Beruflich Dokumente
Kultur Dokumente
MANUAL
028754- M
2/01/02 (Original Publication)
Updated 7/18/14
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Service:
Parts:
Date of Installation:
Model Number:
Serial Number:
Phase
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
131206
Models 750, 751, 754, 774, 791, 794 1 To the Installer
Water Connections Each unit requires one power supply for each data
(Water Cooled Units Only) label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity, and other electrical specifications. Refer to
An adequate cold water supply must be provided with the wiring diagram provided inside of the electrical box
a hand shut- off valve. On the underside rear of the for proper power connections.
base pan, two 3/8” I.P.S. (for single- head units) or two
1/2” I.P.S. (for double- head units) water connections
for inlet and outlet have been provided for easy
hook- up. 1/2” inside diameter water lines should be
CAUTION: THIS EQUIPMENT MUST BE
connected to the machine. (Flexible lines are
PROPERLY GROUNDED! FAILURE TO DO SO
recommended, if local codes permit.) Depending on
CAN RESULT IN SEVERE PERSONAL INJURY
local water conditions, it may be advisable to install a
FROM ELECTRICAL SHOCK!
water strainer to prevent foreign substances from
clogging the automatic water valve. There will be only
one water “in” and one water “out” connection for both
single- head and double- head units. DO NOT install a DO NOT operate this freezer with larger fuses
hand shut- off valve on the water “out” line! Water than specified on the unit data label. Failure to follow
should always flow in this order: first, through the this instruction may result in electrocution or damage
automatic water valve; second, through the to the machine.
condenser; and third, through the outlet fitting to an
open trap drain.
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
A back flow prevention device is required of the frame by the authorized installer. The installation
on the incoming water connection side. Please location is marked by the equipotential bonding
refer to the applicable National, State, and local codes symbol (5021 of IEC 60417-1) on both the removable
for determining the proper configuration. panel and the equipment’s frame.
Electrical Connections
Stationary appliances which are not equipped
with a power cord and a plug or another device to
In the United States, this equipment is intended to be
disconnect the appliance from the power source must
installed in accordance with the National Electrical
have an all-pole disconnecting device with a contact
Code (NEC), ANSI/NFPA 70-1987. The purpose of the
gap of at least 3 mm installed in the external
NEC code is the practical safeguarding of persons and installation.
property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. In all other areas of the world,
equipment should be installed in accordance with the Appliances that are permanently connected to
existing local codes. Please contact your local fixed wiring and for which leakage currents may
authorities. exceed 10 mA, particularly when disconnected or not
used for long periods, or during initial installation, shall
have protective devices such as a GFI, to protect
FOLLOW YOUR LOCAL ELECTRICAL CODES! against the leakage of current, installed by the
authorized personnel to the local codes.
101027
To the Installer 2 Models 750, 751, 754, 774, 791, 794
Refrigerant
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent synthetic In consideration of our environment, Taylor
elastomer-sheathed cord (Code designation 60245 uses only earth friendly HFC refrigerants. The HFC
IEC 57) installed with the proper cord anchorage to refrigerant used in this unit is R404A. This refrigerant
relieve conductors from strain, including twisting, at is generally considered non-toxic and non-flammable,
the terminals and protect the insulation of the with an Ozone Depleting Potential (ODP) of zero (0).
conductors from abrasion.
However, any gas under pressure is potentially
If the supply cord is damaged, it must be replaced by hazardous and must be handled with caution. NEVER
an authorized Taylor service technician in order to fill any refrigerant cylinder completely with liquid.
avoid a hazard. Filling the cylinder to approximately 80% will allow for
normal expansion.
Beater rotation must be clockwise as viewed Refrigerant liquid sprayed onto the skin may
looking into the freezing cylinder. cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
Note: The following procedures should be immediately with cold water. If burns are severe, apply
performed by a trained service technician. ice packs and contact a physician immediately.
Taylor reminds technicians to be cautious of
To correct the rotation on a three- phase unit, government laws regarding refrigerant recovery,
interchange any two incoming power supply lines at recycling, and reclaiming systems. If you have any
freezer main terminal block only. questions regarding these laws, please contact the
factory Service Department.
To correct rotation on a single- phase unit, change the
leads inside the beater motor. (Follow the diagram
printed on the motor.) WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely moisture
Electrical connections are made directly to the absorbent. When opening a refrigeration system, the
terminal block provided in the main control box located maximum time the system is open must not exceed 15
under the upper left side panel on the countertop unit, minutes. Cap all open tubing to prevent humid air or
or behind the service panel on the console units. water from being absorbed by the oil.
130819
Models 750, 751, 754, 774, 791, 794 3 To the Installer
Section 2 To the Operator
The freezer you have purchased has been carefully compliant with the EU Directive as well as other similar
engineered and manufactured to give you dependable legislation in effect after August 13, 2005. Therefore,
operation. The Taylor soft- serve models covered in it must be collected separately after its use is
this manual consist of the following: 750, 751, 754, completed, and cannot be disposed as unsorted
774, 791, and 794. municipal waste. The user is responsible for returning
the product to the appropriate collection facility, as
These units, when properly operated and cared for, will specified by your local code.
produce a consistent quality product. Like all
mechanical products, they will require cleaning and For additional information regarding applicable local
maintenance. A minimum amount of care and laws, please contact the municipal facility and/or local
attention is necessary if the operating procedures distributor.
outlined in this manual are followed closely.
131206
To the Operator 4 Models 750, 751, 754, 774, 791, 794
Section 3 Safety
DO NOT use a water jet to clean or rinse the Failure to follow these instructions may result in
freezer. Failure to follow these instructions may result electrocution. Contact your local authorized Taylor
in serious electrical shock. Distributor for service.
130819
Models 750, 751, 754, 774, 791, 794 5 Safety
Cleaning and sanitizing schedules are
S DO NOT allow untrained personnel to operate governed by your state or local regulatory agencies
this machine. and must be followed accordingly. Please refer to the
cleaning section of this manual for the proper
S DO NOT put objects or fingers in door spout.
procedure to clean this unit.
S DO NOT operate the freezer unless all service
panels and access doors are restrained with
screws.
S DO NOT remove any internal operating parts Access to the service area of the unit must be
(example: freezer door, beater, scraper restricted to persons having knowledge and practical
blades, etc.) unless all control switches are in experience with the unit, in particular as far as safety
the OFF position. and hygiene are concerned.
Failure to follow these instructions may result in
contaminated product or severe personal injury to DO NOT run the unit without product. Failure to follow
fingers or hands from hazardous moving parts. this instruction can result in damage to the unit.
130819
Safety 6 Models 750, 751, 754, 774, 791, 794
Section 4 Operator Parts Identification
Model 750
101217
Models 750, 751, 754, 774, 791, 794 7 Operator Parts Identification
Model 751
111101
Operator Parts Identification 8 Models 750, 751, 754, 774, 791, 794
Model 754
Models 750, 751, 754, 774, 791, 794 9 Operator Parts Identification
Model 774
140616
Operator Parts Identification 10 Models 750, 751, 754, 774, 791, 794
Model 774 Topping Pump (053794- )
ITEM DESCRIPTION PART NO.
1 Knob-Plunger-Tan 032762-TAN
1 Knob-Plunger-Brown 032762-BRN
1 Knob-Plunger-Red 032762-RED
2 O-Ring-9/16 OD x .103 W 016369
3 Nut-Plunger 036577
4 Collar-Gaging 1/2 Ounce 035514
5 Tube-Plunger 032757
6 Insert-Plunger 032758
7 Spring-Plunger 032761
8 Washer-Nylon 032760
9 Plunger 036578
10 Seal Assembly X33057
10a O-Ring-13/16 OD x .103 W 019330
11 Body-Syrup Pump 047934
12 Nut-Spout 036821
13 Lid-Pump 036822
14 Tube-Discharge 050912
15 O-Ring-1-5/16 OD x .103 W 048149
16 O-Ring-1 OD x .103 W 048148
17 Kit-Valve-Captured Ball Shallow 048166-001
Includes:
1 - Body A.-Pump Valve
1 - O-Ring-1-5/16 OD x .103W (048149)
1 - Brush-cleaning (054068)
1 - Instruction Sheet-Installation/Cleaning
Models 750, 751, 754, 774, 791, 794 11 Operator Parts Identification
Model 791
120613
Operator Parts Identification 12 Models 750, 751, 754, 774, 791, 794
Model 794
130508
Models 750, 751, 754, 774, 791, 794 13 Operator Parts Identification
Models 750 & 751 Single Spout Door and Beater Assembly
Operator Parts Identification 14 Models 750, 751, 754, 774, 791, 794
Models 754, 774 & 794 Three Spout Door and Beater Assembly
Models 750, 751, 754, 774, 791, 794 15 Operator Parts Identification
Model 791 Three Spout Door and Beater Assembly
120124
Operator Parts Identification 16 Models 750, 751, 754, 774, 791, 794
Accessories
140718
Models 750, 751, 754, 774, 791, 794 17 Operator Parts Identification
Section 5 Important: To the Operator
750/751
754/774/791/794
Important: To the Operator 18 Models 750, 751, 754, 774, 791, 794
The following chart identifies the symbol definitions. During long “No Sale” periods, it is necessary to warm
the product in the freezing cylinder to approximately
35_F to 40_F (1.7_C to 4.4_C) to prevent overbeating
= OFF and product breakdown.
MIX LOW Indicator Light To resume normal operation, press the AUTO key.
When the unit cycles off, the product in the freezing
Located on the front of the machine is a mix level cylinder will be at serving viscosity. At this time, place
indicating light. When the light is flashing, it indicates the air tube (end with the hole) into the mix inlet hole
that the mix hopper has a low supply of mix and should and install the air orifice.
be refilled as soon as possible. Always maintain at
least 3” (7.6 cm) of mix in the hopper. If you neglect to
add mix, a freeze- up may occur. This will cause
eventual damage to the beater, blades, drive shaft, WASH Key
and freezer door.
When the WASH key is pressed, the light comes on.
MIX REF Key This indicates beater motor operation. The STANDBY
or AUTO modes must be cancelled first to activate the
When the MIX REF key is pressed, the light comes on WASH mode.
indicating the mix hopper refrigeration system is
operating. For the Models 754, 774, 791, and 794 the
MIX REF is controlled by the left side of the freezer as
viewed from the operator end. The MIX REF function AUTO Key
cannot be cancelled unless the AUTO or STANDBY
modes are cancelled first.
When the AUTO key is pressed, the light comes on.
This indicates that the main refrigeration system has
STANDBY Key been activated. In the AUTO mode, the WASH or
STANDBY functions are automatically cancelled. The
The Separate Hopper Refrigeration System (SHR) MIX REF function is automatically locked in to
and the Cylinder Temperature Retention System maintain the mix in the mix hopper.
(CTR) are standard features on these machines. The
SHR incorporates the use of a separate small Note: An indicating light and an audible tone will
refrigeration system to maintain the mix in the hopper sound whenever a mode of operation has been
below 40_(4.4_C) to assure bacteria control. The CTR pressed. To cancel any function, press the key again.
works with the SHR to maintain a good quality product. The light and mode of operation will shut off.
130819
Models 750, 751, 754, 774, 791, 794 19 Important: To the Operator
Reset Button draw handle is raised, new mix and air from the
hopper will flow down into the freezing cylinder.
This will keep the freezing cylinder properly
On counter models, the reset button is located on the loaded and will maintain overrun.
side of the unit. On console models, the reset button
is located in the service panel. The reset protects the 2. During long “No Sale” periods, remove the air
beater motor from an overload condition. If an overload orifice. Lubricate the o- rings on the air tube
occurs, the reset mechanism will trip. To properly reset (the end without the hole), and place it into
the freezer, press the AUTO key to cancel the cycle. the mix inlet hole. This will prevent any mix
Turn the power switch to the OFF position. Press the from entering the freezing cylinder.
reset button firmly. IMPORTANT: Make sure the level of mix in the
hopper is below the mix delivery hole in the
feed tube. Failure to follow this instruction may
Do not use metal objects to press the reset result in lower product quality when normal
button. Failure to follow this instruction may operation is resumed.
result in electrocution. The air orifice is used to meter a certain amount
Turn the power switch to the ON position. Press the of air into the freezing cylinder. The air orifice
WASH key and observe the freezer’s performance. maintains overrun and allows enough mix to enter
Open the side access panel. Make sure the beater the freezing cylinder after a draw.
motor is turning the drive shaft in a clockwise direction
(from the operator end) without binding.
Adjustable Draw Handle
If the beater motor is turning properly, press the WASH
key to cancel the cycle. Press the AUTO key to resume These units feature an adjustable draw handle to
normal operation. If the freezer shuts down again, provide the best portion control. The draw handle
contact a service technician. (For Models 754, 774, should be adjusted to provide a flow rate of 5 to 7- 1/2
791, and 794 press the AUTO key on both sides of the oz. (148 to 222 ml) of product per 10 seconds. To
unit to resume normal operation.) INCREASE the flow rate, turn the screw
COUNTERCLOCKWISE. Turn the screw
CLOCKWISE to DECREASE the flow rate. During
“Sanitizing” and “Rinsing”, the flow rate can be
Air Tube increased by removing the pivot pin and placing the
restrictive bar on the TOP. When drawing product,
The air tube serves two purposes. One end of the tube always place the restrictive bar on the bottom.
has a hole and the other end does not.
IMPORTANT! When dispensing product, pull only
one draw handle at a time.
Figure 1
Figure 2
1. After priming the machine, lubricate the o- rings
on the air tube (the end with the hole) and Note: Once the draw rate is set, tighten the lock nut
place it into the mix inlet hole. Every time the with a wrench.
130819
Important: To the Operator 20 Models 750, 751, 754, 774, 791, 794
Section 6 Operating Procedures
The Model 751 has been selected to illustrate the Step 3
step- by- step operating procedures for all models Prepare a pail of an approved 100 PPM sanitizing solu-
contained in this manual. These models, for all tion (examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or
practical purposes of operation, are the same. 2 gal. [7.6 liters] of Stera- SheenR). USE WARM WA-
TER AND FOLLOW THE MANUFACTURER’S SPE-
Each unit stores mix in a hopper. The mix then flows CIFICATIONS. Sanitize the topping pumps by placing
by gravity through an air tube down into the freezing the entire pump assembly in the pail of sanitizing solu-
cylinder. They all have 3.4 quart (3.2 liter) capacity tion. Pump the solution through the assembly to thor-
freezing cylinders. The Models 750, 751, 754, and 774 oughly sanitize the pump.
have 20 quart (18.9 liter) mix hoppers. The Models 791
Step 4
and 794 have 14 quart (13.2 liter) mix hoppers. Remove the two topping pumps. Fill each stainless
syrup jar with topping. Replace the topping pumps in
Duplicate the following procedures, where they apply,
the syrup jars.
for the second freezing cylinder on Models 754, 774,
791, and 794.
Step 1
Remove the two stainless syrup jars with topping
pumps from the syrup rail. Check the water level in the
heated syrup topping well. Make sure the water is filled
to the indicating mark on the bottom of the well. The
heated rail should have 32 oz. (946.2 ml) of water.
Step 2
Place the heater switch in the ON position.
080602
Models 750, 751, 754, 774, 791, 794 21 Operating Procedures
Insert the drive shaft into the freezing cylinder, hex end
first, and into the rear shell bearing until the seal fits
securely over the rear shell bearing. Engage the hex
end firmly into the drive coupling. Be sure the drive
shaft fits into the drive coupling without binding.
Figure 6
Figure 5
Figure 10
Step 4
Figure 8
Insert the baffle rod(s) through the opening in the
beater(s) and seat the door flush with the freezing
Slide the two o- rings into the grooves on the prime
cylinder. With the door seated on the freezer studs,
plug(s). Apply an even coat of Taylor Lube to the
install the handscrews. Tighten equally in a crisscross
o- rings and shaft(s).
pattern to insure the door is snug.
Figure 11
Figure 9
Note: On the Models 754, 774, 791, and 794, the
Note: There are two prime plugs for the Models 754, short handscrews go on the bottom and the long
774, 791, and 794 door, one for each freezing cylinder. handscrews go on the top.
Figure 14
Slide the fork over the bar in the slot of the draw valve.
Figure 12 Secure with pivot pin.
Note: Models 754, 774, 791, and 794 have three draw
valves.
Figure 15
Note: Models 754, 774, 791, and 794 have three draw
handles. Slide the fork of the draw handle in the slot of
the draw valve, starting from the right. Slide the pivot
pin through each draw handle as you insert them into
the draw valves.
Note: These units feature adjustable draw handles to
provide the best portion control. The draw handles can
be adjusted for different flow rates. See page 20 for
Figure 13 more information on adjusting these handles.
101109
Operating Procedures 24 Models 750, 751, 754, 774, 791, 794
Step 7 Models 791 & 794: Slide the rear drip pan into the hole
Snap the design cap(s) over the end of the door in the front panel.
spout(s).
Step 10
Slide two o- rings on one end of the air tube. Slide two
o- rings on the other end of the air tube.
Figure 16
Step 8
Install the front drip tray and the splash shield under
the door spout(s).
Figure 19
Slide the small o- ring into the groove of the air orifice.
Do not lubricate the o- ring.
Figure 17
Step 9
Slide the rear drip pan(s) into the hole in the side panel.
Figure 20
Note: Make sure the hole in the air orifice is clean and
is not clogged. If the hole in the air orifice should
become clogged, use soap and hot water to clear the
Figure 18 hole. Do not enlarge the hole in the air orifice.
Figure 22
Step 3
Figure 21 While the solution is flowing into the freezing cylinder,
brush clean the mix hopper. When cleaning the
Step 11 hopper, take particular care in brushing the mix level
Lay the air tube (with the air orifice installed) and the sensing probe on the rear wall of the hopper, the mix
hopper gasket in the bottom of the mix hopper for inlet hole, the air tube, and the hopper gasket.
sanitizing.
Figure 23
Sanitizing
Step 1
Prepare an approved 100 PPM sanitizing solution
(examples: 2- 1/2 gal. [9.5 liters] of Kay- 5R or 2
gal. [7.6 liters] of Stera- SheenR). USE WARM WA-
TER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.
Step 2
Pour the sanitizing solution into the hopper and allow
it to flow into the freezing cylinder. Figure 24
130118
Operating Procedures 26 Models 750, 751, 754, 774, 791, 794
Step 6
Place an empty pail beneath the door spout and raise
the prime plug.
Figure 25
Step 4
Place the power switch in the ON position.
Figure 28
Step 7
When a steady stream of sanitizing solution is flowing
from the prime plug opening in the bottom of the
freezer door, lower the draw handle. Draw off all the
sanitizing solution.
Figure 26
Step 5
Press the WASH key. This will cause the sanitizing
solution in the freezing cylinder to agitate. Allow it to
agitate for five minutes.
Figure 29
Step 8
Once the sanitizer stops flowing from the door spout,
raise the draw handle and press the WASH key,
cancelling the beater motor operation.
Figure 32
Figure 30
Step 3
Repeat steps 1 through 9 for the other side of the Lubricate the o- rings on the air tube on the end with
freezer on Models 754, 774, 791, and 794. the small hole on the side.
Step 4
Install the air tube (the end with the hole) with the air
orifice installed into the mix inlet hole in the mix hopper.
Priming Step 5
Press the AUTO key. The AUTO light will come on
Step 1 indicating the main refrigeration system is operating.
With a pail beneath the door spout, lower the draw When the unit cycles off, the product will be at serving
handle. Be sure the prime plug is still in the UP viscosity.
position. Pour two gallons (7.6 liters) of fresh mix into Note: On Models 751, 754, 774, 791, and 794 the
the mix hopper and allow it to flow into the freezing MIX REF light will come on, indicating the mix
cylinder. This will force out any remaining sanitizing refrigeration system is operating to maintain the mix in
solution. When full strength mix is flowing from the the mix hopper.
door spout, raise the draw handle.
Figure 33
Step 6
Fill the hopper with mix. As the mix level comes in
contact with the mix level sensing probe on the rear
Figure 31 wall of the hopper, the MIX LOW light will shut off.
Step 5
ALWAYS FOLLOW LOCAL HEALTH CODES. Place an empty pail beneath the door spout and raise
the prime plug.
140718
Models 750, 751, 754, 774, 791, 794 29 Operating Procedures
Step 6 S adjustable draw handle(s)
When a steady stream of cleaning solution is flowing S design cap(s)
from the prime plug opening in the bottom of the S draw valve(s)
freezer door, lower the draw handle. Draw off all of the
solution. S prime plug(s)
S all o- rings
Step 7 Note: To remove o- rings, use a single service towel
Once the cleaner stops flowing from the door spout, to grasp the o- ring. Apply pressure in an upward
raise the draw handle and press the WASH key
direction until the o- ring pops out of its groove. With
cancelling the WASH mode.
the other hand, push the top of the o- ring forward and
Repeat steps 1 through 7 for the other side of the it will roll out of the groove and can be easily removed.
freezer on Models 754, 774, 791, and 794. If there is more than one o- ring to be removed, always
remove the rear o- ring first. This will allow the o- ring
to slide over the forward rings without falling into the
open grooves.
Disassembly
Step 4
Remove the o- rings from the air tube(s) and air
orifice(s).
MAKE SURE POWER SWITCH IS IN THE
“OFF” POSITION! Failure to follow this instruction Step 5
may result in severe personal injury from hazardous Return to the freezer with a small amount of cleaning
solution. Brush clean the rear shell bearing(s) at the
moving parts.
back of the freezing cylinder(s) with the black bristle
Step 1 brush.
Remove the handscrews, freezer door(s), beater(s),
scraper blades, and drive shaft(s) from the freezing
cylinder(s). Take these parts to the sink for cleaning.
Step 2
Remove the front drip tray and the splash shield.
Brush Cleaning
Step 1
Prepare a sink with an approved cleaning solution (ex-
amples: Kay- 5r or Stera- Sheenr). USE WARM WA-
TER AND FOLLOW THE MANUFACTURER’S SPE- Figure 34
CIFICATIONS. If another approved cleaner is used,
dilute it according to the label instructions. (IMPORT- Step 6
ANT: Follow the label directions. Too STRONG of a Remove the rear drip pan(s) and take to the sink for
solution can cause parts damage, while too MILD of a cleaning.
solution will not provide adequate cleaning.) Make Note: If the drip pan is filled with an excessive amount
sure all brushes provided with the freezer are available of mix, refer to the Troubleshooting Guide.
for brush cleaning.
Step 7
Step 2 Thoroughly brush clean all disassembled parts in the
Remove the seal(s) from the drive shaft(s). cleaning solution making sure all lubricant and mix film
is removed. Take particular care to brush clean the
Step 3
draw valve core(s) in the freezer door. Place all the
From the freezer door(s) remove:
cleaned parts on a clean, dry surface to air dry
S gasket(s) overnight.
S front bearing(s) Step 8
S pivot pin(s) Wipe clean all exterior surfaces of the freezer.
080324
Operating Procedures 30 Models 750, 751, 754, 774, 791, 794
Section 7 Important: Operator Checklist
061122
Models 750, 751, 754, 774, 791, 794 31 Important: Operator Checklist
j 6. If your machine is air cooled, check the Winter Storage
condensers for accumulation of dirt and lint.
Dirty condensers will reduce the efficiency and
If the place of business is to be closed during the winter
capacity of the machine. Condensers should be
months, it is important to protect the freezer by
cleaned monthly with a soft brush. Never use
following certain precautions, particularly if the
screwdrivers or other metal probes to clean
building is subject to freezing conditions.
between the fins.
Note: For machines equipped with an air filter, Disconnect the freezer from the main power source to
it will be necessary to vacuum clean the filters prevent possible electrical damage.
on a monthly schedule.
On water cooled freezers, disconnect the water
supply. Relieve pressure on the spring in the water
Caution: Always disconnect valve. Use air pressure on the outlet side to blow out
electrical power prior to cleaning the any water remaining in the condenser. This is
condenser. Failure to follow this instruction extremely important. Failure to follow this procedure
may result in electrocution. may cause severe and costly damage to the
refrigeration system.
j 7. If your machine is equipped with an auxiliary
refrigeration system, check the auxiliary Your local Taylor Distributor can perform this winter
condenser for accumulation of dirt and lint. Dirty storage service for you.
condensers will reduce the refrigeration
capacity of the mix hopper. Condensers must Wrap detachable parts of the freezer such as beater,
be cleaned monthly with a soft brush. Never use blades, drive shaft, and freezer door, and place them
screwdrivers or other metal probes to clean in a protected dry place. Rubber trim parts and gaskets
between the fins. Failure to follow this can be protected by wrapping them with
instruction may result in electrocution. moisture- proof paper. All parts should be thoroughly
cleaned of dried mix or lubrication which attract mice
and other vermin.
080324
Important: Operator Checklist 32 Models 750, 751, 754, 774, 791, 794
Section 8 Troubleshooting Guide
Scraper Blade X
Front Bearing X
Parts Replacement Schedule 36 Models 750, 751, 754, 774, 791, 794
Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
131206
Models 750, 751, 754, 774, 791, 794 37 Limited Warranty on Equipment
3. Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4. External hoses, electrical power supplies, and machine grounding.
5. Parts not supplied or designated by Taylor, or damages resulting from their use.
6. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9. Any Product purchased over the Internet.
10. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12. Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
Limited Warranty on Equipment 38 Models 750, 751, 754, 774, 791, 794
Section 11 Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
1, 2Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131206
Models 750, 751, 754, 774, 791, 794 39 Limited Warranty on Parts
LIMITED WARRANTY EXCEPTIONS
8. Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9. Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10. Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11. Any Part purchased over the Internet.
12. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13. Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14. Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
Limited Warranty on Parts 40 Models 750, 751, 754, 774, 791, 794
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.
Models 750, 751, 754, 774, 791, 794 41 Limited Warranty on Parts
Models 750, 751, 754, 774, 794
121031
(HP62 Refrigerant: 750 - J6110454, 751 - J6080596, 754 - J6080465, 774 - J6092382, and 794 - J4094101/up)
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
ADAPTOR A.-CASTER X18915 4 4 4 4 103
BEARING-FRONT 050216 1 1 2 2 2 000
+ Available Separately
BEARING-REAR SHELL 031324 1 1 2 2 2 000
+GUIDE-DRIP SEAL 028992 1 1 2 2 2 000
Section 12
42
BLOCK-TERMINAL-2 P 039422 1 1 2 2 2 103 SINGLE PHASE
BLOCK-TERMINAL-3 P 039423 1 1 2 2 2 103 THREE PHASE
SCREW-TERMINAL BLOCK 039420 2 2 4 4 4 000
BLOWER ASSEMBLY X47833-27 1 1 1 1 103
CAPACITOR-RUN 033047 1 1 1 1 103
BOOT-CAPACITOR 031314 1 1 1 1 000
HOUSING A.-w/WHEEL X30160 1 1 1 1 103
MOTOR-BLOWER 046536-27 1 1 1 1 103
BOARD-LOGIC X69570SER2 1 1 2 2 2 212 REPLACES X36641SER1
BOARD-POWER X69574-SER 1 1 2 2 2 212 REPLACES X32326-SER
FUSE-SLO BLO 051272 1 1 2 2 2 103
BRUSH-BLACK (1” X 2”) 013071 1 1 1 1 1 000
BRUSH-DOUBLE END 013072 1 1 1 1 1 000
BRUSH-WHITE (1” X 2”) 013073 1 1 1 1 1 000
BRUSH-WHITE (3” X 7”) 023316 1 1 1 1 1 000
CABLE-RIBBON 032445 1 1 2 2 103
CABLE-RIBBON 042599 2 103
+ Available Separately
COMPRESSOR - COPELAND 051958-58 1 512 J8108583/UP-220-240/380-415/50/3 136
LINE A.-ACCESS COMPRESSOR X42513 1 130 COPELAND 136
CAPACITOR-RUN 012906 1 103 230-60-1 - J8108583/UP 136
CAPACITOR-START 033044-1 1 103 230-60-1 - J8108583/UP 136
RELAY-START COMPRESSOR 051957-27 1 103 230-60-1 - J8108583/UP 136
43
CAPACITOR-RUN 012906 1 2 2 103 230-60-1
CAPACITOR-START 031790 1 2 2 103 230-60-1
RELAY-START 038145 1 2 2 103 230-60-1
COMPRESSOR - TECUMSEH 047519- 2 512
CAPACITOR-RUN 048132 2 103
CAPACITOR-START 036048 2 103
RELAY-START 036047 2 103
COMPRESSOR-AUXILIARY 047701-27 1 1 1 1 1 512
CAPACITOR-START 047703 1 1 1 1 1 103
RELAY-START 047702-27 1 1 1 1 1 103
COVER-TERMINAL 047739 1 1 1 1 1 103
CONDENSER-AUXILIARY 027155 1 1 1 1 1 103
CONDENSER-MAIN 046558 1 103
CONDENSER-MAIN 048233 1 2 2 2 103
COUPLING-DRIVE 012721 1 1 2 2 2 103
COVER A.-MIX HOPPER X38458-SER 1 1 2 2 103
+GASKET-MIX HOPPER 038375 1 1 000
+GASKET-MIX HOPPER 038474 1 1 000
Parts List
120117
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
KNOB-MIX HOPPER 025429 1 1 2 2 103
Parts List
COVER-MIX HOPPER 041682-GRY 2 103
DECAL-DECORATIVE SOFTECH 033230 1 1 000
DECAL-DECORATIVE SOFTECH 032919 1 1 000
DECAL-DECORATIVE SOFTECH 045812 1 000
+ Available Separately
DECAL-HEATER SWITCH 036551 1 000 ”ON-OFF”
DECAL-CLEAN & SANITIZE 019029 1 1 1 1 1 000
DECAL-POWER SWITCH - ON/OFF (OLD) 32484 1 1 000 PRIOR TO J8080000 132
DECAL-POWER SWITCH - ON/OFF 032484 1 1 1 000
DECAL-TROUBLESHOOTING 038374 1 1 1 1 1 000
DECAL-WARNING 036529 3 3 3 3 3 000
DEFLECTOR-BLOWER EXHAUST 046586 1 1 1 103
DEFLECTOR-BLOWER EXHAUST 047912 1 103
DIAGRAM-WIRING 052613- 1 000 J8108583/UP (COPELAND) 136
DIAGRAM-WIRING 050318- 1 1 000 750 - PRIOR TO J8108583 136
44
DIAGRAM-WIRING 046585- 1 1 000
DIAGRAM-WIRING 048199- 1 000
DOOR A.-FREEZER X51531-10 1 1 103
+BEARING-FRONT 050216 1 1 000
+CAP-DESIGN 014218 1 1 000
+GASKET-DOOR 048926 1 1 000
DOOR A.-FREEZER X51532-12 1 1 1 103
+BEARING-FRONT 050216 2 2 2 000
+CAP-DESIGN 014218 3 3 3 000
DECAL-DOOR 021521 1 1 1 000
+GASKET-DOOR 048926 2 2 2 000
DRYER-CAPILLARY 047699 1 1 1 1 1 000 AUXILIARY
DRYER-FILTER 048901 1 1 2 2 2 000
GASKET-FREEZER DOOR 048926 1 1 2 2 2 000
GEAR-REDUCER 021286 1 1 2 2 2 212
GUIDE A.-DRIP PAN X50752 1 103
GUIDE A.-DRIP PAN X28863 1 103
GUIDE A.-DRIP PAN X28699 1 1 103
+ Available Separately
HANDLE A.-ADJUSTABLE DRAW X33687 3 3 3 103 J7090000/UP REPLACES X26996 121
HANDLE-DRAW 028804 3 3 3 103
SCREW-ADJUSTABLE 033662 3 3 3 103 STAINLESS 121
O-RING 015872 3 3 3 000
HOOD ASSEMBLY X35565 1 1 103
45
CAP-DESIGN 014218 1 1 000
GASKET-DOOR 048926 1 1 000
O-RING 018572 4 4 000 AIR TUBE
O-RING 014402 2 2 000 DRAW VALVE
O-RING 016272 1 1 000 PIVOT PIN
O-RING 016137 3 3 000 PRIME PLUG & AIR ORIFICE
SEAL 032560 1 1 000 DRIVE SHAFT
TOOL-O-RING REMOVAL 048260-WHT 1 1 000
KIT A.-TUNE-UP X49463-4 1 1 1 000
BEARING-FRONT 050216 2 2 2 000
CAP-DESIGN 014218 3 3 3 000
GASKET-DOOR 048926 2 2 2 000
O-RING 018572 8 8 8 000 AIR TUBE
O-RING 014402 5 5 5 000 DRAW VALVE
O-RING 016272 1 1 1 000 PIVOT PIN
O-RING 016137 6 6 6 000 PRIME PLUG & AIR ORIFICE
SEAL 032560 2 2 2 000 DRIVE SHAFT
SEAL-DRAW VALVE 034698 1 1 1 000 H-RING
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
TOOL-O-RING REMOVAL 048260-WHT 1 1 1 000
Parts List
LABEL-SWITCH-POWER-OFF/ON SYMBOL 052632 1 1 000 J8080000/UP-ON POSITION ON R/S 132
LABEL-WARN-COVER 051433 4 5 6 7 5 000
LEG (4” w/O-RING) 013458 4 103
LID-W/LADLE 036575 2 103
+ Available Separately
LOUVER-SIDE (LEFT) 013631 1 103 LEFT
LOUVER-SIDE 017471 2 2 2 2 103
LUBRICANT-TAYLOR 4 OZ. 047518 1 1 1 1 1 000
MAN-OPER 028754-M 1 1 1 1 1 000
MOTOR-BEATER 021522- 1 1 2 2 2 212
CAPACITOR-RUN (230-60-1) 027087 1 1 2 2 2 103 MAGNETEK/CENTURY 230-30-1
CAPACITOR-RUN (230-60-1) 036084 1 1 2 2 2 103 LEESON 230-30-1
CAPACITOR-START (230-60-1) 028315 1 1 2 2 2 103 MAGNETEK/CENTURY 230-30-1
CAPACITOR-START (230-60-1) 045862 1 1 2 2 2 103 LEESON 230-30-1
MOTOR-FAN (CONDENSER) 051744-27 1 103 J8108583/UP (COPELAND) 136
46
MOTOR-FAN (CONDENSER) 041401-27 1 103 PRIOR TO J8108583 136
+BLADE-FAN (12” PUSH) 047279 1 103
MOTOR-FAN (w/BLADE) 027309- 1 1 1 1 1 103 SHR
+BLADE-FAN 033499 1 1 1 1 1 103 SHR
NUT-JAM-5/16-24 029639-BLK 3 3 3 000 J7090000/UP 121
NUT-STUD (HANDSCREW) 021508 4 4 103 HANDSCREW
NUT-STUD (LONG) 034382 2 2 2 103 LONG
NUT-STUD (SHORT) 034383 2 2 2 103 SHORT
ORIFICE-AIR 022465-100 1 1 2 2 2 103
O-RING 016137 1 1 2 2 2 000
PAIL 023348 1 000 6 QT. / 5.7 LITER
PAIL 013163 1 1 1 1 000 10 QT. / 9.5 LITER
PAN-DRIP 050766 1 103
PAN-DRIP - 11-5/8” LONG 027503 1 103
PAN-DRIP 17-1/4” LONG 027504 1 1 103
PAN-DRIP 035034 1 103
PAN A.-HINGED DRIP X41844 1 103
PANEL-REAR 020891 1 103
+ Available Separately
PANEL-SERVICE 047170 1 103
PANEL-SERVICE 046584 1 103
PANEL-SERVICE 047077 1 103
PANEL-SERVICE 041856 1 103
PANEL-UPPER RIGHT SIDE 042317 1 103
47
PANEL-UPPER SIDE 024426 1 2 103
PANEL-UPPER SIDE-LEFT 028822 1 1 103
PANEL A.-LOWER SIDE-LEFT X46447 1 1 1 103
PANEL A.-LOWER SIDE-RIGHT X46448 1 1 1 103
PANEL A.-FRONT X50754 1 103
PANEL A.-FRONT X33237 1 103
PANEL A.-FRONT X32956 1 103
PANEL A.-FRONT X42539 1 103
HEATER-STRIP 023953-4 1 103
LABEL-TEMPERATURE ADJUSTMENT 030994 1 000
PLUG-DRAIN 023953-5 1 103
O-RING 016369 1 000
THERMOSTAT-ADJUSTABLE 049993 1 103
THERMOSTAT-HI LIMIT 049992 1 103
PANEL A.-FRONT X41820 1 103
PIN A.-PIVOT X22820 1 1 103
+O-RING 016272 1 1 000
PIN A.-PIVOT X20683 1 1 1 103
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
+O-RING 016272 1 1 1 000
Parts List
PLATE-DECORATIVE 033239 1 1 103
PLATE-DECORATIVE 032961 1 1 103
PLATE-DECORATIVE 041854 1 103
PLUG-DRIP TRAY HOLE 029595 1 1 000
+ Available Separately
PLUG-PRIME 028805 1 1 2 2 2 103
+O-RING 016137 2 2 4 4 4 000
PROBE A.-MIX X30922 1 1 2 2 2 103
+DISC 030965 1 1 2 2 2 103
+SPACER 030966 1 1 2 2 2 103
PROBE A.-THERMISTOR - HOPPER X50717 1 1 1 1 1 103 794 - J8110000/UP 136
PROBE A.-THERMISTOR - HOPPER X34466 1 103 PRIOR TO J8110000 136
PROBE A.-THERMISTOR - BARREL X31602 1 1 2 2 2 103
PULLEY (BEATER MOTOR) 016403 1 1 2 2 2 103 BEATER MOTOR
PULLEY (GEAR) 027822 1 1 2 2 2 103 GEAR
48
PUMP-TOPPING 036623 2 103
BALL 032752 4 000
BODY-VALVE-SYRUP PUMP 048166 2 103
O-RING-1-5/16 OD 048149 2 000
O-RING-1” OD 048148 2 000
COLLAR-GAGING-1/202 035514 2 103
CYLINDER-SYRUP PUMP 051065 2 103
INSERT-PLUNGER 032758 2 103
KNOB-PLUNGER (w/O-RING) 032762- 2 103 032762-BRN - 032762-TAN
+O-RING 016369 2 000
LID-PUMP 036822 2 103
NUT-PLUNGER 036577 2 103
NUT-SPOUT 036821 2 103
PLUNGER 036578 2 103
SEAL ASSEMBLY (w/O-RING) X33057 2 103
+O-RING 019330 2 000
SPRING-PLUNGER 032761 2 000
TUBE-DISCHARGE 050912 2 103
+ Available Separately
SANITIZER-KAY-5 041082 1 1 1 1 1 000
SHAFT-BEATER DRIVE 032564 1 1 2 2 2 103
+SEAL-DRIVE SHAFT 032560 1 1 2 2 2 000
SHELL A.-INSULATED X50745 1 512
SHELL A.-INSULATED X49785 1 512
49
SHIELD-SPLASH 022765 1 103
STARTER-BEATER LINE 041950- 1 1 2 2 2 103
OVERLOAD-THERMAL 047150- 1 1 2 2 2 103
SWITCH-PRESSURE 405 PSI (A/C) - NEW 052663 1 103 J8108583/UP (COPELAND) 136
SWITCH-PRESSURE 440 PSI (A/C) 048230 1 1 2 2 2 103 750 - PRIOR TO J8108583 136
SWITCH-TOGGLE (POWER SWITCH) 024295 1 1 103
SWITCH-TOGGLE (POWER SWITCH) 037394 1 1 1 103
SWITCH-TOGGLE (HEATER SWITCH) 012626 1 103
SWITCH A.-DRAW X33322-SER 1 1 103
ARM A.-SWITCH X33326 1 1 103
BRACKET A.-SWITCH X43722 1 1 103
E-RING 049178 1 1 000
PIN-PIVOT 015478 1 1 103
SPRING-LEFT RETURN 041660 1 1 103
SPRING-RIGHT RETURN 041661 1 1 103
SWITCH-MICRO 028889 1 1 103
SWITCH A.-DRAW X38547 1 1 1 103
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
ARM-SWITCH-LEFT 038649 1 1 1 103
Parts List
ARM-SWITCH-RIGHT 038650 1 1 1 103
BRACKET A.-SWITCH X38252 1 1 1 103
E-RING 032190 4 4 4 000
PIN-PIVOT 038484 1 1 1 103
+ Available Separately
ROD-SPRING RETAINER 038254 1 1 1 103
SPRING-EXTENSION 038922 2 2 2 103
SPRING-LEFT RETURN 038923 1 1 1 103
SPRING-RIGHT RETURN 038924 1 1 1 103
SWITCH A.-DRAW X39269 1 1 1 103
BRACKET-SWITCH 039264 1 1 1 103
SWITCH-MIRCO 039252 2 2 2 103
TRAY-FRONT DRIP 013690 1 1 103
TRAY-FRONT DRIP 014533 1 1 103
TRAY-FRONT DRIP 020157 1 103
50
TRIM-FRONT 020889 1 103
TRIM-LEFT REAR CORNER 020678 1 103
TRIM-LEFT REAR CORNER 020882 1 103
TRIM-LEFT REAR CORNER 013761 1 1 103
TRIM-LEFT REAR CORNER 041852 1 103
TRIM-RIGHT REAR CORNER 020677 1 103
TRIM-RIGHT REAR CORNER 020883 1 103
TRIM-RIGHT REAR CORNER 013663 1 1 103
TRIM-RIGHT REAR CORNER 041853 1 103
TUBE A.-AIR X29429-2 1 1 2 2 2 103
+O-RING 018572 4 4 8 8 8 000
VALVE-ACCESS 047016 2 1 2 2 2 103
VALVE-ACCESS 044455 1 1 2 103 750 W/BRISTOL COMPRESSOR 136
VALVE-ACCESS 043232 1 2 2 103
VALVE-ACCESS 044404 1 1 1 1 1 103
VALVE-ACCESS 029406 1 1 1 1 103
VALVE-AUTOMATIC EXPANSION 046365 1 1 2 2 2 103
+BOOT-EXPANSION VALVE 050900 1 1 2 2 2 000
+ Available Separately
OPTIONAL FEATURES
AIR/MIX PUMP
BEARING-FRONT 023262 1 000 use without shoes
BEARING-FRONT 050348 1 2 000 use w/shoes 050346/050347
SHOE-FRONT HELIX-REAR 050346 1 2 000 use with 050348 bearing
51
CAPACITOR-START (PUMP) 037251- 1 2 103
DECAL-CLEAN AND SANITIZE 042170 1 1 000
DECAL-DECORATIVE 033231 1 000
DECAL-DECORATIVE 033232 1 000
GASKET-HOPPER 038375 1 2 000
GUIDE A.-DRIP PAN-PUMP X48433 1 103 hopper pump
HOOD ASSEMBLY X41996 1 103
HOOD 013667 1 103
KIT A.-TUNE-UP X49463-9 1 000
BAND-CHECK (LIQUID VALVE BODY) 020050 2 000
BAND-CHECK (LIQUID VALVE BODY) 033215 1 000
BEARING-FRONT (FREEZER DOOR) 023262 1 000 use without shoes
BEARING-FRONT (FREEZER DOOR) 050348 1 000 use w/shoes 050346/050347
SHOE-FRONT HELIX-REAR 050346 1 000 use with 050348 bearing
SHOE-FRONT HELIX-FRONT 050347 1 000 use with 050348 bearing
CAP-DESIGN (FREEZER DOOR) 014218 1 000
GASKET-DOOR 048926 1 000
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
O-RING (PRIME PLUG) 016137 3 000
Parts List
O-RING (DRAW VALVE) 014402 2 000
O-RING (PUMP DRIVE SHAFT) 008904 1 000
O-RING (LIQUID VALVE BODY) 018664 1 000
O-RING (LVB & PISTON) 020051 3 000
+ Available Separately
O-RING (MIX INLET TUBE) 015835 1 000
O-RING (MIX FEED TUBE) 016132 2 000
O-RING (PIVOT PIN) 016272 1 000
POPPET-RUBBER 022473 1 000
SEAL (AIR INLET FITTING) 045327 1 000
SEAL (BEATER DRIVE SHAFT) 032560 1 000
O-RING (PUMP DRIVE SHAFT) 048632 2 000
SPRING 022456 1 000
KIT A.-TUNE-UP X49463-19 1 000
BAND-CHECK (LIQUID VALVE BODY) 020050 4 000
52
BAND-CHECK (LIQUID VALVE BODY) 033215 2 000
BEARING-FRONT (FREEZER DOOR) 050348 2 000 023262 used without shoes
CAP-DESIGN (FREEZER DOOR) 014218 3 000
GASKET-DOOR 048926 2 000
O-RING (PRIME PLUG) 016137 4 000
O-RING (DRAW VALVE) 014402 7 000
O-RING (DRIVE CRANK) 008904 2 000
O-RING (LIQUID VALVE BODY) 018664 2 000
O-RING (LVB & PISTON) 020051 6 000
O-RING (MIX INLET TUBE) 015835 2 000
O-RING (MIX FEED TUBE) 016132 4 000
O-RING (PIVOT PIN) 016272 1 000
O-RING (PUMP DRIVE SHAFT) 048632 4 000
POPPET-RUBBER 022473 2 000
SEAL-DRAW VALVE 034698 1 000
SEAL (AIR INLET FITTING) 045327 2 000
SEAL (BEATER DRIVE SHAFT) 032560 2 000
SHOE-FRONT HELIX-REAR 050346 2 000 use with 050348 bearing
+ Available Separately
MOTOR-REDUCER 036955-34 1 2 103
OVERLOAD (MOTOR REDUCER) 044464 1 2 103
PAN-DRIP 048435 1 103 HOPPER PUMP
PAN A.-DRIP X38198 1 103
PANEL-REAR 048203 1 103
53
+CLIP-PUMP 044641 1 2 103
CYLINDER A.-PUMP X44755 1 2 103
O-RING (LIQUID VALVE BODY) 018664 1 2 000
O-RING (LVB & PISTON) 020051 3 6 000
PIN A.-PUMP X36950 1 2 103
PISTON 045319-B 1 2 103
POPPET-RUBBER 022473 1 2 000
SPRING 022456 1 2 000
TUBE A.-MIX INLET X45318 1 2 103
O-RING 015835 1 2 000
SEAL 045327 1 2 000
RELAY (MOTOR REDUCER) 039725- 1 2 103
SHAFT A.-DRIVE X39084 1 2 103
O-RING (DRIVE CRANK) 008904 1 2 000
O-RING (DRIVE CRANK) 048632 2 4 000
SHELL A.-INSULATED X50332 1 512
SHELL A.-INSULATED X50376 1 512
SLEEVE A.-MIX PUMP X45012 1 2 103
Parts List
DESCRIPTION PART 750 751 754 774 794 WARR. REMARKS PARTS
NUMBER QTY. QTY. QTY. QTY. QTY. CLASS UPDATE
+NUT-PUMP SLEEVE 036933 1 2 103
Parts List
TUBE A.-MIX FEED X44666 1 103
+O-RING 016132 2 000
TUBE A.-FEED (LEFT) X44662 1 103
TUBE A.-FEED (RIGHT) X44664 1 103
+ Available Separately
O-RING-FEED TUBE 016132 4 000
VIDEO-TRAINING 047247- 1 1 000
WATER COOLED
BLOWER 012796- 1 1 1 1 103
+GUARD-BLOWER 022505 1 1 1 1 103
CONDENSER 049309 1 103
CONDENSER 048287 1 2 2 2 103
MOTOR-FAN 015184- 1 103
+BLADE-FAN (10” PUSH) 013043 1 103
PANEL A.-LOWER SIDE (R & L) X24424 2 2 2 2 103
54
SWITCH-PRESSURE 048231 1 1 2 2 2 103
VALVE-WATER 046686 1 1 2 2 103
+ Available Separately
BLOCK-TERMINAL (220/440-50-3) 039424 1 1 2 2 2 103
CAPACITOR-RUN (BEATER MOTOR) 023606 1 1 2 2 2 103 CENTURY/MAGNETEK
CAPACITOR-RUN (BEATER MOTOR) 035765-27 1 1 2 2 2 103 LEESON
CAPACITOR-START (BEATER MOTOR) 028315 1 1 2 2 2 103 CENTURY/MAGNETEK
CAPACITOR-START (BEATER MOTOR) 026659 1 1 2 2 2 103 LEESON
COMPRESSOR (MAIN - HP62) 048727- 1 512 BRISTOL
55
CAPACITOR-START (230-50-1) 031790 1 2 103
RELAY-START (230-50-1) 038146 1 2 103
COMPRESSOR-MAIN (HP62) 047519- 2 512 TECUMSEH
CAPACITOR-RUN (230-50-1) 029439 2 103
CAPACITOR-START (230-50-1) 036048 2 103
RELAY-START (230-50-1) 036047 2 103
MOTOR-FAN 047178-34 1 103
BLADE-FAN (12” PUSH) 047279 1 103
PULLEY (BEATER MOTOR) 011545 1 1 2 2 2 103
Parts List
Model 791
121031
DESCRIPTION PART 791 WARR. REMARKS
NUMBER QTY. CLASS
Parts List
079127RW00 - 208- 230V 60HZ 1PH, 079133RW00 - 208- 230V 60HZ 3PH - 3 WIRE, W/C- BRISTOL (R404A), ROHS COMPLIANT - STD
ARM- DRAW SWITCH- LEFT 069166 1 103
ARM- DRAW SWITCH- RIGHT 069167 1 103
+ Available Separately
BEARING- FRONT 050216 2 000
BEARING- REAR SHELL 031324 2 000
+GUIDE- DRIP SEAL 028992 2 000
+NUT- BRASS BEARING 028991 2 000
+WASHER- BEARING LOCK 012864 2 000
BEATER ASSEMBLY X31761 2 103
+BLADE- SCRAPER 035174 12 000
BELT- AX31 041575 4 000
BLOCK- TERMINAL 2P .25 SPADE 069015 1 103
BLOWER- 100 CFM 012796- 27 1 103
56
+GUARD- BLOWER 022505 1 103
BOARD- LOGIC- GEN 2.10- W/SEL DI X69570SER2 2 212 REPLACES X36641SER2
BOARD- POWER X69574- SER 2 212 REPLACES X32326- SER
BRUSH- BLACK (1” X 2”) 013071 1 000
BRUSH- DOUBLE END 013072 1 000
BRUSH- WHITE (1” X 2”) 013073 1 000
BRUSH- WHITE (3” X 7”) 023316 1 000
CABLE- RIBBON 069474- 60 2 103 REPLACES 032445
CAP- DESIGN 014218 3 000
CASTER- 4” SWV 5/8” STEM 018794 2 103
CASTER- 4” SWV 5/8” STEM W/BRAKE 034081 2 103
CHANNEL- REAR BEARING DRIP *794 041819 1 103
COMPRESSOR L64A113BBCA- 40 048259- 27H 1 512 208- 230V 60HZ 1PH
CAPACITOR- START 189- 227UF/33 033044- 1 1 103
CAPACITOR- RUN 25UF/440V 037431 1 103
RELAY- START- COMPRESSOR 062363 1 103
COMPRESSOR L63A113DBLA- 40W CCH 048259- 33H 1 512 208- 230V 60HZ 3PH - 3 WIRE
+ Available Separately
CONDENSER- AUXILIARY 027155 1 103
CONDENSER- WC- COAX 047540 1 103
CORD- POWER 250V 30A *791* 069576- 27 1 1 208- 230V 60HZ 1PH
CORD- POWER 250V 20A *791* 069576- 33 1 1 208- 230V 60HZ 3PH - 3 WIRE
COUPLING- DRIVE 012721 2 103
57
DIAGRAM- WIRING *791* 069543- 27 1 000 208- 230V 60HZ 1PH
DIAGRAM- WIRING *791* 069543- 33 1 000 208- 230V 60HZ 3PH - 3 WIRE
DOOR A.- 3 SPOUT X51532- 12 1 103
+BEARING- FRONT 050216 2 000
+DECAL- DOOR- 3 SPOUT- TWIN TWIS 021521 1 000
+GASKET- DOOR HT 4”- DOUBLE 048926 2 000
+HANDLE A.- DRAW ADJUSTABLE X55096 3 103
+LABEL- FLAVOR 036693 1 000
+PLUG- PRIME 028805 2 103
+O- RING- 3/8 OD X .070W 016137 4 000
+ROD A.- PIVOT X20683 1 103
+O- RING- 5/16 OD X .070W 016272 1 000
+VALVE A.- DRAW X69539 3 103
+O- RING- 13/16 OD X .103W 019330 6 000
DRYER- CAPILLARY 047699 1 000 AUXILIARY
DRYER- FILTER 3/8 X 3/8SOL HP62 049154 1 000
FUSE- .063A- 250V- 5X20MM- SLO BLO 051272 2 000
Parts List
GASKET- FREEZER DOOR 048926 2 000
DESCRIPTION PART 791 WARR. REMARKS
NUMBER QTY. CLASS
GEAR- REDUCER 021286- SER 2 212
Parts List
GUIDE A.- DRIP PAN X45691 1 103
HARNESS- WIRE- DANFOSS *794* 067147- 27 1 103
HARNESS- WIRE- CNTRL SWITCH*79 069601 1 103
HARNESS- WIRE- CONTROL- R *791* 069633- 27R 1 103 208- 230V 60HZ 1PH
+ Available Separately
HARNESS- WIRE- CONTROL- R *791* 069633- 33R 1 103 208- 230V 60HZ 3PH - 3 WIRE
HARNESS- WIRE- CONTROL- L *7 069633- 27L 1 103 208- 230V 60HZ 1PH
HARNESS- WIRE- CONTROL- L *791* 069633- 33L 1 103 208- 230V 60HZ 3PH - 3 WIRE
HARNESS- WIRE- BEATER MTR*C 066440- 27G 2 103 208- 230V 60HZ 1PH
HARNESS- WIRE- BEATER MTR*C71 066440- 33G 2 103 208- 230V 60HZ 3PH - 3 WIRE
HARNESS- WIRE- COMPRESSOR*794* 068644- 33 1 103 208- 230V 60HZ 3PH - 3 WIRE
HARNESS- WIRE- SOL VLV*791* 069634 1 103
INTERLOCK A.- DOOR X65658 * 103 SEE - SWITCH A.- REED INTERLOCK DOOR
KIT A.- COVER- HOPPER*DUAL*GRAY X68150 1 103
COVER- HOPPER- 14 QT- GRAY 041682- GRY 2 103
58
KIT A.- TUNE UP- 3 SPOUT- NO X49463- 4 1 000
BEARING- FRONT 050216 2 000
CAP- DESIGN 1.010”ID- 6 POINT 014218 3 000
GASKET- DOOR HT 4”- DOUBLE 048926 2 000
KIT A.- SILICON O- RINGS X69575 1 000
O- RING- 13/16 OD X .103W 019330 6 000
LABEL- INSTRUCTION O- RING USA 069561 1 000
O- RING- .643 OD X .077W 018572 8 000
O- RING- 3/8 OD X .070W 016137 6 000
O- RING- 5/16 OD X .070W 016272 1 000
O- RING- 7/8 OD X .103W 014402 6 000
SEAL- DRAW VALVE 034698 1 000
SEAL- DRIVE SHAFT 032560 2 000
TOOL- O- RING REMOVAL- FREEZER 048260- WHT 1 000
LABEL- 3PH MTR PROT/1PH C- ENG/S 025949 1 000 208- 230V 60HZ 3PH - 3 WIRE
LABEL- ATTN SVC ENG 015068 2 000
LABEL- CK MTR ROTATE- CW- ENG/SPN 020090 1 000 208- 230V 60HZ 3PH - 3 WIRE
LABEL- CAUTION- GRD- PERM- ENG/SP 032164 1 000
+ Available Separately
LABEL- WARN- ELEC- TW- SMALL 032718 1 000
LABEL- WIRING SINGLE PHASE 036880- 2 1 000 208- 230V 60HZ 1PH
LUBRICANT- TAYLOR 4 OZ. 047518 1 000
MAN- OPER 028754- M 1 000
MOTOR A.- FAN X69411- 27 2 103
59
ORIFICE- AIR 022465- 100 2 103
O- RING 016137 4 000
PAIL- 10 QT. 013163 1 000 10 QT. / 9.5 LITER
PAN A.- HINGED DRIP X41844 1 103
PAN- DRIP 035034 1 103
PANEL A.- FRONT *794* X41820- SP3 1 103
PANEL- REAR 041855 1 103
PANEL- SERVICE 064000 1 103
PANEL- SIDE *794* WC 069038 2 103
PLATE- DECORATIVE 041854 1 103
PLUG- HOLE 7/8 DIA. BLACK 010077 2 000
PLUG- PRIME 028805 2 103
PLUG- HOLE 1- 3/4 DIA. 027132 1 000
PLUG- HOLE 1 DIA- BLK PLASTIC 027143 2 000
PLUG- HOLE 1- 3/8 DIA.- BLACK 053361 2 000
PROBE A.- MIX X30922 2 103
+DISC- PROBE *SQ HOLE* 030965 2 103
Parts List
+SPACER- PROBE *SQ HOLE* 030966 2 103
140718
DESCRIPTION PART 791 WARR. REMARKS
NUMBER QTY. CLASS
130122
PROBE A.- MIX OUT- SQUARE HOLE X41348 2 103
Parts List
SPACER- PROBE- SQUARE HOLE- 7/8 041346 2 103
SPACER- PROBE- ROUND HOLE- 5/8DIA 041347 2 103
PROBE A.- THERMISTOR - BARREL X31602 2 103
PROBE A.- THERMISTOR - HOPPER X50717 1 103
+ Available Separately
PULLEY- 2AK22 X .625- .6265 016403 2 103 BEATER MOTOR
PULLEY- 2AK74- 5/8 027822 2 103 GEAR
RELAY- 3 POLE- 20A- 208/240 50/60 066795- 33 1 103
RELAY- DPDT 100UA TO 7A 052111- 76 2 103
RELAY- DPDT 100UA TO 7A 1/8HP 052111- 03 1 103
RELAY- START- COMPRESSOR- TL3G 047702- 27 1 103
SANITIZER- STERA SHEEN - GREEN 055492 1 000
SHAFT- BEATER DRIVE 032564 2 103
+SEAL- DRIVE SHAFT 032560 2 000
SHELL A.- INSULATED*794*MIX OUT X68678- SP4 1 512
60
+STUD- NOSE CONE 068410 4 103
SPRING- EXTENSION.467X.062X1. 069392 2 103
SPRING- RETURN- LEFT- TWIN TWIS 038923 1 103
SPRING- RETURN- RIGHT- TWIN TWIST 038924 1 103
SPRING- COMP .970 X .115 X 2.00 025707 4 000 BEATER MOTOR
STARTER- 1 PHASE 6.3 TO 10 066794- 27K 2 103 208- 230V 60HZ 1PH
OVERLOAD- THERMAL- 1P- 6.3/10A 067461- 1K 2 103
STARTER- 3 PHASE 4 TO 6.5 AMP 066794- 33J 2 103 208- 230V 60HZ 3PH - 3 WIRE
OVERLOAD- THERMAL- 3P- 4.0/6.5A 067461- 3J 2 103
SWITCH A.- DRAW *SELF CLOSING X69821 1 103
ARM- DRAW SWITCH- LEFT 069166 1 103
ARM- DRAW SWITCH- RIGHT 069167 1 103
BRACKET A.- SPRING- RETURN X69481 1 103
BRACKET A.- SWITCH *338/39/75 X69388 1 103
E- RING 1/4 BLACK PHOS 032190 3 000
PIN- PIVOT- DRAW SWITCH 038484 1 103
ROD- SPRING RETAINER 038254- SP 1 103
SCREW- 8- 32X3/8 SLOT HEX WASH 039267 2 000
+ Available Separately
SWITCH- LEVER- SPDT- 11A- 125- 277V 039252 2 103
SWITCH A.- REED INTERLOCK DOOR X65658 1 103
SWITCH- REED*DOOR INTERLOCK*6 056771 1 103
SWITCH- PRESSURE 350 PSI- SOLDER 048231 1 103
SWITCH- REED*DOOR INTERLOCK*68” 056771 1 103
61
VALVE A.- DRAW X69539 3 103
+O- RING- 13/16 OD X .103W 019330 6 000
VALVE- ACCESS- 1/4FL X 1/4SOLDER 044404 1 103
VALVE- ACCESS- 1/4 MFLX1/4 S- 90 047016 2 103
VALVE- ACCESS- 1/4FL X 3/8SOLDER 043232 1 103
VALVE- EPR 1/4S 022665 1 103
VALVE- EXP- AUTO- 1/4S X1/4 FPT 046365 2 103
VALVE- SOLENOID 7/16 ORF 5/8 ODF 048626- 27 2 103
VALVE- SOLENOID 7/64ORF X 1/4S 043449- 27 2 103
Parts List
120824
DESCRIPTION PART 791 WARR. REMARKS
NUMBER QTY. CLASS
Parts List
079133RWEW, 208- 230V 60HZ 3PH - 3 WIRE, W/C- BRISTOL- (R404A), ROHS COMPLIANT, ADJUSTABLE FEED TUBE
DECAL- DOOR- MENCHIES- 794 067494 1 000
DECAL- DEC- MENCHIES*791*MIX OUT 069977 1 000
DOOR A.- 3 SPOUT *MENCHES* X51532- 24 1 103
+ Available Separately
+BEARING- FRONT 050216 2 000
+DECAL- DOOR- MENCHIES- 794 067494 1 000
+GASKET- DOOR HT 4”- DOUBLE 048926 2 000
+HANDLE A.- DRAW ADJUSTABLE X55096 3 103
+LABEL- FLAVOR 036693 1 000
+PLUG- PRIME 028805 2 103
+O- RING- 3/8 OD X .070W 016137 4 000
+ROD A.- PIVOT X20683 1 103
+O- RING- 5/16 OD X .070W 016272 1 000
+VALVE A.- DRAW X69539 3 103
+O- RING- 13/16 OD X .103W 019330 6 000
62
KIT A.- TUNE UP- 3 SPOUT- NON HT X49463- 4A 1 000
KIT A.- SILICON O- RINGS X69575 1 000
O- RING- 13/16 OD X .103W 019330 6 000
LABEL- INSTRUCTION O- RING USA 069561 1 000
CAP- DESIGN 1.010”ID- 6 POINT 014218 3 000
O- RING- 7/8 OD X .103W 014402 6 000
O- RING- 3/8 OD X .070W 016137 6 000
O- RING- 5/16 OD X .070W 016272 1 000
O- RING- .291 ID X .080W 018550 6 000
O- RING- .643 OD X .077W 018572 4 000
SEAL- DRIVE SHAFT 032560 2 000
SEAL- DRAW VALVE 034698 1 000
TOOL- O- RING REMOVAL- FREEZER 048260- WHT 1 000
GASKET- DOOR HT 4”- DOUBLE 048926 2 000
BEARING- FRONT 050216 2 000
TUBE A.- FEED- INNER- AIR/MIX X67103 2 103
079133RWFD, 208- 230V 60HZ 3PH - 3 WIRE, W/C- BRISTOL- (R404A), ROHS COMPLIANT- REAR MIX LIGHTS, ADJ FEED TUBE- REAR PULL HANDLE
ADJ FEED TUBE- REAR PULL HANDLE
COVER- BOX- LIGHT- MIX LVL- R 080515 1 103
HANDLE- STNLS FLUSH PULL 019043 2 103
HARNESS- WIRE- RMLL*791* 080516 1 103
+ Available Separately
HARNESS- WIRE- CNTRL SWITCH 069601- SP 1 103
LIGHT- AMBER- ROUND- 250V- MI 080039- 27 2 103
LIGHT- AMBER- ROUND- 250V- MI 080040- 27 2 103
PANEL- SIDE *794*WC*LEFT 069038- SP 1 103
PANEL- SIDE *794*WC*RIGHT 069038- SP1 1 103
63
TRIM- CORNER- REAR- R *794* 068689- SP1 1 103
TUBE A.- FEED- INNER- AIR/MI X67103 2 103
TUBE A.- FEED- OUTER- HT X67104 2 103
079133RWEX, 208- 230V 60HZ 3PH - 3 WIRE, W/C- BRISTOL- (R404A), ROHS COMPLIANT, HOPPER AGITATOR- REAR MIX LIGHT- YOGURTLAND
ADAPTOR A.- CASTER X18915 4 103
BLADE A.- AGITATOR *794* X56591- SP 2 103
BLOCK- TERMINAL 3P 20A, 300V 051331 1 103
BUSHING- SNAP 1- 5/16ID X 1- 1/ 017008 2 103
BUSHING- SNAP 5/8ID X 3/4OD- B 017462 2 000
BUSHING- SNAP 3/4ID X 1”OD BL 053144 2 103
CONTROL- MIX LEVEL- ROHS 065840 2 103
CASTER- 4” SWV 5/8 STEM W/ 034081 2 103
CASTER- 4” SWV 5/8 STEM X 018794 2 103
CD- OPS TRAIN 794 YOGURTLA 068592- YGL 1 000
COVER- BOX- LIGHT- MIX LVL- R 080515 1 103
DOOR A.- FREEZER 3 SPOUT T X49461- 37S 1 103
Parts List
130122
+BAFFLE A.- LONG 4 IN W/RAD TH X50882 2 103
DESCRIPTION PART 791 WARR. REMARKS
NUMBER QTY. CLASS
+BEARING- FRONT 050216 2 000
Parts List
+GASKET- DOOR HT 4”- DOUBLE 048926 2 000
+HANDLE A.- DRAW *794* WHITE X81010- SP 3 000 PULL DOWN HANDLE 12/10/12 & UP
+LABEL- FLAVOR 036693 1 000
+O- RING- 13/16 OD X .103W 019330 6 000
+ Available Separately
+O- RING- 3/8 OD X .070W 016137 4 000
+O- RING- 5/16 OD X .070W 016272 1 000
+PLUG- PRIME 028805 2 103
+ROD A.- PIVOT X20683 1 103
+VALVE A.- DRAW X69539 3 103
HANDLE- STNLS FLUSH PULL 019043 2 103
HARNESS- WIRE- CAP- AGIT*791* 080517 1 103
HARNESS- WIRE- CNTRL SWITCH 069601- SP 1 103
HARNESS- WIRE- RMLL*791* 080516- G 1
SOCKET- RELAY- FOR USE W/05211 052112 4 103
64
BLOCK- TERMINAL 2P .25 SPADE 069015 2 103
HARNESS- WIRE- CAP- AGIT*791* 080517 1 103
HARNESS- WIRE- SWITCH- AGIT* 069407 1 103
SWITCH- TOGGLE- SPST- 3/4 HP/25 012626 2 103
HOUSING A.- AGITATOR *C708 X56586- 03 2 103
BODY- AGITATOR HOUSING *C708* 056588 1 103
CAP- AGITATOR HOUSING 080827 1 103
MAGNET A.- AGITATOR- INNER 066937 1 103
MOTOR- AGITATOR- 24VAC 50/60 H 050535- 03 1 103
O- RING- 1- 3/8 OD X .070W 017395 1 000
PLATE- HOLDING- AGITATOR *C708 056587 1 103
SCREW- 4- 40X1/4 SOCKET HEAD 600165 4 000
SCREW- 8- 32X3/16 SOCKET SET 006812 2 000
KIT A.- TUNE UP- 3 SPOUT- NO X49463- 4B 1 000
LABEL- SWITCH- AGIT.OFF/ON- 067719 2 000
LIGHT- AMBER- ROUND- 250V- MI 080039- 27 2 103
LIGHT- AMBER- ROUND- 250V- MI 080040- 27 2 103 M2016393 & UP
LUBRICANT- TAYLOR HI PERF 048232 1 000
+ Available Separately
PCB A.- DUAL MIX LVL- 24V X41420- SER 2 212
CHIP- SOFTWARE MIX LEVEL X40799- SER 2 103
RELAY- DPDT 100UA TO 7A 052111- 76 6 103
SHELL A.- INSULATED*794*MO*HA X68678SSP5 1 S/N M2036866 & UP
SWITCH- TOGGLE- SPST- 3/4 HP/25 012626 2 103
65
Parts List
Models 750 & 751
052613- 27
Rev. 8/10
Models 750 & 751
052613- 33
Rev. 8/10
Models 750 & 751
052613- 40
Rev. 8/10
Models 750 & 751
052613- 58
Rev. 8/10
Models 754 & 774
046585- 27
Rev. 8/10
Models 754 & 774
046585- 33
Rev. 8/10
Model 791
069543- 27
Rev. 10/12
Model 794
048199- 27
Rev. 10/12
Model 794
048199- 33
Rev. 10/12
Model 794
048199- 62
Rev. 10/12