Beruflich Dokumente
Kultur Dokumente
SECTION
EXTERIOR LIGHTING SYSTEM
EXL B
E
CONTENTS
XENON TYPE System Diagram ......................................................19 F
System Description ..................................................19
BASIC INSPECTION .................................... 6 Component Parts Location ......................................20
Component Description ..........................................20 G
DIAGNOSIS AND REPAIR WORKFLOW .......... 6
Work Flow ................................................................. 6 EXTERIOR LAMP BATTERY SAVER SYS-
TEM ................................................................... 21
FUNCTION DIAGNOSIS ............................... 8 System Diagram ......................................................21 H
System Description ..................................................21
HEADLAMP SYSTEM ......................................... 8
Component Parts Location ......................................22
System Diagram ........................................................ 8
Component Description ..........................................22 I
System Description ................................................... 8
Component Parts Location ........................................ 9 DIAGNOSIS SYSTEM (BCM) ........................... 23
Component Description .......................................... 10
COMMON ITEM .........................................................23 J
DAYTIME RUNNING LIGHT SYSTEM ..............11 COMMON ITEM : CONSULT-III Function (BCM -
System Diagram ...................................................... 11 COMMON ITEM) .....................................................23
System Description ................................................. 11 K
Component Parts Location ...................................... 12 HEADLAMP ...............................................................24
Component Description .......................................... 12 HEADLAMP : CONSULT-III Function (BCM -
HEAD LAMP) ...........................................................24
AUTO LIGHT SYSTEM ......................................13 EXL
System Diagram ...................................................... 13 FLASHER ...................................................................26
System Description ................................................. 13 FLASHER : CONSULT-III Function (BCM -
Component Parts Location ...................................... 14 FLASHER) ...............................................................26
M
Component Description .......................................... 14
DIAGNOSIS SYSTEM (IPDM E/R) ................... 28
FRONT FOG LAMP SYSTEM ............................15 Diagnosis Description ..............................................28
System Diagram ...................................................... 15 CONSULT-III Function (IPDM E/R) .........................31 N
System Description ................................................. 15
Component Parts Location ...................................... 16
COMPONENT DIAGNOSIS ......................... 34
Component Description .......................................... 16 POWER SUPPLY AND GROUND CIRCUIT .... 34 O
TURN SIGNAL AND HAZARD WARNING BCM (BODY CONTROL MODULE) ..........................34
LAMP SYSTEM ..................................................17 BCM (BODY CONTROL MODULE) : Diagnosis
System Diagram ...................................................... 17 P
Procedure ................................................................34
System Description ................................................. 17
Component Parts Location ...................................... 18 IPDM E/R (INTELLIGENT POWER DISTRIBU-
Component Description .......................................... 18 TION MODULE ENGINE ROOM) ..............................34
IPDM E/R (INTELLIGENT POWER DISTRIBU-
PARKING, LICENSE PLATE AND TAIL TION MODULE ENGINE ROOM) : Diagnosis Pro-
LAMPS SYSTEM ................................................19 cedure ......................................................................34
FRONT FOG LAMP AIMING ADJUSTMENT .. 161 DIAGNOSIS AND REPAIR WORKFLOW ...... 179
Description ............................................................ 161 Work Flow .............................................................. 179 J
Aiming Adjustment Procedure ............................... 161
FUNCTION DIAGNOSIS ............................ 181
ON-VEHICLE REPAIR ............................... 163
HEADLAMP SYSTEM ..................................... 181 K
FRONT COMBINATION LAMP ........................ 163 System Diagram .................................................... 181
Exploded View ...................................................... 163 System Description ................................................ 181
Removal and Installation ....................................... 164 Component Parts Location .................................... 182
Replacement ......................................................... 164 EXL
Component Description ........................................ 182
Disassembly and Assembly .................................. 165
DAYTIME RUNNING LIGHT SYSTEM ........... 183
FRONT FOG LAMP .......................................... 166 System Diagram .................................................... 183 M
Exploded View ...................................................... 166 System Description ................................................ 183
Removal and Installation ....................................... 166 Component Parts Location .................................... 184
Replacement ......................................................... 166 Component Description ........................................ 184 N
OPTICAL SENSOR .......................................... 168 FRONT FOG LAMP SYSTEM ......................... 185
Exploded View ...................................................... 168 System Diagram .................................................... 185
Removal and Installation ....................................... 168 System Description ................................................ 185 O
LIGHTING & TURN SIGNAL SWITCH ............ 169 Component Parts Location .................................... 186
Component Description ........................................ 186
Exploded View ...................................................... 169
Removal and Installation ....................................... 169 P
TURN SIGNAL AND HAZARD WARNING
HAZARD SWITCH ............................................ 170 LAMP SYSTEM ............................................... 187
Exploded View ...................................................... 170 System Diagram .................................................... 187
Removal and Installation ....................................... 170 System Description ................................................ 187
Component Parts Location .................................... 188
HEADLAMP AIMING SWITCH ........................ 171 Component Description ........................................ 188
Exploded View ...................................................... 171
EXTERIOR LAMP BATTERY SAVER SYS- TURN SIGNAL LAMP CIRCUIT ....................... 217
Description ............................................................ 217
TEM .................................................................. 191
Component Function Check ................................. 217
System Diagram ....................................................191
Diagnosis Procedure ............................................. 217
System Description ................................................191
Component Parts Location ....................................192 HAZARD SWITCH ............................................ 219
Component Description ........................................192 Component Function Check ................................. 219
Diagnosis Procedure ............................................. 219
DIAGNOSIS SYSTEM (BCM) .......................... 193
COMMON ITEM .......................................................193
TAIL LAMP CIRCUIT ....................................... 221
Component Function Check ................................. 221
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ...................................................193 Diagnosis Procedure ............................................. 221
POWER SUPPLY AND GROUND CIRCUIT ... 204 TURN SIGNAL AND HAZARD WARNING
LAMP SYSTEM ................................................ 236
BCM (BODY CONTROL MODULE) ........................204 Wiring Diagram - TURN AND HAZARD WARN-
BCM (BODY CONTROL MODULE) : Diagnosis ING LAMPS - ........................................................ 236
Procedure ..............................................................204
PARKING, LICENSE PLATE AND TAIL
IPDM E/R (INTELLIGENT POWER DISTRIBU- LAMPS SYSTEM .............................................. 240
TION MODULE ENGINE ROOM) ............................204 Wiring Diagram - PARKING, LICENSE PLATE
IPDM E/R (INTELLIGENT POWER DISTRIBU- AND TAIL LAMPS - .............................................. 240
TION MODULE ENGINE ROOM) : Diagnosis Pro-
cedure ....................................................................204 STOP LAMP ..................................................... 246
Wiring Diagram - STOP LAMP - ........................... 246
EXTERIOR LAMP FUSE ................................. 206
Description .............................................................206 BACK-UP LAMP .............................................. 249
Diagnosis Procedure .............................................206 Wiring Diagram - BACK-UP LAMP - ..................... 249
BOTH SIDE FRONT FOG LAMPS ARE NOT REAR COMBINATION LAMP ......................... 323
TURNED ON ..................................................... 309 Exploded View ....................................................... 323
Removal and Installation ....................................... 323 H
Description ............................................................ 309
Diagnosis Procedure ............................................. 309 Replacement ......................................................... 324
FOR USA AND CANADA ........................................ 310 BACK-UP LAMP ............................................. 326 J
FOR USA AND CANADA : Precaution for Supple- Exploded View ....................................................... 326
mental Restraint System (SRS) "AIR BAG" and Removal and Installation ....................................... 326
"SEAT BELT PRE-TENSIONER" .......................... 310 Replacement ......................................................... 326 K
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000003261288
OVERALL SEQUENCE
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
>> GO TO 4. D
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected? E
YES >> GO TO 5.
NO >> GO TO 6.
F
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
G
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK H
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7. I
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part. J
>> GO TO 9.
K
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
EXL
>> GO TO 9.
9.MALFUNCTION PART REPAIR M
Repair or replace the malfunctioning part.
>> GO TO 10. N
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is O
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5. P
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
FUNCTION DIAGNOSIS
HEADLAMP SYSTEM
System Diagram INFOID:0000000003261555
JPLIA1036GB
OUTLINE
• Mobile valve shade type is adopted. Xenon headlamp switches the high beam and the low beam with one
xenon bulb each on right and left.
• Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP BASIC OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R with CAN communication according to the head-
lamp ON condition.
Headlamp ON condition
- Lighting switch 2ND
- Lighting switch PASS
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP HI/LO SWITCHING OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter with CAN communica-
tion according to the high beam switching condition.
High beam switching condition
- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
G
JPLIA0802ZZ
EXL
JPLIA0839ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges that the headlamp is turned ON according to the vehicle condition.
BCM - Requests the headlamp relay (HI/LO) ON to IPDM E/R (with CAN communication).
- Requests the high beam indicator lamp ON to the combination meter (with CAN
communication).
Controls the integrated relay, and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Combination meter Turns the high beam indicator lamp ON according to the request from BCM (with CAN
(High beam indicator lamp) communication).
• HID control unit
Headlamp assem- Refer to EXL-40, "Description".
• Xenon bulb
bly
High beam solenoid Refer to EXL-37, "Description".
JPLIA0803GB F
G
OUTLINE
• Turns the front fog lamp ON as the daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading H
function of BCM, and relay control function of IPDM E/R.
DAYTIME RUNNING LIGHT OPERATION
• BCM detects the combination switch condition by the combination switch reading function. I
• BCM detects the vehicle condition depending on the following signals.
- Engine condition signal (received from ECM with CAN communication)
- Parking brake switch signal (received from combination meter with CAN communication) J
• BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the day-
time running light ON condition.
Daytime running light ON condition K
- While the engine running with the parking brake released
Daytime running light OFF condition
- Engine stopped EXL
- Headlamp ON (Passing included)
• IPDM E/R turns the integrated front fog lamp relay ON and turns the front fog lamp ON according to the front
fog light request signal. M
JPLIA0841ZZ
Part Description
• Detects each switch condition with the combination switch reading function.
BCM • Judges the headlamp ON/OFF status according to the vehicle condition. Requests
the front fog lamp relay ON to IPDM E/R (with CAN communication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
ECM Transmits the engine condition signal to BCM with CAN communication.
Combination meter Transmits the parking brake switch signal to BCM with CAN communication.
JPLIA0804GB
G
System Description INFOID:0000000003269348
OUTLINE H
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function I
- Headlamp control function
- Auto light function
- Delay timer function J
JPLIA0840ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges the outside brightness from the optical sensor signal.
• Judges the OFF timing according to the vehicle condition.
BCM
• Judges the ON/OFF status of the exterior lamp and each illumination according to the
outside brightness and the vehicle condition.
Requests ON/OFF of each relay to IPDM E/R (with CAN communication).
Controls the integrated relay, and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Optical sensor Refer to EXL-52, "Description".
JPLIA0004GB F
G
OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R. H
FRONT FOG LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the front I
fog lamp ON condition.
Front fog lamp ON condition J
- Front fog lamp switch ON with headlamp ON (except for the high beam ON)
• IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the
front fog light request signal.
K
EXL
JPLIA0843ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
BCM • Judges the front fog lamp ON/OFF status according to the vehicle condition.
- Requests the front fog lamp relay ON to IPDM E/R (with CAN communication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
JPLIA0180GB F
G
OUTLINE
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM. H
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the I
turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
J
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the
hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION K
• BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn sig-
nal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn indicator signal. EXL
JPLIA0844ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges the blinks of the turn signal lamp and the hazard warning lamp from each
BCM switch status. The applicable turn signal lamp blinks.
• Requests the turn signal indicator lamp blink to the combination meter (with CAN
communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Hazard switch Inputs the hazard switch ON/OFF signal to BCM.
Combination meter Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
(Turn signal indicator lamp & buzzer) integrated buzzer according to the request from BCM (with CAN communication).
JPLIA0805GB F
G
OUTLINE
Parking, license plate, side marker and tail lamps are controlled by combination switch reading function and
headlamp control function of BCM, and relay control function of IPDM E/R. H
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter with CAN communi- I
cation according to the ON/OFF condition of the parking, license plate, side marker and tail lamps.
Parking, license plate, side marker and tail lamps ON condition J
- Lighting switch 1ST
- Lighting switch 2ND
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking lamp, license plate, side marker and
tail lamps ON according to the position light request signal. K
• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
EXL
JPLIA0842ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges the ON/OFF status of the parking, license plate and tail lamps according to
the vehicle condition.
BCM
- Requests the tail lamp relay ON to IPDM E/R (with CAN communication).
- Requests the tail lamp indicator lamp ON to the combination meter (with CAN com-
munication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Combination meter Turns the tail lamp indicator lamp ON according to the request from BCM (with CAN
(Tail lamp indicator lamp) communication).
JPLIA1037GB F
G
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
H
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function I
JPLIA0845ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Activates the battery saver to turn the exterior lamps OFF according to the vehicle
BCM
condition.
- Requests each relay OFF to IPDM E/R (with CAN communication).
Controls the integrated relay according to the request from BCM (with CAN communi-
IPDM E/R
cation).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT* 1 × × × K
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × ×
EXL
Turn signal and hazard warning lamps FLASHER × × ×
— AIR CONDITONER*2
• Intelligent Key system M
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM × N
NVIS - NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
O
Back door opener system TRUNK × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × P
Signal buffer system SIGNAL BUFFER × ×
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
• *1:At model with Intelligent Key system this item is displayed, but is not used.
• *2: This item is displayed, but is not used.
IGN Counter
IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected.
• The number is 0 when a malfunction is detected now.
• The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition
switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000003420470
WORK SUPPORT
CUSTOM A/LIGHT SET- MODE 2 More sensitive setting than normal setting (Turns ON earlier than normal operation.) E
TING MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
*: Initial setting F
DATA MONITOR
G
Monitor item
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch H
[On/Off]
ENGINE STATE
The engine status received from ECM with CAN communication
[Stop/Stall/Crank/Run]
I
VEH SPEED 1 The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication
KEY SW-SLOT
Key switch status input from key slot J
[On/Off]
TURN SIGNAL R
[On/Off]
K
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off] EXL
HI BEAM SW
[On/Off]
HEAD LAMP SW1 M
Each switch status that BCM detects from the combination switch reading function
[On/Off]
HEAD LAMP SW2
[On/Off] N
PASSING SW
[On/Off]
AUTO LIGHT SW O
[On/Off]
FR FOG SW
[On/Off] P
RR FOG SW NOTE:
[On/Off] The item is indicated, but not monitored.
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
ACTIVE TEST
On NOTE:
DAYTIME RUNNING LIGHT
Off The item is indicated, but cannot be tested.
RH
NOTE:
CORNERING LAMP LH
The item is indicated, but cannot be tested.
Off
On NOTE:
ILL DIM SIGNAL
Off The item is indicated, but cannot be tested.
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000003420471
WORK SUPPORT
DATA MONITOR
Monitor item A
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
B
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW C
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function D
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch E
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
F
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC
Panic alarm signal status received from the remote keyless entry receiver G
[On/Off]
ACTIVE TEST
H
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. I
Off Stops the voltage to turn the turn signal lamps OFF.
EXL
JPMIA0871ZZ
Operation A
Inspection location Operation
sequence
A Oil pressure warning lamp Blinks continuously during operation of auto active test
1 Front wiper LO for 5 seconds → HI for 5 seconds B
• Parking lamps
• License plate lamps
2 • Side maker lamps 10 seconds C
• Tail lamps
• Front fog lamps
3 Headlamps LO ⇔ HI 5 times
D
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
E
Inspection in Auto Active Test Mode (Halogen Headlamp Models)
When auto active test mode is actuated, the following 5 steps are repeated 3 times.
JPMIA0872ZZ
J
Operation
Inspection location Operation
sequence K
A Oil pressure warning lamp Blinks continuously during operation of auto active test
1 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
EXL
• License plate lamps
2 • Side maker lamps 10 seconds
• Tail lamps M
• Front fog lamps
• LO 10 seconds
3 Headlamps
• HI ON ⇔ OFF 5 times
N
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
O
JPMIA0909GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R. F
ACTIVE TEST
Test item
EXL
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000003737071
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure INFOID:0000000003729397
Terminals
(+) Voltage F
(−)
IPDM E/R (Approx.)
Connector Terminal
Ground G
E9 1 Battery voltage
Is the measurement value normal?
YES >> GO TO 3. H
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
I
Check continuity between IPDM E/R harness connectors and ground.
IPDM E/R
Continuity J
Connector Terminal
Ground
E10 12
Existed
E11 41 K
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector. EXL
Fuse list
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #54 10 A
Headlamp HI (RH) IPDM E/R #55 10 A
Headlamp LO (LH) IPDM E/R #56 15 A
Headlamp LO (RH) IPDM E/R #57 15 A
Front fog lamp IPDM E/R #58 15 A
• Parking lamp
IPDM E/R #52 10 A
• Front side marker lamp
• Tail lamp
• Rear side marker lamp
IPDM E/R #53 10 A
• License plate lamp
• Each illumination
Stop lamp FUSE BLOCK (J/B) #7 10 A
Back-up lamp FUSE BLOCK (J/B) #4 10 A
1.CHECK FUSE
Check that the following fuses are not fusing.
The high beam solenoid drives the mobile valve shade. And the mobile valve shade switches the high beam B
and low beam of headlamp.
• When the headlamp high relay is turned ON, magnetic force is
applied to the high beam solenoid (1) by a current. The mobile
valve shade (3) is switched to the high beam position through the C
actuator rod (2).
• When the headlamp high relay is turned OFF, the current stops.
The mobile valve shade returns to the low beam position automati- D
cally.
JPLIA0802ZZ I
Component Function Check INFOID:0000000003261560
NOTE:
HI/LO is repeated 1 second each.
N
Does the headlamp switch to the high beam?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-37, "Diagnosis Procedure".
O
Diagnosis Procedure INFOID:0000000003261561
Terminals
Condition
(+) (−) Voltage
IPDM E/R (Approx.)
External
Connector Terminal lamp
Battery
Hi
RH 89 voltage
Ground
Off 0V
E345
Battery
Hi
LH 90 voltage
Off 0V
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the high beam solenoid harness connec-
tor.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 89
E345 Not existed
LH 90
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
EXL
Headlamp (LO) circuit is connected to HID control unit integrated in the headlamp. Headlamp (LO) circuit turns
xenon headlamp ON.
For the details of HID control unit and the xenon headlamp, refer to EXL-42, "Description".
Component Function Check INFOID:0000000003261563
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF
Is the headlamp (LO) turned ON?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-40, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000003261564
Terminals
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
External
Connector Terminal lamp
Battery volt-
Lo
RH 83 age
Ground
Off 0V
E345
Battery volt-
Lo
LH 84 age
Off 0V
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the headlamp harness connector.
E
Unit Lotion Fuse No. Capacity
Headlamp LO (RH) IPDM E/R #57 15 A
Headlamp LO (LH) IPDM E/R #56 15 A F
Is the fuse fusing?
YES >> GO TO 4.
NO >> Replace IPDM E/R. G
4.CHECK HEADLAMP (LO) SHORT CIRCUIT
1. Disconnect IPDM E/R connector. H
2. Check continuity between the IPDM E/R harness connector and the ground.
IPDM E/R
Continuity I
Connector Terminal
Ground
RH 83
E345 Not existed
LH 84 J
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
K
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
5.CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
Check continuity between the headlamp harness connector and the ground. EXL
Headlamp
Continuity M
Connector Terminal
Ground
RH E324 2
Existed
LH E323 2
N
Does continuity exist?
YES >> Perform the xenon headlamp diagnosis. Refer to EXL-42, "Description".
NO >> Repair the harnesses or connectors. O
OUTLINE
• The lamp light source is by the arch discharge by applying high voltage into the xenon gas-filled bulb instead
of the halogen bulb filament.
• Sight becomes more natural and brighter because the amount of light are gained adequately and the color of
light is sunshine-like white.
• The xenon bulb drops the amount of light, repeats blinking, and illuminates in red if the bulb reaches the ser-
vice life.
ILLUMINATION PRINCIPLE
1. Discharging starts in high voltage pulse between bulb elec-
trodes.
2. Xenon gas is activated by current between electrodes. Pale light
is emitted.
3. The luminous tube (bulb) temperature elevates. Evaporated
halide is activated by discharge. The color of light changes into
white.
NOTE:
• Brightness and the color of light may change slightly immediately
after the headlamp turned ON until the xenon bulb becomes sta-
ble. This is not malfunction.
JPLIA0421GB
• Illumination time lag may occur between right and left. This is not
malfunction.
PRECAUTIONS FOR TROUBLE DIAGNOSIS
Representative malfunction examples are; "Light does not turn ON", "Light blinks", and "Brightness is inade-
quate." The cause often be the xenon bulb. Such malfunctions, however, are occurred occasionally by HID
control unit malfunction or lamp case malfunction. Specify the malfunctioning part with diagnosis procedure.
WARNING:
• Never touch the harness, HID control unit, the inside and metal part of lamp when turning the head-
lamp ON or operating the lighting switch.
• Never work with wet hands.
CAUTION:
• Never perform HID control unit circuit diagnosis with a circuit tester or an equivalent.
• Temporarily install the headlamps on the vehicle. Connect the battery to the connector (vehicle side)
when checking ON/OFF status.
• Disconnect the battery negative terminal before disconnecting the lamp socket connector or the har-
ness connector.
• Check for fusing of the fusible link(s), open around connector, short, disconnection if the symptom
is caused by electric error.
NOTE:
• Turn the switch OFF once before turning ON, if the ON/OFF is inoperative.
• The xenon bulb drops the amount of light, repeats blinking, and illuminates in red if the bulb reaches the ser-
vice life.
Diagnosis Procedure INFOID:0000000003261324
EXL
IPDM E/R
Continuity
Connector Terminal
Ground
RH 86
E345 Not existed
LH 87
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
3.CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 4.
NO >> Replace the bulb.
4.CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect the front fog lamp connector.
2. Turn the ignition switch ON.
3. Select “EXTERNAL LAMP” of IPDM E/R active test item.
Terminals
Test item
(+) (−) B
Voltage
IPDM E/R (Approx.)
EXTERNAL
Connector Terminal LAMP
C
Battery
Fog
RH 86 voltage
Ground
Off 0V D
E345
Battery
Fog
LH 87 voltage
Off 0V E
Is the measurement value normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R. F
5.CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF. G
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front fog lamp harness connector.
H
IPDM E/R Front fog lamp
Continuity
Connector Terminal Connector Terminal
RH 86 E402 1 I
E345 Existed
LH 87 E331 1
Does continuity exist?
J
YES >> GO TO 6.
NO >> Repair the harnesses or connectors.
6.CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT K
Check continuity between the front fog lamp harness connector and the ground.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 91
E346 Not existed
LH 92
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
3.CHECK PARKING LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 4.
NO >> Replace the bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect the parking lamp connector.
2. Turn the ignition switch ON.
3. Select “EXTERNAL LAMP” of IPDM E/R active test item.
Terminals
Test item
(+) (−) B
Voltage
IPDM E/R (Approx.)
EXTERNAL
Connector Terminal LAMP
C
Battery
TAIL
RH 91 voltage
Ground
Off 0V D
E346
Battery
TAIL
LH 92 voltage
Off 0V E
Is the measurement value normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R. F
5.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF. G
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the parking lamp harness connector.
H
IPDM E/R Parking lamp
Continuity
Connector Terminal Connector Terminal
RH 91 E330 2 I
E346 Existed
LH 92 E329 2
Does continuity exist?
J
YES >> GO TO 6.
NO >> Repair the harnesses or connectors.
6.CHECK PARKING LAMP GROUND OPEN CIRCUIT K
Check continuity between the parking lamp harness connector and the ground.
NOTE:
Check the parking lamp circuit if the parking lamp and the front side marker lamp are not turned ON. Refer to
EXL-46, "Component Function Check".
1.CHECK FRONT SIDE MARKER LAMP OPERATION
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to .PCS-11, "Diagnosis Description"
2. Check that the front side marker lamp is turned ON.
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMP” of IPDM E/R active test item.
2. With operating the test items, check that the front side marker lamp is turned ON.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 91
E346 Not existed
LH 92
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
3.CHECK FRONT SIDE MARKER LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES >> GO TO 4.
NO >> Replace the bulb.
4.CHECK FRONT SIDE MARKER LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect the front side marker lamp connector.
Battery
TAIL D
RH 91 voltage
Ground
Off 0V
E346
Battery
TAIL E
LH 92 voltage
Off 0V
Is the measurement value normal? F
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT G
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front side marker lamp harness con- H
nector.
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function Check INFOID:0000000003261330
Terminals
Condition
(+) (−)
Voltage (Approx.)
BCM Turn signal
Connector Terminal switch
RH 17
Ground
LH or RH
M119
LH 18
PKID0926E
OFF 0V
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-88, "Exploded View".
BCM
Continuity I
Connector Terminal
Ground
RH 17
M119 Not existed
LH 18 J
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 5. K
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between the front turn signal lamp, or the rear combination lamp and the ground. EXL
Front turn signal lamp
Optical sensor converts the outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
Component Function Check INFOID:0000000003420418
Terminals
(+) (−) Voltage
Optical sensor (Approx.)
Terminals
(+) (−) Voltage
Optical sensor (Approx.)
Optical sensor
Continuity EXL
Connector Terminal Ground
M17 1 Not existed
Does continuity exist? M
YES >> Repair the harnesses or connectors.
NO >> Replace BCM.
6.CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT N
1. Turn the ignition switch OFF.
2. Disconnect the optical sensor connector and BCM connector.
3. Check continuity between the optical sensor harness connector and the BCM harness connector. O
Optical sensor
Continuity
Connector Terminal Ground
M17 2 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> Replace BCM.
H
Terminals
Condition
(+) (−)
Voltage (Approx.)
BCM I
Hazard switch
Connector Terminal
ON 0V
J
Ground
M122 110 K
OFF
JPMIA0154GB
EXL
Hazard switch
Continuity
Connector Terminal Ground
M45 2 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 4.
4.CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between the hazard switch harness connector and the ground.
Hazard switch
Continuity
Connector Terminal Ground
M45 1 Existed
Does continuity exist?
YES >> Replace the hazard switch.
NO >> Repair the harnesses or connectors.
NOTE: B
Check the license plate lamp circuit if the tail lamp and the license plate lamp are not turned ON. Refer to EXL-
59, "Component Function Check".
1.CHECK TAIL LAMP OPERATION C
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "Diagnosis Description".
2. Check that the tail lamp is turned ON. D
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMP” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON. E
Terminals N
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
EXTERNAL O
Connector Terminal LAMP
Ground Battery volt-
TAIL
E10 7 age
P
Off 0V
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace IPDM E/R.
3.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
JCLWM1139GB
EXL
JCLWM1140GB
JCLWM1141GB
EXL
JCLWM1142GB
JCLWM1147GB
EXL
JCLWM1148GB
JCLWM1149GB
EXL
JCLWM1150GB
JCLWM1151GB
EXL
P
JCLWM1152GB
JCLWM1153GB
EXL
JCLWM1154GB
JCLWM1155GB
EXL
JCLWM1156GB
The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor inte-
grated in the front combination lamp.
Wiring Diagram - HEADLAMP AIMING CONTROL SYSTEM (MANUAL) - INFOID:0000000003261525
JCLWM1157GB
EXL
JCLWM1158GB
0 A: 910 Ω
1 B: 576 Ω
2
1 2 C: 374 Ω
3 D: 240 Ω JSLIA0084ZZ
3 — E: 390 Ω
Is the measurement value normal?
YES >> Headlamp aiming switch is normal.
NO >> Replace the headlamp aiming switch.
EXL
P
JCLWM1159GB
JCLWM1160GB
EXL
JCLWM1161GB
JCLWM1162GB
EXL
JCLWM1163GB
JCLWM1164GB
EXL
JCLWM1165GB
JCLWM1172GB
EXL
JCLWM1173GB
JCLWM1174GB
EXL
JCLWM1175GB
JCLWM1176GB
EXL
JCLWM1177GB
JCLWM1166GB
EXL
JCLWM1167GB
JCLWM1168GB
EXL
P
JCLWM1169GB
JCLWM1170GB
EXL
JCLWM1171GB
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000003729398
The key ID that the key slot receives does not accord with the fourth
Yet
key ID registered to BCM.
CONFIRM ID4 N
The key ID that the key slot receives accords with the fourth key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the third
Yet O
key ID registered to BCM.
CONFIRM ID3
The key ID that the key slot receives accords with the third key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the sec-
P
Yet
ond key ID registered to BCM.
CONFIRM ID2
The key ID that the key slot receives accords with the second key
DONE
ID registered to BCM.
EXL
JPMIA0062ZZ
P
PHYSICAL VALUES
7 ON 0V
Ground Step lamp Output Step lamp
(W) OFF Battery voltage
LOCK (Actuator is activat-
Battery voltage
8 ed)
Ground All doors LOCK Output All doors
(V) Other than LOCK (Actuator
0V
is not activated)
UNLOCK (Actuator is acti-
Battery voltage
9 vated)
Ground Driver door UNLOCK Output Driver door
(G) Other than UNLOCK (Actu-
0V
ator is not activated)
UNLOCK (Actuator is acti-
Rear RH door and Battery voltage
10 Rear RH door vated)
Ground rear LH door UN- Output
(P) and rear LH door Other than UNLOCK (Actu-
LOCK 0V
ator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(LG)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position
Push-button ignition
14
Ground switch illumination Output Tail lamp
(O) ON
ground
JSNIA0010GB
17
Ground Turn signal RH Output
Ignition switch C
(G) ON Turn signal switch RH
D
PKID0926E
6.5 V
Turn signal switch OFF 0V
E
18 Ignition switch F
Ground Turn signal LH Output
(BR) ON Turn signal switch LH
G
PKID0926E
6.5 V
JMKIA0062GB M
34*1 Ground
Luggage room anten-
Output
Ignition switch
(B) na 1 (-) OFF
N
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
When the back
38*1 Ground
Rear bumper anten-
Output
door request
(L) na (-) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
When the back
39*1 Ground
Rear bumper anten-
Output
door request
(BR) na (+) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
61*1 Ground
Back door request
Input
Back door re-
(R) switch quest switch OFF (Not pressed) E
JPMIA0016GB
F
1.0 V
1.0 V
Not in stop position 0V J
K
OFF (When back door
66 closes)
Ground Back door switch Input Back door switch
(Y) EXL
JPMIA0011GB
11.8 V
ON (When back door M
0V
opens)
Pressed 0V
N
JPMIA0011GB P
11.8 V
11.8 V
ON (When rear RH door
0V
opens)
11.8 V
ON (When rear LH door
0V
opens)
JMKIA0062GB
72*1 Ground
Room antenna 2 (-)
Output
Ignition switch
(B) (center console) OFF
JMKIA0063GB
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
JMKIA0062GB
I
When the pas-
74*1 Ground
Passenger door an-
Output
senger door re-
(Y) tenna (-) quest switch is
operated with ig- J
nition switch OFF
When Intelligent Key is not
in the antenna detection
K
area
JMKIA0063GB
EXL
M
When Intelligent Key is in
the antenna detection area
N
JMKIA0062GB
When the pas-
75*1 Ground
Passenger door an-
Output
senger door re-
(LG) tenna (+) quest switch is O
operated with ig-
nition switch OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB
JMKIA0063GB
JMKIA0062GB
When the driver
77*1 Ground
Driver door antenna
Output
door request
(P) (+) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
78*1 Ground
Room antenna (-) (in-
Output
Ignition switch
(R) strument panel) OFF
JMKIA0063GB
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
During waiting
K
JMKIA0064GB
N
JMKIA0065GB
JPMIA0041GB
1.4 V
JPMIA0037GB
JPMIA0039GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0036GB
1.3 V
G
JPMIA0037GB
I
1.3 V
JPMIA0039GB
1.3 V EXL
1.3 V
Push-button igni- Pressed 0V O
89 Push-button ignition
Ground Input tion switch (push
(BR) switch (push switch) Not pressed Battery voltage
switch)
90 Input/ P
Ground CAN - L — —
(P) Output
91 Input/
Ground CAN - H — —
(L) Output
92
Key slot illumina-
(R)*1 Ground Key slot illumination Output Blinking
tion
(L)*2
JPMIA0015GB
6.5 V
ON 0V
OFF or ACC Battery voltage
93
Ground ON indicator lamp Output Ignition switch ACC 0.2 V
(L)
ON 0V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(L) ACC or ON Battery voltage
96 A/T device (detention
Ground Output — Battery voltage
(Y) switch) power supply
100*1 Ground
Passenger door re-
Input
Passenger door
(P) quest switch request switch OFF (Not pressed)
JPMIA0016GB
1.0 V
ON (Pressed) 0V
101*1 Ground
Driver door request
Input
Driver door re-
(W) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
JPMIA0041GB
1.4 V
E
F
Turn signal switch LH
G
JPMIA0037GB
1.3 V
Combination
107 Combination switch switch
Ground Input Turn signal switch RH I
(O) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
J
1.3 V
JPMIA0038GB
1.3 V
M
N
Front washer switch ON
O
JPMIA0039GB
1.3 V
JPMIA0041GB
1.4 V
JPMIA0038GB
1.3 V
JPMIA0036GB
1.3 V
JPMIA0040GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
F
JPMIA0037GB
1.3 V
G
Combination
109 Combination switch switch
H
Ground Input Lighting switch 2ND
(SB) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
JPMIA0038GB
1.3 V EXL
N
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(LG) communication Output
JMKIA0066GB
JPMIA0156GB
8.7 V
When bright outside of the
Close to 5 V
113*3 Ignition switch vehicle
Ground Optical sensor signal Input
(P/B) ON When dark outside of the
Close to 0 V
vehicle
116 Fuse check (Stop
Ground Input — Battery voltage
(GR) lamp switch)
OFF (Brake pedal is not
0V
118 depressed)
Ground Stop lamp switch Input Stop lamp switch
(L) ON (Brake pedal is de-
Battery voltage
pressed)
1.1 V
UNLOCK status (unlock
0V
sensor switch ON)
121 When the key is inserted into key slot Battery voltage
Ground Key slot switch Input
(Y) When the key is not inserted into key slot 0V
122 OFF 0V
Ground ACC feedback signal Input Ignition switch
(R) ACC or ON Battery voltage
11.8 V D
ON (When passenger door
0V
opens)
E
F
132 Power window switch Input/ Ignition switch ON
Ground
(G) communication Output
JPMIA0013GB
G
10.2 V
Ignition switch OFF or ACC Battery voltage
H
ON (When tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright- I
ening/dimming level.
Push-button igni-
133 Push-button ignition
Ground Output tion switch illumi- ON (When tail lamps ON) J
(W) switch illumination
nation
K
JPMIA0159GB
OFF 0V
137 Receiver and sensor
EXL
Ground Input Ignition switch ON 0V
(P) ground
Standby state
OCC3881D
OCC3880D
JPMIA0014GB
11.3 V
OFF Battery voltage
All switch OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(L) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT
143 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(W) OUTPUT 1 switch Any of the conditions below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 JPMIA0032GB
10.7 V
All switch OFF 0V I
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS J
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH K
JPMIA0035GB
10.7 V
EXL
149*4 Ground
Tire pressure warn-
Input Ignition switch ON M
(W) ing check switch
JPMIA0011GB N
11.8 V
11.8 V
ON (When driver door
0V
opens)
EXL
JCMWM1292GB
P
JCMWM1293GB
EXL
JCMWM1294GB
JCMWM1295GB
EXL
JCMWM1296GB
JCMWM1297GB
EXL
JCMWM1298GB
P
Fail-safe INFOID:0000000003729400
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E1: ENG STATE NO RECIV
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to
EXL-23, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
Tire pressure
Freeze Frame Intelligent Key Reference
CONSULT display Fail-safe monitor warning
Data warning lamp ON page EXL
lamp ON
No DTC is detected.
further testing — — — — —
may be required. M
U1000: CAN COMM CIRCUIT — — — — BCS-39
U1010: CONTROL UNIT (CAN) — — — — BCS-40
N
U0415: VEHICLE SPEED SIG — — — — BCS-41
B2013: ID DISCORD BCM-S/L × × — — SEC-54
B2014: CHAIN OF S/L-BCM × × — — SEC-55 O
B2190: NATS ANTENNA AMP × — — — SEC-47
B2191: DIFFERENCE OF KEY × — — — SEC-50
P
B2192: ID DISCORD BCM-ECM × — — — SEC-51
B2193: CHAIN OF BCM-ECM × — — — SEC-53
B2553: IGNITION RELAY — × — — PCS-50
B2555: STOP LAMP — × — — SEC-58
B2556: PUSH-BTN IGN SW — × × — SEC-60
B2557: VEHICLE SPEED × × × — SEC-62
EXL
JPMIA0863ZZ
PHYSICAL VALUES
J
Ignition switch ON
21 NOTE:
Ground Ambient sensor Input
(O) Changes depending to ambient tem-
perature K
JSNIA0014GB
EXL
22 Refrigerant pressure sen- Engine • Warm-up condition
Ground Output 0V
(SB) sor ground running • Idle speed
• Warm-up condition
• Both A/C switch and M
23 Refrigerant pressure sen- Engine
Ground Output blower fan motor switch 1.0 - 4.0 V
(GR) sor running
ON
(Compressor operates)
N
24 Refrigerant pressure sen- Ignition switch OFF 0V
Ground Input
(G) sor power supply Ignition switch ON 5.0 V
Ignition switch ON
JPMIA0001GB
6.3 V
JPMIA0002GB
3.8 V
JPMIA0003GB
1.4 V
• Approximately 1 second after turning
the ignition switch ON 0 - 1.5 V
77 • Engine running
Ground Fuel pump relay control Output
(GR)
Approximately 1 second or more after
Battery voltage
turning the ignition switch ON
80
Ground Starter motor Output At engine cranking Battery voltage
(B)
H
Ignition switch ON
100 NOTE:
Ground Ambient sensor Output
(SB) Changes depending to ambient tem- I
perature
JSNIA0014GB
J
101 Refrigerant pressure sen- Engine • Warm-up condition
Ground Input 0V
(L) sor ground running • Idle speed
• Warm-up condition K
• Both A/C switch and
102 Refrigerant pressure sen- Engine
Ground Input blower fan motor switch 1.0 - 4.0 V
(B) sor running
ON
(Compressor operates) EXL
103 Refrigerant pressure sen- Ignition switch OFF 0V
Ground Output
(P) sor power supply Ignition switch ON 5.0 V
M
*: AWD models only
JCMWM1305GB
EXL
JCMWM1306GB
JCMWM1307GB
EXL
JCMWM1308GB
Fail-safe INFOID:0000000003729405 P
Voltage judgment
Ignition relay excitation coil IPDM E/R judgment Operation
Ignition relay contact side
side
ON ON Ignition relay ON normal —
OFF OFF Ignition relay OFF normal —
• Detects DTC “B2098: IGN RELAY ON”
ON OFF Ignition relay ON stuck • Turns ON the tail lamp relay for 10 min-
utes
OFF ON Ignition relay OFF stuck Detects DTC “B2099: IGN RELAY OFF”
Ignition switch Front wiper switch Front wiper auto stop signal A
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not B
ON
change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item C
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains D
active for 90 seconds.
DTC Index INFOID:0000000003729406
E
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now F
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now
- The number increases like 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF → G
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×: Applicable H
CONSULT display Fail-safe Refer to
No DTC is detected.
further testing — — I
may be required.
U1000: CAN COMM CIRCUIT × PCS-17
B2098: IGN RELAY ON × PCS-18 J
B2099: IGN RELAY OFF — PCS-19
B2108: STRG LCK RELAY ON — SEC-103
K
B2109: STRG LCK RELAY OFF — SEC-104
B210A: STRG LCK STATE SW — SEC-105
B210B: START CONT RLY ON — SEC-109 EXL
B210C: START CONT RLY OFF — SEC-110
B210D: STARTER RELAY ON — SEC-111
M
B210E: STARTER RELAY OFF — SEC-112
B210F: INTRLCK/PNP SW ON — SEC-114
B2110: INTRLCK/PNP SW OFF — SEC-116 N
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000003261570
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
XENON HEADLAMP B
• Brightness and the color of light may change slightly immediately after turning the headlamp ON until the
xenon bulb becomes stable. This is normal.
• Illumination time lag may occur between right and left. This is normal. C
AUTO LIGHT SYSTEM
The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is D
normal.
EXL
The headlamp (both sides) does not switch to the high beam when setting to the lighting switch HI or PASS.
Diagnosis Procedure INFOID:0000000003261566
EXL
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure INFOID:0000000003261363
1.CHECK FUSE
Check that the following fuse is fusing.
1.CHECK FUSE C
Check that the following fuse is fusing.
D
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #58 15 A
Is the fuse fusing? E
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> GO TO 2.
2.COMBINATION SWITCH INSPECTION F
Check the combination switch. Refer to BCS-86, "Symptom Table".
Is the combination switch normal?
G
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT H
CONSULT-III DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status. I
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000003486615
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" INFOID:0000000003486616
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precautions For Xenon Headlamp Service INFOID:0000000003261367
WARNING:
Comply with the following warnings to prevent any serious accident.
• Disconnect the battery cable (negative terminal) or the power supply fuse before installing, remov-
ing, or touching the xenon headlamp (bulb included). The xenon headlamp contains high-voltage
generated parts.
• Never work with wet hands.
• Check the xenon headlamp ON-OFF status after assembling it to the vehicle. Never turn the xenon
headlamp ON in other conditions. Connect the power supply to the vehicle-side connector.
(Turning it ON outside the lamp case may cause fire or visual impairments.)
EXL
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description INFOID:0000000003261370
JPLIA0810ZZ
JSLIA0005ZZ
EXL
5. Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
M
Horizontal center line of headlamp (H) Highest cutoff line height (M) Lowest cutoff line height (N)
700 (27.56) or less 4 (0.16) 30 (1.18)
701(27.60) – 800 (31.50) 4 (0.16) 30 (1.18) N
801 (31.54) or more 17 (0.67) 44 (1.73)
Side view
O
JSLIA0006ZZ
JPLIA0811ZZ
J
Aiming Adjustment Procedure INFOID:0000000003261373
JPLIA0008ZZ
A : Cutoff line
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp
X : Cutoff line height
ON-VEHICLE REPAIR A
FRONT COMBINATION LAMP
Exploded View INFOID:0000000003261374
B
REMOVAL
C
H
JPLIA0812ZZ
EXL
JPLIA0813ZZ
O
1. Front side marker lamp bulb 2. Front side marker lamp bulb socket 3. Resin cap
4. Seal packing 5. Xenon bulb socket (Starter) 6. Xenon bulb
7. Retaining spring 8. Seal packing 9. HID control unit (Inverter)
P
10. Parking lamp bulb socket 11. Parking lamp bulb 12. Front turn signal lamp bulb socket
13. Front turn signal lamp bulb 14. Headlamp housing assembly
Refer to GI-4, "Components" for symbols in the figure.
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1. Remove the front grille. Refer to EXT-18, "Exploded View".
2. Remove the headlamp extension panel.
3. Remove the front bumper fascia. Refer to EXT-12, "Exploded View".
4. Remove the headlamp mounting bolts.
5. Remove the harness clips from headlamp housing assembly.
6. Pull out the headlamp assembly forward the vehicle.
7. Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-158, "Description".
Replacement INFOID:0000000003261376
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Remove the fender rubber protector in engine room.
2. Rotate the resin cap counterclockwise and unlock it.
3. Rotate the bulb socket counterclockwise and unlock it.
4. Unlock the retaining spring. And then remove the bulb from the
headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
JPLIA0814ZZ
A
DISASSEMBLY
1. Rotate the resin cap counterclockwise and unlock it.
B
2. Rotate the xenon bulb socket counterclockwise and unlock it.
3. Unlock the retaining spring. And then remove the xenon bulb.
4. Remove the HID control unit installation screw. C
5. Remove the screw. And then disconnect the connector from HID control unit.
6. Remove the xenon bulb socket from headlamp housing assembly.
7. Rotate the parking lamp bulb socket counterclockwise and unlock it. D
8. Remove the bulb from parking lamp bulb socket.
9. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from front turn signal lamp bulb socket. E
11. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from front side marker lamp bulb socket.
F
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION: G
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
EXL
JPLIA0815ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the front fender protector. Keep a service area. Refer to EXT-23, "FENDER PROTECTOR :
Exploded View".
2. Remove the front fog lamp connector.
3. Remove the screw.
4. Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-161, "Description"
Replacement INFOID:0000000003261380
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1. Remove the front fender protector. Keep the service area. Refer to EXT-23, "FENDER PROTECTOR :
Exploded View".
JPLIA0816ZZ
EXL
JPLIA0818ZZ
1. Optical sensor
REMOVAL
1. Insert an appropriate tool between the optical sensor and the instrument upper panel. Pull out the optical
sensor upward.
2. Disconnect the optical sensor connector. And then remove the optical sensor.
INSTALLATION
Install in the reverse order of removal.
Lighting & turn signal switch is integrated in the combination switch. Refer to BCS-89, "Exploded View".
C
EXL
JPLIA0819ZZ
REMOVAL
1. Remove the instrument stay cover (RH). Refer to IP-11, "Exploded View".
2. Remove the screws. And then remove the switch bracket from the instrument stay cover.
3. Remove the hazard switch.
INSTALLATION
Install in the reverse order of removal.
JPLIA0820ZZ
REMOVAL
1. Remove the instrument driver lower panel. Refer to IP-11, "Exploded View". I
2. Disengage the pawls. And remove the headlamp aiming switch.
INSTALLATION J
Install in the reverse order of removal.
EXL
REMOVAL
JPLIA0821ZZ
DISASSEMBLY
JPLIA0822ZZ
1. Rear turn signal lamp bulb 2. Rear turn signal lamp bulb socket 3. Rear side marker lamp bulb socket
4. Rear side marker lamp bulb
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the rear combination lamp finisher.
2. Remove the rear combination lamp mounting bolts.
3. Pull the rear combination lamp toward outside of the vehicle. Remove the rear combination lamp.
4. Disconnect the rear combination lamp connector.
INSTALLATION
CAUTION:
• Disconnect the battery negative terminal or remove the fuse. B
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect C
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to EXL-172, "Exploded View". D
REAR SIDE MARKER LAMP BULB
1. Remove the rear combination lamp. Refer to EXL-172, "Exploded View".
E
2. Rotate the rear side marker lamp bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the rear side marker lamp bulb socket.
REAR TURN SIGNAL LAMP BULB F
1. Remove the rear combination lamp. Refer to EXL-172, "Exploded View".
2. Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
G
3. Remove the bulb from the rear turn signal lamp bulb socket.
EXL
JPLIA0823ZZ
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove the back door plate. Refer to INT-37, "Exploded View".
2. Remove the mounting nuts and connector.
3. Pull the high-mounted stop lamp toward rear of the vehicle. Remove the rear washer tube.
4. Disconnect the high-mounted stop lamp connector.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
JPLIA0824ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
I
REMOVAL
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Remove the back-up lamp mounting nuts and clip. J
3. Disconnect the back-up lamp connector. And then remove the back-up lamp.
INSTALLATION K
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
EXL
Replacement INFOID:0000000003261394
CAUTION: M
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
O
1. Remove the back-up lamp. Refer to EXL-175, "Exploded View".
JPLIA0825ZZ
JPLIA0826ZZ
H
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL I
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Remove the screw. And then disconnect the license plate lamp connector.
J
3. Remove the license plate lamp.
4. Remove the screw. And then remove the license plate lamp bracket.
INSTALLATION K
Install in the reverse order of removal.
Replacement INFOID:0000000003261397
EXL
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. M
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
N
LICENSE PLATE LAMP BULB
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Turn the license plate lamp bulb socket (1) counterclockwise O
and unlock it.
3. Remove the bulb (2) from the license plate lamp bulb socket.
P
JPLIA0827ZZ
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000003261399
B
OVERALL SEQUENCE
C
EXL
P
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
FUNCTION DIAGNOSIS A
HEADLAMP SYSTEM
System Diagram INFOID:0000000003261400
B
JPLIA0167GB
G
System Description INFOID:0000000003261401
OUTLINE H
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION I
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R with CAN communication according to the head-
lamp (LO) ON condition. J
Headlamp (LO) ON condition
- Lighting switch 2ND
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low K
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter with CAN communica- EXL
tion according to the headlamp (HI) ON condition.
Headlamp (HI) ON condition
M
- Lighting switch HI with the lighting switch 2ND
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high N
beam request signal.
JPLIA0891ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges that the headlamp is turned ON according to the vehicle condition.
BCM - Requests the headlamp relay (HI/LO) ON to IPDM E/R (with CAN communication).
- Requests the high beam indicator lamp ON to the combination meter (with CAN
communication).
Controls the integrated relay, and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Combination meter Turns the high beam indicator lamp ON according to the request from BCM (with CAN
(High beam indicator lamp) communication).
JPLIA0803GB F
G
OUTLINE
• Turns the front fog lamp ON as the daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading H
function of BCM, and relay control function of IPDM E/R.
DAYTIME RUNNING LIGHT OPERATION
• BCM detects the combination switch condition by the combination switch reading function. I
• BCM detects the vehicle condition depending on the following signals.
- Engine condition signal (received from ECM with CAN communication)
- Parking brake switch signal (received from combination meter with CAN communication) J
• BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the day-
time running light ON condition.
Daytime running light ON condition K
- While the engine running with the parking brake released
Daytime running light OFF condition
- Engine stopped EXL
- Headlamp ON (Passing included)
• IPDM E/R turns the integrated front fog lamp relay ON and turns the front fog lamp ON according to the front
fog light request signal. M
JPLIA0841ZZ
Part Description
• Detects each switch condition with the combination switch reading function.
BCM • Judges the headlamp ON/OFF status according to the vehicle condition. Requests
the front fog lamp relay ON to IPDM E/R (with CAN communication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
ECM Transmits the engine condition signal to BCM with CAN communication.
Combination meter Transmits the parking brake switch signal to BCM with CAN communication.
JPLIA0004GB F
G
OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R. H
FRONT FOG LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the front I
fog lamp ON condition.
Front fog lamp ON condition J
- Front fog lamp switch ON with headlamp ON (except for the high beam ON)
• IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the
front fog light request signal.
K
EXL
JPLIA0843ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
BCM • Judges the front fog lamp ON/OFF status according to the vehicle condition.
- Requests the front fog lamp relay ON to IPDM E/R (with CAN communication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
JPLIA0180GB F
G
OUTLINE
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM. H
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is turned ON and the I
turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
J
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is turned ON. BCM blinks the
hazard warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION K
• BCM transmits the turn indicator signal to the combination meter with CAN communication while the turn sig-
nal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn indicator signal. EXL
JPLIA0844ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges the blinks of the turn signal lamp and the hazard warning lamp from each
BCM switch status. The applicable turn signal lamp blinks.
• Requests the turn signal indicator lamp blink to the combination meter (with CAN
communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Hazard switch Inputs the hazard switch ON/OFF signal to BCM.
Combination meter Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
(Turn signal indicator lamp & buzzer) integrated buzzer according to the request from BCM (with CAN communication).
JPLIA0805GB F
G
OUTLINE
Parking, license plate, side marker and tail lamps are controlled by combination switch reading function and
headlamp control function of BCM, and relay control function of IPDM E/R. H
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter with CAN communi- I
cation according to the ON/OFF condition of the parking, license plate, side marker and tail lamps.
Parking, license plate, side marker and tail lamps ON condition J
- Lighting switch 1ST
- Lighting switch 2ND
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking lamp, license plate, side marker and
tail lamps ON according to the position light request signal. K
• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
EXL
JPLIA0892ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Judges the ON/OFF status of the parking, license plate and tail lamps according to
the vehicle condition.
BCM
- Requests the tail lamp relay ON to IPDM E/R (with CAN communication).
- Requests the tail lamp indicator lamp ON to the combination meter (with CAN com-
munication).
Controls the integrated relay and supplies voltage to the load according to the request
IPDM E/R
from BCM (with CAN communication).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
Combination meter Turns the tail lamp indicator lamp ON according to the request from BCM (with CAN
(Tail lamp indicator lamp) communication).
JPLIA1037GB F
G
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
H
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function I
JPLIA0845ZZ
Part Description
• Detects each switch condition by the combination switch reading function.
• Activates the battery saver to turn the exterior lamps OFF according to the vehicle
BCM
condition.
- Requests each relay OFF to IPDM E/R (with CAN communication).
Controls the integrated relay according to the request from BCM (with CAN communi-
IPDM E/R
cation).
Combination switch
Refer to BCS-9, "System Diagram".
(Lighting & turn signal switch)
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT* 1 × × × K
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × ×
EXL
Turn signal and hazard warning lamps FLASHER × × ×
— AIR CONDITONER*2
• Intelligent Key system M
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM × N
NVIS - NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
O
Back door opener system TRUNK × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × P
Signal buffer system SIGNAL BUFFER × ×
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
• *1:At model with Intelligent Key system this item is displayed, but is not used.
• *2: This item is displayed, but is not used.
IGN Counter
IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected.
• The number is 0 when a malfunction is detected now.
• The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition
switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000003729564
WORK SUPPORT
CUSTOM A/LIGHT SET- MODE 2 More sensitive setting than normal setting (Turns ON earlier than normal operation.) E
TING MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
*: Initial setting F
DATA MONITOR
G
Monitor item
Description
[Unit]
PUSH SW
The switch status input from push-button ignition switch H
[On/Off]
ENGINE STATE
The engine status received from ECM with CAN communication
[Stop/Stall/Crank/Run]
I
VEH SPEED 1 The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication
KEY SW-SLOT
Key switch status input from key slot J
[On/Off]
TURN SIGNAL R
[On/Off]
K
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off] EXL
HI BEAM SW
[On/Off]
HEAD LAMP SW1 M
Each switch status that BCM detects from the combination switch reading function
[On/Off]
HEAD LAMP SW2
[On/Off] N
PASSING SW
[On/Off]
AUTO LIGHT SW O
[On/Off]
FR FOG SW
[On/Off] P
RR FOG SW NOTE:
[On/Off] The item is indicated, but not monitored.
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
ACTIVE TEST
On NOTE:
DAYTIME RUNNING LIGHT
Off The item is indicated, but cannot be tested.
RH
NOTE:
CORNERING LAMP LH
The item is indicated, but cannot be tested.
Off
On NOTE:
ILL DIM SIGNAL
Off The item is indicated, but cannot be tested.
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000003729565
WORK SUPPORT
DATA MONITOR
Monitor item A
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
B
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW C
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function D
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch E
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
F
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC
Panic alarm signal status received from the remote keyless entry receiver G
[On/Off]
ACTIVE TEST
H
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. I
Off Stops the voltage to turn the turn signal lamps OFF.
EXL
JPMIA0871ZZ
Operation A
Inspection location Operation
sequence
A Oil pressure warning lamp Blinks continuously during operation of auto active test
1 Front wiper LO for 5 seconds → HI for 5 seconds B
• Parking lamps
• License plate lamps
2 • Side maker lamps 10 seconds C
• Tail lamps
• Front fog lamps
3 Headlamps LO ⇔ HI 5 times
D
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
E
Inspection in Auto Active Test Mode (Halogen Headlamp Models)
When auto active test mode is actuated, the following 5 steps are repeated 3 times.
JPMIA0872ZZ
J
Operation
Inspection location Operation
sequence K
A Oil pressure warning lamp Blinks continuously during operation of auto active test
1 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
EXL
• License plate lamps
2 • Side maker lamps 10 seconds
• Tail lamps M
• Front fog lamps
• LO 10 seconds
3 Headlamps
• HI ON ⇔ OFF 5 times
N
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
O
JPMIA0909GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R. F
ACTIVE TEST
Test item
EXL
COMPONENT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000003737072
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Di-
agnosis Procedure INFOID:0000000003729569
Terminals
(+) Voltage F
(−)
IPDM E/R (Approx.)
Connector Terminal
Ground G
E9 1 Battery voltage
Is the measurement value normal?
YES >> GO TO 3. H
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
I
Check continuity between IPDM E/R harness connectors and ground.
IPDM E/R
Continuity J
Connector Terminal
Ground
E10 12
Existed
E11 41 K
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector. EXL
Fuse list
Unit Location Fuse No. Capacity
Headlamp HI (LH) IPDM E/R #54 10 A
Headlamp HI (RH) IPDM E/R #55 10 A
Headlamp LO (LH) IPDM E/R #56 15 A
Headlamp LO (RH) IPDM E/R #57 15 A
Front fog lamp IPDM E/R #58 15 A
• Parking lamp
IPDM E/R #52 10 A
• Front side marker lamp
• Tail lamp
• Rear side marker lamp
IPDM E/R #53 10 A
• License plate lamp
• Each illumination
Stop lamp FUSE BLOCK (J/B) #7 10 A
Back-up lamp FUSE BLOCK (J/B) #4 10 A
1.CHECK FUSE
Check that the following fuses are not fusing.
Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF E
NOTE:
ON/OFF is repeated 1 second each.
Is the headlamp (HI) turned ON? F
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-207, "Diagnosis Procedure".
G
Diagnosis Procedure INFOID:0000000003261434
Terminals
Condition K
(+) (−) Voltage
IPDM E/R (Approx.)
External
Connector Terminal lamp
EXL
Battery
Hi
RH 89 voltage
Ground
Off 0V M
E345
Battery
Hi
LH 90 voltage
Off 0V N
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3. O
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF. P
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the headlamp high harness connector.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 89
E345 Not existed
LH 90
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
5.CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the headlamp high connector.
3. Check continuity between the headlamp high harness connector and ground.
Headlamp high
Continuity
Connector Terminal
Ground
RH E317 2
Existed
LH E316 2
Does continuity exist?
YES >> Replace the headlamp (HI) bulb. (Bulb socket is abnormally.)
NO >> Repair the harnesses or connectors.
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF E
Is the headlamp (LO) turned ON?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-209, "Diagnosis Procedure". F
Terminals J
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
External K
Connector Terminal lamp
Battery volt-
Lo
RH 83 age EXL
Ground
Off 0V
E345
Battery volt-
Lo
LH 84 age M
Off 0V
Is the measurement value normal?
N
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT O
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the headlamp low harness connector.
P
IPDM E/R
Continuity
Connector Terminal
Ground
RH 83
E345 Not existed
LH 84
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
5.CHECK HEADLAMP (LO) GROUND OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the headlamp low connector.
3. Check continuity between the headlamp low harness connector and ground.
Headlamp low
Continuity
Connector Terminal
Ground
RH E321 2
Existed
LH E320 2
Does continuity exist?
YES >> Replace the headlamp (LO) bulb. (Bulb socket is abnormally.)
NO >> Repair the harnesses or connectors.
Terminals
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
EXTERNAL
Connector Terminal LAMP
Battery
Fog
RH 86 voltage
Ground
Off 0V
E345
Battery
Fog
LH 87 voltage
Off 0V
Is the measurement value normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK FRONT FOG LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front fog lamp harness connector.
Terminals
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
EXTERNAL
Connector Terminal LAMP
Battery
TAIL
RH 91 voltage
Ground
Off 0V
E346
Battery
TAIL
LH 92 voltage
Off 0V
Is the measurement value normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front combination lamp harness con-
nector.
NOTE: B
Check the parking lamp circuit if the parking lamp and the front side marker lamp are not turned ON. Refer to
EXL-46, "Component Function Check".
1.CHECK FRONT SIDE MARKER LAMP OPERATION C
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to .PCS-11, "Diagnosis Description"
2. Check that the front side marker lamp is turned ON. D
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMP” of IPDM E/R active test item.
2. With operating the test items, check that the front side marker lamp is turned ON. E
IPDM E/R
Continuity M
Connector Terminal
Ground
RH 91
E346 Not existed
LH 92 N
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if fusing is found again.) O
Terminals
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
EXTERNAL
Connector Terminal LAMP
Battery
TAIL
RH 91 voltage
Ground
Off 0V
E346
Battery
TAIL
LH 92 voltage
Off 0V
Is the measurement value normal?
YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between the IPDM E/R harness connector and the front side marker lamp harness con-
nector.
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is B
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
C
Component Function Check INFOID:0000000003425063
Terminals
Condition M
(+) (−)
Voltage (Approx.)
BCM Turn signal
Connector Terminal switch
N
RH 17
Ground
O
LH or RH
M119
LH 18
P
PKID0926E
OFF 0V
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace BCM. Refer to BCS-88, "Exploded View".
BCM
Continuity
Connector Terminal
Ground
RH 17
M119 Not existed
LH 18
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 5.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between the front combination lamp, or the rear combination lamp and the ground.
Front turn signal lamp
H
Terminals
Condition
(+) (−)
Voltage (Approx.)
BCM I
Hazard switch
Connector Terminal
ON 0V
J
Ground
M122 110 K
OFF
JPMIA0154GB
EXL
Hazard switch
Continuity
Connector Terminal Ground
M45 2 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> GO TO 4.
4.CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between the hazard switch harness connector and the ground.
Hazard switch
Continuity
Connector Terminal Ground
M45 1 Existed
Does continuity exist?
YES >> Replace the hazard switch.
NO >> Repair the harnesses or connectors.
NOTE: B
Check the license plate lamp circuit if the tail lamp and the license plate lamp are not turned ON. Refer to EXL-
223, "Component Function Check".
1.CHECK TAIL LAMP OPERATION C
IPDM E/R AUTO ACTIVE TEST
1. Activate IPDM E/R auto active test. Refer to PCS-11, "Diagnosis Description".
2. Check that the tail lamp is turned ON. D
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMP” of IPDM E/R active test item.
2. With operating the test items, check that the tail lamp is turned ON. E
Terminals N
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
EXTERNAL O
Connector Terminal LAMP
Ground Battery volt-
TAIL
E10 7 age
P
Off 0V
Is the measurement value normal?
YES >> GO TO 3.
NO >> Replace IPDM E/R.
3.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn the ignition switch OFF.
JCLWM1143GB
EXL
JCLWM1144GB
JCLWM1145GB
EXL
JCLWM1146GB
JCLWM1147GB
EXL
JCLWM1148GB
JCLWM1149GB
EXL
JCLWM1150GB
JCLWM1151GB
EXL
P
JCLWM1159GB
JCLWM1160GB
EXL
JCLWM1161GB
JCLWM1162GB
EXL
JCLWM1163GB
JCLWM1164GB
EXL
JCLWM1165GB
JCLWM1172GB
EXL
JCLWM1173GB
JCLWM1174GB
EXL
JCLWM1175GB
JCLWM1176GB
EXL
JCLWM1177GB
JCLWM1166GB
EXL
JCLWM1167GB
JCLWM1168GB
EXL
P
JCLWM1169GB
JCLWM1170GB
EXL
JCLWM1171GB
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000003729580
The key ID that the key slot receives does not accord with the fourth
Yet
key ID registered to BCM.
CONFIRM ID4 N
The key ID that the key slot receives accords with the fourth key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the third
Yet O
key ID registered to BCM.
CONFIRM ID3
The key ID that the key slot receives accords with the third key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the sec-
P
Yet
ond key ID registered to BCM.
CONFIRM ID2
The key ID that the key slot receives accords with the second key
DONE
ID registered to BCM.
EXL
JPMIA0062ZZ
P
PHYSICAL VALUES
7 ON 0V
Ground Step lamp Output Step lamp
(W) OFF Battery voltage
LOCK (Actuator is activat-
Battery voltage
8 ed)
Ground All doors LOCK Output All doors
(V) Other than LOCK (Actuator
0V
is not activated)
UNLOCK (Actuator is acti-
Battery voltage
9 vated)
Ground Driver door UNLOCK Output Driver door
(G) Other than UNLOCK (Actu-
0V
ator is not activated)
UNLOCK (Actuator is acti-
Rear RH door and Battery voltage
10 Rear RH door vated)
Ground rear LH door UN- Output
(P) and rear LH door Other than UNLOCK (Actu-
LOCK 0V
ator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(LG)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position
Push-button ignition
14
Ground switch illumination Output Tail lamp
(O) ON
ground
JSNIA0010GB
17
Ground Turn signal RH Output
Ignition switch C
(G) ON Turn signal switch RH
D
PKID0926E
6.5 V
Turn signal switch OFF 0V
E
18 Ignition switch F
Ground Turn signal LH Output
(BR) ON Turn signal switch LH
G
PKID0926E
6.5 V
JMKIA0062GB M
34*1 Ground
Luggage room anten-
Output
Ignition switch
(B) na 1 (-) OFF
N
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
When the back
38*1 Ground
Rear bumper anten-
Output
door request
(L) na (-) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
When the back
39*1 Ground
Rear bumper anten-
Output
door request
(BR) na (+) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
61*1 Ground
Back door request
Input
Back door re-
(R) switch quest switch OFF (Not pressed) E
JPMIA0016GB
F
1.0 V
1.0 V
Not in stop position 0V J
K
OFF (When back door
66 closes)
Ground Back door switch Input Back door switch
(Y) EXL
JPMIA0011GB
11.8 V
ON (When back door M
0V
opens)
Pressed 0V
N
JPMIA0011GB P
11.8 V
11.8 V
ON (When rear RH door
0V
opens)
11.8 V
ON (When rear LH door
0V
opens)
JMKIA0062GB
72*1 Ground
Room antenna 2 (-)
Output
Ignition switch
(B) (center console) OFF
JMKIA0063GB
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
JMKIA0062GB
I
When the pas-
74*1 Ground
Passenger door an-
Output
senger door re-
(Y) tenna (-) quest switch is
operated with ig- J
nition switch OFF
When Intelligent Key is not
in the antenna detection
K
area
JMKIA0063GB
EXL
M
When Intelligent Key is in
the antenna detection area
N
JMKIA0062GB
When the pas-
75*1 Ground
Passenger door an-
Output
senger door re-
(LG) tenna (+) quest switch is O
operated with ig-
nition switch OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB
JMKIA0063GB
JMKIA0062GB
When the driver
77*1 Ground
Driver door antenna
Output
door request
(P) (+) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
78*1 Ground
Room antenna (-) (in-
Output
Ignition switch
(R) strument panel) OFF
JMKIA0063GB
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
During waiting
K
JMKIA0064GB
N
JMKIA0065GB
JPMIA0041GB
1.4 V
JPMIA0037GB
JPMIA0039GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0036GB
1.3 V
G
JPMIA0037GB
I
1.3 V
JPMIA0039GB
1.3 V EXL
1.3 V
Push-button igni- Pressed 0V O
89 Push-button ignition
Ground Input tion switch (push
(BR) switch (push switch) Not pressed Battery voltage
switch)
90 Input/ P
Ground CAN - L — —
(P) Output
91 Input/
Ground CAN - H — —
(L) Output
92
Key slot illumina-
(R)*1 Ground Key slot illumination Output Blinking
tion
(L)*2
JPMIA0015GB
6.5 V
ON 0V
OFF or ACC Battery voltage
93
Ground ON indicator lamp Output Ignition switch ACC 0.2 V
(L)
ON 0V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(L) ACC or ON Battery voltage
96 A/T device (detention
Ground Output — Battery voltage
(Y) switch) power supply
100*1 Ground
Passenger door re-
Input
Passenger door
(P) quest switch request switch OFF (Not pressed)
JPMIA0016GB
1.0 V
ON (Pressed) 0V
101*1 Ground
Driver door request
Input
Driver door re-
(W) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
JPMIA0041GB
1.4 V
E
F
Turn signal switch LH
G
JPMIA0037GB
1.3 V
Combination
107 Combination switch switch
Ground Input Turn signal switch RH I
(O) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
J
1.3 V
JPMIA0038GB
1.3 V
M
N
Front washer switch ON
O
JPMIA0039GB
1.3 V
JPMIA0041GB
1.4 V
JPMIA0038GB
1.3 V
JPMIA0036GB
1.3 V
JPMIA0040GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
F
JPMIA0037GB
1.3 V
G
Combination
109 Combination switch switch
H
Ground Input Lighting switch 2ND
(SB) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
JPMIA0038GB
1.3 V EXL
N
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(LG) communication Output
JMKIA0066GB
JPMIA0156GB
8.7 V
When bright outside of the
Close to 5 V
113*3 Ignition switch vehicle
Ground Optical sensor signal Input
(P/B) ON When dark outside of the
Close to 0 V
vehicle
116 Fuse check (Stop
Ground Input — Battery voltage
(GR) lamp switch)
OFF (Brake pedal is not
0V
118 depressed)
Ground Stop lamp switch Input Stop lamp switch
(L) ON (Brake pedal is de-
Battery voltage
pressed)
1.1 V
UNLOCK status (unlock
0V
sensor switch ON)
121 When the key is inserted into key slot Battery voltage
Ground Key slot switch Input
(Y) When the key is not inserted into key slot 0V
122 OFF 0V
Ground ACC feedback signal Input Ignition switch
(R) ACC or ON Battery voltage
11.8 V D
ON (When passenger door
0V
opens)
E
F
132 Power window switch Input/ Ignition switch ON
Ground
(G) communication Output
JPMIA0013GB
G
10.2 V
Ignition switch OFF or ACC Battery voltage
H
ON (When tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright- I
ening/dimming level.
Push-button igni-
133 Push-button ignition
Ground Output tion switch illumi- ON (When tail lamps ON) J
(W) switch illumination
nation
K
JPMIA0159GB
OFF 0V
137 Receiver and sensor
EXL
Ground Input Ignition switch ON 0V
(P) ground
Standby state
OCC3881D
OCC3880D
JPMIA0014GB
11.3 V
OFF Battery voltage
All switch OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(L) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT
143 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(W) OUTPUT 1 switch Any of the conditions below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 JPMIA0032GB
10.7 V
All switch OFF 0V I
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS J
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH K
JPMIA0035GB
10.7 V
EXL
149*4 Ground
Tire pressure warn-
Input Ignition switch ON M
(W) ing check switch
JPMIA0011GB N
11.8 V
11.8 V
ON (When driver door
0V
opens)
EXL
JCMWM1292GB
P
JCMWM1293GB
EXL
JCMWM1294GB
JCMWM1295GB
EXL
JCMWM1296GB
JCMWM1297GB
EXL
JCMWM1298GB
P
Fail-safe INFOID:0000000003729582
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4 • B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E1: ENG STATE NO RECIV
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to
EXL-193, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
Tire pressure
Freeze Frame Intelligent Key Reference
CONSULT display Fail-safe monitor warning
Data warning lamp ON page EXL
lamp ON
No DTC is detected.
further testing — — — — —
may be required. M
U1000: CAN COMM CIRCUIT — — — — BCS-39
U1010: CONTROL UNIT (CAN) — — — — BCS-40
N
U0415: VEHICLE SPEED SIG — — — — BCS-41
B2013: ID DISCORD BCM-S/L × × — — SEC-54
B2014: CHAIN OF S/L-BCM × × — — SEC-55 O
B2190: NATS ANTENNA AMP × — — — SEC-47
B2191: DIFFERENCE OF KEY × — — — SEC-50
P
B2192: ID DISCORD BCM-ECM × — — — SEC-51
B2193: CHAIN OF BCM-ECM × — — — SEC-53
B2553: IGNITION RELAY — × — — PCS-50
B2555: STOP LAMP — × — — SEC-58
B2556: PUSH-BTN IGN SW — × × — SEC-60
B2557: VEHICLE SPEED × × × — SEC-62
EXL
JPMIA0863ZZ
PHYSICAL VALUES
J
Ignition switch ON
21 NOTE:
Ground Ambient sensor Input
(O) Changes depending to ambient tem-
perature K
JSNIA0014GB
EXL
22 Refrigerant pressure sen- Engine • Warm-up condition
Ground Output 0V
(SB) sor ground running • Idle speed
• Warm-up condition
• Both A/C switch and M
23 Refrigerant pressure sen- Engine
Ground Output blower fan motor switch 1.0 - 4.0 V
(GR) sor running
ON
(Compressor operates)
N
24 Refrigerant pressure sen- Ignition switch OFF 0V
Ground Input
(G) sor power supply Ignition switch ON 5.0 V
Ignition switch ON
JPMIA0001GB
6.3 V
JPMIA0002GB
3.8 V
JPMIA0003GB
1.4 V
• Approximately 1 second after turning
the ignition switch ON 0 - 1.5 V
77 • Engine running
Ground Fuel pump relay control Output
(GR)
Approximately 1 second or more after
Battery voltage
turning the ignition switch ON
80
Ground Starter motor Output At engine cranking Battery voltage
(B)
H
Ignition switch ON
100 NOTE:
Ground Ambient sensor Output
(SB) Changes depending to ambient tem- I
perature
JSNIA0014GB
J
101 Refrigerant pressure sen- Engine • Warm-up condition
Ground Input 0V
(L) sor ground running • Idle speed
• Warm-up condition K
• Both A/C switch and
102 Refrigerant pressure sen- Engine
Ground Input blower fan motor switch 1.0 - 4.0 V
(B) sor running
ON
(Compressor operates) EXL
103 Refrigerant pressure sen- Ignition switch OFF 0V
Ground Output
(P) sor power supply Ignition switch ON 5.0 V
M
*: AWD models only
JCMWM1305GB
EXL
JCMWM1306GB
JCMWM1307GB
EXL
JCMWM1308GB
Fail-safe INFOID:0000000003729587 P
Voltage judgment
Ignition relay excitation coil IPDM E/R judgment Operation
Ignition relay contact side
side
ON ON Ignition relay ON normal —
OFF OFF Ignition relay OFF normal —
• Detects DTC “B2098: IGN RELAY ON”
ON OFF Ignition relay ON stuck • Turns ON the tail lamp relay for 10 min-
utes
OFF ON Ignition relay OFF stuck Detects DTC “B2099: IGN RELAY OFF”
Ignition switch Front wiper switch Front wiper auto stop signal A
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not B
ON
change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item C
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains D
active for 90 seconds.
DTC Index INFOID:0000000003729588
E
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now F
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now
- The number increases like 1 → 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF → G
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×: Applicable H
CONSULT display Fail-safe Refer to
No DTC is detected.
further testing — — I
may be required.
U1000: CAN COMM CIRCUIT × PCS-17
B2098: IGN RELAY ON × PCS-18 J
B2099: IGN RELAY OFF — PCS-19
B2108: STRG LCK RELAY ON — SEC-103
K
B2109: STRG LCK RELAY OFF — SEC-104
B210A: STRG LCK STATE SW — SEC-105
B210B: START CONT RLY ON — SEC-109 EXL
B210C: START CONT RLY OFF — SEC-110
B210D: STARTER RELAY ON — SEC-111
M
B210E: STARTER RELAY OFF — SEC-112
B210F: INTRLCK/PNP SW ON — SEC-114
B2110: INTRLCK/PNP SW OFF — SEC-116 N
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000003261469
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure INFOID:0000000003261471
EXL
The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure INFOID:0000000003729590
1.CHECK FUSE
Check that the following fuse is fusing.
1.CHECK FUSE C
Check that the following fuse is fusing.
D
Unit Location Fuse No. Capacity
Front fog lamp IPDM E/R #58 15 A
Is the fuse fusing? E
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> GO TO 2.
2.COMBINATION SWITCH INSPECTION F
Check the combination switch. Refer to BCS-86, "Symptom Table".
Is the combination switch normal?
G
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning part.
3.CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT H
CONSULT-III DATA MONITOR
1. Select “FR FOG REQ” of IPDM E/R data monitor item.
2. With operating the front fog lamp switch, check the monitor status. I
PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000003486629
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" INFOID:0000000003486631
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
ON-VEHICLE MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
Description INFOID:0000000003261480
B
EXL
JPLIA0828ZZ
JSLIA0005ZZ
5. Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Horizontal center line of headlamp (H) Highest cutoff line height (M) Lowest cutoff line height (N)
700 (27.56) or less 4 (0.16) 30 (1.18)
701(27.60) – 800 (31.50) 4 (0.16) 30 (1.18)
801 (31.54) or more 17 (0.67) 44 (1.73)
Side view
JSLIA0006ZZ
EXL
A: UP
B: DOWN
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
JPLIA0811ZZ
JPLIA0008ZZ
A : Cutoff line A
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp B
X : Cutoff line height
EXL
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded View INFOID:0000000003261484
REMOVAL
JPLIA0812ZZ
DISASSEMBLY
JPLIA0829ZZ
1. Front side marker lamp bulb 2. Front side marker lamp bulb socket 3. Halogen bulb (LO)
4. Halogen bulb (HI) 5. Front turn signal/parking lamp bulb socket 6. Front turn signal/parking lamp bulb
7. Headlamp housing assembly
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
E
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
F
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one. G
HEADLAMP BULB (LO)
1. Remove the fender rubber protector in the engine room. H
2. Rotate the bulb counterclockwise and unlock it.
3. Disconnect the headlamp bulb connector.
4. Remove the bulb from the headlamp housing assembly. I
HEADLAMP BULB (HI)
1. Rotate the bulb counterclockwise and unlock it.
J
2. Disconnect the headlamp bulb connector.
3. Remove the bulb from the headlamp housing assembly.
FRONT TURN SIGNAL/PARKING LAMP BULB K
1. Remove the front grille. Refer to EXT-18, "Exploded View".
2. Rotate the front turn signal/parking lamp bulb socket counterclockwise and unlock it.
EXL
3. Remove the bulb from the front turn signal/parking lamp bulb socket.
FRONT SIDE MARKER LAMP BULB
1. Remove the fender rubber protector in the engine room. M
2. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
3. Remove the bulb from the front side marker lamp bulb socket.
N
Disassembly and Assembly INFOID:0000000003261487
DISASSEMBLY O
1. Rotate the headlamp bulb (LO) counterclockwise and unlock it
2. Disconnect the headlamp bulb (LO) connector. And remove the bulb from the headlamp housing assem-
bly. P
3. Rotate the headlamp bulb (HI) counterclockwise and unlock it
4. Disconnect the headlamp bulb (HI) connector. And remove the bulb from the headlamp housing assem-
bly.
5. Rotate the front turn signal/parking lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal/parking lamp bulb socket.
7. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
JPLIA0815ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse. I
REMOVAL
1. Remove the front fender protector. Keep a service area. Refer to EXT-23, "FENDER PROTECTOR :
Exploded View". J
2. Remove the front fog lamp connector.
3. Remove the screw.
K
4. Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal. EXL
NOTE:
After installation, perform aiming adjustment. Refer to EXL-314, "Description"
Replacement INFOID:0000000003729597 M
CAUTION:
• Disconnect the battery negative terminal or remove the fuse. N
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one. O
JPLIA0816ZZ
Lighting & turn signal switch is integrated in the combination switch. Refer to BCS-89, "Exploded View".
C
EXL
JPLIA0819ZZ
REMOVAL
1. Remove the instrument stay cover (RH). Refer to IP-11, "Exploded View".
2. Remove the screws. And then remove the switch bracket from the instrument stay cover.
3. Remove the hazard switch.
INSTALLATION
Install in the reverse order of removal.
REMOVAL B
JPLIA0821ZZ G
EXL
M
JPLIA0822ZZ
1. Rear turn signal lamp bulb 2. Rear turn signal lamp bulb socket 3. Rear side marker lamp bulb socket N
4. Rear side marker lamp bulb
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement integral with rear combination lamp. Refer to EXL-323, "Exploded View".
REAR SIDE MARKER LAMP BULB
1. Remove the rear combination lamp. Refer to EXL-323, "Exploded View".
2. Rotate the rear side marker lamp bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the rear side marker lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
1. Remove the rear combination lamp. Refer to EXL-323, "Exploded View".
2. Rotate the rear turn signal lamp bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the rear turn signal lamp bulb socket.
JPLIA0823ZZ
CAUTION:
Disconnect battery negative terminal or remove the fuse.
I
REMOVAL
1. Remove the back door plate. Refer to INT-37, "Exploded View".
2. Remove the mounting nuts and connector. J
3. Pull the high-mounted stop lamp toward rear of the vehicle. Remove the rear washer tube.
4. Disconnect the high-mounted stop lamp connector.
K
INSTALLATION
Install in the reverse order of removal.
CAUTION: EXL
Seal packing cannot be reused.
JPLIA0824ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Remove the back-up lamp mounting nuts and clip.
3. Disconnect the back-up lamp connector. And then remove the back-up lamp.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Replacement INFOID:0000000003729609
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
BACK-UP LAMP BULB
1. Remove the back-up lamp. Refer to EXL-326, "Exploded View".
JPLIA0825ZZ
EXL
JPLIA0826ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Remove the screw. And then disconnect the license plate lamp connector.
3. Remove the license plate lamp.
4. Remove the screw. And then remove the license plate lamp bracket.
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000003729612
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1. Remove the back door finisher inner. Refer to INT-37, "Exploded View".
2. Turn the license plate lamp bulb socket (1) counterclockwise
and unlock it.
3. Remove the bulb (2) from the license plate lamp bulb socket.
JPLIA0827ZZ
EXL