Beruflich Dokumente
Kultur Dokumente
all ce need
Step-by-step for CEREC® all yo
u
1
Preparation
CAD/CAM process
Try-in
Observe the preparation guide- As a preparation for intra-oral CAD/CAM process Smooth out the attachment Try in the restoration in its blue
lines and minimum thicknesses for imaging, cover the preparation Mill the restoration from points and finish the restoration. state. Check and adjust the
preparation with IPS Contrast Spray IPS e.max CAD Observe the minimum occlusion/articulation, if required.
2
Chairside thickness and contact points.
Preparation for
combination firing*
(Crystallization and Glaze)
Fill the restoration with IPS Object Adapt IPS Object Fix Putty to Remove any contamination Apply individual characterizations Spray an even and covering layer
Fix Putty and press the IPS e.max the pin and crown margin. Avoid from the outer surface of the using IPS e.max CAD Crystall./ of IPS e.max CAD Crystall./
CAD Crystallization Pin into the contamination of the outer side of crown using a brush dampened in Shades and Stains. Glaze Spray onto the restoration.
3
Putty material. the restoration. water.
Combination firing
Cleaning
Try-in
Place the restoration in the Conduct the combination firing After cooling, remove the Clean the restoration with ultra- After crystallization, try in the
center of the IPS e.max CAD based on the number of restorations restoration from the auxiliary sound in a water bath. restoration.
Crystallization Tray. and the type of glazing using the firing paste.
Programat CS2.
4
Preparation for
cementation
Placement
Before final placement, etch the Allow Monobond® Plus to react Clean the preparation, rinse with Apply Multilink® Automix to the IPS e.max CAD restoration in situ.
restoration for 20 seconds using for 60 seconds and dry with air. water and blow dry with air. Apply internal surface of the restoration.
IPS Ceramic Etching Gel. Multilink® Automix Primer A/B,
scrub it in for 30 seconds and
disperse excess with blown air.
* IPS e.max CAD Crystall./Glaze Paste may optionally be used to glaze the restoration. For the fabrication of inlays and onlays, observe the Instructions for Use of IPS e.max chairside!
CEREC® is a registered trademark of Sirona Dental Systems GmbH
ramic
all ce need
ou
0.6 0.6 1.0 1.0 1.0
all y
1.0 1.0 1.0 1.0 6° 1.0 6°
1.0 6° 1.0 6° 6° 6° 6°
1.0 1.5 1.0 1.5 1.5 1.0
1.5 1.5 1.5 1.5
1.5
1.0 1.0 1.0
1.5 1.5 1.5 1.5
1.0
100-120° 100-120° 100-120° 1.5 1.5 1.5 1.5 1.5 1.
1.0 1.0
1.0 1.0 1.0 1.
1.0 6° 1.0 6° 6° 6° 6°
1.0 1.0 6°
1.0 1.0
1.0 1.0
Inlay 100-120°
Onlay
100-120° Partial crown Posterior crown
Programat® CS2
The Programat CS2 is the ideal ceramic and crystallization furnace for dentists.
It has been especially developed for the crystallization of IPS e.max CAD
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.5 1.5 1.5 1.5 restorations. 1.5
1.5 1.5 1.5 1.5 1.51.5 1.5
Among other features, the Programat CS2 is equipped with pre-installed
1.0 1.0
1.0 1.0 1.0 1.0
IPS e.max CAD programs,1.0 which are used depending on the working technique
1.5 1.51.5 1.5
6° 1.5 1.5
and
6° glaze material 6°
1.5 (spray or
1.5 paste). Also, individual programs can be saved.
1.5 1.5 1.5 1.5
1.0 1.0
1.0 1.0 1.0 1.0
Cementation 6° IPS e.max
6° CAD (lithium disilicate glass-ceramic)
self-adhesive*/
Cementation method adhesive adhesive
conventional
Etching 20 sec. with IPS® Ceramic Etching Gel 20 sec. with IPS® Ceramic Etching Gel
1) For self-adhesive cementation, the restorations must be silanized. * self-adhesive powder/liquid systems
See Instructions
627931/en/2015-04-13