Beruflich Dokumente
Kultur Dokumente
Select one:
a. the pressure of reservoir at the end of the pipe
b. relative compressibility of liquid to expansion
c. time for a pressure to traverse the pipe
d. rate of deceleration of flow
Feedback
The correct answer is: time for a pressure to traverse the pipe
Question 2
Not answered
Marked out of 1.00
Flag question
Question text
Fluids that are pumped in processing work are frequently more viscous than water. Which of
the following statements is corrects?
Select one:
a. Reynolds number varies directly as the viscosity
b. Efficiency of a pump increases as the viscosity increases
c. Increased fluid friction between the pump parts and the passing fluid increases useful
work
d. Working head increases as the viscosity increases.
Feedback
The correct answer is: Increased fluid friction between the pump parts and the passing fluid
increases useful work
Question 3
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. air
b. natural gas
c. water
d. steam
Feedback
The correct answer is: air
Question 4
Not answered
Marked out of 1.00
Flag question
Question text
Medium pressure when applied to valves and fittings, implies they are suitable for a working
pressure of from:
Select one:
a. 862 to 1200 kPa
b. 500 to 1000 kPa
c. 685 to 1050kPa
d. 758 to 1000 kPa
Feedback
Question 5
Not answered
Marked out of 1.00
Flag question
Question text
In a hydro-electric plant using a Francis turbine with medium head, the speed can be
regulated by using the:
Select one:
a. deflector gate
b. wicket gate
c. weir
d. nozzle
Feedback
Question 6
Not answered
Marked out of 1.00
Flag question
Question text
At any instant, the number of particles passing every cross-section of the stream is the
same, the flow is said to be:
Select one:
a. turbulent flow
b. continuous flow
c. steady flow
d. uniform flow
Feedback
Question 7
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. inward flow impulse
b. inward flow reaction
c. outward flow reaction
d. outward flow impulse
Feedback
Question 8
Not answered
Marked out of 1.00
Flag question
Question text
The power required to deliver a given quantity of fluid against a given head with no losses
in the pump is called:
Select one:
a. wheel power
b. hydraulic power
c. brake power
d. indicated power
Feedback
The correct answer is: hydraulic power
Question 9
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. height above a chosen datum, density, internal energy, pressure and velocity of/low
b. velocity of flow only
c. pressure, height above a chosen datum, velocity of flow, density of fluid
d. pressure only
Feedback
The correct answer is: height above a chosen datum, density, internal energy, pressure and
velocity of/low
Question 10
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. hydrograph
b. topograph
c. hectograph
d. monograph
Feedback
Question 11
Not answered
Marked out of 1.00
Flag question
Question text
What is a check valve?
Select one:
a. a valve designed to release the excess pressure
b. a valve which allows flow of fluid in either direction
c. a valve used for checking the pressure of fluid
d. a valve design to allow a fluid to pass through in one direction only
Feedback
The correct answer is: a valve design to allow a fluid to pass through in one direction only
Question 12
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. energy balance
b. mass balance
c. heat balance
d. diameter balance
Feedback
Question 13
Not answered
Marked out of 1.00
Flag question
Question text
In a pipe specification, schedule is used, when the pipe specified as " schedule 80", the pipe
corresponds to the
Select one:
a. internal pressure
b. "extra standard" weight
c. extra strong
d. "old standard" weight
Feedback
Flag question
Question text
Select one:
a. hydraulic gradient
b. hydraulic radius
c. hydraulic lead
d. hydraulic energy
Feedback
Question 15
Not answered
Marked out of 1.00
Flag question
Question text
What is the value of the Mach no. at the throat of a converging- diverging nozzle?
Select one:
a. zero
b. One
c. Two
d. Ten
Feedback
Question 16
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. spiral casing
b. penstock
c. tailrace
d. surge tame
Feedback
Question 17
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. a restriction in flow area occurs
b. the specified mass flow rate cannot occur
c. a valve is closed in a line
d. shock waves always occur
Feedback
The correct answer is: the specified mass flow rate cannot occur
Question 18
Not answered
Marked out of 1.00
Flag question
Question text
The property of liquid in which they extend resistance to angular or shear deformation is
Select one:
a. Density
b. Specific gravity
c. viscosity
d. Specific weight
Feedback
Question 19
Not answered
Marked out of 1.00
Flag question
Question text
Which of the following is a reason for the head loss in long pipeline?
Select one:
a. friction
b. velocity
c. pressure
d. elevation
Feedback
Question 20
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. a welded built-up tee
b. a pipe tee the branch of which is larger than the run
c. a pipe tee with head shaped like a bull
d. a pipe tee with its run larger than its branch
Feedback
The correct answer is: a pipe tee the branch of which is larger than the run
Question 21
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. foam type
b. flow nozzle
c. pilot tube
d. venturi tube
Feedback
Question 22
Not answered
Marked out of 1.00
Flag question
Question text
In the processing section, there is an instrument frequently used to measure the flow rate of
fluids. What is the instrument consisting of a vertical passage with variable cross-sectional
area, a float and calibrated scale?
Select one:
a. manometer
b. rota-aire
c. rotameter
d. pitot-tube
Feedback
Question 23
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Reynolds number
b. Mach number
c. Froude number
d. Average number
Feedback
Question 24
Not answered
Marked out of 1.00
Flag question
Question text
If the fluid travels parallel to the adjacent layers and the paths of individual particles do not
cross, the flow is said to be:
Select one:
a. dynamic
b. turbulent
c. laminar
d. critical
Feedback
Question 25
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. RL=1/2MV2
b. RL = 2MV2
c. RL = 1/2 MV
d. RL=RLN-m
Feedback
Question 26
Not answered
Marked out of 1.00
Flag question
Question text
The liquid pressure in the surface per area in the surface at the bottom is:
Select one:
a. adhesion pressure
b. cohesion pressure
c. magnitude pressure
d. intensity pressure
Feedback
Question 27
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. uniform flow
b. steady flow
c. discharge
d. continuous flow
Feedback
Question 28
Not answered
Marked out of 1.00
Flag question
Question text
Is an abrupt reduction in flow velocity due to sudden increase of water depth in the down
stream direction
Select one:
a. Hydraulic gradient
b. Hydraulic energy
c. Hydraulic jump
d. Weirs
Feedback
Question 29
Not answered
Marked out of 1.00
Flag question
Question text
The locus of elevation to which water will rise in the piezometer tube is termed:
Select one:
a. friction head
b. hydraulic gradient
c. critical path
d. energy gradient
Feedback
Question 30
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. it is used to connect two pipes by welding
b. it connects two pipes with the use of threaded couplings
c. it is used to connect two pipes by pressing both ends
d. when tightened, compress tapered, sleeves so that they form a tight joint on the
periphery of the tubings they connect
Feedback
The correct answer is: when tightened, compress tapered, sleeves so that they form a tight
joint on the periphery of the tubings they connect
Question 31
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. inside diameter
b. pipe wall thickness
c. outside diameter
d. approximate size
Feedback
Question 32
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Pelton
b. Banki
c. Parson
d. Hero
Feedback
Question 33
Not answered
Marked out of 1.00
Flag question
Question text
An engineer found that the fluid flowing in the pipe is low. What diameter of pipe should be
recommended?
Select one:
a. reduce the diameter
b. no diameter
c. increase the diameter
d. constant diameter
Feedback
Question 34
Not answered
Marked out of 1.00
Flag question
Question text
The total energy in a compressible or incompressible fluid flowing across any section in a
pipeline is a function of:
Select one:
a. pressure and velocity
b. pressure, density, velocity and viscosity
c. flow energy, kinetic energy, height above datum and internal energy
d. pressure, density and velocity
Feedback
The correct answer is: flow energy, kinetic energy, height above datum and internal energy
Question 35
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. The smoothness of the surface
b. Compression joints
c. Bell and spigot joint
d. The dimensional standard to which each is manufactured
Feedback
The correct answer is: The dimensional standard to which each is manufactured
Question 36
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. aneroid barometer
b. anemoscope
c. anemograph
d. anemometer
Feedback
Question 37
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. a pipe bent to a loop to change direction
b. a large radius bend in pipe line to absorb longitudinal expansion in the pipe line due to
heat
c. a double loop radius elbow to minimize friction losses
d. a pipe expander fitting
Feedback
The correct answer is: a large radius bend in pipe line to absorb longitudinal expansion in
the pipe line due to heat
Question 38
Not answered
Marked out of 1.00
Flag question
Question text
What is the result when the fluid's kinetic energy during a stagnation process is transformed
to enthalpy?
Select one:
a. rise in the temperature and pressure of fluid
b. rise in fluids volume
c. decrease in fluid's volume
d. Decrease in the temperature and pressure of fluid13.
Feedback
The correct answer is: rise in the temperature and pressure of fluid
Question 39
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. friction factor of a pipe
b. velocity of flow in a closed conduit
c. length of pipe in a closed network
d. quantity of discharge through an orifice
Feedback
Question 40
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. spillway
b. tailrace
c. dam
d. none of these
Feedback
The measure of the fluid resistance when acted upon by an external force is called:
Select one:
a. density
b. tackiness
c. viscosity
d. flashpoint
Feedback
Question 2
Not answered
Marked out of 1.00
Flag question
Question text
In order to avoid vaporization in the pipeline, the pipeline over the ridge is laid in such a
way that it is not more than:
Select one:
a. 5.0 m above the hydraulic gradient
b. 10.0 m above the hydraulic gradient
c. 2.4 m above the hydraulic gradient
d. 6.4 m above the hydraulic gradient
Feedback
Question 3
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. NR3/2
b. NR
c. NR1/2
d. NR1/4
Feedback
Question 4
Not answered
Marked out of 1.00
Flag question
Question text
In a flow of fluids through channel wherein the velocity changes along the length of a
channel from point to point on the account of changing its depth, width and direction of
flow is:
Select one:
a. uniform flow
b. non uniform flow
c. constant flow
d. unsteady flow
Feedback
Question 5
Not answered
Marked out of 1.00
Flag question
Question text
A fluid flows at a constant velocity in a pipe. The fluid completely fills the pipe, and the
Reynolds number is such that the flow is just subcritical and laminar. If all other parameters
remain unchanged and the viscosity of the fluid is decreased a significant amount, one
would generally expect the flow to:
Select one:
a. increase
b. not change
c. become more laminar
d. become turbulent
Feedback
Question 6
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. 10 times poise
b. 9.81 times poise
c. 1/9.81 times poise
d. 1/10 times poise
Feedback
Flag question
Question text
The line of action of the bouyant force always acts through the centroid of the:
Select one:
a. Displaced volume of the fluid
b. Volume of the fluid vertically above the body
c. Volume of the floating body
d. Submerged body
Feedback
Question 8
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. turbulent flow
b. inadequate compaction
c. surface tension
d. low fluid pressure
Feedback
Question 9
Not answered
Marked out of 1.00
Flag question
Question text
The velocity of a fluid particle at the centre of the pipe section is:
Select one:
a. Average
b. Minimum
c. Logarithmic average
d. Maximum
Feedback
Question 10
Not answered
Marked out of 1.00
Flag question
Question text
If the actual kinetic energy of a nozzle is Ka and Ki in the max. value that can be attained by
an isentropic expansion from initial to final state, then efficiency of a nozzle is
Select one:
a. Ka/Ki
b. Ki=Ka
c. KaxKi
d. Ki/Ka
Feedback
Question 11
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Mercury
b. semi-solid
c. acidic fluids
d. Newtonian fluid
Feedback
Question 12
Not answered
Marked out of 1.00
Flag question
Question text
Nozzles does not involved any work interaction. The fluid through this device experiences.
Select one:
a. no change in enthalpy
b. no change in potential energy
c. no change in kinetic energy
d. vacuum
Feedback
Question 13
Not answered
Marked out of 1.00
Flag question
Question text
Neglecting the forces due to inertia, gravity and frictional resistance, the design of a channel
can be made by comparing:
Select one:
a. Froude's number
b. Plandtl number
c. Reynolds number
d. Weber number
Feedback
Question 14
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. can never be found if frictionless fluid regardless of its motion
b. depend upon cohesive forces
c. may occur owing to cohesion when the fluid is at rest.
d. can never be found when the fluid is at rest
Feedback
The correct answer is: may occur owing to cohesion when the fluid is at rest.
Question 15
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. One of the physical properties of the fluid
b. Dependent upon the flow and density
c. The viscosity divided by the density
d. A function of temperature and pressure of fluid.
Feedback
The correct answer is: Dependent upon the flow and density
Question 16
Not answered
Marked out of 1.00
Flag question
Question text
For pipes extending more than 1000 times the diameter what are the major losses of
hydraulic head due to ?
Select one:
a. pressure
b. friction
c. velocity
d. cross-sectional change
Feedback
Question 17
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. above the centre of gravity
b. below the centre of bouyancy
c. above the centre of bouyancy
d. below the centre gravity
Feedback
Question 18
Not answered
Marked out of 1.00
Flag question
Question text
A steady flow device used to increase pressure by slowing down the fluid.
Select one:
a. nozzle
b. generator
c. diffuser
d. turbine
Feedback
Question 19
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. viscous unviscous fluids
b. compressibility of fluids
c. conservation of mass
d. steady unsteady flow
Feedback
Question 20
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. suction valve
b. exhaust pipe
c. manifold
d. discharge valve
Feedback
Question 21
Not answered
Marked out of 1.00
Flag question
Question text
A leak from a faucet comes out in separate drops. Which of the following is the main cause
of this phenomenon?
Select one:
a. viscosity of fluid
b. air resistance
c. surface tension
d. gravity
Feedback
Question 22
Not answered
Marked out of 1.00
Flag question
Question text
For supersonic and subsonic divergent nozzle, what is the Mach number for supersonic:
Select one:
a. greater than 1
b. less than 1
c. 1
d. 0
Feedback
Question 23
Not answered
Marked out of 1.00
Flag question
Question text
The convergent section of a nozzle increases the velocity of the flow gas. What does it do in
its pressure?
Select one:
a. decrease the pressure
b. pressure becomes constant
c. pressure is equal to velocity
d. increase the pressure
Feedback
Question 24
Not answered
Marked out of 1.00
Flag question
Question text
Flow of fluids wherein its particles do not have definite paths and the paths of the individual
and distinct particles cross one another is
Select one:
a. laminar flow
b. unsteady flow
c. non-uniform flow
d. turbulent flow
Feedback
Question 25
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Has uniformly varying dynamic pressure
b. Exists in case of rotational flow
c. Has no velocity component tangent to it.
d. Has no velocity component normal to it
Feedback
Question 26
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Dynamic viscosity/Kinematic viscosity
b. Kinematic viscosity x dynamic viscosity
c. None of the above.
d. Kinematic viscosity/ Dynamic viscosity
Feedback
Question 27
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. unsteady
b. constant
c. uniform
d. equal
Feedback
Question 28
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. a and b above are correct
b. It provides a suitable meniscus for the inclined tube
c. cheap and easily available
d. Its density being less can provide longer length for a pressure difference, thus more
accuracy can be obtained.
Feedback
Question 29
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. The change in transverse direction is zero
b. Rate of change of velocity opt fluid is zero
c. At every point the velocity vector is identical in magnitude and direction for any given
instant
d. Conditions remain unchanged with time at any point
Feedback
The correct answer is: At every point the velocity vector is identical in magnitude and
direction for any given instant
Question 30
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. all of the above
b. The velocity is uniform over the cross-sections
c. The flow is one dimensional
d. The flow is steady
Feedback
Question 31
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. unity
b. near unity
c. less than unity
d. greater than unity
Feedback
Question 32
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. above the centroid
b. At the centroid
c. Below the centroid
d. At metacentre
Feedback
Question 33
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. VD5/m
b. VDρ/m
c. 2VD/u
d. VDm/8
Feedback
Question 34
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. pressure
b. temperature
c. volume
d. thickness
Feedback
Question 35
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. States that the energy remains constant along stream line
b. States that energy is constant everywhere in the fluid
c. Applies to irrotational flow only
d. States that the net rate of in-flow into any small volume must be zero
Feedback
The correct answer is: States that energy is constant everywhere in the fluid
Question 36
Not answered
Marked out of 1.00
Flag question
Question text
The rise or fall of head "h" in a capillary tube of diameter "d" and liquid surface tension "s"
and specific weight "w" is given by:
Select one:
a. 4s/wd
b. 4ds/w
c. 4wd/s
d. 4ws/d
Feedback
Question 37
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. 1 in
b. 1/2 in
c. 2 1/2 in
d. 3/8 in
Feedback
Question 38
Not answered
Marked out of 1.00
Flag question
Question text
Which of the following is the basis of Bernoulli's law for fluid flow?
Select one:
a. Fourier's law
b. The principle of conservation of energy
c. The principle of conservation of mass
d. The continuity equation
Feedback
Question 39
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. The difference between two velocities.
b. The average between the higher velocity and average velocity.
c. Average velocity
d. Vector difference of two velocities.
Feedback
Question 40
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. 75.0 cm of Hg
b. 31.0 ft water
c. 33 inch Hg
d. 1.013 kg kcm2
Feedback
Select one:
a. 9xx
b. 40xx
c. 72xx
d. 92xx
Feedback
Question 2
Not answered
Marked out of 1.00
Flag question
Question text
The flux that should be provided in soldering electrical connection or commutator wires as it
tends to corrode the connections.
Select one:
a. Sal ammoniac
b. Stearin
c. Acid fluxes
d. Zinc chloride
Feedback
Question 3
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. crucible furnace
b. tempering furnace
c. induction furnace
d. cupola furnace
Feedback
Question 4
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Mercury
b. Steel
c. Chromium
d. Aluminum
Feedback
Question 5
Not answered
Marked out of 1.00
Flag question
Question text
Non - metallic material of high melting temperature being used as furnace lining.
Select one:
a. dolomite clay bricks
b. refractories
c. quartz bricks
d. silica sand
Feedback
Question 6
Not answered
Marked out of 1.00
Flag question
Question text
Stress relieving is also _______ for the purpose of reducing the internal stress of steel material
/ metal.
Select one:
a. tempering
b. normalizing
c. quenching
d. drawing
Feedback
Question 7
Not answered
Marked out of 1.00
Flag question
Question text
The property that characterizes a materials ability to be drawn into a wire is known as
Select one:
a. elasticity
b. plasticity
c. utility
d. ductility
Feedback
Question 8
Not answered
Marked out of 1.00
Flag question
Question text
Continuous stretching under load even if the stress is less than the yields point is known as
Select one:
a. creep
b. elasticity
c. ductility
d. plasticity
Feedback
Question 9
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Galvanic
b. Spitting
c. Erosion
d. Crevice
Feedback
Question 10
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. SAE 43xx
b. SAE 41xx
c. SAE 5xxx
d. SAE 6xxx
Feedback
Question 11
Not answered
Marked out of 1.00
Flag question
Question text
It refers to any layer or deposit of extraneous material on the heat - transfer surface.
Select one:
a. Pressure drop
b. Fouling
c. Low line
d. Scaling
Feedback
Question 12
Not answered
Marked out of 1.00
Flag question
Question text
A carbon content in the range of _____ in steel readily responds to heat treatment.
Select one:
a. 0.28 to 0.30 % C
b. 0.35 to 0.40 % C
c. 0.18 to 0.25 % C
d. 0.12 to 0.15 % C
Feedback
Question 13
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. aluminum
b. zinc
c. mercury
d. lead
Feedback
Question 14
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. High carbon
b. Low carbon
c. Tool and die
d. High speed steel
Feedback
Question 15
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Lead
b. Zinc
c. Manganese
d. Copper
Feedback
Question 16
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. SAE 13xx
b. SAE74xx
c. SAE 43xx
d. SAE 10xx
Feedback
Question 17
Not answered
Marked out of 1.00
Flag question
Question text
What is the property of a material, which resists forces acting to pull the material apart?
Select one:
a. Shear strength
b. Tensile strength
c. Torsional strength
d. Compressive strength
Feedback
Question 18
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. they are on the left side of the periodic table
b. they have extra electrons as exhibited by normally possible balance state
c. having characteristics luster
d. the electrons are loosely bound to the nuclei and therefore mobile
Feedback
The correct answer is: the electrons are loosely bound to the nuclei and therefore mobile
Question 19
Not answered
Marked out of 1.00
Flag question
Question text
It is hardening treatment whereby a cast metal is being heated to a very high temperature
then suddenly subjected to rapid cooling to improve hardenability of wear resistance is
called
Select one:
a. tempering
b. normalizing
c. annealing
d. quenching
Feedback
Question 20
Not answered
Marked out of 1.00
Flag question
Question text
The gradual chemical reaction by other substance such that the metal is converted to an
oxide or other compounds.
Select one:
a. Corrosion
b. Rusting
c. Cheeping
d. Weathering
Feedback
Question 21
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. kiln dried wood
b. core portion of wood
c. sap wood
d. heart wood
Feedback
Question 22
Not answered
Marked out of 1.00
Flag question
Question text
Treatment process that produces a residual compressive stress at the surface and residual
tension on the inside that results in considerable increase in fatigue strength for members
on torsion / bending is known as
Select one:
a. quenching
b. heavy oil quenching
c. shallow quenching
d. partial quenching
Feedback
Question 23
Not answered
Marked out of 1.00
Flag question
Question text
A metal, which has a high electrical conductivity but should not be used for high
temperature.
Select one:
a. Silicon
b. Chrome alloy
c. Zinc
d. Carbide
Feedback
Question 24
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Normalizing furnace
b. Annealing furnace
c. Tempering furnace
d. Induction furnace
Feedback
Question 25
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. 45xx
b. 48xx
c. 47xx
d. 46xx
Feedback
Question 26
Not answered
Marked out of 1.00
Flag question
Question text
The smallest area at the point of rupture of a tensile specimen divided by the original area is
called
Select one:
a. percentage reduction of the area
b. Izod test
c. Charpy test
d. percentage elongation
Feedback
Question 27
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. 1
b. 2 to 5
c. 1 to 3
d. 2 to 8
Feedback
Question 28
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. SAE
b. ASTM
c. AISI
d. SEA
Feedback
Question 29
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Aluminum
b. All of the above
c. Silicon
d. Manganese
Feedback
Question 30
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Zinc
b. Lead
c. Antimony
d. Babbitt
Feedback
Question 31
Not answered
Marked out of 1.00
Flag question
Question text
Used as cast condition steel casting with carbon content less than ____ % C.
Select one:
a. 0.26
b. 0.15 to 0.18
c. 0.20
d. 0.25
Feedback
Question 32
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. alloyed steel
b. alloyed bronze
c. cast iron
d. alloyed aluminum
Feedback
Question 33
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. SAE 2xxx
b. SAE 3xxx
c. SAE5xxx
d. SAE4xxx
Feedback
Question 34
Not answered
Marked out of 1.00
Flag question
Question text
Alloy steel known for its resistance to corrosion, abrasion and wear that is usually ideal for
mill grinding of ore in cement and concentrator application. It is usually combined with
molybdenum to increase the depth hardening.
Select one:
a. Chromium - nickel - moly steel
b. Chromium - moly steel
c. Manganese chromium steel
d. Manganese - moly steel
Feedback
Question 35
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. High manganese casting
b. Manganese - nickel steel casting
c. High chrome steel casting
d. Chrome - nickel steel casting
Feedback
Question 36
Not answered
Marked out of 1.00
Flag question
Question text
The application of electrical current to the corrosion circuit to counter the corrosion reaction
is called
Select one:
a. cathodic protection
b. galvanic action
c. sacrificial anodes method
d. chemical corrosion process
Feedback
Question 37
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. Columbium
b. All of the above
c. Titanium
d. Tantalum
Feedback
Question 38
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. bituminous coke
b. graphite electrodes
c. foundry coke
d. anthracite coke
Feedback
Question 39
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. All of the above
b. Toughness
c. Plasticity
d. Stiffness
Feedback
Question 40
Not answered
Marked out of 1.00
Flag question
Question text
Select one:
a. ductility
b. plasticity
c. malleability
d. elasticity
Feedback