Beruflich Dokumente
Kultur Dokumente
EVM II
EVM Energía del Valle de México II
Combined Cycle Power Plant
Owner Contractor
GE POWER
Gas Power Systems
Revision
Revision A 2018-02-21
Date
KKS
EVM II
ECS NETWORK TOPOLOGY
Legend
MDH Network
PDH Network
UDH Network
EDH Network
Profibus Segments GE CLASS II ( INTERNAL NON-CRITICAL )
Irig-B Segments
g
UNLESS OTHERWISE SPECIFIED SIGNATURES DATE GENERAL ELECTRIC COMPANY
Typical Control Scope (See 4108) DIMENSIONS ARE IN INCHES
DRAWN
A. BENOIT 2018-02-20 GE Energy Products
TOLERANCES ON CHECKED
2 PL DECIMALS ± S. HOGG SEE PLM
3 PL DECIMALS ± ENGRG 2018-02-20
C
ANGLES ±
FRACTIONS ± ISSUED ECS Network Topology
COPYRIGHT 2018 GENERAL ELECTRIC COMPANY SEE PLM SEE PLM
FIRST MADE FOR: IPS 1154163
THIRD ANGLE PROJECTION MLI/COST CODE: 4110
APPLIED CAGE CODE DWG NO
PRACTICES
DISTR
B 127T3686
TO
SHEET
GENERAL ELECTRIC COMPANY. SIM TO SCALE RDO CODE : 1 of 23
DT-1N
SIZE DWG. NO. SH. REV.
B 127T3686 2 A
SUMMARY
SHEET NO DESCRIPTION REVISION
2 SUMMARY A
3 ECS NOTES - SH1 -
4 ECS NOTES - SH2 -
5 CONTROL SYSTEM NETWORK OVERVIEW A
6 ENGINEERING/CONTROL ROOM OVERVIEW A
7 MAIN eROOM OVERVIEW A
8 ROP eROOM OVERVIEW A
9 MAIN eROOM - GT11 / ST ECS AND EDGE PANEL TYPICALS A
10 MAIN eROOM - GT12 ECS TYPICALS A
11 ROP eROOM EDGE PANEL TYPICAL A
12 ELECTRICAL MV/LV MOTOR STARTER TYPICALS -
13 ELECTRICAL MV/LV BREAKERS DISTRIBUTION TYPICALS -
14 ELECTRICAL MV/LV DIESEL DISTRIBUTION TYPICAL -
15 EDH TOPOLOGY OVERVIEW A
16 ECS GPGs REDUNDANCY & PDH CONNECTION -
17 ECS GPGs & GPP/TPP TO MASTER CLOCK CONNECTION -
18 MAIN eROOM GT11 MSD IEDs CONNECTIONS TO ECS PANEL SWITCHES A
19 MAIN eROOM GT12 MSD IEDs CONNECTIONS TO ECS PANEL SWITCHES A
20 MAIN eROOM ST MSD IEDs CONNECTIONS TO EDGE PANEL SWITCHES -
21 MAIN eROOM MSD IEDs CONNECTIONS TO BHC12 SWITCHBOARD SWITCHES A
22 MAIN eROOM MSD IEDs CONNECTIONS TO BMC10 SWITCHBOARD SWITCHES -
23 ACRONYMS -
AREA HIGHLIGHTED IN GREY SHOWS TYPICAL CONTROL TEAM SCOPE (DETAILED IN MLI 4108)
Notes here after are given to provide a general overview of the ECS system.
A Vendor ECS dedicated network topology that will detail the owner, type, connections, IP addresses of all the IEDs, switches, concentrator panel
will be provided later during project requisition and will be used for commissioning and maintenance.
Refer to the ECS fact sheet or ECS Manual for further information about ECS system
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
127T3686
DISTR
SUMMARY DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 2 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 3 -
DISTR
ECS NOTES - SH1 DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 3 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 4 -
Typical protocols and redundancies: ECS connection to PDH needs 2x copper Cat-6 F/UTP redundant ports to GT Mark VIe PDH switches (Multimode fiber
possible in option) with following blocked IP addresses.
f) Master hot Concentrator to PDH switch 1: 172.16.203.248,
g) Master hot Concentrator to PDH switch 2: 172.16.203.250,
h) Master stand-by Concentrator to PDH switch 1: 172.16.203.249,
i) Master stand-by Concentrator to PDH switch 2: 172.16.203.251.
Time synchronization:
j) Each ECS concentrators needs one multimode fiber (Irig-b RG58 coaxial single ports depending to the distance to
plant s time server is available as an option).
k) GPGs and main protection IEDs (G60, T60 of GPP) use Irig-B time synchronization as master (more accurate)
and NTP (via Ethernet) as back-Up.
There are 3 types of communication between ECS and DCS which need to be opened and available when using a firewall.
The following table provides the TCP ports using for these communication links.
(1) Depends on the existing capability of the devices: IEC61850 preferred for source time stamp, fail-over redundancy
preferred when operator initiated remote control required, goose messaging preferred in case the device needs to share
information with other IEDs (e.g. Automatic Transfer Scheme) to avoid using conventional hard-wiring between these
IEDs.
(2) Motor starter are controlled by Mark Vie through Profibus DP, therefore the ECS advance monitoring is via single comm .
IEDs to EDH switches are cat-6 F/UTP or multimode Fiber (as per requirements) with following blocked IP address ranges:
a) EDH switches: 172.16.150.001 to 099,
b) Plant Common IEDs: 172.16.150.100 to 255,
c) Block 1 IEDs (GT/ST/HRSG/BOP): 172.16.151.001 to 255,
d) Block 2 IEDs (GT/ST/HRSG/BOP): 172.16.152.001 to 255,
e) Block X IEDs (GT/ST/HRSG/BOP): 172.16.15x.001 to 255.
ECS Concentrator does not have any I/Os nor logic, it communicates through protocol to the different IEDs that have I/Os and
logic.
DISTR
ECS NOTES - SH2 DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 4 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 5 A
HV SWITCHYARD
Cyber Security
MDH A
MDH B
PDH A
PDH B
MarkVIe
HMIs Gateways Historian EX2100 LS2100 GPGs
Controllers
UDH A
UDH B
EDH
IED and ML / or or or or (Each it s own IEDs and Switches as per project DOR)
DISTR
CONTROL SYSTEM NETWORK OVERVIEW DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 5 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 6 A
A10
Note:
ECS does not have any additional hardware in Central Control Room (CCR).
ECS does not have any additional hardware in Engineering room nor ECS Admin KVM. Refer to ECS Note 5.c).
ECS uses same DCS hardware for alarm management, historian, OPC gateways. Refer to ECS Note 6.a) b) c).
ECS viewer software is installed on the same EWS, CRM / OWS. Refer to ECS Note 6.d).
ECS GPGs and main protection panel IEDs are synchronized to same NTP time server. Refer to sheet 16.
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
127T3686
DISTR
ENGINEERING/CONTROL ROOM OVERVIEW DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 6 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 7 A
MAIN eROOM
PDH A
PDH B
ECS_ADM ECS_ADM
GPGx C650x GPGx
19" Rack 19" Rack
MONITOR MONITOR
GPGx C650x GPGx
ECS BAY ECS
GT11 CONCENTRATOR ST CONTROLLER GT12 CONCENTRATOR
GPP GPP GPP
EDH
A10
Note:
GPP/TPP relays connections moved from UDH to EDH.
One ECS panel per GT located next to GT GPP / GT Mark VIe. Refer to ECS Note 2.
Mark Vie controllers and/or Remote IOs have profibus DP connections to the different MV/LV Switchboards and MCCs Motor Starter IEDs.
MV/LV Switchboards and MCCs IEDs have Ethernet connection to EDH network for advance monitoring and breaker control. Refer to ECS Note 4.
- - - (Dotted red line) Represent fail-over redundancy when Goose or Operator initiated remote control required. Refer to ECS Note 4.
DISTR
MAIN eROOM OVERVIEW DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 7 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 8 A
A8
ROP E-ROOM
A3
C650x
C650x
BAY
CONTROLLER
EDH
A10
Note:
Plant Utility Owner provides Edge Panel as required (with EDH pair of switches).
Mark Vie controllers and/or Remote IOs have profibus DP connections to the different MV/LV Switchboards and MCCs Motor Starter IEDs.
MV/LV Switchboards and MCCs IEDs have Ethernet connection to EDH network for advance monitoring and breaker control. Refer to ECS Note 4.
- - - (Dotted red line) Represent fail-over redundancy when Goose or Operator initiated remote control required. Refer to ECS Note 4.
DISTR
ROP eROOM OVERVIEW DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 8 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 9 A
ML3000 ML3000
EDH Ring
GPG Concentrators
C650
ML3000 ML3000
ECS_ADM
19" Rack
MONITOR IDM
Internal Diagnostic Module
Miscellaneous
Common related non-smart
signals digitalization
GT11 GPP/TPP GT11 IO Module IEDs GT11 Other IEDs ST GPP/TPP DC/UPS Swbd, charger, inv. ST/BOP IO Module IEDs ST/BOP Other IEDs
C650
A5 Diesel Generator A5
IO module IO module
A9
GSUT / UAT A9
GSUT
Monitoring System Monitoring System
Located in Electrical Bay controller Located in Electrical
Compartments for busbar metering Compartments
(e.g. LCIC, GSEC, LEC) Other GT11 and other non-smart (e.g. LCIC, GSEC, LEC) Other ST/BOP
or Equipment JBs Electrical IEDs signal digitalization or Equipment JBs Electrical IEDs
for local non-smart signal for local non-smart signal
digitalization These are some examples digitalization These are some examples
Note:
One ECS concentrator panel is provided along with GT11, and one Edge panel for ST/BOP and located juxtaposed inside eRoom.
Edge panel is provided without administrator HMI.
ECS Concentrator panel switches connects all the GT11 GPP/TPP and other GT11 related miscellaneous IEDs.
Edge panel switches connects all the ST GPP/TPP, DC/UPS and other ST/BOP related miscellaneous IEDs.
The IEDs are connected with Modbus TCP or IEC61850, single or fail-over redundant ports as required. Refer to ECS Note 4.
- - - (Dotted red line) Represent fail-over redundancy when Goose or Operator initiated remote control required. Refer to ECS Note 4.
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
MAIN eROOM – GT11 /ST ECS AND EDGE PANEL TYPICALS 127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 9 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 10 A
ML3000
EDH Ring
GPG Concentrators
ML3000
ECS_ADM
19" Rack
MONITOR IDM
Internal Diagnostic Module
A5 Diesel Generator
IO module
Energy Meters A4
G60s / T60s
A9
GSUT / UAT
Monitoring System
Located in Electrical
Compartments
(e.g. LCIC, GSEC, LEC) Other GT12
or Equipment JBs Electrical IEDs
for local non-smart signal
digitalization These are some examples
Note:
One ECS concentrator panel is provided along with GT12.
ECS Concentrator panel switches connects all the GT12 GPP/TPP and other GT12 related miscellaneous IEDs.
The IEDs are connected with Modbus TCP or IEC61850, single or fail-over redundant ports as required. Refer to ECS Note 4.
- - - (Dotted red line) Represent fail-over redundancy when Goose or Operator initiated remote control required. Refer to ECS Note 4.
DISTR
DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 10 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 11 A
A8
ROP eROOM- EDGE PANEL
ML3000
EDH Ring
C650
ML3000
A10
Miscellaneous
Common related non-smart
signals digitalization
Other DC/UPS Swbd, charger, inv. Other IO Module IEDs Other IEDs
C650
IO module
Battery charger(s)
/ UPS inverter(s)
Note:
Other Edge panel(s) use to be added when a significant quantity of non-smart signals remain to be digitalized for plant common and/or other block related area(s) far from eRoom.
Additional Edge panel(s) are defined / supplied by the team that own these non-smart signals (GE / Customer / Partner teams).
The IEDs are connected with Modbus TCP or IEC61850, single or fail-over redundant ports as required. Refer to ECS Note 4.
- - - (Dotted red line) Represent fail-over redundancy when Goose or Operator initiated remote control required. Refer to ECS Note 4.
A8
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
127T3686
DISTR
ROP eROOM - EDGE PANEL TYPICAL DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 11 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 12 -
ML3000 ML3000
EDH Ring
ML3000 ML3000
Bay controller Incomer / Coupler Large Transformer Bay controller Large Bay controller
for busbar metering / Feeder Incomer / Feeder for busbar metering Incomer / Coupler for busbar metering
and other non-smart (differential protection) and other non-smart (also include ATS) and other non-smart
signal digitalization signal, feeder digitalization signal, inomer, feeder
digitalization
(also include ATS)
Note:
ECS have IEC61850 for breaker control and advance monitoring (include oscillo file auto retrieve).
Refer to ECS Note 4.
DISTR
ELECTRICAL MV/LV BREAKERS DISTRIBUTION TYPICAL DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 12 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 13 -
Marck Vie
PDP Segment
ML3000 ML3000
EDH Ring
ML3000 ML3000
Profibus DP
Profibus DP / IEC61850
IO module IO module
Hard wired
control cmd
F650
Hard wired
M60
control cmd MM300
Small / non-critical Large / Critical VFD driven Small / non-critical Large / Critical VFD driven
MV Motors MV Motors MV Motors LV Motors LV Motors LV Motors
(differential protection) (non-smart starter)
Note:
Mark Vie have Profibus DP connection to control the motors.
ECS have IEC61850 or Modbus TCP for advance monitoring (include oscillo file auto retrieve).
Refer to ECS Note 4.
DISTR
ELECTRICAL MV/LV MOTOR STARTER TYPICAL DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 13 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 14 -
ML3000
ML3000
Bay controller
Essential Diesel Incomer / Coupler
for busbar metering
/ Feeder
and other non-smart
signal digitalization
Note:
ECS have IEC61850 for breaker control and advance monitoring (include oscillo file auto retrieve)
Refer to ECS Note 4
DISTR
ELECTRICAL MV/LV DIESEL DISTRIBUTION TYPICAL DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 14 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 15 A
Main eROOM GT12 Sec eROOM ACC eROOM GT11 Sec eROOM ROP eROOM
ML IED and E ML IED ML IED ML IED ML IED
MV VFD /LV MV VFD /LV
ECS Concentrator panel1 ECS Concentrator panel2 Edge Panel Switchboard / Aux LV Switchboard / Aux Switchboard / Aux Edge Panel
A5 A5
Patch BOX used for EDH ring Fiber connection from field (input and output): Easy Connection for armored FO cables.
DISTR
EDH TOPOLOGY OVERVIEW DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 15 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 16 -
MAIN eROOM
PDH A
PDH B
ECS CONCENTRATOR PANEL 1 ECS CONCENTRATOR PANEL 2
ML3000 ML3000
EDH Ring
ML3000 ML3000
ECS_ADM ECS_ADM
Note: This sheet gives PDH interconnect details from ECS concentrators to GT Mark Vie switches.
Master hot/stand-by GPGs A/B compile the slave GPGs data base and provide single interface to OPC gateways / HMI viewer.
Slave hot/stand-by GPG 11/12 process IEDs 001 to 250.
Slave hot/stand-by GPG 21/22 process IEDs 251 to 500.
Refer to ECS Note 3.
DISTR
ECS GPGs REDUNDANCY & PDH CONNECTION DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 16 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 17 -
NTP_1
2 x IRIG-B OUTPUT
1 1
Main eROOM
Note: This sheet gives IRIG-B interconnect details from master clock to ECS Concentrators and GPP/TPPs.
GPGs are synchronized in IRIG-B.
Main GPP/TPP protection panel IEDs are synchronized in IRIG-B with backup in NTP via GPGs.
Other IEDs with time stamp capability are synchronized in NTP via GPGs. SIZE CAGE CODE DWG NO
4110
Refer to note 6 j) and k). g GENERAL ELECTRIC COMPANY B
127T3686
DISTR
ECS GPGs & GPP/TPP TO MASTER CLOCK CONNECTION DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 17 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 18 A
MAIN EROOM
A1
GT11 GSUT
G60A T60U T60AT T60ET T60IT
WAGO
G60B T60T
GT11 UAT
WAGO TRANSFIX WAGO
Note: This sheet gives MSD IEDs to ECS concentrator panel switches interconnect details.
ML3000 and patch box fiber Connection (FO) are multimode with LC-100 Mb/s type ports. SIZE CAGE CODE DWG NO
4110
IEDs Connections are Cat-6 F/UTP with RJ45 ports.
g GENERAL ELECTRIC COMPANY B
MAIN eROOM GT11 MSD IEDs CONNECTIONS 127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO ECS PANEL SWITCHES
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 18 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 19 -
MAIN EROOM
A1
GT12 GSUT
G60A T60U T60AT T60ET T60IT
WAGO
G60B T60T
GT12 UAT
WAGO TRANSFIX WAGO
Note: This sheet gives MSD IEDs to ECS concentrator panel switches interconnect details.
ML3000 and patch box fiber Connection (FO) are multimode with LC-100 Mb/s type ports. SIZE CAGE CODE DWG NO
4110
IEDs Connections are Cat-6 F/UTP with RJ45 ports.
g GENERAL ELECTRIC COMPANY B
MAIN eROOM GT12 MSD IEDs CONNECTIONS 127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO ECS PANEL SWITCHES
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 19 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 20 -
Cable By
Cable By
Patch Box
ST GPP/TPP ST GSEC
ST GSUT
G60A T60U T60ET C650 WAGO
G60B T60T
WAGO TRANSFIX
Note: This sheet gives ST MSD IEDs to Edge panel switches interconnect details.
ML3000 and patch box fiber Connection (FO) are multimode with LC - 100 Mb/s type ports. SIZE CAGE CODE DWG NO
4110
IEDs Connections are Cat-6 F/UTP with RJ45 ports. g GENERAL ELECTRIC COMPANY B
MAIN eROOM ST MSD IEDs CONNECTIONS 127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO
SCALE SHEET
TO EDGE PANEL SWITCHES ISSUED SEE PLM SEE PLM 20 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 21 A
D F H J
ML3000-2
VFD PANEL
RS485/TCP
converter
A2
MM200
VFD
88BT1
Note: This sheet gives MSD IEDs to BHC12 Switchboard switches interconnect details.
ML3000 and patch box fiber Connection (FO) are multimode with LC type ports.
IEDs Connections are Cat-6 F/UTP with RJ45 ports.
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
MAIN eROOM MSD IEDs CONNECTIONS 127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO
SCALE SHEET
TO BHC12 SWITCHBOARD SWITCHES ISSUED SEE PLM SEE PLM 21 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 22 A
MAIN EROOM
ML1 Port # IEDs ML2 Port# IEDs
BMC10 1 C1 (LC) EDH-IN (FO) C1 (LC) EDH-IN (FO)
2 C2 (LC) EDH-OUT (FO) C2 (LC) EDH-OUT (FO)
3 C3 (LC) SPARE C3 (LC) SPARE
EDH Ring 4 C4 (LC) SPARE C4 (LC) SPARE
ML3000-1 C E G I 5 D1 (RJ45) 88BT2 D1 (RJ45) SPARE
A2
6 D2 (RJ45) SPARE D2 (RJ45) SPARE
D F H J 7 … … … …
ML3000-2
A7
VFD PANEL
A2
MM300
88BT2
Note: This sheet gives MSD IEDs to BMC10 Switchboard switches interconnect details.
ML3000 and patch box fiber Connection (FO) are multimode with LC type ports.
IEDs Connections are Cat-6 F/UTP with RJ45 ports.
SIZE CAGE CODE DWG NO
4110
g GENERAL ELECTRIC COMPANY B
MAIN eROOM MSD IEDs CONNECTIONS
127T3686
DISTR
DRAWN A. BENOIT 2018-02-20
TO BMC10 SWITCHBOARD SWITCHES
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 22 of 23
SIZE DWG. NO. SH. REV.
B 127T3686 23 -
DISTR
ACRONYMS DRAWN A. BENOIT 2018-02-20
TO
ISSUED SCALE SHEET
SEE PLM SEE PLM 23 of 23