Beruflich Dokumente
Kultur Dokumente
Before Installing
This information is included as a quick reference installation guide. Refer to the control panel installation manual for
detailed system information. If the modules will be installed in an existing operational system, inform the operator and
local authority that the system will be temporarily out of service. Disconnect power to the control panel before installing
the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
General Description
CMF-300 Supervised Control Modules are intended for use in addressable, two-wire systems, where the individual address
of each module is selected using the built-in rotary switches. This module is used to switch an external power supply,
which can be a DC power supply, to notification appliances. It also supervises the wiring to the connected loads and re-
ports their status to the panel as NORMAL, OPEN, or SHORT CIRCUIT. The CMF-300 has two pairs of output termination
points available for fault-tolerant wiring and a panel-controlled LED indicator. This module can be used to replace a C304
module that has been configured for supervised wiring operation.
Compatibility Requirements
To ensure proper operation, these modules shall be connected to listed compatible system control panels only.
Mounting
The CMF-300 mounts directly to 4˝ square electrical boxes (see Figure 2A). The box must have a minimum depth of 21/8˝.
Surface mounted electrical boxes (SMB500) are available.
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)
state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communicate
with the panel before connecting circuits controlled by the module.
F300-07-00 4 I56-1189-011 F300-07-00 1 I56-1189-011
©2006 Fire•Lite Alarms, Inc Fire•Lite Alarms, Inc., One Fire-Lite Place, Northford, CT 06472, 203-484-7161
Wiring Figure 3. Typical Notification Appliance Circuit configuration, NFPA Style Y (Class B):
NOTE: All wiring must conform to applicable local codes, ordinances, and regulations. When using control modules in non-
power limited applications, the CB500 Module Barrier must be used to meet UL requirements for the separation of power- CONNECT MODULES TO LISTED COMPATIBLE SIGNAL LINE CIRCUIT (SLC)
FIRE LITE CONTROL PANELS ONLY ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED
limited and nonpower-limited terminals and wiring. The barrier must be inserted into a 4˝×4˝×21/8˝ junction box, and the 32 VDC MAX.
TWISTED PAIR
control module must be placed into the barrier and attached to the junction box (Figure 2A). The power-limited wiring must )-( IS RECOMMENDED )-(
TO NEXT FROM PANEL OR
)+( )+(
be placed into the isolated quadrant of the module barrier (Figure 2B). DEVICE PREVIOUS DEVICE
1. Install module wiring in accordance with the job drawings and appropriate wiring diagrams. CONTROL
MODULE
2. Set the address on the module per job drawings. 24 VDC CIRCUIT
DO NOT LOOP WIRE ON TERMINALS
NOTE: Some panels support extended addressing. In order to set the module above address 99 on compatible systems, 3 & 4. BREAK WIRE RUN TO PROVIDE
MODULE POLARITIES ARE SUPERVISION OF CONNECTIONS.
carefully remove the stop on the upper rotary switch with thumb in the direction shown in Figure 1. SHOWN IN ALARM
9
8 4
5
67 8 9
10
11
0
1
)-(
3 12
)+(
3. Secure module to electrical box (supplied by installer), )-( )-( 7
2
TENS
5
13
1 0 15 14
6789
2
)-( 24 VDC POWER SUPPLY
6 3
47K EOL 4
ISOLATED, REGULATED, POWER
as shown in Figure 2A. RESISTOR
5
3
2
ONES
10
4
)+(
LIMITED PER NFPA 70.
LOOP ADDRESS
A2143-00 LISTED FOR FIRE PROTECTION WITH
BATTERY BACKUP.
)+( )+(
UL LISTED EOL RELAY
SHOWN ENERGIZED
24 VDC COIL TO NEXT CONTROL MODULE
EOLR-1 FROM TERMINALS 3 & 4 OR END-OF-LINE-RELAY (EOLR). C0358-05
OF THE LAST CONTROL ONE EOLR REQUIRED PER
MODULE ON CIRCUIT 24 VDC CIRCUIT.
Figure 1A. Controls and indicators:
Figure 4. Typical fault tolerant Notification Appliance Circuit configuration, NFPA Style Z (Class A):
ONES 7
2 13
1 0 15 14 2 )+(
EOL RESISTOR IS
TENS
LOOP ADDRESS )–( )–( 6789 )–(
6 4
5
3 24 VDC POWER SUPPLY
3 )+(
INTERNAL AT 5 2
ONES
10
4
ISOLATED, REGULATED, POWER
TERMINALS 8 & 9 LOOP ADDRESS
LIMITED PER NFPA 70.
LISTED FOR FIRE PROTECTION WITH
C0218-00 BATTERY BACKUP.
)+( )+(
UL LISTED EOL RELAY TO NEXT CONTROL
SHOWN ENERGIZED MODULE OR END OF
C0359-05
24VDC COIL FROM TERMINALS 3 & 4 LINE RELAY (EOLR); ONE
EOLR-1 OF THE LAST CONTROL EOLR REQUIRED PER
Figure 2A. Module mounting with barrier: Figure 2B: MODULE ON CIRCUIT 24 VDC CIRCUIT
9
8 4 5 6 78
7T 3
9
6 EN 21
S 0
10 0
LO 1 11
OP 5 3
1
4 5 6 7 8 5 14 13 2 1
ON 2
ES 1
9 2
0 3
AD
DR 4
ES
S
9
8 4 5 6 78
7 3
9
6 TENS 2
10 10 0
LO 1211
OP 5 3
15
4 5 6 7 8 14 13 1
ON 2
ES 1
9 2
0 3
AD
DR 4
ES
S
ISOLATED
QUADRANT
C0217-00
C0219-00