Beruflich Dokumente
Kultur Dokumente
LCD-DV Troubleshooting
47" Class Full HD 1080P
LCD TV (47" diagonally)
Preliminary Section:
Contact Information, Preliminary Matters, Specifications,
LCD Overview, General Troubleshooting Steps,
Signal Distribution, Disassembly Instructions and Voltages
Disassembly Section: Removal of Circuit Boards
Troubleshooting Section: Board Operation Troubleshooting of :
• Switch Mode Power Supply
• Inverter Boards Main and Secondary (LED Backlight Drivers)
• Main Board
• Extension Boards
• Ft Control Board
• Soft Touch Keys
• Speakers
Section 1
This Section will cover Contact Information and remind the Technician of Important
Safety Precautions for the Customers Safety as well as the Technician and the
Equipment.
Basic Troubleshooting Techniques which can save time and money sometimes can
be overlooked. These techniques will also be presented.
This Section will get the Technician familiar with the Disassembly, Identification and
Layout of the LCD Display Panel.
At the end of this Section the Technician should be able to Identify the Circuit Boards
and have the ability and knowledge necessary to safely remove and replace any
Circuit Board or Assembly.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for
diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be
aware that many household products present a weight hazard. At least two people should be involved in the
installation or servicing of such devices. Failure to consider the weight of an product could result in physical
injury.
Today’s sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage
the electronics in a manner that renders them inoperative or reduces the time until their next failure.
Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively,
you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before
removing a replacement part from its package, touch the anti-static bag to a ground connection point or
unpainted metal in the product. Handle the electronic control assembly by its edges only. When
repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate
the receiving antenna; Increase the separation between the equipment and the receiver; Connect the
equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the
dealer or an experienced radio/TV technician for help.
LCD-DV: 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, 42SL80,
47LG90, 47LH85, 47LE8500
PLASMA: 42PG20, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK750, 50PS80, 50PS60, 60PK750,
60PS11, 60PS60, 60PS80
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical
damage and part number accuracy.
2. Check the model label. Verify model names and board model matches.
3. Check details of defective condition and history. Example: Oscillator failure dead set, etc…
•Define Look at the symptom carefully and determine what circuits could be causing
the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and
check for possible overheated components. Capacitors will sometimes leak dielectric material
and give off a distinct odor. Frequency of power supplies will change with the load, or listen for
relay closing etc. Observation of the front Power LED may give some clues.
•Localize After carefully checking the symptom and determining the circuits to be
checked and after giving a thorough examination using your senses the first check should
always be the DC Supply Voltages to those circuits under test. Always confirm the supplies
are not only the proper level but be sure they are noise free. If the supplies are missing check
the resistance for possible short circuits.
•Isolate To further isolate the failure, check for the proper waveforms with the
Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing
and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes
“glitches” or “road bumps” will be an indication of an imminent failure.
•Correct The final step is to correct the problem. Be careful of ESD and make sure to
check the DC Supplies for proper levels. Make all necessary adjustments and lastly always
perform a Safety AC Leakage Test before returning the product back to the Customer.
Media Box
TV A/V Inputs
Wireless Receiver/Transmitter
“Dongle”
Attaches via Velcro to
the back of the set
HDMI
Invisible Speaker
Personally tuned by Mr. Mark Levinson for LG
TAKE IT TO THE EDGE newly introduces ‘Invisible Speaker’ system,
guaranteeing first class audio quality personally tuned by Mr. Mark
Levinson, world renowned as an audio authority. It provides Full Sweet
Spot and realistic sound equal to that of theaters with its Invisible
Speaker.
Dual XD Engine
Realizing optimal quality for all images
One XD Engine optimizes the images from RF signals as another XD
Engine optimizes them from External inputs. Dual XD Engine presents
images with optimal quality two times higher than those of previous
models.
Wireless Ready
Wireless 1080p Connectivity lets you cut loose from messy wires and
still get a stunning Full HD picture. Disclaimer: Wireless media kit
required and sold separately.
Picture Wizard
Get easy self-calibration with on-screen reference points for key picture
quality elements such as black level, color, tint, sharpness and
backlight levels. Take the guesswork out of picture adjustments with
this simple-to-use feature. It's not actually magic, but it will sure seem
that way.
Seamless Design
You'll love the stunning picture while it's on and marvel at its
appearance while it's off. The display is a seamless, edge-to-edge
panel of glass over an ultra-slim, almost unnoticeable bezel. It's a
sleek, elegant, virtually border-free design that will appeal to even the
most refined sense of style.
TruMotion 240Hz
See sports, video games and high-speed action with virtually no motion blur and
in crystal clarity with LG’s TruMotion 240Hz technology. Now your TV can keep
up with the fastest moving scenes.
MKJ39170828
105-201M
LAN USB 2
USB 1
Component or
Composite
Video/Audio 3
Head
Wireless Media Box Phones
Remote Jack
MAIN BOARD
Rear and Side
Input/Output locations HDMI 4
Software
Version
found on the
USB Flash
Drive
File found
on the USB
Flash Drive
Prepare the Jump Drive as described in the “USB Automatic Download” section and insert it into either of the USB ports.
Bring up the Customer’s Menu and scroll to “OPTIONS”.
Press the “FAV” key 7 times to bring up the Manual Download Screen.
WARNING:
Use extreme Caution
when using the
Manual “Forced”
Download Menu. Any
file can be
downloaded when
selected and may
cause the Main board
to become inoperative
Example of files found if the incorrect file
On the Jump Drive was selected.
Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G.
This means that when PCM is OK, PCM audio is priority and when AC3 is OK, AC3 audio is
priority.
Wattage 1.3/8"
Local Dimming 90W There must be at least 4 inches of Clearance on all sides 106.68mm
Full White 130W
Stand By 0.1W 44.3/16"
1122.68mm
8.7/16"
19.5/16" 214mm
490mm
7.7/8"
200mm
27.13/16" Model No.
706.43mm Serial No. 7.7/8"
Label 200mm
Center
30.3/16"
767.08mm
13.15/16"
353.22mm 11.5/8"
295mm
Remove 4 screws to
remove stand for
wall mount
2.3/8" (60.32mm)
27
July 2010 47LE8500 LCD-DV
DISASSEMBLY SECTION
Disassembly:
This section of the manual will discuss Disassembly, Layout
(Circuit Board Identification) of the 47LE8500 LCD Direct View Television.
Inverter
Secondary
Inverter
Main
Power Supply
(SMPS)
Main Board
LVDS Cables
CON3
IR Soft Touch Keys Speaker (Front Right) LED Speaker (Front Left)
p/n: EBR64966401 p/n: MES61858301 p/n: EAB60961501 p/n: EAV60793306 p/n: EAB60961501
Press in gently on
the two tabs
Disconnect to release lock
P201, P205,
P204 and AC
SK101 fits very
In SK101. snug into it’s
connector.
Remove the 6
screws indicated
by the arrows.
Press in on the
AC In two tabs
to release lock
SK101
0 P7901
Disconnect P7500, 90 P7500 P7501
P7
P7501, P7900, P7901, P8000
P8000, P8200 and P8800
Press in on the
Remove any tape holding top and bottom
down any cables. release tabs to
Remove the 7 screws N/C remove.
indicated by the arrows.
Decorative
Remove decorative N/C Metal Plate
plastic and remove the
board. After removing the Main, there
are tabs sticking through the
Main board holding the Metal
plate in place.
NOTE: Always check on
top and behind the Large
ICs. And look for a piece P8800 P8200
of Chocolate
(Heat Transfer Material).
Be sure to transfer to
new Board if present.
CN11 CN5
NOTE: If Servicing the Board, leave the
screws installed to provide stability and
grounding.
N/C
CN103 CN105
NOTE: If Servicing the Board, leave the
screws installed to provide stability and N/C
grounding.
Tab Tab
N 2
CO
CON3
IR board / Intelligent Sensor
CON1
Troubleshooting:
This section of the manual will discuss troubleshooting.
F101
3.15A/250V
STBY 2.9V
Run 393.3V
From Hot Gnd
F501
3.15A/250V
STBY 159.6V
Run 392.6V
From Hot Gnd
F100
6.3A/250V
AC Protect
Hot Ground
Shock
Hazard
Extension
P205
A (Right)
24V Inverter
Board
Stand-By 159.6V 6 Secondary
1 Run 392.6V (Hot Gnd) 8
9 CN103 CN104 CN25~CN33
24V B+ for the Inverters P
Bridge No AC Det in To Panel Backlights
DIM
this model 6 CN3~CN11
5 Inverter On P204 24V CN1
Extension Extension
B (Cent) A (Left)
12V/24V CN2
Board
Stand By 6
3.5V Reg Regulators Starts the Inverters Inverter Main
8 INV
P201 9
CN11 CN3
Board
P On
Stand By 12V 24V Cust Menu for DIM CN14~CN22
3.5V P Backlight
At point 3 TV is in and P-DIM
Stand-By state. DIM Global Dimming
Inv Picture Content
Energy Star compliant. Manipulate P-DIM
0 .1 Watts RL_ON On To Panel
Backlights
2 5 6 6 8 9 PWM-DIM Digital
120Hz
Dimming
Manipulates
24V 8 IC9301
P8000 P7901 Backlight LEDs
Audio IC9302 Dimming
3.5V_ST Low = Bright
Inverter On
P-DIM
12V Video 1.8V IC 10 MOSI, CLK
2 MAIN Processing
Dimming
Local
P7900
BOARD
RL_On
(1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC.
This will turn on the power supply, relays will click.
a) Check that the 24V and 12V power supplies are turned on,
• P201 (12V pins 17, 19 and 21)
• P201 (24V pins 2, 3 and 4)
• P204 and P205 (24V pins 1 through 5) to the Inverters
Backlights Normal:
a) If normal, the backlights should turn on.
SMPS OK, Inverter OK. Pin 1 is the
Brown Wire
Backlights Abnormal:
a) Recheck all connections.
b) Confirm the INV On/Off line pulling up to at least 3V and arriving at both Inverters.
c) Check the connections to the Inverters.
If the 24V and the Inverter On command is arriving at the Inverters in, then see Inverter Section
for further testing.
Note: Either Inverter can run separately.
REMOVE AC POWER:
Diode
Pin Label STBY Run
Check
1 PWR-ON 0V 3.3V 1.68V
2-4 24V 0V 24.6V 0.424V
5-8 GND GND GND GND
9-12 3.5V 3.45V 3.44V Open
13-15 Gnd Gnd Gnd Gnd
16 n/c n/c n/c Open 1
17 12V 0V 11.9V 1.39V Odd pins are on front row
18 INV-ON 0V 2.92V Open
19 12V 0.42V 11.9V 1.39V
(1)
20 P-DIM 0V 0.37V~3.3V Open (1) PDIM Pin 20 can vary according to incoming video IRE
level, OSD Backlight setting and then Intelligent Sensor
21 12V 0V 11.9V 1.39V
(room light condition) Output from the Video Processor
22 n/c n/c 0V Open IC900. Range 0.37V to 3.3V.
.
23 n/c n/c 0V Open
24 ERROR 0V 0V Open
P204 1 P205
1
P204 "SMPS" to CN14 “Inverter Main" P205 "SMPS" to CN201 “Inverter Secondary"
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
1-5 24V 0V 24.6V 0.424V 1-5 24V 0V 24.6V 0.424V
6-10 GND GND GND GND 6-10 GND GND GND GND
(1) (1)
11 P-DIM 0V 0.37V~3.3V Open 11 P-DIM 0V 0.37V~3.3V Open
(2) (2)
12 I-C 0V 2.92V Open 12 I-C 0V 2.92V Open
13 n/c n/c n/c Open
14 ERROR 0V 0V Open
(1) PDIM Pin 20 can vary according to incoming video IRE level, OSD
Backlight setting and then Intelligent Sensor (room light condition)
Output from the Video Processor IC900. Range 0.37V to 3.3V.
SK101 "SMPS" to AC IN
F100
Bottom
Right of
SMPS
F100 (Diode Check)
L N Main Power Switch Closed
SK101
F501
F501
3.15A/250V
Inverter (Main) has 4 Connectors CN2~CN5 that connect to Extensions boards. The Left hand
Extension board (as viewed from the rear) connects to CN2 and CN3 and the Center Extension
board connects to CN4 and CN5.
Inverter (Secondary) has 2 Connectors CN104~CN105 that connect to the right hand Extension
board (as viewed from the rear) which connects to CN23 and CN24.
Each Extension board has 9 connections to the Backlight LEDs.
There are 4 LEDs per/block, 216 Blocks, 8 Blocks per/cartridge, 3 Cartridges per/bar, 9 bars
(rows), 32 LEDs per/cartridge, 96 LEDs per/bar. With a total of 864 LEDs.
Cartridge
Bar
Cartridges
Removed
Cartridge
Cartridge
There are 3
Cartridges per/bar.
Bar
LED
Lens (Reflector)
White Sheet
Light Uniformity
CN1 CN23
CN21 CN32
V81~V88
V33~V40 V113~V120
CN10
CN20 CN31
CN9
V1~V8
V41~V48 V121~V128
CN12 CN30
CN8
V9~V16
V49~V56 V29~V136
CN19
CN2 CN24
CN13
CN7
V17~V24
V57~V64 V137~V144
CN29
CN18
CN17 CN28
CN6
V25~V32
V65~V72 V145~V152
CN16 CN27
CN5
CN15 CN26
CN4
V41~V48
V81~V88 V161~V168
CN25
CN3 CN14
V49~V56
V89~V96 V169~V176
10 9 8 7 2 1
12 11 6 5 4 3
13 1. Case-Top Ass’y
2. TFT Panel Ass’y
3. Guide Panel
4. Sheet DBEFD
5. Sheet Prism U
6. Sheet Prism L
7. Sheet Diffuser L
8. Plate Diffuser
9. Cartridge Ass’y
10. Cover Bottom
11. Driver Boards (2)
12. Extension Boards (3)
13. FRC
Flexible Ribbon Cables
CN1
CN3 CN2
C98
A0950 - 24.6V
Q16 1050 C
Q1 C + F1 U8
E B B E 24.6V 12A/65V
Q4
C U6 U5 CN4
Q2 U13
C 12.96V 13V
B E INVERTER (MAIN)
Q5 BOTH INVERTERS
L101
p/n: AFB72950101
C75
U7
U101 A0950 - 13V POWER
Gnd 1050 C SUPPLY
+
For CN2 / CN3 U4
Q10 13V
C U11
U3
B E 13V POWER Q11
SUPPLY C Q15
Q7 For CN4 / CN5 B
B E C
E
3.3V
L102 U1
U103 U501 U10
L103
12.77V
13V
CN5
E 3.46V
Q3 C B
U102
Q8 Q12 DO NOT 8Mhz 8Mhz
MEASURE CN11 Y501 Y1
C89
A0948 - U9
1050 C
+
13V
Q108 C L207
F101 E Q12
Q109 C B
B E
3.4V U13
12A/65V E Q3 U2
C
+
B
-
U5
C101 E
C B
CN101 Y501
Q103
1050 C
A0948
C151 8Mhz
Q101
E
C B
E 13V
C 12.8V Q501 U4
Q102 B
B CN105
C
+
E
-
U501
Q105
L206
CN1
CN3 CN2
A A
A0950 - 24.6V
Q16 1050 C
Q1 C + F1 U8 To CN 12
E B B C98 12A/65V U6
E
Q4 24.6V Extension Cent
C U5 B CN4 CN4 B+ for
Q2 12.96V 13V
U13
LED Blocks.
C A A Pins 11~12, 21~22,
B E 31~32, 41~42
L101
Q5 INVERTERS (MAIN)
U7
U101 A0950 -
Gnd 1050 C
DC to DC +
Driver C75 U4
Q10 13V
C
U3 U11
B E
Q11
C Q15
Q7 B
B E C
E
3.3V To CN 13
DC to DC U103 Extension Cent
12.77V 13V U10
Driver L103 CN5 B+ for
B B B CN5 LED Blocks.
E
C B Q3 3.46V U501 U1 Pins 9~10,
L102 Q12 19~20, 29~30,
U102
Q8
CN11 39~40, 49~50.
C89
A0948 - U9
1050 C
+
13V
Q4 Q5 Q7 Q8
1 18.3V 1 5V 1 18.1V 1 5V A 12.92V For Main Extensions Board A (Left Side). To Connectors CN2 and CN3.
2 24.6V 2 12.9V 2 24.6V 2 12.8V B 12.92V For Main Extensions Board B (Center). To Connectors CN4 and CN5.
3 12.9V 3 Gnd 3 12.8V 3 Gnd
U103 3.3V
DO NOT
MEASURE
Q108 C L207
E Q12
Q109 B E
24.6V
C B 3.4V U13
E Q3 U2
C To CN 23
+
F101 B
-
Gnd
U5
C101 E C151
C B
CN101 C
Q103
1050 C
A0948
Q101 U501
E
C B To CN 24
E 13V
Q102 Q501 U4 Extension Right
C B 12.8V
+ B
C
C CN105 B+ to LED Blocks pins
E
-
1~2, 11~12,
Q105
L206 21~22,31~32, 41~42.
13V
U3
N/C CN103
Q105 Q106
1 18.15V 1 5V C 13V For Secondary Extensions Board (Right Side) Connectors. To Connectors CN23 and CN24.
2 24.6V 2 12.8V
3 12.8V 3 Gnd
2
Each of the Pin
numbers for the
Components listed
Q5, Q8 or Q106 Pin 3 is Ground
above are the same.
1 3
F1
12A/65V
Top Left of the Board
Just to the right of CN101 Connector Inverter (Secondary)
F101
12A/65V
Y501 Y1
Inverter (Main) Use Top Leg
8Mhz
Inverter (Secondary)
Y501
CN11 “Inverter Main” to “Main” P7900 CN103 “Inverter Secondary” to “Main” P7901
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
1 L_VS 0V 0.05V Open 1 R_VS 0V 0.04V Open
2 M0_MOSI 0V *0.04V~3.26V Open 2 GND GND Gnd GND
3 M0_SCLK 0V 0.23V Open 3 M2_MOSI 0V *0.04V~3.2V Open
4 GND GND GND GND 4 M2_SCLK 0V 0.23V Open
5 M1_MOSI 0V *0.04V~3.26V Open 5 Gnd Gnd Gnd Gnd
6 M1_SCLK 0V 0.23V Open 6 n/c 0V 0V Open
7 GND GND GND GND 7 n/c 0V 0V Open
8 S_CS_N 0V 2.6V 1.65V 8 Gnd Gnd Gnd Gnd
9 S_MOSI 0V *0.18V~0.28V 1.61V *Black to White
10 S_SCLK 0V 2.99V 1.62V
*Black to White
P8100
n/c
Component
These connectors
LAN are Mini plug type
Wireless Remote
P8800
To Speakers
P8200 To Front IR
SW1000
Videoprocessor
Reset
Micro MAIN BOARD 54Mhz X1001
Q8800 IC8004 p/n: EBU60842601 USB2
IC8800
IC700
HDMI IC300
IC8801 Select TU700
Q300
TDVJ-H031F
IC8300 18. IF p
L8804 L8805 Digital Video 17. IF n
16. IF AGC
15. Reset
14. 3.3V
13. 1.26V
12. GND
Q? 11. CVBS
Q8201
Q8700
10. NC
Analog Video 9. SIF HDMI
8. NC
Q8200 7.
6.
SDA
SCL
5. NC
4. NC
3. 5V
2. NC
1. NC Q8306
P8200
P8800 Q8307
IC300 Earphone Amp IC700 (+1.26V_TU) IC8002 (D1.8V) IC8005 (+3.3V_NORMAL) IC8902 (+1.26V_MEMC) IC9102 DC to DC
Pin Pin Regulator Pin Regulator Pin Regulator Pin Regulator Pin HVDD T-CON
[1] 0V [1] 0V (Gnd) [1] 5V [1] 0V (Gnd) [1] 0V (Gnd) [1] 0V (Gnd)
[2] 0V [2] 1.26V (Out) [2] 3.34V (In) [2] 11.8V (In) [2] 11.8V (In) [2] 11.72V (In)
[3] 0V [3] 3.3V (In) [3] 1.8V (Out) [3] 0V (Gnd) [3] 0V (Gnd) [3] 11.72V (In)
[4] 0V [4] Gnd [4] 0.8V [4] 0.8V [4] 3.25V
[5] 0V IC1000 SOC Reset [5] Gnd [5] 0.86V [5] 0.7V [5] 3.2V
[6] 3.3V Pin Generator [6] 0.9V [6] 3.36V (PWR On/Off2 Ctl) [6] 3.36V (PWR On/Off2 Ctl) [6] 0V
[7] 3.3V [1] 3.32V (In) [7] 0.9V [7] 3.36V (Out) [7] 1.3V (Out) [7] 0V
[8] (-1.8V) [2] 0V (Gnd) [8] 1V [8] 3.36V (Out) [8] 1.3V (Out) [8] 11.7V
[9] (-0.8V) [3] 3.3V (Out) [9] 2.38V [9] 0V (Gnd)
[10] Gnd [10] 3.36V (PWR On/Off1 Ctl) IC8007 Power Det Gen IC8903 (+3.3V_MEMC) [10] 1.13V
[11] 0.9V IC8000 5V Regulator Pin (+12V and +3.5V) Pin Regulator [11] 0V (Gnd)
[12] 1.8V Pin for USB IC8003 (+5V_NORMAL) [1] 0V (Gnd) [1] 0V (Gnd) [12] 0V (Gnd)
[13] 3.3V [1] 11.79V (In) Pin Regulator [2] 3.6V (In) [2] 11.8V (In) [13] 0V (Gnd)
[14] 3.3V [2] 5V (Out) [1] 0V (Gnd) [3] 3.5V (Out) [3] 0V (Gnd) [14] 7.7V
[15] Gnd [3] 5V (Out) [2] 11.8V (In) [4] 0.8V [15] 7.7V (HVDD)
[16] 0V [4] 10.5V [3] 0V (Gnd) IC8008 Power Det Gen [5] 0.8V [16] 0V (Gnd)
[5] 3.3V [4] 0.8V Pin (+24V) [6] 3.36V (PWR On/Off2 Ctl)
IC301 Switched [6] 0.8V [5] 0.86V [1] 0V (Gnd) [7] 3.3V (Out) IC9300 Reset for
Pin 5V for USB 2 [7] 4.99V [6] 3.37V (PWR On/Off2 Ctl) [2] 3.6V (In) [8] 3.3V (Out) Pin LG5111
[1] Gnd [8] 0V (Gnd) [7] 5V (In) [3] 3.7V (Out) [1] 3.32V (In)
[2] 5V (In) [8] 5V (In) IC9100 P-GAMMA [2] 0V (Gnd)
[3] 5V IC8001 D1.2V and A1.2V IC8800 (+1.8V_AMP) Pin Chip [3] 3.34V (Out)
[4] 3.3V Pin Regulator IC8004 A2.5V Regulator Pin Regulator [1] 3.3V
[5] 3.3V [1] 0V (Gnd) Pin for USB [1] 0V (Gnd) [2] 0V (Gnd) IC9302 (1.8V_L/Dimming)
[6] 5V (Out) [2] 3.3V [1] n/c [2] 1.8V (Out) [3] 3.3V (In) Pin Regulator
[7] 5V (Out) [3] 0V (Gnd) [2] 3.26V (In) [3] 3.295V (In) [4] 0V (Gnd) [1] 0V (Gnd)
[8] n/c [4] 1.2V [3] 3.26V (In) [5] 6.8V [2] 11.8V (In)
[5] 3.3V [4] n/c IC8901 (+1.5V_MEMC) [6] 6.8V [3] 0V (Gnd)
IC302 Switched [6] n/c [5] n/c Pin Regulator [7] 15.3V [4] 0.8V
Pin 5V for USB 1 [7] 4.46V [6] 2.55V (Out) [1] 0V (Gnd) [8] 15.3V [5] 0.76V
[1] Gnd [8] 3.3V [7] 0.8V [2] 1.5V (Out) [9] n/c [6] 3.34V (PWR On/Off2 Ctl)
[2] 5V (In) [9] 3.3V [8] 0V (Gnd) [3] 3.3V (In) [10] 13.47V [7] 1.8V (In)
[3] 5V [10] 3.3V [11] 12.75V [8] 1.8V (In)
[4] 3.3V [11] 1.2V Q8005 INV_ON Q8306 HDMI [12] 11.8V
[5] 3.3V [12] Gnd Pin Driver Pin Det [13] 10V D9101 VGH/VDD
[6] 5V (Out) [13] 3.3V B 0V (INV ON) En B 0V [14] 5.96V Pin Rectifyer
[7] 5V (Out) [14] 0.8V C 3.1V (Out) C 3.3V [15] 4.06V A 15.4V
[8] n/c E Gnd E Gnd [16] 15.3V AC 22.2V
[17] 0V C 27.4V (VGH)
Q300 Earphone Mute Q8003 PANEL_VCC Q8200 IR Buffer Q8307 HDMI [18] 2.96V
Pin L Out Pin Control 2nd Driver Pin 2nd Pin Det [19] 2.33V D9102 VGL/VCC
B 0V B 0.679V B 0.02V B 0V [20] 3.3V (In) Pin Rectifyer
C 3.3V C 0V C 3.4V C 4.18V A (-5V VGL)
E Gnd E Gnd E Gnd E Gnd AC (-1.9V)
C 0V
Q8001 PANEL_VCC Q8004 PANEL_VCC Q8201 IR Buffer Q8700 Wireless PWR Q8800 AMP_MUTE
Pin Control 1st Driver Pin Switch Pin 1st Dongle Out Turns on Q8701 Pin Pin 25 IC8801
B 0V S 11.8V (In) B 0V B 0.66V (0.0V Dongle In) B 0V
C 0.68V G 1.8V (Enable) C 3.3V C 0.14V (24V Dongle In) C 3.336V
E Gnd D 11.8V (Out) E Gnd E Gnd E Gnd
B E A1 A2 Rubber
Q8002 IC9101
3 1 Rubber
2
Q8000
IC9303
IC9000
IC602
IC606 IC604
IC8100
Q901
D8312
D S
G B
Q8308
Q200
D S
TU700 G
Rubber
TDVJ-H031F
18.
17.
IF p
IF n Rubber Q8304
16. IF AGC IC8400 Q8301
15. Reset
14.
13.
3.3V
1.26V
IC8200
12.
11.
GND
CVBS
Q702 D8307
10. NC
9. SIF Q8303 Q8300
8.
7.
NC
SDA
D8309
6. SCL
Q701 IC8401
5. NC Q8701
4. NC Q8305 Q8302 IC8700
3. 5V
2. NC
1. NC D8306 Q8205
Q8203
IC602 D1.8V IC8400 RGB IC8700 Wireless Q200 (1.8V_HDMI) Q8203 IR Wireless Pass
Pin Regulator Pin H/V Sync Pin Buffer Pin Switch Pin 2nd Driver
[1] 0V (Gnd) [1] 1.9V [1] 0V (3.3V Dongle In) S 1.83V (Out) B 0V
[2] 3.29V (PWR On/Off1 Ctl) [2] 1.9V [2] 3.3V (0.3V Dongle In) G 3.35V (PWR On/Off2 Ctl) C 3.3V
[3] 0.9V (DDR_VTT) [3] 4.4V [3] n/c D 1.83V (In) E Gnd
[4] 0.93V [4] 0V [4] n/c
[5] 1.83V [5] 0.9V [5] n/c Q701 Tuner SIF
[6] 3.38V (In) [6] n/c (4.5V) [6] Gnd Pin (Sound) Buffer Q8205 IR Wireless Pass
[7] 1.8V (Out) [7] 0V (Gnd) [7] Gnd B 0.16V Pin 1st Driver
[8] 0.91V (DDR_VTT) [8] n/c (4.5V) [8] Gnd C Gnd B 0.6V
[9] n/c (1.9V) [9] n/c E 0.83V C 0V
IC8100 EEPROM [10] n/c (1.9V) [10] 0.02V E Gnd
Pin Micro [11] n/c (4.5V) [11] 0V Q702 Tuner Video
[1] 0V (Gnd) [12] 0.9V [12] 3.3V Pin (Analog) Buffer Q8300, 2 HDMI 2
[2] 0V (Gnd) [13] 0.9V [13] 0V (3.3V Dongle In) B 2.05V Pin Det
[3] 0V (Gnd) [14] 5V [14] 3.3V C 2.75V B 4.2V
[4] 0V (Gnd) [15] 3.3V E Gnd C 0V
[5] 3.37V IC8401 EDID Data [16] 3.3V E Gnd
[6] 3.37V Pin PC Q901 FLASH_WP
[7] 0V (Gnd) [1] 0V (Gnd) IC9303 EEPROM Pin for IC901 Q8303, 4, 5 HDMI 3
[8] 3.37V [2] 0V (Gnd) Pin for LG5111 B 0V (Flash_WP) Pin Det
[3] 0V (Gnd) [1] 0V (Gnd) C 3.36V B 0V
IC8200 RS232 [4] 0V (Gnd) [2] 0V (Gnd) E Gnd C 4.2V
Pin Routing [5] 0.7V [3] 0V (Gnd) E Gnd
[1] 0V [6] 4.1V [4] 0V (Gnd) Q8000 RL_ON (PWR_On)
[2] 0V [7] 4.5V [5] 3.37V Pin 1st Driver Q8308 CEC Remote
[3] 0V [8] 4.5V (In) [6] 3.37V B 0.66V Pin HDMI CEC
[4] 0V [7] 3.34V C 0V [B] 2.72V
[5] 0V IC9000 Serial Flash [8] 3.37V (In) E Gnd [G] 2.73V
[6] (-5.47V) Pin T-CON [S] 3.27V
[7] n/c (5.59V) [1] 0.06V Q8002 PWR_ON [D] 3.37V
[8] n/c (0V) [2] 0.67V D8306, 7, 9 5V Pull Up Routing Pin Switch
[9] n/c (3.3V) [3] 3.3V (In) Pin HDMI SCL/SDA [1] 3.36V (In) Q8701 IR Wireless Pass
[10] n/c (0.2V) [4] 0V (Gnd) A1 5.04V [2] 0V Pin 2nd Driver
[11] n/c (3.3V) [5] 0V C 4.58V [3] 3.3V (Out) G 24.5V (2.3V Dongle I
[12] 3.35V [6] 0.34V A2 0V S 24V
[13] 0V [7] 3.31V (In) D 0V (24.5V Dongle In)
[14] (-5.47V) [8] 3.34V (In) D8312 3.5V Pull Up
[15] 0V (Gnd) Pin HDMI CEC
[16] 3.37V A1 0V
C 3.26V
A2 3.2V
Runs when
set is On
4.86V p/p
1.6V 1.6V
3.27V p/p
25Mhz 12Mhz
Runs when
set is On
X9001
X9000
MAIN Board
2.26V p/p
1.52 1.3V
789mV p/p
Either leg 10Mhz 54Mhz
Runs all Runs when set is On
The time
+7.81V
L9100
HVDD
IC9102
Panel 12V
L9104
+16V
VDD B+ for
IC9102
IC9103
L9102
D9101
-5V +3.3V
VGL VCC
D9102
P7501 P7500
IC9101
Back Side of Board
-4.7V (VST)
From IC9101 Pin 20
-4.8V (VDD-EVEN)
Diode Mode values taken with OSD Backlight setting and Intelligent Sensor (room light condition).
all Connectors Removed Range 0.37V to 3.3V.
(1) Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p)
(2) IR pulses (1.6V p/p)
P7900 “Main” to “Inverter Main” CN11 P7901 “Main” to “Inverter Secondary” CN103
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
1 L_VS 0V 0.05V 1.08V 1 R_VS 0V 0.04V Open
2 M0_MOSI 0V *0.04V~3.26V 1.08V 2 Gnd Gnd Gnd Gnd
3 M0_SCLK 0V 0.23V 1.08V 3 M2_MOSI 0V *0.04V~3.2V 1.1V
4 GND GND GND GND 4 M2_SCLK 0V 0.23V 1.1V
5 M1_MOSI 0V *0.04V~3.26V 1.08V 5 Gnd Gnd Gnd Gnd
6 M1_SCLK 0V 0.23V 1.08V 6 M3_MOSI 0V 0V 1.1V
7 GND GND GND GND 7 M3_SCLK 0V 0V 1.1V
8 S_CS_N 0V 2.6V 1.08V 8 Gnd Gnd Gnd Gnd
9 S_MOSI 0V *0.18V~0.28V 1.08V
*Black to White
10 S_SCLK 0V 2.99V 1.08V
*Black to White
(1)
P8800
Diode Mode values taken with all Connectors Removed
The Intelligent Sensor and IR board (located on the bottom left as viewed from the rear) contains the
IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also connects with the Soft Touch
Key Board and the Center LG Logo board. The Center LG Logo lights after power on and the picture
appears. Then dims down in about 2 seconds. At power off, it does the reverse.
The IR board receives it operating B+ via CON1 pin 6 (STBY 3.5V).
The IR (Infrared) remote receiver can be measured (1.57V) at pin 9 of connector CON1 or P8200 on
the Main board in Stand-By. During run pin 9 reads (1.54V).
The IR pulses (1.6V p/p) CON1 pin 9 are sent to P8200 on the Main board and on to the
Microprocessor (IC8101) via pin 16.
The Intelligent Sensor communicates with the Micro/Video Processor IC900 BCM Chip via clock and
data lines SCL1 and SDA1 arriving on connector CON1 from P8200 pins 1 and 2 on the Main board.
The Front Power LEDs are controlled by these same Clock and Data lines which communicate with
the LED Driver IC U1 on the Soft Touch Key board.
The Key board is routed to the IR board via CON2 and output on CON1 Key 1 and Key 2 lines, (Key 1
pin 4 and Key 2 pin 5). Arriving at P8200 pins 4 and 5 on the Main Board.
Then to the Microprocessor 25 and 26 lines.
CON1
P100
To Main Board
IR board and Intelligent
Sensor board
Installed
Top View
Side View
Front View
This section shows the 11X17 foldout that’s available in the Paper
and Adobe version of the Training Manual.
+
B
-
(2) Inverters coming from the Main board. If the brightness
CN1 14 ERROR 0V 0V Open
I-C is Inverter On (INV_ON)
returns to normal, the Main board is defective. 24.6V U101 Q106 CN104
24.6V
V33~V40 V81~V88
5 IRE CN21
1050 C
A0950
3.88V p/p 120Hz
C151 U5
C101 Q103
C E
V113~V120 B Y501
1050 C
A0948
Q105 8Mhz
13V
CN10 1 18.15V
C E
Q101 B E CN32
Indicates Hot 2 24.6V C B
12.8V U4
Ground Q102 B
CN105
Q4 / Q7 Q5 / Q8 3 12.8V CN101 Q501 E C
-
L206 U501
1 18.3V 1 5V
2 24.6V 2 12.9V Q106 Q105
V41~V48 V121~V128 CN103 V1~V8
3 12.9V 3 Gnd 1 5V 13V N/C
P204 P201
P205 A1
2 12.8V
U3
SMPS BOARD D201 3 Gnd
Q252
C
CN1 CN20
p/n: EAY60908801
C = 3.45V
A1/A2 = 0V A2 CN3 CN2
C98 CN31
CN9 Q251 Q16 A0950 - 24.6V
Q1 C 1050 C
+ F1 U8
D222 IC103 E B B E Q4 24.6V 12A/65V
A1
C
C U6 U5 CN4 To the Panel
A2
T501 Q2 C 12.96V 13V INVERTER (MAIN)
U13 CN12 V9~V16
V49~V56 T102 T101 A1
C IC502
Q5
A2
B E
L101 Both Inverters SW9300
D221 Tru- P7501 P7500
-
p/n: AFB72950101 U7
F501 U101 Gnd
A0950
0 V29~V136 Motion P7901 P8000
105 C
+ IC9100
3.15A/250V IC501 C75 13V U4 Reset IC9101 IC9102 IC8005
CN8 IC102 C
U3 U11 CN19 P7900 L9100 CN30
Q10 B IC9301 1 3
F101 E
C Q15 LG5111 RX/TX
L9102 Q8005 CN24
3.15A/250V Q7 Q11 B 2
C Q8004 Q8000 Q8002
47uF/450V
47uF/450V
47uF/450V
47uF/450V
47uF/450V
47uF/450V B E E IC9303
Q110 3.3V A IC9103
CN2 Q111 F501 Hot Gnd L102 U501 U1 CN13 D9101 AC D
Q8001 L8015
S
D
G S
D
G STBY 159.6V 12.77V
U103
L103 U10 CN5 C G S
V17~V24
V57~V64 Run 392.6V 13V IC9300 D9102
A AC Q8003 31 31
Rubber
Q3 C E 3.46V SW9300 C
L9101 IC8008
B 2 2
X9300 IC9302
U102 8Mhz 8Mhz IC8007
D102
Q8 Q12 CN11 Y501 Y1
V137~V144 25Mhz L9301 IC8902 L8905
C89 DO NOT
IC9000 IC8903
- MEASURE IC9001
CN7 F101 Hot Gnd
A0948 U9 IC8003 CN29
1050 C
+ 13V CN18 X9000
T-CON IC8901
STBY 2.9V D607 LG7378A IC8900 L8904 IC8002 IC8001
Run 393.3V D101 12Mhz
L8012
L601 Grayed out components
are on the back IC602
P201 "SMPS" To P8000 "MAIN Board" P8000 IC605 IC606 L8009 V25~V32
Q8700
SMPS TEST 1 Supply On.
(1)
PDIM Pin 20 can vary according to incoming video IRE level, V161~V168 Q? D8309 IC8200 13.
12.
1.26V Analog Video
GND
4 M2_SCLK 0V 0.23V 1.1V HDMI
Disconnect P8000 on Main board. OSD Backlight setting and then Intelligent Sensor (room light Q8701 11. CVBS
CN26
STBY 3.5V
IC8700
to pin 1. (Test Voltage Outputs 12V, Range 0.37V to 3.3V. 6 M3_MOSI 0V 0V 1.1V 8. NC
24V 24V
24V to Main and 24V to both CON3 "IR Board" To Q8201 7. SDA
24 22 20 18 16 14 12 10 8 6 4 2 7 M3_SCLK 0V 0V 1.1V Q8205 D8306 6. SCL
P201
Q8307
A
CON3 CN14
PWR ON
A
Intelligent Sensor 2 SDA 3.45V 3.45V Open 8 LED_LOGO 0V 0V Open
PWR ON
Front pins on connector LEDs on the Right (Back View) 2 SPK-R(+) 0V 12.3V Open
are odd numbers. should turn on. CON2 "IR Board" To "Soft Touch Key Board"
3 SPK-L(-) 0V 12.3V Open 3 Gnd Gnd Gnd Gnd 9 IR 1.57V 1.54V Open
Remove AC and Disconnect P205 Pin STBY Run Diode Pin STBY Run Diode
and reinstall P204. When AC is 4 Key1 3.29V 3.29V 1.9V 10 Gnd Gnd Gnd Gnd
1 3.45V 3.36V Open 5 3.28V 3.28V Open 4 SPK-L(+) 0V 12.3V Open
reapplied, the Backlight LEDs on the
2 0V 1.63V Open 6 Gnd Gnd Gnd
5 Key2 3.29V 3.29V 1.9V 11 3.3V_Normal 0V 3.3V 0.59V
Left (Back View) should turn on.
3 Gnd Gnd Gnd 7 3.45V 3.36V Open
Stand-by 6 3.5V_ST 3.45V 3.45V 1.24V 12 LED_BUZZ 0V 0V Open
4 3.3V 3.3V Open 8 3.45V 3.36V Open
42LE8500 Inverter Main and Secondary Local Dimming Control Signals Waveforms
1V per/div 4MSes 3.66V p/p 1V per/div 4MSes 3.70V p/p 1V per/div 4MSes 4.22V p/p 1V per/div 4MSes 3.70V p/p 1V per/div 4MSes 3.96V p/p
Inverter Main CN11 pin 05 Inverter Main CN11 pin 05 Inverter Main CN11 pin 06 Inverter Main CN11 pin 08 Inverter Main CN11 pin 09
Black Screen White Screen Black or White Screen Black or White Screen Black Screen
1V per/div 4MSes 3.66V p/p 1V per/div 4MSes 3.98V p/p 1V per/div 4MSes 3.98V p/p 1V per/div 4MSes 3.76V p/p 1V per/div 4MSes 3.66V p/p
Inverter Main CN11 pin 09 Inverter Main CN11 pin 11 Inverter Main CN11 pin 11
White Screen Black Screen White Screen
1V per/div 4MSes 3.88V p/p 1V per/div 4MSes 3.88V p/p 1V per/div 4MSes 3.68V p/p
Inverter Secondary CN103 pin 01 Inverter Secondary CN103 pin 02 Inverter Secondary CN103 pin 03 Inverter Secondary CN103 pin 04
Black or White Screen Black Screen White Screen Black or White Screen
1V per/div 4MSes 3.52V p/p 1V per/div 4MSes 3.56V p/p 1V per/div 4MSes 3.56V p/p 1V per/div 4MSes 3.62V p/p
47LE8500 MAIN (FRONT SIDE) SIMICONDUCTORS
IC700 (+1.26V_TU) IC8002 (D1.8V) IC8005 (+3.3V_NORMAL) IC8902 (+1.26V_MEMC) IC9102 DC to DC Q8003 PANEL_VCC Q8800 AMP_MUTE
Pin Regulator Pin Regulator Pin Regulator Pin Regulator Pin HVDD T-CON Pin Control 2nd Driver Pin Pin 25 IC8801
[1] 0V (Gnd) [1] 5V [1] 0V (Gnd) [1] 0V (Gnd) [1] 0V (Gnd) B 0.679V B 0V
[2] 1.26V (Out) [2] 3.34V (In) [2] 11.8V (In) [2] 11.8V (In) [2] 11.72V (In) C 0V C 3.336V
[3] 3.3V (In) [3] 1.8V (Out) [3] 0V (Gnd) [3] 0V (Gnd) [3] 11.72V (In) E Gnd E Gnd
[4] Gnd [4] 0.8V [4] 0.8V [4] 3.25V
IC1000 SOC Reset [5] Gnd [5] 0.86V [5] 0.7V [5] 3.2V Q8004 PANEL_VCC D9101 VGH/VDD
Pin Generator [6] 0.9V [6] 3.36V (PWR On/Off2 C [6] 3.36V (PWR On/Off2 [6] 0V Pin Switch Pin Rectifyer
[1] 3.32V (In) [7] 0.9V [7] 3.36V (Out) [7] 1.3V (Out) [7] 0V S 11.8V (In) A 15.4V
[2] 0V (Gnd) [8] 1V [8] 3.36V (Out) [8] 1.3V (Out) [8] 11.7V G 1.8V (Enable) AC 22.2V
[3] 3.3V (Out) [9] 2.38V [9] 0V (Gnd) D 11.8V (Out) C 27.4V (VGH)
[10] 3.36V (PWR On/Off1 Ctl) IC8007 Power Det Gen IC8903 (+3.3V_MEMC) [10] 1.13V
IC8000 5V Regulator Pin (+12V and +3.5V) Pin Regulator [11] 0V (Gnd) Q8005 INV_ON D9102 VGL/VCC
Pin for USB IC8003 (+5V_NORMAL) [1] 0V (Gnd) [1] 0V (Gnd) [12] 0V (Gnd) Pin Driver Pin Rectifyer
[1] 11.79V (In) Pin Regulator [2] 3.6V (In) [2] 11.8V (In) [13] 0V (Gnd) B 0V (INV ON) En A (-5V VGL)
[2] 5V (Out) [1] 0V (Gnd) [3] 3.5V (Out) [3] 0V (Gnd) [14] 7.7V C 3.1V (Out) AC (-1.9V)
[3] 5V (Out) [2] 11.8V (In) [4] 0.8V [15] 7.7V (HVDD) E Gnd C 0V
[4] 10.5V [3] 0V (Gnd) IC8008 Power Det Gen [5] 0.8V [16] 0V (Gnd)
[5] 3.3V [4] 0.8V Pin (+24V) [6] 3.36V (PWR On/Off2 Ctl) Q8200 IR Buffer
[6] 0.8V [5] 0.86V [1] 0V (Gnd) [7] 3.3V (Out) IC9300 Reset for Pin 2nd
[7] 4.99V [6] 3.37V (PWR On/Off2 Ctl) [2] 3.6V (In) [8] 3.3V (Out) Pin LG5111 B
[8] 0V (Gnd) [7] 5V (In) [3] 3.7V (Out) [1] 3.32V (In) C
[8] 5V (In) IC9100 P-GAMMA [2] 0V (Gnd) E Gnd
IC8001 D1.2V and A1.2V IC8800 (+1.8V_AMP) Pin Chip [3] 3.34V (Out)
Pin Regulator IC8004 A2.5V Regulator Pin Regulator [1] 3.3V Q8201 IR Buffer
[1] 0V (Gnd) Pin for USB [1] 0V (Gnd) [2] 0V (Gnd) IC9302 (1.8V_L/Dimming) Pin 1st
[2] 3.3V [1] n/c [2] 1.8V (Out) [3] 3.3V (In) Pin Regulator B 0V
[3] 0V (Gnd) [2] 3.26V (In) [3] 3.295V (In) [4] 0V (Gnd) [1] 0V (Gnd) C 3.3V
[4] 1.2V [3] 3.26V (In) [5] 6.8V [2] 11.8V (In) E Gnd
[5] 3.3V [4] n/c IC8901 (+1.5V_MEMC) [6] 6.8V [3] 0V (Gnd)
[6] n/c [5] n/c Pin Regulator [7] 15.3V [4] 0.8V Q8306 HDMI
[7] 4.46V [6] 2.55V (Out) [1] 0V (Gnd) [8] 15.3V [5] 0.76V Pin Det
[8] 3.3V [7] 0.8V [2] 1.5V (Out) [9] n/c [6] 3.34V (PWR On/Off2 Ctl) B 0V
[9] 3.3V [8] 0V (Gnd) [3] 3.3V (In) [10] 13.47V [7] 1.8V (In) C 3.3V
[10] 3.3V [11] 12.75V [8] 1.8V (In) E Gnd
[11] 1.2V [12] 11.8V
[12] Gnd [13] 10V Q8001 PANEL_VCC Q8307 HDMI
[13] 3.3V [14] 5.96V Pin Control 1st Driver Pin Det
[14] 0.8V [15] 4.06V B 0V B 0V
[16] 15.3V C 0.68V C 4.18V
[17] 0V E Gnd E Gnd
[18] 2.96V
[19] 2.33V
[20] 3.3V (In)
IC602 D1.8V IC8200 RS232 IC8400 RGB IC8401 EDID Data IC9303 EEPROM Q901 FLASH_WP Q8308 CEC Remote
Pin Regulator Pin Routing Pin H/V Sync Pin PC Pin for LG5111 Pin for IC901 Pin HDMI CEC
[1] 0V (Gnd) [1] 0V [1] 1.9V [1] 0V (Gnd) [1] 0V (Gnd) B 0V (Flash_WP) [B] 2.72V
[2] 3.29V (PWR On/Off1 Ctl) [2] 0V [2] 1.9V [2] 0V (Gnd) [2] 0V (Gnd) C 3.36V [G] 2.73V
[3] 0.9V (DDR_VTT) [3] 0V [3] 4.4V [3] 0V (Gnd) [3] 0V (Gnd) E Gnd [S] 3.27V
[4] 0.93V [4] 0V [4] 0V [4] 0V (Gnd) [4] 0V (Gnd) [D] 3.37V
[5] 1.83V [5] 0V [5] 0.9V [5] 0.7V [5] 3.37V Q8000 RL_ON (PWR_On) D8312 3.5V Pull Up
[6] 3.38V (In) [6] (-5.47V) [6] n/c (4.5V) [6] 4.1V [6] 3.37V Pin 1st Driver Pin HDMI CEC
[7] 1.8V (Out) [7] n/c (5.59V) [7] 0V (Gnd) [7] 4.5V [7] 3.34V B 0.66V A1 0V
[8] 0.91V (DDR_VTT) [8] n/c (0V) [8] n/c (4.5V) [8] 4.5V (In) [8] 3.37V (In) C 0V C 3.26V
[9] n/c (3.3V) [9] n/c (1.9V) E Gnd A2 3.2V
IC8100 EEPROM [10] n/c (0.2V) [10] n/c (1.9V) IC9000 Serial Flash Q200 (1.8V_HDMI)
Pin Micro [11] n/c (3.3V) [11] n/c (4.5V) Pin T-CON Pin Switch Q8002 PWR_ON D8306, 7, 9 5V Pull Up Routing
[1] 0V (Gnd) [12] 3.35V [12] 0.9V [1] 0.06V S 1.83V (Out) Pin Switch Pin HDMI SCL/SDA
[2] 0V (Gnd) [13] 0V [13] 0.9V [2] 0.67V G 3.35V (PWR On/Off2 Ctl) [1] 3.36V (In) A1 5.04V
[3] 0V (Gnd) [14] (-5.47V) [14] 5V [3] 3.3V (In) D 1.83V (In) [2] 0V C 4.58V
[4] 0V (Gnd) [15] 0V (Gnd) [4] 0V (Gnd) [3] 3.3V (Out) A2 0V
[5] 3.37V [16] 3.37V [5] 0V Q701 Tuner SIF
[6] 3.37V [6] 0.34V Pin (Sound) Buffer Q8300, 2 HDMI 2
[7] 0V (Gnd) [7] 3.31V (In) B 0.16V Pin Det
[8] 3.37V [8] 3.34V (In) C Gnd B 4.2V
E 0.83V C 0V
E Gnd
Q702 Tuner Video
Pin (Analog) Buffer Q8303, 4, 5 HDMI 3
B 2.05V Pin Det
C 2.75V B 0V
E Gnd C 4.2V
E Gnd
47LE8500
Conclusion Direct View LCD
Page