Beruflich Dokumente
Kultur Dokumente
Key Benefits
• Loop Checkout Simplification –
the modules allow you to configure
and monitor the analog and
digital data from all of your HART
devices from a remote workstation.
All data for a channel is visible
via a single location.
• Architecture Simplification –
the field devices can be interfaced
directly to these I/O modules,
eliminating the need for additional
HART multiplexers, lowering
installation costs.
• Data Management Simplification – Leveraging the Power of New or Existing HART Field
the modules have a variety of
selectable features, such as range, Devices While Protecting Your Investments
timestamping and filter frequencies.
Highway Addressable Remote Transducer (HART) input and output
Modules are suited for control and
asset analog data and management modules provide your process automation system with full analog
applications. capability and the benefit of HART protocol in an I/O module that can
be used locally or mounted remotely. The modules offer 8 or 16 channels
Features of analog input or output data with accompanying HART
• HART Primary Value (PV), Secondary digital information.
Value (SV), Third Value (TV) and
Fourth Value (FV) are directly If you have a process application that contains HART field devices, the
available for use in control ControlLogix® HART modules enable you to leverage your existing
applications as Controller tags instrumentation investment by allowing you to:
• HART 5, 6 and 7 read/write capability
• Connect directly to HART devices without external HART multiplexers
• Pass Through support for asset
management software or extra wiring
• Device Type Manager (DTM) for use • Provide access to more field device data, such as HART Primary
with Asset Manager software Value, Secondary Value, Third Value, Fourth Value and device
• Available in conformally coated status information
versions to help protect in harsh • Manage HART devices individually that are connected directly
environments
to the modules
• Document the device wired to each channel
1756- IF16IH is a 16-channel • Meets commercial requirements for greenfield, conversion
isolated module with a and plant upgrades
dedicated HART modem
Lowering Your Operating Costs
per channel.
The ControlLogix HART modules maximize your system performance by
combining real-time HART data with standard analog data at a fraction
of the cost. Simplify commissioning, operation and maintenance with
increased insight to device status. You can use the digital data as the
foundation of your asset management system.
You can see HART device configuration and diagnostic
information in Studio 5000 Automation Engineering
& Design Environment® software. You can also view
device information and verify which device is wired to a
specific channel. The HART device tags, manufacturer and
descriptor are visible for each channel. Additionally, to aid
maintenance and troubleshooting activities, the device
status and diagnostic code is available without a handheld
device. Simply locate the device in its mounting position
and connect directly.
The FactoryTalk® AssetCentre load the software onto a computer alarms from various devices can also
software includes everything needed residing on the control network be easily monitored. The ability to
for effective asset management of and you’re ready to go. Configure, upload and download HART device
HART field devices. It includes the calibrate, tune, analyze and optimize configurations allows for faster
communication DTMs and drivers HART devices connected to 1756 replacement of failed devices to get
needed to configure and manage HART I/O modules installed in your your plant back up and running.
HART instruments attached to the PlantPAx Process Automation System
PlantPAx® Process Automation from a central location.
System. Because the asset
management software is based on FactoryTalk AssetCentre Process
the open Field Device Tool (FDT) Device Configuration provides a
standard (IEC-62453 and ISA103), you single location to perform both offline
can configure and manage any HART and online modification of the HART
device using this software. Simply device parameters. Device status and
Asset Management
FactoryTalk 1756-OF8H, -IF8H, -IF8IH,
AssetCentre -IF16H, -IF16IH, or -OF8IH FDT Technology standardizes the communication
interface between field devices and host systems to
reduce integration efforts. FactoryTalk AssetCentre
Process Device Configuration is enabled by FDT
Technology.
FactoryTalk AssetCentre optional capabilities extend
the value of your PlantPAx Process Automation System
EtherNet/IP and allow you to optimize your investments.
Allen-Bradley, ControlLogix, FactoryTalk, Listen. Think. Solve., PlantPAx, Rockwell Software, RSLogix, and Studio 5000 Automation Engineering & Design Environment are
registered trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 1756-PP016F-EN-P – November 2016 Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
Supersedes Publication 1756-PP016E-EN-P – October 2015