration operation. However, CL2 keeps tuning ON to conduct a loop formation [9]
of the next paper. After that, the same operations are repeated.
When PS1 detects the trailing edge of the last paper and turns OFF [11], M9, CL1 and CL2 also turn OFF a
specified period of time after that to complete a series of registration operations.
[1] Print start signal [8] Detection of the trailing edge of the 1st
[2] Conveyance of the 1st paper paper
[3] Detection of the leading edge of 1st paper [9] Loop formation of the 2nd paper
[4] Loop formation of the 1st paper [10] Print signal for the 2nd paper
[5] Print signal for the 1st paper [11] Detection of the trailing edge of the last
[6] 1st paper registration roller ON paper
[7] Loop assist of the 1st paper, and convey-
ance of 2nd of paper
59
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
17.1 Composition
Conveyance roller /1
Conveyance roller /2
50gat2c023na
60
Theory of Operation Ver.2.0 Jan. 2007 17. ADU SECTION
17.2 Drive
bizhub 500/420/360
[1] [2]
[3] [4]
[6]
[5] 50gat2c024na
61
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
17.3 Operation
bizhub 500/420/360
[12]
[1]
[11]
[10] [2]
[9]
[3]
[8]
[7]
[4]
[6]
[5]
50gat2c057na
62
Theory of Operation Ver.2.0 Jan. 2007 17. ADU SECTION
bizhub 500/420/360
When printing two or more sheets of paper in the double sided print mode, the conveyance control in ADU var-
ies according to the length of paper in the sub scan direction. The following 3 control methods are provided for
the conveyance control.
Note
• A figure in the illustration (shown in the square) represents the page number.
50gat2c058na
50gat2c059na
63
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
out interruption.
50gat2c060na
1
2
50gat2c061na
50gat2c062na
64
Theory of Operation Ver.2.0 Jan. 2007 17. ADU SECTION
bizhub 500/420/360
Note
• A figure in the illustration (shown in the square) represents the page number.
50gat2c063na
50gat2c064na
50gat2c065na
65
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
50gat2c066na
50gat2c067na
50gat2c068na
50gat2c069na
66
Theory of Operation Ver.2.0 Jan. 2007 17. ADU SECTION
bizhub 500/420/360
image of the 8th page (the back side of the 4th
sheet of paper when the original is double sided)
is printed on the 4th sheet of paper. At this time,
4
the 3rd sheet of paper is standing by on this side
3 8
of the conveyance roller /3.
2
1
6
50gat2c070na
50gat2c071na
67
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
Note
• A figure in the illustration (shown in the square) represents the page number.
50gat2c072na
50gat2c073na
50gat2c074na
68
Theory of Operation Ver.2.0 Jan. 2007 17. ADU SECTION
bizhub 500/420/360
reverse/exit section and the 2nd sheet of paper is
6 4 conveyed in ADU without interruption. However,
the 1st sheet of paper remains standing by at the
conveyance roller /3.
50gat2c075na
50gat2c076na
50gat2c077na
50gat2c078na
69
17. ADU SECTION Theory of Operation Ver.2.0 Jan. 2007
50gat2c079na
70
Theory of Operation Ver.2.0 Jan. 2007 18. FUSING SECTION
bizhub 500/420/360
18.1 Composition
Fusing heater
Fusing web lamp /1 (L2) Fusing roller Paper exit roller Decurler roller
18.2 Drive
[1]
[2]
50gat2c026na
71
18. FUSING SECTION Theory of Operation Ver.2.0 Jan. 2007
18.3 Operation
bizhub 500/420/360
72 1
Theory of Operation Ver.2.0 Jan. 2007 18. FUSING SECTION
bizhub 500/420/360
The fusing roller is heated by the fusing heater lamps /1 (L2) and /2 (L3). The fusing pressure roller is heated by
the thermal conduction from the fusing roller.
The surface temperature of the fusing roller is detected by the thermistors /1 (TH1) [2] and /2 (TH2) [1]. TH1 and
TH2 monitor the surface temperature of the fusing roller at specified intervals to control the ON/OFF of L2 and
L3 through the AC drive circuit in the DC power supply (DCPS) so that a prescribed temperature can be
obtained.
[1] [2]
50gat2c081na
A. Warm-up
Warm-up is conducted when the main power switch (SW1), the power switch (SW2) and the interlock switch
(MS) turn ON, and also when the system returns from the low power mode or the sleep mode.
While in the warm-up, the fusing heater lamps /1 (L2) and /2 (L3) turn ON. And it turns OFF at the prescribed
temperature. The temperature at which the warm-up completes varies for bizhub 500 and 420/360.
1 73
18. FUSING SECTION Theory of Operation Ver.2.0 Jan. 2007
When each key is not pressed within a specified period of time after the completion of the last print, the system
changes into the low power mode or the sleep mode. The starting time for operation can be set individually for
the low power mode and the sleep mode. When the same starting time for operation is set for both modes, the
sleep mode takes precedence over the low power mode.
When the system changes into the low power mode, the ON/OFF of the fusing heater lamps /1 (L2) and /2 (L3)
is controlled so that the fusing roller gets to the prescribed temperature. The controlled temperature at this time
becomes lower than other controlled temperatures. And when the system changes into the sleep mode, the
power supply to L2 and L3 is shut off to put the system in the stand-by condition.
Note
• When the power switch (SW2) turns OFF due to the occurrence of a jam, or when the interlock
switch (MS) is turned OFF by opening ADU, the power supply to each fan is shut off and, even if it
is within a specified period of time, the fan turns OFF. However, when SW2 and MS are turned ON
within a specified period of time, FM2 and FM8 turn ON again.
74
Theory of Operation Ver.2.0 Jan. 2007 18. FUSING SECTION
bizhub 500/420/360
The air inside the machine is sucked in by the fusing cooling fans /Fr (FM2) [6] and /Rr (FM8) [1] to be blown
against the edges of the fusing roller [3] through the ducts [2] and [5]. In this way, the edges of the fusing roller
are cooled down and the surface temperature of the edges of the fusing pressure roller [4] that is in contact also
goes down.
[1]
[2]
[6]
[3]
[4]
[5]
50gat2c082na
[1] Fusing cooling fan /Rr (FM8) [4] Fusing pressure roller
[2] Duct [5] Duct
[3] Fusing roller [6] Fusing cooling fan /Fr (FM2)
[1]
50gat2c083na
75
18. FUSING SECTION Theory of Operation Ver.2.0 Jan. 2007
When the thermistors /1 (TH1) and /2 (TH2) detects a stipulated temperature (233°C) 5 times at the prescribed
intervals, this is deemed to be a high temperature abnormality and the fusing heater lamps /1 (L2) and /2 (L3) are
turned OFF. The thermostat (TS) also monitors an abnormal temperature rise and, when the detected tempera-
ture gets to 220 ± 10°C, the AC power lines to L2 and L3 are shut off.
For each condition in the warm-up, print, stand-by and the low power modes, the detected temperatures of
TH1 and TH2 and the number of times when L2 and L3 turned ON are calculated. And it is considered that a
low temperature abnormality occurs when certain conditions are met. When a low temperature abnormality
occurs, the power supply to L2 and L3 is cut off.
When these fusing temperature abnormalities occur, the system is placed in the SC latch condition with a mes-
sage shown in the touch panel. After repairing with the cause of abnormality identified, it is necessary to release
the SC latch by the software DipSW3-1 for restoration.
RL1 DCPS
TS
CBR NF
RL2
AC L2
drive
section L3
PRCB
TH1
Control
section
RL RL1
drive
section RL2
TH2
50gat2c084na
76
Theory of Operation Ver.2.0 Jan. 2007 19. REVERSE/EXIT SECTION
bizhub 500/420/360
19.1 Composition
19.2 Drive
[4] [1]
[3] [2]
50gat2c028na
77
19. REVERSE/EXIT SECTION Theory of Operation Ver.2.0 Jan. 2007
19.3 Operation
bizhub 500/420/360
B. Conveyance path
(1) Paper exit path
The reverse solenoid (SD3) is normally turned OFF and the reverse gate [1] is held in the position in which it
blocks the conveyance path to the reverse roller [4]. In this manner, paper conveyed from the fusing exit roller
(decurler roller) [2] is guided to the main body paper exit roller [3] along the internal form of the reverse gate to be
exited.
[4]
[1]
[3]
[2]
50gat2c085na
78
Theory of Operation Ver.2.0 Jan. 2007 19. REVERSE/EXIT SECTION
bizhub 500/420/360
While in the double sided print, the reverse solenoid (SD3) turns ON when the print on the back side is com-
pleted, and the reverse gate [1] is switched in the direction in which the conveyance path to the reverse roller [4]
is opened. In this way, paper conveyed from the fusing exit roller (decurler roller) [2] is guided to the reverse roller
along the external form of the reverse gate.
[4]
[1]
[3]
[2]
50gat2c086na
79
19. REVERSE/EXIT SECTION Theory of Operation Ver.2.0 Jan. 2007
A. Switch-back mechanism
While in the double sided print, paper that passes through the reverse gate [3] is conveyed to the outside of the
main body by the reverse roller [5] and then sent back again to the inside of the main body. At this time, the
paper is guided to the conveyance roller /1 [1] side, not to the reverse gate side from the metal frame form of the
conveyance path. In this way, the paper is turned over to be conveyed to the registration section again through
ADU.
The ON/OFF timing of the reverse solenoid (SD3) that drives the reverse gate is controlled by the fusing exit sen-
sor (PS3) [2]. And the switchover between the normal rotation and the reverse rotation of the reverse motor (M6)
that drives the reverse roller is controlled by the reverse sensor (PS27) [4].
[5]
[4]
[1]
[3]
[2]
50gat2c087na
80
Theory of Operation Ver.2.0 Jan. 2007 19. REVERSE/EXIT SECTION
B. Reverse control
bizhub 500/420/360
While in the double sided print, when the fusing exit sensor (PS3) detects the leading edge of paper of which the
printing of the back side has been completed and turns ON [1], the reverse solenoid (SD3) turns ON to switch
the reverse gate a specified period of time after the registration clutch (CL1) turns ON for back side printing. In
this manner, the paper is conveyed to the reverse section. A specified period of time after the reverse sensor
(PS27) detects the leading edge of paper and turns ON [2], the reverse motor (M6) rotates in the normal direc-
tion [3] and the reverse roller conveys the paper to the outside of the main body. And then, a specified period of
time after PS3 detects the trailing edge of the paper and turns OFF [4], SD3 turns OFF [5] to bring the reverse
gate back to its original position. And when PS27 detects the trailing edge of the paper and turns OFF [6], the
rotation of M6 is switched [7] from the normal rotation to the reverse rotation and the reverse roller sends the
paper back to the inside of the main body to convey it to ADU. In this manner, the paper is turned over.
Normal
Reverse motor (M6) rotation
Reverse
rotation
Reverse solenoid (SD3)
[1] Switchover of the reverse gate [5] Return to the reverse gate
[2] Detection of the leading edge of paper [6] Detection of the trailing edge of paper
[3] Normal rotation of the reverse roller ON [7] Switchover of the reverse roller from the nor-
[4] Detection of the trailing edge of paper mal rotation to the reverse rotation
81
20. INTERFACE SECTION Theory of Operation Ver.2.0 Jan. 2007
20.1 Composition
50gat2c089na
20.2 Specifications
Item Specifications
Serial port (RS-232C) For CS Remote Care
Parallel port (based on IEEE1284) For ISW of the copier/printer
USB port (USB TypeB) For ISW of the copier/printer
RJ45 Ethernet connector (Spare)
82
Theory of Operation Ver.2.0 Jan. 2007 21. IMAGE STABILIZATION CONTROL
bizhub 500/420/360
21.1 Outline
This machine employs various image stabilization controls to realize the top quality print image at all times. The
operation of the image stabilization control varies between while in the power switch (SW2) ON and while in the
print.
B. Drum rotation
D. Fusing preliminary rotation
C. Dot diameter adjustment control
Stand-by
83
21. IMAGE STABILIZATION CONTROL Theory of Operation Ver.2.0 Jan. 2007
B. Drum rotation
bizhub 500/420/360
(1) Purpose
• Prevent the drum charge leak such as an image flow at high humidity
• When left in the low/normal humidity condition, prevent the uneven density due to the difference in sensitiv-
ity between the section facing the cleaner and the developing of the drum and other sections.
Note
• For bizhub 420/360, since the early morning dot diameter adjustment is not selected by default, no
drum rotation is made.
(2) Method
• Create a dot pattern patch of a fixed density on the drum. The laser PWM at this time is maximum.
• Read this dot pattern patch with the IDC sensor (IDCS) and calculate the difference between the sensor
output and the specified value.
• Determine the correction amount of the laser power based on a value calculated to make corrections of the
laser power.
• Repeat several times the control operations described above.
Note
• For bizhub 420/360, since the early morning dot diameter adjustment is not selected by default, no
execution is made.
Note
• The stipulated temperature at which the fusing preliminary rotation is made varies for bizhub 500
and 420/360.
84 1
Theory of Operation Ver.2.0 Jan. 2007 21. IMAGE STABILIZATION CONTROL
bizhub 500/420/360
(1) Purpose
To detect the environmental temperature and humidity to maintain the image quality, feedback is made to vari-
ous controls.
(2) Method
A temperature sensor and a humidity sensor are equipped inside the machine.
85
21. IMAGE STABILIZATION CONTROL Theory of Operation Ver.2.0 Jan. 2007
21.2.2 Image stabilization control flow while in the print and the idle
bizhub 500/420/360
The following shows the image stabilization control flow while in the print and the idle.
Every 20 prints
Start of print
End of print
Stand-by
(2) Method
Detect the machine inside humidity with the humidity sensor (HUMS) when turning ON the power switch (SW2)
8 hours or more after turning it OFF.
Calculate the correction amount based on the machine inside humidity detected and the time period during
which the photosensitive material is driven.
Make corrections of the output value of the charging grid and the developing bias based on the correction
amount calculated.
When the time period during which SW2 is turned ON after OFF is less than 8 hours, use the value of the
machine inside humidity detected last time.
86 1
Theory of Operation Ver.2.0 Jan. 2007 21. IMAGE STABILIZATION CONTROL
bizhub 500/420/360
(2) Method
• Create a dot pattern patch between images of which more than 20 prints have been run off. The laser PWM
at this time is maximum.
• Read this dot pattern patch with the IDC sensor (IDCS) and calculate the difference between the sensor
output and the specified value.
• Determine the correction amount of the laser power based on a value calculated to make corrections of the
laser power.
• Repeat several times the control operations described above.
87
22. IMAGE PROCESSING Theory of Operation Ver.2.0 Jan. 2007
A. Shading correction
B. AE control
C. Area discrimination
D. Brightness/density conversion
E. Filter/magnification
H. Compression
88
Theory of Operation Ver.2.0 Jan. 2007 22. IMAGE PROCESSING
bizhub 500/420/360
This is the measure to obtain an even distribution from light of the CCD sensor. The following corrections are
made at the prescribed timing.
a. White correction
The output voltage of each pixel of the CCD sensor when the white reference plate is exposed to the exposure
lamp is stored as the maximum output of the pixel.
b. Black correction
The output voltage of each pixel of the CCD sensor when the exposure lamp is turned off is stored as the mini-
mum output of the pixel.
Conduct calculation to find out what step in this range falls on the image data read from the original based on
the difference between the black and white data for each pixel stored in the steps a. and b. above, and output
the results of the calculation in the 10 bits accuracy.
0V
Black
Width in which the read is made
0
Width in which the read is made Black
50gat2c091na
89
22. IMAGE PROCESSING Theory of Operation Ver.2.0 Jan. 2007
22.1.2 AE control
bizhub 500/420/360
Through the AE control, a density suitable for the original density is automatically selected and the copy is made
properly.
A. Sampling area
(1) While in the platen mode
[5]
[1]
[7]
[6]
[5]
[2] [2]
[4]
[3]
50gat2c092na
[4]
[1]
[6]
[5]
[4]
[3] [2]
50gat2c093na
B. Execution timing
• While in the platen print: At the pre-scan before the actual scan when the print or the read starts.
• While in the DF print : At the same time as when the original is read.
90
Theory of Operation Ver.2.0 Jan. 2007 22. IMAGE PROCESSING
bizhub 500/420/360
To make a copy of the original under the correct condition (to make a correct filter processing), check the read
section to see if it is a character or a dot picture, and use the results at the image processing unit at the later
stage.
255
Density
91
22. IMAGE PROCESSING Theory of Operation Ver.2.0 Jan. 2007
22.1.5 Filter/magnification
bizhub 500/420/360
A. Filter processing
An appropriate filter processing is made according to the type of an original and the magnification selected.
B. Magnification processing
For this machine, the sub scan direction magnification is made by the scan speed of the exposure unit (platen
mode) or by the conveyance speed of the DF (DF mode), and the main scan direction magnification is made by
processing images electrically.
a. There occurs a clearance between data, and this results in a distorted image.
b. The data position does not fall in exactly with the write position.
As shown with dotted lines in the drawing below, when there is no read data that corresponds exactly to the
write position, a density is decided for the write as shown below and appropriate processing is made.
[1] D1 D2 D3 D4 D5
[2] E1 E2 E3 E4 E5
[3] W1 W2 W3 W4 W5 W6 W7 W8
50gat2c095na
92
Theory of Operation Ver.2.0 Jan. 2007 22. IMAGE PROCESSING
bizhub 500/420/360
As shown in drawing below, if the data of each pixel obtained when the original is read by the CCD are D1 to D5,
the positions of the data read when reduced are R1 to R5. They are overlapping each other and do not corre-
spond to the write position. Therefore, a density is decided for the write as shown below and an appropriate
processing is made.
[1] D1 D2 D3 D4 D5
[2] R1 R2 R3 R4 R5
[3] W1 W2 W3 W4 W5
50gat2c096na
255
E2
W2
S
Density
E1
0
0 Position 15 50gat2c097na
93
22. IMAGE PROCESSING Theory of Operation Ver.2.0 Jan. 2007
To the data obtained after the filter/magnification processing, select a density curve corresponding to the density
button selected on the operation panel. An appropriate density curve is provided for each of the character/pic-
ture/character and the picture/thin character modes.
22.1.8 Compression
To store more image data, data is stored temporarily in the image memory after the images has been com-
pressed.
94
Theory of Operation Ver.2.0 Jan. 2007 22. IMAGE PROCESSING
bizhub 500/420/360
A. Rotation/elongation
B. PWM
C. Frequency conversion
A. Rotation/elongation
Rotate the image in the direction of 90 degrees and 180 degrees as necessary.
When outputting images from the memory, expand the compressed data to restore them to their original state.
B. PWM
The period of time the laser is turned ON is changed by changing the pulse width.
C. Frequency conversion
Write in the memory once the data after the PWM conversion and read it in accord with the write clock signal of
the printer.
95
23. OTHERS Theory of Operation Ver.2.0 Jan. 2007
23. OTHERS
bizhub 500/420/360
[7]
[6]
[1]
[5]
[2]
[4]
[3]
50gat2c029na
[1] Exhaust fan /Rr (FM9) [6] Fusing cooling fan /Fr (FM2)
[2] Exhaust fan /Fr (FM3) [7] Fusing cooling fan /Rr (FM8)
[3] Conveyance suction fan (FM5) [8] Power supply cooling fan (FM1)
[4] Drum cooling fan (FM4) [9] Overall control board cooling fan (FM10)
[5] Developing suction fan (FM6) [10] Developing cooling fan (FM7)
96
Theory of Operation Ver.2.0 Jan. 2007 23. OTHERS
23.1.2 Operation
bizhub 500/420/360
A. Power supply cooling fan (FM1) control
(1) Purpose
Cool down the DC power supply (DCPS) and the high voltage unit (HV2) with suction air.
(2) ON timing
• It turns ON a specified period of time after the drum motor (M1) turns ON.
• While in the auto toner supply mode and the TCR adjustment mode, it turns ON in synch with the turn-ON
of M1.
• While in the low power mode and the stand-by condition, it turns ON in synch with the turn-ON of the drum
cooling fan (FM4).
(2) ON timing
• While in the print of small size paper, they turn ON when the fusing exit sensor detects the first job paper .
• While in the print of large size paper, they turn ON when the thermistor /2 (TH2) goes over the prescribed
temperature.
• They turn ON when the print operation is stopped by a jam.
(2) ON timing
• They turn ON in synch with the turn-ON of the drum motor (M1).
97
23. OTHERS Theory of Operation Ver.2.0 Jan. 2007
(1) Purpose
Cool around the drum and the toner bottle with suction air.
(2) ON timing
• After completion of the print, it turns ON a specified period of time after the drum motor (M1) turns OFF.
• It turns ON when the machine inside temperature goes over the prescribed temperature.
(2) ON timing
• It turns ON in synch with the turn-ON of the drum motor (M1).
• While in the low power mode and the stand-by condition, it turns ON in synch with the turn-ON of the drum
cooling fan (FM4).
(2) ON timing
• It turns ON in synch with the turn-ON of the developing motor (M3).
98
Theory of Operation Ver.2.0 Jan. 2007 23. OTHERS
bizhub 500/420/360
(1) Purpose
Take in fresh air to cool down the developing motor (M3).
(2) ON timing
• After completion of the print, it turns ON a specified period of time after M3 turns OFF.
• While in the auto toner supply mode, it turns ON in synch with the turn-ON of M3.
• It turns ON when the machine inside temperature goes over the prescribed temperature.
(2) ON timing
• It turns ON when the power switch (SW2) turns ON.
99
23. OTHERS Theory of Operation Ver.2.0 Jan. 2007
23.2.1 Composition
[2] [1]
OB CN936
SDB CN64
3 6 KCT
LCDB
50gat2c030na
100 1
Theory of Operation Ver.2.0 Jan. 2007 23. OTHERS
23.2.2 Operation
bizhub 500/420/360
A. Paper exit counter
Item Specifications/mechanism
Total counter (TCT) • Display accumulated number of prints in all print modes.
• Counts up by a paper exit signal.
Electronic counter • Display accumulated number of prints on the touch
panel.
• Data collection *1
• Counts up by a paper exit signal.
Key counter (KCT), optional • Counting the designated number of prints allows no fur-
ther copy operation (can be removed).
*1 For data collected, See "10.6 Counter" in Field service bizhub 500/420/360 Main body. (See P.201)
[2] [1]
50gat2c031na
101
23. OTHERS Theory of Operation Ver.2.0 Jan. 2007
Connector Pin No. Signal name Description Output timing Type of signal
36 1 M1 signal Output from the start L output while in the Open collec-
key being turned ON print operation tor output
up to the completion of
paper exit
2 Paper feed signal Output each time L output each time
paper is supplied paper is supplied from
each tray
3 Paper size signal (0) Signal output by paper When the paper size is
4 Paper size signal (1) sizes *1 changed
5 Paper size signal (2)
6 Paper size signal (3)
7 Double sided print Signal output while in While in the selection
selection signal the double sided print of the double sided
print
8 CPF signal (0) Signal output by CPF While in the selection
9 CPF signal (1) modes of the CPF mode
10 P.GND Ground — —
102
Theory of Operation Ver.2.0 Jan. 2007 23. OTHERS
bizhub 500/420/360
23.3.1 Parts that operate when the main power switch (SW1) is turned ON
A. Composition
SW2
SW1 PSWB
OB
DCPS
5VDC
IC
12VDC
DCPS
CBR NF OACB FK
section
HD
24VDC SC
PC LU PRCB
50gat2c032na
B. Operation
Turning ON the main power switch (SW1) supplies an AC power source to DC power supply (DCPS).
In this way, each power source of 12V DC and 5V DC is supplied to the overall control board (OACB).
OACB supplies 5V DC to the operation board (OB) to be placed in the condition of standing by for the turn-ON
of the power switch (SW2).
When equipped optionally with the FAX kit (FK-502) and the hard disk (HD-505), each power source of 12V DC
and 5V DC is supplied through OACB.
103
23. OTHERS Theory of Operation Ver.2.0 Jan. 2007
23.3.2 Parts that operate when the power switch (SW2) is turned ON
bizhub 500/420/360
A. Composition
SW2
PSWB
OB
SW1
OACB
24VDC
DCPS
RL1
CBR NF
section
RL2
L2, L3
AC drive
section
DCPS
50gat2c033na
B. Operation
Turning ON the power switch (SW2) transmits an ON signal of SW2 to the overall control board (OACB) through
the operation board (OB). In this way, OACB sends out a control signal to the DC power supply (DCPS) and
DCPS supplies each power source of 12V DC and 5V DC to all boards and optional devices, including the
printer control board (PRCB).
After that, OACB sends out to DCPS a control signal that generates a 24V DC power source, which is supplied
to all drive boards and optional devices. And when the main relay (RL1) and the sub relay (RL2) turn ON, an AC
power source is supplied to the fusing heater lamps /1 (L2) and /2 (L3) to start the initial operation of this
machine.
104
SERVICE MANUAL Theory of Operation
DF-607
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
DF-607
DF-607
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
2. PAPER PATH..........................................................................................................4
2.1 In 1-sided mode ....................................................................................................4
2.2 In 2-sided mode ....................................................................................................4
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................5
4. DRIVE......................................................................................................................6
5. OPERATION ...........................................................................................................7
5.1 Document pick-up mechanism..............................................................................7
5.1.1 Pick-up operation ..........................................................................................7
5.2 Document feed/conveyance mechanism ..............................................................8
5.3 Raised/lowered position detecting mechanism...................................................12
5.3.1 DF 15° open/close detection mechanism....................................................12
5.3.2 DF open/close detection mechanism ..........................................................12
i
CONTENTS Theory of Operation Ver.1.0 Feb. 2006
DF-607
Blank Page
ii
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
DF-607
A. Type
B. Functions
C. Paper type
1-Sided Mode
Standard Mode 35 to 128 g/m2 (9.25 to 34 lbs)
Plain Paper 2-Sided Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Mixed Original Detection
1-Sided / 2-Sided Mode
Type of Document Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Plain Paper
1-Sided Mode
FAX Mode 35 to 128 g/m2 (9.25 to 34 lbs)
Plain Paper 2-Sided Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Inch area
A3, A4S, A4, B4, B5S, B5
Detectable Document 11 x 17, 81/2 x 14, 81/2 x 11S, 81/2 x 11, 81/2 x 51/2S, 81/2 x 51/2
Size*1 Metric area
A3, A4S, A4, A5S, A5, B4, B5S, B5, B6S
11 x 17, 81/2 x 11S, 81/2 x 11
Capacity 80 sheets (80 g/m2) or load height of 11 mm or less.
*1: For the Combined Original Detection Mode, Refer to the Mixed Original Detection Enabled
Size Combination Table.
1
1. PRODUCT SPECIFICATIONS Theory of Operation Ver.1.0 Feb. 2006
2
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
DF-607
Reference original (original with a maximum width)
A3 A4 B4S B5 A4S A5 B5S A5
Other A3 U { — — — — — —
originals A4 { U — — — — — —
B4S ~ ~ U { — — — —
B5 ~ ~ { U — — — —
A4S ~ ~ ~ ~ U { — —
A5 ~ ~ ~ ~ { U — —
B5S X X ~ ~ ~ ~ U —
A5S X X X X X X X U
U: Same size {: Same group ~: Different group X: Mix prohibited —: No need to set
For Inch
G. Maintenance
H. Machine data
I. Operating environment
Temperature 10 to 30°C
Humidity 10 to 80% RH (with no condensation)
NOTE
• These specifications are subject to change without notice.
3
2. PAPER PATH Theory of Operation Ver.1.0 Feb. 2006
2. PAPER PATH
2.1 In 1-sided mode
DF-607
4
Theory of Operation Ver.1.0 Feb. 2006 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
DF-607
Document feed section
5
4. DRIVE Theory of Operation Ver.1.0 Feb. 2006
4. DRIVE
DF-607
[1]
[2]
16eat2c002na
[1] Original Feed Motor (M1) [2] Original Conveyance Motor (M2)
6
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
5. OPERATION
5.1 Document pick-up mechanism
DF-607
• The Document Pick-Up Section consists of the Pick-Up Rollers, Feed Roller and Separation
Roller, and this section is driven by the Original Feed Motor (M1).
[3]
[4]
[2]
[1] 16eat2c003na
7
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
rotating forward and, at the same time that the Pickup Roller goes up, drive is then supplied
to the Registration Roller [3].
• When the Original Conveyance Motor (M2) [4] starts rotating forward, the two Conveyance
Rollers [2] and the Exit/Turnover Roller [1] feed the document toward the exit direction.
Direction of
Parts Details
Rotation
Backward The Pickup Rollers lower and start rotating and the Feed
rotation Roller rotates.
M1
Forward
The Registration Roller rotates.
rotation
Backward The Conveyance Roller and Exit/Turnover Roller rotate in
rotation the direction to turn over the original.
M2
Forward The Conveyance Roller and Exit/Turnover Roller rotate in
rotation the direction to feed the original out.
[5]
[1]
[4]
[3]
[2]
16eat2c004na
8
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
[4]
DF-607
[1]
1. When the Start key is pressed, the Original Feed Motor (M1) starts rotating backward,
causing the Pick-Up Roller to lower and start a paper take-up sequence.
2. A specified period of time after the leading edge of the original turns ON PS8 [4], the
scanning of the 1st side of the original starts.
3. The original is conveyed for a given period of time after the trailing edge of the last
page of the document has deactivated the PS10 [2]. It is then fed into [1] the Exit Tray
and the Original Conveyance Motor (M2) is deenergized.
9
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
A specified period of time after the leading edge of the original turns ON the Original
Detection Sensor (PS8) [4], the scanning of the 1st side of the original starts.
The Original Conveyance Motor (M2) is deenergized to stop [1] the original after the
lapse of a given period of time after the trailing edge of the 1st page has deactivated
the Original Exit Sensor (PS10) [2].
[4]
[1]
2. M2 is turned backward to turn over [3] the original. After the Registration Roller, M2 is
turned forward to allow the Scanner to scan the backside of the 1st page.
3. After the conveyance sequence for turnover has been started, the Pressure Roller
Release Solenoid (SD1) is energized so that the Exit/Turnover Roller is retracted.
[3]
[1]
[2] 16eat2c007na
10
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
4. To ensure that pages of the document are in the proper order, the page is turned over
[3] again before being ejected [1] into the Exit Tray.
DF-607
[3]
[1]
[2] 16eat2c008na
11
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
• When DF is closed down to about 15° or less, the Original Cover Angle Detection Lever of
the main body is pressed down to turn ON the APS Timing Sensor (PS31).
[1]
16eat2c009na
12
SERVICE MANUAL Theory of Operation
PC-202
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
PC-202
PC-202
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
2. PAPER PATH..........................................................................................................2
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................3
4. DRIVE......................................................................................................................4
5. OPERATIONS .........................................................................................................5
5.1 Paper Feed Section ..............................................................................................5
5.1.1 Paper feed mechanism .................................................................................5
5.1.2 Paper lifting motion........................................................................................6
5.2 Tray Section..........................................................................................................7
5.2.1 Paper size detection......................................................................................7
5.2.2 Paper level indicator mechanism ..................................................................8
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
PC-202
Blank Page
ii
Theory of Operation Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
PC-202
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
2. PAPER PATH
PC-202
[4]
[1]
[2]
[3]
4061t1c001na
2
Theory of Operation Ver.2.0 Jan. 2007 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
PC-202
Tray 3
Paper Feed
Section
Tray 4 4061t2c001na
3
4. DRIVE Theory of Operation Ver.2.0 Jan. 2007
4. DRIVE
PC-202
[4] [1]
[3]
[2]
4061t2c002na
[1] Vertical Conveyance Motor /3 (M120) [3] Vertical Conveyance Motor /4 (M121)
[2] Paper Feed Motor /4 (M123) [4] Paper Feed Motor /3 (M122)
4
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5. OPERATIONS
5.1 Paper Feed Section
PC-202
5.1.1 Paper feed mechanism
• The Paper Feed Motor (M122, M123) drives the Pick-up Roller [8] and Feed Roller [6] to
take up and feed a sheet of paper into the main body.
• Then, the Vertical Conveyance Motor /3, /4 (M120, M121) transports the paper through the
vertical conveyance section.
• The Pick-up Roller takes up sheet of paper and the Feed Roller and Separation Roller [5]
ensure that only one sheet of paper is separated and fed into the main body.
• When the Tray is slid in, the lever [7] is pushed to lower the Pick-up Roller.
• The Upper Limit Sensor /3, /4 (PS114, PS123) [9] then detects the upper limit position when
the paper lifting plate is raised.
• The Paper Empty Sensor /3, /4 (PS115, PS124) [1] detects when paper in the Tray runs out.
[4] [3]
4061t2c003na
[1] Paper Empty Sensor /3, /4 (PS115, PS124) [6] Feed Roller
[2] Actuator [7] Lever
[3] Pick-up Roller Feed Position [8] Pick-up Roller
[4] Pick-up Roller Home Position [9] Upper Limit Sensor /3, /4 (PS114, PS123)
[5] Separation Roller
5
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
[3].
• The paper stack of the Tray pushes up the Pick-up Roller [1]. When the upper limit position
is detected by the Upper Limit Sensor /3, /4 (PS114, PS123) [4], it stops raising the lifting
plate.
• As paper is consumed during the print cycle and the Pick-up Roller is lowered, M124, M125
is energized until PS114, PS123 is blocked again.
A. When the Tray is slid in
1. The lifting plate [3] goes up and the top surface of the paper stack pushes up the roller
[1].
2. The lifting motion stops as soon as the Upper Limit Sensor /3, /4 (PS114, PS123)
detects the upper limit position.
[4] [1]
[1]
4061t2c005na
6
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
PC-202
• Moving the Sub Scan Direction Restriction Plate of the Tray rotates the Circular Plate [1]
provided on the bottom of the Tray.
• The length of paper in the sub scan direction is detected by the Paper Size Detection Switch
[8] provided on the Paper Size Detect Boards /3 and /4 (PSDB3, PSDB49) [7] that is driven
by the Lever interlocked with the Circular Plate.
• The detection of the length of paper in the main scan direction is made by detecting a notch
on the Lever of the Main Scan Direction Restriction Plate by the Paper Size Sensors /Rr3,
/Fr3 (PS118, PS119) [2] or /Rr4, /Fr4 (PS127, PS128) [3].
• The paper size is determined by the combination of the 4 Paper Size Detection Switches
and the 2 Paper Size Sensors.
• The setting of the Tray is detected by the Tray Set Sensors /3, /4 (PS112, PS121) [6].
[9]
[1] Circular Plate [6] Tray Set Sensor /3, /4 (PS112, PS121)
[2] Paper Size Sensor /Rr3, /Rr4 (PS118, [7] Paper Size Detect Board /3, /4 (PSDB3,
PS127) PSDB4)
Paper Size Sensor /Fr3, /Fr4 (PS119,
[3] [8] Paper Size Detection Switch
PS128)
[4] Paper Lift Motor /3, /4 (M124, M125) [9] Sub scan direction size detection
[5] Main scan direction size detection
7
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
[5]
[4] [1]
[3] [2]
4061t2c007na
8
SERVICE MANUAL Theory of Operation
PC-402
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
PC-402
PC-402
OUTLINE
1. PRODUCT SPECIFICATION ..................................................................................1
2. PAPER PATH..........................................................................................................2
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................3
4. DRIVE......................................................................................................................4
5. OPERATIONS .........................................................................................................5
5.1 Paper Feed Section ..............................................................................................5
5.1.1 Paper feed mechanism .................................................................................5
5.2 Tray Section..........................................................................................................6
5.2.1 Up/down mechanism.....................................................................................6
5.2.2 Shift Gate drive mechanism ..........................................................................7
5.2.3 Shifter drive mechanism................................................................................8
5.2.4 Paper empty detection ..................................................................................9
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
PC-402
Blank Page
ii
Theory of Operation Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATION
OUTLINE
1. PRODUCT SPECIFICATION
PC-402
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
2. PAPER PATH
PC-402
[1]
[2]
[1] Convey to the main body [4] From the Sub Tray to Main Tray
[2] Tray paper feed [5] Sub Tray
[3] Main Tray
2
Theory of Operation Ver.2.0 Jan. 2007 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
PC-402
Tray Section Paper Feed Section
3
4. DRIVE Theory of Operation Ver.2.0 Jan. 2007
4. DRIVE
PC-402
[1]
[2]
[6]
[3]
[5] [4]
4061t2c202na
[1] Paper Lift Motor (M5) [6] Shift Gate Drive Section
[2] Paper Lift Drive Section [7] Tray Lock Solenoid (SD1)
[3] Shifter Drive Section [8] Paper Feed Motor (M1)
[4] Shift Motor (M4) [9] Vertical Conveyance Motor (M2)
[5] Shift Gate Motor (M3) [10] Vertical Conveyance Drive Section
4
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5. OPERATIONS
5.1 Paper Feed Section
PC-402
5.1.1 Paper feed mechanism
• The Paper Feed Motor (M1) drives the Pick-up Roller [8] and Feed Roller [6] to take up and
feed a sheet of paper into the main body.
• Then, the Vertical Conveyance Motor (M2) transports the paper through the vertical convey-
ance section.
• The Pick-up Roller takes up sheet of paper and the Feed and Separation Rollers [5] ensure
that only one sheet of paper is separated and fed into the main body.
• When the Tray is slid in, the lever [7] is pushed to lower the Pick-up Roller.
• The Upper Limit Sensor (PS4) [9] then detects the upper limit position when the paper lifting
plate is raised.
• The Paper Empty Sensor (PS3) [1] detects when paper in the Main Tray runs out.
[4] [3]
4061t2c203na
5
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
• The Main Tray [3] is suspended by the cables [1] at the front and rear.
• As the Paper Lift Motor (M5) [5] turns forward or backward, the cables are wound to raise or
lower the Main Tray.
• The Lower Limit Sensor (PS13) [2] detects the Main Tray at its lower limit position.
[1]
[5] [2]
[3]
[4]
4061t2c204na
6
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
PC-402
• At this time, the Shift Gate Motor (M3) [4] is energized to retract the front and rear Shift
Gates [1].
[1]
[4]
[3]
[2]
[1] 4061t2c205na
7
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
[3]
[2]
[2]
[4]
[1] [1]
4061t2c206na
8
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
PC-402
[4] [1]
[3] [2]
4061t2c207na
9
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
PC-402
Blank Page
10
SERVICE MANUAL Theory of Operation
LU-201
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for improve-
ment of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the corresponding
page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
LU-201
LU-201
OUTLINE
1. PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. PAPER PATH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
COMPOSITION/OPERATION
3. COMPOSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. PAPER FEED SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.1 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.1.1 Paper feed drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2.1 Paper feed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.2.2 Remaining paper detection control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. TRAY SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.1.1 Tray lift drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.1 Tray lift control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
i
CONTENTS Theory of Operation Ver.1.0 Feb. 2006
LU-201
Blank page
ii
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
OUTLINE
LU-201
1. PRODUCT SPECIFICATION
A. Type
B. Functions
C. Type of paper
Paper type *1 Plain paper, recycled paper, high quality paper of 60 to 105 g/m2
Paper size A4, 81/2 x 11
*1 Recommended paper
Plain paper Inch: Hammermill Tidal MP (20 lbs)
Metric: Konica Profi (80 g/m2), Konica Minolta Original (80 g/m2)
Recycled paper Inch: Weyehaeuser Recycled Laser Copy (20 lbs)
Metric: Nautilus (80 g/m2)
D. Maintenance
E. Machine data
F. Operating environment
Note
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.1.0 Feb. 2006
2. PAPER PATH
LU-201
[2]
16aat1c001na
2
Theory of Operation Ver.1.0 Feb. 2006 3. COMPOSITION
COMPOSITION/OPERATION
LU-201
3. COMPOSITION
16aat2c001na
3
4. PAPER FEED SECTION Theory of Operation Ver.1.0 Feb. 2006
[2]
16aat2c002na
[3]
[2]
[1]
16aat2c007na
4
Theory of Operation Ver.1.0 Feb. 2006 4. PAPER FEED SECTION
4.2 Operation
4.2.1 Paper feed control
LU-201
A. Pick-up mechanism
(1) Drive transmission
The driving force of the feed motor (M150) is transmitted to the paper feed gear /3 [4] through various gears. The
paper feed gear /3 is connected with the pick-up solenoid (SD151) [1] through the claw [2]. When SD151 is
turned OFF, the coupling between the paper feed gear /3 and the paper feed coupling gear /B [3] provided on
the front stage is disengaged and the paper feed gear /3 does not rotate. When SD151 turns ON, the claw is
released to engage the paper feed gear /3 to the paper feed coupling gear /B. In this way, the paper feed gear /
3 rotates and the driving force is transmitted to the paper feed roller unit [6] through the paper feed gear [5] to
pick up paper.
[2] [1]
16aat2c003na
5
4. PAPER FEED SECTION Theory of Operation Ver.1.0 Feb. 2006
while it is being pushed by the cam. When the paper feed gear /3 rotates, the pressure by the cam on the lift-up
shaft is released and the paper feed roller unit goes down. In this way, the paper feed roller unit goes up and
down while the paper feed gear /3 is rotating a full turn to pick up paper.
[1] [1]
16aat2c004na
6
Theory of Operation Ver.1.0 Feb. 2006 4. PAPER FEED SECTION
LU-201
paper sensors /1 (PS154) [3] and /2 (PS151) [2] and the remaining paper is detected by the combination of the
ON/OFF of these sensors. And the no paper detection in the tray is made by the paper empty sensor (PS153)
[5].
[5]
[4]
[3]
[1]
[2]
16aat2c005na
7
5. TRAY SECTION Theory of Operation Ver.1.0 Feb. 2006
5. TRAY SECTION
5.1 Drive
LU-201
[8]
[1]
[2]
[7]
[3]
[4]
[6]
[5]
16aat2c006na
8
Theory of Operation Ver.1.0 Feb. 2006 5. TRAY SECTION
5.2 Operation
5.2.1 Tray lift control
LU-201
When the upper door is closed, a parallel pin for the up drive of the lift plate is pushed out to be coupled to the
coupling of the paper lift motor (M151). Closing the upper door also turn ON the upper door interlock switch
(MS151) to supply a 24V DC to the load of the drive system. In this way, M151 turns ON to bring up the lift plate.
When the lift plate goes up and the upper limit sensor (PS152) detects the upper surface of paper, M151 turns
OFF to stop the up drive of the lift plate. When PS152 turns OFF by the paper feed operation, M151 turns ON
again to keep on bringing up the lift plate until PS152 turns ON.
When the upper door is opened, the wire is pulled to release the coupling for the up drive of the lift plate. In this
way, the lift plate goes down up to the position in which a balance is kept between the weight of paper and the
spring tension.
[4] [1]
[3] [2]
16aat2c008na
9
5. TRAY SECTION Theory of Operation Ver.1.0 Feb. 2006
LU-201
Blank page
10
SERVICE MANUAL Theory of Operation
FS-510/PU-501/
OT-601
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
FS-510/PU-501/OT-601
FS-510/PU-501/OT-601
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
1.1 FS-510 ..................................................................................................................1
1.2 PU-501..................................................................................................................3
1.3 OT-601..................................................................................................................4
2. PAPER PATH..........................................................................................................5
2.1 Exiting Paper to the Tray /1 ..................................................................................5
2.2 Exiting Paper to the Tray /2 ..................................................................................6
2.3 Exiting Paper to OT...............................................................................................7
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................9
4. DRIVE....................................................................................................................10
4.1 FS-510 ................................................................................................................10
4.2 PU-501................................................................................................................11
5. OPERATIONS .......................................................................................................12
5.1 Conveyance Section ...........................................................................................12
5.1.1 Entrance/Conveyance section.....................................................................13
5.1.2 Intermediate Conveyance Section ..............................................................14
5.1.3 Exit Conveyance Section ............................................................................15
5.2 Up/down Section.................................................................................................16
5.2.1 Up/down mechanism...................................................................................16
5.2.2 Tray Up/Down operation .............................................................................17
5.2.3 Tray Upper Limit Position Detection Mechanism ........................................18
5.2.4 Shutter Open/Close Mechanism .................................................................21
5.3 Stacker section ...................................................................................................22
5.3.1 Paper aligning mechanism (sub scan direction)..........................................22
5.3.2 Paper aligning mechanism (main scan direction)........................................23
5.3.3 Exit mechanism ...........................................................................................25
5.4 Stapling ...............................................................................................................27
5.4.1 Stapling mechanism ....................................................................................27
5.4.2 Stapling Unit moving mechanism ................................................................28
5.4.3 Stapling Position..........................................................................................28
5.4.4 Staple empty detection................................................................................29
i
CONTENTS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
6. PU-501.................................................................................................................. 30
6.1 Composition ....................................................................................................... 30
6.2 Operation............................................................................................................ 30
6.2.1 Registration mechanism ............................................................................. 30
6.2.2 Punch mechanism ...................................................................................... 31
6.2.3 Punch status detection ............................................................................... 31
6.2.4 Punch Scraps Box full detection mechanism.............................................. 32
7. OT-601.................................................................................................................. 33
7.1 Composition ....................................................................................................... 33
7.2 Operation............................................................................................................ 33
7.2.1 Overview..................................................................................................... 33
ii
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
OUTLINE
FS-510/PU-501/OT-601
1. PRODUCT SPECIFICATIONS
1.1 FS-510
A. Type
B. Functions
Modes Non sort, sort, group, sort staple, and punch (when PU-501 is mounted)
C. Paper type
(1) Non sort
(2) Sort/Group
1
1. PRODUCT SPECIFICATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
D. Stapling
F. Machine specifications
G. Operating environment
2
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
FS-510/PU-501/OT-601
1.2 PU-501
A. Type
B. Maintenance
C. Machine specifications
D. Operating environment
3
1. PRODUCT SPECIFICATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
1.3 OT-601
A. Type
B. Paper Type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
4
Theory of Operation Ver.1.0 Feb. 2006 2. PAPER PATH
2. PAPER PATH
FS-510/PU-501/OT-601
2.1 Exiting Paper to the Tray /1
[2] [1]
[3]
4349t1c001na
[1] From the main body [3] Exiting paper to the Tray /1
[2] Convey to the Tray /1
5
2. PAPER PATH Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[2] [1]
[3]
4349t1c002na
[1] From the main body [3] Exiting paper to the Tray /2
[2] Convey to the Tray /2
6
Theory of Operation Ver.1.0 Feb. 2006 2. PAPER PATH
FS-510/PU-501/OT-601
2.3 Exiting Paper to OT
[2] [1]
[3]
4349t1c003na
7
2. PAPER PATH Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
Blank Page
8
Theory of Operation Ver.1.0 Feb. 2006 3. COMPOSITION
COMPOSITION/OPERATION
FS-510/PU-501/OT-601
3. COMPOSITION
Up/down Section
Conveyance Section
PU
OT
Staple Section
4349t2c001na
5
4. DRIVE Theory of Operation Ver.1.0 Feb. 2006
4. DRIVE
FS-510/PU-501/OT-601
4.1 FS-510
[5] [6]
[4] [7]
[1]
[3]
[2]
4349t2c002na
[1] Stapler Drive Section [5] Paper Exit Opening Drive Section
[2] Exit Drive Section [6] Conveyance/Alignment Drive Section
[3] Up/down Drive Section [7] Entrance Drive Section
[4] Shutter Drive Section
6
Theory of Operation Ver.1.0 Feb. 2006 4. DRIVE
FS-510/PU-501/OT-601
4.2 PU-501
[1]
4512t2c001na
7
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
5. OPERATIONS
FS-510/PU-501/OT-601
[3]
[1]
[2]
4349t2c003na
8
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.1.1 Entrance/Conveyance section
• A paper [5] fed from the main body is conveyed to the intermediate conveyance section.
• The Entrance Motor (M3) [3] provides the drive for conveying a paper.
• When the M3 is energized, the Entrance Roller [1] and Registration Roller [2] are driven to
rotate.
• The Entrance Sensor (PS4) [4] detects a paper in the conveyance section.
[4]
[5]
[1]
[3]
[2]
4349t2c004na
9
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[4]
[1]
[3]
[2]
4349t2c005na
10
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.1.3 Exit Conveyance Section
• The paper is exited onto each of the trays.
• The Exit Motor (M1) [1] provides drive for the Exit Roller [3], Stacker Paddle [5], and Exit
Paddle [2].
[4]
[5]
[3]
[2] [1]
4349t2c006na
[1] Exit motor (M1) [4] Exit roller release motor (M6)
[2] Exit Paddle [5] Stacker Paddle
[3] Exit Roller
11
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[1]
4349t2c007na
12
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.2.2 Tray Up/Down operation
• The Tray is moved up or down by the Tray Lift Motor (M11) that turns forward or backward
to drive the front and rear belts.
• The Lower Limit Sensor (PS14) [1] detects the Tray at its lower limit position.
• The Tray Overrun Switch (SW3) [2] is provided for protection when the trays overruns nor-
mal position.
[2]
[1]
4349t2c008na
[1] Lower Limit Sensor (PS14) [2] Tray Overrun Switch (SW3)
13
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[1]
4349t2c009na
14
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
A. Tray Position Detection
• Tray position detection is controlled according to the number of times the Tray Position Sen-
sor (PS3) [1] is activated after the Lower Limit Sensor (PS14) [2] has been activated.
[2] [1]
4349t2c010na
[1] Tray Position Sensor (PS3) [2] Lower Limit Sensor (PS14)
15
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
2. After PS14 has been activated, the Up/Down Section is subjected to an ascent
motion.
3. When PS3 [1] is activated a first time after the ascent motion of the Up/Down Section
has been started, it is determined that the Up/Down Section is now located at the
paper exit opening for the Tray /1.
[1]
4349t2c011na
4. When PS3 is activated a second time after the ascent motion of the Up/Down Section
has been started, it is determined that the Up/Down Section is now located at the
paper exit opening for the Tray /2.
5. Drive is stopped when PS3 is activated with Upper Limit Sensor (PS15) of the target
tray in the activated position.
* If OT is installed, OT is at the exit port when the position sensor is activated twice and the
Tray /2 is at the exit port when the position sensor is activated three times.
16
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.2.4 Shutter Open/Close Mechanism
• The paper exit section is provided with the Shutter [3] and this Shutter is normally in the up
condition (the condition in which the Paper Exit Opening is opened). However, when the
Tray goes up and down, the Paper Exit Opening is closed to prevent an accident such as
hands getting caught in the Paper Exit Opening.
• The Shutter is opened or closed by the Shutter Motor (M12) [2] that turns a gear train for
raising or lowering the Shutter.
• The Shutter Home Sensor (PS16) [4] detects the position of the gear, thereby determining
the position of the Shutter.
• When the Shutter does not close while in the Tray up/down operation, the Shutter Switch
(SW2) [1] turns OFF to shut off a 24V DC and stop the up/down of the Tray at once.
[4]
[1]
[3] [2]
4349t2c012na
17
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[5]
[4]
[6]
[1]
[3]
[2]
4349t2c013na
18
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.3.2 Paper aligning mechanism (main scan direction)
• Aligning Plates are moved and the Paddle is rotated so as to align the paper at the stapling
position.
• The paper in the Stacker is aligned in the main scan direction by two Alignment Motors and
aligning plates.
A. Aligning plates
• The aligning plates [6] are moved to the front or rear in accordance with the paper size.
• The Alignment Sensor /Rr (PS6) [4], /Fr (PS7) [1] detects the position of each aligning plate.
[6]
[5]
[7]
[4]
[3]
[2]
[1]
4349t2c014na
19
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[5]
[1]
[2]
[4] [3]
4349t2c015na
20
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.3.3 Exit mechanism
• The paper exit roller section is provided with the Paper Holding Paddle [3] to hold the paper
exited onto the Tray while in the sort mode so that the paper does not have an uneven
edge.
• The subsequent copy set is fed out with the copy sets previously resident on the tray being
held down by the paper holding paddle.
• The Exit Paddle Home Sensor (PS11) [1], Spring Clutch [4], and Exit Paddle Solenoid (SD2)
[2] control the retracted position and paper holding position of the paper holding paddle.
[4] [1]
[3] [2]
4349t2c016na
[1] Exit Paddle Home Sensor (PS11) [3] Paper Holding Paddle
[2] Exit Paddle Solenoid (SD2) [4] Spring Clutch
21
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[4]
4349t2c017na
22
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.4 Stapling
5.4.1 Stapling mechanism
• Stapling is performed by the Stapling Unit.
• When the Stapling Motor [1] is rotated, the Clinch Arm [3] lowers. The Stapler [2] thereafter
goes up to drive a staple in the paper.
• Five different types of stapling are available: parallel front one point, parallel rear one point,
slant front one point, slant rear one point and parallel two points.
[3]
[1]
[2]
4349t2c018na
23
5. OPERATIONS Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[1]
[5]
[4]
[2]
[3]
4349t2c019na
4349t2c020na
24
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATIONS
FS-510/PU-501/OT-601
5.4.4 Staple empty detection
• Staple Empty Sensor [2] detect whether or not there are staples still left.
• When the number of staples left in the staple cartridge becomes about 20, a staple sheet
empty condition results, causing a corresponding empty message to appear on the opera-
tion panel.
• When the empty condition is detected, the corresponding empty indication is given on the
operation panel. At the same time, the Stapling Unit moves to the front.
• When a new staple cartridge is loaded, the stapling motor is energized until the Stapler
Ready Sensor [1] detects a staple, which results in the staple to be fed up to the stapling
position.
[1]
[2]
4349t2c021na
25
6. PU-501 Theory of Operation Ver.1.0 Feb. 2006
6. PU-501
FS-510/PU-501/OT-601
6.1 Composition
4512t2c002na
6.2 Operation
6.2.1 Registration mechanism
• For punch and holding operations, a loop is formed in the paper at the Registration Roller [2]
to correct skew of the paper.
• The Entrance Sensor (PS4) [1] detects the leading edge of the paper and the Registration
Roller forms a loop in the paper.
• The Registration Clutch (CL1) is then energized after a given period of time after the PS4 is
activated by the leading edge of the paper, this causes the Registration Roller to start turn-
ing.
[2]
[1]
4512t2c003na
26
Theory of Operation Ver.1.0 Feb. 2006 6. PU-501
FS-510/PU-501/OT-601
6.2.2 Punch mechanism
• After a given period of time after the Entrance Sensor (PS4) [3] has detected the trailing
edge of the paper, the Conveyance Motor (M2) of FS is deenergized and a punch hole oper-
ation is made at the trailing edge portion in each sheet of paper.
• Punch holes are made when the slide cam [1] makes a reciprocating motion, as driven by
the drive cam which is rotated by the Punch Motor (M1) [2] provided in the punch unit.
[1]
[4]
[2]
[3]
4512t2c004na
[1] [2]
[3]
4512t2c005na
27
6. PU-501 Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[1]
4512t2c006na
28
Theory of Operation Ver.1.0 Feb. 2006 7. OT-601
7. OT-601
FS-510/PU-501/OT-601
7.1 Composition
4625t2c001na
7.2 Operation
7.2.1 Overview
• Mounting the optional OT provides a total of three trays.
• The OT is attached at different positions depending on whether options SD or MT is
mounted or not.
The capacity of each tray is different depending on the position of the OT is attached.
• When the short-circuit connector shipped with OT is mounted, the machine determines that
OT has been mounted.
[5] [6]
[4] [7]
[3] [8]
[2] [1]
4625t2c002na
29
7. OT-601 Theory of Operation Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
Blank Page
30
SERVICE MANUAL Theory of Operation
FS-511/RU-502
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for improve-
ment of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the corresponding
page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
FS-511/RU-502
FS-511/RU-502
OUTLINE
1. PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 FS-511 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 RU-502 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. PAPER PATH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
COMPOSITION/OPERATION
3. COMPOSITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 FS-511 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 RU-502 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5. OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 RU conveyance section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1.1 Conveyance mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 FS conveyance section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.1 Entrance conveyance mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2.2 Gate mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2.3 Sub tray conveyance mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2.4 Main tray/handling tray conveyance mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2.5 Roller separation mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.6 Conveyance operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.3 Main tray section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3.1 Main tray up/down mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3.2 Main tray shift mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.4 Punch section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.4.1 Punch mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.4.2 Punch hole switchover mechanism (for inch area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.5 Staple section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.5.1 Alignment mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.5.2 Stapler movement mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.5.3 Stapling mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.5.4 Staple sheet empty control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
i
CONTENTS Theory of Operation Ver.1.0 Feb. 2006
FS-511/RU-502
Blank page
ii
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
OUTLINE
FS-511/RU-502
1. PRODUCT SPECIFICATION
1.1 FS-511
A. Type
B. Functions
C. Type of paper
• Maximum load capacity: (80 g/m2) when loaded with paper of the same size.
(1) Straight
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 250 sheets Sub tray —
Recycled paper B5S, A5S, and B6S
Thick paper 51/2 x 81/2S, 81/2 x 11, 91 to 130 g/m2 20 sheets
81/2 x 11S, 81/2 x 14,
Thin paper 50 to 59 g/m2
11 x 17
OHP —
transparencies
Label
Envelope
Label sheet
Letterhead
1
1. PRODUCT SPECIFICATION Theory of Operation Ver.1.0 Feb. 2006
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 50 to 130 g/m2 3000 sheets Main tray —
Recycled paper B5S (A4S or smaller)
Thick paper 81/2 x 11, 81/2 x 11S, 1500 sheets
81/2 x 14, 11 x 17 (B4 or larger)
Thin paper
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 3000 sheets Main tray 50 sheets
Recycled paper B5S (A4S or smaller)
81/2 x 11, 81/2 x 11S, 1500 sheets
81/2 x 14, 11 x 17 (B4 or larger)
(4) Punch
a. Metric/Swedish
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 — Main tray —
Recycled paper B5S Sub tray
b. Inch 2 holes
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper 81/2 x 11S, 81/2 x 14 60 to 90 g/m2 — Main tray —
Recycled paper Sub tray
c. Inch 3 holes
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper 81/2 x 11S, 11 x 17 60 to 90 g/m2 — Main tray —
Recycled paper Sub tray
2
Theory of Operation Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
D. Stapling
FS-511/RU-502
Staple filling method Dedicated staple cartridge (5000 staples)
Staple detection Available (near empty: 20 remaining staples)
Staple position *1 Rear: Diagonal 45° 1 point Metric: A3, B4, A4, B5
Front: Diagonal 45° 1 point Inch: 81/2 x 11, 11 x 17
Rear: Diagonal 28° 1 point Metric: B4, B5
Front: Diagonal 28° 1 point Inch: —
Rear: Parallel 1 point Metric: A4S, B5S
Front: Parallel 1 point Inch: 81/2 x 11S, 81/2 x 14
Side: 2 points A4, A4S, A3, B5, B5S, B4, 81/2 x 11, 81/2 x 11S,
81/2 x 14, 11 x 17
Manual staple None
*1 In case of the 1-staple mode, conduct a parallel and a skew adjustment according to the length in the
main scan direction.
Parallel: main scan direction 182 to 216 mm
Diagonal: main scan direction 216 to 297 mm
E. Punch
F. Maintenance
G. Machine data
H. Operating environment
Temperature 10 to 30 °C
Humidity 10 to 80 % RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
3
1. PRODUCT SPECIFICATION Theory of Operation Ver.1.0 Feb. 2006
1.2 RU-502
FS-511/RU-502
A. Type
B. Functions
C. Type of paper
16fat1c001na
D. Maintenance
E. Machine data
F. Operating environment
Temperature 10 to 30 °C
Humidity 20 to 80 % RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
4
Theory of Operation Ver.1.0 Feb. 2006 2. PAPER PATH
2. PAPER PATH
FS-511/RU-502
A. Non-sort mode (sub tray paper exit)
[1]
[3] [2]
4521t1c004na
Note: Even when mixed with the punch mode, the paper path is the same.
B. Non-sort/sort/group mode
[1]
[2]
4521t1c005na
Note: Even when mixed with the punch mode, the paper path is the same.
5
2. PAPER PATH Theory of Operation Ver.1.0 Feb. 2006
C. Staple mode
FS-511/RU-502
[1]
[5] [4] [3] [2]
4521t1c006na
[1] Paper exit roller (main body) [7] Paper path for other than the 1st paper of
[2] Bypass gate the 2nd and succeeding copies.
[3] Paper path for the 1st paper of the 2nd and [8] FS-511
succeeding copies [9] Main gate
[4] Stapler [10] Punch
[5] Handling tray [11] RU-502
[6] Main tray
Note: Even when the A, B or C mode mentioned above is mixed with the punch mode, the paper path is the
same.
6
Theory of Operation Ver.1.0 Feb. 2006 3. COMPOSITION
COMPOSITION/OPERATION
FS-511/RU-502
3. COMPOSITION
Conveyance
Sub tray section Punch section RU-502
Staple section
4521t2c001na
7
4. DRIVE Theory of Operation Ver.1.0 Feb. 2006
4. DRIVE
FS-511/RU-502
4.1 FS-511
[8] [1]
[7] [2]
[6]
[5]
[3]
[4]
4521t2e001na
[1] Paddle motor /Lw (M9) [8] Paper exit motor (M3)
[2] Hole punch selector motor (M14) (for inch [9] Paddle motor /Up (M15)
area) [10] Paper exit roller release motor (M13)
[3] Tray lift motor (M7) [11] Conveyance motor /Lw (M2)
[4] Shift motor (M8) [12] Conveyance motor /Up (M4)
[5] Stapler moving motor (M6) [13] Entrance conveyance motor (M1)
[6] Alignment motor (M5) [14] Punch motor (M11)
[7] Intermediate conveyance roller release
motor (M12)
8
Theory of Operation Ver.1.0 Feb. 2006 4. DRIVE
4.2 RU-502
FS-511/RU-502
[3] [4] [5]
[2]
[1]
16fat2c001na
9
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
5. OPERATION
FS-511/RU-502
[4] [5]
[1]
[3]
[2]
16fat2c003na
[1] Paper exit roller (main body) [4] Path sensor (PS2)
[2] Coupling gear [5] Conveyance roller
[3] Entrance roller (FS-511)
10
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
• The conveyance section is made up of the entrance conveyance mechanism [6] that conducts the convey-
ance drive, the main route conveyance mechanism [2], the sub tray conveyance mechanism [5], the han-
dling/paper exit conveyance mechanism [3], the gate mechanism [1] that switches the paper path and the
roller separation mechanism [4] that conducts the pressure/release of the roller.
[3]
11
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
[4]
[1]
[3] [2]
4521t2c005na
A. Control
(1) Sub tray paper exit
• When the FS start signal turns ON, the entrance conveyance motor (M1) turns ON. And it turns OFF a
specified period of time after the sub tray exit sensor (PS1) detects the trailing edge of the last paper.
(2) Sort/staple
• When the FS start signal turns ON, M1 turns ON. And it turns OFF a specified period of time after the inter-
mediate conveyance sensor (PS3) detects the trailing edge of the last paper.
12
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
[3].
• The bypass gate is driven by the bypass gate solenoid (SD1) [5].
• The main gate is driven by the main gate solenoid (SD2) [2].
[6]
[1]
[5]
[4]
[3]
[2]
4521t2c006na
13
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
A. Operation
• The paper conveyance path of the bypass gate [1] is switched over in the bypass route direction [2] when
FS-511/RU-502
the bypass gate solenoid (SD1) turns OFF and switched over in the main gate direction [10] when it turns
ON.
• The paper conveyance path of the main gate [9] is switched over in the main route direction [4] when the
main gate solenoid (SD2) turns OFF and switched over in the sub tray route direction [8] when SD2 turns
ON.
• The paper conveyance to the bypass route is used when conveying each of the 1st sheets of paper of the
2nd and succeeding copies in the staple mode to increase the handling capacity of paper even while in the
stapling operation.
4521t2c007na
B. Control
(1) Sub tray paper exit
• A specified period of time after the fusing exit sensor (PS3) of the main body turns ON and detects the lead-
ing edge of paper, the bypass gate solenoid (SD1) turns ON and the main gate solenoid (SD2) also turns
ON to switch over the conveyance path to the sub tray route.
• A specified period of time after the sub tray exit sensor (PS1) turns ON with the trailing edge of paper
detected, SD1 and SD2 turn OFF.
14
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
• The conveyance motor /Up (M4) [5] drives the conveyance roller /Up [1] and the sub tray paper exit roller [2]
to convey [3] paper [4] to the sub tray.
[5]
[1]
[4]
[3]
[2]
4521t2c008na
A. Control
(1) Sub tray paper exit (with no punch)/staple mode (with no punch)
• A specified period of time after the FS start signal turns ON, the conveyance motor /Up (M4) turns ON. And
it turns OFF a specified period of time after the sub tray exit sensor (PS1) turns OFF with the trailing edge of
paper detected.
15
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
roller [9] to convey paper in the main tray direction [4]. When rotating M2 in the reverse direction, paper is
switched back [10].
• The switch back is made for the 1st paper of each of the 2nd and succeeding copies when printing contin-
uously 2 or more copies in the staple mode to convey the 1st and the 2nd sheets of paper overlapped each
other.
• The paper exit motor (M3) [6] drives the paper exit roller [2] to convey paper in the main tray direction. When
rotating M3 in the reverse direction, paper is conveyed [3] to the handling tray [8].
• The paper conveyance to the handling tray is made while in the staple mode.
[7]
[8] [9] [10]
[6]
[1]
[5]
[4]
[3] [2]
4521t2c009na
16
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
when the bypass route conveyance sensor (PS2) [3] detects the trailing edge of the 1st paper [1] of the 2nd
copy that has been conveyed to the bypass route, M2 turns OFF.
2. A specified period of time after M2 turns OFF, M2 rotates in the reverse direction to switch back the convey-
ance [2]. And a specified period of time after that, M2 stops to stand by for the 2nd paper.
3. A specified period of time after the main route conveyance sensor (PS4) [7] detects the leading edge of the
2nd paper [8] that has been conveyed through the main route by the conveyance motor /Up (M4), M2
rotates again in the normal direction to convey the 1st and the 2nd sheets of paper overlapped each other.
4. A specified period of time after the intermediate conveyance sensor (PS3) [6] detects the trailing edge of the
last paper, M2 turns OFF.
[1]
[1] 1st paper of the 2nd copy [5] Paper of the 1st copy
[2] Switch back [6] Intermediate conveyance sensor (PS3)
[3] Bypass route conveyance sensor (PS2) [7] Main route conveyance sensor (PS4)
[4] Handling tray [8] 2nd paper of the 2nd copy
17
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
• When the FS start signal turns ON, the paper exit motor (M3) rotates in the normal direction to convey
paper to the main tray. M3 turns OFF a specified period of time after the intermediate conveyance sensor
(PS3) detects the trailing edge of the last paper.
18
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
releases the pressure from the roller.
• The intermediate conveyance roller release motor (M12) [1] drives the cam [5] to pressure/release the inter-
mediate conveyance roller [2]. The home position is detected by the roller release home sensor (PS12) [4].
• The paper exit roller release motor (M13) [8] drives the crank [7] to pressure/release the paper exit roller [3].
The home position is detected by the paper exit roller home sensor (PS13) [6].
[8]
[7]
[1]
[6]
[2]
[5]
[4]
[3]
4521t2c012na
19
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
2nd paper [4] gets to the intermediate conveyance roller [2] while in the switch back [1] of the 1st paper of
the 2nd and succeeding copies. To prevent this, release the pressure of the intermediate conveyance roller
and separate [3] the roller to get the 2 sheets of paper overlapped each other.
2. When the 2nd paper stops, the intermediate conveyance roller is pressured to convey the 2 sheets of paper
overlapped each other to the handling tray.
[1]
4521t2c013na
20
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
exit roller release motor (M13) turns ON. After the pressure of the paper exit roller [3] is released and the
paper exit roller is separated [4], M13 turns OFF.
2. After completion of the stapling operation, M13 turns ON again when the fusing exit sensor (PS3) of the main
body detects the trailing edge of the 2nd paper of the next copy. M13 pressures [7] the paper exit roller to
nip the paper [5], then M13 stops and the paper exits.
21
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
1. The 1st paper [2], the 2nd paper [3] and the 3rd paper [4] of the 1st copy are conveyed to the handling tray
[1].
2. While in the conveyance of the last paper [7] of the 1st copy, the 1st paper of the 2nd copy is conveyed [6]
to the bypass route.
[1] 4521t2c015na
3. The 1st paper [1] of the 2nd copy thus conveyed to the bypass route is switched back by the conveyance
roller /Lw [2] and the storage roller [3], and then it stops.
4. The 1st paper [4] of the 2nd copy is overlapped with the 2nd paper [5] of the 2nd copy to be conveyed.
[3] [5]
[1] 1st paper of the 2nd copy [4] 1st paper of the 2nd copy
[2] Conveyance roller /Lw [5] 2nd paper of the 2nd copy
[3] Storage roller
22
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
5. After completion of the stapling operation of the paper [1] of the 1st copy, the paper exit roller [2] is pres-
sured to exit the paper of the 1st copy. At this time, the moment the paper of the 1st copy is exited, the 1st
FS-511/RU-502
and the 2nd sheets of paper [3] of the 2nd copy are also conveyed in the main tray direction.
6. After completion of the exit of the paper [6] of the 1st copy, the pressure of the paper exit roller is released [7]
and the paper exit roller [5] rotates in the reverse direction to convey the 1st and the 2nd sheets of paper [4]
of the 2nd copy to the handling tray.
[1] Paper of the 1st copy [4] 1st and the 2nd sheets of paper of the 2nd
[2] Pressure the paper exit roller copy
[3] 1st and the 2nd sheets of paper of the 2nd [5] Paper exit roller
copy [6] Paper of the 1st copy
[7] Separation of the paper exit roller
23
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
[5]
[4]
[1]
[3]
[2]
4521t2c018na
[1] Main tray upper limit LED (LED19) [4] Main tray upper limit sensor (PS19)
[2] Tray lift motor (M7) [5] Main tray reset sensor (PS8)
[3] Main tray
A. Control
(1) While in the print operation
• While in the paper exit, when the main tray upper limit sensor (PS19) turns ON, the tray lift motor (M7)
rotates in the reverse direction to bring down the main tray. And M7 turns OFF when PS19 turns OFF. This
operation is repeated and stopped when the tray gets to the bottom according to the amount of paper
exited.
24
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
scan direction through the shift plate [3].
• The home position is detected by the shift home sensor (PS10) [2].
[1]
[5]
[4]
[2]
[3]
4521t2c019na
A. Control
(1) Sort mode
• A specified period of time after the intermediate conveyance sensor (PS3) detects the trailing edge of the
last paper of the copy, the shift motor (M8) turns ON to start the shift operation, and when the shift home
sensor (PS10) detects the shift position, M8 turn OFF.
25
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
[6]
[1]
[5]
[4]
[3]
[2] 4521t2c020na
A. Operation
1. A specified period of time after the path sensor (PS2) of the RU detects the trailing edge of paper, the con-
veyance motor /Up (M4) or conveyance motor /Lw (M2) turns OFF to stop at the prescribed punch position.
2. The punch clutch (CL1) turns ON to punch a hole.
3. M4 or M2 turns ON to convey paper.
26
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
move the lock holder [2] as necessary to select the hole positions (2 or 3 holes [1][6]).
[1]
[2] [3]
S4
[4]
[5]
[6]
S4 [7]
4521t2e002na
27
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
A. Alignment plate
• The movement of the alignment plates /Fr [5] and /Rr [1] is made by the normal/reverse drive of the align-
ment motor (M5) [2].
• The alignment plates /Fr and /Rr move with the position at the center of paper as a reference and the home
position is detected by the alignment home sensor (PS9) [4].
• The distance of movement of the alignment plate is variable according to the paper size.
• The alignment operation is made each time paper is conveyed to the handling tray.
(1) Control
1. When the intermediate conveyance sensor (PS3) detects the leading edge of the 1st paper of the job, M5
rotates in the normal direction to conduct a size movement.
2. A specified period of time after PS3 detects the trailing edge of paper, M5 rotates in the normal direction to
conduct the paper alignment. And it rotates in the reverse direction to return to the size standby position.
28
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
B. Paddle
• The paddle /Up [3] and /Lw [6] hit paper against the stopper to conduct the alignment in the sub scan
FS-511/RU-502
direction.
• The drive of the paddle /Up is made by the paddle motor /Up (M15) [5] and the paddle solenoid (SD3) [4].
• The drive of the paddle /Lw is made by the paddle motor /Lw (M9) [1].
[4] [5]
[6]
[1]
[3]
[2]
4521t2c022na
(1) Control
1. When the FS start signal turns ON, M15 and M9 also turn ON.
2. A specified period of time after the intermediate conveyance sensor (PS3) detects the leading edge of paper,
SD3 turns ON while a specified period of time.
3. A specified period of time after PS3 detects the trailing edge of the last paper of the copy, M15 and M9 turn
OFF.
4. In case of the last copy, the moment the paper exit motor (M3) turns OFF, M15 and M9 turn OFF.
29
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
• The home position is detected by the stapler home sensor (PS14) [2] and the position is decided according
to the drive amount of M6.
• The 1 stapling at the front corner is made by the stapler /Fr, the 1 stapling at the rear corner made by the
stapler /Rr, and the 2 stapling operations are made by the staplers /Fr and /Rr.
A. Control
• When the FS start signal turns ON, the stapler moving motor (M6) turns ON, and it stops at the stapling
position.
• After completion of the job, the moment the paper exit motor (M3) turns OFF, it returns to the home posi-
tion.
30
Theory of Operation Ver.1.0 Feb. 2006 5. OPERATION
FS-511/RU-502
• When the stapler motors /Rr (M16) and /Fr (M17) [1] are driven, the clinch arm [3] goes down to drive the
staple blade [2] and hit in a staple.
[3]
[1]
[2]
4521t2c024na
[1] Stapler motors /Rr, /Fr (M16, M17) [3] Clinch arm
[2] Staple blade
A. Control
• A specified period of time after the intermediate conveyance sensor (PS3) detects the trailing edge of the
last paper of the copy, the stapler motors /Rr (M16) and /Fr (M17) turn ON. After completion of the stapling
operation, the motors stop.
31
5. OPERATION Theory of Operation Ver.1.0 Feb. 2006
• The detection of the staple sheet [6] is made by the staple empty sensors /Rr (PS20) and /Fr (PS23) [4].
• The detection of the staple ready is made by the staple ready sensors /Rr (PS21) and /Fr (PS24) [2].
[5] [6]
[4] [2]
[3] [1] 4521t2c025na
[1] No staple condition [4] Staple empty sensors /Rr, /Fr (PS20, PS23)
[2] Stapler ready sensors /Rr, /Fr (PS21, PS24) [5] Stapler cartridge
[3] Staple set condition [6] Staples
32
SERVICE MANUAL Theory of Operation
SD-502
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
SD-502
SD-502
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
2. PAPER PATH..........................................................................................................2
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................3
4. DRIVE......................................................................................................................4
4.1 Half-fold section ....................................................................................................4
4.2 Saddle Stitching Section .......................................................................................4
5. OPERATIONS .........................................................................................................5
5.1 Paper Conveyance mechanism ............................................................................5
5.2 Conveyance roller pressure/release .....................................................................6
5.2.1 Pressure/release mechanism........................................................................6
5.2.2 Operation.......................................................................................................7
5.3 Stapling mechanism..............................................................................................8
5.4 Staple guide ..........................................................................................................9
5.4.1 Staple guide mechanism ...............................................................................9
5.4.2 Operation timing ............................................................................................9
5.5 Half-folding mechanism ......................................................................................10
5.5.1 Operation.....................................................................................................11
5.6 Paper guide.........................................................................................................12
5.6.1 Paper guide mechanism..............................................................................12
5.7 Tray paper detection ...........................................................................................13
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
SD-502
Blank Page
ii
Theory of Operation Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
SD-502
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
2. PAPER PATH
SD-502
4511t1c001na
2
Theory of Operation Ver.2.0 Jan. 2007 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
SD-502
Saddle-Stitching Section
Half-Fold Section
4511t2c001na
3
4. DRIVE Theory of Operation Ver.2.0 Jan. 2007
4. DRIVE
4.1 Half-fold section
SD-502
[3]
[2]
[1]
4511t2c013na
[3]
[1]
[2]
4511t2c003na
4
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5. OPERATIONS
5.1 Paper Conveyance mechanism
SD-502
• Paper is conveyed by the Exit Rollers of FS and Conveyance Roller /Up [5], /Lw [2].
• The Conveyance Motor (M8) [3] provides the drive for the Conveyance Roller /Lw [2].
• If a center stapling operation is made with a bundle papers stored in the Stacker, a bundle
papers is conveyed to the center stapling position, through a pulse control of the Exit Roller
of FS.
• A bundle papers is thereafter fed out by the Conveyance Roller /Up and /Lw.
[5]
[1]
[4]
[2]
[3]
4511t2c004na
5
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
• The Conveyance Roller /Up [1] is moved away from, or pressed up against, the Conveyance
Roller /Lw [2], when the paper is fed out as a bundle of papers.
• The Saddle Exit Home Sensor (PS18) [3] is used to control the pressure/release position of
the Conveyance Roller /Up.
[1]
[3] [2]
4511t2c005na
[1] Conveyance Roller /Up [3] Saddle Exit Home Sensor (PS18)
[2] Conveyance Roller /Lw
6
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5.2.2 Operation
1. The Conveyance Roller /Up [5] is moved up or down by the cams which are driven by
the Exit Open/Close Motor (M9) [6].
SD-502
2. When a bundle papers moves past the Conveyance Roller /Up and /Lw, the motor is
energized to press the Conveyance Roller /Up up against the Conveyance Roller /Lw,
thereby feeding a bundle papers out into the tray.
[6]
[1]
[1]
[5]
7
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
• Since the unit are for center stapling only, it is made up of the upper clincher portion [1] and
the lower stapling portion. A bundle papers moves through the space between the upper
and lower portions of the staplers.
• When stapling, the clincher portion moves downward to perform the stapling operation.
[3]
[1]
[2]
4511t2c007na
8
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
SD-502
sheet of paper is stored, thereby preventing the leading edge from contacting the Stapling
Unit and jamming.
[3]
[2] [1]
4511t2c008na
9
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
• The paper feed amount is determined for each paper size as counted from the timing when
the trailing edge is detected. Half-folding is effected as follows. Specifically, the paper
undergoes a switchback operation and is conveyed to the half-folding position as the motor
is turned backward.
• The Half-Folding Blade [3] is lowered and the center of the paper is pinched between the
Folding Rollers and this creates a crease in the paper.
• After the half-folding, the paper is conveyed by the Conveyance Roller [7] and then the Reg-
istration Roller [1] as they are driven in that order.
[7] [1]
[3]
[6] [2]
[5]
[3]
[4]
4511t2c009na
10
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5.5.1 Operation
• When the Folding Motor (M10) is energized for one cycle of operation, the Conveyance
Guides /Lw [2] are retracted to the right and left and the Half-folding Blade [3] makes one
SD-502
up-and-down reciprocating motion. In synchronism with the sequence of these operations,
the Folding Roller [1] turns one complete turn to pull the paper downward at its center.
• At the same time that the Conveyance Guides /Lw returns to their original position, the Half-
folding Blade goes up.
[1]
[3]
[2]
4511t2c010na
11
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
the paper of a large size so as to prevent it from pushing the trailing edge of the paper that
has previously been fed out.
• The Paper Guide is driven only when paper with a length of 257 mm or more will be stored.
• The Paper Guide advances when the Entrance Sensor (PS4) of FS is OFF and retracts
when the trailing edge of the paper passes the Exit Sensor (PS20).
[3]
[2]
[2] [1]
4511t2c011na
[1] Paper Guide Home Sensor (PS23) [3] Paper Guide Motor (M13)
[2] Paper Guide
12
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
SD-502
sor (PS21) [1] to detect the paper.
[1]
4511t2c012na
13
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
SD-502
Blank Page
14
SERVICE MANUAL Theory of Operation
MT-501
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
MT-501
MT-501
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
2. PAPER PATH..........................................................................................................2
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................3
4. DRIVE......................................................................................................................4
5. OPERATIONS .........................................................................................................5
5.1 Paper conveyance mechanism.............................................................................5
5.2 Paper path selection mechanism..........................................................................6
5.3 Paper detection.....................................................................................................7
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
MT-501
Blank Page
ii
Theory of Operation Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
MT-501
A. Type
B. Maintenance
C. Machine specifications
D. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
2. PAPER PATH
MT-501
4510t1c001na
2
Theory of Operation Ver.2.0 Jan. 2007 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
MT-501
4510t2c001na
3
4. DRIVE Theory of Operation Ver.2.0 Jan. 2007
4. DRIVE
MT-501
[3]
[1]
[2]
4510t2c003na
4
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
5. OPERATIONS
5.1 Paper conveyance mechanism
MT-501
• When the Mailbin is selected as the exit source, paper is fed off from the Finisher (FS-510)
and toward the Mailbin.
• Drive for the Conveyance Rollers [2] of the Mailbin is transmitted from the Conveyance
Motor (M1) [1] by way of a belt.
• As each of the Conveyance Rollers is driven, paper fed off from the Finisher is conveyed
into the Mailbin.
[1]
[2]
4510t2c004na
5
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
[1]
[2]
4510t2c005na
[1] Gate Solenoid /1, /2, /3 (SD1, SD2, SD3) [2] Gate
6
Theory of Operation Ver.2.0 Jan. 2007 5. OPERATIONS
MT-501
paper that is fed into the tray, causing the DF LED to light up green steadily to inform the
user that a sheet of paper has been fed into the tray.
• As the paper stacks up and eventually deactivates the Paper Full Sensor /1, /2, /3, /4 (PS5,
PS6, PS7, PS8) [1], at which time a paper full condition is detected.
[1]
[2]
4510t2c006na
[1] Paper Full Sensor /1, /2, /3, /4 (PS5, PS6, [2] Paper Detection Sensor /1, /2, /3, /4 (PS1,
PS7, PS8) PS2, PS3, PS4)
7
5. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
MT-501
Blank Page
8
SERVICE MANUAL Theory of Operation
JS-502
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
JS-502
JS-502
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
2. PAPER PATH..........................................................................................................2
COMPOSITION/OPERATION
3. COMPOSITION .......................................................................................................3
4. OPERATIONS .........................................................................................................4
4.1 Job Tray Conveyance/Exit ....................................................................................4
i
CONTENTS Theory of Operation Ver.2.0 Jan. 2007
JS-502
Blank Page
ii
Theory of Operation Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
JS-502
A. Type
B. Paper type
Inch:
11 x 17, 81/2 x 14,
81/2 x 11, 81/2 x 11S,
Tray 2
51/2 x 81/2S Plain Paper (56 to 90 g/m2) 100 sheets
(Job Tray)
Metric: A3, B4, A4, A4S, B5,
B5S, A5S
C. Maintenance
Maintenance None
Machine service life Same as the main body.
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
2. PAPER PATH Theory of Operation Ver.2.0 Jan. 2007
2. PAPER PATH
JS-502
[1]
4347t1c001na
2
Theory of Operation Ver.2.0 Jan. 2007 3. COMPOSITION
COMPOSITION/OPERATION
3. COMPOSITION
JS-502
Job Separator section Switchback Unit section
4347t2c001na
3
4. OPERATIONS Theory of Operation Ver.2.0 Jan. 2007
4. OPERATIONS
4.1 Job Tray Conveyance/Exit
JS-502
• The Switchback Unit functions to convey paper through, and feed it out from, the Job Tray.
• The paper sensor section of the Job Tray is mounted to the Switchback Unit, thereby detect-
ing paper.
• When paper stacks up on the Tray [3], the actuator [2] is pushed up by the paper, indicating
that there is paper at the exit port.
[1]
[3]
[2]
4347t2c002na
4
© 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
Printed in Japan
Use of this manual should be strictly supervised to avoid
CC36GA-M-TE2
disclosure of confidential information.
FIELD SERVICE TOTAL CONTENTS
DF-607
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 19
* For particulars, see the contents of DF-607.
PC-202
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 15
* For particulars, see the contents of PC-202.
PC-402
OUTLINE ........................................................................................................................ 1
MAINTENANCE.............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 19
* For particulars, see the contents of PC-402.
i
LU-201
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 21
* For particulars, see the contents of LU-201.
FS-510/PU-501/OT-601
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 21
* For particulars, see the contents of FS-510/PU-501/OT-601.
FS-511/RU-502
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 5
ADJUSTMENT/SETTING ............................................................................................. 17
* For particulars, see the contents of FS-511/RU-502.
SD-502
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
ADJUSTMENT/SETTING ............................................................................................. 23
* For particulars, see the contents of SD-502.
MT-501
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
* For particulars, see the contents of MT-501.
JS-502
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
* For particulars, see the contents of JS-502.
IC-204
OUTLINE ........................................................................................................................ 1
MAINTENANCE ............................................................................................................. 3
ADJUSTMENT / SETTING ............................................................................................. 7
TROUBLESHOOTING ................................................................................................... 9
* For particulars, see the contents of IC-204.
ii
SAFETY AND IMPORTANT WARNING ITEMS
IMPORTANT NOTICE
Because of possible hazards to an inexperienced person servicing this product as well as
the risk of damage to the product, Konica Minolta Business Technologies, INC. (hereafter
called the KMBT) strongly recommends that all servicing be performed only by KMBT-
trained service technicians.
Changes may have been made to this product to improve its performance after this Service
Manual was printed. Accordingly, KMBT does not warrant, either explicitly or implicitly, that
the information contained in this Service Manual is complete and accurate.
The user of this Service Manual must assume all risks of personal injury and/or damage to
the product while servicing the product for which this Service Manual is intended.
Therefore, this Service Manual must be carefully read before doing service work both in the
course of technical training and even after that, for performing maintenance and control of
the product properly.
Keep this Service Manual also for future service.
Symbols used for safety and important warning items are defined as follows:
S-1
SAFETY AND IMPORTANT WARNING ITEMS
SAFETY WARNINGS
[1] MODIFICATIONS NOT AUTHORIZED BY KONICA MINOLTA
BUSINESS TECHNOLOGIES, INC.
Konica Minolta brand products are renowned for their high reliability. This reliability is
achieved through high-quality design and a solid service network.
Product design is a highly complicated and delicate process where numerous mechanical,
physical, and electrical aspects have to be taken into consideration, with the aim of arriving
at proper tolerances and safety factors. For this reason, unauthorized modifications involve
a high risk of degradation in performance and safety. Such modifications are therefore
strictly prohibited. The points listed below are not exhaustive, but they illustrate the reason-
ing behind this policy.
Prohibited Actions
DANGER
• Using any cables or power cord not specified by KMBT.
S-2
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Use power supply cord set which meets the following
criteria:
AC230V
- provided with a plug having configuration intended for
the connection to wall outlet appropriate for the prod-
uct's rated voltage and current, and
- the plug has pin/terminal(s) for grounding, and
- provided with three-conductor cable having enough cur-
rent capacity, and
AC208V 240V
- the cord set meets regulatory requirements for the area.
Use of inadequate cord set leads to fire or electric shock.
• Attach power plug which meets the following criteria:
- having configuration intended for the connection to wall
outlet appropriate for the product's rated voltage and
current, and
- the plug has pin/terminal(s) for grounding, and
- meets regulatory requirements for the area.
Use of inadequate cord set leads to the product connect-
ing to inadequate power supply (voltage, current capac-
ity, grounding), and may result in fire or electric shock.
S-3
SAFETY AND IMPORTANT WARNING ITEMS
1. Power Supply
WARNING
• Check that mains voltage is as specified.
Connection to wrong voltage supply may result in fire or
electric shock. ?V
• Plug the power cord into the dedicated wall outlet with a
capacity greater than the maximum power consumption.
If excessive current flows in the wall outlet, fire may
result.
S-4
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Check whether the product is grounded properly.
If current leakage occurs in an ungrounded product, you
may suffer electric shock while operating the product.
Connect power plug to grounded wall outlet.
WARNING
• When using the power cord set (inlet type) that came with
this product, make sure the connector is securely inserted
in the inlet of the product.
When securing measure is provided, secure the cord with
the fixture properly.
If the power cord (inlet type) is not connected to the prod-
uct securely, a contact problem may lead to increased
resistance, overheating, and risk of fire.
S-5
SAFETY AND IMPORTANT WARNING ITEMS
WARNING
• Check whether dust is collected around the power plug
and wall outlet.
Using the power plug and wall outlet without removing
dust may result in fire.
• Do not insert the power plug into the wall outlet with a wet
hand.
The risk of electric shock exists.
• When unplugging the power cord, grasp the plug, not the
cable.
The cable may be broken, leading to a risk of fire and
electric shock.
Wiring
WARNING
• Never use multi-plug adapters to plug multiple power
cords in the same outlet.
If used, the risk of fire exists.
S-6
SAFETY AND IMPORTANT WARNING ITEMS
2. Installation Requirements
WARNING
• Do not place the product near flammable materials or vol-
atile materials that may catch fire.
A risk of fire exists.
WARNING
• When the product is not used over an extended period of
time (holidays, etc.), switch it off and unplug the power
cord.
Dust collected around the power plug and outlet may
cause fire.
Ventilation
CAUTION
• The product generates ozone gas during operation, but it
will not be harmful to the human body.
If a bad smell of ozone is present in the following cases,
ventilate the room.
a. When the product is used in a poorly ventilated room
b. When taking a lot of copies
c. When using multiple products at the same time
Fixing
CAUTION
• Be sure to lock the caster stoppers.
In the case of an earthquake and so on, the product may
slide, leading to a injury.
S-7
SAFETY AND IMPORTANT WARNING ITEMS
CAUTION
• Before conducting an inspection, read all relevant docu-
mentation (service manual, technical notices, etc.) and
proceed with the inspection following the prescribed pro-
cedure in safety clothes, using only the prescribed tools.
Do not make any adjustment not described in the docu-
mentation.
If the prescribed procedure or tool is not used, the prod-
uct may break and a risk of injury or fire exists.
WARNING
• Take every care when making adjustments or performing
an operation check with the product powered.
If you make adjustments or perform an operation check
with the external cover detached, you may touch live or
high-voltage parts or you may be caught in moving gears
or the timing belt, leading to a risk of injury.
S-8
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• Check the exterior and frame for edges, burrs, and other
damages.
The user or CE may be injured.
S-9
SAFETY AND IMPORTANT WARNING ITEMS
Safety Checkpoints
WARNING
• When replacing a lithium battery, replace it with a new lith-
ium battery specified in the Parts Guide Manual. Dispose
of the used lithium battery using the method specified by
local authority.
Improper replacement can cause explosion.
• Make sure the wiring cannot come into contact with sharp
edges, burrs, or other pointed parts.
Current can leak, leading to a risk of electric shock or
fire.
• Make sure that all screws, components, wiring, connec-
tors, etc. that were removed for safety check and mainte-
nance have been reinstalled in the original location. (Pay
special attention to forgotten connectors, pinched cables,
forgotten screws, etc.)
A risk of product trouble, electric shock, and fire exists.
Handling of Consumables
WARNING
• Toner and developer are not harmful substances, but care
must be taken not to breathe excessive amounts or let the
substances come into contact with eyes, etc. It may be
stimulative.
If the substances get in the eye, rinse with plenty of water
immediately. When symptoms are noticeable, consult a
physician.
S-10
SAFETY AND IMPORTANT WARNING ITEMS
Handling of Consumables
WARNING
• Never throw the used cartridge and toner into fire.
You may be burned due to dust explosion.
CAUTION
• Unplug the power cord from the wall outlet.
Isopropyl alcohol and acetone are highly flammable and
must be handled with care. A risk of fire exists.
S-11
SAFETY INFORMATION
SAFETY INFORMATION
IMPORTANT NOTICE
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Admin-
istration implemented regulations for laser products manufactured since August 1, 1976.
Compliance is mandatory for products marketed in the United States.
This copier is certified as a "Class 1" laser product under the U.S.
Department of Health and Human Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. Since radiation emit-
ted inside this copier is completely confined within protective housings and external covers,
the laser beam cannot escape during any phase of normal user operation.
S-12
SAFETY INFORMATION
50gap0e001na
S-13
SAFETY INFORMATION
50gap0e002na
CAUTION:
• You may be burned or injured if you touch any area that you are advised by any
caution label to keep yourself away from. Do not remove caution labels. And also,
when the caution label is peeled off or soiled and cannot be seen clearly, replace
it with a new caution label.
S-14
MEASURES TO TAKE IN CASE OF AN ACCIDENT
S-15
MEASURES TO TAKE IN CASE OF AN ACCIDENT
Blank Page
S-16
Composition of the service manual
This service manual consists of the following sections and chapters:
This section gives, as information required by the CE at the site (or at the customer's
premise), a rough outline of the service schedule and its details, maintenance steps, the
object and role of each adjustment, error codes and supplementary information.
The details of items with an asterisk "*" are described only in the service manual of
the main body.
C-1
Notation of the service manual
A. Product name
In this manual, each of the products is described as follows:
B. Brand name
The company names and product names mentioned in this manual are the brand name or
the registered trademark of each company.
C-2
Classification Load symbol Ex. of signal name Description
24V Power to drive the motor
CONT Drive signal
DRV1
Motor M
DRV2
Drive signals of two kinds
D1
D2
_U
_V
_W
Drive signals (control signals) of three kinds
DRV1
DRV2
DRV3
D1
D2
D3
D4
DRV A
DRV A
DRV B Drive signals (control signals) of four kinds
DRV B Motor, phases A and B control signals
A
Motor M /A
B
/B
AB
BB
CLK, PLL PLL control signal
LCK, Lock, LD PLL lock signal
FR Forward/reverse rotation signal
EM, Lock, LCK, LD Motor lock abnormality
BLK Drive brake signal
P/S Power/stop
S/S
Operating load start/stop signal
SS
CW/CCW, F/R Rotational direction switching signal
ENB Effective signal
TEMP_ER Motor temperature abnormality detection signal
24V Power to drive the fan motor
CONT, DRIVE Drive signal
Fan FM
HL Speed control signal (2 speeds)
EM, Lock, LCK, FEM Detection signal
Others TH1.S, ANG Analog signal
C-3
Classification Load symbol Ex. of signal name Description
SG, S.GND, S_GND Signal ground
Ground
PG, P.GND Power ground
DCD Data carrier detection
SIN Serial input
SOUT Serial output
DTR Data terminal operation available
GND Signal ground (earth)
Serial com-
DSR, DSET Data set ready
munication
RTS Transmission request signal
CTS Consent transmission signal
RI Ring indicator
TXD Serial transmission data
RXD Serial reception data
<Example>
C-4
SERVICE MANUAL Field Service
500/420/360
Main body
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
bizhub 500/420/360
bizhub 500/420/360
OUTLINE
1. SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. PRODUCT SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MAINTENANCE
3. PERIODIC CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.1 Main body (bizhub 500) / DF / PC / LU / FS / MT / SD / RU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.2 Main body (bizhub 420) / DF / PC / LU / FS / MT / SD / RU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1.3 Main body (bizhub 360) / DF / PC / LU / FS / MT / SD / RU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Maintenance item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2.1 Main body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2.2 DF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.3 PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.4 LU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.5 FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.6 MT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.7 SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.8 RU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3 Replacement parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3.1 Periodically replacement parts list (bizhub 500/420) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3.2 Periodically replacement parts list (bizhub 360) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.4 Life value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4.1 Life value of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.5 Maintenance procedure of the external section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5.1 Replacing the ozone filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5.2 Replacing the filter cover assy and the suction filter /A assy . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.5.3 Replacing the paper exit suction filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.6 Maintenance procedure of the write section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.6.1 Replacing the write unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.7 Maintenance procedure of the photosensitive material section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.7.1 Replacing the drum unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.7.2 Replacing the drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.8 Maintenance procedure of the transfer/separation corona section. . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.8.1 Replacing the transfer/separation corona unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.9 Maintenance procedure of the developing section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.9.1 Replacing the developing unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.9.2 Replacing developer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.10 Maintenance procedure of the toner supply section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.10.1 Replacing the filter mounting plate assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.10.2 Replacing the suction cover /2 assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.11 Cleaning/toner recycle section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.11.1 Replacing the cleaning blade assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.12 Maintenance procedure of the paper feed section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
i
CONTENTS Field Service Ver.2.0 Jan. 2007
ii
Field Service Ver.2.0 Jan. 2007 CONTENTS
bizhub 500/420/360
6.1.3 Developing unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
6.1.4 Drum unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
6.2 List of parts to be disassembled and reassembled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
6.3 Disassembling/assembling procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
6.3.1 Removing/reinstalling the rear cover /1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
6.3.2 Removing/reinstalling the rear cover /2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
6.3.3 Removing/reinstalling the rear cover /3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
6.3.4 Removing/reinstalling the right cover /Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
6.3.5 Removing/reinstalling the right cover /Lw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
6.3.6 Removing/reinstalling the left cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
6.3.7 Removing/reinstalling the front door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
6.3.8 Removing/reinstalling the original glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
6.3.9 Removing/reinstalling the upper covers /Fr and /Lt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
6.3.10 Removing/reinstalling the upper cover /Rr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
6.3.11 Removing/reinstalling the front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
6.3.12 Removing/reinstalling the operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
6.3.13 Removing/reinstalling the CCD unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
6.3.14 Replacing the exposure lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
6.3.15 Removing/reinstalling the exposure unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
6.3.16 Stretching the scanner wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
6.3.17 Removing/reinstalling the toner supply unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
6.3.18 Removing/reinstalling the trays 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
6.4 Option counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
6.4.1 Configuration of the key counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
6.4.2 Installation procedure of the key counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
ADJUSTMENT/SETTING
7. HOW TO USE THE ADJUSTMENT/SETTING SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
7.1 Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
8. UTILITY MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
8.1 List of utility mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
9. LIST OF ADJUSTMENT ITEMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
10. SERVICE MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
10.1 List of service mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
10.2 Setting Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
10.2.1 Start and exit of the service mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
10.3 Machine Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
10.3.1 Print Positioning: Leading Edge (Printer Area). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
10.3.2 Print Positioning: Side Edge (Printer Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
10.3.3 Paper Feed Direction Adj. (Printer Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
10.3.4 Printer Resist Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
10.3.5 Bypass Tray Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
10.3.6 Image Position: Leading Edge (Scan Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
10.3.7 Image Position: Side Edge (Scan Area). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
10.3.8 Cross Direction Adjustment (Scan Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
10.3.9 Feed Direction Adjustment (Scan Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
10.3.10 Lead Edge Erase Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
10.3.11 Non-Image Area Erase Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
10.4 Imaging Process Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
iii
CONTENTS Field Service Ver.2.0 Jan. 2007
iv
Field Service Ver.2.0 Jan. 2007 CONTENTS
bizhub 500/420/360
10.10Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
10.11CS Remote Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
10.11.1 Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
10.11.2 Setting Up the CS Remote Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
10.11.3 Software SW setting for CS Remote Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
10.11.4 Setup confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
10.11.5 Calling the Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
10.11.6 Calling the Center from the Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
10.11.7 Checking the transmission log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
10.11.8 Detail on settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
10.11.9 List of the CS Remote Care error code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
10.11.10Troubleshooting for CS Remote Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
10.12System 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
10.12.1 Data Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
10.12.2 Paper Size Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
10.12.3 DipSW Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
10.12.4 ISW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
10.12.5 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
10.12.6 Network FAX Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
10.12.7 Trouble Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
10.12.8 Internet ISW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
10.13List Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
10.13.1 List output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
10.14Test Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
10.14.1 Test pattern list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
10.14.2 Test pattern output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
10.14.3 Running Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
10.15Fax setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
10.16Enhanced Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
10.16.1 List of the security setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
10.16.2 Start and termination of the security mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
10.16.3 CE Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
10.16.4 Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
10.16.5 Administrator Feature Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
10.16.6 CE Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
10.17Billing Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
10.17.1 List of the billing setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
10.17.2 Start and termination of the billing setting mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
10.17.3 Counter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
10.17.4 Management Function Choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
11. MECHANICAL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
11.1 Mis-centering adjustment of the trays 1 and 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
11.2 Mis-centering adjustment of the bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
TROUBLESHOOTING
12. JAM CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
12.1 Jam code list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
13. MALFUNCTION CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
13.1 Malfunction code list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
v
CONTENTS Field Service Ver.2.0 Jan. 2007
APPENDIX
bizhub 500/420/360
vi
Field Service Ver.2.0 Jan. 2007 CONTENTS
17.7 LU
bizhub 500/420/360
17.8 FS
17.8.1 FS-510/PU-501
17.8.2 FS-511
17.9 SD
17.10MT
vii
CONTENTS Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Blank page
viii
Field Service Ver.2.0 Jan. 2007 1. SYSTEM CONFIGURATION
OUTLINE
bizhub 500/420/360
1. SYSTEM CONFIGURATION
A. System configuration
[5]
[1] [6]
[2] [7]
[3] [8]
[4] [9]
[22]
[21]
[20]
[19] [11]
[14]
[17] [15]
[18]
[10] [12]
[16]
[10] [13]
50gat1e001nb
*1 See "6.4 Option counter" in Field Service bizhub 500/420/360 main body for details.
*2 Dehumidifier heater is set up as service part.
*3 Swedish punch kit G is for Europe only.
1 1
1. SYSTEM CONFIGURATION Field Service Ver.2.0 Jan. 2007
Note
• Any combination other than those listed below is not available.
2
Field Service Ver.2.0 Jan. 2007 2. PRODUCT SPECIFICATIONS
2. PRODUCT SPECIFICATIONS
bizhub 500/420/360
A. Type
3
2. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
B. Functions
bizhub 500/420/360
4 1
Field Service Ver.2.0 Jan. 2007 2. PRODUCT SPECIFICATIONS
C. Type of paper
bizhub 500/420/360
Plain paper *1 All trays High quality paper of 60 to 90 g/m2
Special paper *2 Bypass feed only OHP film, label paper *3, blueprint master paper *3
High quality paper of 50 to 59 g/m2 (thin paper)
All trays High quality paper of 91 to 105 g/m2 (thick paper)
Bypass feed only High quality paper of 106 to 210 g/m2 (thick paper)
D. Maintenance
E. Machine data
1 5
2. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
F. Operating environment
bizhub 500/420/360
Temperature 10 to 30 °C
Humidity 10 to 80%RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
6
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
MAINTENANCE
bizhub 500/420/360
3. PERIODIC CHECK
3.1 Schedule
3.1.1 Main body (bizhub 500) / DF / PC / LU / FS / MT / SD / RU
7
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Every 250,000prints
Maintenance 1 z z z z z z z 7 times
MT
8
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Guarantee period: 5 years or 1,800,000 prints
Every 225,000prints
Maintenance 1 z z z z z z z 7 times
MT
1 9
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• For the replacement procedure of periodically replaced parts, see "3.5 Maintenance procedure of
the external section" to "3.15 Maintenance procedure of the fusing section".
• The alcohol described in this section represents the isopropyl alchol.
10 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
classification Cleaning Check Lubrication Replacement Tools used
8 Bypass tray Feed roller z Alcohol/cleaning pad
section
Separation roller z Alcohol/cleaning pad
9 Fusing Fusing roller 1 z
section 50GA5303
Fusing pressure roller 1 z
50GA5304
Fusing web 1 z
50GA-540
Fusing counter reset
Heat insulating sleeve /A 2 z
26NA5372
Fusing bearing /Up 2 z
26NA5371
Fusing bearing /Lw 2 z
50GA5359
Fusing driven roller /A 2 z
assy
4040R706
Fusing driven roller /B 2 z
assy
4040R707
Fusing sensor z Alcohol/cleaning pad
Fusing claw z Alcohol/cleaning pad
Thermostat z Alcohol/cleaning pad
10 Paper reverse Paper exit suction filter 1 z
section 50GA4406
11 Registration Paper dust removing z Blower brush
section brush
Registration roller /Rt z Alcohol/cleaning pad
Registration roller /Lt z Alcohol/cleaning pad
Loop roller z Alcohol/cleaning pad
Reflective sensor z Blower brush
12 Final check Paper through, Image z
check
PM count reset z
Exterior cleaning z
1 11
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
12 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
No. Unit Description Quantity Implementation classification Materials
classification Cleaning Check Lubrication Replacement Tools used
1 Registration Registration bearing /Rt 2 z
section 26NA4536
Registration bearing /Lt 2 z
26NA4537
Loop roller 1 z
50GA3865
Registration roller /Rt 1 z
50GA3848
Loop bearing 2 z
26NA4082
2 Write section Write unit 1 z
50GA-650
3.2.2 DF
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
1 13
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
3.2.3 PC
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
14 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
3.2.4 LU
bizhub 500/420/360
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
3.2.5 FS
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
1 15
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
3.2.6 MT
bizhub 500/420/360
3.2.7 SD
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
3.2.8 RU
A. Maintenance 1 (Every 250,000 prints (bizhub500/420) / Every 225,000 prints (bizhub360))
16 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.3.1 Periodically replacement parts list (bizhub 500/420)
Note
• For the replacement procedure of periodically replaced parts, see "3.5 Maintenance procedure of
the external section" to "3.15 Maintenance procedure of the fusing section".
• The parts count No. given in the table below represents the number of the fixed parts number in
the Service mode.
A. Main body
No. Classification Part name Part number Qt. Actual replace- Parts count Page
ment cycle No. referred to
1 Photo con- Drum DR510 1 250,000 P.31
2 ductor section Cleaning blade assy 50GA-209 1 250,000 P.45
3 Drum unit (without drum) 50GA-200 1 750,000 P.30
4 Transfer/ Transfer/separation unit 50GA-260 1 500,000 P.37
separation
section
5 Developing Developer DV511 1 250,000 P.39
6 section Developing unit 50GA-300 1 750,000 P.38
7 Main body Filter mounting plate assy 50GA-336 1 250,000 P.42
8 Ozon filter 50GA1031 1 250,000 P.22
9 Suction filter /A assy 40LAR705 1 250,000 P.23
10 Filter cover assy 50GA-314 2 250,000 P.23
11 Suction cover /2 assy 50GA-311 4 250,000 P.43
12 Paper feed Pick-up roller 40303005 2 300,000 P.47
section P.54
13 Feed roller 40303005 2 300,000 P.47
P.54
14 Separation roller assy 40300151 2 300,000 P.52
(Tray 1, 2) P.61
15 Bypass tray Paper feed roller 41313001 1 200,000 P.69
16 section Separation roller assy 40340151 1 200,000 P.66
17 Registration Loop roller 50GA3865 1 1,250,000 P.73
18 section Registration roller /Rt 50GA3848 1 1,250,000 P.73
19 Registration bearing /Rt 26NA4536 2 1,250,000 P.73
20 Registration bearing /Lt 26NA4537 2 1,250,000 P.73
21 Loop bearing 26NA4082 1 1,250,000 P.73
22 Fusing Fusing roller 50GE5303 1 250,000 P.91
23 section Fusing pressure roller 50GA5304 1 250,000 P.91
24 Fusing web 50GA-540 1 250,000 P.85
25 Heat insulating sleeve /A 26NA5372 2 250,000 P.91
26 Fusing bearing /Up 26NA5371 2 250,000 P.91
27 Fusing bearing /Lw 50GA5359 2 250,000 P.91
1 17
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
No. Classification Part name Part number Qt. Actual replace- Parts count Page
bizhub 500/420/360
B. Option
No. Classification Part name Part number Qt. Actual replace- Parts count Page
ment cycle No. referred to
1 DF Pick-up roller 43445003 1 200,000 *1
2 Feed roller 45823014 1 200,000 *1
3 Separation roller 45823047 1 200,000 *2
4 PC Pick-up roller 40303005 1 300,000 *3
5 Feed roller 40303005 1 300,000 *4
6 Separation roller assy 40300151 1 300,000 *5
7 LU Pick-up rubber 40LA4009 1 200,000 *6
8 Feed rubber 26NA4011 1 200,000 *6
9 Separation rubber 26NA4012 1 200,000 *7
18 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Note
• For the replacement procedure of periodically replaced parts, see "3.5 Maintenance procedure of
the external section" to "3.15 Maintenance procedure of the fusing section".
• The parts count No. given in the table below represents the number of the fixed parts number in
the Service mode.
A. Main body
No. Classification Part name Part number Qt. Actual replace- Parts count Page
ment cycle No. referred to
1 Photo con- Drum DR510 1 225,000 P.31
2 ductor section Cleaning blade assy 50GA-209 1 225,000 P.45
3 Drum unit (without drum) 50GA-200 1 675,000 P.30
4 Transfer/ Transfer/separation unit 50GA-260 1 450,000 P.37
separation
section
5 Developing Developer DV511 1 225,000 P.39
6 section Developing unit 50GA-300 1 675,000 P.38
7 Main body Filter mounting plate assy 50GA-336 1 225,000 P.42
8 Ozon filter 50GA1031 1 225,000 P.22
9 Suction filter /A assy 40LAR705 1 225,000 P.23
10 Filter cover assy 50GA-314 2 225,000 P.23
11 Suction cover /2 assy 50GA-311 4 225,000 P.43
12 Paper feed Pick-up roller 40303005 2 300,000 P.47
section P.54
13 Feed roller 40303005 2 300,000 P.47
P.54
14 Separation roller assy 40300151 2 300,000 P.52
(Tray 1, 2) P.61
15 Bypass tray Paper feed roller 41313001 1 200,000 P.69
16 section Separation roller assy 40340151 1 200,000 P.66
17 Registration Loop roller 50GA3865 1 900,000 P.73
18 section Registration roller /Rt 50GA3848 1 900,000 P.73
19 Registration bearing /Rt 26NA4536 2 900,000 P.73
20 Registration bearing /Lt 26NA4537 2 900,000 P.73
21 Loop bearing 26NA4082 1 900,000 P.73
22 Fusing Fusing roller 50GA5303 1 225,000 P.91
23 section Fusing pressure roller 50GA5304 1 225,000 P.91
24 Fusing web 50GA-540 1 225,000 P.85
25 Heat insulating sleeve /A 26NA5372 2 225,000 P.91
26 Fusing bearing /Up 26NA5371 2 225,000 P.91
27 Fusing bearing /Lw 50GA5359 2 225,000 P.91
28 Fusing sensor assy 50GA-544 1 450,000 P.95
29 Fuse holder assy 26NA-535 1 450,000 P.97
1 19
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
No. Classification Part name Part number Qt. Actual replace- Parts count Page
bizhub 500/420/360
B. Option
No. Classification Part name Part number Qt. Actual replace- Parts count Page
ment cycle No. referred to
1 DF Pick-up roller 43445003 1 200,000 *1
2 Feed roller 45823014 1 200,000 *1
3 Separation roller 45823047 1 200,000 *2
4 PC Pick-up roller 40303005 1 300,000 *3
5 Feed roller 40303005 1 300,000 *4
6 Separation roller assy 40300151 1 300,000 *5
7 LU Pick-up rubber 40LA4009 1 200,000 *6
8 Feed rubber 26NA4011 1 200,000 *6
9 Separation rubber 26NA4012 1 200,000 *7
20 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.4.1 Life value of materials
1 21
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Remove the right cover /Up.
(See P.142)
2. Remove the ozone filter [1].
Note
• When removing the ozone filter, be sure to
pull it out by holding it at the section indicated
by [2].
[1]
[2]
50gaf2c014na
22 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
3.5.2 Replacing the filter cover assy and the suction filter /A assy
bizhub 500/420/360
A. Periodically replaced parts/cycle
• Filter cover assy : Every 250,000 prints *1
: Every 225,000 prints *2
• Suction filter /A assy : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Remove the screw [1] and then remove the filter
cover assy [2].
[1]
[2]
50gaf2c015na
[1] 50gaf2c016na
1 23
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
bizhub 500/420/360
[1] 50gaf2c017na
24
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Paper exit suction filter : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Remove the screw [1] and then remove the paper
exit suction filter cover [2].
[1]
[2]
50gaf2c018na
50gaf2c019na
1 25
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Warning
• Be sure not to turn on the write unit with it shifted from its regular installation position.
• Be absolutely sure not to remove the write unit cover. Otherwise, laser beams get in your eyes and
you may suffer loss of sight.
• Be absolutely sure not to remove the write unit for about 2 minutes after you turn off the main
power switch (SW1) or the power switch (SW2).
B. Procedure
1. Remove the developing unit from the main body.
[1]
(See P.38)
2. Remove the drum unit from the main body.
(See P.30)
3. Pull out the dust-proof glass cleaning rod [1].
4. Remove the cleaning knob [4] from the dust-proof
glass cleaning rod [1] by rotating it in the arrow-
marked direction [3] with the section indicated by
[2] as a fulcrum.
5. Replace the dust-proof glass cleaning rod [1] to its
original position.
Note
[2] • Be sure to push in fully the dust-proof glass
cleaning rod [1] so that it does not come in
contact with the main body frame when
[4] removing the unit.
[3]
50gaf2c020na
26 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
[1]
write cover [2].
Note
• When installing the write cover, be sure to set
the projections [3] at 3 places into each of the
holes [4] of the frame.
50gaf2c022na
Note
• When installing the write section mounting
member assy [2], be sure to install it so that
the spring [3] gets straight.
27
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When removing the write unit, be sure to
avoid touching the dust-proof glass.
[3] [2]
[1]
50gaf2c024na
Note
• When installing the write unit [1], be sure to
take note of the position into which the dust-
proof sheet /A [2] is inserted.
• When checking the insertion of the sheet, be
sure to check it with the drum unit removed.
[1] [2]
50gaf2c025na
28
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
Note
bizhub 500/420/360
[1] • When installing the write unit, be sure to set
the projections [1] at 2 places provided on the
bottom to the 2 holes [2] of the main body
frame for positioning.
[2] 50gaf2c026na
29
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When removing the drum unit, be sure to hold it at both ends.
• When removing the drum unit, be sure to avoid holding it at the separation claw unit section.
• Be sure to avoid touching the drum with bare hands, and also be careful not to damage it.
• Be sure to avoid turning the drum in any direction other than in the specified direction.
• When storing the drum unit, be sure to store it in the dark place with a drum cover attached.
B. Procedure
1. Open ADU.
(See P.142)
2. Pull the lock release lever [1] to open the convey-
ance unit [2].
50gaf2c028na
30 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Note
• Be sure to avoid touching the drum and the cleaning blade with bare hands, and also be careful
not to damage them.
• When storing the drum, be sure to store it in the dark place with a drum cover attached.
• When installing the drum and the cleaning blade, be sure to apply setting powder to the circumfer-
ence of the drum and the cleaning blade, regardless of these parts being new or used ones.
• When setting powder is applied to the drum, be sure to conduct the following operations before
installing the drum unit to the main body.
1) With the charging corona unit removed, rotate the drum one full turn (to prevent setting powder
from splashing onto the charging corona unit and the image from getting defective.)
2) When installing a new drum, be sure to reset the drum counter in the service mode. Failing to
reset it may result in image fogging and toner splashing. (See P.210)
1 31
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
bizhub 500/420/360
Note
• When installing the cleaning rod, be sure to
take note of the direction of the C-clip.
[2]
[3]
50gaf2c029na
32
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
5. Open the lock lever [2] and remove the charging
corona unit [3].
[1] [3]
[2]
50gaf2c030na
33
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When installing the drum shaft, be sure to
[2] [2]
insert the drum shaft until the shaft mounting
plate comes into contact firmly with it as
shown in the drawing.
[3] [3]
8. Remove the 2 screws [4] and then remove the
[1] bearing [5].
[2]
[3]
[4]
[5]
50gaf2c031na
34
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
10. Hold the drum [3] at both ends and remove it.
Note
[1] • When removing the drum, be careful not to
damage the photosensitive surface.
• When removing the drum, be careful not to hit
it against the metal frame section [4] of the
cleaning blade.
[3]
[4]
[2]
50gaf2c032na
35
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
bizhub 500/420/360
[1]
• When installing the drum, using the attached
jig [2] with the drum unit cover [1] before
[2] installing the charging corona unit, rotate the
drum 1 full turn in the arrow-marked direction
[3]. And then check to see if setting powder is
not scraped off, and also if the toner collec-
tion sheet and the cleaning blade do not
turned up.
[2]
[3]
50gaf2c033na
36
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.8.1 Replacing the transfer/separation corona unit
A. Periodically replaced part/cycle
• Transfer/separation corona unit : Every 500,000 prints *1
: Every 450,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Open ADU.
[3]
(See P.142)
2. Open the conveyance unit.
(See P.30)
3. Release the lock levers [1] and [2] and remove the
transfer/separation corona unit [3].
4. Reinstall the above parts following the removal
steps in reverse.
1 37
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Open the front door [1].
2. Loosen the screw [2] and remove the developing
unit [3].
3. Reinstall the above parts following the removal
steps in reverse.
[3] [1]
[2]
50gaf2c035na
38 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Developer : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Remove the developing unit from the main body.
[2]
(See P.38)
2. Release the locks [1] at 2 places and remove the
developing unit cover /1 [2].
[1]
50gaf2c036na
1 39
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
bizhub 500/420/360
[3] [2]
50gaf2c037na
40
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
[1] [4]
ing gear [2] in the arrow-marked direction [3] to
discharge thoroughly developer in the developing
unit [1].
4. Clean developer and toner that adhere to the
developing roller [4].
Note
• Be absolutely sure not to turn the developing
gear [2] in any direction other than in the
arrow-marked direction [3]. (Never rotate it
clockwise as seen from the direction indi-
cated by [5].)
• If there remains any used developer on the
developing roller, this may cause image fog-
ging.
[5] [3] [2] 50gaf2c041na
41
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Remove the developing unit from the main body.
[2] [1]
(See P.38)
2. Open ADU.
(See P.142)
3. Open the conveyance unit.
(See P.30)
4. Remove the drum unit from the main body.
(See P.30)
5. Release the lock levers [1] at 2 places and remove
the filter mounting plate assy [2].
6. Reinstall the above parts following the removal
procedure in reverse.
[1] [2]
50gaf2c043na
42 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Suction cover /2 assy : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Remove the developing unit from the main body.
(See P.38)
2. Open ADU.
(See P.142)
3. Open the conveyance unit.
(See P.30)
4. Remove the drum unit from the main body.
[3] (See P.30)
5. Remove the screw [1] and then remove the rail [2].
Note
• When installing the rail, be sure first to insert
the tip into the notch [3].
[2]
[1]
50gaf2c044na
1 43
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[1]
7. Reinstall the above parts following the removal
steps in reverse.
50gaf2c045na
44
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.11.1 Replacing the cleaning blade assy
Note
• Be sure to avoid touching the edge section of the cleaning blade assy with bare hands.
• When installing the cleaning blade assy, be sure to apply setting powder to the circumference of
the drum and the cleaning blade, regardless of these parts being new or used ones.
• When setting powder is applied to the drum, be sure to conduct the following operations before
installing the drum unit to the main body.
1) With the charging corona unit removed, rotate the drum 1 full turn (to prevent setting powder
from splashing onto the charging corona unit and the image from getting defective.)
B. Procedure
1. Remove the developing unit from the main body.
[1] (See P.38)
2. Open ADU.
(See P.142)
3. Open the conveyance unit.
(See P.30)
4. Remove the drum unit from the main body.
(See P.30)
5. Remove the drum from the drum unit.
[2] (See P.31)
50gaf2c046na
6. Remove the 2 screws [1] and then remove the
cleaning blade presser plate [2].
50gaf2c047na
1 45
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
bizhub 500/420/360
[1]
• When installing the cleaning blade assy [1], be
sure to insert the transparent sheet section
[2] of the unit the between the collection
screw [3] and the collection paddle [4].
[3] [2]
[4]
[1]
50gaf2c048na
46
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.12.1 Replacing the feed roller/pick-up roller (tray 1)
A. Periodically replaced parts/cycle
• Feed roller : Every 750,000 prints (Actual replacement cycle: Every 300,000 prints) *1
: Every 675,000 prints (Actual replacement cycle: Every 300,000 prints) *2
• Pick-up roller : Every 750,000 prints (Actual replacement cycle: Every 300,000 prints) *1
: Every 675,000 prints (Actual replacement cycle: Every 300,000 prints) *2
*1 500/420
*2 360
B. Procedure
1. Remove the front cover.
(See P.148)
2. Remove the tray 1.
(See P.163)
3. Remove the connector [1] and the 2 screws [2],
and then remove the paper feed unit /1 [3].
[2]
[1]
[3]
[2]
50gaf2c108na
1 47
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
bizhub 500/420/360
[3] [2]
• When installing the paper feed unit /1 [1], be
sure to set the shafts [2] and [3] to the holes
[4] and [5].
[5] [1]
[4] 50gaf2c109na
48
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
separation roller unit /1 [2].
[3][4]
Note
• When installing the separation roller unit /1,
[1]
be sure to set the projections [3], 1 each, to
each of the holes [4].
[2] [3][4]
[1]
50gaf2c110na
[3]
[1]
[4]
50gaf2c111na
49
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
ing [2].
[1] 8. Detach the hook [4] of the spring [3] from the
oblong hole [5].
9. Remove the bearing [6] and then remove the
paper feed roller unit [7].
[2]
Note
• When attaching the spring, be sure to put the
hook into the oblong hole (not into the round
hole [8]).
[8] [7]
[5]
[4]
[6]
[3]
50gaf2c161na
10. Remove the E-ring [1] and then remove the bear-
[4] [1]
ing [2].
11. Remove the bearing [3] and then remove the feed
roller assy [4].
[2]
[3] 50gaf2c162na
50
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
12. Remove the C-ring [1] and then remove the feed
bizhub 500/420/360
roller [2].
[1]
[2] 50gaf2c163na
[1] [2]
[1]
[3] [2] 50gaf2c164na
15. Remove the C-ring [1] and then remove the pick-
[2] [1] up roller [2].
16. Reinstall the above parts following the removal
steps in reverse.
50gaf2c113na
51
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Remove the tray 1.
[1] (See P.163)
2. Remove the paper feed unit /1.
(See P.47)
3. Remove the separation roller unit /1.
(See P.47)
4. Remove the 2 screws [1] and then remove the
[2] [3] separation roller mounting plate assy [2].
50gaf2c117na
Note
• When installing the separation roller mount-
ing plate assy, be sure to fasten it with screws
while pressing it in the arrow-marked direc-
tion [3].
5. Remove the 2 C-rings [1] and pull out the shaft [2].
6. Remove the separation roller mounting plate [3].
[1]
Note
• When removing the separation roller mount-
[2] ing plate, be careful that the spring [4] does
[1] not get lost since it is apt to come off.
• When installing the separation roller mount-
ing plate, be sure to install it so that it comes
under the projection [5].
52 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
8. Remove the C-ring [2] and then remove the sepa-
ration roller assy [3].
9. Reinstall the above parts following the removal
steps in reverse.
[1] [3]
[2]
50gaf2c119na
53
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Remove the bypass unit.
(See P.63)
2. Pull out the tray 2 [1].
[1]
50gaf2c120na
[3]
54 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
conveyance roller cover [2].
[1]
[1]
50gaf2c123na
55
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[2]
8. Remove the 3 screws [2] and then remove the
paper feed unit /2 [3].
[1]
[3]
[2]
50gaf2c124na
56
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
separation roller unit /2 [2].
[1]
Note
• When installing the separation roller unit /2,
be sure to set the projection [3] to the hole [4].
[3] [4]
[2] [3]
50gaf2c126na
57
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
13. Remove the C-ring [2] and then remove the feed
clutch /2 (CL5) [3].
Note
• When installing CL5, be sure to set the stop-
per [4] to the guide plate [5].
[3]
[2] [5]
[4]
[1]
50gaf2c127na
58
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
14. Detach the hook [2] of the spring [1] from the
bizhub 500/420/360
[3] oblong hole [3].
[7]
15. Remove the C-rings [4], 1 each, and then remove
the 2 bearings [5].
16. Remove the paper feed roller unit [6].
[2]
Note
• When attaching the spring, be sure to put the
[1] hook into the oblong hole (not into the round
hole [7]).
[6]
[4]
[4] [5] 50gaf2c165na
17. Remove the E-ring [1] and then remove the bear-
[4] [1]
ing [2].
18. Remove the bearing [3] and then remove the feed
roller assy [4].
59
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
19. Remove the C-ring [1] and then remove the feed
bizhub 500/420/360
roller [2].
[1]
[2] 50gaf2c167na
[1] [2]
[1]
[3] [2] 50gaf2c168na
22. Remove the C-ring [1] and then remove the pick-
[2] [1] up roller [2].
23. Reinstall the above parts following the removal
steps in reverse.
50gaf2c129na
60
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Separation roller assy : Every 750,000 prints (Actual replacement cycle: Every 300,000 prints) *1
: Every 675,000 prints (Actual replacement cycle: Every 300,000 prints) *2
*1 500/420
*2 360
B. Procedure
1. Remove the bypass unit.
(See P.63)
2. Pull out the tray 2.
3. Remove the vertical conveyance door.
(See P.54)
4. Remove the conveyance roller cover.
(See P.54)
5. Remove the paper feed guide /2.
[1] [2] [1]
(See P.54)
6. Remove the paper feed unit /2.
(See P.54)
7. Remove the separation roller unit /2.
(See P.54)
8. Remove the 2 screws [1] and then remove the
separation roller mounting plate assy [2].
Note
[3] • When installing the separation roller mount-
50gaf2c133na
ing plate assy, be sure to fasten it with screws
while pressing it in the arrow-marked direc-
tion [3].
1 61
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
9. Remove the 2 C-rings [1] and pull out the shaft [2].
bizhub 500/420/360
Note
• When removing the separation roller mount-
[2] ing plate, be careful that the spring [4] does
[1] not get lost since it is apt to come off.
• When installing the separation roller mount-
ing plate, be sure to install it so that it comes
under the projection [5].
[1] [3]
[2]
50gaf2c135na
62
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
3.13.1 Removing/reinstalling the bypass unit
A. Procedure
1. Remove the right cover /Lw.
[2] [1]
(See P.143)
2. Remove the screw [1] and then remove the
bypass cover /Fr [2].
3. Loosen the screw [3] and then remove the screw
[4] to remove the bypass cover /Rr [5].
[5]
63
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[4]
5. Remove the screw [2] and then remove the
ground terminal [3].
6. Remove the 5 screws [4] and then remove the
bypass unit [5].
[5]
[4] 50gaf2c002na
64
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
steps in reverse.
8. After installing the bypass unit, open the tray 2
paper feed guide [1] and the bypass feed guide [2]
in the arrow-marked direction [3] to check to see if
they operate smoothly.
50gaf2c003na
65
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When replacing the separation roller assy, be sure also to replace the feed roller at the same time.
B. Procedure
1. Remove the bypass unit.
[2] [2]
(See P.63)
2. Remove the 2 springs [1].
3. Remove the 5 screws [2].
[2]
[1] 50gaf2c004na
66 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
4. Detach the hook [1] from the hole [2] and remove
bizhub 500/420/360
[3] the push-up plate assy [3].
[1] [2]
50gaf2c005na
Note
[1] [3] [1]
• When installing the push-up plate assy, be
sure to install it while pressing the push-up
plate [3] so that each of the springs [1] does
not comes off each cross-headed boss [2].
67
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[2] [1]
separation roller fixing plate assy [2].
50gaf2c007na
Note
• When removing the holder [1], the spring [4]
provided under the holder is apt to come off.
Be careful that it does not get lost.
• When installing the holder [1], be sure to
install it so that it comes under the projection
[5].
[2] 50gaf2c008na
[2] 50gaf2c009na
68
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Feed roller : Every 750,000 prints (Actual replacement cycle: Every 300,000 prints) *1
: Every 675,000 prints (Actual replacement cycle: Every 300,000 prints) *2
*1 500/420
*2 360
Note
• When replacing the feed roller, be sure also to replace the separation roller assy at the same time.
B. Procedure
1. Remove the bypass unit.
(See P.63)
2. Remove the push-up plate assy.
(See P.66)
3. Press the conveyance guide [1] in the arrow-
marked direction [2] to remove the support axis [3]
from the hole [4], and then remove the convey-
ance guide.
[1] 50gaf2c010na
1 69
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[3]
then remove the paper roller cover [3].
Note
• When installing CL6, be sure to set the stop-
per [3] to the guide plate [4].
[4] 50gaf2c170na
[1] 50gaf2c171na
70
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
ing [2].
8. Remove the bearing [3] and slide the shaft [4].
50gaf2c172na
Note
• When installing the feed roller, be sure to take
note of the direction of the arrow mark [4].
50gaf2c173na
71
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Open ADU.
[2]
(See P.142)
2. Open the conveyance unit.
(See P.30)
3. Remove the developing unit from the main body.
(See P.38)
4. Remove the drum unit from the main body.
(See P.30)
5. Remove the suction cover /2 assy.
(See P.43)
6. With the lever [1] pulled, remove the paper dust
removing brush [2] and clean the paper dust
removing brush with a blower brush.
[1]
7. Reinstall the above parts following the removal
50gaf2c174na
steps in reverse.
72 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
3.14.2 Replacing the loop roller, the loop bearing, the registration roller /Rt, and the registration
bizhub 500/420/360
bearings /Rt and /Lt
A. Periodically replaced parts/cycle
• Loop roller : Every 1,250,000 prints *1
: Every 900,000 prints *2
• Loop bearing : Every 1,250,000 prints *1
: Every 900,000 prints *2
• Registration roller /Rt : Every 1,250,000 prints *1
: Every 900,000 prints *2
• Registration bearing /Rt : Every 1,250,000 prints *1
: Every 900,000 prints *2
• Registration bearing /Lt : Every 1,250,000 prints *1
: Every 900,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Open ADU.
(See P.142)
2. Open the conveyance unit.
(See P.30)
3. Remove the developing unit from the main body.
(See P.38)
4. Remove the drum unit from the main body.
(See P.30)
5. Remove the suction cover /2 assy.
(See P.43)
6. Remove the 2 connectors [1].
[1]
50gaf2c175na
1 73
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When installing the ADU drive assy, be sure to
set the stopper [4] of the registration clutch
(CL1) [3] to the guide plate [5].
[2] [1]
[3]
[1]
[3]
[4]
[5]
50gaf2c154na
74
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
9. Remove the screw [2].
10. Remove the C-clip [3] and slide CL1 [4] in the
arrow-marked direction [5].
11. Remove the 2 C-clips [6] to release the bearing
[7].
Note
• When installing the 2 C-clips [6], be sure to
install them with their collars come face to
face each other.
12. Remove the C-clip [8] and then remove the bear-
ing [9].
[10] [3] [4] [7] 13. Remove the registration unit [10].
75
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When installing CL2, be sure to set the stop-
per [5] to the screw [6].
16. Remove the screw [7] and then remove the regis-
tration main body assy [8].
[8]
50gaf2c156na
76
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
loop bearings [2].
18. Remove the loop roller [3].
19. Remove the 2 loop bearings from the loop roller.
50gaf2c157na
77
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When attaching the spring, be sure to couple
the hook [5] of the spring at the position as
shown in the drawing left.
78
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
the 2 registration bearings /Rt [2].
24. Remove the registration roller /Rt [3].
25. Reinstall the above parts following the removal
steps in reverse.
[2] [1]
50gaf2c159na
79
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Caution
• Since the fusing section gets hot immediately after turning off the main power switch (SW1) or the
power switch (SW2), you may suffer a burn. Be sure to conduct the operations when the tempera-
ture goes down sufficiently.
A. Procedure
1. Open ADU.
[2] [1]
(See P.142)
2. Remove the right cover /Up.
(See P.142)
3. Open the conveyance unit.
(See P.30)
4. Loosen the screw [1] and remove the front auxil-
iary cover [2].
50gaf2c085na
80
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
[4] 6. Remove the screw [2] and then remove the filter
cover [3].
7. Remove the 2 screws [4].
[1]
8. Loosen the 2 screws [5]. And after sliding the
entire reverse unit [6] in the arrow-marked direc-
tion [7], tilt the front side in the arrow-marked
direction [8] for removal.
[4]
50gaf2c086na
81
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[2]
fusing unit [2].
Note
• When lifting the fusing unit, be sure to hold it
at both ends.
• When installing/removing it, be careful not to
damage rollers.
[1] 50gaf2c087na
B. Procedure
1. Remove the fusing unit.
(See P.80)
2. Remove the C-clip [1].
3. Open the fusing front guide assy [2].
82 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
[1] 50gaf2c089na
83
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When installing the fusing claw assy, be care-
[1] ful not to neglect attaching the connector [4].
• When installing the fusing claw assy, be sure
to insert the positioning sections [6] at 2
places into each of the projections [7].
• When installing the fusing claw assy, be care-
ful not to damage the roller surface with the
tip of the claw.
[2] [5] [4] 8. Reinstall the above parts following the removal
steps in reverse.
50gaf2c091na
84 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced part/cycle
• Fusing web : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
1. Remove the fusing unit.
[4] [2]
(See P.80)
2. Remove the fusing claw assy.
(See P.82)
3. Remove the screw [1].
4. Remove the 5 screws [2].
5. Apply pressure from the inside of the ducts [3] at 2
places to release the lock and remove the fusing
web [4].
Note
• When installing the fusing web, be sure to
[1] [5] [3] install the screw [1] first.
50gaf2c092na
Note
[2]
• When installing the fusing web, be sure to
insert the projections [1] at 2 places into the
positioning holes [2].
[1] 50gaf2c093na
1 85
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[1]
86
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
A. Periodically replaced parts/cycle
• Fusing driven roller assy /A : Every 250,000 prints *1
: Every 225,000 prints *2
• Fusing driven roller assy /B : Every 250,000 prints *1
: Every 225,000 prints *2
*1 500/420
*2 360
B. Procedure
Note
[8] • When removing the fusing unit cover /Rr, be
careful that the internal gear does not fall
down.
Note
• When installing the fusing casing [8], be sure
to install first the screw [5] (upper side).
1 87
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• The gear [4] is not fixed. Take care when mov-
ing it.
[1]
[4]
50gaf2c096na
88
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Note
• Be careful not to touch the lamp sections of L2 and L3 with bare hands. When touched, be sure to
clean them with a roller cleaner.
A. Procedure
1. Remove the fusing unit.
[1]
(See P.80)
2. Remove the fusing claw assy from the fusing unit.
(See P.82)
3. Remove the fusing web from the fusing unit.
(See P.85)
4. Remove the fusing casing.
(See P.87)
5. Remove the fastons [1] and [2], 2 each.
Note
• When removing the faston, be sure to remove
it by holding the connector section. Be abso-
lutely sure not to pull out by holding the wiring
harness section.
[2] 50gaf2c097na
89
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[8] [1]
6. Remove the screw [1] and then remove the lamp
bizhub 500/420/360
Note
• When installing each of the fusing heater
lamps, be sure to set the projections [6] of
each lamp to the notch [7] of the lamp fixing
plate /Fr [2].
• After installing each of the fusing heater
lamps, be sure to check to see if it is not in
touch with the inner face of the fusing roller
[8].
[5] [3] [2] • Be sure to install the fusing heater lamp L2 [3]
(main) on the upper side with L3 [4] (sub) on
the lower side.
Note
• When installing the fusing heater lamp, be
sure to take note of the direction of installa-
tion.
Lamp Destination
North America Europe/Others
[7] [6] [4] 50gaf2c098na
Fr Rr Fr Rr
L2 Red Red Blue Blue
L3 Red Black Blue Black
90
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
3.15.6 Replacing the fusing roller, the fusing pressure roller, the heat insulating sleeve /A, the fusing
bizhub 500/420/360
bearings /Up and /Lw and the fusing input gear assy
A. Periodically replaced parts/cycle
• Fusing roller : Every 250,000 prints *1
: Every 225,000 prints *2
• Fusing pressure roller : Every 250,000 prints *1
: Every 225,000 prints *2
• Heat insulating sleeve /A : Every 250,000 prints *1
: Every 225,000 prints *2
• Fusing bearing /Up : Every 250,000 prints *1
: Every 225,000 prints *2
• Fusing bearing /Lw : Every 250,000 prints *1
: Every 225,000 prints *2
• Fusing input gear assy : Every 500,000 prints *1
: Every 450,000 prints *2
*1 500/420
*2 360
1 91
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
bizhub 500/420/360
Note
• When installing the fusing input gear assy, be
sure to set the D cut section [6] of the shaft
[5] to the D cut hole [8] of the frame [7].
[9] 50gaf2c099na
92 1
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
[5] [2] [1]
[2].
10. Remove the heat insulating sleeve /A [3] and the
fusing bearing /Up [4].
Note
• When installing the heat insulating sleeve /A
and the fusing bearing /Up, be sure to install
[4] [3] [10]
them with their respective collar [5] outside.
• When installing the heat insulating sleeve /A,
be sure to apply Multemp FF-RM to its inside
and outside peripheries.
11. Remove the C-ring [6] and then remove the heat
insulating sleeve /A [7] and the fusing bearing /Up
[8].
Note
• When installing the heat insulating sleeve /A
[12] [11] [7] [8] and the fusing bearing /Up, be sure to install
them with their respective collar [9] outside.
• When installing the heat insulating sleeve /A,
be sure to apply Multemp FF-RM to its inside
and outside peripheries.
[1] 50gaf2c101na
1 93
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
Note
• When installing the fusing bearing /Lw, be
sure to install it with its collar section [3]
inside. Coat the cored bar section with
grease.
[1] 50gaf2c102na
94
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Caution
• After installing the fusing sensor assy, be sure to check to see if it is in touch with the fusing roller.
B. Procedure
1. Remove the fusing unit.
[1] [3] [2]
(See P.80)
2. Remove the fusing claw assy from the fusing unit.
(See P.82)
3. Remove the fusing web from the fusing unit.
(See P.85)
4. Remove the fusing casing.
(See P.87)
5. Remove the fusing heater lamps /1 (L2) and /2
(L3).
(See P.89)
6. Remove the fusing roller and the fusing pressure
roller.
[4] (See P.91)
7. Remove the faston [1].
Note
• When removing the faston, be sure to remove
it by holding its base section. Be absolutely
sure not to pull it out by holding the wiring
harness section.
50gaf2c104na
1 95
3. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[2]
the fusing sensor assy [2].
Note
• When installing the fusing sensor assy, be
careful not to deform the sensor section.
• After installing the fusing sensor assy, be sure
to check to see if the wiring harness is not in
touch with the fusing roller.
Caution
• After installing the fusing sensor assy, be sure
[1] 50gaf2c105na
to check to see if the thermistors /1 (TH1) and
/2 (TH2) are in touch with the fusing roller.
Note
[1]
• The fusing sensor assy is made up of TH1 and
TH2. The sections of TH1 and TH2 have been
adjusted when they were assembled, and be
absolutely sure not to loosen the screw [1].
50gaf2c106na
96
Field Service Ver.2.0 Jan. 2007 3. PERIODIC CHECK
bizhub 500/420/360
Caution
• After installing the fuse holder assy, be sure to check to see if it is in touch with the fusing roller.
B. Procedure
1. Remove the fusing unit. (See P.80)
[1] [4] [3]
2. Remove the fusing claw assy from the fusing unit.
(See P.82)
3. Remove the fusing web from the fusing unit.
(See P.85)
4. Remove the fusing casing. (See P.87)
5. Remove the fusing heater lamps /1 (L2) and /2
(L3). (See P.89)
6. Remove the fusing roller and the fusing pressure
roller. (See P.91)
7. Pull out the web support assy /2. (See P.95)
8. Remove the faston [1].
[2] 50gaf2c107na
Note
• When removing the faston, be sure to remove
it by holding its base section. Be absolutely
sure not to pull it out by holding the wiring
harness section.
Note
• When installing the fuse holder assy, be care-
ful not to deform the thermostat section.
• After installing the fuse holder assy, be sure
to check to see if the wiring harness is not in
touch with the fusing roller.
Caution
• After installing the fuse holder assy, be sure
to check to see if the thermostat (TS) [4] is in
touch with the fusing roller.
1 97
4. SERVICE TOOLS Field Service Ver.2.0 Jan. 2007
4. SERVICE TOOLS
bizhub 500/420/360
98
Field Service Ver.2.0 Jan. 2007 4. SERVICE TOOLS
bizhub 500/420/360
Parts No. Name Shape Quantity Remark
26NA2134 Drum rotation mem- 1 Mounted to the drum
ber unit
99
4. SERVICE TOOLS Field Service Ver.2.0 Jan. 2007
00VE-100 Tester 1
4.3 Materials
A. Item
100 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
5. FIRMWARE VERSION UP
bizhub 500/420/360
5.1 ISW
5.1.1 Outline
A. ISW (In-System Writer)
The operation to rewrite firmware stored in the flash ROM that is built in each control board in the main body
with the board left built in the main body is called an ISW. Executing ISW allows you to upgrade the firmware ver-
sion without replacing the board, or install the latest firmware when replacing the board. As a tool to execute
ISW, there is ISWTrns (PC software) that rewrites firmware with the personal computer (PC) locally connected to
the main body.
(1) ISWTrns
This is a software for Windows to rewrite flash ROM of the main body and rewrites firmware with the main body
and the PC locally connected with a parallel cable or UBS cable.
Note
• When upgrading the ISWTrns version, be sure to uninstall the old version of ISWTrns before install-
ing the new version of ISWTrns. When installed by overwriting, this may result in the installation by
the USB driver unavailable.
• When the main body uses the USB to conduct the ISW, it is necessary to install the USB driver of
the ISWTrns. For procedure for installation, see "5.2.3 Usage of the ISWTrns A. Installation of the
USB driver (Windows2000/XP)." After installing the ISWTrns, be absolutely sure to install the USB
driver of the ISWTrns.
(See P.106)
PC Overall control board (OACB) Printer control board (PRCB) DF control board (DFCB)
FS control board (FSCB)
FAX control board (FK-502)
When executing the ISW over the entire system, be sure to execute it in the order given below. (To minimize the
occurrence of troubles resulting from the mismatch of the firmware version)
Note
• When replacing the OACB, be sure to conduct the ISW of the MFP controller first. When the firm-
ware of the MFP controller is not contained in the OACB, no display is shown on the touch panel.
• The finisher above refers to the FS-510. The ISW of the FS-511 is conducted by changing the
EPROM.
101
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
Following the description given below, be sure to make appropriate settings on the main body side to conduct
the operations of the firmware version upgrade and writing.
C. When writing the firmware afresh (When replacing the board or when failed in rewriting the firm-
ware)
For the overall control board (OACB), when something is wrong with the firmware or no firmware is written, the
normal start-up cannot be made. In a case like this, when the power switch is ON, the power LED turns ON with
nothing shown on the touch panel, and the system is placed in the firmware stand-by mode.
For other boards, when the firmware of the MFP controller is normal and something is wrong with other firm-
ware, an ISW error is shown on the touch panel section when the power is turned ON.
102 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
5.2 ISWTrns
bizhub 500/420/360
5.2.1 Specifications
A. ISWTrns (PC software)
(1) Operating environment of the software
• OS: Windows95/98/98SE/Me/NT4.0/2000/XP
• CPU: Pentium 75 MHz or above
• Memory: 16 MB or more
• Free space in hard disk: 100 MB or more
• Others: PC provided with parallel (printer) or USB interface (type A)
Item Specifications
Board to be rewritten Overall control board (OACB), Printer control board (PRCB), FAX control
board (FK-502), FS control board (FSCB), DF control board (DFCB)
Rewritable firmware MFP controller
Operation panel message data
Image controller
FAX board controller 1
FAX board controller 2
Finisher
ADU
Note
• For boards other than the above, ROM replacement is required.
103
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
(1) Procedure
Step Operation
1 Start the PC.
2 Copy the setup files to the PC and double click the [Setup.exe] icon to start the install program.
Note
• When there remains the ISWTrns of the old version, uninstall the old version first, and
then install the new version.
3 "ISWTrns setup screen"
Following the instructions on the screen, check the folder to which an installation is made, and then
click [Next].
Note
• For default, "C:\Program Files\KONICA MINOLTA\ISWTrns" is set as a folder to which an
installation is made.
• When changing the folder to which an installation is made, click [Browse] and specify
the folder.
4 Following the instructions on the screen, check the folder to which the ISWTrns program is stored
and then click [Next].
Note
• For default, "ISWTrns" is set as a folder to which an installation is made.
• When changing the folder to which an installation is made, enter the folder name
directly, or select one from the existing folder displayed.
5 Following the instructions on the screen, click [Finish].
6 The installation of the ISWTrns program is automatically completed.
7 Select [ISWTrns] from the start menu or double-click the [ISWTrns] icon on the desk top to start up
the ISWTrns program.
104
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
Step Operation
bizhub 500/420/360
8 "ISWTrns screen"
Click [OK] to set the storage folder of the firmware.
Note
• This screen is shown only when the program is started for the first time after installing
the ISWTrns.
9 "Option screen"
Click [Make Folder]
Note
• A folder (C:\Program Files\KONICA MINOLTA\ISWTrns) into which the ISWTrns program
is installed as a storage folder is set by default.
• When changing the storage folder, click [Browse] to specify it arbitrarily or enter it
directly in the editor box in full path.
• Clicking [Make Folder] creates hierarchical folders with the storage folder set above as
a route.
10 "Option screen"
Click [OK].
Note
• This operation allows the data folder created in step 9 to be stored in the INI file of the
ISWTrns program.
105
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
(1) Procedure
Step Operation
1 Connect the USB cable to the main body.
2 Connect the USB cable to the USB connector of the USB.
3 From the screen below, select "Install from a list or specific location," and then click [Next].
The driver is stored in the C:\WINDOWS\Drivers\Usb.
4 In the "Please choose your search and installation options" screen, select "Don't search. I will choose
the driver to install," and then click [Next].
5 Check the driver name and click [Next].
Driver name: KONICA MINOLTA 500/420/360 USB Driver for ISW
6 When the "Completing the Found New Hardware Wizard" screen is displayed, click [Finish] to exit the
installation.
7 Check the "Device Manager screen" to see if the USB driver has been correctly installed.
Driver name: KONICA MINOLTA 500/420/360 USB Driver for ISW
106 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
B. Firmware copy
bizhub 500/420/360
By using the ISWTrns, firmware that transfers it to the main body is copied into the specified folder.
(1) Procedure
Step Operation
1 Start the PC.
2 Select [ISWTrns] from the start menu or double click the [ISWTrns] icon on the desktop to start up the
ISWTrns.
3 Click [Option (O)] from the menu and then click [Option (O)].
4 "Option screen"
Click [Data Copy].
Note
• The folder selected is shown in the upper display section of the "Original Files."
• In the lower display section of the "Original Files," the firmware related files stored in the
folder are shown.
6 Select a file you want to copy from the lower display section of the "Original Files."
Note
• The plural transferred files (rewritten data) can be selected.
• When copying all of the files that are displayed, skip this step and proceed to the step 7.
107
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
Step Operation
bizhub 500/420/360
7 Click [Copy] automatically copies the selected file into the specified folder created by installing the
ISWTrns.
Note
• When copying all of the files that are displayed in the lower display section of the "Origi-
nal Files", click [Copy All] instead of [Copy].
• In the upper display section of the "Copied Files", a folder name created at the setup of
the ISWTrns is displayed.
• In the list shown in the lower display section of the "Copied Files," files the copy of
which has been successfully completed are listed in full path. In the "Failed to Copy
Files", files the copy of which have been failed are listed. As the causes of failure, follow-
ing are considered.
A. There exists a file of the same name and "O/W" is not checked.
B. A folder into which a file is stored is not found.
C. An overwrite is made on an overwrite-prohibited file.
• When changing a file that is currently stored into a new data, click the overwrite check
box to make a check mark.
8 After completion of copy, click [Refresh].
9 Click [Cancel] to get back to "option screen."
10 "Option screen"
Click [OK].
Step Operation
1 Enter the Service mode.
2 Press the [Firmware Version] in "Service mode screen".
3 Indication of "Firmware Version screen"
108
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
Open the Service mode of the main body to put the ISW transfer in the standby condition.
Step Operation
1 Enter the Service mode.
2 Press the [System 2] in "Service mode screen."
3 Press the [ISW] in the sub menu shown to the right of the screen.
4 "Board Type Selection screen"
109
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
1) Procedure
Step Operation
1 Turn OFF the power of the main body.
2 Turn OFF the power of the PC.
3 Connect the parallel cable [2] to the IEEE1284 port [1] of the PC.
[1]
[2]
50gaf2c176na
4 Connect the parallel cable [1] of the PC to the ISW connector [2] of the main body.
[2]
[1]
50gaf2c177na
110
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
Preparations are made of the following when a connection is made.
• PC which firmware have been copied.
• UBS cable
1) Procedure
Step Operation
1 Connect the UBS cable [2] to the USB port [1] of the PC.
[1]
[2]
50gaf2c178na
Note
• Be sure to connect the UBS cable to the ISW connector of the main body after the set-
ting is made in the following condition.
111
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
E. Rewriting of firmware
bizhub 500/420/360
(1) Relationship between the ISW and the display of the operation panel
When the ISWTrns starts up, the main screen is displayed. In the main screen, the transmission file (firmware) is
selected, the information is diplayed, the checksum and the transmission file are sent out. For detailed informa-
tion of the functions, refer to the following.
[2] [3]
[4]
[1]
[5]
[6]
[7]
[9]
[8]
[10]
112
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
[9] [FileCheck]
bizhub 500/420/360
With a transmission file displayed in "SendFile info" of [8], press this key to calculate the file checksum
(checksum of the entire file) of the displayed transmission file and show a result beside the transmission file.
And also, compare the result of the checksum with the checksum file attached to the firmware and display
the obtained result in the form shown below.
"OK": Accord
"NG": Not accord
"??": Checksum file (*.sum) not found
[10] [FileSend]
The transmission of the transferred file is started.
(2) Procedure
e.g.: When conducting the ISW of the MFP controller for bizhub 500.
Step Operation
1 Start the ISWTrns program.
2 Click [Set-up (S)] from the menu and then click [Communication setting (C)].
3 "Set Communication screen"
Select a port through which the transmission is made and click [OK].
Note
• When [Parallel] is selected, be sure also to specify [Port].
4 Select the machine type, the destination and the board types.
• Machine type: 500, Country: EU, Board type: CONTROL (ALL)
5 The data to be used is displayed in the version selection frame and the send file information frame.
113
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
Step Operation
bizhub 500/420/360
6 Press the [FileCheck] to check if the data to be used has any problem.
9 When a connection is made with a USB cable, connect the USB cable [2] to the USB connector [1] of
the main body.
[1]
[2]
50gaf2c179na
Note
• Be sure to press the start key before connecting the USB cable. When connecting the
USB cable before the start key is pressed, the main body is put in the stand-by position
for the print data with no ISW data accepted.
10 Click [FileSend] of the ISWTrns.
114
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
Step Operation
bizhub 500/420/360
11 The following window is displayed on the PC while in the data transfer.
12 When the data transfer is completed, the following window is displayed and click [OK].
"ISWTrns"
13 When the data writing is completed, the reboot is automatically made to show the trouble reset dis-
play. When conducting the ISW successively after that, press [Trouble reset]. And then, after check-
ing to see if "OK" is displayed, press the key that sets the number of sheets in the order shown below
and start the service mode.
Stop → 0 → 0 → Stop → 0 → 1
Note
• When the ISW other than for the MFP controller is completed, no reboot is made auto-
matically. In cases like this, when conducting the ISW for another board successively,
press [OK] on the screen showing a message "ISW completed," and select again a
board type that conducts the rewrite on the board type selection screen.
14 Check the firmware version in the service mode to see if the rewriting is completed successfully.
1 115
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
The ISWTrns displays messages when an error is shown or the operation is completed. The table below shows
the contents of the message and the status of the ISWTrns.
116
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
The following shows the error displays.
D. ISWTrms troubleshooting
When an error occurs while in the execution of the ISWTrns program.
1 117
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
3 "NG" is displayed while The transferred firmware is damaged. Copy the firmware and check it again.
in the file checksum. When "NG" still recurs, contact the
supplier of the firmware.
4 "??" is displayed while When the firmware was copied to the Copy the checksum file to the same
in the file checksum. PC, the copying of the checksum file firmware as the one for the firmware
(*.sum) was forgotten. at the same time. (If you use the "Data
Copy" function, a copy is made auto-
matically.)
5 An error "Cannot The file is being used by anther pro- Exit another program. The error still
The transfer of the file failed.
118
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
5.3.1 Outline
• [Internet ISW] is the system which gives the instruction for updating the Firmware with the control panel of
the Copier, so the Copier will automatically receive the Firmware from the Program Server over a network
for updating. With the Internet ISW, the Firmware can be updated when the operator is at the User's with-
out Firmware data.
The "Internet ISW" will not operate under the following conditions.
• Main power switch(SW1) is set to OFF.
• Sub-power switch(SW2) is set to OFF.
• When the following setting is set to "ON":
[Administrator Setting] →[Security Setting] →[Enhanced Security Mode]
• The Copier has the job currently performing.
• In case of not attaching Option Harddisk(HD-505).
• When HDD Encryption is set.
• When HDD Lock password is set.
50gaf2e001ca
Note
• Settings such as Server setting, etc. will be available by selecting "ON" on this setting.
• When the following setting is set to "ON", "ON" cannot be selected on this setting.
[Administrator Setting] →[Security Setting] →[Enhanced Security Mode]
1 119
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
B. Protocol Setting
bizhub 500/420/360
• It performs the setting concerning the Protocol (ftp or http) for connecting to the Internet ISW.
• When connecting to the Program Server using a proxy server, perform the setting for a Proxy Server.
1. Select the [Server Address], and set the Proxy Server Address by IP addressing scheme or
FQDN scheme.
2. Select [Port Number], and set the Port Number for the Proxy Server from 1 through 65535.
*PASV Mode:
This mode is for transferring the file with FTP
under the condition where communication is
restricted such as inside the Firewall. Since
with PASV mode, the client with restriction
sets the Port Number, data transmission port
can be secured to enable the file transmis-
sion.
5 Connection Time-Out -
• Select [Connection Time-Out], and set the
time for the Connection Time Out between
30 and 300 seconds.
120 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
• To make the access setting for the Program Server which stores the Firmware data.
1. Select [Internet ISW] which is available from [Service Mode] → [System 2].
2. Touch [Forwarding Access Setting].
50gaf2e002ca
3. Select [User ID], and enter the user ID which is necessary for connecting to the Program Server on the on-
screen keyboard, and touch [END].
4. Select [Password], and enter the Password which is necessary for connecting to the Program Server on the
on-screen keyboard, and touch [END].
5. Select [URL], and enter the directory which stores the Program Server Address and the Firmware on the on-
screen keyboard by URL method, and touch [END].
Note
• Enter the URL which matches to the Protocol to be used.
When connecting to http http://(host name or IP address)/directory name
or https://(host name or IP address)/directory name
When connecting to ftp ftp://(host name or IP address)/directory name
6. Select [File Name], and enter the file name of the Firmware data to be downloaded on the on-screen key-
board, and touch [END].
7. Touch [END] to finish setting.
1 121
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
Note
• When performing the Internet ISW, ask the administrator for permission beforehand.
• Do not turn OFF Main power switch(SW1) and Sub-power switch(SW2) while downloading.
50gaf2e003ca
50gaf2e004ca
4. The Copier will automatically start running, and it starts accessing the server.
50gaf2e005ca
122 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
1. The message to indicate the status will be displayed on the screen while connecting or transferring data.
C. Completed or failed
(1) Firmware updated normally
1. When the Firmware is normally updated, restart the Copier in auto or manual mode to display the outcome,
and touch [OK] to return to the Main screen.
Note
• When turning the main power switch (SW1) ON for the first time after the Firmware is updated,
data may sometimes be internally updated.
In that case, the following message will be displayed. Never turn SW1 OFF until either the Serial
number input screen or the trouble code screen is displayed.
50gaf2e006ca
Note
• For error codes, refer to "5.3.5 Error Code List for the Internet ISW".
1 123
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
1. Once Firmware updating has started, the ROM in the Copier will be deleted.
When it failed right after updating has started, restart the Copier, and shift to the standby screen to retry
downloading.
2. When updating on the control panel, touch [settings] on the standby screen, and check the Network settings
again.
Touch [Download], and restart the Internet ISW.
Note
• Return to the standby screen without fail after turning the Main power OFF/ON if the Firmware is
not updated.
124 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
• When a trouble occurred while conducting the Internet ISW and it was not normally connected, the mes-
sage on the status and the error code will be displayed on the control panel.
When updating with CS Remote Care, the error code will be sent to the CS Remote Care center.
<Sample Display>
50gaf2e007ca
1 125
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
Control panel
0x00111001 Error concerning the network • Check the network environment of the
• It cannot be connected to the User.
server. • Check to see if the FTP server operates
0x00111100 Error concerning the network normally.
• Communication Timeout.
0x00111101 Error concerning the network • Check the network environment of the
• Disconnection occurred User.
0x00111110 Error concerning the network • Check to see if the FTP server operates
• The network is not connected. normally.
0x00110010 Error concerning the network
• Others
0x00001### FTP error • Check to see if FTP server normally
• Reply code when it failed to be operates.
connected • Check the IP address, User's name,
etc.
0x00002### FTP error • Check to see if FTP server operates
• Error reply code for the User normally.
command or Pass command
0x00003### FTP error
• Error reply code for CWD com-
mand
0x00004### FTP error • Check to see if FTP server operates
• Error reply code for the TYPE normally.
command
0x00005### FTP error
• Error reply code for the PORT
command
0x00006### FTP error • Check to see if FTP server operates
• Error reply code for the PASV normally.
command • Set the PASV mode to "Invalid", and try
it again.
0x00007### FTP error • Check to see if FTP server operates
• Error rely code for the RETR normally.
command • Wait for about 30 minutes and try it
again.
0x10000100 • It cannot be accepted because • Wait for the current job to be com-
of the job currently being exe- pleted and try it again.
cuted.
• ISW being executed by other
method.
0x10000101 • It cannot be accepted because • Turn sub-power ON and try it again.
the sub-power is OFF.
0x10000102 • The Internet ISW is already • Wait for the current Internet ISW to be
being executed. completed.
126 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
Control panel
0x10000103 • It failed to prohibit the job. (It • Check if the following setting is set to
failed to lock the operation.) "Valid".
→ It failed to lock the job [Service Mode] → [System 2] → [Inter-
because the operation is already net ISW] → [Internet ISW setting]
locked with PSWC, etc. • If the above process does not solve the
0x10000104 • There is no space for F/W data problem, inform the corresponding
to be downloaded. error code to the KONICA MINOLTA.
0x10000106 • Check sum error
0x10000107 File access error • Check to see if the downloaded F/W is
• The file downloaded has an of the correct type.
error.
• The header of the file which has
been read has an error.
• The size of the file to be down-
loaded is too large.
• When it is identified to be the
different type of F/W.
0x10000108 • The area F/W is stored is • Wait until ISW is automatically exe-
destroyed, and another ISW is cuted on the main body side.
necessary.
0x20000000 The temporary error when running
the subset
• When starting the Internet ISW
in a normal program, the
rebooting will start and the Inter-
net ISW will be executed with
the subset program.
During the process by the sub-
set program, it has to be in the
"Failed" status unless the Inter-
net ISW is successfully con-
ducted. This code is used
temporarily to make it in error
status.
Note
• If the above process does not solve the problem, inform the corresponding errorcode to the KON-
ICA MINOLTA.
1 127
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
• By using this setting, the Firmware stored in the Server can be downloaded over internet for upgrading.
Functions • To set whether or not to enable each setting for Internet ISW.
Use • To use when upgrading the Firmware by Internet ISW.
• Each setting such as Server setting will be valid by setting this to "ON".
Note
• When the following setting is set to "ON", this setting will automatically be
set to "OFF" and cannot be changed.
[Administrator Setting] →[Security Setting] →[Enhanced Security Mode]
Setting/ • The default setting is "OFF".
Procedure ON "OFF"
Functions • To set whether or not to enable downloading using the HTTP Protocol.
Use • To use when accessing the Server using the HTTP Protocol.
• Setting on the Proxy Server will be valid when this setting is "ON".
Setting/ • The default setting is "OFF".
Procedure ON "OFF"
B. Connect Proxy
Functions • To set whether or not to connect via Proxy Server when accessing the Server.
Use • To use when accessing the Server via Proxy Server.
Setting/ • The default setting is "OFF".
Procedure ON "OFF"
C. Proxy Server
Functions • To set the Address and the Port Number for the Proxy Server.
Use • To use when accessing the Server via Proxy Server.
Setting/ <Server Address>
Procedure • Enter the IP Address using the Version 4 method or FQDN method.
<Port Number>
• Enter the value between 1 and 65535 using the 10-key pad.
128 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
D. Proxy Authentication
bizhub 500/420/360
Functions • To set the Login name or Password when Authentication is necessary for accessing
the Proxy Server.
Use • To use when Authentication is necessary for accessing the Proxy Server.
Setting/ <Authentication>
Procedure • The default setting is "OFF".
ON "OFF"
<Log-in Name>
• Enter the Login name (up to 32 one-byte characters) on the on-screen keyboard.
<Password>
• Enter the Password (up to 32 one-byte characters) on the on-screen keyboard.
E. Connection Time-Out
Functions • To set the time for the Timeout for accessing the Server.
Use • To use when changing the time for the Timeout for accessing the Server.
Setting/ • The default setting is "60 sec".
Procedure 30 to 300 sec
B. Connect Proxy
Functions • To set whether or not to access the Server via Proxy Server.
Use • To use when accessing the Server via Proxy Server.
Setting/ • The default setting is "OFF".
Procedure ON "OFF"
1 129
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
C. Proxy Server
bizhub 500/420/360
Functions • To set the Address and the Port No. of the Proxy Server.
Use • To use when accessing the Server via Proxy Server.
Setting/ <Server Address>
Procedure • Enter the IP Address using the Version 4 method or FQDN method.
<Port Number>
• Enter the value between 1 and 65535 using the 10-key pad.
D. Connection Setting
Functions • To set the Port No. and the time for Timeout when accessing the FTP Server, and
also to set whether or not to enable PASV Mode.
Use • To use when accessing the FTP Server.
• To use when connecting by the PASV (passive) Mode (FTP Server side will inform the
connection port before connecting).
Setting/ <Port Number>
Procedure • Enter the value between 1 and 65535 using the 10-key pad.
<PASV Mode>
• The default setting is "OFF".
ON "OFF"
130 1
Field Service Ver.2.0 Jan. 2007 5. FIRMWARE VERSION UP
bizhub 500/420/360
A. User ID
Functions • To register the User ID for accessing the Program Server where Firmware is to be
Use stored.
Setting/ 1. Select [User ID].
Procedure 2. Enter the User ID (up to 64 one-byte characters) on the on-screen keyboard.
B. Password
Functions • To register the Password for accessing the Program Server where Firmware is to be
Use stored.
Setting/ 1. Select [Password].
Procedure 2. Enter the Password (up to 64 characters) on the on-screen keyboard.
C. URL
Functions • To register the Address and Directory of the Program Server where the Firmware is to
Use be stored in URL.
Setting/ 1. Select [URL].
Procedure 2. Enter the URL (up to 256 one-byte characters) on the on-screen keyboard.
Note
• Enter the URL which format suits the Protocol to be used.
When connecting to http http:// (Host name or IP Address)/ Directory name
or https:// (Host name or IP Address)/Directory name
When connecting to ftp ftp:// (Host name or IP Address) / Directory name
D. FileName
1 131
5. FIRMWARE VERSION UP Field Service Ver.2.0 Jan. 2007
5.4.5 Download
bizhub 500/420/360
Functions • Access the Program Server according to the Internet ISW setting, and download the
Firmware.
Use • To use when updating the Firmware via network.
Setting/ 1. Select [Download].
Procedure 2. Touch [ISW Start] to start downloading the Firmware.
3. The message to show the status will be displayed on the screen while connecting
and transferring data.
Note
• When it failed to connect to the Program Server, or failed to download, the
error code and the message will be displayed. Check the cause of the error
by the error code, and follow the message for resetting.
Refer to "5.3.5 Error Code List for the Internet ISW" for the error codes. (See
P.125)
4. When the Firmware is normally upgraded, the Copier will automatically be restarted
to complete the Internet ISW.
132 1
Field Service Ver.2.0 Jan. 2007 6. OTHERS
6. OTHERS
bizhub 500/420/360
6.1 Items not allowed to be disassembled and adjusted
6.1.1 Scanner section
A. CCD unit
(1) Parts not allowed to be removed
• 7 screws that are used to assemble the CCD unit.
• 4 attaching screws of the lens reference plate assy
[3] [1]
[5]
[2]
[2]
133
6. OTHERS Field Service Ver.2.0 Jan. 2007
134
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
A. Write section cover
(1) Parts not allowed to be removed
• 4 attaching screws of the write section cover
[1]
[2]
50gaf2c138na
135
6. OTHERS Field Service Ver.2.0 Jan. 2007
[2]
[1]
[1] [1]
50gaf2c139na
136
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
(1) Parts not allowed to be removed
• 2 attaching screws of the developer restriction blade
• 1 fixing screw of the magnet adjustment plate
• Ds adjustment screws
Developing unit at 2 places (inside the cover)
[6]
[4] [5]
[3]
137
6. OTHERS Field Service Ver.2.0 Jan. 2007
[1]
50gaf2c188na
138
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
Note
• This list shows the explanation of the disassembly and reassembly of the parts which are consid-
ered necessary to replace (other than periodically replaced parts). However, these parts except for
the covers are not required to be disassembled while in normal service operations.
• For the method of replacing the periodically replaced parts, see "3.5 Maintenance procedure of
the external section" to "3.15 Maintenance procedure of the fusing section".
139
6. OTHERS Field Service Ver.2.0 Jan. 2007
Caution
• When disassembling or assembling the parts, be sure the power cord has been unplugged from
the power outlet.
[2]
[2] [1] 50gaf2c050na
140
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
[2]
rear cover /2 [2].
5. Reinstall the above parts following the removal
steps in reverse.
[1] 50gaf2c051na
Note
• The screw [1] is attached with the washer [2].
Be careful that it does not get lost.
[1][2]
[4] [3] 50gaf2c052na
141
6. OTHERS Field Service Ver.2.0 Jan. 2007
A. Procedure
1. Open the bypass tray.
(See P.143)
2. Pull the ADU release lever [1] to open ADU [2].
[2]
[1] 50gaf2c053na
[1] [2] 3. Remove the 2 screws [1] and then remove the
right cover /Up [2].
4. Reinstall the above parts following the removal
steps in reverse.
50gaf2c054na
142
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
A. Procedure
1. Open the bypass tray [1].
2. Remove the 2 screws [2] and then remove the
right cover /Lw [3].
3. Reinstall the above parts following the removal
steps in reverse.
[1]
[3]
[2] 50gaf2c055na
[3]
[2] 50gaf2c056na
143
6. OTHERS Field Service Ver.2.0 Jan. 2007
A. Procedure
1. Open the front door [1].
2. Remove the screw [2] and then remove the sup-
port plate [3] and the front door at the same time.
Note
[5]
• When installing the front door, be sure first to
fit the installation hole [4] to the shaft [5].
[4]
3. Reinstall the above parts following the removal
steps in reverse.
[1]
[2]
[3]
50gaf2c057na
144
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
A. Procedure
1. Remove the 4 screws [1] and then remove the
[1]
upper cover /Rt [2].
[2] 50gaf2c058na
145
6. OTHERS Field Service Ver.2.0 Jan. 2007
Note
• When removing the original glass, be careful
not to stain the position to which the shading
correction plate [6] is attached.
[2]
[3]
[4]
50gaf2c060na
Note
[1] [3]
• When installing the original glass [1], be sure
to fix first the glass attaching plate /Lw [2]
while pressing it against the original glass
and then fix the glass holding plate [3] while
also pressing it against the original glass.
[2] 50gaf2c061na
146
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
A. Procedure
1. Remove the original glass.
[4] [5]
(See P.145)
2. Loosen the screw [1].
3. Remove the 2 screws [2] and then remove the
upper cover /Fr [3].
4. Remove the connector [4].
5. Remove the 4 screws [5] and then remove the
upper cover /Lt [6].
6. Reinstall the above parts following the removal
steps in reverse.
[6]
[1] 50gaf2c063na
147
6. OTHERS Field Service Ver.2.0 Jan. 2007
A. Procedure
1. Open the front door [1].
[1] 2. Pull out the tray 1 [2].
3. Remove the screw [3] and then remove the front
cover [4].
4. Reinstall the above parts following the removal
steps in reverse.
[4] [2]
[3]
50gaf2c160na
148
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
A. Procedure
1. Remove the 4 screw caps [1] and then remove
the 4 screws [2].
2. Remove the connector [4] of the operation board
[1]
(OB) [3] and then remove the operation panel [5].
Note
• When installing the operation panel, be sure
to install the connector [4] without fail.
[2]
[5]
[3]
[4]
50gaf2c064na
149
6. OTHERS Field Service Ver.2.0 Jan. 2007
A. Procedure
1. Remove the original glass.
[2] [1]
(See P.145)
2. Remove the 2 screws [1] and the remove the lens
light blocking cover assy [2].
3. Remove the connector [3].
4. Remove the 9 screws [4] and then remove the
lens light blocking cover [5].
5. Remove the 3 screws [6] and then remove the rib-
bon cable cover [7].
Note
• Be careful not to damage the scanner wire.
150
Field Service Ver.2.0 Jan. 2007 6. OTHERS
Note
bizhub 500/420/360
• When removing the ribbon cable [1], be sure
to bring down the lock lever [3] of the connec-
tor [2] in the arrow-marked direction to
release the lock and pull out the ribbon cable.
151
6. OTHERS Field Service Ver.2.0 Jan. 2007
Note
• After installing the CCD unit, be sure to con-
duct the image adjustment in the service
mode. (See P.185, P.186, P.187, P.188, P.189,
P.190)
152
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
Note
• Be careful not to touch the lamp section of the exposure lamp (L1) with bare hands.
A. Procedure
1. Remove the original glass. At this time, remove
[3] [2] [1]
also the glass attaching plate /Lw.
(See P.145)
2. Remove the connector [1].
3. Remove the harness clamp [2].
4. Remove the 2 screws [3] and slide the exposure
lamp (L1) [4] for removal.
5. Reinstall the above parts following the removal
steps in reverse.
[4]
[3]
50gaf2c073na
153
6. OTHERS Field Service Ver.2.0 Jan. 2007
Note
• When installing the exposure unit, be sure to use the optics unit positioning jig.
• When installing the exposure unit, be sure to conduct the image adjustment in the service mode.
(See P.185, P.186, P.187, P.188, P.189, P.190)
154
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
frame.
8. Remove the connector [3].
9. Remove the screws [4] and [5] and then remove
the exposure unit from the exposure unit mount-
ing plates /Fr [6] and /Rr [7].
10. Slide the exposure unit [1] for removal.
[1] [2]
[4]
[6]
50gaf2c074na
155
6. OTHERS Field Service Ver.2.0 Jan. 2007
Note
• Be sure to insert the optics unit positioning jig
[8]
from the front side and pass it through the V-
mirror unit.
[6]
3. Insert the optics unit positioning jig [5] into the
exposure unit positioning hole [4].
4. Hit the exposure unit [6] against the optics unit
positioning jig [5].
5. Install the exposure unit to the exposure unit
mounting plates /Fr [7] and /Rr [8] with the screws
[9] and [10].
6. Pull off the 2 optics unit positioning jigs.
7. For the parts to be installed in the succeeding
steps, be sure install them following the removal
steps in reverse.
[9]
[7]
50gaf2c075na
156
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
Note
• Be sure to wind the scanner wire around the pulley closely with no scanner wire overlapping each
other.
• When restretching or replacing the scanner wire, be sure to use the optics unit positioning jig.
• When restretching or replacing the scanner wire, be sure to conduct the image adjustment in the
service mode. (See P.185, P.186, P.187, P.188, P.189, P.190)
A. Procedure
1. Remove the original glass. At this time, remove
[1]
also the glass attaching plate /Lw.
(See P.145)
2. Remove the upper covers /Fr and /Lt.
(See P.147)
3. Remove the upper cover /Rr.
(See P.147)
4. Remove the operation panel.
(See P.149)
5. Remove the operation panel unit /Lw assy.
(See P.154)
6. Move the V-mirror unit [1] to the vicinity of the V-
mirror positioning hole [2].
7. Insert the optics unit positioning jig [3] into the V-
[2] [3] mirror positioning hole and fix the V-mirror unit.
50gaf2c076na
Note
• Be sure to insert the optics unit positioning jig
[3] from the operation panel side and pass it
through the V-mirror unit.
157
6. OTHERS Field Service Ver.2.0 Jan. 2007
[8] [7] [6] [1] drive pulley on the side so that the drive pulley [1]
can rotate freely against the pulley shaft [2].
9. Drop the metal ball [5] provided at the intermedi-
ate section of the scanner wire [4] into the drive
[3] pulley installation hole and, with this as a starting
point, wind the wire 6 turns [6] outwards and 5
[4]
[11] turns [7] inwards.
[5] [9]
Note
[2] • The scanner wires are color-coded. Be sure
to use the one painted black on the front side
[12] with the one with no paint on the rear side.
• For each scanner wire that is wound around
the pulley, be sure to use on the outside the
one at the end of which the metal ball [8] is
[12]
provided and on the inside the one at the end
of which the screw thread [9] is provided.
• For each scanner wire, be sure to pull out the
[1] [6] [7] [8]
one that is wound on the outside in the paper
[10]
feed direction [10] from the upper side of the
drive pulley and the one wound on the inside
in the paper exit direction [11] from the upper
[3]
side of the drive pulley.
[4]
10. After completion of the winding of the scanner
[9] [5] wire, be sure to fix it with the tape [12] so that it
does not come off.
50gaf2c077na
11. Pass the scanner wire [2] provided with the metal
[1] ball [1] through the pulley [4] on the paper exit side
[3] [4] [8] after passing through under the V-mirror unit [3],
[6] [2] and pass further through the pulley [5] inside the
V-mirror unit. And then hook it to the notch [6] of
the frame.
12. Pass the scanner wire provided with the screw
[5]
[2] thread through the pulley [7] on the paper feed
side. And then pass it from above through the pul-
ley [8] on the outside of the V-mirror unit and fur-
[7]
ther through under the V-mirror unit and, with the
[4] nut [9] and the washer [10], fix it at the tension of
1.3 kg to 1.7 kg.
[5]
[10] [9]
[8] 50gaf2c078na
158
Field Service Ver.2.0 Jan. 2007 6. OTHERS
Note
bizhub 500/420/360
• When fixing the screw thread side of the
scanner wire, be sure fix it with a tension of
1.3 to 1.7 kg applied by a spring balance in the
arrow-marked direction [1].
• When fixing the scanner wire, be sure to
check to see if the V-mirror unit has been
fixed with the optics unit positioning jig.
• Be sure to tighten up the set screw of the
[1]
drive pulley that has been loosened.
50gaf2c079na
• Be sure to peel off the tape that has been
used for fixing.
Note
• Be sure to slide the exposure unit and check
to see if it operates smoothly.
Note
• Be sure to remove the toner bottle in advance.
A. Procedure
1. Remove the original glass.
[1]
(See P.145)
2. Remove the upper covers /Fr and /Lt.
(See P.147)
3. Remove the upper cover /Rr.
(See P.147)
4. Remove the right cover /Up.
(See P.142)
5. Remove the rear cover /1.
(See P.140)
6. Remove the 9 screws [1] and then remove the
system unit cover [2].
[1] [2]
50gaf2c080na
159
6. OTHERS Field Service Ver.2.0 Jan. 2007
[1]
bon cable cover [2].
8. Remove the ribbon cable [3].
9. Remove the 7 connectors [4].
10. Remove the 11 screws [5] and then remove the
overall control board mounting box [6].
160
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
12. Remove the 3 screws [2] and then remove the
ozone filter mounting assy [3].
[2] [3]
[1]
50gaf2c082na
[2]
[3]
[1]
[4] 50gaf2c083na
161
6. OTHERS Field Service Ver.2.0 Jan. 2007
[2] [1]
17. Remove the 5 screws [2] and then remove the
toner supply unit [3].
18. Reinstall the above parts following the removal
steps in reverse.
[3] [2]
[2]
50gaf2c084na
162
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
Note
• The trays 1 and 2 are of the same form and of the same mechanism. The procedure given here
shows mainly the operations employed for the tray 1.
• When there remains paper in the tray, be sure to remove it thoroughly before starting operations.
A. Procedure
1. Pull out the tray 1 [1].
2. Remove the screw [2] and then remove the stop-
per [3].
[6]
Note
• When installing the stopper, be sure to set the
positioning hole [4] to the projection [5].
Note
• When installing the tray 1, be sure to check to
see if the tray can be pulled out and pushed in
smoothly.
• When installing the tray 1, be sure to check to
see if the tray is not thoroughly pulled out.
[1]
[4] [5]
[3]
[2]
50gaf2c141na
163
6. OTHERS Field Service Ver.2.0 Jan. 2007
[1] Cover [2] Mounting [3] Key [4] Counter [5] Screws [6] Screws [7] Screws
plate counter socket for the for the for the
cover counter mounting
socket plate
Key counter kit 4* z z z z z z z
Key counter z z z z
mounting kit*
Key counter z
* In the kit, parts (such as a mounting plate, mylar, wire saddle and screws) that are not used for 500/420/
360 are included.
164 1
Field Service Ver.2.0 Jan. 2007 6. OTHERS
bizhub 500/420/360
1. Remove the upper cover /Lt.
(See P.147)
2. Remove the split cover [1] of the upper cover /Lt.
3. Put the harness [2] for the key counter through the
upper cover /Lt.
[1] 4. Install the upper cover /Lt.
[2]
50gaf2c184na
[4]
[3]
50gaf2c185na
[5] [6]
50gaf2c186na
[8]
[7]
50gaf2c187na
165
6. OTHERS Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Blank page
166
Field Service Ver.2.0 Jan. 2007 7. HOW TO USE THE ADJUSTMENT/SETTING SECTION
ADJUSTMENT/SETTING
bizhub 500/420/360
7. HOW TO USE THE ADJUSTMENT/SETTING SECTION
7.1 Composition
This part "ADJUSTMENT/SETTING" describes items to be adjusted and the method of adjustment that is
required by this machine, it also gives detailed explanations.
167
8. UTILITY MENU Field Service Ver.2.0 Jan. 2007
8. UTILITY MENU
bizhub 500/420/360
UTILITY MENU
[1] One-Touch [1] Scan [1] Address [1] E-Mail
Registration Book [2] FTP
[3] SMB
[4] User Box
[2] Group
[3] Program
[4] Subject/Text [1] Subject
(for E-mail) [2] Text
[2] Fax [1] Address [1] Abbr. Dial
Book [2] E-Mail
[3] User Box
[2] Group
[3] Program
[4] Subject/Text [1] Subject
(for E-mail) [2] Text
[3] User Box [1] Public/Personal User Box (HDD installed) /Confidential RX User Box
(HDD not installed)
[2] Bulletin Board User Box
[3] Relay User Box
[2] User Setting [1] System Set- [1] Language Selection
ting [2] Measurement Unit Setting
[3] Paper Tray [1] Paper Type
Setting [2] Auto Tray Select Setting
[3] Auto Tray Switch ON/OFF
[4] No Matching Paper in Tray Setting
[5] Print Lists
[5] Power Save [1] Low Power Mode Setting
Setting [2] Sleep Mode Setting
[6] Output Set- [1] Print/Fax Output Setting
ting
[7] Original Image Density
[2] Display Set- [1] Sub Screen Display ON/OFF
ting [2] Copier Setting
[3] Scan Basic Screen Default Setting
[4] Fax Basic Screen Default Setting
[5] Copy Screen
168 1
Field Service Ver.2.0 Jan. 2007 8. UTILITY MENU
UTILITY MENU
bizhub 500/420/360
[2] User Setting [2] Display Set- [6] Fax Active Screen
ting [7] Copier Basic Screen Setting
[8] Job List Default
[3] Initial Setting
[4] Copier Setting
[5] Scanner Setting
[6] Printer Set- [1] Basic Setting
ting [2] Paper Setting
[3] PCL Setting [1] Typeface
[2] Symbol Set
[3] Font Size
[4] Line/Page
[5] CR/LF Mapping
[4] PS Setting
[5] Print Report
[3] Administrator [1] System Set- [1] Power Save Setting
Setting ting [2] Output Set- [1] Print/Fax Output Setting
ting [2] Output Tray Setting
[3] Date/Time Setting
[4] Daylight Saving Time Setting
[5] Weekly [1] Weekly Timer ON/OFF Setting
Timer Setting [2] Time Setting
[3] Date Setting
[4] Select Time for Power Save
[5] Password for Non-Business Hours
[6] Restrict User [1] Restrict Access to Saved Program Jobs
Access [2] Delete Saved Program Jobs
[3] Restrict Access to Job Settings
[4] Restrict Operation Settings
[7] Expert [1] Original Image Density
Adjustment [2] Erase Adjustment
[3] Finisher [1] Center Staple Position
Adjustment [2] Half-Fold Position
[3] Punch Horizontal Position
[4] Punch Resist Loop Size
[8] List/Counter [1] Management List
[2] Paper Size/Type Counter
[9] Reset Set- [1] System Auto Reset
ting [2] Auto Reset
[3] Job Reset
[4] System Auto Reset for Proof copy
1 169
8. UTILITY MENU Field Service Ver.2.0 Jan. 2007
UTILITY MENU
bizhub 500/420/360
[3] Administrator [1] System Set- [0] User Box [1] Delete unused User Box
Setting ting Setting [2] Delete Secure Print Documents
[3] Auto Delete Secure Document
[2] Administra- [1] Administrator Registration
tor/Machine [2] Input Machine Address
Setting
[3] One-Touch [1] Scan [1] Address [1] E-Mail
Registration Book [2] FTP
[3] SMB
[4] User Box
[2] Group
[3] Program
[4] Subject/Text [1] Subject
(for E-mail) [2] Text
[2] Fax [1] Address [1] Abbr. Dial
Book [2] E-Mail
[3] User Box
[2] Group
[3] Program
[4] Subject/Text [1] Subject
(for E-mail) [2] Text
[3] User Box [1] Public/Personal Use Box
[2] Bulletin Board User Box
[3] Relay User Box
[4] Annotation User Box
[4] One-Touch [1] Address Book List
Registration List [2] Group List
[3] Program List
[4] E-Mail Subject/Text List
[4] User [1] General Settings
Authentication/ [2] User Authentication Setting
Account Track [3] Account Track Setting
[4] Print without Authentication
[5] Network [1] Network Setting
Setting [2] TCP/IP Setting
[3] Netware Setting
[4] IPP Setting
[5] FTP Setting
[6] SMB Setting
170 1
Field Service Ver.2.0 Jan. 2007 8. UTILITY MENU
UTILITY MENU
bizhub 500/420/360
[3] Administrator [5] Network [7] AppleTalk Setting
Setting Setting [8] LDAP Set- [1] Enabling LDAP
ting [2] Setting Up LDAP
[3] Default LDAP Server Setting
[9] E-Mail Set- [1] E-Mail TX (SMTP)
ting [2] E-Mail RX (POP)
[0] Detail Set- [1] Device Setting
ting
[2] Time Adjustment Setting
[3] Status Notifi- [1] Notification Address Setting
cation Setting [2] Notification Item Setting
[3] Notification Time Setting
[4] Total Counter Report Setting
[5] PING Confirmation
[6] SLP Setting
[7] LPD Setting
[8] Prefix/Suffix [1] ON/OFF Setting
Setting [2] Prefix/Suffix Setting
[9] Action for Invalid Certificate
[6] Copier Setting
[7] Printer Set- [1] I/F Timeout
ting
[8] Fax Setting [1] Header Information
[2] Header/Footer Position
[3] Telephone Line Setting
[4] TX/RX Setting
[5] Function [1] Function ON/OFF Setting
Setting [2] Dial-In Settings
[3] Memory RX
[4] Closed Network RX
[5] Forward TX Setting
[6] Remote RX
[7] Incomplete TX Hold
[8] PC-Fax RX Setting
[9] TSI User Box Setting
[6] PBX CN Set
[7] Report Settings
[8] Job Settings List
[9] System [1] Open API Setting
Connection [3] Prefix/Suffix Auto Setting
1 171
8. UTILITY MENU Field Service Ver.2.0 Jan. 2007
UTILITY MENU
bizhub 500/420/360
172 1
Field Service Ver.2.0 Jan. 2007 9. LIST OF ADJUSTMENT ITEMS
bizhub 500/420/360
After completion of PM
Page referred to
sure/mirror unit
NVRAM board
to paper feed
Developer
Write unit
CCD unit
Slit glass
Drum
Adjustment/setting items
DF
Machine Printer Print Positioning: Leading Edge P.179 h e {
Area Print Positioning: Side Edge P.180 i f {
Paper Feed Direction Adj. P.181 g d c {
Printer Resist Loop P.183 c {
Bypass Tray Adjustment P.184
Scan Image Position: Leading Edge P.185 d f {
Area Image Position: Side Edge P.186 f g {
Cross Direction Adjustment P.187 e e {
Feed Direction Adjustment P.188 c g d {
Lead Edge Erase Adjustment P.189 j {
Non-Image Area Erase Check P.190 {
Imaging TCR Adjustment P.191 c {
Process Toner Density Adjustment P.192 d c {
Adjustment Laser Diameter Adjustment P.193 e d {
LD1 Offset Adj. P.194 d f e {
LD2 Offset Adj. e g f {
Counter Present Parts Life (Reset) P.201 { {
PM Counter (Reset) P.212 { c { {
PM Counter (Set) {
ADF Paper Feed Direction P.235 d h {
Lead Edge P.236 e i {
Side Edge P.237 g j {
Resist Loop Adj. P.238 c {
Original Size Adj. P.238 h {
Density Adj. P.239 { j k {
Scan Position Adjustment P.240 g f {
Sensor Auto Adjustment P.241 i {
Finisher Center Staple Position P.242 {
Half-Fold Position P.243 {
Punch Horizontal Position P.244 {
Punch Resist Loop P.245 {
Note
• After changing developer, be sure to avoid the printing operation before completion of the TCR
adjustment.
• When replacing the NVRAM board (NRB), be sure to conduct the TCR adjustment after changing
developer.
• When replacing the overall control board (OACB) due to the board being damaged, the NRB that
has been provided on the damaged OACB should be reused on a new OACB in principle. When the
NRB is considered to be damaged, be sure to refer to the support division of the authorized dis-
tributor.
1 173
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
174
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
System 1 Initialization Utility/Administrator Job memory Setting P.199
Setting Data Data
FAX Setting Data
Network Setting Data
Destination Storage Data
CS Remote Care Setting Data
Service Mode Setting Image Process Adj.
(Adj.) Data Data
Machine and ADF
Adjustment Data
All History Data
Communication System Setting P.199
Counter Total Service P.202
Fax Communication Error P.202
Mode P.202
ADF Counter P.204
Service Call P.204
JAM P.206
Present Parts Life P.210
Optional Parts Life P.201
PM P.212
Reuse P.207
Each Size P.209
Pape Jam History P.207
Jam Counter History P.206
Time Series Trouble (SC) P.206
Each Section Trouble (SC) P.204
State Confirmation Sensor Check P.213
Load Check P.221
Memory/HDD Condition P.228
Memory/HDD Adjust- Memory Check P.228
ment HDD R/W Check P.228
HDD Format P.229
Adj. Data Table P.229
ADF Paper Feed Direction P.235
ADF Adjustment:Lead Edge P.236
ADF Adjustment:Side Edge P.237
Resist Loop Adj. P.238
Original Size Adj. P.238
Density Adj. P.239
Scan Position Adjustment P.240
Sensor Auto Adjustment P.241
1 175
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
176 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Enhanced Security CE Password P.300
Administrator Password P.300
Administrator Feature Level P.301
CE Authentication P.301
Billing Setting Counter Setting P.303
Management Function Choice P.304
177
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
This machine is provided with a service mode for various types of adjustments/settings. Data adjusted and/or
set in this mode are stored in the NVRAM board (NRB).
NOTE
• When the CE password is set, a password is required to input to enter the service mode.
5. "Service Mode screen"
The service mode is in the start-up condition.
6. Select an item to set.
The setup screen of each item is displayed.
7. Conduct required operations, and press [END/OK] after completion of the operations.
The setting made at step 6 becomes effective.
8. "Service Mode screen"
Press [Exit] to return to the regular copy screen.
1. While pressing the Utility/Counter key, turn ON the power switch (SW2).
2. Trouble reset screen appears.
3. Press the [Trouble reset].
4. On the Operation panel, press the following keys.
Stop → 0 → 0 → Stop → 0 → 1
5. Service Mode screen appears.
NOTE
• When the CE password has been set, you must enter the password to enter the service mode.
6. Press the key for an item you want to configure.
The setting screen for each item appears.
7. Conduct necessary operations and turn OFF the SW2 after completion of operations.
8. The new settings become effective after restart.
178
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
10.3.1 Print Positioning: Leading Edge (Printer Area)
Adjusts the leading edge timing of the printer image.
This adjustment is used to change the restart timing of paper of the registration roller and adjust the relative
position in the sub scan direction of the image against the paper.
The adjustment can be made for each paper feed (each tray, bypass feed and ADU). And for the bypass feed, it
is possible to make an adjustment for each type of paper (plain paper, thick paper, thin paper, OHP, envelope
and label).
Note
• Be sure to complete the Paper Feed Direction Adj. (Printer Area) before starting this adjustment.
(See P.181)
A. Procedure
NOTE
• When [Batch] is pressed, no test copy is available.
5. "Test Copy screen"
With paper set in the tray selected, press the Start key to output the test pattern (No. 16).
When paper is fed from the bypass feed, set the corresponding type of paper. And then press the Start
key to output the test pattern (No. 16).
6. Press [END].
7. Measure the leading edge timing with a scale.
[1]
Standard value [1]: 20 ± 0.5 mm
50gaf3c001na
179
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Changes the laser write timing and also changes the image position on the drum in the main scan direction to
adjust the mis-centering of the printer image.
For each paper feed (each tray, bypass feed, ADU) and for each paper size (common, small size, large size), the
adjustment can be made.
Note
• Be sure to complete the Cross Direction Adjustment (Scan Area) before making this adjustment.
(See P.181)
A. Procedure
NOTE
• When [Batch] is pressed, no test copy is available.
5. "Test Copy screen"
With paper set in the tray selected, press the Start key to output the test pattern (No. 16).
6. Press [END].
7. Fold the output paper into two in the main scan direction to check it for any discrepancy against the
center line of the print.
Standard value: 0 ± 1.5 mm or less
8. "Print Positioning: Side Edge screen"
Enter a value through the [+]/[–] or numeric keys and press [Setting].
Setting range: – 4.77 (image: to the rear) to + 4.77 (image: to the front) mm
1 step = 0.09 mm
Press [Restore] to return to a value before change.
9. Repeat steps 4 to 8 until it gets within the standard value.
10. Press [END].
180 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
A. Printer
Adjusts the magnification of the printer in the sub scan direction.
This adjustment is used to change uniformly the process speed of the drum and the registration roller and
change the magnification in the sub scan direction of the image on the drum.
The adjustment can be made for each type of paper (normal paper, OHP, thick paper, envelope, label and cus-
tom paper)
Note
• The background of the test pattern to be output is fogging. However, this is not abnormal.
• For thin paper, the setting of normal paper is applicable.
(1) Procedure
[1]
50gaf3c002na
181
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Makes appropriate a paper feed loop amount between the registration roller and the fusing roller to prevent the
transfer slippage at the position about 26 mm from the trailing edge of the transfer paper.
The adjustment can be made for each type of paper (normal paper, OHP, thick paper, envelope, label, custom
paper and user paper).
Note
• This adjustment checks copy image to see if there occurs no transfer jitter. When it is difficult to
check transfer jitter at copy image, be sure to set "1" for DipSW37-2 before adjustment. By this
setting, test pattern will be printed.
• Printer magnification in the paper through direction: The adjustment of the printer should have
been completed. (See P.181)
• For thin paper, the setting of normal paper is applicable.
(1) Procedure
1. "Service Mode screen"
Press [Machine].
2. "Machine Adjust screen"
Press [Printer Area].
3. "Printer Area screen"
Press [Paper Feed Direction Adj.]
4. "Paper Feed Direction Adj. screen"
Press [Fixing Motor Clock].
5. Select an item for the type of paper and press [Test Copy].
6. "Test Copy screen"
• Place the original onto the original glass.
• Set A3 (for metric) or 11 x 17 (for inch) paper that is the type of paper selected. With the print count set at
5, press the Start key.
7. Press [END].
8. Check all of the 5 output sheets ; copy or print, of
paper to see if there occurs no transfer jitter.
Approx.26mm
50gaf3c018na
182 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the paper loop amount at the registration roller section to adjust a paper skew, wrinkles, or a jam at the
registration section.
The adjustment can be made for each paper feed (each tray, bypass feed and ADU) and for each paper size
(large size, intermediate size and small size). And for the bypass feed, it is also possible to make an adjustment
for each type of paper (normal paper, thick paper, thin paper, OHP, envelope, and label).
A. Procedure
NOTE
• When [Batch] is pressed, no test copy is available.
4. "Test Copy screen"
With the paper selected set in the tray, press the Start key to output the test pattern (No. 16).
5. Press [END].
6. Check to see if there occurs no paper skew, wrinkle, or jam at the registration section.
7. "Printer Resist Adjustment screen"
Enter a value through the [+]/[–] or numeric keys and press [Setting].
Setting range:
For bypass feed thick paper (large/small), bypass feed thin paper (large/small), bypass feed OHP (large/
small), bypass feed envelope (large/small), and bypass feed label (large/small):
– 16.64 (smaller) to + 16.51 mm (larger)
1 step = 0.13 mm
1 183
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Conduct this adjustment when the paper size of the bypass tray is not detected correctly.
A. Procedure
184
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the leading edge timing while in the scan in the platen mode.
This adjustment is used to adjust the position at which the read is started in the sub scan direction while the
original is being scanned by the exposure unit.
A. Procedure
185
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the mis-centering of the image in the main scan direction while in the scan in the platen mode.
Note
• Be sure that the adjustment of the Print Position: Side Edge has been completed.
(See P.180)
A. Procedure
186
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the magnification of the image in the main scan direction while in the scan in the platen mode and in the
DF mode.
A. Procedure
50gaf3c003na
187
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the magnification of the image in the sub scan direction while in the scan on the original glass.
This adjustment is used to change the scan speed of the exposure unit.
A. Procedure
[1]
50gaf3c004na
188
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the leading edge erasure amount.
A. Procedure
50gaf3c005na
189
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
When installing this machine, or when moving its installation location, check to see if the non-image area erase
check mechanism of the copy applied setting operates correctly in its installation location, and adjust automati-
cally the sensitivity with which the non-image area is detected.
Pre-arrangements:
• Open DF fully to the limit.
• Avoid putting anything on the original glass.
• Clean the original glass.
A. Procedure
(1) Error 1
Countermeasure - 1
When the non-image area erase function is not used very frequently, or when copy originals that have a dark
background are not copied very frequently in non-image area erase, the copier can be used in the current instal-
lation location. However, when copy originals that have a dark background are frequently copied, install the
copier in a location where less external light gets in (darker) than the present location, and check the non-image
area erase check mode again.
(2) Error 2
Countermeasure - 2
When the non-image area erase function is not used very frequently, the copier can be used in the current instal-
lation location. However, if the non-image area erase function is frequently used, install the copier in a location
where less external light gets in (darker) than the present location, and check the non-image area erase check
mode again. At this time, when there is a bright light source such as a fluorescent light installed directly above
the copier, reconsider the installation location, or take some measures to shield the light source and check the
mode again.
190
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
10.4.1 Charging Main Manual Adj.
Do not conduct this adjustment in the field.
Note
• When changing developer, be sure not to conduct the copy operation before completion of the
TCR adjustment.
A. Procedure
NOTE
• The adjustment is completed in about 180 seconds.
• When there occurs a TCR adjustment error due to the developer agitating operation not com-
pleted successfully, the message "operating ..." disappears and an error code is displayed.
(See P.319)
5. Press [OK].
191
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
This adjustment can be used to increase and/or decrease the toner density of developer.
Use this adjustment when an image fogging occurs due to the increased toner density of developer and you
want to decrease the toner density.
A. Procedure
NOTE
• The set value is a value relative to the present set value. When the set value is set to "0," this
returns the toner density back to the normal level.
4. Press the Start key.
5. While in the adjustment, a message "operating ..." is displayed. And after completion of the adjustment, it
disappears.
NOTE
• The toner density is automatically adjusted according to a value set.
• When an error code is displayed while in the toner density adjustment, be sure to check the
expected defective parts given in the error code list and then conduct again the toner density
adjustment.
(See P.319)
6. Press [OK].
192
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
The MPC value can be corrected by entering a set value to change the image density (dot diameter).
A. Procedure
NOTE
• When an adjustment is made in the denser direction, this increases the dot diameter with the
toner consumption also increased.
4. Press the Start key.
5. While in the adjustment, a message "operating ..." is displayed. And after completion of the adjustment, it
disappears.
6. Press [OK].
193
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Note
• Make sure that the TCR adjustment, the toner density adjustment and the dot diameter adjust-
ment have been completed.
A. Procedure
50gaf3c006na
194
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
10.5 System 1
bizhub 500/420/360
10.5.1 Marketing Area
Sets the marketing area of the main body and the fax.
• Marketing area of the main body:
By setting the marketing area, the definition of the original detection size and the paper size will be changed.
And the selectable languages in "Marketing Area screen" varies according to the marketing area of the firmware.
• Fax Target:
US (America), CA (Canada), JP (Japan), AU (Australia), NZ (New Zealand), EU (Europe), DE (Germany), GB
(England), FR (France), CH (Switzerland), NL (Netherlands), BE (Belgium), AT (Austria), NO (Norway), SE (Swe-
den), FI (Finland), IE (Ireland), DK (Denmark), IT (Italy), ES (Spain), PT (Portuguese), PL (Poland), ZA (South
Africa), TW (Taiwan), SA (Saudi Arabia), CN (China), MY (Malaysia), SG (Singapore), KR (Korea), HK (Hong Kong),
OT (Argentine)
A. Procedure
1 195
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Sets the telephone number and the fax number of the service station that are displayed on the screen when a
service call occurs.
These telephone and fax numbers are also displayed as the service center contact of the basic screen help of
the user screen.
A. Procedure
NOTE
• Pressing the Clear key erases all the figures of the items selected.
Caution
• Be absolutely sure not to change the serial numbers of the main body set when installing them.
Otherwise, a fusing temperature abnormality may result.
A. Procedure
196
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
When each function (device) is in trouble, isolating a trouble allows the limited use of this machine.
A. Procedure
10.5.5 No Sleep
Sets the availability/unavailability of the sleep while in the administrator mode.
A. Procedure
A. Procedure
197
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Sets the detection size of the original size on the original glass and ADF.
A. Procedure
A. Procedure
198
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Sets the start date of the total counter.
A. Procedure
10.5.10 Initialization
Initializes the setting/adjustment data controlled in non-volatile memory to the value set when shipped from the
factory.
Data that can be initialized are as follows.
A. Procedure
199
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
A. Procedure
NOTE
Operating conditions when using JScribe are as follows:
• An optional hard disk and an image controller shall be equipped.
• System memory shall be added (Add-on memory : 128MB).
4. Press [OK].
200 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
10.6 Counter
bizhub 500/420/360
10.6.1 Display of the Counter
Displays the following data held by this machine on the touch panel.
The counter can be also checked by the output list, CSRemoteCare.
• Total Service
• Fax Communication Error
• Mode
• ADF Counter
• Service call
• JAM
• Present parts life
• Optional parts life
• PM
• Reuse
• Each size
• Paper Jam History
• Jam counter history
• Time series trouble (SC)
• Each section trouble (SC)
A. Procedure
NOTE
• For the individual data check screens of "JAM Counter History" and "Each Section Trouble
(SC)," [Clear Counter] is displayed.
Pressing [Clear Counter] displays "Clear Counter Check screen" and pressing [Yes] clears the block data.
Pressing [No] returns to the previous screen with no block data cleared. While in the visit to the user for the
PM execution, clear these data to check the JAM and SC counts that have occurred since the previous
visit.
4. Press [OK].
201
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
B. Total Service
bizhub 500/420/360
Displays the total copy count printed in the service mode and the user mode.
Note
• The maximum count is 99,999,999.
Note
• The maximum count is 999,999.
D. Mode
Displays the use condition for each of the modes used by the copier/scanner/printer/FAX.
Note
• The maximum count is 99,999,999.
202
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
(F1)
6 08 BOX Housing: Copy – Proof Print 1 count for each completion of a job.
7 09 BOX Housing: Copy – BOX Hold
8 0A BOX Housing: Print – Proof Print
9 0B BOX Housing: Print – BOX Hold
10 0C BOX Housing: Print
– Classified Document
11 0D BOX Housing: Scanner – BOX Hold
12 0E BOX Housing: FAX Scanning 1 count for each completion of a job
– BOX Hold
13 0F BOX Housing: FAX RX
– Distribute by F-Code
14 10 BOX Housing: FAX RX – Distribute by TSI
15 11 BOX Housing: FAX RX – BOX Hold 1 count for each completion of a job. F
code and other than TSI.
16 12 Output from Box: Copy Image – Print 1 count for each completion of a job.
Except for the print for checking.
17 13 Output from Box: Copy Image 1 count for each completion of a job.
– E-Mail TX
18 14 Output from Box: Copy Image – FTP TX
19 15 Output from Box: Copy Image – SMB TX
20 16 Output from Box: Print Image 1 count for each completion of a job.
– Print (Except Proof Print) Except for the print for checking.
21 17 Output from Box: Print Image – E-Mail TX 1 count for each completion of a job
22 18 Output from Box: Print Image – FTP TX
23 19 Output from Box: Print Image – SMB TX
24 1A Output from Box: Scan Image – Print
25 1B Output from Box: Scan Image
– E-Mail TX
26 1C Output from Box: Scan Image – FTP TX
27 1D Output from Box: Scan Image – SMB TX
28 1E Output from Box: FAX Scan Image
– Print
29 1F Output from Box: FAX Scan Image
– FAX TX
30 20 Output from Box: FAX Scan Image
– E-Mail/IFAX TX
31 21 Output from Box: FAX RX Image – Print
32 22 Output from Box: FAX RX Image
– FAX TX
33 23 Output from Box: FAX RX Image
– E-Mail/IFAX TX
203
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
E. ADF Counter
bizhub 500/420/360
Note
• The maximum count is 99,999,999.
• 1 count for the single sided copy and 2 counts for the double sided copy.
F. Service Call
Displays troubles that have occurred for each SC.
Note
• The maximum count is 9,999.
• The block trouble count is not available for CSRC.
• When the service mode DipSW3-1 is set to "1" (latched), SC34, 35 and 36 make no count.
204
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
parameter parameter parameter
(E0) (E0) (E0)
052 33 35 01 093 5C B1 11 134 85 B1 64
053 34 35 02 094 5D B1 12 135 86 B1 65
054 35 37 01 095 5E B1 13 136 87 B1 66
055 36 38 01 096 5F B1 14 137 88 B1 67
056 37 38 02 097 60 B1 15 138 89 B1 68
057 38 38 03 098 61 B1 16 139 8A B1 69
058 39 38 04 099 62 B1 17 140 8B B1 70
059 3A 38 05 100 63 B1 18 141 8C B1 71
060 3B 38 06 101 64 B1 19 142 8D B1 72
061 3C 38 07 102 65 B1 20 143 8E B1 73
062 3D 38 08 103 66 B1 22 144 8F B1 74
063 3E 39 01 104 67 B1 23 145 90 B1 75
064 3F 39 02 105 68 B1 25 146 91 B1 76
065 40 39 03 106 69 B1 26 147 92 B1 77
066 41 39 04 107 6A B1 27 148 93 B1 78
067 42 40 01 108 6B B1 28 149 94 B1 80
068 43 41 01 109 6C B1 29 150 95 B1 81
069 44 44 01 110 6D B1 30 151 96 B1 82
070 45 47 01 111 6E B1 31 152 97 B1 83
071 46 50 01 112 6F B1 32 153 98 B1 84
072 47 50 02 113 70 B1 33 154 99 B1 85
073 48 50 03 114 71 B1 34 155 9A B1 86
074 49 50 04 115 72 B1 35 156 9B B1 87
075 4A 53 01 116 73 B1 36 157 9C B1 88
076 4B 53 02 117 74 B1 37 158 9D C1 03
077 4C 53 03 118 75 B1 40 159 9E C1 81
078 4D 54 01 119 76 B1 41 160 9F C1 82
079 4E 54 02 120 77 B1 42 161 A0 C1 83
080 4F 60 01 121 78 B1 43 162 A1 C2 84
081 50 60 02 122 79 B1 44 163 A2 C2 85
082 51 60 03 123 7A B1 45 164 A3 C2 86
083 52 61 01 124 7B B1 46 165 A4 C2 87
084 53 62 01 125 7C B1 50 166 A5 C2 88
085 54 67 01 126 7D B1 51 167 A6 D0 01
086 55 67 02 127 7E B1 52 168 A7 D0 02
087 56 80 01 128 7F B1 53 169 A8 D2 01
088 57 83 01 129 80 B1 54 170 A9 D2 03
089 58 B0 01 130 81 B1 60 171 AA D2 81
090 59 B0 02 131 82 B1 61 172 AB D2 82
091 5A B0 03 132 83 B1 62 173 AC E0 01
092 5B B1 10 133 84 B1 63 174 AD E0 02
205
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Note
• Press the corresponding SC item to display a firmware version.
Note
• The maximum count is 999,999.
• The jam code is a code that is displayed when DipSW10-7 is set at "1."
No. CSRC Jam cord No. CSRC Jam cord No. CSRC Jam cord
parameter Upper Lower parameter Upper Lower parameter Upper Lower
(J0) (J0) (J0)
01 00 10 — 07 06 13 2 13 0C 13 11
02 01 11 — 08 07 13 5 14 0D 14 0
03 02 12 0 09 08 13 6 15 0E 14 1
04 03 12 1 10 09 13 7 16 0F 15 0
05 04 13 0 11 0A 13 8 17 10 15 1
06 05 13 1 12 0B 13 9 18 11 20 1
206
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
No. CSRC Jam cord No. CSRC Jam cord No. CSRC Jam cord
bizhub 500/420/360
parameter Upper Lower parameter Upper Lower parameter Upper Lower
(J0) (J0) (J0)
19 12 20 2 40 27 61 5 61 3C 66 2
20 13 20 3 41 28 61 6 62 3D 66 3
21 14 20 4 42 29 61 7 63 3E 66 4
22 15 20 5 43 2A 61 8 64 3F 66 5
23 16 20 6 44 2B 62 1 65 40 66 6
24 17 20 7 45 2C 62 2 66 41 66 7
25 18 20 8 46 2D 62 3 67 42 66 8
26 19 20 9 47 2E 62 4 68 43 72 16
27 1A 20 10 48 2F 62 5 69 44 72 17
28 1B 30 — 49 30 62 6 70 45 72 18
29 1C 31 — 50 31 62 7 71 46 72 21
30 1D 32 — 51 32 62 8 72 47 72 25
31 1E 33 — 52 33 63 1 73 48 72 43
32 1F 34 — 53 34 63 2 74 49 72 81
33 20 50 1 54 35 63 3 75 4A 72 82
34 21 60 1 55 36 63 4 76 4B 72 84
35 22 60 2 56 37 63 5 77 4C 72 85
36 23 61 1 57 38 63 6 78 4D 72 90
37 24 61 2 58 39 63 7 79 4E 97 1
38 25 61 3 59 3A 63 8 80 4F 97 2
39 26 61 4 60 3B 66 1 81 50 97 3
J. Reuse
Displays the accumulated hours of the parts and the number of occurrences of the job that uses the parts.
Note
• The maximum count is 99,999,999.
207
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
(F5)
5 04 Print operating time (single sided mode) Accumulated hours from start to stop
of the print. 1 count for 1 second (not
including the time period during which
the counter stops due to a jam).
6 05 Print operating time (double sided mode) Accumulated hours from start to stop
of the print. 1 count for 1 second (not
including the time period during which
the counter stops due to a jam).
7 06 Correction operation count Number of counts the image stabiliza-
tion control (the fusing temperature
lower than 50 °C) is executed. 1 count
for each execution.
8 07 APS sensor ON time Accumulated hours during which the
APS sensor turns ON. 1 count for 1
second.
9 08 Platen scan count Counts the number of occasions in
which the scan is made in the platen
mode.
10 09 The number of occurrences of the stop Counts the number of occasions in
due to toner running out. which the system stops due to no
toner.
11 0A Polygon stop operation time
12 0B The number of occurrences of the Main Counts the number of NMI's.
Power OFF
13 0C The number of occurrences of the feed 1 count is made each time the feed
door closed door is closed.
14 0D The number of starting all print jobs
15 0E Tray 1 paper feed count 1 count is made when paper is fed
from the tray 1 each time 1 sheet of
paper is exited.
16 0F Tray 2 paper feed count 1 count is made when paper is fed
from the tray 2 each time 1 sheet of
paper is exited.
17 10 Tray 3 paper feed count 1 count is made when paper is fed
from the tray 3 each time 1 sheet of
paper is exited.
18 11 Tray 4 paper feed count 1 count is made when paper is fed
from the tray 4 each time 1 sheet of
paper is exited.
19 12 The number of prints made by selecting 1 count is made when paper is fed
the bypass paper feed tray from the bypass tray each time 1 sheet
of paper is exited.
20 13 The number of prints made by selecting 1 count is made when paper is fed
the LCT paper feed tray from LCT each time 1 sheet of paper is
exited.
208
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
K. Each Size
bizhub 500/420/360
Displays the number of print of each paper size.
Note
• The maximum count is 99,999,999.
• 1 count each time paper is exited (0 count for a blank sheet and 2 counts for the double sided
print).
209
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
210 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
parameter
(Z1)
25 18 Fusing unit Fusing roller 50GA5303
26 19 Fusing pressure roller 50GA5304
27 1A Fusing cleaner assy 50GA-540
28 1B Heat insulating sleeve /A 26NA5372
29 1C Fusing bearing /Up 26NA5371
30 1D Fusing bearing /Lw 50GA5359
31 1E Fusing sensor assy 50GA-544
32 1F Fuse holder assy 26NA-535
33 20 Fusing claw assy 50GA-533
34 21 Fusing driven roller A assy 4040R706
35 22 Fusing driven roller B assy 4040R707
36 23 Reverse unit Paper exit suction filter 50GA4406
37 24 Write unit Write unit 50GA-650
38 25 LU-201 Pick-up rubber 40LA4009
39 26 Paper feed rubber 26NA4011
40 27 Separation rubber 26NA4012
41 28 DF-607 Pick-up roller 43445003
42 29 Paper feed roller 45823014
43 2A Separation roller 45823047
44 2B PC-202 (tray 3/tray 4) Tray 3 pick-up roller 40303005
45 2C PC-402 (tray 3 only) Tray 3 paper feed roller 40303005
46 2D Tray 3 separation roller 40300151
47 2E Tray 4 pick-up roller 40303005
48 2F Tray 4 paper feed roller 40303005
49 30 Tray 4 separation roller 40300151
50 31 Fusing unit Fusing input gear assy 50GA-546
1 211
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.6.3 PM
bizhub 500/420/360
Note
• The PM cycle setting has been input in advance and be sure not to change this setting normally.
212
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
10.7.1 Sensor Check
This machine is provided with an input/output check function as a self-diagnostic function. For the sensor check
(input check), the state confirmation of each signal can be made.
A. Procedure
B. List of sensors
Multi code
Symbol
ON OFF
Code
Name
213
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Multi code
Symbol
ON OFF
Code
Name
214
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Multi code
Symbol
Code ON OFF
Name
16 10 PS13 Lower limit sensor (PC-402) Lower limit Not at lower limit
Paper feed
home position
2 PS31 APS timing sensor DF close DF open
2 — — — —
3 PS1 Paper full sensor Full Other than full
1 215
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Multi code
Symbol
ON OFF
Code
Name
TH2 mistor /2
216
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Multi code
Symbol
Code ON OFF
Name
217
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Multi code
Symbol
ON OFF
Code
Name
218
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Multi code
Symbol
Code ON OFF
Name
*3 ON/OFF combination of remaining paper sensor /1 (PS154) and /2 (PS151) represents an amount of
paper remained in LU.
219
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
*4 The combination of the ON/OFF of the paper size sensors /BP1 (PS19), /BP2 (PS20), /BP3 (PS21) and
bizhub 500/420/360
*5 The combination of the ON/OFF of the paper size boards and the paper size detection boards (4 in all) is
shown in 4-bit data (0 to 15).
Sensor check display State of each of the 4 sensors on the paper size boards
17-2 (tray 1), 17-3 (tray 2), /1 (PSB /1) and /2 (PSB /2) and the paper size detect
17-4 (tray 3), 17-5 (tray 4) boards /3 (PSDB /3) and /4 (PSDB /4)
1 2 3 4
0 OFF OFF OFF OFF
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
7 ON ON ON OFF
8 OFF OFF OFF ON
9 ON OFF OFF ON
10 OFF ON OFF ON
11 ON ON OFF ON
12 OFF OFF ON ON
13 ON OFF ON ON
14 OFF ON ON ON
15 ON ON ON ON
220
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
This machine is provided with an input/output check function as a self-diagnostic function. For the load check,
the check and adjustment (output check) of the load operation can be made.
A. Procedure
B. List of loads
High voltage/image Classification
Multi code
Symbol
Code
0 0 L1 Exposure lamp
1 0 M4, Toner supply motor, toner solenoid Same as 55-003
SD5 turn ON at the same time
221
10. SERVICE MODE
Paper feed Classification Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Multi code
Symbol
Code
222
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
Paper feed Classification
bizhub 500/420/360
Multi code
Symbol
Code
Name Restrictive conditions
23 3 M124 Paper lift motor /3 (PC-202) The upper limit sensor /3 (PS114)
turns ON, or it is stopped by the stop
button.
4 M125 Paper lift motor /4 (PC-202) The upper limit sensor /4 (PS123)
turns ON, or it is stopped by the stop
button.
5 M151 Paper lift motor (LU) The upper limit sensor (PS152) turns
ON, or it is stopped by the stop but-
ton.
6 M9, Feed motor, pick-up solenoid /BP turn Valid only when the paper empty sen-
SD1 ON at the same time sor/BP (PS18) detects a no paper
condition.
25 1 CL1 Registration clutch
2 CL2 Loop clutch
3 CL3 Vertical conveyance clutch
4 CL151 Feed clutch (LU)
29 0 SD2 Drum claw solenoid ON
31 1 M2, L1 Scanner motor, exposure lamp After home position search, A3
Optical device
223
10. SERVICE MODE
Main body Classification Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Multi code
Symbol
Code
2 EL Erase lamp
52 0 TSL Transfer exposure lamp
53 0 SD4 Web solenoid
55 1 M4 Toner supply motor
2 SD5 Toner solenoid
3 M4, Toner supply motor, toner solenoid
SD5 turn ON at the same time
224
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
Specific function Classification
bizhub 500/420/360
Multi code
Symbol
Code
Name Restrictive conditions
2 — — —
3 M4, After alignment motor /Rr, /Fr opera-
M5 tion, home position search
4 — — —
5 M11 Tray lift motor up Stops when the upper limit sensor
(PS15) turns ON after the tray posi-
tion sensor (PS3) detects the tray 2.
6 M11 Tray lift motor initial operation After the tray goes down, it goes up
when the lower limit sensor (PS14)
turns ON and it stops when PS15
turns ON. It becomes valid after exe-
cuting the load check 70-5.
7 M12 Shutter close/open operation once At the same time, the paper exit roller
release/pressure operation is made
by the paper exit roller release motor
(M6).
8 — — —
9 — — —
10 — — —
225
10. SERVICE MODE
FS-510 Classification Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Multi code
Symbol
Code
ward
2 Reverse motor (LS210) rotating for-
ward
3 Reverse motor (LS125) rotating for-
ward
4 Reverse motor (LS250) rotating back-
ward
5 Reverse motor (LS210) rotating back-
ward
6 Reverse motor (LS125) rotating back-
ward
81 1 CL7 ADU conveyance clutch /Up
2 CL8 ADU conveyance clutch /Lw
3 M9, Feed motor, ADU conveyance clutch
CL7 /Up turn ON at the same time
226
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
ADU/Reverse Classification
bizhub 500/420/360
Multi code
Symbol
Code
Name Restrictive conditions
1 227
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Displays the memory capacity and the hard disc capacity (total/free space).
A. Procedure
A. Procedure
A. Procedure
228
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Formats HDD.
Note
• When formatting HDD, all the data stored in HDD gets lost and becomes unrecoverable.
A. Procedure
Note
• Turning ON SW1 not waiting for 10 seconds or more after turning it OFF may damage HDD. Be
sure to turn ON SW1 10 seconds or more after turning it OFF.
A. Procedure
229
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
230
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
6/28 Magnification in the printer feed direction (printer: OHP (small))
Magnification in the printer feed direction (printer: thick paper (large))
Magnification in the printer feed direction (printer: thick paper (small))
Magnification in the printer feed direction (printer: envelope)
Magnification in the printer feed direction (printer: label (large))
Magnification in the printer feed direction (printer: label (small))
Magnification in the printer feed direction (printer: custom paper)
7/28 Magnification in the printer feed direction (fixing motor clock: normal paper)
Magnification in the printer feed direction (fixing motor clock: OHP (large))
Magnification in the printer feed direction (fixing motor clock: OHP (small))
Magnification in the printer feed direction (fixing motor clock: thick paper (large))
Magnification in the printer feed direction (fixing motor clock: thick paper (small))
Magnification in the printer feed direction (fixing motor clock: envelope)
Magnification in the printer feed direction (fixing motor clock: label (large))
8/28 Magnification in the printer feed direction (fixing motor clock: label (small))
Magnification in the printer feed direction (fixing motor clock: custom paper)
Magnification in the printer feed direction (fixing motor clock: user paper)
Printer registration loop amount (tray 1 (small))
Printer registration loop amount (tray 1 (large))
Printer registration loop amount (tray 2 (small))
Printer registration loop amount (tray 2 (middle1))
9/28 Printer registration loop amount (tray 2 (middle2))
Printer registration loop amount (tray 2 (large))
Printer registration loop amount (tray 3 (small))
Printer registration loop amount (tray 3 (middle))
Printer registration loop amount (tray 3 (large))
Printer registration loop amount (tray 4 (small))
Printer registration loop amount (tray 4 (middle))
10/28 Printer registration loop amount (tray 4 (large))
Printer registration loop amount (option tray)
Printer registration loop amount (LCT)
Printer registration loop amount (bypass (normal (small)))
Printer registration loop amount (bypass (normal (middle)))
Printer registration loop amount (bypass (normal (large)))
Printer registration loop amount (bypass (thick paper: small))
11/28 Printer registration loop amount (bypass (thick paper: large))
Printer registration loop amount (bypass (thin paper: small))
Printer registration loop amount (bypass (thin paper: large))
Printer registration loop amount (bypass (OHP: small))
Printer registration loop amount (bypass (OHP: large))
Printer registration loop amount (bypass (envelope))
Printer registration loop amount (bypass (label: small))
231
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
232
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
18/28 ADF registration loop amount (single sided)
ADF registration loop amount (double sided)
ADF original size (maximum width)
ADF original size (minimum width)
ADF density
ADF scan position
Center staple position (B5S)
19/28 Center staple position (A4S)
Center staple position (B4)
Center staple position (A3)
Center staple position (81/2 x 11S)
Center staple position (11 x 17)
Center staple position (8K)
Center staple position (81/2 x 14)
20/28 Half-fold position (B5S)
Half-fold position (A4S)
Half-fold position (B4)
Half-fold position (A3)
Half-fold position (81/2 x 11S)
Half-fold position (11 x 17)
Half-fold position (8K)
21/28 Half-fold position (81/2 x 14)
Punch horizontal position
Punch registration loop amount (B5S)
Punch registration loop amount (B5)
Punch registration loop amount (A4S)
Punch registration loop amount (A4)
Punch registration loop amount (B4)
22/28 Punch registration loop amount (A3)
Punch registration loop amount (81/2 x 11S)
Punch registration loop amount (81/2 x 11)
Punch registration loop amount (81/2 x 14S)
Punch registration loop amount (11 x 17)
Punch registration loop amount (8K)
Punch registration loop amount (16K)
23/28 Punch registration loop amount (16KS)
Punch registration loop amount (FLS)
Test pattern density
DipSW No.01
DipSW No.02
DipSW No.03
DipSW No.04
233
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
234
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
10.8 ADF
bizhub 500/420/360
10.8.1 Paper Feed Direction
Adjusts the magnification in the sub scan direction while in the DF original scan.
This adjustment adjusts the magnification of the image data in the sub scan direction by changing the scan
speed of DF.
The adjustment is made for each mode (single sided, double sided (front/rear)) and expansion/reduction ratio
(50%, 100%, 200%, 400%).
Note
• Make sure that the adjustment of the magnification in the printer paper feed direction has been
completed.
(See P.181)
A. Procedure
235
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the position at which the image read is started while in the DF original scan.
This adjustment adjusts the leading edge position of the image by changing the image read start timing after the
leading edge of the original passes through the read position.
The adjustment is made for each mode (1-Sided, 2-Sided (Front/Back)).
A. Procedure
236
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the mis-centering of the image in the main scan direction while in the DF original scan.
The adjustment is made for each mode (1-Sided, 2-Sided (Front/Back)).
Note
• Make sure that the adjustment of the printer position: side edge has been completed.
(See P.180)
A. Procedure
237
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the original loop amount (1-Sided or 2-Sided) at the registration roller section of DF to adjust a paper
skew, wrinkles or an original jam at the registration section.
This adjustment adjusts the re-start timing of the DF registration roller.
A. Procedure
A. Procedure
238
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
This adjustment is made when the slit glass is replaced.
The slit glass at the scanner section is coated, and therefore, its transmittance of the exposure lamp is different
when compared to the original glass.
Prearrangements
• Clean the slit glass.
• Check the whole area of the white chart to see if it is not soiled.
A. Procedure
NOTE
• Be sure to set the white chart in the A4 direction.
4. Press the Start key.
When the white chart is scanned and the auto adjustment of density is completed successfully, "OK" is
displayed.
5. When an error message is displayed, turn OFF and ON the power switch (SW2) of the main body and
repeat steps 3 to 4 until it is completed successfully.
6. Press [OK].
239
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the read start position of the exposure unit in the sub scan direction.
A. Procedure
50gaf3c012na
240
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
This adjustment is made when an erroneous detection occurs with the reflective sensor, or after the DF control
board (DFCB) and each of the reflective sensors are replaced. Conducting this adjustment backs up the sensi-
tivity value of each of the reflective sensors to RAM in DFCB.
Prearrangement
• Clean each of the reflective sensors of DF.
Note
• After conducting [Initialization + Auto Adjust], the value of the original size VR (VR1) is reset. Be
sure to conduct [Original Size Adjustment].
A. Procedure
241
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.9 Finisher
bizhub 500/420/360
Note
• Before conducting this adjustment, make sure that the adjustment of the half-fold position has
been completed.
(See P.243)
A. Procedure
4511f3c005na
242
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the folding position while in the stitch-and-fold print by SD-502.
A. Procedure
4511f3c006na
NOTE
• When there occurs a shift shown at step 7, enter a value on the minus (–) side.
9. Repeat steps 3 to 8 until it gets inside the standard value.
10. Press [OK].
243
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Adjusts the position of the punch holes by PU-501 in the sub scan direction.
A. Procedure
4512f3c003na
244
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Adjusts the registration loop amount while in the punch by PU-501.
This adjustment is made when there occurs a tilt with the punch hole, or when a jam occurs frequently in the
punch mode.
A. Procedure
4512f3c004na
NOTE
• When a jam occurs in the punch mode, set a value to the minus (–) side.
• When the line of punch holes is slanted, set a value to the plus (+) side.
8. Repeat steps 3 to 7 until it gets inside the standard value.
9. Press [OK].
245
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.10Firmware Version
bizhub 500/420/360
A. Procedure
246
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
10.11.1 Outlines
• CS Remote Care enables the machine and the computer at CS Remote Care center to exchange data
through telephone/fax line or e-mail in order to control the machine.
• CS Remote Care enables the machine to call the computer at the center when trouble occurs. It also ena-
bles the computer at the center to contact the machine for the necessary data.
• Data which CS Remote Care handles can be divided into the following groups.
a. Data which show the status of use of the machine such as Total count, PM count.
b. Data which show the abnormal situation on the machine such as where and how often errors occur.
c. Data on adjustment
d. Data on setting
Note
• It cannot be set when the following setting is set to “ON”.
[Administrator Setting] → [Security Setting] → [Enhanced Security Mode]
Note
• For resetting up the machine which CS Remote Care has already been set up, clear the RAM for
CS Remote Care before resetting.
For clearing RAM, see "(3) RAM Clear" in "C. Detail Setting" in "10.11.8 Detail on settings".
(See P.257)
• When using the telephone line for connection, use the recommended modem.
(For recommended modem, contact responsible person of KONICA MINOLTA.)
• When using the telephone line for connection, select [CS Remote Care] in [Communication Sys-
tem Setting] screen ([Service Mode] → [System 1] → [Communication System Setting]).
Step Procedure
Using the telephone line Using the Fax line Using E-mail
modem modem *1
0 Register the device ID to the application at CS Remote Care Center.
The initial connection is not available unless the device ID is registered.
1 Connecting the Be sure to remove the Be sure to remove the telephone line modem
modem telephone line modem when e-mail is used.
Turn the power for the when the fax line is
modem OFF. Connect used.
the machine and the
modem with a modem
cable. Connect the
modem and the wall
jack with a modular
cable.
* For connecting the
modular cable, see the
manual for the modem.
1 247
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Step Procedure
bizhub 500/420/360
Using the telephone line Using the Fax line Using E-mail
modem modem *1
2 Clearing the RAM
1. Select [Service Mode] → [CS Remove Care], and touch [Detail Setting].
2. Touch [RAM Clear].
3. Select Set, and touch [OK].
(See P.258)
3 Selecting the CS Selecting the CS Selecting the CS Remote Care function
Remote Care function Remote Care function Select [Service Mode] → [CS Remote Care] →
Select [Service Mode] Select [Service Mode] [System Setting], and touch [E-Mail].
→ [CS Remove Care] → [CS Remove Care]
→ [System Selection], → [System Selection],
and touch [Modem]. and touch [Fax].
4 Inputting the ID Code
1. Select [Service Mode] → [CS Remote Care] → [ID Code], and touch [ID Code].
2. Input the seven digits ID of the service person, and touch [ID Code] again.
(See P.257)
5 Setting the date and time for CS Remote Care
1. Select [Service Mode] → [CS Remote Care], and touch [Detail Setting].
2. Touch [Date & Time Setting].
3. Input the date, time and the time zone using the 10-Key Pad, and touch [Set].
(See P.257)
6 Setting the Center ID
1. Select [Service Mode] → [CS Remote Care], and touch [Detail Setting].
2. Touch [Machine Setting] → [Center ID], and input the Center ID (five digits).
(See P.257)
7 Setting the Device ID
1. Select [Service Mode] → [CS Remote Care], and touch [Detail Setting].
2. Touch [Machine Setting] → [Device ID], and input Device ID (nine digits).
(See P.257)
8 Setting the telephone number of the Center Setting the Respond Timeout
1. Select [Service Mode] → [CS Remote Care], 1. Select [Service Mode] → [CS Remote Care],
and touch [Detail Setting]. and touch [Detail Setting].
2. Touch [Machine Setting] → [Center Tele- 2. Touch [Respond Timeout] and enter the
phone Number]. response timeout using the 10-Key Pad.
3. Input the telephone number of the Center NOTE
using the 10-Keys Pad and [P], [T], [W], [-]. • Under normal conditions, there is no
(See P.257) need to change the default setting.
(See P.257)
9 Inputting the Device telephone number Proceed to Step 10.
1. Select [Service Mode] → [CS Remote Care],
and touch [Detail Setting].
2. Touch [Machine Setting] → [Device Tele-
phone Number].
3. Input the Device telephone number using the
10-Key Pad and [P], [T], [W], [-].
(See P.257)
248 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
Step Procedure
bizhub 500/420/360
Using the telephone line Using the Fax line Using E-mail
modem modem *1
10 Inputting the AT com- Proceed to step 11. Setting the E-mail address
mand for initializing the 1. Select [Service Mode] → [CS Remote Care],
modem and touch [Server Set].
1. Select [Service 2. Touch [Server for RX], and set POP3 server
Mode] → [CS address, POP3 Login name, POP3 pass-
Remote Care] → word and POP3 port number.
and touch [Detail (See P.259)
Setting]. 3. Press [Receive], and set the E-Mail address,
2. Touch [AT Com- Mail Check, Connection Time Out and
mand]. APOP Authentication.
3. Input AT Com- (See P.260)
mand. 4. Touch [Send], and set the SMTP server
NOTE address, SMTP port number, Connection
• Change this Com- Time Out, and APOP Authentication.
mand only when it (See P.261)
is necessary. 5. Touch [TX/RX Test], and press Start key to
(They do not need carry out a transmission/reception test. If it
to be changed in fails to exchange messages, see the error
normal condition.) message to take necessary measure, and
• For details on AT try again.
Command, see (See P.262)
the manual for the
modem.
(See P.259)
11 Setting the DIPSW for CS Remote Care Proceed to Step 12.
NOTE
• This setting is not normally necessary.
Take this step only when necessary in a
specific connecting condition.
1 249
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Step Procedure
bizhub 500/420/360
Using the telephone line Using the Fax line Using E-mail
modem modem *1
12 Executing the initial transmission Receiving the initial connection E-mail message
1. Select [Service Mode] → [CS Remote Care], Sending the initial connection E-mail message
and touch [Detail Setting]. from the Center to the address of the Copier.
2. Touch [initial transmission] key on the right NOTE
bottom of the screen to start initial transmis- • When receiving the initial connection E-
sion. mail message from the Center while CS
3. When the machine is properly connected with Remote Care-related screen is being
the Center, CS Remote Care setting screen displayed, the current setting informa-
will be displayed. tion will be deleted, and CS Remote
NOTE Care setting will be displayed.
• The initial transmission key at the right • For sending the initial connection E-
bottom of the screen will be displayed mail, see the manual for CS Remote
only when the Center ID, the Device ID, Care Center.
Telephone number of the Center and the • Messages can be exchanged only
Device telephone number have been between the Center with initial connec-
input. tion and the Copier.
(See P.257) • The initial connection from the Center
will be carried out, and the E-mail
address of the Center will be stored in
the Copier.
• When the initial registration is complete,
the E-mail address of the Center will be
displayed by selecting [Service Mode] →
[CS Remote Care] → [Detail Setting],
[Basic Setting] → [E-Mail address].
*1: This procedure is available only when the optional Fax kit (FK-502) is mounted.
250 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Note
• SW bits data are written into the NVRAM every time a change is made. In case you changed bit
data by accident, be sure to restore the previous state.
A. Input procedure
1. Select [Service Mode] → [CS Remote Care] → [Detail Setting], and touch [Software Switch Setting].
2. Touch [Switch No.], and input the SW number (two digits) using the 10-Key Pad.
3. Touch [Bit Assignment], and select SW bit number using the arrow keys, and input 0 or 1 using the 10-Key
Pad.
(For setting by hexadecimal numbers, touch [HEX Assignment] key, and input using the 10-Key Pad or A
to F keys.)
4. Touch [Fix].
Note
• About functions of each switch, see to "B. List of software SW for CS Remote Care".
Note
• Do not change any bit not described on this table.
251
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
SW 04 0 to 7 Reservation — — 0
SW 05 0 Modem redial interval *2 *2 1
1 *2 *2 1
2 *2 *2 0
3 *2 *2 0
4 to 7 Reservation — — 0
SW 06 0 Modem redial times *3 *3 0
1 *3 *3 1
2 *3 *3 0
3 *3 *3 1
4 *3 *3 0
5 *3 *3 0
6 *3 *3 0
7 Reservation — — 0
SW 07 0 Redial for response time out Do not redial Redial 1
1 to 7 Reserved — — 0
SW 08 0 Retransmission interval on E-Mail deliv- *4 *4 0
1 ery error *4 *4 1
2 *4 *4 1
3 *4 *4 0
4 to 7 Reservation — — 0
SW 09 0 Retransmission times on E-Mail *5 *5 0
1 delivery error *5 *5 1
2 *5 *5 0
3 *5 *5 1
4 *5 *5 0
5 *5 *5 0
6 *5 *5 0
7 Reservation — — 0
SW 10 0 to 7 Reservation — — 0
SW 11 0 Timer 1 *6 *6 0
1 RING reception → CONNECT *6 *6 0
2 reception *6 *6 0
3 *6 *6 0
4 *6 *6 0
5 *6 *6 1
6 *6 *6 0
7 *6 *6 0
252
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
SW 12 0 Timer 2 *7 *7 0
1 Dial request completed → CONNECT *7 *7 0
2 reception *7 *7 0
3 *7 *7 0
4 *7 *7 0
5 *7 *7 0
6 *7 *7 1
7 *7 *7 0
SW 13 0 to 7 Reservation — — 0
SW 14 0 Timer 4 *8 *8 0
1 Line connection → Start request *8 *8 0
2 telegram delivery *8 *8 0
3 *8 *8 0
4 *8 *8 0
5 *8 *8 1
6 *8 *8 0
7 *8 *8 0
SW 15 0 Timer 5 *9 *9 0
1 Wait time for other side's response *9 *9 1
2 *9 *9 1
3 *9 *9 1
4 *9 *9 1
5 *9 *9 0
6 *9 *9 0
7 *9 *9 0
SW 16 0 to 7 Reservation — — 0
SW 17 0 to 7 Reservation — — 0
SW 18 0 Attention display Do not call Call 1
To set weather to give the alarm display
when using the modem but the power
for the modem is OFF.
1 to 7 Reservation — — 0
SW 19 to SW 0 to 7 Reservation — — 0
40
*1 Baud rate
253
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
254
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Mode 09-6 09-5 09-4 09-3 09-2 09-1 09-0
0 to 9 times 000 0000 to 000 1001
"10 times" 0 0 0 1 0 1 0
11 to 99 times 000 1011 to 110 0011
255
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
• Follow the steps below to make sure that CS Remote Care has been properly set up.
Note
• For transmitting data of the machine by calling the center on the specified date and time, refer to
the manual for CS Remote Care Center.
1. Select [Service Mode] → [CS Remote Care], and touch [Detail setting].
2. Touch [Communication Log Print].
3. Load Tray 1 or Bypass tray with A4S paper.
4. Press the Start key to output transmission log.
256
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
A. System Selection
B. ID Code
C. Detail Setting
(1) Basic Setting
Primary Setting
• Set the Center ID, Device ID, and the phone No.
• When e-mail is selected for system and all setup procedures are completed, E-mail
address of the Center is displayed.
* When entering the phone No, 10-Keys and keys on the screen have following meanings.
[–] Pose : Waits to start transmitting after dialing
[W] Wait : Detects the dial tone of the other end
[T] Tone dial : Carry out tone dialing
[P] Pulse dial : Carry out pulse dialing
[*], [#] : To be used as necessary
Initial Transmission
• Touching the Initial Transmission key will sent the information to the CS Remote Care
Center to register the machine.
(Only when the Modem or Fax is selected on the system Input.)
1 257
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
NOTE
• If RAM Clear is selected during transmission, RAM clear processing will be
implemented at the time the transmission is completed regardless of whether it
is done properly or not.
Setting/ • The default setting is “Unset.”
Procedure
Set “Unset”
258
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Functions • It sets the intervals for resending E-Mails when transmission error occurred.
• It can be set only when [E-Mail] is selected by System Setting.
Use • To use when changing the intervals for resending E-Mails when transmission error
occurred.
Setting/ • The default setting is 60 minute.
Procedure
“60 minute” (10 to 1440)
(7) AT Command
D. Server Setting
• Server Setting can be set only when [E-Mail] is selected by System Setting.
<Input FQDN>
• Enter the domain name.
<POP3 password>
Functions • To set the logon password for the POP3 server used for the CS Remote Care.
Use • To set the logon password for the POP3 server.
Setting/ • The default setting is No.
Procedure • Up to 15 characters (alphanumeric characters and symbols) can be used.
1 259
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Functions • To set the POP3 port number used for the CS Remote Care.
Use • To set the port number for the POP3 server.
Setting/ • The default setting is 110.
Procedure “110” (1 to 65535)
(2) Receive
<E-mail Address>
Functions • To set the e-mail address used for the CS Remote Care.
Use • To set the e-mail address.
Setting/ • The default setting is No.
Procedure • Up to 129 characters (alphanumeric characters and symbols) can be used.
<Mail Check>
Functions • To set whether or not to use Mail Check and the time interval for the POP server
used for the CS Remote Care.
Use • To set whether or not to use Mail Check and the time interval for the POP server
used for the CS Remote Care.
• To change the time interval for Mail Check.
Setting/ • The default setting is No.
Procedure “No” (1 to120 min., No)
<Connection timeout>
Functions • To set the timeout period for connection during reception.
Use • To change the timeout period for connection during reception.
Setting/ • The default setting is 60 Sec.
Procedure “60 Sec” (30 to 300 Sec)
<APOP Authentication>
Functions • To set whether or not to authenticate the APOP during reception.
Use • To authenticate the APOP during reception.
Setting/ • The default setting is No.
Procedure Yes “No”
260 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
(3) Send
bizhub 500/420/360
<SMTP server>
Functions • To set the SMTP sever address for transmission used for the CS Remote Care.
Use • To set the SMTP server address
• SMTP server address can be set by the IP address or the domain name.
Setting/ <Input IP Address>
Procedure • IP Address Version 4 format
[0 to 255].[0 to 255].[0 to 255].[0 to 255]
<Input FQDN>
• Enter the domain name.
<Authentication Setting>
Functions • To set whether or not to authenticate during transmission via SMTP server.
Use • To use when authenticating during transmission.
Available authentication mode: POP Before SMTP, SMTP authentication
Setting/ • The default setting is OFF.
Procedure
“OFF” POP Before SMTP SMTP Authentication
* Setting to “POP Before SMTP” will set the time for POP Before SMTP.
* When setting to SMTP authentication, touch the “Setting Check” key for authentica-
tion.
User ID : Enter the User ID for SMTP authentication.
Password : Enter the password for SMTP authentication.
Domain name : Enter the domain name for SMTP authentication.
1 261
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Functions • To determine the correct transmission and reception using CS Remote Care.
Use • Use to determine the correct transmission and reception using CS Remote Care.
Setting/ • Press the Start key to let the machine start the transmission and reception test.
Procedure • The test procedure and result will be displayed on the screen.
262 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
A. When Connecting by Modem
1 263
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
0018 Machine ID has already been registered • Set the initial registrations
(Request telegram 2 (SET-UP) comes from the again for all including the
main unit that has already registered Machine host side.
ID.)
0019 Center ID Error • Check Center ID setting of
(Center ID of the host is not identical with the the main unit side.
one of start request telegram.) • Check Center ID setting of
the main unit side.
001A Device ID inconsistency • Check Device ID setting of
(Device ID of the host is not identical with the the main unit side.
one of start request telegram.) • Check the setting of the
host side.
001B Device ID Unregistered • Check Device ID setting of
(Request telegram 2 (Constant data transmit- the main unit side.
ting, Emergency call) comes from the main unit • Check the setting of the
that has not registered Machine ID yet.) host side.
001E Impossible to change (During printing) • Try again when the machine
(Setting cannot be changed because the setting is not printing.
change is made during the machine is printing or
starts printing.)
0020 Timeout of Telegram Delivery • Try communication again.
(At waiting mode of telegram delivery the
machine fails to receive the telegram in a given
time.)
0027 Transmission / Receiving collision • Try communication again.
(Receiving is detecting during transmitting pro-
cessing)
Note
• When a code other than the ones listed above is displayed, contact KONICA MINOLTA and inform
the error code.
264 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
1062 Modifying not available due to the copy job cur- • Ask the host to send
rently performing another instruction mail for
• When informing the host that it cannot be modifying.
modified due to the copy job currently per-
forming.
1081 Frame No. error • Check the status of the
• The last frame has not been received. Machine registration on host
• There are missing frame No. side.
1084 Date expired • Ask the host to send
• Expiration date for data modification com- another instruction mail for
mand has passed. modifying.
1092 Received an error mail when Center setup is not • Check the status of the
complete Machine registration on host
side.
2039 Socket is not connected. • Check the SMTP Server and
• LAN cable on the Copier side is detached. POP3 Server on User side.
203E Network is down. • Check the connection
• LAN cable on the Copier side is detached. between the Copier on the
User’s side and the Network
connector.
• Check the Network environ-
ment on the User’s side.
3000 POP3_AUTHORIZATION_ERR • Check the POP3 Server
environment on User’s side.
3001 POP3_TRANSACTION_ERR • Check the POP3 Server
environment on User’s side.
3002 POP3_CONNECT_ERR • Check the POP3 Server
environment on User’s side.
3003 POP3_TIMEOUT_ERR • Check the POP3 Server
environment on User’s side.
3004 POP3_FORMAT_ERR • Check the POP3 Server
environment on User’s side.
3005 POP3_MEMORY_ERR • Check the POP3 Server
environment on User’s side.
3006 POP3_JOBID_ERR • Check the POP3 Server
environment on User’s side.
3007 POP3_NO_DATA_ERR • Check the POP3 Server
environment on User’s side.
3008 POP3_DELETE_FAIL_ERR • Check the POP3 Server
environment on User’s side.
3009 POP3_MAILBOX_FULL • Check the POP3 Server
environment on User’s side.
4103 Not Ready • Wait for a while and try
• Tried to transmit or receive an E-Mail when transmitting again.
the machine was not yet in the E-Mail receiv-
ing status after power was turned ON.
1 265
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
4104 SMTP Channel Not Ready • Wait for a while and try
transmitting again.
4105 POP3 Channel Not Ready • Wait for a while and try
transmitting again.
4106 Not Ready other than the ones listed above. • Wait for a while and try
transmitting again.
Note
• When a code other than the ones listed above is displayed, contact KONICA MINOLTA and inform
the error code.
Note
• When a code other than the ones listed above is displayed, see the FK-502 Service Manual.
266 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
If communication is not done properly, check the condition by following the procedures shown below.
1. Shift the screen in the order of [Service Mode] → [CS Remote Care] → [Detail Setting].
At this time, in the cases of Initial transmitting / Administrator transmitting / Maintenance Start transmitting
/ Maintenance Finish transmitting, the communication result will be displayed at the top of the screen.
* For the communication result, the following message will be displayed based on its success or failure.
267
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.12System 2
bizhub 500/420/360
A. Procedure
Note
• Be sure not to change the setting of DipSW that is not given in this service manual.
A. Procedure
268
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Note
• Be sure not to change bits with no particular reference made of the function.
1 269
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
270 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Japan Inch Metric
DipSW9 0 Copy quantity limit *4 *4 0 0 0
1 *4 *4 0 0 0
2 *4 *4 0 0 0
3 *4 *4 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW10 0 — — — 0 0 0
1 — — — 1 1 1
2 — — — 1 1 1
3 — — — 0 0 0
4 — — — 0 0 0
5 Download font display setting *5 *5 0 0 0
6 *5 *5 0 0 0
7 Jam code display Not displayed Displayed 1 1 1
DipSW11 0 — — — 0 0 0
1 — — — 1 1 1
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW12 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 Print count setting up to the *6 *6 0 0 0
4 print inhibition when getting at *6 *6 0 0 0
5 PM *6 *6 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW13 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 Jaggy filter selection OFF ON 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 Discrimination level of the non- *7 *7 1 1 1
7 image auto erase mode *7 *7 0 0 0
1 271
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
272 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Japan Inch Metric
DipSW18 0 Separation of a defective part Normal Separated 0 0 0
from the tray 1 (upper stage of
the main body)
1 Separation of a defective part Normal Separated 0 0 0
from the tray 2 (lower stage of
the main body)
2 Separation of a defective part Normal Separated 0 0 0
from the bypass feed
3 — — — 0 0 0
4 Separation of a defective part Normal Separated 0 0 0
from the tray 3 (PC-202 upper
stage/PC-402)
5 Separation of a defective part Normal Separated 0 0 0
from the tray 4 (PC-202 lower
stage)
6 Separation of a defective part Normal Separated 0 0 0
from the tray 5 (LU)
7 — — — 0 0 0
DipSW19 0 Separation of a defective part Normal Separated 0 0 0
from the printer controller (IC)
1 Separation of a defective part Normal Separated 0 0 0
from the FAX kit (FK)
2 — — — 0 0 0
3 Separation of a defective part Normal Separated 0 0 0
from HDD
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Separation of a defective part Normal Separated 0 0 0
from DF
DipSW20 0 Separation of a defective part Normal Separated 1 1 1
from the network
1 Separation of a defective part Normal Separated 0 0 0
from IEEE1284
2 Separation of a defective part Normal Separated 0 0 0
from USB
3 — — — 0 0 0
4 — — — 0 0 0
5 Separation of a defective part Normal Separated 0 0 0
from SD
6 — — — 0 0 0
7 — — — 0 0 0
1 273
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
274 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Japan Inch Metric
DipSW24 0 Mixed original direction setting Not detected Detected 0 0 0
1 job history display setting Valid Invalid 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW25 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 Switchover of the TSL control Normally All OFF 0 0 0
ON/OFF
4 — — — 0 0 0
5 — — — 0 0 0
6 Image rotation when stapling is Not rotate rotate to 180° 0 0 0
not selected
7 — — — 0 0 0
DipSW26 0 Polygon motor stop timer 15 seconds 30 seconds 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 Reference image position for At the center On the rear 0 0 0
bypass custom paper side of paper
4 RS-232C I/F setting Valid Invalid 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW27 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 Density setting when the *12 *12 0 0 0
6 printer toner save function is *12 *12 0 0 0
7 selected. *12 *12 0 0 0
DipSW28 0 Image leading edge position *13 *13 0 0 0
1 adjustment while in the image *13 *13 0 0 0
2 rotation *13 *13 0 0 0
3 *13 *13 0 0 0
1 275
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
276 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Japan Inch Metric
DipSW33 5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DipSW34 0 System ON/OFF while in the ON OFF 1 1 1
sleep or the power switch
(SW2) OFF
1 FS-510 paper exit tray position *20 *20 0 0 0
2 *20 *20 0 0 0
3 *20 *20 0 0 0
4 Print start permission when Permit Prohibit 0 0 0
SD-502 is supplied with paper.
5 — — — 0 0 0
6 USB function ISW mode Printer mode 1 1 1
7 — — — 0 0 0
DipSW35 0 Custom original support *21 *21 0 0 0
1 *21 *21 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 Stitch direction correction in 2 Valid Invalid 0 0 0
→ 2 mode
5 Address book password Valid Invalid 0 0 0
export permission setting
6 Address setting after sending Reset Not reset 0 0 0
through the scanner
7 — — — 0 0 0
DipSW36 0 IPX used or not used Not used Used 1 1 1
1 Telnet used or not used Not used Used 0 0 0
2 Fusing temperature setting *22 *22 0 0 0
3 when normal paper is selected *22 *22 0 0 0
4 Fusing temperature setting *23 *23 0 0 0
when thick paper, envelope or
label is selected
5 Fusing temperature setting *24 *24 0 0 0
when thin paper is selected.
6 Fusing temperature setting *25 *25 0 0 0
7 when OHP is selected. *25 *25 0 0 0
1 277
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
278 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Set the copy count that is printed until the print oper-
After 0 print or its equiva- 0 0
ation is terminated from the toner near empty is dis-
lent
played after the toner level sensor (PZS) detects toner
After 100 print or its 0 1
empty for a certain period of time.
equivalent
After 200 print or its 1 0
equivalent
After 500 print or its 1 1
equivalent
*2 Print stop condition after the toner supply display Mode 4-3 4-2
Set the copy count that is printed until the print is pro-
100 prints or its equiva- 0 0
hibited after a message set by DipSW4-0/1 is dis-
lent
played.
400 prints or its equiva- 0 1
lent
700 prints or its equiva- 1 0
lent
1000 prints or its equiva- 1 1
lent
279
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
No limit 0 0 0 0
1 print 0 0 0 1
3 prints 0 0 1 0
5 prints 0 0 1 1
9 prints 0 1 0 0
10 prints 0 1 0 1
20 prints 0 1 1 0
30 prints 0 1 1 1
50 prints 1 0 0 0
99 prints 1 0 0 1
250 prints 1 0 1 0
No limit 1 0 1 1
No limit 1 1 0 0
No limit 1 1 1 0
No limit 1 1 1 1
*6 Setting of the print count made up to the time of Mode 12-5 12-4 12-3
the print inhibition when gettint to PM
1000 prints 0 0 0
When getting at DipSW8-2PM with the print inhibition
2000 prints 0 0 1
set to "1," the print stops after getting at the PM
3000 prints 0 1 0
count shown on the right.
4000 prints 0 1 1
5000 prints 1 0 0
280 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Set the fusing temperature while in the low power
The fusing heater lamps /1 (L2) and /2 0 0
mode.
(L3) turn on when the thermistors /1
(TH1) and /2 (TH2) are respectively at
70 °C, and turn OFF when they are at
80 °C.
The fusing heater lamps /1 (L2) and /2 0 1
(L3) turn ON when the thermistors /1
(TH1) and /2 (TH2) are respectively at
120 °C, and turn OFF when they are at
130 °C.
The fusing heater lamps /1 (L2) and /2 1 0
(L3) turn ON when the thermistors /1
(TH1) and /2 (TH2) are respectively at
150 °C, and turn OFF when they are at
160 °C.
The fusing heater lamps /1 (L2) and /2 1 1
(L3) turn ON when the thermistors /1
(TH1) and /2 (TH2) are respectively at
70 °C, and turn OFF when they are at
80 °C.
81/4 x 13 0 0 1
8 /8 x 13 /4
1 1
0 1 0
8 x 13 0 1 1
1 281
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
*11 Platen small size (81/2 x 11/A4 or less) setting Mode 21-5
bizhub 500/420/360
*12 Density setting when selecting the printer toner Mode 27-7 27-6 27-5
save function.
Standard 0 0 0
When "Toner save mode" for the printer driver turns
– 4 (thin) 0 0 1
ON, set the printer density in the range shown in the
table. –3 0 1 0
–2 0 1 1
–1 1 0 0
+1 1 0 1
+2 1 1 0
+ 3 (dense) 1 1 1
*13 Adjustment of the image leading edge while in Mode 28-3 28-2 28-1 28-0
the image rotation
+ 0 mm 0 0 0 0
While in the location in the 1-sided/2-sided copy,
+ 0.5 mm 0 0 0 1
adjust the slippage at the leading edge when there
occurs a leading edge slippage of 3 to 4 mm on the – 0.5 mm 1 0 0 1
*14 Adjustment of the image leading edge position Mode 28-7 28-6 28-5 28-4
while in the platen memory copy
+ 0 mm 0 0 0 0
While in the platen copy, the paper exit direction is
+ 0.5 mm 0 0 0 1
reversed for the normal print and the memory print.
Adjust the discrepancy when the image leading edge – 0.5 mm 1 0 0 1
*15 Selection of the transfer/separation output of the Mode 29-2 29-1 29-0
user paper (tray)
Normal paper (Japan) 0 0 0
Set the transfer/separation output that is applicable
Normal paper (inch) 0 0 1
when selecting the user paper in [Paper type] of [Util-
ity menu]. Normal paper (metric) 0 1 0
Thick paper 0 1 1
Thin paper 1 0 0
Recycled paper 1 0 1
282
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
*16 TSL control of the user paper (tray) Mode 29-4 29-3
bizhub 500/420/360
Set the TSL control that is applicable when selecting
Normal ON control 0 0
the user paper in [Paper type] of [Utility menu]. When
All OFF 0 1
selecting "Switch over depending on the environ-
Switching over depending 1 0
ment," conduct the TSL control by switching over
on the environment
"Normal ON control"/"All OFF" according to the
humidity detected by the humidity sensor (HUMS).
*17 Selection of the transfer/separation output of the Mode 30-2 30-1 30-0
user paper (bypass)
Normal paper (Japan) 0 0 0
When selecting the bypass tray, set the transfer/sep-
Normal paper (inch) 0 0 1
aration output that is applicable when the user paper
is selected in [Specialty paper] of "Change Tray set- Normal paper (metric) 0 1 0
*18 TSL control of the user paper (bypass) Mode 30-4 30-3
When selecting the bypass tray, set the TSL control
Normal control 0 0
that is applicable when the user paper is selected in
All OFF 0 1
[Specialty paper] of "Change Tray settings" or when it
is selected in [Paper type] of [Utility menu]. Switching over depending 1 0
*19 Switchover of the punch hole number (PU) Mode 33-1 33-0
While in the use of PU-501, set the number of punch
2 holes (Japan) 0 0
holes to be displayed on the operation board. This
3 holes (inch) 0 1
can be set regardless of the destination of the main
body. 4 holes (metric) 1 0
Default setting is 3 holes for inch and 4 holes for met- 4 holes (Sweden) 1 1
ric.
283
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
*20 FS-510 paper exit tray position Mode 34-3 34-2 34-1
bizhub 500/420/360
*22 Fusing temperature setting while in the selection Mode 36-3 36-2
of plain paper
Standard 0 0
When there occurs a problem (insufficient fusing,
Standard + 10 °C 0 1
large paper curl) with fusibility while in the selection of
Standard + 5 °C 1 0
plain paper, change the fusing set temperature.
• Countermeasure Standard – 10 °C 1 1
1) Increase the temperature: To suppress a jam
due to an insufficient fusing and the wind-up of
paper around the roller.
2) Decrease the temperature: To suppress a
paper curl and the undulation of paper.
284 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
*25 Fusing temperature setting while in the selection Mode 36-7 36-6
bizhub 500/420/360
of OHP
Standard 0 0
When there occurs a problem (insufficient fusibility
Standard + 10 °C 0 1
and large paper curl) with fusibility while in the selec-
Standard – 20 °C 1 0
tion of OHP, change the fusing set temperature. (For
countermeasure, see *22.) Standard – 10 °C 1 1
*26 Operation at setting paper onto the bypass feed Mode 38-4 38-3
tray
Reset size with selecting 0 0
Set the operation when setting paper onto the
the bypass feed tray
bypass feed tray.)
Does not reset size with 0 1
selecting the bypass feed
tray
Reset size without select- 1 0
ing the bypass feed tray
Reset size without select- 1 1
ing the bypass feed tray
1 285
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.12.4 ISW
bizhub 500/420/360
10.12.5 Option
Let the main body recognize the installing condition of the optional HDD and FAX.
A. Procedure
A. Procedure
286 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
After completion of the handling of a trouble related to the fusing system, release the trouble.
Note
• When a trouble related to the fusing system occurs, the software DipSW3-1 (SC latch) is set to "1"
("0" for default). This adjustment is used to return this to the default condition (normal operation).
• When an SC code is displayed on the touch panel, you cannot enter the service mode. Accord-
ingly, the following shows the method for resetting a trouble from the power-off condition.
A. Procedure
1 287
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.13List Output
bizhub 500/420/360
A. Procedure
288 1
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
10.14Test Mode
bizhub 500/420/360
10.14.1 Test pattern list
The following test patterns can be output.
• Full Image Halftone (No. 1)
• Gradation Pattern (No. 2)
• Gradation Pattern (No. 3)
• Gradation Pattern (No. 5)
• Beam Gap Check (No. 11)
• Line Check Pattern (No. 16)
Note
• Be sure not to output a test pattern that is not given in this service manual.
289
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
[Check item]
• When the density is set at 70 (halftone)
When there are white stripes or black stripes, check to see if an abnormality is found with the scanner
system or process system
[Recommended sections to be checked]: Developing unit, cleaning glass, charging corona, transfer/sep-
aration corona, scanner mirror, slit glass and original glass
• When the density is set at 0 (white)
When an image fogging occurs, check the process system to see if an abnormality is found with it.
[Recommended sections to be checked]: Charging corona, and the contact of a high voltage power
source
• When the density is set at 255 (black)
When the density is thin, check the process system to see if an abnormality is found with it.
[Recommended sections to be checked]: Write unit
Test pattern
When the density is set at 70. When the density is set at 0. When the density is set at 255.
50gaf3c007na
290
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
No.2 Gradation pattern
[Check item]
When fogging appears or density is thin, check the process system and the gamma correction to see if which
is defective.
Regardless of this test pattern being normal, any trouble is found with the print image, the image processing
system or scanner system is considered defective.
Test patterns
50gaf3c013na
291
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
[Check item]
• Check to see if the laser output of LD1/LD2 is uniform and if the gradation is reproduced without a break.
[Recommended sections to be checked]: Write unit, and LD offset adjustment
* For LD offset adjustment, see "10.4.11 LD1 Offset Adj. / LD2 Offset Adj.".
(See P.194)
Test pattern
LD1 LD2
50gaf3c008na
292
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
No.5 Gradation pattern (8-bit output)
[Check item]
• Check the pattern to see if the laser output of LD1/LD2 is uniform with the gradation continuously repro-
duced.
[Recommended checkpoints]: Write unit, LD offset adjustment
* For LD offset adjustment, see "10.4.11 LD1 Offset Adj. / LD2 Offset Adj.".
(See P.194)
Test pattern
LD1 LD2
50gaf3c009na
293
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
[Check item 1]
• Check to see if there is a difference in density found with the solid black pattern in the main scan and sub
scan directions.
[Recommended sections to be checked]: Charging corona, transfer/separation corona, developing unit,
and write dust-proof glass.
[Check item 2]
• Check to see if an image crawling occurs with the gradation pattern at the leading edge and/or trailing
edge of the test pattern in the sub scan direction.
[Recommended sections to be checked]: Transfer/separation corona
Test pattern
[1]
[2]
50gaf3c010na
294
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
No.16 Linearity evaluation pattern (1-bit error diffusion output)
[Check item]
Judge from this test pattern whether the scanner system or the printer system is abnormal.
Items that can be checked include main scan magnification, sub scan magnification, image skew, and leading
edge timing of the printer system. If the copy image is defective despite no abnormality being visible on the
test pattern, the scanner system is defective.
Test pattern
[1]
31mm 237mm
20mm
[1]
190mm
m
m
0
28
205.7mm
28
0m
m
190mm
190mm 50gaf3c011na
295
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
There are two methods provided for the test pattern output.
• Output it by selecting the item of each test pattern. (Procedure A)
• Output it by specifying the test pattern number. (Procedure B)
Note
• Be sure not to output a test pattern that is not given in this service manual.
296
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Conduct a continuous print operation test.
In this mode, the following items can be selected.
• Paperless Mode
With no paper fed and none of the paper detection/jam detection made, the print operation is made nearly at
the same timing as the usual operation.
A. Procedure
297
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.15Fax setting
bizhub 500/420/360
298
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
10.16Enhanced Security
bizhub 500/420/360
10.16.1 List of the security setting
Adjustment/setting item
Enhanced Security CE Password
Administrator Password
Administrator Feature Level Level 1
Level 2
Prohibit
CE Authentication ON
OFF
A. Procedure
299
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.16.3 CE Password
bizhub 500/420/360
Note
• Be sure to avoid using as a password the name and the birth day that can be easily suspected by
other people.
• CE must not leak the password to other people.
• The CE password is valid when the CE authentication function is valid.
(See P.301)
A. Procedure
Note
• Be sure to avoid using as a password the name and the birth day that can be easily suspected by
other people.
A. Procedure
300
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Set the range of the administrator feature to be displayed in Administrator Setting in the Utility menu. When the
setting is made to [Prohibit] in this feature, the following features are not displayed.
[3] Administrator setting [1] System setting [0] Standard Size setting
B. Procedure
10.16.6 CE Authentication
Set the request or non-request of the password entry to enhance the security level in the service mode.
A. Procedure
301
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
10.17Billing Setting
bizhub 500/420/360
Adjustment/setting item
Billing Setting Counter Setting
Management Function Choice
A. Procedure
302
Field Service Ver.2.0 Jan. 2007 10. SERVICE MODE
bizhub 500/420/360
Set the counter mode of the counters of 2 types.
• Total Counter Mode
• Large Size Counter Mode
A. Procedure
NOTE
• When selecting other than [No count], the count-up is as shown below in the combination of the
total counter and the counter mode.
4. Press [END].
303
10. SERVICE MODE Field Service Ver.2.0 Jan. 2007
Set the installation/non-installation of the key counter and the management device.
A. Procedure
NOTE
• The initial setting is [Unset].
3. Select the message type.
4. Press [END].
304
Field Service Ver.2.0 Jan. 2007 11. MECHANICAL ADJUSTMENT
bizhub 500/420/360
11.1 Mis-centering adjustment of the trays 1 and 2
This adjustment is made when there occurs a mis-centering that cannot be adjusted in the service mode.
A. Procedure
1. Pull out the tray [1].
2. If there remains any paper, remove it thoroughly.
3. When the paper guide [2] is set to the small size
position, expand it.
4. Loosen the 2 screws [3].
5. Move the paper guide [2] and adjust the center
position with the marking-off [4] as a guide.
6. Tighten the 2 screws [3].
[1] 50gaf3c014na
50gaf3c015na
305
11. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
This adjustment is made when there occurs a mis-centering that cannot be adjusted in the service mode.
A. Procedure
1. Open the bypass tray [1].
2. If paper is set, remove it.
3. When the paper guide [2] is set to the small size
position, expand it.
4. Loosen the 2 screws [3].
5. Move the paper guide [2] and adjust the center
[4] position with the marking-off [4] as a guide.
6. Tighten the 2 screws [3].
[2] [1]
[2] [3]
50gaf3c016na
50gaf3c017na
306
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
TROUBLESHOOTING
bizhub 500/420/360
12. JAM CODE
12.1 Jam code list
does not turn ON within a specified sheet of paper the bypass tray and
period of time after the feed clutch being printed remove jammed paper
/BP (CL6) turns ON. when a jam if any.
Tray 1 J-1100 The registration sensor (PS1) does occurs, the main Open the vertical con-
not turn ON within a specified period body completes veyance door and ADU
of time after the feed clutch /1 (CL4) the paper exit and remove jammed
turns ON. before stopping paper if any.
Tray 2 J-1200 The vertical conveyance sensor (PS2) operations. Pull out the tray and
does not turn ON within a specified remove jammed paper
period of time after the feed clutch /2 if any.
(CL5) turns ON.
J-1201 The registration sensor (PS1) does
not turn ON within a specified period
of time after the vertical conveyance
sensor (PS2) turns ON.
PC-202 J-1300 The vertical conveyance sensor /3 Open the right door of
(PS117) does not turn ON a specified PC and the vertical
period of time after the paper feed conveyance door of the
motor /3 (M122) turns ON. main body and remove
PC-402 The vertical conveyance sensor (PS2) jammed paper if any.
does not turn ON a specified period Pull out the tray and
of time after the paper feed motor remove jammed paper
(M1) turns ON. if any.
PC-202 J-1301 The vertical conveyance sensor (PS2)
of the main body does not turn ON
within a specified period of time after
the vertical conveyance sensor /3
(PS117) of PC-202 turns ON.
PC-402 J-1302 The vertical conveyance sensor (PS2)
of the main body does not turn ON
within a specified period of time after
the vertical conveyance sensor (PS2)
of PC-402 turns ON.
J-1305 The paper feed sensor (PS1) does not
turn ON within a specified period of
time after the paper feed motor (M1)
turns ON.
307
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
PC-402 J-1306 The paper feed sensor (PS1) does not If there is a Open the right door of
During operation
turn OFF within a specified period of sheet of paper PC and the vertical
time after the PS1 turns ON. being printed conveyance door of the
J-1307 The vertical conveyance sensor (PS2) when a jam main body and remove
does not turn ON within a specified occurs, the main jammed paper if any.
period of time after the paper feed body completes Pull out the tray and
sensor (PS1) turns ON. the paper exit remove jammed paper
J-1308 The paper feed sensor (PS2) does not before stopping if any.
turn OFF within a specified period of operations.
time after the PS2 turns ON.
J-1309 When a paper feed start signal is sent
out to PC-402 from the main body, a
recieve signal from PC-402 is not sent
out within a specified period of time
after that.
J-1311 The shift position sensor (PS11) does
not turn ON within a specified period
of time after shift home sensor (PS12)
turns OFF.
PC-202 J-1400 The vertical conveyance sensor /4
(PS126) does not turn ON within a
specified period of time after the
paper feed motor /4 (M123) turns ON.
J-1401 The vertical conveyance sensor /3
(PS117) does not turn ON within a
specified period of time after the verti-
cal conveyance sensor /4 (PS126)
turns ON.
LU J-1500 The LU exit sensor (PS155) does not Open the upper door of
turn ON within a specified period of LU and the vertical
time after the feed clutch (CL151) conveyance door of the
turns ON. main body and remove
J-1501 The vertical conveyance sensor (PS2) jammed paper if any.
of the main body does not turn ON
within a specified period of time after
the LU exit sensor (PS155) turns ON.
Other J-2001 Emergency stop jam of the system The main body Remove jammed paper
J-2002 While in the print, the vertical convey- and the optional if any from optional
ance door opens. device stop device / main body.
J-2003 The ADU door is opened while in immediately.
printing.
J-2004 The ADU is opened while in printing.
PC J-2005 While in the print, the right door
opens.
308
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
bizhub 500/420/360
operation
FS J-2006 While in the print, the front door The main body Remove jammed paper
During operation
opens. and the optional if any from optional
FS-510 J-2007 While in the print, the guide plate device stop device / main body.
switch (SW4) turns OFF. immediately.
While in the up drive operation of the
tray, the shutter switch (SW2) turns
ON.
FS-511 J-2008 While in the print, FS-511 comes off
from the main body.
RU J-2009 While in the print, the front door
opens.
FS-511 J-2010 While in the print, the upper door
opens.
MT While in the print, the right door
opens.
SD While in the print, the saddle-stitching
section opens.
Conveyance J-3000 The registration sensor (PS1) does The printer sec- Open ADU and remove
not turn OFF within a specified period tion stops jammed paper if any.
of time after the registration clutch immediately.
(CL1) turns ON.
J-3100 The fusing exit sensor (PS3) does not
turn ON within a specified period of
time after the registration clutch (CL1)
turns ON.
Fusing J-3200 The fusing exit sensor (PS3) does not
turn OFF within a specified period of
time after the PS3 turns ON.
Reversing J-3300 The reverse sensor (PS27) does not
turn ON within a specified period of
time after the fusing exit sensor (PS3)
turns ON.
J-3400 The reverse sensor (PS27) does not
turn OFF within a specified period of
time after the PS27 turns ON.
Other J-5001 A print start signal is not sent out from The main body Open the right door of
the overall control board (OACB) and the optional PC, the vertical convey-
within a specified period of time after device stop ance door of the main
the registration sensor (PS1) turns immediately. body and ADU and
ON. remove jammed paper
if any.
309
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
DF J-6001 The DF open/close switch (SW3) The DF stops Open the open/close
During operation
turns OFF while in the DF operation. immediately. If cover and remove
J-6002 The cover open/close sensor (PS7) there is paper jammed paper if any.
turns OFF while in the DF operation. being trans-
J-6101 While in the single sided mode, the ferred or having
original feed sensor (PS6) does not been trans-
turn ON within a specified period of ferred, the main
time after the original feed motor (M1) body completes
turns ON. the paper exit
before stopping
J-6102 When feeding the first original in the
operations.
mode other than the single sided
mode, the original feed sensor (PS6)
does not turn ON within a specified
period of time after the original feed
motor (M1) turns ON.
J-6103 When feeding the second original in
the mode other than the single sided
mode, the original feed sensor (PS6)
does not turn ON within a specified
period of time after the original feed
motor (M1) turns ON.
J-6104 When feeding the third original in the
mode other than the single sided
mode, the original feed sensor (PS6)
does not turn ON within a specified
period of time after the original feed
motor (M1) turns ON.
J-6105 While in the single sided mode, the
original feed sensor (PS6) does not
turn OFF within a specified period of
time after the PS6 turns ON.
J-6106 When feeding the first original in the
mode other than the single sided
mode, the original feed sensor (PS6)
does not turn OFF within a specified
period of time after the PS6 turns ON.
J-6107 When feeding the second original in
the mode other than the single sided
mode, the original feed sensor (PS6)
does not turn OFF within a specified
period of time after the PS6 turns ON.
310
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
bizhub 500/420/360
operation
DF J-6108 When feeding the third original in the The DF stops Open the open/close
During operation
mode other than the single sided immediately. If cover and remove
mode, the original feed sensor (PS6) there is paper jammed paper if any.
does not turn OFF within a specified being trans-
period of time after the PS6 turns ON. ferred or having
been trans-
J-6201 While in the single sided mode, the
ferred, the main
original registration sensor (PS9) does
body completes
not turn ON within a specified period
the paper exit
of time after the feed motor (M1) turns
before stopping
ON.
operations.
J-6202 When feeding the first original in the
mode other than the single sided
mode, the original registration feed
sensor (PS9) does not turn ON within
a specified period of time after the
feed motor (M1) turns ON.
J-6203 When feeding the second original in
the mode other than the single sided
mode, the original registration sensor
(PS9) does not turn ON within a spec-
ified period of time after the feed
motor (M1) turns ON.
J-6204 When feeding the third original in the
mode other than the single sided
mode, the original registration sensor
(PS9) does not turn ON within a spec-
ified period of time after the feed
motor (M1) turns ON.
J-6205 While in the single sided mode, the
original registration sensor (PS9) does
not turn OFF within a specified period
of time after the PS9 turns ON.
J-6206 When feeding the first original in the
mode other than the single sided
mode, the original registration sensor
(PS9) does not turn OFF within a
specified period of time after the PS9
turns ON.
J-6207 When feeding the second original in
the mode other than the single sided
mode, the original registration sensor
(PS9) does not turn OFF within a
specified period of time after the PS9
turns ON.
311
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
DF J-6208 When feeding the third original in the The DF stops Open the open/close
During operation
mode other than the single sided immediately. If cover and remove
mode, the original registration sensor there is paper jammed paper if any.
(PS9) does not turn OFF within a being trans-
specified period of time after the PS9 ferred or having
turns ON. been trans-
J-6301 While in the single sided mode, the ferred, the main
original detection sensor (PS8) does body completes
not turn ON within a specified period the paper exit
of time after the original coveyance before stopping
motor (M2) turns ON. operations.
J-6302 When feeding the first original in the
mode other than the single sided
mode, the original detection sensor
(PS8) does not turn ON within a spec-
ified period of time after the original
coveyance motor (M2) turns ON.
J-6303 When feeding the second original in
the mode other than the single sided
mode, the original detection sensor
(PS8) does not turn ON within a spec-
ified period of time after the original
coveyance motor (M2) turns ON.
J-6304 When feeding the third original in the
mode other than the single sided
mode, the original detection sensor
(PS8) does not turn ON within a spec-
ified period of time after the original
coveyance motor (M2) turns ON.
J-6305 While in the single sided mode, the
original detection sensor (PS8) does
not turn OFF within a specified period
of time after the PS8 turns ON.
J-6306 When feeding the first original in the
mode other than the single sided
mode, the original detection sensor
(PS8) does not turn OFF within a
specified period of time after the PS8
turns ON.
J-6307 When feeding the second original in
the mode other than the single sided
mode, the original detection sensor
(PS8) does not turn OFF within a
specified period of time after the PS8
turns ON.
312
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
bizhub 500/420/360
operation
DF J-6308 When feeding the third original in the The DF stops Open the open/close
During operation
mode other than the single sided immediately. If cover and remove
mode, the original detection sensor there is paper jammed paper if any.
(PS8) does not turn OFF within a being trans-
specified period of time after the PS8 ferred or having
turns ON. been trans-
J-6501 While in the idle, the original feed sen- ferred, the main
When idling
1 313
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
DF J-6514 While in the idle, any of the original The DF stops Open the open/close
When idling
registration sensor (PS9), the original immediately. If cover and remove
detection sensor (PS8) or the original there is paper jammed paper if any.
exit sensor (PS10) is ON. being trans-
J-6515 While in the idle, any of the original ferred or having
feed sensor (PS6), the original regis- been trans-
tration sensor (PS9), the original ferred, the main
detection sensor (PS8) or the original body completes
exit sensor (PS10) is ON. the paper exit
J-6601 While in the single sided mode, the before stopping
During operation
314 1
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
bizhub 500/420/360
operation
DF J-6607 When feeding the second original in The DF stops Open the open/close
During operation
the mode other than the single sided immediately. If cover and remove
mode, the original exit sensor (PS10) there is paper jammed paper if any.
does not turn OFF within a specified being trans-
period of time after the PS10 turns ferred or having
ON. been trans-
J-6608 When feeding the third original in the ferred, the main
mode other than the single sided body completes
mode, the original exit sensor (PS10) the paper exit
does not turn OFF within a specified before stopping
period of time after the PS10 turns operations.
ON.
FS-510 J-7201 While in the idle, the entrance sensor FS, RU, MT, SD, Remove jammed paper
When idling
315
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
FS-510 J-7217 The entrance sensor (PS4) does not FS, RU, MT, SD, Remove jammed paper
During operation
turn OFF within a specified period of main body stop if any from the FS/main
time after the PS4 turns ON. immediately. body.
The conveyance sensor (PS5) does
not turn ON within a specified period
of time after the entrance sensor
(PS4) turns ON.
FS-511 The path sensor (PS2) of RU does not
turn OFF within a specified period of
time after the PS2 turns ON.
The sub tray paper exit sensor (PS1)
of FS does not turn ON within a spec-
ified period of time after the path sen-
sor (PS2) of RU turns ON.
The main route conveyance sensor
(PS4) of FS does not turn ON within a
specified period of time after the path
sensor (PS2) of RU turns ON.
The bypass route conveyance sensor
(PS2) of FS does not turn ON within a
specified period of time after the path
sensor (PS2) of RU turns ON.
The main route conveyance sensor
(PS4) does not turn OFF within a
specified period of time after the PS4
turns ON.
The bypass route conveyance sensor
(PS2) does not turn OFF within a
specified period of time after the PS2
turns ON.
The intermediate conveyance sensor
(PS3) does not turn ON within a spec-
ified period of time after the main
route conveyance sensor (PS4) turns
ON.
The intermediate conveyance sensor
(PS3) does not turn OFF within a
specified period of time after the
bypass route conveyance sensor
(PS2) turns ON.
FS-510 J-7218 The conveyance sensor (PS5) does
not turn OFF within a specified period
of time after the PS5 turns ON.
FS-511 The sub tray exit sensor (PS1) does
not turn OFF within a specified period
of time after the PS1 turns ON.
316
Field Service Ver.2.0 Jan. 2007 12. JAM CODE
bizhub 500/420/360
operation
FS-511 J-7218 The intermediate conveyance sensor FS, RU, MT, SD, Remove jammed paper
During operation
(PS3) does not turn OFF within a main body stop if any from the FS/main
specified period of time after the PS3 immediately. body.
turns ON.
FS-510 J-7221 After completion of stapling, the
stacker sensor (PS8) does not turn
OFF within a specified period of time
after the paper exit motor (M1) turns
ON.
FS-511 After completion of stapling, the align-
ment tray sensor (PS5) does not turn
OFF within a specified period of time
after the paper exit motor (M3) turns
ON.
SD J-7225 Folding jam
PU J-7243 Punch jam
FS-510 J-7281 The stapler motor does not return to
the home position within a specified
period of time after the stapler motor
turns ON.
FS-511 The stapler home sensor /Fr (PS22)
does not turn ON within a specified
period of time after the stapler motor
/Fr (M16) turns ON.
J-7282 The stapler home sensor /Rr (PS25)
does not turn ON within a specified
period of time after the stapler motor
/Rr (M17) turns ON.
SD J-7284 The clincher motor /Fr does not return
to the home position within a speci-
fied period of time after the clincher
motor /Fr turns ON.
J-7285 The clincher motor /Rr does not
return to the home position within a
specified period of time after the
clincher motor /Rr turns ON.
MT J-7290 The conveyance sensor /Up (PS9) or
/Lw (PS10) of MT does not turn ON
within a specified period of time after
the conveyance sensor (PS5) of FS
turns ON.
The conveyance sensor /Up (PS9) or
/Lw (PS10) do not turn OFF within a
specified period of time after PS9 or
PS10 turn ON.
317
12. JAM CODE Field Service Ver.2.0 Jan. 2007
operation
Paper J-8100 The registration sensor (PS1) turns The printer sec- Open the vertical con-
When idling
feed ON while in idling. tion stops veyance door and ADU
J-8200 The vertical conveyance sensor (PS2) immediately. and remove jammed
turns ON while in idling. paper if any.
PC-202 J-8300 The vertical conveyance sensor /3 Open the right door
(PS116) turns ON while in idling. and remove jammed
PC-402 The vertical conveyance sensor (PS2) paper if any.
turns ON while in idling.
PC-202 J-8400 The vertical conveyance sensor /4
(PS126) turns ON while in idling.
LU J-8500 The LU exit sensor (PS155) turns ON Open the upper door
while in idling. and remove jammed
paper if any.
Fusing J-9000 The fusing exit sensor (PS3) turns ON Open ADU and remove
while in idling. jammed paper if any.
Reverse J-9100 The reverse sensor (PS27) turns ON
while in idling.
ADU J-9200 The ADU conveyance sensor /1
(PS24) turns ON while in idling.
J-9300 The ADU conveyance sensor /2
(PS25) turns ON while in idling.
J-9701 The ADU conveyance sensor /1
During operation
318
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
13.1 Malfunction code list
A. Note for use
Turn OFF/ON the power switch (SW2) of the main body when releasing an abnormal condition.
B. Code list
NOTE
• For codes with "*" given in the error code column, a message "Turn off the power and turn it on
again" is displayed on the operation panel.
• For codes with no "*" given in the error code column, a message "Contact the service" is dis-
played.
does not turn ON within a speci- stops immedi- Upper limit sensor /1 (PS6)
fied period of time after the paper ately to turn OFF Printer control board (PRCB)
lift motor /1 (M7) turns ON. the main relay
C-0202 The upper limit sensor /2 (PS13) (RL1). Paper lift motor /2 (M8)
does not turn ON within a speci- Upper limit sensor /2 (PS13)
fied period of time after the paper Printer control board (PRCB)
lift motor /2 (M8) turns ON.
C-0203 The upper limit sensor /3 (PS114) Paper lift motor /3 (M124)
PC-202
319
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Drive C-0207 While in the paper feed, there The main body Pick-up solenoid /BP (SD1)
Bypass
320
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
FS-511 C-1102 Tray lift motor (M7) drive abnor- The main body Tray lift motor (M7)
FS
321
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
FS-511 C-1105 Intermediate conveyance roller The main body Intermediate conveyance
FS
release motor (M12) drive abnor- stops immedi- roller release motor (M12)
mality. ately to turn OFF Roller release home sensor
• When starting the pressure the main relay (PS12)
position drive, the roller (RL1). FS control board (FSCB)
release home sensor (PS12)
does not turn ON within a
specified period of time after
M12 turns ON.
• When starting the separation
position drive, PS12 does not
turn OFF within a specified
period of time after M12 turns
ON.
C-1106 Stapler movement motor (M6) Stapler movement motor
drive abnormality. (M6)
• While in the home position Stapler home sensor (PS14)
search, the stapler home sen- FS control board (FSCB)
sor (PS14) does not turn ON
within a specified period of
time after M6 turns ON.
• While in the 1-staple position
movement, PS14 does not
turn OFF within a specified
period of time after M6 turns
ON.
C-1107 Stapler motor /Rr (M16) drive Stapler motor /Rr (M16)
abnormality. Stapler home sensor /Rr
• The stapler home sensor /Rr (PS22)
(PS22) does not turn OFF FS control board (FSCB)
within a specified period of
time after M16 turns ON.
• PS22 does not turn ON within
a specified period of time
after the OFF of PS22 is
detected.
• PS22 does not turn ON within
a specified period of time
after M16 turns ON for
reverse rotation.
322
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
FS-511 C-1108 Stapler motor /Fr (M17) drive The main body Stapler motor /Fr (M17)
FS
323
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
SD C-1110 Saddle stapler motor /Rr drive The main body Saddle stapler motor /Rr
FS
324
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
SD C-1113 Exit open/close motor (M9) drive The main body Exit open/close motor (M9)
FS
325
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
FS-510 C-1117 Alignment motor /Fr (M5) drive The main body Alignment motor /Fr (M5)
FS
326
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
PU C-1121 Punch motor (M1) drive abnor- The main body Punch motor (M1)
FS
process between the engine control of the Printer control board (PRCB)
commu- overall control board (OACB) and
nication that of the printer control board
abnor- (PRCB)
mality While in the stand-by, a process
Ready signal cannot be detected
for a specified period of time.
Motor C-2201 Developing motor (M3) speed Developing motor (M3)
speed abnormality. Printer control board (PRCB)
abnor- While M3 is ON, an EM error sig-
mality nal has been detected 5 times in
succession within a specified
period of time.
C-2202 Drum motor (M1) speed abnor- Drum motor (M1)
mality. Printer control board (PRCB)
While M1 is ON, an EM error sig-
nal has been detected 5 times in
succession within a specified
period of time.
Fan C-2301 Drum cooling fan (FM4) abnor- Drum cooling fan (FM4)
lock mality. Printer control board (PRCB)
abnor- While FM4 is ON, an EM error
mality signal has been detected 5 times
in succession within a specified
period of time.
C-2302 Developing suction fan motor Developing suction fan
(FM6) abnormality. motor (FM6)
While FM6 is ON, an EM error Printer control board (PRCB)
signal has been detected 5 times
in succession within a specified
period of time.
C-2303 Developing cooling fan (FM7) Developing cooling fan (FM7)
abnormality. Printer control board (PRCB)
While FM7 is ON, an EM error
signal has been detected 5 times
in succession within a specified
period of time.
327
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Abnor- C-2401 High machine inside temperature The main body TCR sensor (TCRS)
Main body
328
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
High C-2803 TCR output abnormality. The main body TCR sensor (TCRS)
Main body
voltage When the output ripple voltage of stops immedi- Printer control board (PRCB)
power the TCR sensor (TCRS) is less ately to turn OFF
source than 0.5 V. the main relay
abnor- C-2804 Toner density abnormality. (RL1). Toner remaining sensor
mality When the L detection output is in (PZS)
excess of 2.6 V before the toner TCR sensor (TCRS)
remaining sensor (PZS) detects a Printer control board (PRCB)
no toner condition, toner density
does not recover even when
toner is automatically supplied.
Motor C-3201 Fusing motor (M11) speed abnor- Fusing motor (M11)
speed mality. Printer control board (PRCB)
abnor- When M11 is ON, an EM error
mality signal is detected 30 times in
succession within a specified
period of time.
Fan C-3301 Fusing cooling fan /Fr (FM2) Fusing cooling fan /Fr (FM2)
lock abnormality. Printer control board (PRCB)
abnor- When FM2 is ON, an EM error
mality signal is detected 3 times in suc-
cession within a specified period
of time.
C-3302 Fusing cooling fan /Rr (FM8) Fusing cooling fan /Rr (FM8)
abnormality. Printer control board (PRCB)
When FM8 is ON, an EM error
signal is detected 3 times in suc-
cession within a specified period
of time.
Fusing C-3501 Fusing main sensor high temper- The main body Thermistor /1 (TH1)
high ature abnormality. stops immedi- Printer control board (PRCB)
temper- The thermistor /1 (TH1) detects a ately to turn OFF
ature temperature higher than 236 °C the main relay
abnor- for more than a specified period (RL1). All the
mality of time. keys are not
C-3502 Fusing sub sensor high tempera- taken in. Thermistor /2 (TH2)
ture abnormality. Printer control board (PRCB)
The thermistor /2 (TH2) detects a
temperature higher than 236 °C
for more than a specified period
of time.
329
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Fusing C-3801 Fusing main sensor low tempera- The main body Thermistor /1 (TH1)
Main body
330
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
Fusing C-3808 Fusing sub sensor high tempera- The main body Thermistor /2 (TH2)
Main body
low ture abnormality (sub CPU detec- stops immedi- Printer control board (PRCB)
temper- tion) ately to turn OFF
ature In the sub CPU, the thermistor /2 the main relay
abnor- (TH2) detects a temperature (RL1). All the
mality higher than 236 °C for more than keys are not
a specified period of time. taken in.
Fusing C-3901 Inferior contact of the thermistor Thermistor /1 (TH1)
sensor /1 (TH1) Printer control board (PRCB)
abnor- While in the warm-up condition,
mality when the thermistor /2 (TH2)
detection temperature gets to the
Ready temperature before the
TH1 detection temperature, the
TH1 detection temperature does
not get to the Ready temperature
a specified period of time after
the TH2 detection temperature
got to the Ready temperature.
C-3902 Inferior contact of the thermistor Thermistor /2 (TH2)
/2 (TH2) Printer control board (PRCB)
While in the warm-up condition,
when the thermistor /1 (TH1)
detection temperature gets to the
Ready temperature before the
TH2 detection temperature, the
TH2 detection temperature does
not get to the Ready temperature
a specified period of time after
the TH1 detection temperature
got to the Ready temperature.
C-3903 Thermistor /1 (TH1) open abnor- Thermistor /1 (TH1)
mality (sub CPU detection) Printer control board (PRCB)
In the sub CPU, the TH1 detec-
tion temperature detects a tem-
perature between -8 and 20 °C
for more than a specified period
of time.
C-3904 Thermistor /2 (TH2) open abnor- Thermistor /2 (TH2)
mality (sub CPU detection) Printer control board (PRCB)
In the sub CPU, the TH2 detec-
tion temperature detects a tem-
perature between -8 and 20 °C
for more than a specified period
of time.
331
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Image C-4001 Index board (INDEXB) contact The main body Index board (INDEXB)
Main body
332
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
Fan C-5301 Exhaust fan /Fr (FM3) conversion The main body Exhaust fan /Fr (FM3)
Main body
333
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Scanner C-6101 While in the exposure unit initial Scanner sec- Scanner motor (M2)
Main body
abnor- search, the scanner home sensor tion stops Scanner home sensor
mality (PS30) does not turn on within a immediately. (PS30)
specified period of time. And Printer control board (PRCB)
also, while in the return scan,
PS30 does not turn on within a
specified period of time.
C-6201 Exposure lamp (L1) abnormality. Exposure lamp (L1)
A specified period of time after L1 L1 inverter (L1 INVVB)
turns on, an L1 abnormality signal Printer control board (PRCB)
is detected in succession for a
specified period of time.
Image C-6701 AOC abnormality. CCD board (CCDB)
proces- AOC counter overflow Exposure lamp (L1)
sing C-6702 AGC abnormality. L1 inverter (L1 INVVB)
abnor- AGC counter overflow Scanner motor (M2)
mality Overall control board (OACB)
Commu- C-8001 DF control board (DFCB) commu- The main body DF control board (DFCB)
DF
334
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
FAX C-B117 Time out error for ACK standby FAX breakdown FK-502
FAX
335
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Line C-B150 External class instance acquisi- FAX breakdown FK-502
FAX
336
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
Page C-B185 Incoming data size logic error FAX breakdown FK-502
FAX
337
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
Fan C-D201 Overall control board cooling fan The main body Overall control board (OACB)
Main body
338 1
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
System C-E085* Copy sequence abnormality. Engine section Overall control board (OACB)
Main body
339
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
System C-E08E* Unrecoverable error (The count is Engine section Overall control board (OACB)
Main body
340
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
System C-E097* Unrecoverable error (The count is Engine section Overall control board (OACB)
Main body
341
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
operation
System C-E0A1* Unrecoverable error (The count is Engine section Overall control board (OACB)
Main body
342
Field Service Ver.2.0 Jan. 2007 13. MALFUNCTION CODE
bizhub 500/420/360
operation
System C-E0AA* Unrecoverable error (The count is Engine section Overall control board (OACB)
Main body
343
13. MALFUNCTION CODE Field Service Ver.2.0 Jan. 2007
For setting of DipSW that is specified for the following items, it is possible to use them with a failed section sep-
arated. After setting DipSW, however, no abnormality detection is made on the separated section.
NOTE
• This function is employed to make temporary use of sections that are not affected. So, be sure
that this is limited only to a provisional use until a defective section is repaired.
344
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
APPENDIX
bizhub 500/420/360
14. PARTS LAYOUT DRAWING
14.1 Main body
14.1.1 Switch/sensor
A. Main body rear side
[4]
50gaf5c017na
345
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
[1]
[3]
[2]
50gaf5c018na
[2]
50gaf5c019na
346
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
D. Developing section
bizhub 500/420/360
[1]
50gaf5c020na
[2]
[4]
[3] 50gaf5c034na
[1] Upper limit sensor /1 (PS6) [4] Paper size sensor /Rr1 (PS10)
[2] Paper empty sensor /1 (PS5) [5] Tray set sensor /1 (PS8)
[3] Paper size sensor /Fr1 (PS11) [6] Near-empty sensor /1 (PS9)
347
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
(2) Tray 2
bizhub 500/420/360
[2]
[3]
[6] [4]
[5] 50gaf5c035na
[1] Vertical conveyance sensor (PS2) [5] Paper size sensor /Fr2 (PS17)
[2] Feed door open/close sensor (PS7) [6] Paper size sensor /Rr2 (PS16)
[3] Paper empty sensor /2 (PS12) [7] Tray set sensor /2 (PS14)
[4] Upper limit sensor /2 (PS13) [8] Near-empty sensor /2 (PS15)
(3) Registration
[1] 50gaf5c036na
348
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
bizhub 500/420/360
[6] [7] [1] [2]
[1] Paper size VR/BP (VR1) [5] Paper size sensor /BP4 (PS22)
[2] Paper empty sensor /BP (PS18) [6] Paper size sensor /BP2 (PS20)
[3] Lift sensor (PS23) [7] Paper size sensor /BP1 (PS19)
[4] Paper size sensor /BP3 (PS21)
G. ADU section
[1]
[2]
[3]
50gaf5c038na
[1] ADU open/close sensor (PS26) [3] ADU conveyance sensor /2 (PS25)
[2] ADU conveyance sensor /1 (PS24)
349
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
H. Fusing section
bizhub 500/420/360
[1] [4]
[3] [2]
50gaf5c021na
[1]
50gaf5c039na
350
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
14.1.2 Load
bizhub 500/420/360
A. Main body rear side
[11]
[10]
[9] [1]
[2]
[7]
[3]
[6] [5] [4] [8]
50gaf5c022na
351
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
[4]
[1]
[2]
[3]
50gaf5c023na
[1] Fusing cooling fan /Rr (FM8) [3] Drum cooling fan (FM4)
[2] Fusing cooling fan /Fr (FM2) [4] Developing suction fan (FM6)
[1]
[2]
50gaf5c024na
352
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
D. Write section
bizhub 500/420/360
[1]
50gaf5c025na
[1]
50gaf5c026na
353
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
(1) Tray 1
[2] [1]
50gaf5c040na
(2) Tray 2
[3] [1]
[2] 50gaf5c041na
[1] Vertical conveyance clutch (CL3) [3] Paper lift motor /2 (M8)
[2] Feed clutch /2 (CL5)
354
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
(3) Registration
bizhub 500/420/360
[1]
[2]
50gaf5c042na
[1]
[2] 50gaf5c043na
[1] Feed clutch /BP (CL6) [2] Pick-up solenoid /BP (SD1)
355
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
H. ADU section
bizhub 500/420/360
[1]
[2]
50gaf5c044na
[1] ADU conveyance clutch /Up (CL7) [2] ADU conveyance clutch /Lw (CL8)
[1]
[4] [3] [2] 50gaf5c045na
356
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
bizhub 500/420/360
A. Main body rear side
[1]
[2]
[9]
[3]
[8]
[7]
[4]
[6]
[5]
50gaf5c027na
357
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
[1]
50gaf5c028na
[1]
[2]
50gaf5c029na
358
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
bizhub 500/420/360
[8]
[7]
[6]
[1]
[5]
[4]
[2]
[3]
50gaf5c030na
E. Write section
[2]
[1]
50gaf5c031na
359
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
[2]
[1]
50gaf5c032na
G. ADU section
[1]
50gaf5c046na
360
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
H. Fusing section
bizhub 500/420/360
[2]
[1]
50gaf5c033na
[1] Fusing heater lamp /2 (L3) [2] Fusing heater lamp /1 (L2)
361
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.2 DF
bizhub 500/420/360
A. Front side
[1]
[2]
16eaf5c001na
[1] Pressure roller release solenoid (SD1) [2] LED board (LB)
B. Rear side
[5]
[1]
[4] [2]
[3]
16eaf5c002na
362
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
C. Upper surface
bizhub 500/420/360
[7] [8] [9] [10] [11]
[1] Original size sensor /2 (PS2) [7] Original empty sensor (PS5)
[2] Stamp solenoid (SD2) [8] Original registration sensor (PS9)
[3] Original exit sensor (PS10) [9] Original size sensor /1 (PS1)
[4] Original detection sensor (PS8) [10] Original size sensor /3 (PS3)
[5] Original feed sensor (PS6) [11] Original size sensor /4 (PS4)
[6] Mix original size detection board (MOSDB)
[1]
[2]
16eaf5c004na
363
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.3 PC
bizhub 500/420/360
14.3.1 PC-202
[21]
[20]
[19] [22]
[18] [23]
[17] [24]
[16] [25]
[15] [26]
[14]
[1]
[13]
[12]
[2]
[11]
[3]
[10]
[9] [4]
[8]
[5]
[7]
[6]
4061f5c001na
[1] Vertical conveyance sensor /4 (PS126) [14] Paper size detect board /3 (PSDB3)
[2] Paper feed sensor /4 (PS125) [15] Paper size sensor /Rr3 (PS118)
[3] Paper empty sensor /4 (PS124) [16] Paper size sensor /Fr3 (PS119)
[4] Upper limit sensor /4 (PS123) [17] Tray set sensor /3 (PS112)
[5] Vertical conveyance motor /4 (M121) [18] Near-empty sensor /3 (PS113)
[6] Paper feed motor /4 (M123) [19] Paper lift motor /3 (M124)
[7] Paper lift motor /4 (M125) [20] Paper feed motor /3 (M122)
[8] Near-empty sensor /4 (PS122) [21] Vertical conveyance motor /3 (M120)
[9] Paper size sensor /Fr4 (PS128) [22] Right door open/close sensor (PS111)
[10] Paper size sensor /Rr4 (PS127) [23] Upper limit sensor /3 (PS114)
[11] Paper size detect board /4 (PSDB4) [24] Vertical conveyance sensor /3 (PS117)
[12] Tray set sensor /4 (PS121) [25] Paper feed sensor /3 (PS116)
[13] PC control board (PCCB) [26] Paper empty sensor /3 (PS115)
364
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
14.3.2 PC-402
bizhub 500/420/360
[20]
[19] [21]
[18]
[17]
[22]
[16]
[23]
[24]
[1]
[15]
[2]
[3]
[14]
[4]
[5]
[13]
[6]
[7]
[8]
[12] [9]
[11] [10]
4061f5c201na
[1] Paper empty sensor (PS3) [13] Shift gate motor (M3)
[2] Main tray empty board (MEB) [14] Shift gate position sensor (PS14)
[3] Paper lift motor (M5) [15] Rely board (RLB)
[4] Paper lift motor encoder sensor (PS10) [16] PC control board (PCCB)
[5] Lower limit over run sensor (PS7) [17] Tray lock solenoid (SD1)
[6] Shft motor encoder sensor (PS8) [18] Tray set sensor (PS6)
[7] Shift motor (M4) [19] Paper feed motor (M1)
[8] Tray release switch (SW1) [20] Vertical conveyance motor (M2)
[9] Shift position sensor (PS11) [21] Right door open/close sensor (PS5)
[10] Lower limit sensor (PS13) [22] Vertical conveyance sensor (PS2)
[11] Sub tray empty sensor (PS9) [23] Upper limit sensor (PS4)
[12] Shift home sensor (PS12) [24] Paper feed sensor (PS1)
365
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.4 LU
bizhub 500/420/360
[5]
[1]
[2]
[4] [3]
[9]
16aaf5c001na
[1] Remaining paper sensor /1 (PS154) [7] Upper limit sensor (PS152)
[2] Remaining paper sensor /2 (PS151) [8] Feed clutch (CL151)
[3] Dehumidifier heater (HTR101) [9] LU set sensor (PS156)
(Service parts setting
P/N 56AA-710# ) [10] Paper lift motor (M151)
[4] Pick-up solenoid (SD151) [11] Feed motor (M150)
[5] Paper empty sensor (PS153) [12] LU drive board (LUDB)
[6] LU exit sensor (PS155) [13] Upper door interlock switch (MS151)
366
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
14.5 FS
bizhub 500/420/360
14.5.1 FS-510
[27]
[26]
[28]
[20] [25]
[24] [29]
[21]
[23] [30]
[1]
[19] [22]
[18]
[17]
[16]
[2]
[13]
[12] [3]
[11] [4]
[10] [5]
[15] [9] [6]
[7]
[14]
[8]
4349f5c001na
367
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.5.2 FS-511
bizhub 500/420/360
A. Front side
[1]
[2]
[4]
[3] 4521f5c001na
[1] Main gate solenoid (SD2) [3] Tray lift motor (M7)
[2] Front door sensor (PS17) [4] Main tray upper limit LED (LED19)
368
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
B. Rear side
bizhub 500/420/360
[10] [11] [12] [13] [14]
[1]
[9]
[2]
[8] [3]
[7] [4]
[6]
[5]
4521f5c002na
[1] Main tray lower limit switch (SW3) [8] Bypass gate solenoid (SD1)
[2] Main tray upper limit sensor (PS19) [9] Entrance conveyance motor (M1)
[3] Paddle motor /Up (M15) [10] Conveyance motor /Up (M4)
[4] Paper exit motor (M3) [11] Conveyance motor /Lw (M2)
[5] FS control board (FSCB) [12] Paper exit roller release motor (M13)
[6] Interlock switch (SW1) [13] Main tray full sensor (PS7)
[7] Intermediate conveyance roller release [14] Paddle solenoid /Up (SD3)
motor (M12)
369
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
C. Punch section
bizhub 500/420/360
[3] [1]
[2] 4521f5c003na
370
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
D. Conveyance section
bizhub 500/420/360
[13]
[12] [14]
[15]
[16]
[11]
[1]
[10]
[2]
[9] [3]
[4]
[8]
[5]
[6]
[7]
4521f5e001na
[1] Hole punch position switch (SW4) [9] Paddle motor /Lw (M9)
[2] Hole punch selector motor (M14) [10] Roller release home sensor (PS12)
[3] Intermediate conveyance sensor (PS3) [11] Main route conveyance sensor (PS4)
[4] Alignment tray sensor (PS5) [12] Exit roller home sensor (PS13)
[5] Main tray reset sensor (PS8) [13] Upper door sensor (PS18)
[6] Alignment home sensor (PS9) [14] Sub tray full sensor (PS6)
[7] Main tray upper limit switch (SW2) [15] Sub tray exit sensor (PS1)
[8] Alignment motor (M5) [16] Bypass route conveyance sensor (PS2)
371
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
E. Stapler section
bizhub 500/420/360
[1]
[2]
4521f5c005na
[1] Stapler home sensor (PS14) [2] Stapler moving motor (M6)
372
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
bizhub 500/420/360
[3] [1]
[2]
4521f5c006na
373
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.6 PU-501
bizhub 500/420/360
[1]
[2]
[3]
[5]
[4]
4512f5c001na
[1] Punch scraps full sensor (PS1) [4] Encoder sensor (PS4)
[2] Punch position sensor /1 (PS2) [5] Punch motor (M1)
[3] Punch position sensor /2 (PS3)
374
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
14.7 SD-502
bizhub 500/420/360
[14]
[1]
[13]
[12]
[11]
[10]
[9]
[8]
[2]
[7]
[3]
[6]
[5] [4]
4511f5c001na
375
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.8 MT-501
bizhub 500/420/360
[11] [12]
[13]
[10] [14]
[15]
[16]
[9] [1]
[2]
[3]
[8]
[7]
[6]
[4]
[5]
4510f5c001na
376
Field Service Ver.2.0 Jan. 2007 14. PARTS LAYOUT DRAWING
14.9 RU-502
bizhub 500/420/360
[2] [1]
16faf5c001na
377
14. PARTS LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
14.10 JS-502
bizhub 500/420/360
[1]
[2]
4347f5c001na
378
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
bizhub 500/420/360
15.1 Main body
15.1.1 Connector in the board
A. Overall control board
59 (W : 24 pin)
NC
803 (BN : 6 pin)
1000 (BN : 8 pin) NC
NC 500 (BK : 44 pin)
NC 804 (BK : 20 pin)
45 (Silver Metal : 4 pin) 55 (BK : 100 pin)
379
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
37 (W : 8 pin) 36 (W : 10 pin)
38 (BN : 20 pin)
91 (BN : 2 pin)
21 (W : 11 pin)
NC NC
35 (W : 5 pin) NC
NC
18 (BN : 12 pin)
20 (W : 6 pin)
90 (W : 8 pin)
69 (BN : 3 pin)
17 (BN : 10 pin)
11 (W : 3 pin)
26 (W : 13 pin) 23 (W : 12 pin) 39 (W : 5 pin)
12 (BK : 68 pin)
380
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
bizhub 500/420/360
62 (BK : 3 pin)
63 (W : 10 pin)
65 (W : 2 pin)
D. CCD board
60 (BN : 50 pin)
50gaf5c004na
381
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
E. DC power supply
bizhub 500/420/360
10 (W : 2 pin)
9 (W : 3 pin)
382
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
bizhub 500/420/360
71 (W : 11 pin)
70 (W : 6 pin)
72 (W : 3 pin)
50gaf5c006na
G. Index board
51 (BN : 5 pin)
50gaf5c007na
383
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
H. L1 inverter
bizhub 500/420/360
I. L1 relay board
50gaf5c009na
K. Operation board
2 (W : 3 pin)
56 (BK : 22 pin) 1 (BN : 28 pin)
7 (NC)
3 (BN : 4 pin)
4 (BK : 17 pin)
50gaf5c011na
384
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
L. OB inverter
bizhub 500/420/360
8 (BN : 3 pin) 9 (W : 4 pin)
50gaf5c012na
M. NVRAM board
1 (BN : 20 pin)
6 (BK : 22 pin)
50gaf5c014na
385
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
87,88 (W : 5 pin)
50gaf5c015na
1 (W: 7 pin)
50gaf5c016na
386
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
15.2 DF
bizhub 500/420/360
15.2.1 Connector in the board
A. DF control board (DFCB)
1 (W : 2 pin) 11 (W : 2 pin)
3 (W : 4 pin) 4 (W : 7 pin)
13 (W : N.C.)
2 (W : 13 pin)
6 (W : 12 pin)
5 (W : 11 pin)
16eaf5c005na
3 (W : 3 pin) 2 (W : 12 pin)
1 (W : 7 pin)
16eaf5c006na
1 (W : 4 pin)
16eaf5c007na
387
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
15.3 PC
bizhub 500/420/360
5 (W : 8 pin) 3 (W : 14 pin)
6 (W : 15 pin) 4 (W : 5 pin)
1 (W : 12 pin)
8 (W : 13 pin)
2 (W : 2 pin)
7 (W : 7 pin)
4061f5c002na
1 (W : 5 pin)
4061f5c003na
388
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
B. PC-402
bizhub 500/420/360
(1) PC control board (PCCB)
3 (W : 11 pin) 5 (W : 15 pin)
1 (W : 12 pin)
2 (W : 2 pin)
N.C
4061f5c202na
1 (W : 22 pin) 2 (W : 22 pin)
4061f5c203na
1 (W : 3 pin)
4061f5c204na
389
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
15.4 LU
bizhub 500/420/360
112 (W : 12 pin)
114 (W : 4 pin)
113 (GY : 22 pin)
111 (W : 2 pin)
390
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
15.5 FS
bizhub 500/420/360
15.5.1 Connector in the board
A. FS-510
(1) FS control board (FSCB)
8 (W : 2 pin)
10 (W : 3 pin)
2 (W : 8 pin)
11 (W : 6 pin)
9 (W : 7 pin)
14 (W : 9 pin)
26 (W : 2 pin)
13 (W : 10 pin)
25 (W : 5 pin)
17 (W : 7 pin) 19 (W : 4 pin)
4349f5c002na
2 (W : 15 pin)
1 (W : 7 pin)
4349f5c003na
391
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
B. FS-511
bizhub 500/420/360
6 (W : 2 pin)
5 (W : 4 pin)
4 (W : 2 pin)
15 (W : 8 pin)
3 (W : 2 pin)
16 (W : 6 pin)
2 (W : 2 pin)
17 (W : N.C.)
1 (W : 6 pin)
18 (W : 12 pin)
22 (W : 3 pin) 19 (W : 15 pin)
24 (W : 7 pin) 20 (W : 9 pin)
25 (W : 15 pin) 23 (W : 7 pin) 21 (W : 4 pin)
4521f5c007na
392
Field Service Ver.2.0 Jan. 2007 15. CONNECTOR LAYOUT DRAWING
15.6 SD
bizhub 500/420/360
15.6.1 Connector in the board
A. SD control board (SDCB)
7 (W : 8 pin)
4 (W : 9 pin)
393
15. CONNECTOR LAYOUT DRAWING Field Service Ver.2.0 Jan. 2007
15.7 MT
bizhub 500/420/360
102 (W : 12 pin)
103 (W : 7 pin)
107 (W : 8 pin)
104 (W : 2 pin)
4510f5c002na
394
16.1 Main body
Field Service Ver.2.0 Jan. 2007
Start key ON
A. A4, 2 single sided originals, single sided copy (1 copy), paper feed tray 1
50gaf5c047na
16. TIMING CHART
395
bizhub 500/420/360
bizhub 500/420/360
396
16. TIMING CHART
Start key ON
50gaf5c048na
Field Service Ver.2.0 Jan. 2007
Start key ON / 1st sheet feed start 2nd sheet feed start 2nd sheet scan start
16.2 DF
Original set 1st sheet scan start 1st sheet scan complete 2nd sheet scan complete
OFF
Original registration sensor ON
(PS9)
OFF
Original detection sensor ON
(PS8)
OFF
Original exit sensor (PS10)
ON
OFF
Pressure roller release ON
solenoid (SD1)
OFF
ON
Stamp solenoid (SD2)
A. Single sided original mode (A4, 2 sheets feed)
OFF
ON
DSET signal
OFF
ON
VD signal
OFF
ON
NEXTPAGE signal
OFF
High speed
Low speed
Original feed
motor (M1) Stop
Middle speed
High speed
Low speed
Original conveyance
Stop
motor (M2)
Low speed
High speed
16eaf5c009na
16. TIMING CHART
397
bizhub 500/420/360
bizhub 500/420/360
398
16. TIMING CHART
OFF
DSET signal
ON
OFF
VD signal ON
OFF
NEXTPAGE signal
ON
OFF
High speed
Original feed Low speed
motor (M1) Stop
Middle speed
High speed
Original Low speed
conveyance Stop
motor (M2) Low speed
High speed
16eaf5c010na
Field Service Ver.2.0 Jan. 2007
2nd sheet front face scan complete Reverse complete 2nd sheet back face scan complete Reverse complete 2nd sheet exit complete
2nd sheet front face scan start Reverse start Reverse start 2nd sheet exit start
2nd sheet back face scan start
Original empty sensor ON
(PS5) OFF
Original feed sensor ON
(PS6)
Field Service Ver.2.0 Jan. 2007
OFF
Original registration ON
sensor (PS9) OFF
Original detection ON
sensor (PS8) OFF
Original exit sensor ON
(PS10) OFF
Pressure roller release ON
solenoid (SD1)
OFF
High speed
Original Low speed
conveyance Stop
motor (M2) Low speed
High speed
16eaf5c011na
16. TIMING CHART
399
bizhub 500/420/360
bizhub 500/420/360
400
Start key ON / 1st sheet feed start 2nd sheet feed start 2nd sheet scan start
Original set 1st sheet scan start 1st sheet scan complete 2nd sheet scan complete
16. TIMING CHART
High speed
Low speed
Original conveyance
Stop
motor (M2)
Low speed
High speed
Stamp operation is executed only when "trailing edge" or "leading edge and trailing edge" specified.
16eaf5c012na
Field Service Ver.2.0 Jan. 2007
Start key ON / 1st sheet feed start Command received / 2nd sheet feed start 2nd sheet scan complete Command received
Original set 1st sheet scan start 1st sheet scan complete 2nd sheet scan start
Original registration ON
sensor (PS9)
OFF
Original detection ON
sensor (PS8)
OFF
ON
Original exit sensor (PS10)
OFF
Pressure roller release ON
solenoid (SD1)
OFF
Stamp solenoid (SD2)
ON
OFF
D. FAX immediate send mode (A4, 2 sheets feed)
ON
DSET signal
OFF
ON
VD signal
OFF
ON
NEXTPAGE signal
OFF
High speed
High speed
Low speed
Original conveyance Stop
motor (M2)
Low speed
High speed
Stamp operation is executed only when "trailing edge" or "leading edge and trailing edge" specified.
When the communication completes normally, the trailing edge is stamped on.
16eaf5c013na
16. TIMING CHART
401
bizhub 500/420/360
bizhub 500/420/360
402
16.3 LU
16. TIMING CHART
Start key ON
16aaf5c003na
Field Service Ver.2.0 Jan. 2007
16.4.1
16.4 FS
FS-510
Field Service Ver.2.0 Jan. 2007
ON
Conveyance sensor (PS5)
OFF
Forward
Entrance motor (M3)
Stop
High speed
Conveyance motor Low speed
(M2)
Stop
Forward
Exit motor (M1)
Stop
4349f5c004na
16. TIMING CHART
403
bizhub 500/420/360
bizhub 500/420/360
404
16. TIMING CHART
ON
Stacker sensor (PS8)
OFF
Forward
Entrance motor (M3)
Stop
High speed
Conveyance
Low speed
motor (M2)
Stop
Forward
Exit motor (M1) Stop
Reverse
ON
Registration clutch (CL1)
OFF
Forward
Punch motor (M1)
Reverse
release Stop
motor (M6) Reverse (pressure)
Stacker paddle ON
solenoid (SD1) OFF
Forward
Alignment motor Stop
/Rr (M4)
Reverse
Forward
Alignment motor /Fr Stop
(M5)
Reverse
Stapler movement Forward
motor (M7) Stop
Forward
Stapler motor
Stop
4349f5c005na
Field Service Ver.2.0 Jan. 2007
16.4.2
FS-511
Field Service Ver.2.0 Jan. 2007
Entrance conveyance ON
motor (M1) OFF
ON
Conveyance motor /Up (M4)
OFF
ON
Main gate solenoid (SD2) OFF
4521f5c008na
16. TIMING CHART
405
bizhub 500/420/360
bizhub 500/420/360
406
16. TIMING CHART
Item
Fusing exit sensor (PS3) L
H 1 2 1 2
Entrance conveyance ON
motor (M1) OFF
Intermediate conveyance L 1 2 1 2
sensor (PS3) H
H Shift position
Shift home sensor (PS10)
L
Forward
Paper exit motor (M3) Stop
Reverse
4521f5c009na
Field Service Ver.2.0 Jan. 2007
FS operation start signal ON
Item
Fusing exit sensor (PS3) L
H 1 2 1 2
Entrance conveyance ON
motor (M1) OFF
Field Service Ver.2.0 Jan. 2007
Intermediate conveyance L 1 2 1 2
sensor (PS3) H
Alignment operation Alignment operation
Forward
Alignment motor (M5) Stop
C. 1 staple /Rr, A4S, 2 originals, 2 copies setting
Reverse
4521f5c010na
16. TIMING CHART
407
bizhub 500/420/360
bizhub 500/420/360
408
16. TIMING CHART
L
Fusing exit sensor (PS3)
H
Entrance conveyance ON
motor (M1) OFF
ON
D. Non-sort, punch, 1 original, 1copy setting
4521f5c011na
Field Service Ver.2.0 Jan. 2007
Field Service Ver.2.0 Jan. 2007 17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17.1 Main body 1/4
1 2 3 4 5 6 7 8 9 10 11 12 13
A RL24V
A
RL1 POWER RL1 CNT FT20 FT21 FT22
J21-01
J13-2
Circuit breaker /1 CN9-1 AC(H)
FT23
FT24
TS
FT3 FT5 CN10-1 AC(H) BT1 Main relay Thermostat
CBR 1 AC(H)
AC DRIVE
B RL1
CR001
FT26
Fusing heater lamp /1
B
Noise filter
FT1 J21-02 J13-3
CN9-2 L2 DRIVE FT25
L2
Inlet
NF
Plug RL1 POWER RL1 CNT
CR002 Fusing heater lamp /2
FT2 J13-4 FT28
Circuit breaker /2 J21-03
L3
CN9-3 L3 DRIVE FT27
FT4 FT6 CN10-2 AC(N) BT3 Sub relay
CBR 2 AC(N)
RL2 J13-1
C CN8-1 SW IN(H)
CR003
RT4
Ǿ4
RT3
Ǿ4
C
CN8-3 SW IN(N)
EN5V2 2-5
EN12V1 2-4
DCPS(1/2) NMI
12V1
S.GND
2-3
2-2
2-1
E 5V2 4-1
E
for FNS
24V 5V2 4-2
S.GND 4-3
F3 11 5-1 24V
S.GND 4-4
12 5-2 24V
F1 12V2 4-5
13 5-3 24V
S.GND 4-6
14 5-4 P.GND
F2 S.GND 4-7
15 5-5 P.GND
12V2 4-8
16 5-6 P.GND
F 17 5-7 S.GND Interlock switch
MS F
6-8 P.GND
6-7 P.GND
6-5 P.GND
6-6 P.GND
18 5-8 S.GND
SWD24V
6-4 24V
6-3 24V
6-1 24V
19 5-9 5V2
12V2(LD) 42- 8
S.GND 42- 7
S.GND 42- 6
12V2 42- 5
S.GND 42- 4
S.GND 42- 3
42- 2
42- 1
41- 5
41- 4
41- 3
41- 2
41- 1
40- 4
40- 3
40- 2
40- 1
6-2 24V
24V 7-1 5
20 5-10 5V2 J23-1 J24-1A -1B J23-3
SWD24V
24V 7-2 6
EN12V1
S.GND
EN5V2
S.GND
S.GND
12V1
/NMI
J23-2 J24-2A J24-2B J23-4
5V2
5V2
5V1
5V1
(J23:NMF)
G 63 64 3 4 1 2
G
ENPWR 31- 1
12V2(LD) 42- 9
S.GND 500- 4
S.GND 500- 3
S.GND 42- 8
S.GND 42- 6
S.GND 42- 4
S.GND 42- 3
S.GND 31- 6
EN24V 31- 3
EN5V2 31- 2
for for for
12V2 42- 5
12V1 31- 5
5V1 500- 2
5V1 500- 1
-12V 42- 7
-12V 31- 7
31- 4
42- 2
42- 1
LU DF SDB
3-1
NMI
5V2
5V2
-3 80-A13 34-A2 S.GND
-4 80-A12 34-A3 DB1
H 80-A11
80-A10
80- A9
34-A4 XSCL
34-A5 S.GND
34-A6 YD
H
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 32
4-17
-16
-15
OB 80- A8
80- A7
80- A6
34-A7 OPTXD
34-A8 S.GND
34-A9 OPRTS
OACB(1/3)
33 -14 80- A5 34-A10 OPRXD
LCDB LCD
36 80- A2 34-A13 DF_INT
-10
I 37 -9 80- A1 34-A14 APS_INT
I
or 38 -8
for DCPS
PC-402
42
LU-201 43
-2
-1
80-B10
80- B9
80- B8
80- B7
34-B5 S.GND
34-B6 LCDENB
34-B7 RST
34-B8 S.GND
Battery
J Backlight
80- B6
80- B5
34-B9 OPINT
34-B10 /FAX_RING CN52
J
2-2 INV ON
2-3 S.GND
80- B4 34-B11 5V
80- B3 34-B12 5V
2-1 5V
80- B2 34-B13 /SYS_STOP
(CN2)
58-1 F8.DRV
58-2 F8.LCK
80- B1 34-B14 /UTY
58-3 GND
for ENGINE 9-1 FL HOT
300:B11- B11
21 FS_TXD -4 FL GND
300:B10- B10 47-1 MONIT
22 S.GND (CN8)
300:B9 - B9
K 300:B8 - B8
300:B7 - B7
23
24
NC
FS_RTS
OB INVB 8- 3
-2
47-2 S.GND
K
FS-510 300:B6 - B6
300:B5 - B5
300:B4 - B4
25
26
27
28
S.GND
FS_RXD
NC
S.GND
-1
300:B3 - B3
or 300:B2 - B2
300:B1 - B1
29
30
31
FS_CTS
S.GND
S.GND
514: 1 - 2
SP FM10
L 300:A10- A10
for DCPS
24V2
PSWB SW2 514: 2 - 1
L
FS-511
11
300:A9 - A9
300:A8 - A8
300:A7 - A7
300:A6 - A6
12
13
14
15
24V2
24V2
P.GND
P.GND
OPERATION UNIT Speaker
+RU-502 300:A5 - A5
300:A4 - A4
300:A3 - A3
300:A2 - A2
16
19
20
P.GND
5V2
5V2
17 S.GND
300:A1 - A1
18 S.GND
M 300:A11- A11
M
1 2 3 4 5 6 7 8 9 10 11 12 13
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
L
F
K
E
B
A
H
D
C
14
14
17.2 Main body 2/4
Field Service Ver.2.0 Jan. 2007
15
15
CN500
IC-204
HD-505
16
16
J50: A1 - A12
50-A12 432-A1 /ENB1
J50: A2 - A11
-A11 -A2 /ALM1
J50: A3 - A10
-A10 -A3 /BIAS1
J50: A4 - A9
- A9 -A4 /S/H1
J50: A5 - A8
- A8 -A5 S.GND
J50: A6 - A7
- A7 -A6 LD+5V
J50: A7 - A6 46- 1 60- 1 S.GND
- A6 -A7 LD+5V
J50: A8 - A5 46- 2 - 2 TG
- A5 -A8 +5VRN
J50: A9 - A4 46- 3 - 3 CLAMP
- A4 -A9 S.GND
J50:A10 - A3 46- 4 - 4 ACLAMP
- A3 -A10 -VIDEO2
J50:A11 - A2 46- 5 - 5 PRD_KEEP
- A2 -A11 +VIDEO2
J50:A12 - A1 46- 6 - 6 GND
- A1 -A12 S.GND
17
17
46- 7 - 7 GMD
J50: B1 - B12 46- 8 - 8 +TCK
50-B12 432-B1 LOAD
J50: B2 - B11 46- 9 - 9 -TCK
-B11 -B2 DACLK
J50: B3 - B10 46-10 -10 S.GND
-B10 -B3 DI
J50: B4 - B9
LDB
- B9 -B4 S.GND 46-11 -11 S.GND
J50: B5 - B8 46-12 -12 +RCK
- B8 -B5 /ALM2
J50: B6 - B7 46-13
- B7 -B6 /BIAS2
J50: B7 - B6 46-14 -14 GND
- B6 -B7 /S/H2
J50: B8 - B5 46-15 -15 GND
- B5 -B8 /ALMRST
J50: B9 - B4 46-16 -16 +IN_CLK
- B4 -B9 S.GND
J50:B10 - B3 46-17
- B3 -B10 -VIDEO1
J50:B11 - B2 46-18 -18 GND
- B2 -B11 +VIDEO1
J50:B12 - B1 46-19 -19 GND
- B1 -B12 S.GND
46-20 -20 SCLK
18
18
19
19
INDEXB
- 2 DATA0 46-37 -37 S.GND
- 3 DATA1
- 4 DATA2 46-38 -38 ADRST
- 5 DATA3
- 6 DATA4 46-39 -39 APR
- 7 DATA5 46-40 -40 S.GND
- 8 DATA6
- 9 DATA7 46-41 -41 +5V
-10 ACK
-11 BUSY 46-42 -42 +5V
-12 PERROR 46-43 -43 +5V
-13 SLCT
-14 AUTOFD 46-44 -44 +5V
-15 N.C.
-16 GND 46-45 -45 S.GND
-17 GND 46-46 -46 +12V
-18 PERIHERAL
-19 GND 46-47 -47 +12V
-20 GND
-19 GND 46-48 -48 +12V
-22 GND 46-49 -49 +12V
-23 GND
20
20
45-4
45-3
45-2
45-1
- 9 RI
NRB
- 8 CTS
- 7 RTS
- 3 TXD
- 4 DTR
- 6 DSR
- 2 RXD
- 5 GND
21
21
57- 1 DCD
VDD
GND
-Data
+Data
22
22
-B50 LINESEL
-B49 CLKEN
-B48 3.3V
-B47 +12V
-B46 RST#
-B45 3.3V
-B44 CNT#
-B43 GND
-B42 PME#
-B41 GND
-B40 AD30
-B39 3.3V
-B38 AD28
-B37 AD26
-B36 AD24
-B35 IDSEL
-B34 GND
-B33 AD22
-B32 AD20
-B31 PAR
-B30 AD18
-B29 AD16
-B28 GND
-B27 FRAME#
-B26 TRDY#
-B25 STOP#
-B24 3.3V
-B23 DEVSEL#
-B22 GND
-B21 AD15
-B20 AD13
-B19 AD11
-B18 GND
-B17 AD9
-B16 C/BE#0
-B15 +5V(stby)
-B14 AD6
-B13 AD4
-B12 AD2
-B11 AD0
-B10 +5V(stby)
-B 9 +5V(main)
-B 8 SBDP1
-B 7 SBDM1
-B 6 GND
-B 5 SBDP2
-B 4 SBDM2
-B 3 +5V(main)
-B 2 IORST1
55-B 1 +5V(main)
-A50 INTA#
-A49 MONITOR
-A48 GND
-A47 GND
-A46 CLK
-A45 GND
-A44 REQ#
-A43 3.3V
-A42 AD31
-A41 AD29
-A40 GND
-A39 AD27
-A38 AD25
-A37 GND
-A36 C/BE#3
-A35 AD23
-A34 GND
-A33 AD21
-A32 AD19
-A31 GND
-A30 AD17
-A29 C/BE#2
-A28 IRDY#
-A27 GND
-A26 GND
-A25 SERR#
-A24 GND
-A23 PERR#
-A22 C/BE#1
-A21 AD14
-A20 GND
-A19 AD12
-A18 AD10
-A17 GND
-A16 AD8
-A15 AD7
-A14 +5V(STBY)
-A13 AD5
-A12 GND
-A11 AD3
-A10 +5V(STBY)
-A 9 AD1
-A 8 GND
-A 7 GND
-A 6 WAKEUP
-A 5 GND
-A 4 GND
-A 3 +5V(main)
-A 2 GND
55-A 1 +12V
(CN55:FX2)
Crimp
Symbol
Connector
24
24
Relay connector
Faston
25
25
MK-708+FK-502
26
26
L
F
K
E
B
A
H
D
C
M
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Y
X
V
S
P
U
R
N
Q
O
W
24V2 20- 1
5 6
24V2 20- 2 RL24V
5V-1 27-A11 5V P.GND 20- 3 7-6 P.GND
S.G-2
1
1
M1
H/L-7 27-A5 DRM_GAIN 5V 21- 10 3-1 5V2
17.3 Main body 3/4
2
2
M11
27-B7 FIXM_GAIN
P.G-8 27-B8 P.GND
P.G-9 27-B9 P.GND
DCPS(2/2)
FT35
24V1 16- 1 70- 6
P.GND 16- 2 70- 5
(DO/L)/BIAS1 16- 3 70- 4 Grid biass
(AO/2-8V)B_SIG 16- 4 70- 3
5V-1 32-A14 5V
FT40
S.G-2 32-A13 S.GND
P.GND 16- 5 70- 2
To developing bias
3
3
M3
H/L-7 32-A8 DEVM_GAIN
72- 1 J16-11
P.G-8 32-A7 P.GND
P.G-9 32-A6 P.GND (DI/L)/S_FB 15-1 71-11 FT30
24V-10 32-A5 24V2 (AO/4-10V) SDC_SIG 15-2 71-10
24V-11
HV
26-A4 24V2 (AO/4-10V) SAC_SIG 15-3 71- 9
To guide plate bias
FM1
32-A1 F1.DRV
(AO/4-10V) GRID_SIG 15-9 71- 3
4
4
917: 3 - 2
32-B14 GND
917: 2 - 3
Developing cooling fan 32-B13 /F7.LCK(DI/H)
917: 1 - 4
FM7
32-B12 F7.DRV
914: 3 - 1
Transfer
/F4.DRV 15-12
914: 2 - 2
(DI/H) /F4.LCK 15-13 Drum cooling fan
914: 1 - 3
FM4
5
5
CW/CCW-5 916: 3 - 1
/F6.DRV 15-15
Feed motor LD-6 32-B6 N.C. 916: 2 - 2
(DI/H) /F6.LCK 15-16 Developing suction fan
M9
H/L-7 32-B5 FEED_GAIN 916: 1 - 3
FM6
P.GND 15-17
P.G-8 32-B4 P.GND
P.G-9 32-B3 P.GND
24V-10 32-B2 24V2
24V-11 32-B1 24V2
J12: 7 - 1 J13:A4 - A1 980:1 - 1
(AI/0-5V) TH1.S 34-A1 Thermistor /1
J12: 6 - 2 J13:A3 - A2 980:2 - 2
S.GND 34-A2
TH1
/BP4 J15: 3 - 11
B
972-1
PS22
31-A3 MULTI_SIZE4(MULTI)
6
6
Ǿ3
RT3
931: 1 - 2 J15: 4 - 10 J12: 3 - 5 J13:B4 - B1 J18: 3 - 1 -3
Pick-up solenoid 31-A4 24V2 5V_R 34-A5
931: 2 - 1 J15: 5 - 9 J12: 2 - 6 J13:B3 - B2 J18: 2 - 2 -2 Fusing exit sensor
S.GND 34-A6
SD1
/BP 31-A5 MULTI_PICKUP_SD_DRV(MULTI)
J12: 1 - 7 J13:B2 - B3 J18: 1 - 3 953-1
PS3
VR1
Ǿ3
31-A8 5V
RT3
J05:1 - 3 987-1
PZS
TLEV_5V 34-A10
-3 J15: 9 - 5
31-A9 5V_R 903:6 - 1
-2 J15:10 - 4 TNR_A 34-A11
Lift sensor 31-A10 S.GND 903:5 - 2
973-1 J15:11 - 3 TNR_AB 34-A12
PS23
31-A11 MULTI_POSITION_PS 903:4 - 3
J15:12 - 2 TNR_B 34-A13
31-A12 MULTI_SET 903:3 - 4 Toner supply motor
J15:13 - 1 TNR_BB 34-A14
M4
7
7
24V2 34-A15
903:1 - 6
(J35:CT 2PIN)
24V2 34-A16
923: 1 - 2 J35: 1 - 4
31-A14 24V2 905:6 - 1
Vertical conveyance clutch 923: 2 - 1 J35: 2 - 3 BTLM_A 34-B1
CL3
31-A15 V_FEED_CL_DRV 905:5 - 2
BTLM_AB 34-B2
905:4 - 3
925: 1 - 2 J35: 3 - 2 BTLM_B 34-B3
31-A16 24V2 905:3 - 4 Toner bottle motor
Feed clutch /2 925: 2 - 1 J35: 4 - 1 BTLM_AB 34-B4
M10
905:2 - 5
CL5
31-A17 TRAY2_FEED_CL_DRV(LOWER)
24V2 34-B5
905:1 - 6
24V2 34-B6
PS24
974-1 J03: 3 -12
31-B3 DUP_PS1
935:2 - 1
8
8
B
SD5
Ǿ3
PS25
RT3
975-1 J03: 6 - 9
31-B6 DUP_PS2
J28: 6 - 1
-3 J03: 7 - 8 /F2.DRV 34-B11
31-A7 5V_R J28: 5 - 2 911: 2 - 2
ADU open -2 J03: 8 - 7 /F2.LCK(DI/H) 34-B12 Fusing cooling fan/Fr
31-A8 S.GND J28: 4 - 3 911: 1 - 3
FM2
976-1 J03: 9 - 6
31-B9 DUP_COVER
927: 1 - 2 J03:10 - 5
Ǿ3
RT3
ADU conveyance 31-B10 24V2
927: 2 - 1 J03:11 - 4
CL7
31-B13 DUP_CL2_DRV
9
9
J03:14 - 1
31-B14 N.C.
915: 1 - 3 J33: 1 - 3
31-B15 F5.DRV
915: 2 - 2 J33: 2 - 2
Coveyance suction fan 31-B16 P.GND
915: 3 - 1 J33: 3 - 1 J16-2 J11: 7 - 1
FM5
J16-7 J11: 2 - 6
IDC sensor
30-A2 TC_DRV
J16-15 932:2 - 1
-3 J04: 1 - 6 J07: 3 - 6 CLAW_SD_DRV 33-8
30-A3 5V_R J16-16 932:1 - 2 Drum claw solenoid
SD2
30-A5 TRAY1_EMPTY_PS(UPPER)
J16-12 937:2 - 1
24V2 33-10
J16-18 937:1 - 2 Erase lamp
EL
30-A8 TRAY1_FULL_PS(UPPER)
24V2 35-1
35-2
-3 J08: 1 - 12 /KEY.SIG 35-2
30-A9 5V_R 35-3
Paper empty sensor /2 -2 J08: 2 - 11 S.GND 35-3
30-A10 S.GND
962-1 J08: 3 - 10 KC.DRV 35-4
PS12
30-A11 TRAY2_EMPTY_PS(LOWER)
P.GND 35-5
-3 J08: 4 - 9
11
11
30-A12 5V_R
Upper limit sensor /2 -2 J08: 5 - 8
30-A13 S.GND
963-1 J08: 6 - 7 /M1 36-1
PS13
30-A14 TRAY2_FULL_PS(LOWER)
/PF 36-2
/PS0 36-3
-3 J08: 7 - 6 /PS1 36-4
30-A15 5V_R
-2 J08: 8 - 5 /PS2 36-5
Vertical conveyance sensor 30-A16 S.GND
952-1 J08: 9 - 4
PS2
30-A18 5V_R
Feed door -2 J08:11 - 2 /CPF1 36-9
30-A19 S.GND
open/close sensor 957-1 J08:12 - 1 P.GND 36-10
PS7
TXD 37-1
989-1 J17-2 J14: 1 - 4
30-B1 TDS_CONT S.GND 37-2
-2 J17-3 J14: 2 - 3
12
12
-5
RTS 37-6
S.GND 37-7
5V 37-8
924: 1 - 2
30-B5 24V2
Feed clutch /1 924: 2 - 1
CL4
30-B6 TRAY1_FEED_CL_DRV(UPPER)
-3 J27: 1 - 3
30-B7 5V_R
Paper empty sensor /BP -2 J27: 2 - 2
30-B8 S.GND
968-1 J27: 3 - 1
PS18
30-B9 MULTI_EMPTY_PS
13
13
-3 J10: 1 - 11
30-B10 5V_R
paper size sensor /BP1 -2 J10: 2 - 10
30-B11 S.GND
969-1 J10: 3 - 9
PS19
30-B12 MULTI_SIZE1
Z
T
Y
X
V
S
P
U
R
N
Q
O
W
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
Y
X
V
S
P
U
R
N
Q
O
W
-3 J10: 4 - 8
30-B13 5V_R
-2 J10: 5 - 7
Paper size sensor /BP2 30-B14 S.GND
970-1 J10: 6 - 6
PS20
30-B15 MULTI_SIZE2
201A: 1- 10
N.C. 17-10
14
14
201A: 2- 9
-3 J10: 7 - 5
ADF_RXD 17-9
30-B16 5V_R 201A: 3- 8
-2 J10: 8 - 4
N.C. 17-8
Paper size sensor /BP3 30-B17 S.GND 201A: 4- 7
971-1 J10: 9 - 3
ADF_TXD 17-7
201A: 5- 6
PS21
30-B18 MULTI_SIZE3 N.C. 17-6
201A: 6- 5
N.C. 17-5
17.4 Main body 4/4
201A: 7- 4
926: 1 - 2 J10:10 - 2 ADFOPEN 17-4
30-B19 24V2 201A: 8- 3
Feed clutch /BP 926: 2 - 1 J10:11 - 1 N.C. 17-3
CL6
30-B20 MULTI_FEED_CL_DRV(MULTI) 201A: 9- 2
N.C. 17-2
201A:10- 1
N.C. 17-1
Field Service Ver.2.0 Jan. 2007
201B: 1- 12
-3
ADS_BUSY 18-12
23-A1 5V_R 201B: 2- 11
-2
ADF_VV 18-11
Near-emptysensor/1 23-A2 S.GND 201B: 3- 10
959-1
ADF_DSET 18-10
PS9
23-A3 NEAR_EMPTY_PS(UPPER) 201B: 4- 9
ADF_SIZE1 18-9
201B: 5- 8
15
15
ADF_SIZE2 18-8
201B: 6- 7
-3
ADF_SIZE3 18-7
23-A4 5V_R 201B: 7- 6
ADF_NEXTPAGE 18-6
DF-607
Tray set sensor /1 -2 201B: 8- 5
23-A5 S.GND N.C. 18-5
958-1
PS8
23-A6 CASETTE_SET(UPPER) 201B: 9- 4
ADF_EMPTY_PS 18-4
201B:10- 3
5V1 18-3
201B:11- 2 200: 1 - 1 20: 1 - 1
-3
ADF_READY 18-2 24V 3
23-A7 5V_R 201B:12- 1 200: 4 - 4 20: 2 - 2
-2
SGND 18-1 P.GND 4
for DCPS
PS10
23-A9 WIDTH_PS1(UPPER)
-3
23-A10 5V_R
-2 62-1 U
Paper size sensor /Fr1 23-A11 S.GND
961-1 Scanner motor -2 V
M2
PS11
23-A12 WIDTH_PS2(UPPER)
16
16
-3 W
PSB/1
APS timing sensor -2 63-5 S.GND
PS31
-1 63-6 TIMING1
907- 2
24-A6 24V2 97-3 96-1 930-1 L.V. 931-4 63-7 24V
Paper lift motor /1 907- 1
M7
24-A7 LIFT_UP_M_DRV(UPPER) 97-1 96-3 -3 H.V. -3 63-8 LAMP_ON/OFF
L1 RLB -2 63-9 LAMP_EM
17
17
L1
-1 63-10 P.GND
L1 relay board L1 inverter
L1 INVB
-3
25-A1 5V_R
-2
Near-emptysensor/2 25-A2 S.GND Exposure lamp
965-1 (J22:CT)
PS15
25-A3 NEAR_EMPTY_PS(LOWER)
J22: 1 - 2
930-2 64-1 ADF_CLOSE_SIG
DF open/close switch J22: 2 - 1
-1
SW3
-3
64-2 S.GND
25-A4 5V_R
-2
Tray set sensor /2 25-A5 S.GND
964-1 -4
PS14
25-A6 CASETTE_SET(LOWER) 64-3 KC_24V
936B-1 -3
64-4 KC.DRV
936B-2 -2
-3 64-5 /KEY.SIG
26-A1 5V_R 985A-1
-2 64-6 S.GND
26-A2 S.GND
Key counter
PS16
26-A3 WIDTH_PS1(LOWER)
18
18
-1 64-9 S.GND
-3
26-A4 5V_R
-2
Paper size sensor /Fr2 26-A5 S.GND KC_24V 28-A1 61- A12
967-1
PS17
26-A6 WIDTH_PS2(LOWER) APS_SIG_IN 28-A2 61- A11
APS_5V 28-A3 61- A10
S_DA_DATA 28-A4 61- A9
OPM_EN 28-A5 61- A8
-5 26-A7 FD_SIZE1(LOWER) S.GND 28-A6 61- A7
-4 26-A8 FD_SIZE2(LOWER) OPM_CLK 28-A7 61- A6
Paper size board /2 -3 26-A9 FD_SIZE3(LOWER) OPM_MODE_C 28-A8 61- A5
-2 26-A10 FD_SIZE4(LOWER) DF_CLOSE_SIG 28-A9 61- A4
98-1 26-A11 S.GND XENON_EM 28-A10 61- A3
PSB/2
S.GND 28-A11 61- A2
19
19
M8
26-A13 LIFT_UP_M_DRV(LOWER) XENON_ON 28-B3 61- B10
5V2 28-B4 61- B9
5V2 28-B5 61- B8
OPM_DIR 28-B6 61- B7
OPM_MODE_B 28-B7 61- B6
986-4 J09 1 - 4 OPM_MODE_A 28-B8
22-B1 N.C. 61- B5
-3 J09 2 - 3 S_DA_LATCH 28-B9
22-B2 S.GND 61- B4
Humidity sensor -2 J09 3 - 2 S_DA_CLK 28-B10
22-B3 HUMS_SIG 61- B3
-1 J09 4 - 1 65- 2 P.GND 2
HUMS
22-B4 5V /KC_DRV 28-B11 61- B2
KCSIG_IN 28-B12 65- 1 24V2 1
61- B1
for DCPS
921: 1 - 2 J39: 1 - 7
22-B5 24V2
20
20
CL1
22-B8 RESIST_CL_DRV
922: 1 - 2 J01: 1 - 5
22-B7 24V2
Loop clutch 922: 2 - 1 J01: 2 - 4 B_VV 38-1 43-20
CL2
48-5 CT
22-B6 LOOP_CL_DRV
48-8 FG
48-7 NC
48-2 TX-
48-6 RX-
48-1 TX+
48-4 RX+
48-3 RX+
48-11 LED2
48-10 LED1
48-12 VDD2
PS1
22-B11 5V
/EG_RTS 38-7 43-14
EG_TXD 38-8 43-13
BK
J54: - 6 /EG_CTS 38-9 43-12
22-B12 5V_R
Ǿ3
RT3
J54: - 5
22-B13 S.GND EG_RXD 38-10 43-11
21
21
J54: - 4
S.GND 38-11 43-10
S.GND 38-12 43- 9
J54: - 3 5V1 38-13 43- 8
22-B15 5V_R
J54: - 2 S.GND 38-14 43- 7
22-B16 S.GND
J54: - 1 /EG_RST 38-15 43- 6
Ǿ3
RT3
BK
APS_TIM_IN 38-16 43- 5
938:2 - 1 J02: 1 - 2
NMI_SIG 38-17 43- 4
22-B18 TSL_DRV FIX_OK_IN 38-18 43- 3
Transfer exposure lamp 1-2 J02: 2 - 1
TSL
OACB(3/3)
BK
Ǿ3
RT3
J63: 1 - 19
22-A1 S.GND
J63: 2 - 18
22-A2 LT_TRAY_UP_M_ON
22
22
J63: 3 - 17
22-A3 LU_CLOSE_IN
J63: 4 - 16
22-A4 LU_FEED_M_H/L
J63: 5 - 15
22-A5 LU_FEED__M_CLK
J63: 6 - 14
22-A6 LU_FEED_M_ON
J63: 7 - 13
Ǿ3
22-A7 LU_SD_DRIVE
RT3
BK
J63: 8 - 12
22-A8 LU_CL_DRIVE J31: 8 - 1
J63: 9 - 11 JOB_TRAY_SET 29-A1
22-A9 LU_JAM_IN J31: 7 - 2
J63:10 - 10 S.GND 29-A2
22-A10 LU_FULL_PS_IN
J63:11 - 9
22-A11 LU_EMPTY_PS_IN J31: 6 - 3
J63:12 - 8 5V_R 29-A3
22-A12 LU_SET1_IN J31: 5 - 4
J63:13 - 7 S.GND 29-A4
22-A13 LU_SET2_IN J31: 4 - 5
J63:14 - 6 JOB_TRAY_EMPTY_PS 29-A5
22-A14 LU_SET_IN
J63:15 - 5
22-A15 LU_TYPE_IN J31: 3 - 6
J63:16 - 4
JS-502
5V_R 29-A6
22-A16 5V J31: 2 - 7
J63:17 - 3 S.GND 29-A7
EMPTY PS FULL PS
23
23
22-A17 5V J31: 1 - 8
JOB TRAY JOB TRAY
22-A19 S.GND
J30: 6 - 1 913: 3 - 1
/F3.DRV 29-A9
(J51:CT) J30: 5 - 2 913: 2 - 2
P.GND 29-A10 Exhaust fan /Fr
J51:5 - 1 J30: 4 - 3 913: 1 - 3
FM3
J30: 1 - 6
/F9.LCK(DI/H) 29-A14
J61 : 1 - 12
19-A1 LCC_FLM
J61 : 2 - 11 J32:11 - 1 906-4
24
19-A2 S.GND
24
REVERSE_M_XB 29-B1
J61 : 3 - 10 J32:10 - 2 -3
19-A3 S.GND REVERSE_M_B 29-B2 Reverse motor
J61 : 4 - 9 J32: 9 - 3 -2
19-A4 5V2 REVERSE_M_XA 29-B3
M6
J61 : 5 - 8 J32: 8 - 4 -1
19-A5 5V2 REVERSE_M_A 29-B4
J61 : 6 - 7
19-A6 LCC_RTS
J61 : 7 - 6
19-A7 LCC_RXD 24V2 29-B5 J32: 7 - 5 933:2 - 1
J61 : 8 - 5
19-A8 LCC_TXD REVERSE_SD 29-B6 J32: 6 - 6 933:1 - 2 Reverse solenoid
SD3
J61 : 9 - 4
for DB/LCC UNIT
19-A9 LCC_CLK
J61 :10 - 3
19-A10 N.C.
J61 :11 - 2 J32: 5 - 7 -3
19-A11 P.GND 5V_R 29-B7
REVERSE UNIT
REVERSE_PS 29-B9
J32: 2 - 10
19-B1 FS_TXD REVERSE_UNIT_SET 29-B10
J32: 1 - 11
19-B2 S.GND S.GND 29-B11
25
25
19-B3 N.C
19-B4 FS_RTS
J06:3 - 1 -3
19-B5 S.GND 5V_R 29-B12
J06:2 - 2 -2
19-B6 FS_RXD S.GND 29-B13 Toner bottle sensor
J06:1 - 3 954-1
PS4
19-B8 S.GND
19-B9 FS_CTS
19-B10 S.GND
J48:3 - 1 -3
21 22 23 24 25 26 27 28 29 30 31
TNRB.PS(DI/H) 69-3
J64-2
26
26
11-1 DH_REM
J64-1
11-3 24V
for DH
11-2 NC
Z
T
Y
X
V
S
P
U
R
N
Q
O
W
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
PS9
CN15
PS8
PS9 ON
PS10
PS10 ON
CN16
Cover open/close sensor PS7 ON
PS7 CN14
MOSDB
SD2
SD2
PS2 ON
DFCB
LB
PS6 ON
solenoid
PS6
PS1
sensor/1
Original size
PS3
sensor/3
Original conveyance motor
M2
PS1 ON
Original size
PS3 ON PS1 ON PS1 ON
PS4
PS4 ON PS4 ON
PS4 ON PS2 ON PS2 ON
CN17
Original size
TB
PS2 ON VR ON VR ON
PS2
VR ON
Original size VR
CN19
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
H
D
C
G
17.6.1
17.6 PC
PC-202
1
1
Field Service Ver.2.0 Jan. 2007
2
2
3
3
M125
Paper feed sensor /3
PS116
Near-emptysensor/4
PS122
Vertical conveyance sensor /3
PS117
PSDB4
4
4
PSDB4
Paper size detect board /4 Right door open/close sensor
PS111
PS121
Vertical conveyance motor /3
M120
5
5
PCCB
6
6
PSDB3
Paper size detect board /3
7
7
8
8
Crimp
Symbol
Connector
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
H
D
C
G
17.6.2
PC-402
1
1
Field Service Ver.2.0 Jan. 2007
2
2
RLB
SW1
3
3
PS13
Shift home sensor
PS12
Shift position sensor
PS11
MEB
MEB
4
4
RLB
Paper lift motor encoder sensor
PS10
5
5
Shift motor
M4
PCCB
6
6
7
7
8
8
Crimp
Symbol
Connector
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
17.7 LU
bizhub 500/420/360
1 2 3 4 5 6 7 8 9
A A
Dehumidifier heater
OPTIONAL
HTR101
114-3 24V
J121-1 J121-2
114-2 P_GND
B NC (2pin) B
MS
151
FT102 (4pin)
114-4 24V Upper door interlock switch
FT101 (1pin)
114-1 T5M_24V
121- 1
112-1 T5M_24V
112-2 T5M_ON
121- 2 M151 Paper lift motor
J62- 1 24V 111- 1 24V 112-3 P_GND
C J62- 2 PGND
J62- 3 24V
111- 2 PGND
C
J62- 4 RL_POWER 112-4 24V 120-11
112-5 24V -10
112-6 P_GND -9
112-7 P_GND -8
112-8 LUM_HL -7
(LD)
112-9 LUM_FR
-6
-5
M150 Feed motor
112-10 LUM_CLK -4
D J63-19 SGND 110- 1 SGND
112-11 LUM_ON
112-12 SGND
-3
-2
D
J63-18 SGND 110- 2 SGND
112-13 5V -1
J63-17 5V2 110- 3 5V2
J63-16 5V2 110- 4 5V2
J63-15 LU_TYPE 110- 5 LU_TYPE
J63-14 T5_SET_PS 110- 6 T5_SET_PS
J63-13 T5_SET2 110- 7 T5_SET2
J82: 5- 1 J84: 2 - 1
J63-12 T5_SET1 110- 8 T5_SET1 113- A1 24V
J82: 4- 2 J84: 1 - 2 SD151 Pick-up solenoid
J63-11 T5_ZERO_PS 110- 9 T5_ZERO_PS 113- A2 T5SD_DRV
E J63-10 T5_FULL_PS
J63- 9 LU_JAM_PS
110-10 T5_FULL_PS
110-11 LU_JAM_PS J82: 3- 3 127- 3
E
110-12 LU_CL_ON 113- A3 S_GND
J63- 8 LU_CL_ON J82: 2- 4 -2
113- A4 LCT_JAM PS155 LU exit sensor
J63- 7 T5_SD_ON 110-13 T5_SD_ON J82: 1- 5 -1
113- A5 5V
J63- 6 LUM_ON 110-14 LUM_ON
J63- 5 LUM_CLK 110-15 LUM_CLK
J83: 6- 1 125- 3
J63- 4 LUM_HL 110-16 LUM_HL 113- A6 S_GND
J83: 5- 2 -2 Upper limit sensor
J63- 3 T5_CLOSE 110-17 T5_CLOSE 113- A7 T5_FULL PS152
J83: 4- 3 -1
J63- 2 T5_UPM_ON 110-18 T5_UPM_ON 113- A8 5V
126- 3
113- B1 S_GND
-2
113- B2 T5_SET1 PS154 Remaining paper sensor/1
-1
113- B3 5V
G 113- B4 S_GND
122- 3
G
-2
113- B5 T5_SET2 PS151 Remaining paper sensor/2
-1
113- B6 5V
129- 3
113- B7 S_GND
-2
113- B8 LU_SET PS156 LU set sensor
-1
Main body 113- B9 5V
H J85: 2 - 1
H
Symbol
113-B10 LUCL_DRV
J85: 1 - 2 CL151 Feed clutch
113-B11 24V
LUDB
Connector Faston
I Crimp Relay connector I
1 2 3 4 5 6 7 8 9
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
17.8 FS
bizhub 500/420/360
17.8.1 FS-510/PU-501
1 2 3 4 5 6 7 8 9
SW4 Guide plate switch
SD-502/MT-501
A (Option) PS5
Conveyance sensor A
Exit roller home sensor
PS12
GND
GND
GND
Chopper Unit Setting Detection
GND
PJ8
M1 Exit motor
E PU-501(Option) E
M7 Stapler movement motor
PS14
Lower limit sensor
1 2 3 4 5 6 7 8 9
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
bizhub 500/420/360
1 2 3 4 5 6 7 8 9
SW4 Hole punch position switch
W W
Intermediate conveyance W W
M12 Stapler moving motor M6 Hole punch Only for inch
roller release motor B
B M14 destination
A selector motor
A
CL1 Punch clutch
Paper exit motor M3
Conveyance motor/Lw M2
M9 Paddle motor/Lw
Conveyance motor/Up M4
Punch encoder sensor
PS15
PS1
Door sensor (RU-502)
Sift motor M8
M13 Paper exit roller release motor
SW3
Main tray lower limit switch
SW1
Interlock switch PWB-E_GL
LED19 Main tray upper limit LED
F CN200C
PS18 Upper door sensor
F
RU-502 Front door sensor
PS17
CN201B
PWD-F_GL
PWD-F
Bypass route conveyance sensor
PS2
PWD-F
Alignment home sensor PS19 Main tray upper limit sensor
Faston
PS9
Connector
PWD-F_GL
1 2 3 4 5 6 7 8 9
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
H
D
C
G
17.9 SD
1
1
Field Service Ver.2.0 Jan. 2007
2
2
3
3
Exit sensor
PS20
4
4
SDCB
5
5
SD interlock switch
SW4
6
6
Conveyance motor
M8
FS-510
7
7
Folding motor
M10
8
8
Crimp
Symbol
Connector
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
H
D
C
G
17.10 MT
1
1
Field Service Ver.2.0 Jan. 2007
2
2
3
3
Gate solenoid /3
SD3
Conveyance motor
M1
4
4
SD2
5
5
MTCB
Gate solenoid /1
SD1
6
6
FS-510
7
7
8
8
Crimp
Symbol
Connector
9
9
Relay connector
Faston
I
F
E
B
A
H
D
C
G
17. OVERALL WIRING DIAGRAM
bizhub 500/420/360
17. OVERALL WIRING DIAGRAM Field Service Ver.2.0 Jan. 2007
bizhub 500/420/360
DF-607
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
DF-607
DF-607
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
MAINTENANCE
2. PERIODIC CHECK..................................................................................................5
2.1 Maintenance procedure ........................................................................................5
2.1.1 Replacing the Pick-up Roller and Feed Roller ..............................................5
2.1.2 Replacing the Separation Roller....................................................................6
2.1.3 Cleaning of the Pick-up Roller, Feed Roller and Separation Roller ..............7
2.1.4 Cleaning of Miscellaneous Rollers ................................................................8
2.1.5 Cleaning of the Scanning Guide..................................................................11
2.1.6 Cleaning of the Reflective Sensor Section ..................................................12
3. OTHER ..................................................................................................................13
3.1 Disassembly/Adjustment prohibited items ..........................................................13
3.2 Disassembling and assembling list .....................................................................14
3.3 Disassembling and assembling procedure .........................................................14
3.3.1 Cover /Fr, Cover /Rr and Original Feed Tray Cover /Lw .............................14
3.3.2 DF Control Board (DFCB) ...........................................................................15
3.3.3 Original Size VR (VR1)................................................................................15
3.3.4 Complete Stamp Unit 2 ...............................................................................17
3.3.5 Replacing the Replace Stamp 2..................................................................18
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT..............................................................................19
4.1 Leading Edge Skew Adjustment .........................................................................19
i
CONTENTS Field Service Ver.2.0 Jan. 2007
DF-607
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
DF-607
A. Type
B. Functions
C. Paper type
1-Sided Mode
Standard Mode 35 to 128 g/m2 (9.25 to 34 lbs)
Plain Paper 2-Sided Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Mixed Original Detection
1-Sided / 2-Sided Mode
Type of Document Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Plain Paper
1-Sided Mode
FAX Mode 35 to 128 g/m2 (9.25 to 34 lbs)
Plain Paper 2-Sided Mode
50 to 128 g/m2 (13.25 to 34 lbs)
Inch area
A3, A4S, A4, B4, B5S, B5
Detectable Document 11 x 17, 81/2 x 14, 81/2 x 11S, 81/2 x 11, 81/2 x 51/2S, 81/2 x 51/2
Size*1 Metric area
A3, A4S, A4, A5S, A5, B4, B5S, B5, B6S
11 x 17, 81/2 x 11S, 81/2 x 11
Capacity 80 sheets (80 g/m2) or load height of 11 mm or less.
*1: For the Combined Original Detection Mode, Refer to the Mixed Original Detection Enabled
Size Combination Table.
1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
2
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
DF-607
Reference original (original with a maximum width)
A3 A4 B4S B5 A4S A5 B5S A5
Other A3 U { — — — — — —
originals A4 { U — — — — — —
B4S ~ ~ U { — — — —
B5 ~ ~ { U — — — —
A4S ~ ~ ~ ~ U { — —
A5 ~ ~ ~ ~ { U — —
B5S X X ~ ~ ~ ~ U —
A5S X X X X X X X U
U: Same size {: Same group ~: Different group X: Mix prohibited —: No need to set
For Inch
G. Maintenance
H. Machine data
I. Operating environment
Temperature 10 to 30°C
Humidity 10 to 80% RH (with no condensation)
NOTE
• These specifications are subject to change without notice.
3
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
DF-607
Blank Page
4
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
MAINTENANCE
2. PERIODIC CHECK
DF-607
2.1 Maintenance procedure
NOTE
• The alcohol described in the cleaning procedure of Maintenance represents the iso-
propyl alcohol.
B. Procedure
1. Open the Open/Close Cover [1].
[1]
16eaf2c001na
[3]
[2]
16eaf2c002na
[4]
16eaf2c003na
5
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[7]
7. Remove the belt [9].
[13] [9] 8. Remove the Pick-up Roller Shaft [11]
from the Arm /Rr [10].
[12]
[11] 9. Remove the 2 Spacers [12] from the
Pick-up Roller Shaft.
[6]
10. Remove two Pick-up Rollers [13].
[7] NOTE
• Be sure to take note of the direction of
[8]
the pick-up roller when installing it.
[10]
16eaf2c004na
[18] 16eaf2c005na
B. Procedure
1. Open the Open/Close Cover [1].
[1]
16eaf2c006na
[3]
[2] 16eaf2c007na
6
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
DF-607
bottom side of the Separation Roller
Assy.
16eaf2c008na
[5] [6]
16eaf2c009na
16eaf2c010na
2.1.3 Cleaning of the Pick-up Roller, Feed Roller and Separation Roller
A. Periodic cleaning parts/cycle
• Pick-up Roller: Every 250,000 prints (Actual replacement cycle: Every 50,000 faces)
• Feed Roller: Every 250,000 prints (Actual replacement cycle: Every 50,000 faces)
• Separation Roller: Every 250,000 prints (Actual replacement cycle: Every 50,000 faces)
B. Procedure
1. Open the Open/Close Cover [1].
[1]
16eaf2c011na
7
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[3]
[4]
[2] 16eaf2c012na
B. Procedure
1. Open the Open/Close Cover [1].
[2] 2. Using a soft cloth dampened with alco-
hol, wipe the roller [2].
16eaf2c013na
[2]
[1]
16eaf2c017na
[4]
16eaf2c014na
8 1
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
[4] [3]
DF-607
16eaf2c018na
16eaf2c015na
[6]
[6]
16eaf2c016na
[5]
[5] 16eaf2c019na
1 9
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[6]
16eaf2c020na
[7]
16eaf2c021na
10
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
DF-607
[9]
16eaf2c022na
[10]
[10]
16eaf2c023na
B. Procedure
1. Open the DF.
2. Using a soft cloth dampened with alco-
[1] hol, wipe the Scanning Guide [1].
16eaf2c024na
11
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
B. Procedure
1. Clean the Original Size Sensor /2 (PS2)
[1] [1] using a brush or other similar tools.
16eaf2c025na
12
Field Service Ver.2.0 Jan. 2007 3. OTHER
3. OTHER
3.1 Disassembly/Adjustment prohibited items
DF-607
A. Screws to which blue paint or green paint is applied
• Blue paint or green paint is applied to some screws to prevent them from coming
loose.
• As a general rule, screws to which blue paint or green paint is applied should not be
removed or loosened.
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
Caution
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
13
3. OTHER Field Service Ver.2.0 Jan. 2007
[3]
[9]
[4]
[5] [7]
[2]
[6]
[8]
[1]
16eaf2c026na
1. Remove two screws [1], and remove the Cover /Fr [2].
2. Remove the 2 Screws [3] and raise the Original Feed Tray. Open DF to release the Lock
Claws (at 2 places) and then remove the Cover /Rr [4].
3. Remove the screw [5] and the washer [6], and remove the stopper [7].
4. Lift up the Original Feed Tray.
5. Remove four screws [8], and remove the Original Feed Tray Cover /Lw [9].
14
Field Service Ver.2.0 Jan. 2007 3. OTHER
[1]
1. Turn OFF the Main Power Switch
DF-607
(SW1).
2. Remove the Cover /Rr.
(See P.14)
[1] 3. Disconnect all the connectors on the DF
Control Board (DFCB).
4. Remove three screws [1], and then
[2] remove the DFCB [2].
16eaf2c027na
NOTE
• When DFCB is replaced, be sure to conduct the back-up data initialization, the origi-
nal width detection adjustment and the rewrite of the firmware.
A. Removal Procedure
[1] 1. Turn OFF the Main Power Switch
[2]
(SW1).
2. Remove the Original Feed Tray Cover
[3] /Lw.
[2]
(See P.14)
3. Disconnect the connector [1].
4. Remove two screws [2] and the mount-
16eaf2c028na ing plate [3].
16eaf2c029na
[7] 16eaf2c030na
15
3. OTHER Field Service Ver.2.0 Jan. 2007
B. Reinstallation Procedure
[1]
1. Close the Side Edge Stop [1] of the
Original Feed Tray.
DF-607
NOTE
• Be sure to perform document width
detection adjustment after replacing
the Original Size VR (VR1).
(See P.235 "10.8 ADF" in Field Service
16eaf2c031na bizhub 500/420/360 main body.)
[4]
16eaf2c032na
16eaf2c033na
16eaf2c034na
[9] 16eaf2c035na
7. Install the Original Feed Tray Cover /Lw and turn ON the Main Power Switch (SW1).
16
Field Service Ver.2.0 Jan. 2007 3. OTHER
NOTE
• When VR1 is replaced, be sure to conduct the back-up data initialization and the orig-
inal width detection adjustment.
DF-607
3.3.4 Complete Stamp Unit 2
1. Open the Open/Close Cover [1].
2. Open the Processing Guide [2].
[2]
[1]
16eaf2c036na
[4]
16eaf2c037na
[6]
[7]
16eaf2c038na
17
3. OTHER Field Service Ver.2.0 Jan. 2007
[1]
16eaf2c039na
16eaf2c040na
18
Field Service Ver.2.0 Jan. 2007 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT
DF-607
4.1 Leading Edge Skew Adjustment
1. Load the test chart [1] in the DF and
[1] make one 1-sided copy five consecutive
times.
16eaf3c001na
16eaf3c002na
[2] [3]
16eaf3c003na
16eaf3c004na
19
4. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
16eaf3c005na
16eaf3c006na
20 1
SERVICE MANUAL Field Service
PC-202
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
PC-202
PC-202
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
MAINTENANCE
2. PERIODIC CHECK..................................................................................................3
2.1 Maintenance procedure ........................................................................................3
2.1.1 Replacing the Separation Roller Assy...........................................................3
2.1.2 Replacing the Feed Roller.............................................................................4
2.1.3 Replacing the Pick-up Roller .........................................................................7
3. OTHER ....................................................................................................................9
3.1 Disassembly/Adjustment prohibited items ............................................................9
3.2 Disassembling, assembling and cleaning list......................................................10
3.2.1 Disassembling and assembling list .............................................................10
3.2.2 Cleaning list.................................................................................................10
3.3 Disassembling and assembling procedure .........................................................11
3.3.1 Right Door/Rear Right Cover/Lower Right Cover/Front Right Cover ..........11
3.3.2 Rear Cover ..................................................................................................11
3.4 Cleaning procedure.............................................................................................12
3.4.1 Separation Roller.........................................................................................12
3.4.2 Feed Roller..................................................................................................13
3.4.3 Pick-up Roller ..............................................................................................13
3.4.4 Vertical Conveyance Roller .........................................................................13
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT..............................................................................15
4.1 Mis-centering adjustment of the Trays 3 and 4...................................................15
i
CONTENTS Field Service Ver.2.0 Jan. 2007
PC-202
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
PC-202
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
PC-202
Blank Page
2
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
MAINTENANCE
2. PERIODIC CHECK
PC-202
2.1 Maintenance procedure
2.1.1 Replacing the Separation Roller Assy
A. Periodically replaced part/cycle
• Separation Roller Assy: Every 750,000 prints (Actual replacement cycle: Every 300,000
prints)
NOTE
• Replace the Separation Roller Assy, Feed Roller and Pick-up Roller at the same time.
B. Procedure
1. Remove the Right Door.
[2] (See P.11)
2. Remove two screws [1] and remove the
Jam Access Cover [2].
[1] 4061f2c001na
[3]
4061f2c002na
[5]
4061f2c003na
3
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[8]
4061f2c004na
NOTE
• When installing the Separation Roller
Mounting Plate Assy, be sure to fix the
holder with screws while holding it
down.
4061f2c005na
NOTE
• Replace the Separation Roller Assy, Feed Roller and Pick-up Roller at the same time.
B. Procedure
1. Remove the Rear Right Cover.
[2] [1] (Remove the Right Lower Cover for
Tray 4.)
(See P.11)
2. Remove the Tray.
3. Remove the Separation Roller Mounting
Plate Assy.
(See P.3)
4. Disconnect the connector [1] (Tray 3),
two connectors [2] (Tray 4) and remove
the harness from two wire saddles.
NOTE
4061f2c006na • Be careful not to confuse the connec-
tor of the Tray 3 with the connectors of
the Tray 4.
4
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
PC-202
[3]
[3] 4061f2c007na
[6]
4061f2c008na
[7]
4061f2c009na
4061f2c010na
5
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[13]
[12]
4061f2c011na
[15]
[14]
4061f2c012na
[18]
4061f2c013na
[21]
4061f2c014na
6
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
PC-202
NOTE
• Replace the Separation Roller Assy, Feed Roller and Pick-up Roller at the same time.
B. Procedure
1. Remove the Rear Right Cover.
[1] (Remove the Right Lower Cover for
Tray 4.)
(See P.11)
2. Remove the Tray.
3. Remove the Separation Roller Mounting
Plate Assy.
(See P.3)
4. Disconnect the connector [1] and
remove the harness from two wire sad-
dles.
4061f2c015na
[2]
[2] 4061f2c016na
[5]
4061f2c017na
7
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[6]
4061f2c018na
[9]
[9]
[10] 4061f2c019na
4061f2c020na
8
Field Service Ver.2.0 Jan. 2007 3. OTHER
3. OTHER
3.1 Disassembly/Adjustment prohibited items
PC-202
A. Screws to which blue paint or green paint is applied
• Blue paint or green paint is applied to some screws to prevent them from coming
loose.
• As a general rule, screws to which blue paint or green paint is applied should not be
removed or loosened.
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
CAUTION
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
9
3. OTHER Field Service Ver.2.0 Jan. 2007
10
Field Service Ver.2.0 Jan. 2007 3. OTHER
PC-202
[1] 1. Open the Right Door [1].
[3] 2. Remove the Right Door [1].
[2]
3. Remove two screws [2] and remove the
Rear Right Cover [3].
4. Remove two screws [4] and remove the
Lower Right Cover [5].
5. Remove two screws [6] and remove the
Front Right Cover [7].
[4]
[5]
[7] [6] 4061f2c021na
[2]
[1] 4061f2c022na
11
3. OTHER Field Service Ver.2.0 Jan. 2007
• The alcohol described in the cleaning procedure represents the isopropyl alcohol.
B. Procedure
1. Remove the Right Door.
[2] (See P.11)
2. Remove two screws [1] and remove the
Jam Access Cover [2].
[1] 4061f2c023na
[3]
4061f2c024na
4061f2c025na
12
Field Service Ver.2.0 Jan. 2007 3. OTHER
PC-202
B. Procedure
1. Remove the Tray 3.
[1] 2. Remove the Separation Roller Mounting
Plate Assy.
(See P.12)
3. Using a soft cloth dampened with alco-
hol, wipe the Feed Roller [1] clean of
dirt.
4. Repeat steps 1 to 3 similarly for the
Tray 4.
4061f2c026na
B. Procedure
1. Remove the Tray 3.
[1] 2. Remove the Separation Roller Mounting
Plate Assy.
(See P.12)
3. Using a soft cloth dampened with alco-
hol, wipe the Pick-up Roller [1].
4. Repeat steps 1 to 3 similarly for the
Tray 4.
4061f2c027na
B. Procedure
1. Open the Right Door.
2. Using a soft cloth dampened with alco-
hol, wipe the Vertical Conveyance
Roller [1].
[1]
4061f2c028na
13
3. OTHER Field Service Ver.2.0 Jan. 2007
PC-202
Blank Page
14
Field Service Ver.2.0 Jan. 2007 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT
PC-202
4.1 Mis-centering adjustment of the Trays 3 and 4
Conduct this adjustment when a mis-centering occurs that cannot be adjusted in the service
mode.
A. Procedure
1. Pull out the Tray [1].
2. If there remains any paper, remove it
thoroughly.
3. Loosen the 2 screws [2].
4. Move the Paper Guide [3] and adjust
the center position with the marking-off
[4] as a guide.
5. Tighten the 2 screws [2].
[1] 4061f3c001na
15
4. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
PC-202
Blank Page
16
SERVICE MANUAL Field Service
PC-402
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
PC-402
PC-402
OUTLINE
1. PRODUCT SPECIFICATION ..................................................................................1
MAINTENANCE
2. PERIODIC CHECK..................................................................................................3
2.1 Maintenance procedure ........................................................................................3
2.1.1 Replacing the Separation Roller Assy...........................................................3
2.1.2 Replacing the Feed Roller.............................................................................4
2.1.3 Replacing the Pick-up Roller .........................................................................7
3. OTHER ....................................................................................................................9
3.1 Disassembly/Adjustment prohibited items ............................................................9
3.2 Disassembling, assembling and cleaning list......................................................10
3.2.1 Disassembling and assembling list .............................................................10
3.2.2 Cleaning list.................................................................................................10
3.3 Disassembling and assembling procedure .........................................................11
3.3.1 Right Door/Rear Right Cover/Lower Right Cover/Front Right Cover ..........11
3.3.2 Rear Cover ..................................................................................................11
3.3.3 Tray .............................................................................................................12
3.3.4 Wire .............................................................................................................13
3.4 Cleaning procedure.............................................................................................16
3.4.1 Separation Roller.........................................................................................16
3.4.2 Feed Roller..................................................................................................16
3.4.3 Pick-up Roller ..............................................................................................17
3.4.4 Vertical Conveyance Roller .........................................................................17
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT..............................................................................19
4.1 Mis-centering adjustment....................................................................................19
4.2 Shifter Movement Timing Belt Adjustment..........................................................21
i
CONTENTS Field Service Ver.2.0 Jan. 2007
PC-402
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATION
OUTLINE
1. PRODUCT SPECIFICATION
PC-402
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATION Field Service Ver.2.0 Jan. 2007
PC-402
Blank Page
2
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
MAINTENANCE
2. PERIODIC CHECK
PC-402
2.1 Maintenance procedure
2.1.1 Replacing the Separation Roller Assy
A. Periodically replaced part/cycle
• Separation Roller Assy: Every 750,000 prints (Actual replacement cycle: Every 300,000
prints)
NOTE
• Replace the Separation Roller Assy, Feed Roller and Pick-up Roller at the same time.
B. Procedure
1. Remove the Right Door.
[2]
(See P.11)
2. Remove two screws [1] and remove the
Separation Roller Mounting Plate Assy
[2].
[1]
4061f2c201na
[3]
4061f2c202na
[6]
4061f2c203na
3
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
NOTE
• When installing the Separation Roller
Mounting Plate Assy, be sure to fix the
PC-402
4061f2c204na
B. Procedure
1. Remove the Rear Cover and the Rear
[1]
Right Cover.
(See P.11)
2. Remove the Tray.
3. Remove the Separation Roller Mounting
Plate Assy.
(See P.3)
4. Disconnect the connector [1] from the
PC Control Board (PCCB).
4061f2c205na
[2]
[2]
4061f2c206na
4
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
PC-402
[4]
[5]
4061f2c207na
[6]
4061f2c208na
[8]
[9]
4061f2c209na
5
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[12]
[11]
4061f2c210na
[14]
4061f2c211na
[17]
4061f2c212na
6
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
PC-402
NOTE
• Replace the Separation Roller Assy, Feed Roller and Pick-up Roller at the same time.
B. Procedure
1. Remove the Rear Cover and the Rear
[1]
Right Cover.
(See P.11)
2. Remove the Tray.
3. Remove the Separation Roller Mounting
Plate Assy.
(See P.3)
4. Disconnect the connector [1] from the
PC Control Board (PCCB).
4061f2c213na
[2]
[2]
4061f2c214na
[5]
4061f2c215na
7
2. PERIODIC CHECK Field Service Ver.2.0 Jan. 2007
[7]
[6]
4061f2c216na
[9]
[9]
[10]
4061f2c217na
[12]
4061f2c218na
8
Field Service Ver.2.0 Jan. 2007 3. OTHER
3. OTHER
3.1 Disassembly/Adjustment prohibited items
PC-402
A. Screws to which blue paint or green paint is applied
• Blue paint or green paint is applied to some screws to prevent them from coming
loose.
• As a general rule, screws to which blue paint or green paint is applied should not be
removed or loosened.
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
CAUTION
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
9
3. OTHER Field Service Ver.2.0 Jan. 2007
10
Field Service Ver.2.0 Jan. 2007 3. OTHER
PC-402
1. Open the Right Door [1].
[1]
[3] 2. Remove the Right Door [1].
[2]
3. Remove two screws [2] and remove the
Rear Right Cover [3].
4. Remove two screws [4] and remove the
Lower Right Cover [5].
5. Remove two screws [6] and remove the
Front Right Cover [7].
[4]
[5]
[7] [6] 4061f2c219na
[2]
[1] 4061f2c220na
11
3. OTHER Field Service Ver.2.0 Jan. 2007
3.3.3 Tray
[2]
[6]
4061f2c222na
CAUTION
• To prevent injuries, press the guide rail
[7] inside the machine.
[7]
4061f2c223na
12
Field Service Ver.2.0 Jan. 2007 3. OTHER
3.3.4 Wire
PC-402
[3] [1] (See P.12)
2. Remove four screws [1] and remove the
Front Cover Assy [2].
3. Unplug the connector [3].
[1]
[2]
4061f2c224na
[5]
[4]
4061f2c225na
[6]
4061f2c226na
[8]
4061f2c227na
13
3. OTHER Field Service Ver.2.0 Jan. 2007
NOTE
• When assembling, be sure to engage
rib of gear 1 [10] with concave section
PC-402
of gear 2 [11].
[10]
[11]
4061f2c228na
[12]
[12]
4061f2c229na
[15]
[16]
[14]
[15]
[14]
4061f2c230na
[18]
[18]
[17]
4061f2c231na
14
Field Service Ver.2.0 Jan. 2007 3. OTHER
PC-402
[20]
[20]
4061f2c232na
[22]
4061f2c233na
[25]
[26]
[24]
4061f2c234na
4061f2c235na
15
3. OTHER Field Service Ver.2.0 Jan. 2007
• The alcohol described in the cleaning procedure represents the isopropyl alcohol.
B. Procedure
1. Remove the Right Door.
[2] (See P.11)
2. Remove two screws [1] and remove the
Paper Separation Roller Mounting Plate
Assy [2].
[1]
4061f2c236na
4061f2c237na
B. Procedure
1. Remove the Tray.
[1] 2. Remove the Separation Roller Mounting
Plate Assy.
(See P.16)
3. Using a soft cloth dampened with alco-
hol, wipe the Feed Roller [1].
4061f2c238na
16
Field Service Ver.2.0 Jan. 2007 3. OTHER
PC-402
B. Procedure
1. Remove the Tray.
[1] 2. Remove the Separation Roller Mounting
Plate Assy.
(See P.16)
3. Using a soft cloth dampened with alco-
hol, wipe the Pick-up Roller [1].
4061f2c239na
B. Procedure
1. Open the Right Door.
[1] 2. Using a soft cloth dampened with alco-
hol, wipe the Vertical Conveyance
Roller [1].
4061f2c240na
17
3. OTHER Field Service Ver.2.0 Jan. 2007
PC-402
Blank Page
18
Field Service Ver.2.0 Jan. 2007 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT
PC-402
4.1 Mis-centering adjustment
Conduct this adjustment when a mis-centering occurs that cannot be adjusted in the service
mode.
[2]
[1]
4061f3c201na
4061f3c202na
4061f3c203na
4061f3c204na
19
4. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
[2]
between the center [1] of the paper and
[3] the center [2] of the copied image is
within a standard value (± 3 mm or less
[1] [3]).
6. When the value is not within the stan-
dard value, repeat steps 1 to 5 until the
standard value can be obtained.
4061f3c209na 7. Slide out the Tray and tighten the
adjustment screw.
20
Field Service Ver.2.0 Jan. 2007 4. MECHANICAL ADJUSTMENT
PC-402
[2] 2. Lift the Main Tray [1], and remove two
[1] screws [2] fixing the Shift Tray.
NOTE
• When reinstalling, take care not to
unfasten the wire of the Main Tray.
4061f3c205na
[3]
4061f3c206na
[6]
4061f3c207na
4061f3c208na
21
4. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
PC-402
Blank Page
22
SERVICE MANUAL Field Service
LU-201
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
LU-201
LU-201
OUTLINE
1. PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MAINTENANCE
2. PERIODIC CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Maintenance procedure of the paper feed section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1.1 Replacing the pick-up rubber and the feed rubber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1.2 Replacing the separation roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Disassembling and assembling list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Disassembling and assembling procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2.1 Removal and reinstallation of the right cover, the front cover and the rear cover. . . . . . . . . . . . 11
3.2.2 Replacing the wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1 Adjusting the tilt of the lift plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
i
CONTENTS Field Service Ver.1.0 Feb. 2006
LU-201
Blank page
ii
Field Service Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
OUTLINE
LU-201
1. PRODUCT SPECIFICATION
A. Type
B. Functions
C. Type of paper
Paper type *1 Plain paper, recycled paper, high quality paper of 60 to 105 g/m2
Paper size A4, 81/2 x 11
*1 Recommended paper
Plain paper Inch: Hammermill Tidal MP (20 lbs)
Metric: Konica Profi (80 g/m2), Konica Minolta Original (80 g/m2)
Recycled paper Inch: Weyehaeuser Recycled Laser Copy (20 lbs)
Metric: Nautilus (80 g/m2)
D. Maintenance
E. Machine data
F. Operating environment
Note
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATION Field Service Ver.1.0 Feb. 2006
LU-201
Blank page
2
Field Service Ver.1.0 Feb. 2006 2. PERIODIC CHECK
MAINTENANCE
LU-201
2. PERIODIC CHECK
2.1 Maintenance procedure of the paper feed section
Caution
• When connected to the main body, make sure that the power cord of the main body is unplugged
from the power outlet.
B. Procedure
1. Open the upper door [1].
[1]
2. Remove the C-clips [2], 1 each, and release the 2
bearings [3].
3. Remove the paper feed roller unit [4].
[4] 16aaf2c001na
3
2. PERIODIC CHECK Field Service Ver.1.0 Feb. 2006
Note
• When installing the paper feed roller unit, be
sure to insert the shaft [1] into the ring of the
LU-201
[3]
actuator [2].
[4] • When installing the paper feed roller unit, be
sure to install it so that the hook [3] comes
above the lift-up shaft [4].
• When installing the paper feed roller unit, be
sure to insert the shaft [5] securely into the
coupling [6].
16aaf2c002na
4
Field Service Ver.1.0 Feb. 2006 2. PERIODIC CHECK
LU-201
ing [4].
6. Pull out the shaft [5] in the arrow-marked direction
[6] and remove the feed roller [7].
[6] [2]
Note
• Be sure to install the feed rubber [2] so that
the paint mark [3] comes in the opposite
direction of the gear [4].
• When setting the feed rubber, apply alcohol
on the inside of the feed rubber. By doing so,
the feed rubber can be set more easily.
5
2. PERIODIC CHECK Field Service Ver.1.0 Feb. 2006
10. Remove the bearing [1] and then remove the pick-
[3] [1]
up roller [3] from the shaft [2].
[2] 16aaf2c006na
Note
• When setting the pick-up rubber, apply alco-
hol on the inside of the pick-up rubber. By
doing so, the pick-up rubber can be set more
easily.
[2] [1]
16aaf2c007na
6
Field Service Ver.1.0 Feb. 2006 2. PERIODIC CHECK
LU-201
B. Procedure
1. Pull out LU from the main body.
[1] 2. Open the upper door [1].
3. Lift up the paper feed roller unit [2].
4. Remove the 2 screws [3] and then remove the
guide plate [4].
[2]
[2] 16aaf2c009na
7
2. PERIODIC CHECK Field Service Ver.1.0 Feb. 2006
16aaf2c010na
[2] 16aaf2c011na
8
Field Service Ver.1.0 Feb. 2006 2. PERIODIC CHECK
8. Pull out the shaft [2] while pressing the lever [1]
[3] [2] and remove the separation roller [3].
LU-201
[1] 16aaf2c012na
Note
• Be sure to install the separation rubber [2] so
that the paint mark [3] comes in the opposite
direction of the projection [4].
• When setting the separation rubber, apply
alcohol on the inside of the separation rubber.
By doing so, the separation rubber can be set
more easily.
16aaf2c013na
9
3. OTHERS Field Service Ver.1.0 Feb. 2006
3. OTHERS
3.1 Disassembling and assembling list
LU-201
Note
• This list shows the explanation of the disassembly and reassembly of the parts which are consid-
ered necessary to replace (other than periodically replaced parts). However, these parts except for
the covers are not required to be disassembled while in normal service operations.
• For the method of replacing the periodically replaced parts, see "2.1 Maintenance procedure of
the paper feed section".
(See P.3)
10
Field Service Ver.1.0 Feb. 2006 3. OTHERS
LU-201
Caution
• When connected to the main body, make sure that the power cord of the main body is unplugged
from the power outlet.
3.2.1 Removal and reinstallation of the right cover, the front cover and the rear cover
A. Procedure
1. Pull out LU from the main body side.
[1] [2] 2. Open the upper door [1].
3. Remove the 2 screws [2] and then remove the
right cover [3].
Note
• When installing the right cover [3], be sure to
take note of the direction of the 2 casters [4].
[3]
[4] 16aaf2c014na
11
3. OTHERS Field Service Ver.1.0 Feb. 2006
[2] 16aaf2c016na
12
Field Service Ver.1.0 Feb. 2006 3. OTHERS
LU-201
rear cover [4].
10. Reinstall the above parts following the removal
steps in reverse.
[4] [3]
[2]
[1] 16aaf2c017na
13
3. OTHERS Field Service Ver.1.0 Feb. 2006
[4]
[2]
16aaf2c018na
14
Field Service Ver.1.0 Feb. 2006 3. OTHERS
LU-201
[2]
[1]
16aaf2c019na
16aaf2c020na
15
3. OTHERS Field Service Ver.1.0 Feb. 2006
Note
[1] [2] • When removing the LU drive board unit, the
bearings [1] and [2] may come off and fall. Be
LU-201
[4] [3]
16aaf2c021na
[1] 16aaf2c022na
16
Field Service Ver.1.0 Feb. 2006 3. OTHERS
LU-201
[1] 16aaf2c023na
10. Peel off the seal [7] from the detection reel [6].
11. Rotate the detection reel [6] clockwise as seen
from the rear side, and remove the detection wire
[8] from the reel.
C
D
B
A
[3] [5]
[4]
[2]
[1]
16aaf2c024na
17
3. OTHERS Field Service Ver.1.0 Feb. 2006
[1] [1]
pulleys [5].
C
D
[5] [4]
[5]
[4]
16aaf2c025na
14. Remove the E-ring [1] and the drive pulley [2],
then remove the auxiliary wire [3], the wire A [4]
and the wire B [5].
15. Remove the E-ring [6] and the drive pulley [7],
C then remove the detection wire [8], the wire D [9]
D and the wire C [10].
B
A
16aaf2c026na
18
Field Service Ver.1.0 Feb. 2006 3. OTHERS
B. Stringing wires
1. Pass the wire A [1], the wire B [2], the wire C [3]
and the wire D [4] through the lift plate [5].
LU-201
[6] [7] [6] [14] [15] [15]
B C 2. Run the wire A [6] and the wire B [7] through the 2
A A D D
upper pulleys [8] and the 2 lower pulleys [9], and
then through the adjustment part [10].
3. Tighten the 2 upper pulleys [8] with the 2 E-rings
[11] [8] [11] [8] [16] [17] [16] [17] [11].
4. Install the wire stopper [12] to each of the 2 lower
pulleys [9] in the direction as shown in the draw-
ing. And then fasten it with the 2 E-Rings [13].
5. Run the wire C [14] and the wire D [15] through
[4]
C the groove of the pulley [16].
[10] 6. Tighten the 2 pulleys [16] with each of the E-ring
D
[3] [17].
B
A
[2]
[1] [5]
[9] [9]
[12] [12]
[13] [13]
16aaf2c027na
16aaf2c028na
19
3. OTHERS Field Service Ver.1.0 Feb. 2006
9. Hold the drive pulley [1] and the drive pulley [2]
[7] with both hands and rotate them counterclock-
[9] wise as seen from the front side until there are no
LU-201
15. Set the wire attaching notch [2] at the right above
[2] position with no tension applied on the detection
reel [1], and wind the detection wire [3] a full turn
counterclockwise around the detection reel [1]
starting at the top side.
Note
• Be sure to wind the wire from the inside of the
LU to the outside.
[1] [4] [3]
16aaf2c030na
16. Rotate the detection reel [1] clockwise to apply
tension. After rotating about 3/4 turn, install the
detection wire [3].
17. Stick the seal [4] to the detection reel [1].
18. Follow Steps 1 to 10 in “A. Removing the wire” in
reverse order.
Note
• After finishing wire replacement, move the lift
plate up and down to confirm that it moves
smoothly.
• Make sure that the wires do not cross each
other, or a wire does not run on another wire.
• After installing the wires, adjust the tilt of the
lift plate.
(See P.21)
20
Field Service Ver.1.0 Feb. 2006 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
LU-201
4. MECHANICAL ADJUSTMENT
4.1 Adjusting the tilt of the lift plate
When the lift plate is tilted, paper may not be fed correctly. Adjust the lift plate so that it becomes parallel to the
paper feed roller shaft. When replacing the wire, be sure to conduct this adjustment.
A. Procedure
1. Remove the right cover and the front cover.
(See P.11)
2. Loosen the screw [1].
[1] 16aaf3c001na
21
4. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
[1] [3]
16aaf3c002na
22
SERVICE MANUAL Field Service
FS-510/PU-501/
OT-601
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
FS-510/PU-501/OT-601
FS-510/PU-501/OT-601
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
1.1 FS-510 ..................................................................................................................1
1.2 PU-501..................................................................................................................3
1.3 OT-601..................................................................................................................4
MAINTENANCE
2. PERIODIC CHECK..................................................................................................5
2.1 Maintenance procedure ........................................................................................5
2.1.1 Cleaning of the Roller....................................................................................5
3. OTHER ....................................................................................................................7
3.1 Disassembly/Adjustment prohibited items ............................................................7
3.2 Disassembling and assembling list .......................................................................8
3.3 Disassembling and assembling procedure ...........................................................9
3.3.1 Conveyance Front Cover /Up, /Rt, /Lw..........................................................9
3.3.2 Conveyance Upper Cover .............................................................................9
3.3.3 Front Door ...................................................................................................10
3.3.4 Conveyance Front Cover /Lt .......................................................................10
3.3.5 Paper Exit Front Cover, Rear Cover, Connector Cover ..............................11
3.3.6 Tray /2 .........................................................................................................12
3.3.7 OT ...............................................................................................................12
3.3.8 Tray /1 .........................................................................................................12
3.3.9 Lift Tray .......................................................................................................13
3.3.10 Conveyance Unit .........................................................................................13
3.3.11 Stapler .........................................................................................................14
3.3.12 PU ...............................................................................................................15
3.3.13 Stacker Paddle Drive Clutch Assy...............................................................16
3.3.14 Paper Holding Paddle Drive Clutch Assy ....................................................17
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT..............................................................................21
4.1 Staple Position Adjustment .................................................................................21
4.2 Adjustment of the Installation Position of the Shutter Drive Gear .......................22
4.3 Punch Mis-centering Adjustment (PU-501).........................................................23
i
CONTENTS Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
Blank Page
ii
Field Service Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
OUTLINE
FS-510/PU-501/OT-601
1. PRODUCT SPECIFICATIONS
1.1 FS-510
A. Type
B. Functions
Modes Non sort, sort, group, sort staple, and punch (when PU-501 is mounted)
C. Paper type
(1) Non sort
(2) Sort/Group
1
1. PRODUCT SPECIFICATIONS Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
D. Stapling
F. Machine specifications
G. Operating environment
2
Field Service Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATIONS
FS-510/PU-501/OT-601
1.2 PU-501
A. Type
B. Maintenance
C. Machine specifications
D. Operating environment
3
1. PRODUCT SPECIFICATIONS Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
1.3 OT-601
A. Type
B. Paper Type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
4
Field Service Ver.1.0 Feb. 2006 2. PERIODIC CHECK
MAINTENANCE
FS-510/PU-501/OT-601
2. PERIODIC CHECK
2.1 Maintenance procedure
NOTE
• The alcohol described in the cleaning procedure of Maintenance represents the iso-
propyl alcohol.
[1]
4349f2c001na
[2]
4349f2c002na
[4]
4349f2c003na
5
2. PERIODIC CHECK Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[5]
4349f2c004na
[8]
[7]
4349f2c005na
[9]
4349f2c006na
4349f2c007na
6
Field Service Ver.1.0 Feb. 2006 3. OTHER
3. OTHER
FS-510/PU-501/OT-601
3.1 Disassembly/Adjustment prohibited items
A. Screws to which blue paint or green paint is applied
• Blue paint or green paint is applied to some screws to prevent them from coming
loose.
• As a general rule, screws to which blue paint or green paint is applied should not be
removed or loosened.
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
Caution
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
7
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
8
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
3.3 Disassembling and assembling procedure
3.3.1 Conveyance Front Cover /Up, /Rt, /Lw
[1]
4349f2c008na
[2]
[3]
4349f2c009na
NOTE
[5] • At reinstallation, first fit the claw [6]
into position.
[6]
[4] 4349f2c010na
[2]
[1]
4349f2c011na
9
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[1] [3]
4349f2c036na
[1]
4349f2c014na
10
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
3.3.5 Paper Exit Front Cover, Rear Cover, Connector Cover
[6]
[5]
4349f2c038na
11
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
3.3.6 Tray /2
[1] 4349f2c016na
3.3.7 OT
[2]
1. Remove two screws [1], and remove the
OT [2].
[1] 4625f2c001na
3.3.8 Tray /1
[1] 4349f2c017na
12
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
3.3.9 Lift Tray
NOTE
• When removing the Lift Tray, be sure to bring the Tray down to the bottom.
• If the OT is installed, remove it in advance.
4349f2c020na
13
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
3.3.11 Stapler
[2]
4349f2c022na
[4]
4349f2c023na
[5]
4349f2c024na
[7]
4349f2c025na
14
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
3.3.12 PU
[3]
4512f2c002na
[6]
4512f2c003na
[8]
[9]
[8]
4512f2c004na
15
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
A. Removal Procedure
1. Remove the Lift Tray.
(See P.13)
2. Remove the Conveyance Unit.
(See P.13)
[1] 3. Remove the Conveyance Upper Cover.
(See P.9)
4. Remove the E-ring [1].
4349f2c026na
[3]
[2]
4349f2c027na
B. Reinstallation Procedure
[3] 1. Check that the 2-mm hole [2] of the
[1]
stacker paddle drive shaft [1] and the
cutout of the frame [3] are aligned and
[2]
install the Stacker Paddle Drive Clutch
Assy [4].
2. Refer to the figure and check the paddle
position [5].
3. Hook the Solenoid Flapper [7] to the
claw [6] of the Stacker Paddle Drive
Clutch Assy [4].
4. Attach the E-ring and reinstall the
Stacker Paddle Drive Clutch Assy.
5. Adjust the spacing between the E-ring
[5] and the Stacker Paddle Drive Clutch
Assy to 0.2 mm and tighten two hexago-
nal socket head screws.
[4]
[7]
[6] 4349f2c028na
16
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
3.3.14 Paper Holding Paddle Drive Clutch Assy
A. Removal Procedure
[1] 1. Remove the Lift Tray.
(See P.13)
2. Remove the Conveyance Unit.
(See P.13)
[2] 3. Remove the Conveyance Upper Cover.
(See P.9)
4. Remove the C-ring [1].
4349f2c029na 5. Remove the bearing [2].
4349f2c030na
B. Reinstallation Procedure
[1] 1. Reinstall the Paper Holding Paddle
Drive Clutch Assy [1].
4349f2c031na
17
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[2]
[1]
4349f2c032na
[1] Solenoid Flapper [4] Paper Holding Paddle Drive Clutch Assy
[2] 107 ± 3mm [5] Paper Holding Paddle
[3] Paper Holding Paddle
[2]
4349f2c033na
18
Field Service Ver.1.0 Feb. 2006 3. OTHER
FS-510/PU-501/OT-601
4. Attach the C-ring and press the Paper
[5] [6]
Holding Paddle Drive Clutch Assy [6] to
the bearing [5].
5. Adjust the spacing [7] between the
bushing [5] and the Paper Holding Pad-
dle Drive Clutch Assy [6] to 0.2 mm and
tighten two hexagonal socket head
[7] screws.
4349f2c035na
19
3. OTHER Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
Blank Page
20
Field Service Ver.1.0 Feb. 2006 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
FS-510/PU-501/OT-601
4. MECHANICAL ADJUSTMENT
4.1 Staple Position Adjustment
1. Set the staple and make a print.
B [1]
2. Check the staple position of the paper.
A
• Slant one point Staple [1]
C
D (Paper Width: 216 to 297 mm)
279 to 297 mm: 45°,
B5, B4: 30°
Measurement Adjustment
Specification
position range
A, C 4.4 mm —
B, D 12.1 mm +1 to –2mm
A [2]
• Parallel one point Staple [2]
B (Paper Width: 182 to 216 mm)
Measurement Adjustment
Specification
position range
A 4.5 mm —
B 6 mm +1 to –2mm
Y = (paper width–X–11) / 2
X = A3, A4: 137 mm
F 4349f3c001na
B4, B5: 114 mm
A4S: 190 mm
B5S: 162 mm
11 x 17, 81/2 x 11: 119.4 mm
81/2 x 11S: 196 mm
Substitute above into the equation.
21
4. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
[2]
4349f3c002na
4349f3c003na
4349f3c004na
22
Field Service Ver.1.0 Feb. 2006 4. MECHANICAL ADJUSTMENT
FS-510/PU-501/OT-601
4.3 Punch Mis-centering Adjustment (PU-501)
1. Set the copier into the Punch mode and
make a 1-sided print from a 1-sided
original.
2. Fold the output paper in half and check
whether the punch hole positions are
aligned.
4512f3c001na
Specification: 0 ± 2 mm
3. If the punch hole position is misaligned,
adjust with the following procedure.
23
4. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
FS-510/PU-501/OT-601
Blank Page
24
SERVICE MANUAL Field Service
FS-511/RU-502
2006.02
Ver. 1.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
FS-511/RU-502
FS-511/RU-502
OUTLINE
1. PRODUCT SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 FS-511 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 RU-502 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MAINTENANCE
2. OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Disassembling and assembling list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Disassembling and assembling procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.1 Removal/reinstallation of the upper cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.2 Removal/reinstallation of the front cover /Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2.3 Removal/reinstallation of the front cover /Lw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2.4 Removal/reinstallation of the rear cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2.5 Removal/reinstallation of the punch unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.6 Replacing the stapler unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ADJUSTMENT/SETTING
3. MECHANICAL ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1 Output check mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1.1 Switches provided inside the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.1.2 Output check mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2 Adjusting the punch hole position in the vertical direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3 Adjusting the solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3.1 Adjustment of the bypass gate solenoid (SD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3.2 Adjustment of the main gate solenoid (SD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.4 Adjusting the belt tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4.1 Adjustment of the timing belt of the conveyance motor /Up (M4) . . . . . . . . . . . . . . . . . . . . . . . 28
3.4.2 Adjustment of the timing belt of the conveyance motor /Lw (M2) . . . . . . . . . . . . . . . . . . . . . . . 29
3.4.3 Adjustment of the timing belt of the paper exit motor (M3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.5 Adjusting the tray upper surface detection position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.6 Adjusting the tray overload detection level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
i
CONTENTS Field Service Ver.1.0 Feb. 2006
FS-511/RU-502
Blank page
ii
Field Service Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
OUTLINE
FS-511/RU-502
1. PRODUCT SPECIFICATION
1.1 FS-511
A. Type
B. Functions
C. Type of paper
• Maximum load capacity: (80 g/m2) when loaded with paper of the same size.
(1) Straight
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 250 sheets Sub tray —
Recycled paper B5S, A5S, and B6S
Thick paper 51/2 x 81/2S, 81/2 x 11, 91 to 130 g/m2 20 sheets
81/2 x 11S, 81/2 x 14,
Thin paper 50 to 59 g/m2
11 x 17
OHP —
transparencies
Label
Envelope
Label sheet
Letterhead
1
1. PRODUCT SPECIFICATION Field Service Ver.1.0 Feb. 2006
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 50 to 130 g/m2 3000 sheets Main tray —
Recycled paper B5S (A4S or smaller)
Thick paper 81/2 x 11, 81/2 x 11S, 1500 sheets
81/2 x 14, 11 x 17 (B4 or larger)
Thin paper
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 3000 sheets Main tray 50 sheets
Recycled paper B5S (A4S or smaller)
81/2 x 11, 81/2 x 11S, 1500 sheets
81/2 x 14, 11 x 17 (B4 or larger)
(4) Punch
a. Metric/Swedish
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper A3, B4, A4, A4S, B5, 60 to 90 g/m2 — Main tray —
Recycled paper B5S Sub tray
b. Inch 2 holes
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper 81/2 x 11S, 81/2 x 14 60 to 90 g/m2 — Main tray —
Recycled paper Sub tray
c. Inch 3 holes
Type of paper Size of paper Weight Max. capacity Exit tray Max. number of
sheets stapled
Plain paper 81/2 x 11S, 11 x 17 60 to 90 g/m2 — Main tray —
Recycled paper Sub tray
2
Field Service Ver.1.0 Feb. 2006 1. PRODUCT SPECIFICATION
D. Stapling
FS-511/RU-502
Staple filling method Dedicated staple cartridge (5000 staples)
Staple detection Available (near empty: 20 remaining staples)
Staple position *1 Rear: Diagonal 45° 1 point Metric: A3, B4, A4, B5
Front: Diagonal 45° 1 point Inch: 81/2 x 11, 11 x 17
Rear: Diagonal 28° 1 point Metric: B4, B5
Front: Diagonal 28° 1 point Inch: —
Rear: Parallel 1 point Metric: A4S, B5S
Front: Parallel 1 point Inch: 81/2 x 11S, 81/2 x 14
Side: 2 points A4, A4S, A3, B5, B5S, B4, 81/2 x 11, 81/2 x 11S,
81/2 x 14, 11 x 17
Manual staple None
*1 In case of the 1-staple mode, conduct a parallel and a skew adjustment according to the length in the
main scan direction.
Parallel: main scan direction 182 to 216 mm
Diagonal: main scan direction 216 to 297 mm
E. Punch
F. Maintenance
G. Machine data
H. Operating environment
Temperature 10 to 30 °C
Humidity 10 to 80 % RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
3
1. PRODUCT SPECIFICATION Field Service Ver.1.0 Feb. 2006
1.2 RU-502
FS-511/RU-502
A. Type
B. Functions
C. Type of paper
16fat1c001na
D. Maintenance
E. Machine data
F. Operating environment
Temperature 10 to 30 °C
Humidity 20 to 80 % RH (with no condensation)
Note
• The information herein may be subject to change for improvement without notice.
4
Field Service Ver.1.0 Feb. 2006 2. OTHERS
MAINTENANCE
FS-511/RU-502
2. OTHERS
2.1 Disassembling and assembling list
No. Section Part name Page referred to
1 Cover Upper cover P.6
2 Front cover /Up P.8
3 Front cover /Lw P.9
4 Rear cover P.10
5 Punch section Punch unit P.11
6 Staple section Stapler unit P.13
5
2. OTHERS Field Service Ver.1.0 Feb. 2006
4521f2c004na
6
Field Service Ver.1.0 Feb. 2006 2. OTHERS
FS-511/RU-502
4. Loosen 2 screws [4].
5. Loosen the screw [5] and remove the upper cover
[6].
6. Reinstall the above parts following the removal
steps in reverse.
[3] [2]
4521f2c005na
7
2. OTHERS Field Service Ver.1.0 Feb. 2006
[2]
[3] 4521f2c006na
8
Field Service Ver.1.0 Feb. 2006 2. OTHERS
FS-511/RU-502
1. Loosen 2 screws [1] and remove the front cover
[1] /Lw [2].
2. Reinstall the above parts following the removal
steps in reverse.
[2] 4521f2c007na
9
2. OTHERS Field Service Ver.1.0 Feb. 2006
[2] [3]
[4] 4521f2c008na
10
Field Service Ver.1.0 Feb. 2006 2. OTHERS
FS-511/RU-502
When installing the Swedish punch kit G, be sure to remove the existing punch unit and follow the procedure
given below.
B. Procedure
1. Remove the upper cover.
(See P.6)
2. Remove the connector [1].
3. Remove the screws [2] and [3]. After sliding the
punch unit [4] in the arrow-marked direction [5],
remove it in the arrow-marked direction [6].
Note
• The screw [2] is provided with the spacer [7]
and the washer [8]. Be careful that they do not
get lost.
[3] [4]
[2][7][8] 4521f2c009na
11
2. OTHERS Field Service Ver.1.0 Feb. 2006
Note
[9] [13] [14]
FS-511/RU-502
12
Field Service Ver.1.0 Feb. 2006 2. OTHERS
FS-511/RU-502
1. Open the punch scraps box holder [1].
[1]
4521f2c001na
Note
• After replacing the stapler units /Fr and /Rr,
be sure to return these intervals to their origi-
nal widths.
Note
• For each FS unit, 2 stapler units are provided.
[6]
When replacing these 2 stapler units, they are
replaced at the same time. So, be sure to
remove both the covers.
13
2. OTHERS Field Service Ver.1.0 Feb. 2006
[7][8] [9]
[15] [12][13]
14
Field Service Ver.1.0 Feb. 2006 2. OTHERS
FS-511/RU-502
11. Reinstall the above parts following the removal
steps in reverse.
4521f2c029na
15
2. OTHERS Field Service Ver.1.0 Feb. 2006
FS-511/RU-502
Blank page
16
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
FS-511/RU-502
3. MECHANICAL ADJUSTMENT
3.1 Output check mode
3.1.1 Switches provided inside the board
Test switch [1] Dipswitch used for the mode setting of the output check mode. (All settings
are off in the initial condition.)
Output check switch /1 [2] Used to execute the output check mode.
Output check switch /2 [3]
LED1 to 4 [4] Display the conditions while in the output check mode.
17
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
Note
• Before executing the output check mode, be sure to remove the upper cover, the front cover /Up
and the rear cover of FS in advance.
(See P.6, P.8, P.10)
• When removing the covers of FS, be sure to block the light that strikes on the front door sensor
(PS17) and the upper door sensor (PS18).
[1] 4521f3c002na
18
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
body.
2. Set the test switch [1] to the initial condition (all
OFF).
3. Turn ON SW2.
[1] 4521f3c003na
19
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
Output check switch /1 : ON The motor and the solenoid turn ON.
• Entrance conveyance motor (M1)
• Conveyance motor /Up (M4)
• Bypass gate solenoid (SD1)
• Main gate solenoid (SD2)
Output check switch /2 : ON The motor and the solenoid turn OFF.
• Entrance conveyance motor (M1)
• Conveyance motor /Up (M4)
• Bypass gate solenoid (SD1)
• Main gate solenoid (SD2)
Output check switch /1 : ON The motor and the solenoid turn ON.
• Entrance conveyance motor (M1)
• Conveyance motor /Up (M4)
• Conveyance motor /Lw (M2)
• Paper exit motor (M3)
• Bypass gate solenoid (SD1)
• Paddle motor /Up (M15)
• Paper exit roller release motor (M13)
Output check switch /2 : ON The motor and the solenoid turn OFF.
• Entrance conveyance motor (M1)
• Conveyance motor /Up (M4)
• Conveyance motor /Lw (M2)
• Paper exit motor (M3)
• Bypass gate solenoid (SD1)
• Paddle motor /Up (M15)
• Paper exit roller release motor (M13)
20
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
Output check switch /1 : ON
21
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
22
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
Sensor Status LED
1 2 3 4
Main tray upper limit sensor (PS19) Light pass through { { { z
Intermediate conveyance sensor (PS3) Light blocked { { z {
Bypass route conveyance sensor (PS2) Light blocked { z { {
Main route conveyance sensor (PS4) Light blocked z { { {
z : On { : Off
23
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
A. Procedure
1. Set the punch hole mode, and make a copy in the
single sided original -> single sided print mode.
2. Fold the copy exited into two and check the posi-
tion of the punch holes to see if the discrepancy
"A" [1] is 2 mm or less.
3. When "A" is in excess of 2 mm, adjust the punch
hole position in the vertical direction.
[1]
4521f3c004na
24
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
the arrow-marked direction [5] to adjust the posi-
tion of the punch unit [6].
6. Repeat steps 1 and 2 and check the punch holes
to see if the discrepancy "A" is 2 mm or less.
7. When "A" is in excess of 2 mm, repeat steps 3 to
6 until "A" gets inside 2 mm.
[4]
[3] 4521f3c005na
25
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
4521f3c006na
26
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
1. Remove the upper cover.
[1] [2] (See P.6)
2. Remove the front cover /Up.
(See P.8)
3. Loosen 2 screws [1].
4. Move the main gate solenoid (SD2) [2] and tighten
the 2 screws [1] when the length of "A" [3] comes
to the specified value.
Note
• With the plunger of SD2 pressed in the arrow-
marked direction [4] in advance, be sure to
[4] [3]
adjust the clearance with no play.
4521f3c007na
27
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
3.4.1 Adjustment of the timing belt of the conveyance motor /Up (M4)
A. Procedure
1. Remove the upper cover.
[2]
(See P.6)
[4]
2. Remove the rear cover.
(See P.10)
3. Loosen 2 screws [1].
4. Press the timing belt at the center section [2] with
a spring balance [3] from above. And when the
[3] amount of the deflection [4] comes to 4 mm,
tighten 2 screws [1] at the position in which the
scale of the spring balance points to the specified
value "A."
Specified value "A" = 200 ± 100 gf
[1]
4521f3c008na
28
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
3.4.2 Adjustment of the timing belt of the conveyance motor /Lw (M2)
A. Procedure
FS-511/RU-502
1. Remove the upper cover.
[2] [4] [3] (See P.6)
2. Remove the rear cover /Up.
(See P.10)
3. Loosen 2 screws [1].
4. Pull the square hole [3] provided on the convey-
ance motor /Lw mounting plate [2] with the spring
balance [4] and tighten 2 screws [1] at the position
in which the scale of the spring balance points to
the specified value "A."
Specified value "A" = 800 ± 50 gf
[1]
4521f3c009na
29
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
3.4.3 Adjustment of the timing belt of the paper exit motor (M3)
A. Procedure
FS-511/RU-502
[4] [1]
4521f3c010na
30
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
This adjustment is made when replacing the FS control board (FSCB), or the main tray upper limit LED (LED19)
or the main tray upper limit sensor (PS19).
A. Procedure
1. Set the output check mode "Sensor output check
mode."
(See P.17)
2. Rotate VR1 [1] provided on the FS control board
(FSCB) up to the limit counterclockwise.
[1] 4521f3c011na
[2] 4521f3c012na
31
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
[5]
[1] 4521f3c013na
32
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
This adjustment is made when replacing the FS control board (FSCB) or replacing the tray lift motor (M7).
A. Procedure
1. Set the output check mode "Main tray operation
[1]
mode."
(See P.17)
2. Rotate VR2 [1] on the FS control board (FSCB)
counterclockwise up to the limit.
4521f3c014na
33
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
4521f3c015na
[4] 4521f3c016na
34
Field Service Ver.1.0 Feb. 2006 3. MECHANICAL ADJUSTMENT
FS-511/RU-502
6. Remove the paper that was put in step 3 to block
the light and let the light of LED19 pass through.
Note
• When letting the light of LED19 pass through,
the main tray starts to go up. Be sure to con-
duct the following steps 7 and 8 while in the
up drive of the main tray.
[5] 4521f3c017na
35
3. MECHANICAL ADJUSTMENT Field Service Ver.1.0 Feb. 2006
[5] 4521f3c018na
36
SERVICE MANUAL Field Service
SD-502
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
SD-502
SD-502
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
MAINTENANCE
2. PERIODIC CHECK..................................................................................................3
2.1 Maintenance procedure ........................................................................................3
2.1.1 Cleaning of the Rollers ..................................................................................3
3. OTHER ....................................................................................................................4
3.1 Disassembly/Adjustment prohibited items ............................................................4
3.2 Disassembling and assembling list .......................................................................5
3.3 Disassembling and assembling procedure ...........................................................5
3.3.1 Paper Output Tray/Front Cover.....................................................................5
3.3.2 Rear Cover ....................................................................................................6
3.3.3 Upper Cover ..................................................................................................6
3.3.4 Saddle Unit....................................................................................................7
3.3.5 Folding Unit ...................................................................................................8
3.3.6 Stapler Unit....................................................................................................9
3.3.7 Paper Guide Motor (M13)............................................................................14
3.3.8 Folding Roller ..............................................................................................16
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT..............................................................................23
4.1 Fold Skew Adjustment ........................................................................................23
4.2 Center Staple Skew Adjustment .........................................................................24
i
CONTENTS Field Service Ver.2.0 Jan. 2007
SD-502
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
SD-502
A. Type
B. Paper type
C. Maintenance
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
SD-502
Blank Page
2
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
MAINTENANCE
2. PERIODIC CHECK
SD-502
2.1 Maintenance procedure
NOTE
• The alcohol described in the cleaning procedure of Maintenance represents the iso-
propyl alcohol.
[1]
[1]
4511f2c001na
[2]
4511f2c002na
3
3. OTHER Field Service Ver.2.0 Jan. 2007
3. OTHER
3.1 Disassembly/Adjustment prohibited items
SD-502
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
Caution
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
4
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
1 Paper Output Tray Paper Output Tray P.5
2 Front Cover P.5
3 Cover Upper Cover P.6
4 Rear Cover P.6
5 Saddle Unit P.7
6 Unit Folding Unit P.8
7 Stapler Unit P.9
8 Paper Guide Motor (M13) P.14
Others
9 Folding Roller P.16
[3]
[1]
[2]
4511f2c004na
1. Align the cutout and remove the Paper Output Tray [1].
2. Remove two screws [2], and remove the Front Cover [3].
5
3. OTHER Field Service Ver.2.0 Jan. 2007
[2]
[1]
4511f2c005na
1. Remove two screws [1], and remove the Rear Cover [2].
[2]
4511f2c006na
6
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
Connector Cover [2].
[1]
[2] 4511f2c007na
[4]
2. Remove the screw [3], and remove the
[3]
ground terminal [4].
3. Unplug two connectors [5].
[5]
4511f2c008na
[6]
4511f2c009na
4511f2c010na
7
3. OTHER Field Service Ver.2.0 Jan. 2007
[10] 4511f2c011na
[2]
[1]
4511f2c012na
[4]
4511f2c013na
[5] 4511f2c014na
8
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
4511f2c015na
[9]
4511f2c016na
[1]
[3] [2]
4511f2c017na
[7]
[5] [8]
4511f2c018na
9
3. OTHER Field Service Ver.2.0 Jan. 2007
[6]
4511f2c019na
[7]
[10] [9]
[8]
[10]
4511f2c020na
[12]
4511f2c021na
[14]
4511f2c022na
10
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
[16]
4511f2c023na
4511f2c024na
[19]
[18]
4511f2c025na
[20]
21. Remove eight screws [20], and remove
the Lower Cover [21].
[20]
[21]
[20]
[20] 4511f2c026na
11
3. OTHER Field Service Ver.2.0 Jan. 2007
[23] 4511f2c027na
[24]
4511f2c028na
4511f2c029na
[2] 4511f2c030na
12
Field Service Ver.2.0 Jan. 2007 3. OTHER
[3]
3. Loosen three screws [3] of the stopper.
4. Loosen three screws [4] of the Clincher.
SD-502
[4]
[3]
4511f2c031na
[8]
4511f2c033na
[10]
4511f2c034na
13
3. OTHER Field Service Ver.2.0 Jan. 2007
[1]
[3] [2]
4511f2c035na
[10]
[9]
4511f2c037na
14
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
[11]
[12]
[11]
[11]
4511f2c038na
[13]
[14]
4511f2c039na
[16]
[15]
4511f2c040na
[19]
[17]
4511f2c041na
[21]
4511f2c042na
15
3. OTHER Field Service Ver.2.0 Jan. 2007
[2]
[1]
[4]
[3]
4511f2c043na
1. Press the two Paper Guides [1] in and check that they touch the stopper [2] simulta-
neously.
2. Check that pins [4] can be inserted through the positioning holes [3] (3 holes) of the Paper
Guide Sensor Assy.
3. Use two screws to secure M13.
[2]
[1] 4511f2c044na
[3]
4511f2c045na
16
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
[5]
4511f2c046na
NOTE
• Install the Folding Blade Assy in the
direction shown in the left figure.
[B] [A] [A] Front
[B] Rear
4511f2c047na
[7]
[8]
4511f2c048na
NOTE
• Install the gears so that the mark [9]
are aligned to the position shown in
the left figure.
[9]
4511f2c049na
17
3. OTHER Field Service Ver.2.0 Jan. 2007
[12]
4511f2c050na
[14]
[13]
4511f2c051na
[15]
4511f2c052na
NOTE
[19]
• When installing the gear [17] to the
Lower Guide Plate [18], insert the gear
[18] [17] at an angle and take care not to
[17]
break the claws [19].
• Install the Lower Guide Plate as shown
on the left.
4511f2c053na
18
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
[22] [24].
[24]
[23]
4511f2c054na
[25]
4511f2c055na
NOTE
[29]
• When installing the gear [27] to the
Lower Guide Plate [28], insert the gear
[28] [27] at an angle and take care not to
[27]
break the claws [29].
• Install the Lower Guide Plate as shown
on the left.
4511f2c056na
[34]
[33]
4511f2c057na
19
3. OTHER Field Service Ver.2.0 Jan. 2007
NOTE
[36] • When installing the Folding Rollers A,
B and C, be sure to align the direction
SD-502
[35]
4511f2c059na
20
Field Service Ver.2.0 Jan. 2007 3. OTHER
SD-502
• When installing the Folding Rollers /Rt
and /Lt, be sure to install them so that
the mark [37] of the Roller Gear /Rt
provided on the front of the Folding
Unit comes one tooth above the mark
[38] of the Roller Gear /Lt.
• When installing the Folding rollers /Rt
and /Lt, be sure to install them so that
the gear of the Guide Gear /Lt [40]
comes one tooth above the gear of the
Guide Gear /Rt [41] as seen from the
direction of the arrow mark [39].
• When installing the Folding Rollers /Rt
and /Lt, be sure to install them so that
[39] the mark [43] of the Guide Gear /Rt and
the mark [44] of the Sector Gear get
aligned with each other as seen from
[42] the direction of the arrow mark [42].
[41] [40]
[43]
[44]
4511f2c060na
21
3. OTHER Field Service Ver.2.0 Jan. 2007
SD-502
Blank Page
22
Field Service Ver.2.0 Jan. 2007 4. MECHANICAL ADJUSTMENT
ADJUSTMENT/SETTING
4. MECHANICAL ADJUSTMENT
SD-502
4.1 Fold Skew Adjustment
NOTE
Make this adjustment after any of the following procedures has been performed.
• When the Folding Unit has been replaced.
• When skew occurs in the crease.
4511f3c002na
23
4. MECHANICAL ADJUSTMENT Field Service Ver.2.0 Jan. 2007
Make this adjustment after any of the following procedures has been performed.
• When Staple Unit 1 or 2 has been replaced.
• When skew occurs in the position of the center staple.
[2]
4511f3c004na
24
SERVICE MANUAL Field Service
MT-501
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
MT-501
MT-501
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
MAINTENANCE
2. PERIODIC CHECK..................................................................................................3
2.1 Maintenance procedure ........................................................................................3
2.1.1 Cleaning of the Roller....................................................................................3
3. OTHER ....................................................................................................................4
3.1 Disassembly/Adjustment prohibited items ............................................................4
3.2 Disassembling and assembling list .......................................................................5
3.3 Disassembling and assembling procedure ...........................................................5
3.3.1 Rear Cover/Right Door..................................................................................5
3.3.2 Front Cover/Upper Cover/Paper Output Tray ...............................................5
i
CONTENTS Field Service Ver.2.0 Jan. 2007
MT-501
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
MT-501
A. Type
B. Maintenance
C. Machine specifications
D. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
MT-501
Blank Page
2
Field Service Ver.2.0 Jan. 2007 2. PERIODIC CHECK
MAINTENANCE
2. PERIODIC CHECK
MT-501
2.1 Maintenance procedure
NOTE
• The alcohol described in the cleaning procedure of Maintenance represents the iso-
propyl alcohol.
[1]
[1]
[1]
[1]
4510f2c001na
3
3. OTHER Field Service Ver.2.0 Jan. 2007
3. OTHER
3.1 Disassembly/Adjustment prohibited items
MT-501
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
NOTE
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
4
Field Service Ver.2.0 Jan. 2007 3. OTHER
MT-501
1 Rear Cover P.5
2 Front Cover P.5
Cover
3 Upper Cover P.5
4 Right Door P.5
5 Paper Output Tray Paper Output Tray P.5
[3] [2]
1. Remove the screw [1] and remove the
Front Cover [2].
2. Remove the Rear Cover.
(See P.5)
3. Remove the Upper Cover [3].
4. Remove the Paper Output Trays [4].
5
3. OTHER Field Service Ver.2.0 Jan. 2007
MT-501
Blank Page
6
SERVICE MANUAL Field Service
JS-502
( 500/420/360 (
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for
improvement of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the correspond-
ing page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
JS-502
JS-502
OUTLINE
1. PRODUCT SPECIFICATIONS................................................................................1
MAINTENANCE
2. OTHER ....................................................................................................................3
2.1 Disassembly/Adjustment prohibited items ............................................................3
2.2 Disassembling and assembling list .......................................................................4
2.3 Disassembling and assembling procedure ...........................................................4
2.3.1 Upper Cover ..................................................................................................4
i
CONTENTS Field Service Ver.2.0 Jan. 2007
JS-502
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
1. PRODUCT SPECIFICATIONS
JS-502
A. Type
B. Paper type
Inch:
11 x 17, 81/2 x 14,
81/2 x 11, 81/2 x 11S,
Tray 2
51/2 x 81/2S Plain Paper (56 to 90 g/m2) 100 sheets
(Job Tray)
Metric: A3, B4, A4, A4S, B5,
B5S, A5S
C. Maintenance
Maintenance None
Machine service life Same as the main body.
D. Machine specifications
E. Operating environment
NOTE
• The information herein may be subject to change for improvement without notice.
1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
JS-502
Blank Page
2
Field Service Ver.2.0 Jan. 2007 2. OTHER
MAINTENANCE
2. OTHER
JS-502
2.1 Disassembly/Adjustment prohibited items
A. Screws to which blue paint or green paint is applied
• Blue paint or green paint is applied to some screws to prevent them from coming
loose.
• As a general rule, screws to which blue paint or green paint is applied should not be
removed or loosened.
B. Red-painted screws
• Do not remove or loosen any of the red-painted screws in the field. It should also be
noted that, when two or more screws are used for a single part, only one representa-
tive screw may be marked with the red paint.
NOTE
• Do not turn the variable resistors on boards for which no adjusting instructions are
given in ADJUSTMENT/SETTING.
D. Removal of Boards
Caution
• When removing a circuit board or other electrical component, refer to “SAFETY AND
IMPORTANT WARNING ITEMS” and follow the corresponding removal procedures.
• The removal procedures given in the following omit the removal of connectors and
screws securing the circuit board support or circuit board.
• When it is absolutely necessary to touch the ICs and other electrical components on
the board, be sure to ground your body.
3
2. OTHER Field Service Ver.2.0 Jan. 2007
[1]
[2]
4347f2c001na
1. Remove two screws [1], and remove the Upper Cover [2].
4
SERVICE MANUAL Field Service
IC-204
2007.01
Ver. 2.0
Revision history
After publication of this service manual, the parts and mechanism may be subject to change for improve-
ment of their performance.
Therefore, the descriptions given in this service manual may not coincide with the actual machine.
When any change has been made to the descriptions in the service manual, a revised version will be
issued with a revision mark added as required.
Revision mark:
• To indicate clearly a section revised, show 1 to the left of the revised section.
A number within 1 represents the number of times the revision has been made.
• To indicate clearly a section revised, show 1 in the lower outside section of the corresponding
page.
A number within 1 represents the number of times the revision has been made.
NOTE
Revision marks shown in a page are restricted only to the latest ones with the old ones deleted.
• When a page revised in Ver. 2.0 has been changed in Ver. 3.0:
The revision marks for Ver. 3.0 only are shown with those for Ver. 2.0 deleted.
• When a page revised in Ver. 2.0 has not been changed in Ver. 3.0:
The revision marks for Ver. 2.0 are left as they are.
CONTENTS
IC-204
IC-204
OUTLINE
1. PRODUCT SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MAINTENANCE
2. FIRMWARE VERSION UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. DISASSEMBLY / REASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Removal / Installation of Printer key control board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENT / SETTING
4. SERVICE MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Starting and Finishing the Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TROUBLESHOOTING
6. TROUBLESHOOTING THE PRINTING SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.1 Troubleshooting of the print controller and copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Data Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
i
CONTENTS Field Service Ver.2.0 Jan. 2007
IC-204
Blank Page
ii
Field Service Ver.2.0 Jan. 2007 1. PRODUCT SPECIFICATIONS
OUTLINE
IC-204
1. PRODUCT SPECIFICATIONS
A. Type
B. Functions
1 1
1. PRODUCT SPECIFICATIONS Field Service Ver.2.0 Jan. 2007
C. Paper
E. Machine Data
F. Operating Environment
2
Field Service Ver.2.0 Jan. 2007 2. FIRMWARE VERSION UP
MAINTENANCE
IC-204
2. FIRMWARE VERSION UP
Firmware for IC-204 is contained in the copier firmware (MFP Controller).
With the updating of MFP controller version, the version of the IC-204 firmware is also updated.
3
3. DISASSEMBLY / REASSEMBLY Field Service Ver.2.0 Jan. 2007
3. DISASSEMBLY / REASSEMBLY
IC-204
Caution
• Assembly should be made in reverse order of disassembly unless otherwise noted.
Caution
• Be sure to unplug the power cable, not only to turn the copier off, before attempting to make ser-
vicing.
Caution
• Before engaging in Disassembly/Reassembly, check to make sure that all the cables are
unplugged from the copier.
• There may be occasions when boards are damaged if no appropriate grounding measures are
taken. Wear a wrist strap or others during servicing.
• Disassembly/Reassembly should be made on cushioning materials.
4
Field Service Ver.2.0 Jan. 2007 3. DISASSEMBLY / REASSEMBLY
IC-204
the main body, and unplug the power cord from
the outlet.
2. Remove the back cover(6 screws).
Back cover
Board cover
5
3. DISASSEMBLY / REASSEMBLY Field Service Ver.2.0 Jan. 2007
IC-204
Blank Page
6
Field Service Ver.2.0 Jan. 2007 4. SERVICE MODE
ADJUSTMENT / SETTING
IC-204
4. SERVICE MODE
In the service mode, various adjustments / settings are available.
See “10. SERVICE MODE” in Field Service for the main body.
7
5. Starting and Finishing the Service Mode Field Service Ver.2.0 Jan. 2007
IC-204
Blank Page
8
Field Service Ver.2.0 Jan. 2007 6. TROUBLESHOOTING THE PRINTING SYSTEM
TROUBLESHOOTING
IC-204
6. TROUBLESHOOTING THE PRINTING SYSTEM
This table lists information about the symptoms, possible causes, and remedies for problems that may occur
with the printing system (combination of the print controller and copier). It is intended to help engineers find
information as quickly as possible, and provide basic solutions.
Caution
• See the “Copier Service Manual” for information about Error Cord List.
9
7. Data Capture Field Service Ver.2.0 Jan. 2007
7. Data Capture
If any fault is caused in relation with the printer, acquire the print job data for the fault analysis.
IC-204
Capture data of up to 5 jobs can be saved. When new data is saved, oldest one is deleted.
Caution
To enable this function, following conditions should be met.
• Hard disk should have been installed in the main body printer (copier).
• [Administrator Setting] - [Security Setting] - [Security Details] - [Print Data Capture] should be set
to [Allow].
• [Administrator Setting] - [Network Setting] - [FTP Setting] - [FTP Server] should be set to [ON].
10
Field Service Ver.2.0 Jan. 2007 7. Data Capture
IC-204
9. Transfer the data to be captured to PC with the
[get] or [mget] command.
10. Exit from the command prompt.
NOTE
• If you set [Administrator Setting] - [Security
Setting] - [Security Details] - [Print Data Cap-
ture] to [Restrict] after acquiring the capture
data, the job data saved in the hard disk will
be deleted.
11
7. Data Capture Field Service Ver.2.0 Jan. 2007
IC-204
Blank Page
12