Beruflich Dokumente
Kultur Dokumente
Lenovo
Repair Manual of Lenovo P70-A Mobile Phone
Preface
This manual is intended for online repair guidance and after-sale repair guidance of
Lenovo P70-A mobile phone produced by the Company
The content of this manual will be upgraded according to the needs of technology
development.
Copyright
The copyright of this manual belongs to Lenovo Mobile; anyone who reproduces this
manual without written consent of the Company shall bear legal responsibility.
1
Repair Manual of Lenovo P70-A Mobile Phone
Content
1. Appearance ............................................................................................................................. 5
3. Baseband................................................................................................................................. 7
2
Repair Manual of Lenovo P70-A Mobile Phone
3
Prepared/
Version Prepared by/ Reason for
Modified Main changes
No. Modified by change
on
1. Appearance
Repair Manual of Lenovo P70-A Mobile Phone
6
Repair Manual of Lenovo P70-A Mobile Phone
3. Baseband
7
Repair Manual of Lenovo P70-A Mobile Phone
4.1.1 No display on screen after power‐on
8
Repair Manual of Lenovo P70-A Mobile Phone
4.1.2 LCD backlight without lighting
N
Y
Check whether there are voltages more than If the backlight circuit is
24V between both ends of C1612 when LCD normal, it is the problem
is lit. of LCD
9
Repair Manual of Lenovo P70-A Mobile Phone
4.2.1 Rear camera defects
Y
Check to see whether the camera
OK
module connector is welded well;
whether the camera is OK after
overlaying welding the connector?
10
Repair Manual of Lenovo P70-A Mobile Phone
4.3.1 No vibration
No vibration
11
Repair Manual of Lenovo P70-A Mobile Phone
4.3.2 No ring
No ring
12
Repair Manual of Lenovo P70-A Mobile Phone
4.4 Charging
4.4.1 No charging display after plugging the charger in
Y
Check whether the charging is normal
Replace the charger
after replacing the charger (J801).
Y
Replace the battery and see whether the
Replace the battery
charging is normal? Measure the battery
voltage to see whether it is less than 3V
Y
Check to see whether U630 module
OK
device is well welded? Whether it is
normal after re-welding
N
Y
Replace U503 OK
13
Repair Manual of Lenovo P70-A Mobile Phone
4.4.2 Charging shown but not full charging
Y
Replace the battery and then check whether it
OK
is fully charged
N
Re-solder the USB connector
Check to see the Voltage of VCHG is Y
or change for another FPC ;
normal (5.0V), Check the VCDT Circuit
Re-solder or change the
& ISENSE Circuit components is normal
components which is damaged
(R523, R524, R551, R571,R663,R662 )
or in poor soldering
N
Y
Replace U503 OK
14
Repair Manual of Lenovo P70-A Mobile Phone
4.5.1 Abnormal operation of side keys
N
Y
FPC is fracted, Replace
OK
side keys FPC
Replace U401/U503
15
Repair Manual of Lenovo P70-A Mobile Phone
4.5.2 Abnormal operation of CTP keyboard
Y CTP damaged,
Whether the CTP test is normal?
replace it
16
Repair Manual of Lenovo P70-A Mobile Phone
4.6 Calling
4.6.1 No voice heard from the other side during the call
N
Cold solder joint
Use earphone and hands-free to verify of main
whether there is voice? chip(U503) or
main chip(U503)
Y is abnormal
Y
Replace the headphones and then re OK
check whether it is normal
Check whether Y
B1403,B1404,C1428,C1427,D1403,D140 OK
4,are well welded. Re-weld and test
Replace U503
17
Repair Manual of Lenovo P70-A Mobile Phone
4.6.2 No voice heard from your side during the call
18
Repair Manual of Lenovo P70-A Mobile Phone
Failed to Power-on
Y
Check whether the power key FPC is Re-weld
assembled well , reassembling the
power FPC ?
N
Check whether the 26MHz on X801
Re-weld and recheck
is normal? Whether there is 26MHz
signal
Y
N
Check whether X801 is well
Re-weld and recheck
welded
19
Repair Manual of Lenovo P70-A Mobile Phone
4.8 LCD on when close to the ear during the call; LCD off
when away from the ear.
Y
Check whether P-Sensor related circuit is p-sensor FPC
normal? Or replace p-sensor IC U1502 Problem
N
Y Replace the application
Whether the touch screen is well of gum of touch screen
pasted with the shell and re-paste
Check U401
20
Repair Manual of Lenovo P70-A Mobile Phone
Y
Check whether USB connector is Re-weld USB connector or
in cold solder joint use another KB to verify it
21
Repair Manual of Lenovo P70-A Mobile Phone
4.11.1 AFC calibration
AFC calibration
Fail
Recalibrate
22
Repair Manual of Lenovo P70-A Mobile Phone
4.11.2 AGC
N
N
Whether U801 Rx is in cold
Re-weld Y
solder joint?
N
Check the baseband chip
U401
23
Repair Manual of Lenovo P70-A Mobile Phone
4.11.3 APC
Fault 1
Fault: APC calibration Fail.
Cause: RF test cable is not connected well during calibration; PA is oppositely pasted; PA
and peripheral circuit are in cold solder joint; The patch of RF input circuit of PA is deviated
with short-circuit shield box.
Shooting:
N Whether PA is in N
cold solder joint? Y Replace PA
Weld PA Y Whether PA is in Whether related Y Re-weld
cold solder joint? components is in cold
solder joint?
24
Repair Manual of Lenovo P70-A Mobile Phone
Fault 2:
Fault: The output power of the mobile phone is too high.
Cause: The cable isn't well connected in calibration.
Shooting:
Fault 3:
Fault: After repeated calibration, the power is still low.
Cause: Some element patches of PA and surrounding VAPC input are displaced or PA is
damaged.
Shooting:
Related PA may be
partially damaged; N Replace Vramp
recalibrate. circuit
25
Repair Manual of Lenovo P70-A Mobile Phone
4.12.1 Switch spectrum & PVT template with excessive
standard
Fault: The switch spectrum and PVT template of GSM and DCS frequency bands are
excessive.
Cause: The cold solder joint or damage to components in V_ramp of PV may result in the
excessive switch spectrum.
Shooting:
26
Repair Manual of Lenovo P70-A Mobile Phone
4.12.2 High Frequency Error
Recalibrate
joint or damaged
4.12.3 High Phase Error
27
Repair Manual of Lenovo P70-A Mobile Phone
4.12.4 Power output problems
Fault: Normally power-on and receive, but when outputting two frequency bands or single
frequency band power, there is no input power or the input power is very low.
Cause: There are many reasons for no output power or very low power, which may be the
results of faults of Transceiver output part, PA input and output circuit, antenna connector
and antenna switch control signal or power supply circuit. Specific circumstances are:
RF connector(J1001/J1002)
Checking: Whether RF connector J1001/J1002 and the test probe of RF test cable are
well connected or the patch is oppositely pasted or the antenna connector is damaged.
Shooting: Replace antenna connector and ensure right direction of patch.
Transceiver(U801)
A. Whether the power supply voltage of Transceiver(U801) is within normal range;
check the power supply voltage between power supply filtration capacitor and U801
connection and then check whether the surrounding circuit is in cold solder joint.
B. Whether there is cold solder joint or short circuit in Transceiver (U801).
28
Repair Manual of Lenovo P70-A Mobile Phone
If it is possible to repair the complete set, the output power of each module on
transmission channel can be detected through spectrum analyzer probes when keeping the
phone in the constant state of maximum power. Under normal circumstances,
A. About GSM 33dBm and DCS/PCS 30dBm output power can be detected on the
output end of RF connector.
B. About 3dBm output power can be detected on matching circuit parts of PA input end;
C. About 32dBm or 29dBm output power can be respectively detected on pinD11
connection of PA output end;
D. About 3dBm output power can be detected on Transceiver (U801) output end.
4.13.1 RSSI _Cal
RSSI _cal
RSSI Fail?
Whether TX module Y
U801,U901,U902 and RF Re-weld
connector J1001 are in cold
4.13.2 TPC _ Cal
29
Repair Manual of Lenovo P70-A Mobile Phone
TPC
30
Repair Manual of Lenovo P70-A Mobile Phone
4.14.1 ACLR or SEM
ACLR or SEM
Re-weld or replace
transceiver
4.14.2 ILPC comprehensive test abnormal
Fault: ILPC
Cause: No calibration or just passing calibration.
Repair manner: The same as 4.5.1.
4.14.3 Frequency Err
31
Repair Manual of Lenovo P70-A Mobile Phone
5. Disassembly Guide
(1) Remove the battery cover
Divides the battery cover is separated from B shell from your mobile phone at the
Figure 1
Figure 2
32
Repair Manual of Lenovo P70-A Mobile Phone
Figure 3
(3) Remove the B shell
Break open outward the top right corner to B shell. According to the order(1-4) of the
figure 4 in turn to open B shell. Or use A teardown piece is separated from A shell.
Figure 4
33
Repair Manual of Lenovo P70-A Mobile Phone
Apart after B shell as shown in figure 5, and then remove the red circle marked two screws of antenna
pedestal.
Figure 5
(4) Separate the A shell and PCB mainboard LCD/motor/TP/side key/camera/battery
FPC.
Open the CTP,LCD’s FPC cover, then pull out the FPC Then separate the A shell of the joint
surface and side key/camera/battery FPC/moto,as shown in figure 6.
Figure 6
34
Repair Manual of Lenovo P70-A Mobile Phone
Figure 7
Figure 8
35
Repair Manual of Lenovo P70-A Mobile Phone
Figure 9
36
Repair Manual of Lenovo P70-A Mobile Phone
Take off the receiver from A shell with forceps, don't bend the shrapnel. Remove the
light induced rubber lining,as shown in figure 10.
Figure 10
(7) Remove the TP
Oven heated the TP (temperature at 80℃ for 10 minutes), with suction cups on the TP from A
shell will be removed.Notice: First from the right side of the TP split up in central, with teardown
card along the clockwise direction, TP is separated from A shell, In separate to the top when
should pay attention to protect the FPC, slow down to action ,avoid the FPC is torn. After the
TP removed, use film to protective the LCD and TP,as shown in figure 11/12/13.
Figure 11
37
Repair Manual of Lenovo P70-A Mobile Phone
Figure 12
Figure 13
Use the soldering iron to remove the motor wire/side key FPC from the motherboard,as shown
in figure 14.
38
Repair Manual of Lenovo P70-A Mobile Phone
Figure 14
39
Repair Manual of Lenovo P70-A Mobile Phone
Figure 15
6. Assemble Guide
Please refer to disassembly Guide , assembly process in contrary to the disassemble process.
40