Beruflich Dokumente
Kultur Dokumente
(1) When unpacking or any of the following parts has been replaced, be sure to make this
adjustment:
• Photoconductive drum • Developer material • Laser optical unit
• Transfer roller • Drum cleaning blade
• Main charger grid • SRAM board
(2) Be sure to perform this adjustment whenever HDD data are cleared.
<Procedure>
(1) While pressing [0] and [5] simultaneously, turn the power ON. Adjustment Mode
(2) Select the A4/LT drawer. Key in “10” and press the [FAX] button to print a “Patch chart for gamma
adjustment”.
(3) Place the patch chart for adjustment printed in step (2) face down on the original glass. Place the
chart aligning its black side of the gradation pattern against the original scale.
(4) Key in a code and press the [START] button.
(5) If the adjustment is finished properly, press [OK] to have its results reflected.
(To cancel the reflection of adjustment results, press the [CANCEL] button.)
In the case of an abnormal ending, “ADJUSTMENT ERROR” is shown.
Press the [CANCEL] button to clear the error display. When it is cleared, the control panel display
will return to the ready state. Then, check if the patch chart on the original glass is placed in the
wrong direction or if it is placed inclined on the original glass, and then repeat step (3) and
afterward.
7114 7116 7115 7258 7126 Manual density mode The larger the value is, the
center value darker the image becomes.
Acceptable values: 0 to 255
(Default: 128)
7117 7119 7118 7261 - Manual density mode The larger the value is, the
light step value lighter the light side becomes.
Acceptable values: 0 to 255
(Default: 20) 6
7120 7122 7121 7264 - Manual density mode The larger the value is, the
dark step value darker the dark side
becomes.
Acceptable values: 0 to 255
(Default: 20)
7123 7125 7124 7267 7129 Automatic density The larger the value is, the
mode darker the image becomes.
Acceptable values: 0 to 255
(Default: 128)
7114 7116 7115 7134 Manual density mode The larger the value is, the
center value darker the image becomes.
Acceptable values: 0 to
255 (Default: 128)
7123 7125 7124 7137 Automatic density The larger the value is, the
mode darker the image becomes.
Acceptable values: 0 to 255
(Default: 128)
Make a test copy and compare the image obtained with the current settings; if necessary, make
adjustment using the following procedure.
(1) While pressing [0] and [5] simultaneously, turn the power ON.
(4) Press the [OK] or [INTERRUPT] button to store the value. The equipment goes back to the
ready state.
(5) Press the [FAX] button and then the [START] button. Then perform test copying.
(6) If the desired image density has not been attained, repeat step (1) to (5).
7033 7043 7034 7279 (*1) 7050 (*1) Automatic density mode The larger the value is,
the lighter the
7041 7048 7042 7280 (*1) 7051 (*1) Manual density mode background becomes.
Acceptable values:0 to
255
(Default: 128)
Make a test copy and compare the image obtained with the current settings; if necessary, make
adjustment using the following procedure.
*1: e-STUDIO206L/256/306/356/456/506 only.
6
e-STUDIO207L/257/307/357/457/507 < Adjustment Mode (05) >
Original mode
<Procedure>
Procedure is same as that of P. 6-23 "6.4.2 Density adjustment".
7056 7058 7057 7249 7059 (*1) Sharpness adjustment The larger the value is, the
sharper the image
becomes; while the smaller
the value is, the softer the
image becomes. The
smaller the value is, the
less moire tends to appear.
Acceptable values: 0 to
255
(Default: 128)
Make a test copy and compare the image obtained with the current settings; if necessary, make
adjustment using the following procedure.
*1: e-STUDIO206L/256/306/356/456/506 only.
7283 7285 7284 7236 7289 Automatic density mode 0: Background peak / fixed
1: Background peak /
7286 7288 7287 7237 7290 Manual density mode varied
<Procedure>
Procedure is same as that of P. 6-23 "6.4.2 Density adjustment".
<Procedure>
Procedure is same as that of P. 6-23 "6.4.2 Density adjustment".
Color Item to be
Text/ User Remarks
Photo Text Docume adjusted
Photo custom
nt
7190-0 7192-0 7191-0 7276-0 7193-0 Low density The larger the value is, the
(*1) density of the item to be adjusted
becomes darker.
7190-1 7192-1 7191-1 7276-1 7193-1 Medium density Acceptable values: 0 to 255.
(*1) (Default: 128)
<Procedure>
(1) While pressing [0] and [5] simultaneously, turn the power ON.
(2) Key in the code for an item to be adjusted and then press the [START] button.
(3) Key in a number for the density area to be adjusted (0, 1 or 2), and then press the [START]
button.
0: Low density 1: Medium density 2: High density
(5) Press the [OK] or [INTERRUPT] button to store the value in memory. The equipment goes back
to the ready state.
(7) Press the [FAX] button and then the [START] button. Then perform test copying.
(8) If the desired image density has not been attained, repeat step (2) to (7).
7218-0 7219-0 7220-0 7221-0 Adjustment of When the value is decreased, text becomes
to 4 to 4 to 4 to 4(*1) image density lighter.
Acceptable values: 0 to 10
Notes:
1. Set not to reverse the large and small
number of the setting value
corresponding to the sub code.
Ex.) When the image density level for
7218-0, 7218-1, 7218-2, 7218-3, and
7218-4 is assumed to be “A”, “B”, “C”,
“D”, and “E” respectively, they should
have the following correlation:
A B C D E
2. Remember that the image
specifications and life span of the
replacing parts may not meet the
standard when the setting value is
changed from the default value.
*1: e-STUDIO206L/256/306/356/456/506 only.
<Procedure>
(1) While pressing [0] and [5] simultaneously, turn the power ON.
(3) Key in the sub code (0, 1, 2, 3 or 4), and press the [START] button.
(5) Press the [OK] or [INTERRUPT] button to store the value in memory. The equipment goes back
to the ready state.
(7) Press the [FAX] button and then select an original mode. Then press the [START] button to
perform test copying.
(8) If the desired image density has not been attained, repeat step (2) to (7).
<Procedure>
Procedure is same as that of P. 6-23 "6.4.2 Density adjustment".
<Procedure>
Procedure is same as that of P. 6-23 "6.4.2 Density adjustment".
<Procedure>
The procedure is the same as that of P. 6-23 "6.4.2 Density adjustment".
7325 7326 7327 When the value increases, the smudged text is improved. When the value
decreases, the faint text is improved.
Acceptable values: 0 to 9 (Default: 5)
<Procedure>
(1) While pressing [0] and [5] simultaneously, turn the power ON.
(4) Press the [OK] or [INTERRUPT] button to store the value. The equipment goes back to the ready
state.
(5) Turn the power OFF and then back ON to perform printing job.
(6) If the desired text density has not been attained, repeat step (2) to (5).