Beruflich Dokumente
Kultur Dokumente
Solution:
Since volume is constant, use Charles’ Law on constant volume processes.
P1/T1=P2/T2
Note: P and T should be absolute.
P2=48.99 psia
P2g=48.99-14.7
P2g=34.29 psig
2. Four hundred cubic centimeters of gas at a pressure of 740 mmHg absolute and temperature of 18
degree C undergoes a process until the pressure and temperature becomes 760 mmHg absolute and 0
degrees C respectively. Calculate the final volume of the gas. (Electrical Engineering
Board Exam Problem)
Since all the parameters (temperature, pressure and volume) changes, use combined gas law
PV/T=constant
P1V1/T1=P2V2/T2
(740)(400)/(18+273)=(760)V2/(0+273)
V2=365.3 cc
3. A single acting air compressor with a clearance of 6% took air at atmospheric pressure and
temperature of 85 degrees F, discharges it at a pressure of 85 psia. Assuming that the compression is
isentropic, find the piston displacement per cycle and the air power (hp) of the compressor if the RPM is
750. (Mechanical Engineering Board Exam 1978)
(I haven't got this correct yet, LOL)
4. Steam enters turbine stage with an enthalpy of 3628 kJ/kg at 70m/s and leaves the same stage with an
enthalpy of 2846 kJ/kg and velocity of 124 m/s. calculate the work done by the steam. (Mechanical
Engineering Board Exam 1986)
Solution:
Just like the 90% of all thermo problems, this one can be solved using the first law of thermodynamics.
Ein=Eout
H1+KE1=H2+KE2+W
W=(H1-H2)+(KE1-KE2)
W=(3628-2846)+(70^2/1000-124^2/1000)
W=776.5 76J/kg
5. In an air standard Otto cycle, the clearance volume is 18% of the displacement volume. Find the
thermal efficiency? (Mechanical Engineering Board Exam 1993)
Solution:
e = 1-1/rk^(k-1)
e = 1-1/(6.6556)^(1.4-1)=.53
e=53%
6.A reversed Carnot cycle is used for cooling. The input work is 12kW, while the COP is 3.8. Calculate the
refrigerating effect in TOR. (Mechanical Engineering Board Exam)
Solution:
RE=3.8(12kW)(1Tor/3.516kW)=12.97TOR
7. The compression ratio of a standard gasoline engine is 8. The heat added is 1850kJ/kg. If the initial
pressure and temperature are 100Kpa and 25 degrees C respectively, determine the temperature at the
end of isentropic expansion. (Mechanical Engineering Board Exam)
Solution:
Rk=8
Qa=1850kJ/kg
P1=100kPa
T1=25+273=298K
rk=V1/V2=8
T2/T1=(V1/V2)^(k-1); k of air is 1.4
T2=((8)^(1.4-1))(298)
T2=684.62K
1850=(.7186)(T3-684.62)
T3=3259.07K
V4/V3=rk
(V4/v3)^(k-1)=(T3/T4)
T4 = 3259.07/((8)^(1-1.4))
T4 = 1418.6K
t = 1145.6 deg C
8. What is the logarithmic mean temperature difference (LMTD) of a double pipe counterflow heat
exchanger if the fluid enters at 90 degrees C and exits at 50 degrees C. Inside the inner pipe, another
fluid enters at 20 degrees C and exits at 60 degrees C. (Mechanical Engineering Board Exam)
Solution:
Since you will get zero when you use the conventional LMTD version, use the arithmetic mean
temperature difference (AMTD) instead.
AMTD=((90-60)+(50-20))/2=30
9. The volume of concrete needed for the foundation of an engine is 12 cubic meters. The concrete
mixture is 1:3:5 by volume. Calculate the number of 40 kg bags of cement needed considering the density
of cement to be 1500kg/cu.m. (Mechanical Engineering Board Exam)
Solution:
m = density(Volume)
Sacks=(2000kg)(1sack/40kg)
Sacks=50 sacks
10. A 305mm x 457mm four stroke single acting diesel engine is rated at 150 kW at 260 rpm. Fuel
consumption at rated load of 0.26 kg/kw-hr with a heating value of 43912 KJ/kg. Calculate the brake
thermal efficiency. (Mechanical Engineering Board Exam 1990)
Fuel mass=(150kw)(0.26kg/kw-hr)
Fuel mass=39kg/hr
Eb=(150)/(475)=31.53%