Beruflich Dokumente
Kultur Dokumente
1. Glasgow
Tel : 0141 764 2200
Fax : 0141 764 2201
1 2. Leeds
Tel : 0113 233 9950
Fax : 0113 233 9964
3. Birmingham
Tel : 0845 605 4333
2 Fax : 0845 605 4334
4. London
Tel : 01895 458777
3 Fax : 01895 458778
4 E-mail : cm.sales@legrand.co.uk
Customer Services :
Tel : 0845 605 4333 Fax : 0845 605 4334
E-mail : cm.sales@legrand.co.uk
CABLE MANAGEMENT SOLUTIONS CATALOGUE 2003/04
Technical :
Tel : 0845 605 5333 Fax : 0845 605 5334
E-mail : cm.quotations@legrand.co.uk
D L PASS, Fastrack, Rolfe King, Salamandre, Swifts and the Legrand logo are registered trademarks of the
Legrand group of companies.
Mosaic is a trademark of the Legrand group of companies. www.legrand.co.uk www.legrand.co.uk
CABLE TRUNKING
METAL
SURFACE
TRUNKING
SYSTEMS
Salamandre
100
CABLE TRUNKING
In addition to standard
galvanised and painted
options, a range of IP rated
and stainless steel finishes
are also available
www.legrand.co.uk
101
cable trunking system
standard trunking
A return edge steel surface trunking system with strength and rigidity.
manufactured to BS 4678 Part1.
Four lid fixing options: Trunking Lengths - 3m
Plastic Turnbuckle, Die Cast
Turnbuckle, Screw Fix and Single Compartment
Tamperproof Screw Fix. 50 x 50 MG22N
Sizes up to 300 x 300 as standard, 75 x 50 MG32N
also available up to 650 wide to 75 x 75 MG33N
special order. 100 x 50 MG42N
100 x 75 MG43N
3 metre standard trunking lengths,
100 x 100 MG44N
other lengths available on request.
150 x 50 MG62N
Trunking lengths and fittings in 1, 2 150 x 75 MG63N
and 3 compartment options. 150 x 100 MG64N
Smooth return edges increase 150 x 150 MG66N
strength and rigidity.
LID FIXINGS
Standard Fixing:
Plastic turnbuckle
Alternative Fixings:
Die-cast turnbuckle
Screw fix
Tamperproof screw fix Turnbuckle Lid
Salamandre
MG_ _N
FINISHES
Standard Finish:
Pre-galvanized steel to BS EN 10142 & 3.
Alternative Finish:
Epoxy/polyester powder coated Standard
Grey /P to BS4800 00A05.
Other RAL colours available on request.
TRUNKING LENGTHS
Lid Fixing Finishes To complete the reference, add the trunking
Pre-galvanized Powder coated SIZE code given in the table (above).
Plastic turnbuckle MG SIZE N MG SIZE P EXAMPLE:
Die-cast turnbuckle MGD SIZE MGD SIZE P For 75x50 Single Compartment Powder
Screw fix MS SIZE MS SIZE P Coated Trunking, with Plastic Turnbuckle
Tamperproof screw fix MST SIZE MST SIZE P Fix Lid:- MG32P
102
cable trunking system
standard trunking
Screwfix Lid
MS_ _3C
Lids up to 150mm wide are supplied in 3.0m lengths. Single Compartment Spare Turnbuckle Lid
Lids 225 and 300mm wide are supplied in two Turnbuckles included.
Depth
1.5m lengths.
PLASTIC CASE TURNBUCKLES:
Lids up to 150 wide: 6 per 3m lid
Width Lids 225 and 300 wide: 4 per 1.5m lid
DIE CAST TURNBUCKLES:
Two Compartment Lids 50 wide: 3 per 3m lid
Lids 75 to 150 wide: 6 per 3m lid
Depth
Lids 225 and 300 wide: 4 per 1.5m lid
Width
For Ordering Information see page102. Trunking and fittings are supplied with equal For Ordering Information see page 102.
compartments as standard.
For Technical Information (Finishes, Cable For unequal compartments details must be For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights supplied at time of order. Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
103
cable trunking system
standard trunking
45° Bends
Top Lid 45° Bend Outside Lid 45° Bend
Single Compartment MG SIZE AL Single Compartment MG SIZE CL
Two Compartment MG SIZE AL2C Two Compartment MG SIZE CL2C
Three Compartment MG SIZE AL3C Three Compartment MG SIZE CL3C
Top Lid 45° Bend Inside Lid 45° Bend Outside Lid 45° Bend
35
C
35 35
Trunking
Depth A B C
50 50 75 100
75 60 90 110
100 70 95 115
150 85 105 130
Dimensions are identical for single and multi-compartment.
All dimensions in mm (nominal). All dimensions in mm (nominal).
104
cable trunking system
standard trunking
90° Bends
Top Lid 90° Bend - Gusset Inside Lid 90° Bend - Gusset Outside Lid 90° Bend - Gusset
Single Compartment MG SIZE AGL Single Compartment MG SIZE BGL Single Compartment MG SIZE CGL
Two Compartment MG SIZE AGL2C Two Compartment MG SIZE BGL2C Two Compartment MG SIZE CGL2C
Three Compartment MG SIZE AGL3C Three Compartment MG SIZE BGL3C Three Compartment MG SIZE CGL3C
Top Lid 90° Bend - Square Inside Lid 90° Bend - Square Outside Lid 90° Bend - Square
Single Compartment MG SIZE ASL Single Compartment MG SIZE BSL Single Compartment MG SIZE CSL
Two Compartment MG SIZE ASL2C Two Compartment MG SIZE BSL2C Two Compartment MG SIZE CSL2C
Three Compartment MG SIZE ASL3C Three Compartment MG SIZE BSL3C Three Compartment MG SIZE CSL3C
Top Lid 90° Bend - Gusset Inside Lid 90° Bend - Gusset Outside Lid 90° Bend - Gusset
MG_ _AGL 75 x 50 shown MG_ _BGL 75 x 50 shown MG_ _CGL 75 x 50 shown
MG_ _AGL2C not shown MG_ _BGL2C not shown MG_ _CGL2C not shown
MG_ _AGL3C not shown MG_ _BGL3C not shown MG_ _CGL3C not shown
Top Lid 90° Bend - Gusset Inside Lid 90° Bend - Gusset Outside Lid 90° Bend - Gusset
Width A/B C B A Up to 150 wide 225 & 300 wide C C Up to 150 wide 225 & 300 wide
B A
Depth A/B C Depth A/B C Depth A/B C Depth A/B C
50 75 25
75 100 25 50 75 25 50 86 35 50 75 25 50 86 36
100 125 25 75 100 25 75 111 35 75 100 25 75 111 36
150 175 25 100 125 25 100 136 35 100 125 25 100 136 36
225 261 36 150 175 25 150 186 35 150 175 25 150 186 36
300 336 36 225 261 35 A B 225 261 36
C C C C 300 336 35 300 336 36
Top Lid 90° Bend - Square Inside Lid 90° Bend - Square Outside Lid 90° Bend - Square
105
cable trunking system
standard trunking
Tees
Top Lid Tee - Gusset Inside Lid Tee - Gusset Off Set Tee
Single Compartment MG SIZE AGT Single Compartment MG SIZE BGT Two Compartment MG SIZE OST2C
Two Compartment MG SIZE AGT2C Two Compartment MG SIZE BGT2C Three Compartment MG SIZE OST3C
Three Compartment MG SIZE AGT3C Three Compartment MG SIZE BGT3C Not available for single compartment
Top Lid Tee - Square Outside Lid Tee - Gusset Information Sheets to enable customer
specification of Off Set Tees with unequal
Single Compartment MG SIZE AST Single Compartment MG SIZE CGT
compartments are available from our Sales
Two Compartment MG SIZE AST2C Two Compartment MG SIZE CGT2C Support.
Three Compartment MG SIZE AST3C Three Compartment MG SIZE CGT3C
All top lid, inside lid and outside lid tees
SIZE = Trunking Size, see table on page 102. are supplied with lid, lid fixings and tee
Component references are given for pre-galvanized EXAMPLE:
to trunking fastenings.
finish with plastic turnbuckle fix lid: References for For a 75x50 Two Compartment Powder Coated Top Offset tees are supplied with lids and lid
alternative finish and lid fixings are given on page 102. Lid Tee - Gusset with Screw Fix Lid:- MS32AGT2CP fixings only.
Top Lid Tee - Gusset Inside Lid Tee - Gusset Off Set Tee
MG_ _AGT 75 x 50 shown MG_ _BGT 75 x 50 shown MG_ _OST2C not shown
MG_ _AGT2C not shown MG_ _BGT2C not shown MG_ _OST3C 150 x 50 shown
MG_ _AGT3C not shown MG_ _BGT3C not shown
Salamandre
Top Lid Tee - Gusset Inside Lid Tee - Gusset Off Set Tee
Width A B A Up to 150 wide 225 & 300 wide
A Depth A B Depth A B A
50 100 25
75 125 25 50 100 25 50 122 35
100 150 25 75 125 25 75 147 35
150 200 25 100 150 25 100 172 35
225 297 36 150 200 25 150 222 35
300 372 36 225 297 35
B B 300 372 35
B B B
Top Lid Tee - Square Outside Lid Tee - Gusset Width A Depth B
Width A Up to 150 wide 225 & 300 wide 50 150 50 125
B B Depth A B Depth A B 75 175 75 160
50 120
A 75 145
100 200 100 196
50 100 25 50 122 36 150 250 150 266
100 170 75 125 25 75 147 36 225 325 225 370
150 220 100 150 25 100 172 36 300 400 300 478
225 325 150 200 25 150 222 36
300 400 225 297 36 Width and Depth refer to trunking sizes.
A 300 372 36 Dimensions are identical for single and multi-compartment.
35 All dimensions in mm (nominal).
106
cable trunking system
standard trunking
Tees Crossovers
Crossover
Single Compartment MG SIZE AGX SIZE = Trunking Size, see table on page 102.
Inside Lid Tee - Square and Outside
Lid Tee - Square are also available, Two Compartment MG SIZE AGX2C Component references are given for pre-galvanized
Three Compartment MG SIZE AGX3C finish with plastic turnbuckle fix lid: References for
contact our Sales Support for details.
alternative finish and lid fixings are given on page 102.
Off Set Crossover EXAMPLE:
Two Compartment MG SIZE OSX2C For a 75x50 Two Compartment Powder Coated
Crossover with Screw Fix Lid:- MS32AGX2CP
Three Compartment MG SIZE OSX3C
Not available for single compartment
Crossovers are supplied with lid, lid
Information Sheets to enable customer fixings and crossover to trunking
specification of Off Set Crossovers with fastenings.
unequal compartments are available from
our Sales Office. Offset crossovers are supplied with lids
and lid fixings only.
Crossover
MG_ _AGX 75 x 50 shown
MG_ _AGX2C not shown
MG_ _AGX3C not shown
B B A
B
A
A
B
B
A
B A A
Crossover
Width A/B
B A
A B 50 100
3 Compartment Top Lid Tee Fly-over 75 125
3 Compartment Crossover Fly-over
100 150
C 150 200 C B A
225 297 C
B 300 372
25 25 B
A Width A
Off Set Crossover A
C 50
75
150
175
A 100 200 C
B 150 250
225
300
325
400
B
A C B A Depth B A C B A
50 125
B 75 160
100 196
150 266
225 370 For Ordering Information see page 102.
300 478
Width and Depth refer to trunking sizes. For Technical Information (Finishes, Cable
Dimensions are identical for single and multi-compartment. Trunking Capacity, Lid Fixing, Coupling, Weights
All dimensions in mm (nominal). and Steel Gauges, ) see pages 120 and 121.
107
cable trunking system
standard trunking
For Ordering Information see page 102. For Ordering Information see page 102. For Ordering Information see page 102.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
108
cable trunking system
standard trunking
Supplied with lid and lid fixings. Only available in pre-galvanized finish.
SIZE = Trunking Size, see table on page 102. SIZE = Trunking Size, see table on page 102.
Component reference is given for pre-galvanized EXAMPLE:
finish with plastic turnbuckle fix lid: References for For a 75x50 Trunking Connector:- MG32C
alternative finish and lid fixings are given on page 102.
EXAMPLE:
For a 75x50 Powder Coated Fitting to Fitting Adaptor
with Screw Fix Lid:- MS32FAP
For Ordering Information see page 102. For Ordering Information see page 102.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
109
cable trunking system
standard trunking
Cable Retainer and Earth Link and Fastenings Stop End and Flange
Pin Rack
Cable Retainer (pack 10) Earth Link Stop End
50mm wide MG2CR pack 10 EL with fastenings MG SIZE E
75mm wide MG3CR
100mm wide MG4CR Fastenings Flange
150mm wide MG6CR Die Cast Turnbuckle pack 10 DTB with flange to trunking fastenings MG SIZE F
Retaining Clips, M5 pack 100 ETCLIP
Pin Rack Plastic Turnbuckle pack 10 PTB SIZE = Trunking Size, see table on page 102.
MG SIZE PR Component references are given for pre-galvanized
Lid/Connector Screws, M5 pack 100 T201
finish: Reference for alternative finish is given on
SIZE = Trunking Size, see table on page 102. Gasket, 10 x 1.5mm (10 metre roll) T202 page 102.
EXAMPLE: For a 75x50 Pin Rack:- MG32PR Lid/Connector Tamperproof Screws, M5 pack 100 T204 EXAMPLE:
Screwdriver for Tamperproof Screw TX25 For a 75x50 Powder Coated Stop End:- MG32EP
Plastic Turnbuckle
PTB
Salamandre
Flange
Retaining Clip MG_ _F
ETCLIP 75 x 50 shown
Pin Rack
MG_ _PR
Lid/Connector Screw
T201
Lid/Connector
Tamperproof Screw
T204
Pin Rack
up to 150 225 and 300
A A
Ø5 W
CLEARANCE
Trunking HOLES
Width W A
up to 150 W + 22.5 supplied in pairs
225 & 300 W + 26.0
All dimensions in mm (nominal).
For Ordering Information see page 102. For Ordering Information see page 102. For Ordering Information see page 102.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
110
cable trunking system
standard trunking
Pop rivet or spot weld on Use four retaining clips and screws per plate (not
site to suit. included), see page 110.
A
B 200
A M10 threaded rod
C B M10 nut
C Hanger
D Form A flat washer 200
D
All dimensions in mm (nominal). All dimensions in mm (nominal).
For Ordering Information see page 102. For Ordering Information see page 102. For Ordering Information see page 102.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
111
cable trunking system
stainless steel trunking
A return edge trunking system designed for corrosive and
exterior environments.
LID FIXINGS
Standard Fixing:
Screw fix
Alternative Fixing:
Tamperproof screw fix
Salamandre
ORDERING INFORMATION
COMPONENT REFERENCES
Component references are given for single References for lid fixings are given below.
compartment trunking and fittings with screw fix lid.
TRUNKING SIZE CODES TRUNKING LENGTHS MULTI COMPARTMENT TRUNKING
size in mm SIZE size in mm SIZE Lid Fixing References Compartments References
Wide x Deep CODE Wide x Deep CODE
Screw fix MS SIZE SS Two MS SIZE 2CSS
50 x 50 22 225 x 50 92
75 x 50 32 225 x 75 93 Tamperproof screw fix MST SIZE SS Three MS SIZE 3CSS
75 x 75 33 225 x 100 94 To complete the reference, add the trunking To complete the reference, add the trunking
100 x 50 42 225 x 150 96
SIZE code given in the table (left). SIZE code given in the table (far left).
100 x 75 43 225 x 225 99
100 x 100 44 300 x 50 122 EXAMPLE: EXAMPLE:
150 x 50 62 300 x 75 123 For 75x50 Single Compartment Stainless For 75x50 Two Compartment Stainless Steel
150 x 75 63 300 x 100 124 Steel Trunking, with Tamperproof Screw Trunking, with Screw Fix Lid:- MS322CSS
150 x 100 64 300 x 150 126 Fix Lid:- MST32SS
150 x 150 66 50 x 50 three compartment trunking and
fittings are not available.
The trunking SIZE code should be included in the
component reference where indicated. Trunking and fittings are supplied with equal
compartments as standard.
For unequal compartments details must be
supplied at time of order.
112
cable trunking system
stainless steel trunking
Depth
Width
113
cable trunking system
stainless steel trunking
SIZE = Trunking Size, see table on page 112. SIZE = Trunking Size, see table on page 112. SIZE = Trunking Size, see table on page 112.
Component references are given for single compartment Component references are given for single compartment Component references are given for single compartment
screw fix lid: References for multi-compartment and screw fix lid: References for multi-compartment and screw fix lid: References for multi-compartment and
alternative lid fixing are given on page 112. alternative lid fixing are given on page 112. alternative lid fixing are given on page 112.
EXAMPLE: For a 75x50 Two Compartment Top Lid EXAMPLE: For a 75x50 Two Compartment Top Lid EXAMPLE: For a 75x50 Two Compartment Crossover
90° Bend with Tamperproof Screw Fix Lid:- Tee with Tamperproof Screw Fix Lid:- with Tamperproof Screw Fix Lid:-
MST32AGLSS2C MST32AGTSS2C MST32AGXSS2C
All 90° bends are supplied with lid, lid All top lid, inside lid and outside lid tees All crossovers are supplied with lid, lid
fixings and bend to trunking fastenings. are supplied with lid, lid fixings and tee fixings and crossover to trunking
to trunking fastenings. fastenings.
All offset tees are supplied with lids and All offset crossovers are supplied with
lid fixings only. lids and lid fixings only.
For Ordering Information see page 112. For Ordering Information see page 112.
For Ordering Information see page 112. For Fly-over Information see page 107. For Fly-over Information see page 107.
For Dimensions see page 105. For Dimensions see page 106. For Dimensions see page 107.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
114
cable trunking system
stainless steel trunking
Change Face,
Left Hand
MS_ _CLHSS
50 x 50 shown
Flange
MS_ _FSS
75 x 50 shown
Change Face,
Right Hand Cable Retainer
MS_ _CRHSS MG_ _CRSS
50 x 50 shown 100mm wide shown
REDUCER SIZE CODES All bellmouths are supplied with lid, lid Connector supplied with connector
Main run size SIZE Main run size SIZE fixings and bellmouth to trunking screws.
in mm CODE in mm CODE fastenings. Stop End supplied with stop end to
Wide x Deep 1 2 Wide x Deep 1 2
All change faces are supplied with lids, trunking fastenings.
75 x 50 32SIZE 225 x 50 92SIZE
lid fixings and one trunking connector Flange supplied with flange to trunking
75 x 75 33SIZE 225 x 75 93SIZE
100 x 50 42SIZE 225 x 100 94SIZE fitted. fastenings.
100 x 75 43SIZE 225 x 150 96SIZE
100 x 100 44SIZE 225 x 225 99SIZE Cable Retainer supplied in packs of 10.
150 x 50 62SIZE 300 x 50 122SIZE
150 x 75 63SIZE 300 x 75 123SIZE
150 x 100 64SIZE 300 x 100 124SIZE
150 x 150 66SIZE 300 x 150 126SIZE
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
115
cable trunking system
IP rated trunking
A totally sealed system giving a degree of protection from
ingress of dirt and water and affording protection to a person
from potential enclosed hazards.
3 metre standard trunking lengths.
An environmental protection rating of IP54 is given when installed correctly.
Trunking lengths and fittings in 1,
It is possible to achieve a higher IP rating, but with a large steel enclosure like cable trunking
2 and 3 compartment options. the IP rating is completely dependant upon the installer.
Closed cell neoprene gaskets are
fitted between adjoining surfaces. IP Protection Classes
The protection of enclosures against ingress of dirt or against the ingress of water is defined in
LID FIXINGS IEC529 (BS EN 60529:1991). Conversely, an enclosure which protects equipment against
Standard Fixing: Screw fix ingress of particles will also protect a person from potential hazards within that enclosure, and
Alternative Fixing: Tamperproof screw fix this degree of protection is also defined as a standard.
The degrees of protection are most commonly expressed as "IP" followed by two numbers, e.g..
FINISHES IP65, where the numbers define the degree of protection. The first digit shows the extent to
Standard Finish: Pre-galvanized steel which the equipment is protected against particles, or to which persons are protected from
Alternative Finishes: Powder coated grey enclosed hazards. The second digit indicates the extent of protection against water. The wording
Stainless Steel in the table is not exactly as used in the standards document, but the dimensions are accurate.
ORDERING INFORMATION
COMPONENT REFERENCES
Component references are given for pre-galvanized References for finishes and lid fixings are
single compartment trunking and fittings with screw given below.
fix lid.
TRUNKING LENGTHS MULTI COMPARTMENT TRUNKING
TRUNKING SIZE CODES Lid Fixing Finishes Compartments References
size in mm SIZE size in mm SIZE Pre-galvanized Two WS SIZE 2C
Wide x Deep CODE Wide x Deep CODE Screw fix WS SIZE Three WS SIZE 3C
50 x 50 22 150 x 100 64 Tamperproof screw fix WST SIZE
75 x 50 32 150 x 150 66 Powder coated
To complete the reference, add the trunking
75 x 75 33 225 x 50 92 SIZE code given in the table (far left).
100 x 50 42 225 x 75 93 Screw fix WS SIZE P
100 x 75 43 225 x 100 94 Tamperproof screw fix WST SIZE P EXAMPLE:
100 x 100 44 225 x 150 96 For 75x50 Two Compartment Stainless Steel
Stainless steel
150 x 50 62 225 x 225 99 IP Rated Trunking, with Screw Fix Lid:-
Screw fix WS SIZE SS
150 x 75 63 WS322CSS
Tamperproof screw fix WST SIZE SS
The trunking SIZE code should be included in the 50 x 50 three compartment trunking and
To complete the reference, add the trunking fittings are not available.
component reference where indicated.
SIZE code given in the table (left).
EXAMPLE: Trunking and fittings are supplied with equal
For 75x50 Single Compartment Powder compartments as standard.
Coated Trunking, with Tamperproof Screw For unequal compartments details must be
Fix Lid:- WST32P supplied at time of order.
116
cable trunking system
IP rated trunking
Trunking Lengths
3
Depth 5 4
4
Connector
Width 5 Closed cell
Connector clamp neoprene gaskets
117
cable trunking system
IP rated trunking
SIZE = Trunking Size, see table on page 116. SIZE = Trunking Size, see table on page 116. SIZE = Trunking Size, see table on page 116.
Component references are given for pre-galvanized Component references are given for pre-galvanized Component references are given for pre-galvanized
single compartment screw fix lid: References for multi- single compartment screw fix lid: References for multi- single compartment screw fix lid: References for multi-
compartment and alternative finishes and lid fixing are compartment and alternative finishes and lid fixing are compartment and alternative finishes and lid fixing are
given on page 116. given on page 116. given on page 116.
EXAMPLE: For a 75x50 Two Compartment Powder EXAMPLE: For a 75x50 Two Compartment Powder EXAMPLE: For a 75x50 Two Compartment Powder
Coated Top Lid 45° Bend with Tamperproof Screw Coated Top Lid 90° Bend - Gusset with Tamperproof Coated Top Lid Tee - Gusset with Tamperproof Screw
Fix Lid:- WST32ALP2C Screw Fix Lid:- WST32AGLP2C Fix Lid:- WST32AGTP2C
All 45° bends are supplied with lid, lid All 90° bends are supplied with lid, lid All tees are supplied with lid(s), lid
fixings and one connector set. fixings and one connector set. fixings and two connector sets.
Top Lid 90° Bend Top Lid 90° Bend Top Lid Tee Top Lid Tee
Top Lid 45° Bend Gusset Square Gusset Square
A A
WS_ _AL 75 x 75 shown A A B B
55 115
55 F 60
60
Inside Lid Tee Inside Lid Tee
Inside Lid 90° Bend Inside Lid 90° Bend Gusset Square
Inside Lid 45° Bend
Salamandre
Gusset Square B B
WS_ _BL 75 x 75 shown C C D D
55 G 55 115
60 60
Outside Lid Tee Outside Lid Tee
Outside Lid 90° Bend Outside Lid 90° Bend
Outside Lid 45° Bend Gusset Square
Gusset Square
WS_ _CL 75 x 75 shown 60 55
60 115
55 F
C C E E B B
All shown
All shown as 75 x 75 as 75 x 75
Size A B C D E F G Size A B
Top Lid
Wide x Deep Wide x Deep
45° Bend
50 x 50 165 165 165 165 165 115 115 50 x 50 280 280
75 x 50 190 190 165 165 165 115 115 75 x 50 305 280
75 x 75 190 190 190 190 190 115 115 75 x 75 305 305
100 x 50 215 215 165 165 165 115 115 100 x 50 330 280
100 x 75 215 215 190 190 190 115 115 100 x 75 330 305
111 Inside Lid 100 x 100 215 215 215 215 215 115 115 100 x 100 330 330
45° Bend 150 x 50 265 265 165 165 165 115 115 150 x 50 380 280
150 x 75 265 265 190 190 190 115 115 150 x 75 380 305
Outside Lid
150 x 100 265 265 215 215 215 115 115 150 x 100 380 330
45° Bend
150 x 150 265 265 265 265 265 115 115 150 x 150 380 380
111
225 x 50 340 375 165 168 170 120 115 225 x 50 455 280
225 x 75 340 375 190 193 195 120 115 225 x 75 455 305
111 225 x 100 340 375 215 218 220 120 115 225 x 100 455 330
225 x 150 340 375 265 268 270 120 115 225 x 150 455 380
225 x 225 340 375 340 343 345 120 115 225 x 225 455 455
Dimensions are identical for single and multi-compartment. Dimensions are identical for single and multi-compartment. Dimensions are identical for single and multi-compartment.
All dimensions in mm (nominal). All dimensions in mm (nominal). All dimensions in mm (nominal).
For Ordering Information see page 116. For Ordering Information see page 116. For Ordering Information see page 116.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
118
cable trunking system
IP rated trunking
SIZE = Trunking Size, see table on page 116. SIZES = Trunking Sizes, see table below. SIZE = Trunking Size, see table on page 116.
Component reference is given for pre-galvanized Component reference is given for pre-galvanized Component references are given for pre-galvanized
single compartment screw fix lid: References for multi- screw fix lid: References for alternative finishes and lid screw fix lid: References for alternative finishes and lid
compartment and alternative finishes and lid fixing are fixing are given on page 116. fixing are given on page 116.
given on page 116. EXAMPLE: For a Powder Coated Reducer with EXAMPLE: For a 75x50 Powder Coated Connector
EXAMPLE: For a 75x50 Two Compartment Powder Tamperproof Screw Fix Lid, reducing from 150x150 Set with Tamperproof Screw Fix Lid:- WST32CP
Coated Crossover with Tamperproof Screw Fix Lid:- to 75x75:- WST6633RP EXAMPLE: For a 75x50 Powder Coated Stop End
WST32AGXP2C with Tamperproof Screw Fix Lid:- WST32EP
All crossovers are supplied with lid, lid All reducers are supplied with lid, lid All connector sets are supplied with
fixings and three connector sets. fixings, one connector set (for reduced Connector, lid, lid fixings, clamps and
run) and fastenings. connector to trunking fastenings.
All stop ends are supplied with lids, lid
fixings, clamps and connector to
trunking fastenings.
For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable For Technical Information (Finishes, Cable
Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights Trunking Capacity, Lid Fixing, Coupling, Weights
and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121. and Steel Gauges, ) see pages 120 and 121.
119
cable trunking system
technical information
150 101 75 38
For each size of cable multiply the number to be 100 63
Press turnbuckle into lid 150 114
installed by its own common factor. Add together All dimensions 225 72
the results of these calculations for all cable sizes. and installation is in mm (nominal). 300 110
The correct trunking size must have a factor equal complete.
to or greater than this total.
Hole Positions for Lids
Example:
24 x 16.0mm2 stranded @50 = 1200 Simply turn 90° Cut to Length
20 x 2.5mm2 solid @ 10.2 = 204 clockwise to lock (or anti-
PLASTIC CASE TURNBUCKLE Ø 14.1mm holes
clockwise to release),
1404 50mm wide 75 to 150 wide 225 and
using a No.2 cross head 115 150 300 wide
screwdriver. B 150
∴ Trunking size = 75x50 (capacity factor 1555) B
B
A
Cable Sizes Size mm2 (nom.) Factor A
and Factors Screw Fixing 35
SOLID 1.5 7.1 A
2.5 10.2 Screws are M5 x 6mm (M5 x 10mm for IP Rated
STRANDED 1.5 8.1 Trunking) posidrive, pan head with earth nib on
Trunking
2.5 11.4 underside of head and a rounded end to prevent Width A B
4.0 15.0 cable damage. 50 18 17.50
6.0 22.0 75 43 18.00
10.0 38.0 Manufactured to BS4183 and BS3643 from low 100 68 18.00
16.0 50.0 carbon mild steel, zinc plated and clear passivated. 150 118 17.75
225 193 18.25
25.0 75.0
35.0 95.0 Tamperproof Screw Fixing 300 268 18.75
50.0 133.0 An M5 x 12mm pan head screw with the efficient DIE-CAST CASE TURNBUCKLE Ø 9.5mm holes
70.0 177.0 high torque TORX® recess. 50mm wide 75 to 150 wide 225 and
95.0 227.0 150 150 300 wide
120.0 284.0 Tamperproof screw fix lids are supplied fitted with 150
B B
150.0 346.0 mild steel plated screws with TORX® screws B
240.0 552.0 bagged separately for fitting when installation is
complete. A
Trunking Sizes Size mm Factor A
• Torque transmitted positively and accurately.
and Capacity 50x50 1037
Factors 75x50 1555 • Large contact area - reduces wear.
Trunking
75x75 2371 Width A B
100x50 2091
• Parallel sides - holds driver captive and
50 — 26.5
100x75 3189 virtually eliminates slippage and camout. 75 45.5 16.7
100x100 4252 Manufactured to BS4183 and BS3643 from low 100 70.5 16.7
150x50 3091 150 120.5 16.5
carbon mild steel, zinc plated and clear passivated. 225 195.5 17.0
150x75 4742
300 270.5 17.5
150x100 6394 A special TORX® screwdriver is needed.
150x150 9697
SCREW FIXED
225x50 4646
225x75 7114 Ø 7.2mm holes must be drilled at the cut end for
M5 screws.
225x100 9298 50 to 300 wide
This table is based on a 225x150 14652 Trunking 150
theoretical calculation 225x225 21766 Width A B
B
and must be taken only 300x50 6182 Drive surfaces 50 40 6.50
300x75 9486 parallel with axis 75 65 7.25
as a guide, due regard Large contact
100 90 7.25
300x100 12788 area, no stress of screw reduces A
must be taken of future 150 140 7.50
300x150 19447 concentrations disengagement risk
wiring needs. 225 215 5.00
300x225 28900 or stress raisers 300 290 5.00
300x300 38000
All dimensions in mm (nominal).
120
cable trunking system
technical information
150 x 150
225 x 150
225 x 225
100 x 100
150 x 100
225 x 100
300 x 100
300 x 150
300 x 225
300 x 300
150 x 50
150 x 75
225 x 50
225 x 75
100 x 50
100 x 75
300 x 50
300 x 75
50 x 50
75 x 50
75 x 75
weight in kg
Bend
0.3 0.4 0.5 0.5 0.6 0.7 0.9 0.9 1.1 1.3 1.6 1.7 2.0 2.4 3.0 2.5 2.7 3.0 3.5 3.7 3.9
Tee
0.3 0.4 0.5 0.6 0.7 0.7 0.9 1.0 1.1 1.3 1.6 1.7 1.9 2.2 2.7 2.5 2.6 2.9 3.2 3.4 3.6
Reducer
– 0.5 0.5 0.5 0.7 0.8 0.8 0.9 1.0 1.1 1.3 1.4 1.5 1.6 1.9 1.6 1.7 1.8 1.9 2.2 2.8
Bellmouth
0.5 0.8 0.8 1.2 1.3 1.4 1.6 1.7 1.8 1.9 2.1 2.2 2.3 2.4 2.9 2.6 2.7 2.8 2.9 3.4 3.9
Change Face
0.6 0.8 1.0 1.0 1.1 1.3 1.3 1.4 1.5 2.3 1.7 1.8 2.4 2.8 3.3 2.1 2.7 2.9 3.2 3.7 4.3
Steel Gauges
All trunking gauges are to BS4678 and are for
Pre-Galvanized finish only.
150 x 150
225 x 150
225 x 225
100 x 100
150 x 100
225 x 100
300 x 100
300 x 150
300 x 225
300 x 300
150 x 50
150 x 75
225 x 50
225 x 75
100 x 50
100 x 75
300 x 50
300 x 75
50 x 50
75 x 50
75 x 75
Thickness in mm
Trunking
Lengths 1.0 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.4 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6*
Trunking
Lids 1.0 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.6 1.6 1.4 1.4 1.4 1.6 1.6 1.6 1.6 1.6 1.6*
121
LIGHTING TRUNKING
LET US
LIGHTEN
YOUR
WORKLOAD
Salamandre
of hassle.
122
LIGHTING TRUNKING
The range is
supported by a
complete selection
of labour-saving
fittings that
guarantees the
perfect solution
every time
www.legrand.co.uk
123
lighting trunking system
trunking body
A 'Clip-in' lid trunking system for fast installation.
Trunking Body
Trunking Body
50x50
Available in two standard sections: LT1_
50x50mm and 50x25mm.
1.2mm and 1.0mm gauges are Trunking Body
50x25
available.
LT5_
Salamandre
ORDERING INFORMATION
The information below applies throughout the
Lighting Trunking range, unless otherwise stated.
Component References
Trunking Body References are obtained by
giving the type, followed by the size, length and
gauge (see table below).
EXAMPLE 1:
For 50x50 Pre-galvanized Trunking Body, 4 metre
long, 1.0mm gauge:- LT1/410
Standard 1.2mm gauge Straight Length to
Use for larger spans when minimum deflection Fitting Joint
Type Size Length Gauge
is required. Tighten the M5 screws
(pressing the fitting against
50 x 50
50 x 25
Lighting
1.2mm
White
body) to secure.
Light 1.0mm gauge
W LT 1 5 3 4 5 6 10 12 Use for shorter spans or where the trunking is
concealed e.g. a cavity ceiling.
For white plastic coated finish add prefix W to the
reference. LT1
FINISHES
Standard Finish: 50
Additional Finish:
Powder Coated (epoxy/polyester) white For Trunking Deflection and Weights, see page 129.
124
lighting trunking system
trunking fittings
Long Coupler
LT_C
250
Long Coupler
Straight
Tighten Length
the M5 screws to
Long Coupler
(pressing the couplerJoint
against the top flange of
Tighten the M5 screws
the trunking body) to (pressing the
coupler against the top flange of
secure.
the trunking body) to secure.
For Ordering Information, see page 124. For Ordering Information, see page 124.
For Trunking Deflection and Weights, see page 129. For Trunking Deflection and Weights, see page 129.
125
lighting trunking system
trunking fittings
Fixing lids at a Top Lid 90° Bend junction Fixing lids at a Fourway junctions
Attach fitting cover, see page 127, then fit lids into Attach fitting cover, see page 127, then fit lids into
trunking and slide under fitting cover. trunking and slide under fitting cover.
Overlapping lids will fit flush with the fitting cover. Overlapping lids will fit flush with the fitting cover.
Top Lid 90° Bend Cover, see page 127. Fourway Cover, see page 127.
For Straight Length to Fitting joint, see page 124. For Straight Length to Fitting joint, see page 124.
For Ordering Information, see page 124. For Ordering Information, see page 124.
For Trunking Deflection and Weights, see page 129. For Trunking Deflection and Weights, see page 129.
126
lighting trunking system
trunking fittings
Top Lid Tee Outside Lid Tee Top Lid 90° Bend Cover
_AST 50 x 50 shown _CST 50 x 50 shown LT1ASL/LID
Fourway Cover
LT1ASX/LID
Fixing lids at a Top Lid Tee junctions The Fitting Cover will simply 'click' into place after
Attach fitting cover, see alongside, then fit lids into the fitting to trunking joint has been made.
trunking and slide under fitting cover.
Overlapping lids will fit flush with the fitting cover.
For Ordering Information, see page 124. For Ordering Information, see page 124.
For Trunking Deflection and Weights, see page 129. For Trunking Deflection and Weights, see page 129.
127
lighting trunking system
ancillary items
Ancillary Items
End Cap Girder Clamp Suspension Unit
50 x 50 LT1E 50 x 50 LT1GC Pack 10 LT1FS
50 x 25 LT5E 50 x 25 LT5GC
White 50 x 50 WLT1E White 50 x 50 WLT1GC
White 50 x 25 WLT5E White 50 x 25 WLT5GC Pull Switch Adaptor
Pack 10 LT1PSA
Flange Stirrup Hanger
50 x 50 LT1F 10mm hole 50 x 50 LT1H/10
50 x 25 LT5F 20mm hole 50 x 50 LT1H/20 Socket Box
White 50 x 50 WLT1F White 10mm hole 50 x 50 WLT1H/10 13amp standard LT1SB
White 50 x 25 WLT5F White 20mm hole 50 x 50 WLT1H/20 13amp non standard LT1NS
Supplied complete with socket.
LT_H/20 LT1SB
shown shown
Trunking
Flange
End Cap
69
Ø6
CLEARANCE
HOLES
For Ordering Information, see page 124. Finishes, see page 124.
128
lighting trunking system
technical information
Klik Adaptor
Pack 10 LT1KL
Load
Cable Retainer (kgs)
LT1CR
3 Metre Span
Weights
Non-standard 13amp Plug
CO104 (single pole) The weights given are in kilograms (nominal) and
CO105 (double pole) subject to material thickness tolerance.
Fourway
LT1ASX each 0.6
Tee
LT1AST each 0.5
End Cap
LT1E each 0.2
Flange
LT1F each 0.2
129
DATA TRUNKING
THOUGHTFUL
DESIGN
Salamandre
trunking encompasses a
130
DATA TRUNKING
www.legrand.co.uk
131
data trunking system
trunking lengths and fittings
Finish
Grey enamel.
132
data trunking system
fittings and ancillary items
Fitting Coupler
CR22 Bridge Piece
BP3
Four Way
NFT33 Fire Barriers
FB33
133