Beruflich Dokumente
Kultur Dokumente
hdian Standard
HEXAGON NUTS WITH FLANGE — COARSE THREAD
ICS 21.060.20
@ BIS 2005
NATIONAL FOREWORD
This Indian Standard which is identical with ISO 4161 : 1999 ‘Hexagon nuts with flange — Coarse
thread’ issued by the International Organization for Standardization ( ISO ) was adopted by the Bureau
of Indian Standards on the recommendations of the Bolts, Nuts and Fasteners Accessories Sectional
Committee and approval of the Medical Instruments, General and Production Engineering Division
Council.
The text of ISO Standard has been approved as suitable for publication as an Indian Standard without
deviations. Certain terminology and conventions are, however, not identical to those used in Indian
Standards. Attention is drawn especially to the following:
a) Wherever the words ‘International Standard’ appear, referring to this standard, they should be
read as ‘Indian Standard’.
b) Comma ( , ) has been used as a decimal marker while in Indian Standards, the current practice
is to use a point ( . ) as the decimal marker.
In this adopted standard reference appears to certain international Standards for which Indian Standards
also exist. The corresponding Indian Standards, which are to be substituted in their places, are listed
below along with their degree of equivalence for the editions indicated:
ISO 261 : 1998 ISO general IS 4218 ( Part 2 ) :2001 ISO general do
purpose metric screw threads — purpose metric screw threads:
General plan Part 2 General plan ( second
revision )
ISO 965-2 : 1998 ISO general IS 14962( Part 2 ) :2001 [S0 General do
purpose metric screw threads — purpose metric screw threads —
Tolerances — Part 2: Limits of sizes Tolerances: Part 2 Limits of sizes for
for general purpose external and general purpose external and internal
internal screw threads — Medium screw threads — Medium quality
quality
ISO 3269 : 19881) Fasteners — IS 1367 ( Part 1“7 ) :2005 Technical Technically equivalent
Acceptance inspection supply conditions for threaded steel
fasteners: Part 17 Inspection,
sampling and acceptance procedure
( fourth revision)
hciian Standard
1 Scope
This International Standard specifies the characteristics of hexagon nuts with flange, with metric coarse threads
from M5 to M20 inclusive, of product grade A for threads up to and including Ml 6 and product grade B for threads
above Ml 6.
If, in special cases, specifications other than those listed in this International Standard are required, they should be
selected from existing International Standards, for example ISO 261, ISO 898-2, .ISO 965-2, ISO 3506-2.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision,
and parties to agreements based on this International Standard are encouraged to investigate the possibility of
applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of
currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions.
[S0 261:1998, ISO general purpose metric screw threads — General plan.
ISO 898-2:1992, Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse
thread.
ISO 965-2:1998, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general
purpose external ~nd internal screw threads — Medium quality.
ISO 4759-1 :—s), Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C.
ISO 8992:1986, Fasteners — Genera/ requirements for bo/ts, screws, studs and nuts.
*
3 Dimensions
(1-j
mm
m
.
x
— .
~e
dd
Lz
a mWis the wrenching height see note to Table 1
I
I
b e=90°t01200
c $=15” to30”
d C5=15°t0250
e c is measured at dW,~in
Figure 1
2
IS 15581 :2005
ISO 4161 :1999
Table 1 — Dimensions
Dimensions in millimetres
pb
0,8 1 1,25 1,5 1,75 2 2 2,5
NOTE If the product passes the gauging given in annex A, the requirements for dimensions e, c and mw are satisfied.
3
IS 15581 :2005
ISO 4~61 :1999
See table 2.
General International
ISO 8992
requirements Standard
Tolerance 6H
Thread International
ISO 261, ISO 965-2
Standards
Property class 8 9 10 12
d< M16:A
Product grade
Tolerances d> M16:B
International
Iso 4759-1
Standard
As processed Plain
a Based on the nut height (dimension h~in) nuts to this international Standard are of style 2. However, since for style 2,
ISO 898-2 does not specify mechanical properties for all property classes and sizes as specified in this International
Standard, in some cases nuts have to be tested according to style 1.
5 Designation
EXAMPLE
A hexagon nut with flange, with thread Ml 2 and property class 10 is designated as follows:
Annex A
(normative)
The nut shall be gauged using two plain ring gauges, A and B, to demonstrate the coincidental acceptability of
hexagon height, corner fill and width across corners. Gauge A shall be placed over the nut and shall be seated on
the flange. Gauge B shall be placed on the top of the nut normal to the nut axis. The two gauges shall not be in
contact.
Gauge C is a flat feeler or ring gauge. It is used to prove that the flange thickness at the junction of the gauge with the
hexagon portion is equal to or greater than specified values. The acceptance criterion is that gauge C will fit under
gauge A without contact when the nut is seated on a flat plate.
w~
k -1 2
m
I
Key
1 Gauge A
2 Gauge B
3 Gauge C
Figure A.1
IS 15581 :2005
ISO 4161 :1999
Table A.1
Dimensions in miliimetres
Wa Ta Wb Tb Wc TC
max. min. max. min. max. min. min. min. max. min.
6
IS 15581:2005
ISO 4161:1999
NATIONAL ANNEX A
( National Foreword)
A-1 PACKAGING
The packaging of hexagon nuts with flange shall be in accordance with IS 1367 ( Part 18 ) :1996
‘Industrial fasteners —Threaded steel fasteners —Technical supply conditions: Part 18 Packaging
( third revision )’,
7
( Continued from secorfdcover)
ISO 4042 : 19891) Fasteners — IS 1367 ( Part 11 ) :2002 Technical Technically equivalent
Electroplated coatings supply conditions for threaded steel
fasteners: Part 11 Electroplated
coatings ( third revision )
As decided by the Committee additional requirements of packaging, and BIS Certification Marking are
given in National Annex A. These additional requirements are part of this standard.
For the purpose of deciding whether a particular requirement of this standard is complied with, the final
value, observed or calculated, expressing the result ~f a test or analysis, shall be rounded off in
accordance with IS 2 : 1960 ‘Rules for rounding off numerical values ( revised )’. The number of
significant places retained in the rounded off value should be the same as that of the specified value in
this standard.
— ——
1) Since revised in 1999,
z) Since revised in 2000.
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of /rrdian Standards Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of
goods and attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications maybe ~eproduced in any
form without the prior permission in writing of BIS. This does not preclude the free use, in the course
of implementing the standard, of necessary details, such as symbols and sizes, type or grade
designations. Enquiries relating to -copyright be addressed to the Director (Publications), BIS.
Amendments are issued to standards as the need arises on the basis of comments. Standards are
also reviewed periodically; a standard along with amendments is reaffirmed when such review
indicates that no changes are needed; if the review indicates that changes are needed, it is taken
up for revision. Users”of Indian Standards should ascertain that they are in possession of the latest
amendments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards : Monthly
Additions’.
This Indian Standard has been developed from Doc : No. MGP/BP 33 ( 0407 ).
. .