Beruflich Dokumente
Kultur Dokumente
LM Position Switches
n Metal housing, one conduit entry
n Protection degree IP67 according to EN 60529
n 17 contact blocks available
n 43 actuators available
n M12 assembled connector versions
n Silver contacts gold plated versions
n Other versions available (see LR, LX, LZ datasheets)
Approvals
General data
Ambient temperature: -25°C … +80°C
Max. actuation frequency: 3600 operating cycles1/hour
Mechanical endurance: 20 million operating cycles1
Mounting position: any
Safety parameters:
B10d: 40,000,00 for NC contacts
Mechanical interlock, not coded: type 1 according to EN ISO 14119
(1) One operation cycle means two movements, one to close and one to open contacts, as defined in EN 60947‑5‑1.
Protection against short circuits: type gG fuse 4 A 500 V Direct current: DC13
Pollution degree: 3 Ue (V) 24 125 250
Ie (A) 4 1.1 0.4
Protection against short circuits: type gG fuse 2 A 500 V Direct current: DC13
Pollution degree: 3 Ue (V) 24
Ie (A) 2
www.imopc.com
TECHNICAL DATASHEET
Specifications
Rated insulation voltage (Ui): 500 Vac
400 Vac (for contact blocks C2, C11, C12, C20,
C21, C22, C33, C34)
Conventional free air thermal current (Ith): 10 A UL Approval
Protection against short circuits: type aM fuse 10 A 500 V
Utilization categories Q300 (69 VA, 125 … 250 Vdc)
Rated impulse withstand voltage (Uimp): 6 kV A600 (720 VA, 120 … 600 Vac)
4 kV (for contact blocks C20, C21, C22, C33, C34) Data of housing type 1, 4X “indoor use only”, 12, 13
Protection degree of the housing: IP67 For all contact blocks except C2 and C3 use 60 or 75°C copper (Cu) conductor, rigid or
MV terminals (screw terminals) flexible, wire size AWG 12/14. Terminal tightening torque of 7.1 lb in (0.8 Nm).
Pollution degree 3 For contact blocks C2 and C3 use 60 or 75 °C copper (Cu) conductor, rigid or flexible,
Utilization category: AC15 wire size AWG 14. Terminal tightening torque of 12 lb in (1.4 Nm).
Operating voltage (Ue): 400 Vac (50 Hz)
Operating current (Ie): 3 A In conformity with standard: UL 508, CSA 22.2 No.14
Forms of the contact element: Za, Zb, Za+Za, Y+Y, X+X, Y+Y+X, Y+Y+Y, Y+X+X
Positive opening of contacts on contact blocks C5, C6, C7, C9, C11, C13, C14, C16, C18,
C20, C21, C22, C33, C34
In conformity with standards: EN 60947‑1, EN 60947‑5‑1+ A1:2009, fundamental requirements Please contact our technical service for the list of approved products.
of the Low Voltage Directive 2006/95/EC.
Please contact our technical service for the list of approved products.
Contact block C2 Contact block C5 Contact block C6 Contact block C7 Contact block C9 Contact block C10 Contact block C11 Contact block C12 Contact block C13
1NO-1NC+1NO-1NC 1NO+1NC 1NO+1NC 1NO+1NC 2NC 2NO 2NC 2NO 2NC
1 7 1 1 1 1 1 1 1 1
2 6
2 4 2 4 2 4 2 4 2 4 2 4 2 4 2 4
3 5
4 5 5 5 5 5 5 5 5
8 3 3 3 3 3 3 3 3
M12 connector, 8 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles
Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no.
NO 3-4 NC 1-2 NC 1-2 NC 1-2 NC 1-2 NO 1-2 NC 1-2 NO 1-2 NC (1°) 1-2
NC 5-6 NO 3-4 NO 3-4 NO 3-4 NC 3-4 NO 3-4 NC 3-4 NO 3-4 NC (2°) 3-4
NC 7-8 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5 ground 5
NO 1-2
Contact block C14 Contact block C15 Contact block C16 Contact block C18 Contact block C20 Contact block C21 Contact block C22 Contact block C33 Contact block C34
2NC 2NO 2NC 1NO+1NC 2NC+1NO 3NC 1NC+2NO 1NC+1NO 2NC
1 1 1 1 1 7 1 7 1 7 1 1
2 6 2 6 2 6
2 4 2 4 2 4 2 4 2 4 2 4
3 5 3 5 3 5
5 5 5 5 4 4 4 5 5
3 3 3 3 8 8 8 3 3
M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 5 poles M12 connector, 8 poles M12 connector, 8 poles M12 connector, 8 poles M12 connector, 5 poles M12 connector, 5 poles
Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no. Contacts Pin no.
NC (1°) 1-2 NO (1°) 1-2 NC, lever at the right 1-2 NC 1-2 NC 3-4 NC 3-4 NC 3-4 NC 1-2 NC 1-2
NC (2°) 3-4 NO (2°) 3-4 NC, lever to the left 3-4 NO 3-4 NC 5-6 NC 5-6 NO 5-6 NO 3-4 NC 3-4
ground 5 ground 5 ground 5 ground 5 NO 7-8 NC 7-8 NO 7-8 ground 5 ground 5
ground 1 ground 1 ground 1
2 4
5
3
M12 connector, 5 poles
www.imopc.com
TECHNICAL DATASHEET
Selection diagram
WITH
RESET
A01-R A02-R A05-R A07-R A15-RR28 A30-R A31-R A51-R
ACTUATORS
CONDUIT ENTRY
Threaded conduit entry With cable gland With M12 metal connector
20 M20x1.5 (standard) for cables X40 8 poles, bottom
X23
PG 13.5 Ø 6…Ø 12 mm X50 5 poles, bottom
for cables
X27
Ø 3…Ø 7 mm
product options
accessory sold separately
www.imopc.com
TECHNICAL DATASHEET
LOOSE
ACTUATORS
Options & Ordering Codes Attention! The feasibility of a code number does not mean the effective availability of a product. Please contact our sales office.
LM C5 A02 3 R G 20 X50 H6
Housing Operating Temperature
polymer, one conduit entry LM Standard -25°C to +80°C
H6 Low -40°C to +80°C *
Contact Blocks
1NO+1NC, snap action C5 Preinstalled Cable Gland or Connectors
1NO+1NC, slow action C6 no cable gland or connector (standard)
1NO+1NC, slow action, overlapped C7 X21 assembled cable gland
............................... ... X50 5 poles M12 assembled metal connector
Other contact blocks available upon request
with Ø 50mm overhanging rubber roller 4 RI simultaneous reset with increased force
14
14
LS = slow action 3.6
shifted
11
Ø8
LV = slow action
40.1
40.1
31
shifted and
21.4
3
3
3
3
4.2x7.2
spaced 4.2x7.2 12.2
4.2x7.2 12.2
LI = slow action 20 12.2 20 20 20 4.2x7.2 12.2
94.5
94.5
85.4
24.2
75.8
54.4
54.4
54.4
closer
= electronic 14.2 14.2 14.2 14.2
PNP
30.8 31.5 30.8 31.5 30.8 31.5 30.8 31.5
Contact blocks
C5 R LMC5A01 1NO+1NC LMC5A02 1NO+1NC LMC5AA2 1NO+1NC LMC5AA4 1NO+1NC
With stainless steel roller on request With external rubber gasket With external rubber gasket
With stainless steel roller on request
5.5 5.5
14
14
22
52
52
22
40.5
40.5
4.2x7.2
3
4.2x7.2
3
3
3
4.2x7.2 4.2x7.2
106.4
106.4
20 12.4 12.2
94.9
54.4
54.4
www.imopc.com
TECHNICAL DATASHEET
Contact type:
R = snap action
L = slow action
LO = slow action
8.4
8.4
Ø8 12 3.8
overlapped
LS = slow action 24 24
13
shifted Ø 10 M18x1 M 18x1
25.2
R
25.2
LV = slow action
30.1
shifted and
27.9
3
3
4.2x7.2
spaced
4.2x7.2
3
3
4.2x7.2 4.2x7.2
LI = slow action 20 12.2
103
103
20 12.2 20 12.2 20 12.2
82.3
84.5
independent 22 24.2
22 24.2 22 24.2 22 24.2
LA = slow action
54.4
54.4
54.4
54.4
closer
= electronic 14.2 14.2
14.2 14.2
PNP
30.8 31.5 30.8 31.5 30.8 31.5 30.8 31.5
Contact blocks
C5 R LMC5A08 1NO+1NC LMC5A12 1NO+1NC LMC5A13 1NO+1NC LMC5A14 1NO+1NC
Roller, Ø 12 mm, stainless steel With external rubber gasket With external rubber gasket
Ø1.2
141
55
124
3.6 Ø7
195.4
20
178.4
3.8
12
40.5
3
24
24
3
4.2x7.2
20 12.2 20 20
85.9
54.4
54.4
54.4
www.imopc.com
TECHNICAL DATASHEET
With external rubber gasket With Ø 20 mm stainless steel roller on request Square rod, 3x3 mm
Contact type:
38 - 135
181.4
92.4 - 189.4
54
LV = slow action
54
shifted and 4.2x7.2
28
28
3
19
3
24
spaced
28
3
19
19
4.2x7.2
108.4
3
LI = slow action 24.2
108.4
20 12.2 20 20 24.2
independent 4.2x7.2 20 4.2x7.2 24.2
22 22
LA = slow action 22 24.2 22
54.4
54.4
54.4
closer
54.4
= electronic 14.2
14.2 14.2 14.2
PNP
30.8 31.5 30.8 31.5 30.8 31.5 30.8 31.5
Contact blocks
C5 R LMC5A25 1NO+1NC LMC5A30 1NO+1NC LMC5A33 1NO+1NC LMC5A31 1NO+1NC
C6 L LMC6A30 1NO+1NC LMC6A33 1NO+1NC LMC6A31 1NO+1NC
C7 LO LMC7A30 1NO+1NC LMC7A33 1NO+1NC LMC7A31 1NO+1NC
C9 L LMC9A30 2NC LMC9A33 2NC LMC9A31 2NC
C10 L LMC10A25 2NO LMC10A30 2NO LMC10A33 2NO LMC10A31 2NO
C11 R LMC11A30 2NC LMC11A33 2NC LMC11A31 2NC
C12 R LMC12A25 2NO LMC12A30 2NO LMC12A33 2NO LMC12A31 2NO
C13 LV LMC13A30 2NC LMC13A33 2NC LMC13A31 2NC
C14 LS LMC14A30 2NC LMC14A33 2NC LMC14A31 2NC
C15 LS LMC15A30 2NO LMC15A33 2NO LMC15A31 2NO
C16 LI LMC16A30 2NC LMC16A33 2NC LMC16A31 2NC
C18 LA LMC18A25 1NO+1NC LMC18A30 1NO+1NC LMC18A33 1NO+1NC LMC18A31 1NO+1NC
C20 L LMC20A25 1NO+2NC LMC20A30 1NO+2NC LMC20A33 1NO+2NC LMC20A31 1NO+2NC
C21 L LMC21A25 3NC LMC21A30 3NC LMC21A33 3NC LMC21A31 3NC
C22 L LMC22A25 2NO+1NC LMC22A30 2NO+1NC LMC22A33 2NO+1NC LMC22A31 2NO+1NC
C2 R LMC2A25 2x(1NO-1NC) LMC2A30 2x(1NO-1NC) LMC2A33 2x(1NO-1NC) LMC2A31 2x(1NO-1NC)
CE1 LMCE1A25 1NO-1NC LMCE1A30 1NO-1NC LMCE1A33 1NO-1NC LMCE1A31 1NO-1NC
Max. speed 1 m/s Type 1 1.5 m/s Type 1
Min. force 0.12 Nm 0.06 Nm (0.25 Nm ) 0.06 Nm 0.06 Nm (0.25 Nm )
Travel diagrams Group 4 Group 5 Group 5 Group 5
41.5 54 40
Ø3x125
20
55
7
20
125
27.5 4.5 35
Ø 7.3 29 7
38 - 135
67.6
15
179.4
59
92.4 - 189.4
28
3
28
3
28
3
19
19
113.4
4.2x7.2
4.2x7.2
122
28
3
19
4.2x7.2
19
4.2x7.2
54.4
54.4
54.4
www.imopc.com
TECHNICAL DATASHEET
Porcelain roller
Contact type:
40 40
R = snap action 41.5 20 20
L = slow action Ø9
44
20
56.5
LO = slow action 27.5
overlapped 29 7 29 7
99.3
LS = slow action
53 - 112
25
53 - 112
7
shifted
59
107.4 - 166.4
107.4 - 166.4
LV = slow action
153.7
shifted and
28
4.2x7.2
28
3
28
3
3
19
113.4
19
4.2x7.2
28
19
4.2x7.2
spaced
4.2x7.2
3
19
54.4
54.4
54.4
20
54.4
closer 20
22
= electronic
14.2 14.2 22
PNP 14.2 14.2
30.8 31.5 30.8 31.5 30.8 31.5
30.8 31.5
Contact blocks
C5 R LMC5A53 1NO+1NC LMC5A54 1NO+1NC LMC5A55 (1) 1NO+1NC LMC5A56 1NO+1NC
C6 L LMC6A53 1NO+1NC LMC6A54 1NO+1NC LMC6A55 (1) 1NO+1NC LMC6A56 1NO+1NC
C7 LO LMC7A53 1NO+1NC LMC7A54 1NO+1NC LMC7A55 (1) 1NO+1NC LMC7A56 1NO+1NC
C9 L LMC9A53 2NC LMC9A54 2NC LMC9A55 (1) 2NC LMC9A56 2NC
C10 L LMC10A53 2NO LMC10A54 2NO LMC10A55 2NO LMC10A56 2NO
C11 R LMC11A54 2NC LMC11A55 (1) 2NC LMC11A56 2NC
C12 R LMC12A53 2NO LMC12A54 2NO LMC12A55 2NO LMC12A56 2NO
C13 LV LMC13A53 2NC LMC13A54 2NC LMC13A55 (1) 2NC LMC13A56 2NC
C14 LS LMC14A53 2NC LMC14A54 2NC LMC14A55 (1) 2NC LMC14A56 2NC
C15 LS LMC15A53 2NO LMC15A54 2NO LMC15A55 2NO LMC15A56 2NO
C16 LI LMC16A54 2NC LMC16A55 (1) 2NC LMC16A56 2NC
C18 LA LMC18A53 1NO+1NC LMC18A54 1NO+1NC LMC18A55 (1) 1NO+1NC LMC18A56 1NO+1NC
C20 L LMC20A53 1NO+2NC LMC20A54 1NO+2NC LMC20A55 (1) 1NO+2NC LMC20A56 1NO+2NC
C21 L LMC21A53 3NC LMC21A54 3NC LMC21A55 (1) 3NC LMC21A56 3NC
C22 L LMC22A53 2NO+1NC LMC22A54 2NO+1NC LMC22A55 (1) 2NO+1NC LMC22A56 2NO+1NC
C2 R LMC2A53 2x(1NO-1NC) LMC2A54 2x(1NO-1NC) LMC2A55 2x(1NO-1NC) LMC2A56 2x(1NO-1NC)
CE1 LMCE1A53 1NO-1NC LMCE1A54 1NO-1NC LMCE1A55 1NO-1NC LMCE1A56 1NO-1NC
Max. speed 0.5 m/s Type 1 Type 1 Type 1
Min. force 0.03 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm ) 0.06 Nm (0.25 Nm )
Travel diagrams Group 6 Group 5 Group 5 Group 5
Ø6x200 36.5
50 12.2
38 - 208
20
92.4 - 262.4
15.3
19 7 10
62
38.8
3
28
3
19
28
3
116.4
111.5
19
4.2x7.2
4.2x7.2
20 24.2 20
20 24.2 24.2
4.2x7.2
22 22
54.4
22
54.4
54.4
14.2 14.2
14.2
30.8 31.5 30.8 31.5
30.8 31.5
Contact blocks
C5 R LMC5A57 1NO+1NC LMC5A69 1NO+1NC LMC5A76 1NO+1NC
C6 L LMC6A57 1NO+1NC LMC6A69 1NO+1NC LMC6A76 1NO+1NC
C7 LO LMC7A57 1NO+1NC LMC7A69 1NO+1NC LMC7A76 1NO+1NC
C9 L LMC9A57 2NC LMC9A69 2NC LMC9A76 2NO
C10 L LMC10A57 2NO LMC10A69 2NO LMC10A76 2NC
C11 R LMC11A57 2NC LMC11A69 2NC LMC11A76 2NO
C12 R LMC12A57 2NO LMC12A69 2NO LMC12A76 2NC
C13 LV LMC13A57 2NC LMC13A69 2NC LMC13A76 2NO
C14 LS LMC14A57 2NC LMC14A69 2NC LMC14A76 2NO
C15 LS LMC15A57 2NO LMC15A69 2NO LMC15A76 2NC
C16 LI LMC16A57 2NC LMC16A69 2NC
C18 LA LMC18A57 1NO+1NC LMC18A69 1NO+1NC LMC18A76 1NO+1NC
C20 L LMC20A57 1NO+2NC LMC20A69 1NO+2NC LMC20A76 2NO+1NC
C21 L LMC21A57 3NC LMC21A69 3NC LMC21A76 3NO
C22 L LMC22A57 2NO+1NC LMC22A69 2NO+1NC LMC22A76 1NO+2NC
C2 R LMC2A57 2x(1NO-1NC) LMC2A69 2x(1NO-1NC) LMC2A76 2x(1NO-1NC)
CE1 LMCE1A57 1NO-1NC LMCE1A69 1NO-1NC
Max. speed Type 1 1.5 m/s 0.5 m/s
Min. force 0.06 Nm (0.25 Nm ) 0.06 Nm initial 20 N - final 40 N
Travel diagrams Group 5 Group 5 Group 7
(1) All measures in the drawings are in mm
Positive opening only with actuator set to max
www.imopc.com
TECHNICAL DATASHEET
IMO Precision Controls has developed a range of position switches that incorporate a Reset device. This is denoted by the addition of the suffix R to the part numbers.
The Reset device is a block inserted between the switch body and the head, and it can be rotated and positioned in four locations independent to the head. Some of the
features of the Reset device are as follows:
• Easy integration in to almost all standard heads
• No need to use snap action contact blocks as the tripping movement is defined by the Reset device
• Rotation for ease of installation
• Two driving forces are available - standard and increased for use in applications where vibration is present
• Mechanical endurance - up to 1 million operating cycles.
Contact type: With stainless steel roller on request With stainless steel roller on request
R = snap action
L = slow action
32(29-35) 20(17-23)
5.4
5.5
5.5
14
14
22
Ø8
65
53.5
53.1
34.4
15
15
119.4
15
15
3
3
107.9
107.5
20 4.2x7.2 20 12.2
22 4.2x7.2 24.2 20 4.2x7.2
22 24.2 24.2 22 24.2
4.2x7.2
54.4
45.4 22
54.4
45.4
54.4
45.4
54.4
45.4
14.2 14.2 14.2 14.2
30.8 31.5 30.8 31.5 30.8 31.5 30.8 31.5
Contact blocks
C6 L LMC6A01-R20 1NO+1NC LMC6A02-R20 1NO+1NC LMC6A05-R20 1NO+1NC LMC6A07-R20 1NO+1NC
C9 L LMC9A01-R20 2NC LMC9A02-R20 2NC LMC9A05-R20 2NC LMC9A07-R20 2NC
C10 L LMC10A01-R20 2NO LMC10A02-R20 2NO LMC10A05-R20 2NO LMC10A07-R20 2NO
C20 L LMC20A01-R20 1NO+2NC LMC20A02-R20 1NO+2NC LMC20A05-R20 1NO+2NC LMC20A07-R20 1NO+2NC
C21 L LMC21A01-R20 3NC LMC21A02-R20 3NC LMC21A05-R20 3NC LMC21A07-R20 3NC
C22 L LMC22A01-R20 2NO+1NC LMC22A02-R20 2NO+1NC LMC22A05-R20 2NO+1NC LMC22A07-R20 2NO+1NC
C2 R LMC2A01-R20 2NO+2NC LMC2A02-R20 2NO+2NC LMC2A05-R20 2NO+2NC LMC2A07-R20 2NO+2NC
Max. speed Type 4 Type 3 Type 3 Type 3
Min. force 4.5 N (25 N ) 4 N (25 N ) 4 N (25 N ) 2.5 N (25 N )
Travel diagrams Group 1 Group 2 Group 2 Group 3
With Ø 12 mm stainless steel roller on request With Ø 20 mm stainless steel roller on request
33.2 54.9
42.1
33.2 33.2 39.4 7
16.1
20
18 18
3.8
5.4 31.1 5.4 15.6
12
72
67
67
44.5
41
41
32
41
126.4
32
32
121.4
15
121.4
15
15
3
15
3
3
3
98.9
22 24.2
54.4
54.4
45.4
54.4
39.5
14.2 14.2 14.2
14.2
30.8 31.5 30.8 31.5 30.8 31.5
30.8 31.5
Contact blocks
C6 L LMC6A15-R20 1NO+1NC LMC6A30-R20 1NO+1NC LMC6A31-R20 1NO+1NC LMC6A51-R20 1NO+1NC
C9 L LMC9A15-R20 2NC LMC9A30-R20 2NC LMC9A31-R20 2NC LMC9A51-R20 2NC
C10 L LMC10A15-R20 2NO LMC10A30-R20 2NO LMC10A31-R20 2NO LMC10A51-R20 2NO
C20 L LMC20A15-R20 1NO+2NC LMC20A30-R20 1NO+2NC LMC20A31-R20 1NO+2NC LMC20A51-R20 1NO+2NC
C21 L LMC21A15-R20 3NC LMC21A30-R20 3NC LMC21A31-R20 3NC LMC21A51-R20 3NC
C22 L LMC22A15-R20 2NO+1NC LMC22A30-R20 2NO+1NC LMC22A31-R20 2NO+1NC LMC22A51-R20 2NO+1NC
C2 R LMC2A15-R20 2NO+2NC LMC2A30-R20 2NO+2NC LMC2A31-R20 2NO+2NC LMC2A51-R20 2NO+2NC
Max. speed Type 2 Type 1 Type 1 Type 1
Min. force 4.5 N (25 N ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 1 Group 4 Group 4 Group 4
All measures in the drawings are in mm
www.imopc.com
TECHNICAL DATASHEET
Contact type:
R = snap action
33.2 40.4
L = slow action 33.2 40.4 20
7 33.2 44.4 33.2 50.4
20 7 7
20 30.1 7 20
30.1
66 - 125
26 20.1
80.6
75
72
120.4 - 179.4
41
41
41
135
41
32
32
32
32
129.4
126.4
15
15
15
15
3
3
3
3
20 4.2x7.2 12.2
24.2
20 4.2x7.2 12.2 20 4.2x7.2
12.2 20 4.2x7.2 12.2
22 22 24.2 22 24.2 22 24.2
54.4
54.4
54.4
54.4
14.2 14.2 14.2 14.2
30.8 31.5 30.8 31.5 30.8 31.5 30.8 31.5
Contact blocks
C6 L LMC6A52-R20 1NO+1NC LMC6A54-R20 1NO+1NC LMC6A56-R20 1NO+1NC LMC6A57-R20 1NO+1NC
C9 L LMC9A52-R20 2NC LMC9A54-R20 2NC LMC9A56-R20 2NC LMC9A57-R20 2NC
C10 L LMC10A52-R20 2NO LMC10A54-R20 2NO LMC10A56-R20 2NO LMC10A57-R20 2NO
C20 L LMC20A52-R20 1NO+2NC LMC20A54-R20 1NO+2NC LMC20A56-R20 1NO+2NC LMC20A57-R20 1NO+2NC
C21 L LMC21A52-R20 3NC LMC21A54-R20 3NC LMC21A56-R20 3NC LMC21A57-R20 3NC
C22 L LMC22A52-R20 2NO+1NC LMC22A54-R20 2NO+1NC LMC22A56-R20 2NO+1NC LMC22A57-R20 2NO+1NC
C2 R LMC2A52-R20 2NO+2NC LMC2A54-R20 2NO+2NC LMC2A56-R20 2NO+2NC LMC2A57-R20 2NO+2NC
Max. speed Type 1 Type 1 Type 1 Type 1
Min. force 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 4 Group 4 Group 4 Group 4
All measures in the drawings are in mm
www.imopc.com
TECHNICAL DATASHEET
M4
9
shifted
symbol aside the product code.
9
LV = slow action
shifted and
M4
41
28
3
32
19
spaced
15
LI = slow action 20
3
24.2
95.4
independent 20 4.2x7.2 12.2
4.2x7.2
22
LA = slow action
54.4
22 24.2
closer
54.4
= electronic
14.2 14.2
PNP
30.8 31.5 30.8 31.5
Contact blocks
C5 R LMC5A38-20 1NO+1NC
C6 L LMC6A38-20 1NO+1NC LMC6A38-R20 1NO+1NC
C7 LO LMC7A38-20 1NO+1NC
C9 L LMC9A38-20 2NC LMC9A38-R20 2NC
C10 L LMC10A38-20 2NO LMC10A38-R20 2NO
C11 R LMC11A38-20 2NC
C12 R LMC12A38-20 2NO
C13 LV LMC13A38-20 2NC
C14 LS LMC14A38-20 2NC
C15 LS LMC15A38-20 2NO
C16 LI LMC16A38-20 2NC
C18 LA LMC18A38-20 1NO+1NC
C20 L LMC20A38-20 1NO+2NC LMC20A38-R20 1NO+2NC
C21 L LMC21A38-20 3NC LMC21A38-R20 3NC
C22 L LMC22A38-20 2NO+1NC LMC22A38-R20 2NO+1NC
C2 R LMC2A38-20 2x(1NO-1NC) LMC2A38-R20 2NO+2NC
CE1 LMCE1A38-20 1NO-1NC
Min. force 0.06 Nm (0.25 Nm ) 0.07 Nm (0.25 Nm )
Travel diagrams Group 5 Group 4
All measures in the drawings are in mm
Technopolymer roller Technopolymer roller Adjustable square rod, Adjustable round rod Technopolymer roller
Flexible rod with pointed end
Ø 18 mm Ø 18 mm 3x3x125 mm Ø 3x125 mm Ø 20 mm
3x3x125 Ø 3x125
5 11.2 0.2 8.3 15 24
55
19 - 116
5.4 5.4
20
19 -116
4.5 5 4.5 5
18
18
106
7
40
35
35
M4
M4
M4
M4
M4
M4
2.5 11.5
Technopolymer roller Technopolymer roller Adjustable actuator with Adjustable safety actuator with Technopolymer roller
Porcelain roller Adjustable fiber glass rod
Ø 20 mm Ø 20 mm technopolymer roller technopolymer roller Ø 20 mm
Ø6x200
2.5 11.5 1 10 1 10
20
20
1 10
7 5 13.5 11 20 10 6.5
20
20
20
19 - 189
34 - 93
Ø9
7 7
34 - 93
57
43
40
7
M4
M4
M4
80
7
49
M4
M4
M4
M4
- (1) Actuator AC-CAE55 can only be used in safety applications if adjusted to its max. length, as shown in figure beside. If you need an adjustable
lever for safety applications, use the adjustable safety lever AC-CAE56.
- (2) The position switch obtained by assembling switch LM •A38-20 (e.g. LMC5A38‑20, LMC6A38‑20…) with actuator AC-CAE53 will not
93
present the same travel diagrams and actuating forces as switch LM •A53‑J0ST (e.g. LMC5A53‑J0ST, LMC6A53‑J0ST…).
- (4) The actuator cannot be rotated to the inside because it will mechanically interfere with the switch head.
www.imopc.com
TECHNICAL DATASHEET
20
20
1 10
0.8 9.5 15 24 7 5 13.5 11 20
20
20
7
20
34 - 93
20
20
7 7
34 - 93
43
40
7
M4
M4
7 7
40
49
36
M4
M4
M4
M4
M4
35
8 9.5
35
24 10.8 19.5
9.5 7 13.5 7
7 7 7
35
35
35
35
43.5 - 101
35
41.3 - 101.3
47.5
43.5
47.5
50.5
M4
56.1
M4
M4
M4
M4
M4
M4
AC-CAE31-R25 (4)
AC-CAE51-R25 (4)
AC-CAE52-R25 AC-CAE54-R25 (4)
AC-CAE55-R25 (1)
AC-CAE56-R25 AC-CAE57-R25
40
22
11.5 26 10 16
10 10
10 10
52.5 - 103.5
40
40
40
50 - 103.8
40
40
59
53
46
50
50
M4
M4
M4
M4
M4
M4
M4
AC-CAE31-R5 (4)
AC-CAE51-R5 (4)
AC-CAE52-R5 AC-CAE54-R5 (4)
AC-CAE55-R5 (1)
AC-CAE56-R5 AC-CAE57-R5 (4)
12
26 16 22
10 10 10
50
50
50
10
50
58.5 - 108
58.8 - 108
55
58
64
55
M4
M4
M4
M4
M4
M4
AC-CAE51-R26 (4)
AC-CAE2-R26 (4)
AC-CAE54-R26 (4)
AC-CAE55-R26 (1)
AC-CAE56-R26 AC-CAE57-R26 (4)
50
58.5 - 108
58.8 - 108
10 10
M4
M4
AC-CAE55-R27 (1)
AC-CAE56-R27
www.imopc.com
TECHNICAL DATASHEET
Ø
L R Ø L R Ø
Ø
60° 0.75 7 Ø
Plunger with roller - Type 5
Ø
Ø
30° 0.5 2.5 0.025
V
V
R = snap action
Ø
Ø 0.5 1 0.01
L = slow action
Ø
www.imopc.com
TECHNICAL DATASHEET
Travel Diagrams
Legend
Closed contact ! Opened contact | Positive opening travel | Pushing the switch / Releasing the switch
www.imopc.com
TECHNICAL DATASHEET
Group 7
Contact block Group 1 Group 2 Group 3 Group 4 Group 5 Group 6
inverted contacts
0 1.3 6 0 2 8 0 3 13 0 9° 0 17° 75° 0 17° 75° 0 5.4 8
2
2x(1NO-1NC) 0.7
1.1 1.6 4° 10° 10° 4.8
0 1.3 6 0 2 8 0 3 13 0 9° 0 0 3.4 8
17° 75° 17° 75° 0
3
1NO-1NC 0.8 4° 2.9
1.2 1.8 10° 10°
0 2.2 4 6 0 3.3 6 8 0 5.1 9.2 13 0 17° 0 30° 60° 75° 0 25° 55° 75° 0 3.8 8
5
1NO+1NC 1.1 6° 5
1.7 2.5 15° 10°
0 1.5 3 3.5 6 4.5 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6
6 0 2.3 8
/
8
0 1.4 2.9 6 0 2.1 4.4 8 3.2 6.7 39° 0 14° 34° 75° 3
14 13
/
0 19° 75° 0 8
2NC 3 4.5 4.5 6.8 0 6.9 10.4 60° 35° 55° 4.7
40°
0 1.4 6 2.1 0 3.2 13 19° 0 14° 75°
15 0 8
/
0 75° 0 4.7 8
2NO 3 4.5 6.9 40° 35° 3.1
0 28° 48°
16 / / / /
75°
/ /
2NC 48° 28° 75°
0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
20
1NO+2NC 2 3 4.6 14° 27° 22° 4
21 0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
3NC
0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
22
2NO+1NC 14° 4.1
2 3 4.6 27° 22°
0 1.5 3 4.5 6 0 2.3 4.56.5 8 0 3.5 6.910.2 13 0 20° 40°58° 75° 0 15° 35°53° 75° 0 1.8 4.6 8
28 /
1NO+2NC 2 3 4.6 27° 22° 4
5.5 7.5 12.5 70° 65°
0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
29 /
3NC 4.5 6.5 10.2 58° 53° 1.8
5.5 7.5 12.5 70° 65°
0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
30 /
3NC 4.5 6.5 10.2 58° 53° 1.8
5.5 7.5 12.5 70° 65°
4.5
33 0 1.5 3 6 0 2.3 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
1NO+1NC 2 3 4.6 14° 25° 20° 4.3
34 0 1.5 3 6 0 2.3 4.5 8 0 3.5 6.9 13 0 10° 0 20° 40° 75° 0 15° 35° 75° 0 4.6 8
2NC
0 3.4 4.9 6 0 5.2 7.4 8 7.8 11.2 13 0 45° 65° 75° 0 40° 60° 75° 0 2.8 8
37 0
/
1NO+1NC 1.5 2.3 3.4 18° 13° 4.9
66 0 1.4 2.9 6 0 2.1 4.4 8 0 3.2 6.7 13 0 10° 0 19° 39° 75° 0 14° 34° 75° 0 3 8
1NC
Legend
Closed contact ! Opened contact | Positive opening travel | Pushing the switch / Releasing the switch
Ref:LM-Pos-Switch-Dec15v1 Errors and omissions excepted. Subject to change without notice. www.imopc.com