Beruflich Dokumente
Kultur Dokumente
Thousands of TITAN push-pull props have proven themselves over many years.
They have the following advantages:
Ø
mm
48
TITAN RSK
Ø
mm
48
Ø
mm Ø
70 mm Ø TITAN RS
83 mm
8
10
80 Ø
6x mm
w1 57
scre
TITAN RS and TITAN RSK
200
140
≈15º
repositioning by crane
0
0–
31
00
approx. 1400
±5
0 (5
(4.6’)
.6
Rd 48 x 1/4”
’–
10
left
.2‘
)
14
Ø70 x 2,8
’)
adjustment
900-1500 mm
(3 – 4.9 ft), size 1
Rd 48 x 1/4”
86
approx. 400
right
3(
2.8
(1.3’)
3’)
≈ 820 – 430 (1
1400 ± 50 580 (1 .4’)
(2.7 –
4.6’) .9’)
old new
GENERAL RULES
1) The length of the brace (push-pull prop) should of rotation should be installed at the same side (e.g. all left
be identical to the height of the element handed threads at the ground). In this way, all props can be
lengthened or shortened by rotating in the same direction
2) Each element must be supported by a minimum
of two braces In order to see the difference between left
handed and right handed screw jacks:
3) If the swivel end is connected to the element at a single
point, the brace should be at an angle of less than 45° to Left handed thread is black polyseal-coated,
avoid additional offset forces
Right handed thread is hot-dip galvanized.
4) If several TITAN RSK props are used (e.g. along a wallform),
it is recommended that all threads with the same direction
TITAN RS and TITAN RSK
Proven anchorage to fix TITAN push-pull Fixing to the ground
props in detail
17,5 17 50
–5 +5 150
140
8
Swivel end
with fixing at 2 positions Double end
with 2 heavy duty dowels M 16 (5/8”). The for fixing two TITAN braces, ideal to push
hole 27 mm dia. (1.06”) has the function of a formwork exactly into position.
slotted hole to
eliminate a tolerance of ± 5 mm
(± 0,2”) when positioning the dowel. TITAN recoverable anchor screw M24 / D15
x 160 with TITAN 15
Swivel end with fixing at 1 position tie bar with hex. nut SW 30 x 50, fits to ring
is used when the brace is positioned inclined Fixing of prefabricated panels
spanner 30, perm. load 30 kN in concrete
in two directions to the Cast-in sleeve type “Robusta” 25 Ø x 200
strength B15
element that has to be supported. (1”Ø x 8”) with special bolt 25 Ø x 150 mm
(15 N/mm2).
By rotating around the fixing (1”Ø x 6”) permissible load 10 kN (2250
Always sufficient for single point fixing.
position and simultaneous rotation around the lbs) in concrete strength B 30 (4200 psi) out
axis of the brace the of the design only one point fixing possible,
swivel end can be easily brought this reduces the perm. load of the TITAN
into the required position to facilitate brace to 14 kN (3100 lbs) on compression.
erection of the element.
wedge ends
L
height of element is identical to supporting length of braces
TITAN RSK 3
extension 1800-3200 mm
(5.9’ to 10.5’)
wedge
Spanner
500 mm (1,65’), suitable for TITAN RSK For various types of formwork with
push pull props double U-channel having sufficient
space to adapt the 48 mm Ø (1.9”)
screw jacks of type TITAN RSK
48
50
TITAN RS and TITAN RSK
rail post
waler
1,25 m (4’)
U-channel
1,25 m (4’)
to be cut on site
Aluminium Prop TITAN Size 6 + 1 m (3.3’) extension + jack 1,20 m (3.9’)
retaining claw
connecting bracket
lifting eye
4x4-timber to be
cut on site
wallform
TITAN M hinge
plate
combi
plate 15
retaining claw
F70
washer
faced nut
ledger frame
TITAN trolley
scaffold
Aluminium Prop TITAN Size 4
boards
TITAN BKS
The TITAN BKS heavy duty push-pull props have the following advantages:
• Proven load capacities
• Flexible lengths up to 18 m (60 ft) with interchangeable modular sections
• Sturdy construction withstands abusive handling on site
• Fine adjustment up to 1.40 m (55 inch) with screw jacks top and bottom
• Adjustment of screw jacks always within arm's length for maximum safety
• Fast adjustment with double-start speed thread, 25 mm (1 inch) per turn
Aluminium Push-Pull Prop TITAN BKS-Alu
slotted hole 18 x 38 for tolerances
Endplate
for fixing with 4 dowels M 16 required, bore
hole depth 120 mm (4.7”), concrete strength
180
180 (7.1”)
120 (4,7”)
optional: perm. load 2 x 25 kN (5600 lbs)
B 25 (25 N/mm2), perm. load
35
with screws type ROBUSTA 30 Ø
10 kN (2300 lbs) per dowel
Remarks:
4 screws M 16 x 60, strength 10.9,
180 (7.1”)
galvanised are required to connect
260 (10,2”) prop elements. They are included
330 (13.0”) in the price.
Technical Data
Type adjustment perm. axial load screw extension weight
range on compression jack short long
min half max element
L L L L pcs. pcs. pcs.
m kN kN kN kg
ft lbs lbs lbs lbs
BKS 1 2,3 - 3,7 50,0 50,0 50,0 2 - - 72
7.5‘ to12.1‘ 11200 11200 11200 159
BKS 2 4,7 - 6,1 50,0 50,0 41,5 2 1 - 122
15.4‘ to 20.0‘ 11200 11200 9300 269
BKS 3 6,0 - 7,4 50,0 50,0 37,4 2 - 1 144
19.7‘ to 24.3‘ 11200 11200 8400 317
BKS 4 7,1 - 8,5 50,0 45,3 32,6 2 2 - 172
23.3‘ to 27.9‘ 11200 10200 7300 379
BKS 5 8,4 - 9,8 50,0 39,1 28,2 2 1 1 194
27.6‘ to 32.2‘ 112040 8800 6300 427
BKS 6 9,7 - 11,1 45,7 33,2 23,8 2 - 2 216
31.8‘ to 36.4‘ 10300 7500 5400 476
BKS 7 10,8 - 12,2 39,0 28,3 20,1 2 2 1 244
35.4‘ to 40.0‘ 8800 6400 4500 538
BKS 8 12,1 - 13,5 32,5 23,8 16,7 2 1 2 266
39.7‘ to 44.3‘ 7300 5400 3800 586
BKS 9 13,2 - 14,6 25,1 19,9 13,7 2 3 1 294
43.3‘ to 47.9‘ 5600 4500 3100 648
BKS 10 14,5 - 15,9 19,3 15,9 11,2 2 2 2 316
47.6‘ to 52.2‘ 4300 3600 2500 697
BKS 11 15,8 - 17,2 14,6 11,9 9,1 2 1 3 338
51.8‘ to 56.4‘ 3300 2700 2000 745
BKS 12 17,1 - 18,5 10,8 8,7 6,8 2 - 4 360 50 kN (11200 lbs) permissible load
56.1’ to 60.7’ 2400 2000 1500 794 on tension
Subject to technical changes Imperial figures are rounded.
Components:
screw jack element adjustment 1,15 – 1,85 m (3.77 to 6.1 ft) 36 kg ( 79 lbs)
short extension, 159 mm Ø (6,26”) x 4,5 mm (1,8”) x 2,40 m (7,87 ft) 50 kg (110 lbs)
long extension, 159 mm Ø (6,26”) x 4,5 mm (1,8”) x 3,70 m (12.15 ft) 72 kg (159 lbs)
2
short extension 2,40 m (7.9’)
3
long extension 3,70 m (12.1’)
4
2 short extension 2,40 m (7.9’)
screw jack element screw jack element
Aluminium Push-Pull Prop TITAN BKS-Alu
TITAN BKS-ALU is a modular system consisting of BKS-Alu- Technical Data Permissible axial load kN (lbs)
spindle element, TITAN ALU-extension element and ALU-
type / size 6 7 8
connecting brackets.
adjustment m 4,12 - 6,56 5,12 - 7,56 6,12 - 8,5
ft 13.52 to 21.52 16.80 to 24.80 20.08 to 28.08
One person can assemble different sizes of TITAN BKS-ALU perm. load min L kN 36,0 23,8 16,0
on compression lbs 8100 5400 3600
Push-Pull Prop quickly and easily without using a crane.
perm. load half L kN 20,4 13,8 9,2
• For bracing and adjusting prefabricated on compression lbs 4600 3100 2100
concrete elements perm. load max L kN 10,4 7,3 4,9
• For bracing and aligning wall and column on compression lbs 2300 1600 1100
formwork perm. load kN 40 40 40
on tension lbs 9000 9000 9000
• Long-lasting rental system
weight kg (lbs) 43 (95) 51 (112) 59 (130)
• Modular system for different lengths and Alu-spindle element 2 2 2
perm. loads
Alu-extension 1 m – 1 2
• Proven load capacities Alu-connection bracket 2 4 6
weight and wind acc. to DIN 4420 have been included in the static calculation.
45 (10100)
40 (9000)
35 (7900)
perm. load on compression kN (lbs)
30 (6700)
25 (5600)
20 (4500)
15 (3400)
10 (2200)
5 (1100)
adjustment (m)
type 6 without extension
type 7 with extension 1 m (3,3’)
type 8 with 2 x extension 1 m (3,3’)
load assumption in static calculation:
45° inclination with self-weight, without wind
perm. load on tension 40 kN (9000 lbs)
Aluminium Push-Pull Prop TITAN BKS-Alu
TITAN-ALU extension element Connecting bracket Swivel end with pin handle
length weight Two connecting brackets, one on each Fast and self-locking bolt for push-pull
TITAN BKS-Alu-spindle element 500 mm (1’ 7”) 3.5 kg ( 7.7 lbs) side, secure the connection between the prop with swivel end to reduce time for
without swivel end, adjustment 2.06 to 1000 mm (3’ 3”) 6.5 kg (14.3 lbs) TITAN-BKS-ALU spindle element and assembly and crane
3.28 m (6.8 to 10.7 ft), approx. 21 kg (47 5000 mm (16’ 5”) 24.0 kg (52.9 lbs) the TITAN-ALU extension element or
lbs), a spanner is required to ease adjust- between 2 extension elements.
ment under full load.
Safe working load zul. N (pressure) per strut (N1; N2)
N1
Aluminium push pull props TITAN BKS
with ledger frames
Load chart – static calculation dd. 15.07.2005
N1
Alu-push-pull prop
TITAN BKS-ALU
ledger frame
push-pull prop
TITAN RSK
Ischebeck Titan Group
Product Availability
Technical Support
HEAD OFFICE
John Dean House
Wellington Road
Burton upon Trent
Staffordshire DE14 2TG
Tel: 01283 515677 Fax: 01283 516126
www.ischebeck-titan.co.uk
E-mail: sales@ischebeck-titan.co.uk
NORTHERN REGIONAL OFFICE Since our policy is one of continuous improvement we reserve the right to
change without prior notice the specifications and methods of construction
& DESIGN OFFICE mentioned in this document. No responsibility whatsoever can be accepted for
any errors or omissions in, or misinterpretation of the contents. Products must
Hollinwood Business Centre be used in conformity with safe practices and applicable codes and
Albert Mills Albert Street regulations. Photos and details shown are for general guidance only and may
vary according to circumstances. For specific information refer to Ischebeck
Hollinwood Oldham OL8 3QP Titan Limited. Copyright reserved.